Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation
Abstract
This paper presents a microstructure sensitive model for predicting mechanical response and texture evolution of metals in the dynamic recrystallization regime. A recently proposed viscoplastic self-consistent (VPSC) formulation for the prediction of recrystallization driven by strain energy and intragranular misorientation is extended to hexagonal close-packed (hcp) metals. The model is applied to the dynamic recrystallization of magnesium alloy WE43 at different temperatures and strain rates. Model predictions in terms of stress-strain response and texture evolution are compared to the experimental measurements and acceptable agreement is achieved. According to the model predictions, superplastic behavior of nuclei was found to be the dominant softening mechanism at high temperatures and low strain rates. High concentration of precipitates at the grain boundaries and presence of alloying elements are the likely causes of low boundary mobility, resulting in nucleation dominated dynamic recrystallization. Relatively strong basal compression textures indicate dominant activity of basal slip, which can be achieved only through large difference in slip resistance between soft basal and hard prismatic and pyramidal modes.
- Authors:
-
- Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
- Univ. of New Hampshire, Durham, NH (United States)
- CCDC Army Research Lab., Aberdeen Proving Ground, MD (United States)
- Publication Date:
- Research Org.:
- Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
- Sponsoring Org.:
- USDOE National Nuclear Security Administration (NNSA); USDOE-USDOD Joint Munitions Program; US Army Research Laboratory (USARL)
- OSTI Identifier:
- 1602743
- Alternate Identifier(s):
- OSTI ID: 1779321
- Report Number(s):
- LA-UR-19-28936
Journal ID: ISSN 0749-6419
- Grant/Contract Number:
- 89233218CNA000001
- Resource Type:
- Accepted Manuscript
- Journal Name:
- International Journal of Plasticity
- Additional Journal Information:
- Journal Volume: 130; Journal ID: ISSN 0749-6419
- Publisher:
- Elsevier
- Country of Publication:
- United States
- Language:
- English
- Subject:
- 36 MATERIALS SCIENCE; Microstructures; Thermomechanical processes; Constitutive behavior; Numerical algorithms; VPSC model
Citation Formats
Zecevic, Miroslav, Knezevic, Marko, McWilliams, Brandon A., and Lebensohn, Ricardo A. Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation. United States: N. p., 2020.
Web. doi:10.1016/j.ijplas.2020.102705.
Zecevic, Miroslav, Knezevic, Marko, McWilliams, Brandon A., & Lebensohn, Ricardo A. Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation. United States. https://doi.org/10.1016/j.ijplas.2020.102705
Zecevic, Miroslav, Knezevic, Marko, McWilliams, Brandon A., and Lebensohn, Ricardo A. Mon .
"Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation". United States. https://doi.org/10.1016/j.ijplas.2020.102705. https://www.osti.gov/servlets/purl/1602743.
@article{osti_1602743,
title = {Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation},
author = {Zecevic, Miroslav and Knezevic, Marko and McWilliams, Brandon A. and Lebensohn, Ricardo A.},
abstractNote = {This paper presents a microstructure sensitive model for predicting mechanical response and texture evolution of metals in the dynamic recrystallization regime. A recently proposed viscoplastic self-consistent (VPSC) formulation for the prediction of recrystallization driven by strain energy and intragranular misorientation is extended to hexagonal close-packed (hcp) metals. The model is applied to the dynamic recrystallization of magnesium alloy WE43 at different temperatures and strain rates. Model predictions in terms of stress-strain response and texture evolution are compared to the experimental measurements and acceptable agreement is achieved. According to the model predictions, superplastic behavior of nuclei was found to be the dominant softening mechanism at high temperatures and low strain rates. High concentration of precipitates at the grain boundaries and presence of alloying elements are the likely causes of low boundary mobility, resulting in nucleation dominated dynamic recrystallization. Relatively strong basal compression textures indicate dominant activity of basal slip, which can be achieved only through large difference in slip resistance between soft basal and hard prismatic and pyramidal modes.},
doi = {10.1016/j.ijplas.2020.102705},
journal = {International Journal of Plasticity},
number = ,
volume = 130,
place = {United States},
year = {Mon Feb 17 00:00:00 EST 2020},
month = {Mon Feb 17 00:00:00 EST 2020}
}
Web of Science
Works referenced in this record:
Dynamic recrystallization during high temperature deformation of magnesium
journal, August 2008
- Al-Samman, T.; Gottstein, G.
