12 Search Results

This study investigates the inert Hugoniot response, mechanical ignition, and reaction dynamics of Ni(V)+Al multilayers during longitudinal, laser-driven shock compression experiments. Ni(V)+Al multilayers, known for their self-propagating exothermic reactions, were subjected to longitudinal stresses exceeding 50 GPa using the laser shock facility within the Dynamic Compression Sector (DCS) at the Advanced Photon Source (APS). In situ x-ray diffraction (XRD) revealed that Ni(V) and Al were not in equilibrium during compression, with stress discrepancies attributed to twinning, grain structure effects, and/or dislocation density. However, the measured inert Hugoniot closely matched prior experimental and computational studies, confirming the utility of XRD formore » measuring the equation of state of thin, complex materials. Additionally, reaction was observed at significantly higher stresses than reported previously using laser-launched flyers. This discrepancy suggests a strong influence of externally imposed shear stress on reaction thresholds, which likely arose from deviations in flyer planarity during past experiments. Full reaction of the multilayer occurred within 40 ns after shock-wave passage, evidenced by complete melting of the constituents. Eulerian hydrocode simulations replicated experimental conditions, providing insights into equilibrium dynamics and experimental artifacts. The results highlight how even small shear forces facilitate ignition in Ni(V)+Al multilayers at lower stresses.« less

We present a series of plate-impact experiments on 17-4 stainless steel to study the effect of manufacturing method and heat treatment on the Hugoniot elastic limit (HEL), Hugoniot, phase transformation stress, and spallation strength. Two traditional manufacturing methods were considered, wrought processing and casting, as well as two additive manufacturing methods, laser powder-bed fusion (LPBF) and wire-fed electron beam (EBAM). For both LPBF and EBAM 17-4 stainless steel variants, two billets were printed, enabling the application of two unique heat treatments. The HEL stress depended heavily on the thermal history, with the HEL increasing after the formation of Cu-rich precipitatesmore » via heat treatment. The Hugoniot response both below and above the phase transition was unaffected by the manufacturing method or heat treatment. The phase transition stress depended heavily on the thermal history, with its variation being attributed to the presence of various microstructural features. This is supported by a marked increase in the phase transition stress after precipitation hardening. These results suggest that the notion of the phase transition stress being dictated by bulk composition is an oversimplification and the stress fields generated by the meso-scale structure are a dominant force. The spallation strength was lower in the cast material compared to all other 17-4 stainless steel variants due to the presence of brittle δ-ferrite inclusions. Additionally, a drop in the tensile strain-rate was observed in the spallation response above the phase transition stress, which was hypothesized to stem from the kinetics of the reversion to the low-pressure phase during spall.« less

In this work, we developed a chemical synthesis protocol to prepare both spherical and rod shaped YbH_x nanoparticles and infiltrate a mesoporous CMK-3 structure with YbH_x nanoparticles. The phase evolution of the YbH_x nanoparticles was monitored as a function of the pressure in a diamond anvil cell. The cell volume of the Yb atom showed an unexpected positive deviation from the calculated equation of state (EoS) for the α-phase (space group Pnma) of YbH_x. Additionally, the β-phase (space group Fm3̅m) YbH_x nanoparticles appeared to become amorphous at approximately 27 GPa, although the same behavior was not observed in the Pnmamore » (α-phase). The Pmna phase remained stable (measured up to 59.3 GPa) and showed a significantly higher than expected volume per Yb atom relative to the calculated EoS. This deviation could be attributed to the nanoscale effect on the thermodynamics of ytterbium hydride formation, which could provide a path forward to accessing higher order ytterbium hydrides (YbH_x, x > 3) at pressures much lower than in the bulk metal.« less

Both shock and shockless compression experiments were performed on laser powder bed fusion (LPBF) Ti–5Al–5V–5Mo–3Cr (Ti-5553) to peak compressive stresses near 15 GPa. Experiments were performed on the as-built material, containing a purely β (body centered cubic) microstructure, and two differing heat treatments resulting in a dual phase α (hexagonal close packed) and β microstructure. The Hugoniot, Hugoniot elastic limit (HEL), and spallation strength were measured and compared to wrought Ti-6Al-4V (Ti-64). The results indicate the LPBF Ti-5553 Hugoniot response is similar between heat treatments and to Ti-64. The HEL stress observed in the LPBF Ti-5553 was considerably higher thanmore » Ti-64, with the as-built, fully β alloy exhibiting the largest values. The spallation strength of the LPBF Ti-5553 was also similar to Ti-64. Clear evidence of initial porosity serving as initiation sites for spallation damage was observed when comparing computed tomography measurements before and after loading. Post-mortem scanning electron microscopy images of the recovered spallation samples showed no evidence of retained phase changes near the spall plane. The spall plane was found to have kinks aligned with the loading direction near areas with large concentrations of twin-like, crystallographic defects in the as-built condition. For the heat-treated samples, the concentrations of twin-like, crystallographic defects were absent, and no preference for failure at the interface between the α and β phases was observed.« less