- Materials Science and Engineering: A, Vol. 490, Issue 1-2
Sheet texture modification in magnesium-based alloys by selective rare earth alloying
journal, April 2011
- Al-Samman, T.; Li, X.
- Materials Science and Engineering: A, Vol. 528, Issue 10-11
A study of microstructure-driven strain localizations in two-phase polycrystalline HCP/BCC composites using a multi-scale model
journal, November 2015
- Ardeljan, Milan; Knezevic, Marko; Nizolek, Thomas
- International Journal of Plasticity, Vol. 74
Effect of grain boundaries on texture formation during dynamic recrystallization of magnesium alloys
journal, April 2017
- Barrett, Christopher D.; Imandoust, Aidin; Oppedal, Andrew L.
- Acta Materialia, Vol. 128
A dislocation-based constitutive law for pure Zr including temperature effects
journal, May 2008
- Beyerlein, I. J.; Tomé, C. N.
- International Journal of Plasticity, Vol. 24, Issue 5
Demonstration of alloying, thermal activation, and latent hardening effects on quasi-static and dynamic polycrystal plasticity of Mg alloy, WE43-T5, plate
journal, June 2016
- Bhattacharyya, J. J.; Wang, F.; Wu, P. D.
- International Journal of Plasticity, Vol. 81
Deformation and fracture behavior of Mg alloy, WE43, after various aging heat treatments
journal, September 2017
- Bhattacharyya, J. J.; Wang, F.; McQuade, P. J.
- Materials Science and Engineering: A, Vol. 705
Static elastic and thermoelastic field fluctuations in multiphase composites
journal, January 1987
- Bobeth, M.; Diener, G.
- Journal of the Mechanics and Physics of Solids, Vol. 35, Issue 2
Effect of rare earth elements on the microstructure and texture development in magnesium–manganese alloys during extrusion
journal, October 2010
- Bohlen, Jan; Yi, Sangbong; Letzig, Dietmar
- Materials Science and Engineering: A, Vol. 527, Issue 26
Geometrical considerations concerning the structural irregularities to be assumed in a crystal
journal, January 1940
- Burgers, J. M.
- Proceedings of the Physical Society, Vol. 52, Issue 1
Hot deformation characteristics of AZ80 magnesium alloy: Work hardening effect and processing parameter sensitivities
journal, February 2017
- Cai, Y.; Wan, L.; Guo, Z. H.
- Materials Science and Engineering: A, Vol. 687
Bulk texture evolution of nanolamellar Zr–Nb composites processed via accumulative roll bonding
journal, June 2015
- Carpenter, J. S.; Nizolek, T.; McCabe, R. J.
- Acta Materialia, Vol. 92
Bone–implant interface strength and osseointegration: Biodegradable magnesium alloy versus standard titanium control
journal, January 2011
- Castellani, Christoph; Lindtner, Richard A.; Hausbrandt, Peter
- Acta Biomaterialia, Vol. 7, Issue 1
Modelling discontinuous dynamic recrystallization using a physically based model for nucleation
journal, October 2009
- Cram, D. G.; Zurob, H. S.; Brechet, Y. J. M.
- Acta Materialia, Vol. 57, Issue 17
Current issues in recrystallization: a review
journal, November 1997
- Doherty, R. D.; Hughes, D. A.; Humphreys, F. J.
- Materials Science and Engineering: A, Vol. 238, Issue 2
Mechanical response, twinning, and texture evolution of WE43 magnesium-rare earth alloy as a function of strain rate: Experiments and multi-level crystal plasticity modeling
journal, September 2019
- Feather, William G.; Ghorbanpour, Saeede; Savage, Daniel J.
- International Journal of Plasticity, Vol. 120
Correlation of plastic deformation and dynamic recrystallization in magnesium alloy ZK60
journal, April 2001
- Galiyev, A.; Kaibyshev, R.; Gottstein, G.
- Acta Materialia, Vol. 49, Issue 7
On the microstructural factors affecting creep resistance of die-cast Mg–La-rare earth (Nd, Y or Gd) alloys
journal, October 2016
- Gavras, S.; Zhu, S. M.; Nie, J. F.
- Materials Science and Engineering: A, Vol. 675
Effect of hot working and aging heat treatments on monotonic, cyclic, and fatigue behavior of WE43 magnesium alloy
journal, February 2019
- Ghorbanpour, Saeede; McWilliams, Brandon A.; Knezevic, Marko
- Materials Science and Engineering: A, Vol. 747
The Adiabatic Correction Factor for Deformation Heating During the Uniaxial Compression Test
journal, December 2001
- Goetz, R. L.; Semiatin, S. L.
- Journal of Materials Engineering and Performance, Vol. 10, Issue 6
Role of Solute in the Texture Modification During Hot Deformation of Mg-Rare Earth Alloys
journal, October 2011
- Hadorn, Jason P.; Hantzsche, Kerstin; Yi, Sangbong
- Metallurgical and Materials Transactions A, Vol. 43, Issue 4
Effect of rare earth additions on microstructure and texture development of magnesium alloy sheets
journal, October 2010
- Hantzsche, K.; Bohlen, J.; Wendt, J.
- Scripta Materialia, Vol. 63, Issue 7
Superior light metals by texture engineering: Optimized aluminum and magnesium alloys for automotive applications
journal, February 2013
- Hirsch, J.; Al-Samman, T.
- Acta Materialia, Vol. 61, Issue 3
A review on the effect of rare-earth elements on texture evolution during processing of magnesium alloys
journal, September 2016
- Imandoust, A.; Barrett, C. D.; Al-Samman, T.
- Journal of Materials Science, Vol. 52, Issue 1
Dynamic recrystallisation and the development of microstructure during the high temperature deformation of magnesium
journal, October 1982
- Ion, S. E.; Humphreys, F. J.; White, S. H.
- Acta Metallurgica, Vol. 30, Issue 10
Deformation twinning in rolled WE43-T5 rare earth magnesium alloy: Influence on strain hardening and texture evolution
journal, June 2017
- Jahedi, Mohammad; McWilliams, Brandon A.; Moy, Paul
- Acta Materialia, Vol. 131
Rate and temperature dependent deformation behavior of as-cast WE43 magnesium-rare earth alloy manufactured by direct-chill casting
journal, January 2018
- Jahedi, Mohammad; McWilliams, Brandon A.; Kellogg, Franklin R.
- Materials Science and Engineering: A, Vol. 712
Deformation and fracture mechanisms in WE43 magnesium-rare earth alloy fabricated by direct-chill casting and rolling
journal, May 2018
- Jahedi, Mohammad; McWilliams, Brandon A.; Knezevic, Marko
- Materials Science and Engineering: A, Vol. 726
Modeling the temperature dependent effect of twinning on the behavior of magnesium alloy AZ31B sheet
journal, July 2007
- Jain, A.; Agnew, S. R.
- Materials Science and Engineering: A, Vol. 462, Issue 1-2
Microstructure and mechanical properties of WE43 magnesium alloy fabricated by direct-chill casting
journal, January 2017
- Jiang, H. S.; Zheng, M. Y.; Qiao, X. G.
- Materials Science and Engineering: A, Vol. 684
Phase mixture modeling of the strain rate dependent mechanical behavior of nanostructured materials
journal, February 2005
- Kim, Hyoung Seop; Estrin, Yuri
- Acta Materialia, Vol. 53, Issue 3
Plastic deformation behaviour of fine-grained materials
journal, January 2000
- Kim, H. S.; Estrin, Y.; Bush, M. B.
- Acta Materialia, Vol. 48, Issue 2
Deformation twinning in AZ31: Influence on strain hardening and texture evolution
journal, November 2010
- Knezevic, Marko; Levinson, Amanda; Harris, Ryan
- Acta Materialia, Vol. 58, Issue 19
A numerical procedure enabling accurate descriptions of strain rate-sensitive flow of polycrystals within crystal visco-plasticity theory
journal, August 2016
- Knezevic, Marko; Zecevic, Miroslav; Beyerlein, Irene J.
- Computer Methods in Applied Mechanics and Engineering, Vol. 308
Physics and phenomenology of strain hardening: the FCC case
journal, January 2003
- Kocks, U. F.; Mecking, H.
- Progress in Materials Science, Vol. 48, Issue 3
A polycrystal plasticity model based on the mechanical threshold
journal, October 2002
- Kok, S.; Beaudoin, A. J.; Tortorelli, D. A.
- International Journal of Plasticity, Vol. 18, Issue 5-6
Residual stresses and stored elastic energy of composites and polycrystals
journal, January 1990
- Kreher, Wolfgang
- Journal of the Mechanics and Physics of Solids, Vol. 38, Issue 1
A self-consistent anisotropic approach for the simulation of plastic deformation and texture development of polycrystals: Application to zirconium alloys
journal, September 1993
- Lebensohn, R. A.; Tomé, C. N.