Reaching astrophysically relevant high energy density (HED) material states in the laboratory is an ongoing effort at multiple experimental facilities. We have developed a new dynamic compression platform for the Z Pulsed Power Facility that allows for sample sizes 100s of [Formula: see text]m in thickness that accommodate multiple grains in order to fully capture bulk properties, such as material strength. A pair of experiments compressed platinum (Pt) to HED conditions and conventional inverse Lagrangian analysis as well as a recent Bayesian calibration technique were used to determine the principal isentrope to 650 GPa with density uncertainties of <2%. These lowmore » uncertainties are calculated for single sample experiments, presenting the possibility of even smaller experimental uncertainties with multiple samples the platform allows. Our new platform extends the accessible Pt ramp pressures achievable on the Z machine to over 80% of the pressure recently achieved using the National Ignition Facility planar Hohlraum platform. This new capability, the next generation evolution of the stripline platform, was made possible by advancements in both our understanding of the Z pulsed power driver and our overall magnetohydrodynamic modeling capabilities.« less

Pulsed-power generators can produce well-controlled continuous ramp compression of condensed matter for high-pressure equation-of-state studies using the magnetic loading technique. X-ray diffraction (XRD) data from dynamically compressed samples provide direct measurements of the elastic compression of the crystal lattice, onset of plastic flow, strength–strain rate dependence, structural phase transitions, and density of crystal defects, such as dislocations. Here, we present a cost-effective, compact, pulsed x-ray source for XRD measurements on pulsed-power-driven ramp-loaded samples. This combination of magnetically driven ramp compression of materials with a single, short-pulse XRD diagnostic will be a powerful capability for the dynamic materials’ community to investigatemore » in situ dynamic phase transitions critical to equation of states. Finally, we present results using this new diagnostic to evaluate lattice compression in Zr and Al and to capture signatures of phase transitions in CdS.« less

The high-pressure dynamic response of titanium dioxide (TiO₂) is not only of interest because of its numerous industrial applications but also because of its structural similarities to silica (SiO₂). We performed plate impact experiments in a two-stage light gas gun, at peak stresses from 64 to 221 GPa to determine the TiO₂ response along the Hugoniot. The lower stress experiment at 64 GPa shows an elastic behavior followed by an elastic–plastic transition, whereas the high stress experiments above 64 GPa show a single wave structure. Previous shock studies have shown the presence of high-pressure phases (HPP) I (26 GPa) andmore » HPP II (100 GPa); however, our data suggest that the HPP I phase is stable up to 150 GPa. Using a combination of data from our current study and our previous Z-data, we determine that TiO₂ likely melts on the Hugoniot at 157 GPa. Furthermore, our data confirm that TiO₂ is not highly incompressible as shown by a previous study.« less

We report here pressure induced nanocrystal coalescence of ordered lead chalcogenide nanocrystal arrays into one dimensional (1D) and 2D nanostructures. In particular, atomic crystal phase transitions and mesoscale coalescence of PbS and PbSe nanocrystals have been observed and monitored in-situ respectively by wide- and small-angle synchrotron X-ray scattering techniques. At the atomic scale, both nanocrystals underwent reversible structural transformations from cubic to orthorhombic at significantly higher pressures than those for the corresponding bulk materials. At the mesoscale, PbS nanocrystal arrays displayed a superlattice transformation from face-centered cubic to lamellar structures, while no clear mesoscale lattice transformation was observed for PbSemore » nanocrystal arrays. Intriguingly, transmission electron microscopy (TEM) showed that the applied pressure forced both spherical nanocrystals to coalesce into single crystalline 2D nanosheets and 1D nanorods. Our results confirm that pressure can be used as a straightforward approach to manipulate the interparticle spacing and engineer nanostructures with specific morphologies, and therefore provide insights into the design and functioning of new semiconductor nanocrystal structures under high-pressure conditions.« less

In this work, we have studied the pressure-induced structural and electronic phase transitions in WO₃ to 60 GPa using micro-Raman spectroscopy, synchrotron X-ray diffraction, and electrical resistivity measurements. The results indicate that WO₃ undergoes a series of phase transitions with increasing pressure: triclinic WO₃-I initially transforms to monoclinic WO₃-II (P2₁/c) at 1 GPa, involving a tetrahedral distortion in a corner-shared octahedral framework, and then to a mixed corner and edge-shared seven-coordinated WO₃-III (P2₁/c) at 27 GPa with a large volume change of ~6% and further to WO₃-IV (Pc) above 37 GPa. These structural phase transitions also accompany a significant dropmore » in resistivity from insulating WO₃-I to semiconducting WO₃-II, and poor metallic WO₃-III and IV, arising from the Jahn–Teller distortion in WO6 and the hybridization between O 2p and W 5d orbitals in WO7, respectively. Unlike its molecular analogue of MoO₃, the transitions in WO₃ show little effect on the use of different pressure transmitting media.« less