- Acta Metallurgica et Materialia, Vol. 41, Issue 9
On the accuracy of the self-consistent approximation for polycrystals: comparison with full-field numerical simulations
journal, October 2004
- Lebensohn, R. A.; Liu, Y.; Ponte Castañeda, P.
- Acta Materialia, Vol. 52, Issue 18
A viscoplastic micromechanical model for the yield strength of nanocrystalline materials
journal, January 2007
- Lebensohn, R.; Bringa, E.; Caro, A.
- Acta Materialia, Vol. 55, Issue 1
Self-consistent modelling of the mechanical behaviour of viscoplastic polycrystals incorporating intragranular field fluctuations
journal, August 2007
- Lebensohn, R. A.; Tomé, C. N.; CastaÑeda, P. Ponte
- Philosophical Magazine, Vol. 87, Issue 28
Average intragranular misorientation trends in polycrystalline materials predicted by a viscoplastic self-consistent approach
journal, February 2016
- Lebensohn, Ricardo A.; Zecevic, Miroslav; Knezevic, Marko
- Acta Materialia, Vol. 104
Characterization of precipitate phases in a Mg–Dy–Gd–Nd alloy
journal, July 2007
- Li, Dehui; Dong, Jie; Zeng, Xiaoqin
- Journal of Alloys and Compounds, Vol. 439, Issue 1-2
Effect of rare-earth element Sm on the corrosion behavior of Mg-6Al-1.2Y-0.9Nd alloy
journal, November 2010
- Li, Quan’an; Li, Xiaofeng; Zhang, Qing
- Rare Metals, Vol. 29, Issue 6
Texture and microstructure development during hot deformation of ME20 magnesium alloy: Experiments and simulations
journal, October 2011
- Li, X.; Al-Samman, T.; Mu, S.
- Materials Science and Engineering: A, Vol. 528, Issue 27
An affine formulation for the prediction of the effective properties of nonlinear composites and polycrystals
journal, June 2000
- Masson, R.; Bornert, M.; Suquet, P.
- Journal of the Mechanics and Physics of Solids, Vol. 48, Issue 6-7
Microstructure effects on the recrystallization of low-symmetry alpha-uranium
journal, October 2015
- McCabe, R. J.; Richards, A. W.; Coughlin, D. R.
- Journal of Nuclear Materials, Vol. 465
Kinetics of flow and strain-hardening
journal, November 1981
- Mecking, H.; Kocks, U. F.
- Acta Metallurgica, Vol. 29, Issue 11
Structure evolution of a WE43 Mg alloy submitted to different thermal treatments
journal, April 2008
- Mengucci, P.; Barucca, G.; Riontino, G.
- Materials Science and Engineering: A, Vol. 479, Issue 1-2
Microstructural evolution and superplasticity of rolled Mg-9Al-1Zn
journal, October 2000
- Mohri, T.; Mabuchi, M.; Nakamura, M.
- Materials Science and Engineering: A, Vol. 290, Issue 1-2
A self consistent approach of the large deformation polycrystal viscoplasticity
journal, December 1987
- Molinari, A.; Canova, G. R.; Ahzi, S.
- Acta Metallurgica, Vol. 35, Issue 12
Modelling of work hardening and stress saturation in FCC metals
journal, July 1997
- Nes, Erik
- Progress in Materials Science, Vol. 41, Issue 3
Characterisation of strengthening precipitate phases in a Mg–Y–Nd alloy
journal, May 2000
- Nie, J. F.; Muddle, B. C.
- Acta Materialia, Vol. 48, Issue 8
Characterisation of precipitate phases in magnesium alloys using electron microdiffraction
journal, January 2001
- Nie, J. F.; Xiao, X. L.; Luo, C. P.
- Micron, Vol. 32, Issue 8
Microstructural evolution and grain boundary sliding in a superplastic magnesium AZ31 alloy
journal, August 2009
- Panicker, R.; Chokshi, A. H.; Mishra, R. K.
- Acta Materialia, Vol. 57, Issue 13
Thermally-activated constitutive model including dislocation interactions, aging and recovery for strain path dependence of solid solution strengthened alloys: Application to AA5754-O
journal, December 2015
- Pham, Minh-Son; Iadicola, Mark; Creuziger, Adam
- International Journal of Plasticity, Vol. 75
Necklace formation during dynamic recrystallization: mechanisms and impact on flow behavior
journal, December 1998
- Ponge, D.; Gottstein, G.
- Acta Materialia, Vol. 46, Issue 1
Modeling of flow stress for magnesium alloy during hot deformation
journal, April 2010
- Qin, Yin-Jiang; Pan, Qing-Lin; He, Yun-Bin
- Materials Science and Engineering: A, Vol. 527, Issue 10-11
Constitutive modeling for the dynamic recrystallization evolution of AZ80 magnesium alloy based on stress–strain data
journal, October 2011
- Quan, Guo-Zheng; Shi, Yu; Wang, Yi-Xin
- Materials Science and Engineering: A, Vol. 528, Issue 28
Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions
journal, March 2014
- Sakai, Taku; Belyakov, Andrey; Kaibyshev, Rustam
- Progress in Materials Science, Vol. 60
New experimental insight into the mechanisms of nanoplasticity
journal, November 2013
- Skrotzki, W.; Eschke, A.; Jóni, B.
- Acta Materialia, Vol. 61, Issue 19
Structural aspects of high performance Mg alloys design
journal, February 2002
- Smola, B.; Stulı́ková, I.; von Buch, F.
- Materials Science and Engineering: A, Vol. 324, Issue 1-2
The origin of “rare earth” texture development in extruded Mg-based alloys and its effect on tensile ductility
journal, November 2008
- Stanford, N.; Barnett, M. R.
- Materials Science and Engineering: A, Vol. 496, Issue 1-2
Superplasticity and grain boundary sliding characteristics in two stage deformation of Mg–3Al–1Zn alloy sheet
journal, January 2003
- Tan, J. C.; Tan, M. J.
- Materials Science and Engineering: A, Vol. 339, Issue 1-2
Superplasticity of a Particle-Strengthened WE43 Magnesium Alloy
journal, January 2001
- Watanabe, Hiroyuki; Mukai, Toshiji; Ishikawa, Koichi
- MATERIALS TRANSACTIONS, Vol. 42, Issue 1
Mechanical Properties of Mg-Y-Zn Alloy Processed by Equal-Channel-Angular Extrusion
journal, January 2003
- Watanabe, Hiroyuki; Mukai, Toshiji; Kamado, Shigeharu
- MATERIALS TRANSACTIONS, Vol. 44, Issue 4
Elastic and damping properties from room temperature to 673 K in an AZ31 magnesium alloy
journal, August 2004
- Watanabe, Hiroyuki; Mukai, Toshiji; Sugioka, Masami
- Scripta Materialia, Vol. 51, Issue 4
A deformation-based model for recrystallization of anisotropic materials
journal, August 1997
- Wenk, H. -R.; Canova, G.; Bréchet, Y.
- Acta Materialia, Vol. 45, Issue 8
Mechanical behaviour and microstructural evolution of magnesium alloy AZ31 in tension at different temperatures
journal, May 2006
- Yi, S. B.; Zaefferer, S.; Brokmeier, H. -G.
- Materials Science and Engineering: A, Vol. 424, Issue 1-2
Transitioning rate sensitivities across multiple length scales: Microstructure-property relationships in the Taylor cylinder impact test on zirconium
journal, September 2016
- Zecevic, Miroslav; Beyerlein, Irene J.; McCabe, Rodney J.
- International Journal of Plasticity, Vol. 84
Predicting intragranular misorientation distributions in polycrystalline metals using the viscoplastic self-consistent formulation
journal, November 2017
- Zecevic, Miroslav; Pantleon, Wolfgang; Lebensohn, Ricardo A.
- Acta Materialia, Vol. 140
Modeling of intragranular misorientation and grain fragmentation in polycrystalline materials using the viscoplastic self-consistent formulation
journal, October 2018
- Zecevic, Miroslav; Lebensohn, Ricardo A.; McCabe, Rodney J.
- International Journal of Plasticity, Vol. 109
Modelling recrystallization textures driven by intragranular fluctuations implemented in the viscoplastic self-consistent formulation
journal, February 2019
- Zecevic, Miroslav; Lebensohn, Ricardo A.; McCabe, Rodney J.
- Acta Materialia, Vol. 164
Deformation behavior and dynamic recrystallization of a Mg–Zn–Y–Zr alloy
journal, July 2006
- Zhang, Ya; Zeng, Xiaoqing; Lu, Chen
- Materials Science and Engineering: A, Vol. 428, Issue 1-2
Role of Grain Boundary Sliding in Texture Evolution for Nanoplasticity
journal, August 2017
- Zhao, Yajun; Toth, Laszlo S.; Massion, Roxane
- Advanced Engineering Materials, Vol. 20, Issue 4