Yield strength of Ni–Al–Cr superalloy under pressure

Raju, S. V.; Godwal, B. K.; Yan, J.; Jeanloz, R.; Saxena, S. K.

doi:10.1016/j.jallcom.2015.10.092

Title: Yield strength of Ni–Al–Cr superalloy under pressure

Abstract

Ni based superalloy Ni–Al–Cr with γ and γ' phase was studied under high pressure up to 30 GPa using diamond anvil cell technique. In-situ X-ray diffraction data was collected on these alloys under hydrostatic and non-hydrostatic conditions. Cubic phase remains stable up to the highest pressure of about 30 GPa. Bulk modulus and its pressure derivative obtained from the volume compression of pressure data are K = 166.6 ± 5.8 GPa with K' set to 4 under hydrostatic conditions and K = 211.3 ± 4.7 GPa with K' set to 4 for non-hydrostatic conditions. Using lattice strain theory, maximum shear stress ‘t’ was determined from the difference between the axial and radial stress components in the sample. The magnitude of shear stress suggests that the lower limit of compressive strength increases with pressure and shows maximum yield strength of 1.8 ± 0.3 GPa at 20 GPa. Further, we have also determined yield strength using pressure gradient method. In both the methods, yield strength increases linearly with applied pressure. Here, the results are found to be in good agreement with each other and the literature values at ambient conditions.

Authors:

Raju, S. V. ^[1]; Godwal, B. K. ^[2]; Yan, J. ^[3]; Jeanloz, R. ^[2]; Saxena, S. K. ^[1]

Florida International University, Miami, FL (United States)
University of California, Berkeley, CA (United States)
Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States); University of California, Santa Cruz, CA (United States)

Publication Date:: Fri Oct 23 00:00:00 EDT 2015

Research Org.:: Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States)

Sponsoring Org.:: USDOE National Nuclear Security Administration (NNSA); USDOE Office of Science (SC), Basic Energy Sciences (BES)

OSTI Identifier:: 1579839

Alternate Identifier(s):: OSTI ID: 1359225

Grant/Contract Number:: AC02-05CH11231; NA0001974; FG02-99ER45775; AC02-06CH11357; FA9550-12-1-0456

Resource Type:: Accepted Manuscript

Journal Name:: Journal of Alloys and Compounds

Additional Journal Information:: Journal Volume: 657; Journal Issue: C; Journal ID: ISSN 0925-8388

Publisher:: Elsevier

Country of Publication:: United States

Language:: English

Subject:: 36 MATERIALS SCIENCE; metals and alloys; rapid-solidification; quenching; elasticity; mechanical properties; strain; high pressure; x-ray diffraction

Citation Formats


                    Raju, S. V., Godwal, B. K., Yan, J., Jeanloz, R., and Saxena, S. K. Yield strength of Ni–Al–Cr superalloy under pressure.  United States: N. p., 2015. 
Web.  doi:10.1016/j.jallcom.2015.10.092.

Copy to clipboard


                    Raju, S. V., Godwal, B. K., Yan, J., Jeanloz, R., & Saxena, S. K. Yield strength of Ni–Al–Cr superalloy under pressure.  United States.  https://doi.org/10.1016/j.jallcom.2015.10.092

Copy to clipboard


                    Raju, S. V., Godwal, B. K., Yan, J., Jeanloz, R., and Saxena, S. K. Fri .  
"Yield strength of Ni–Al–Cr superalloy under pressure".  United States.  https://doi.org/10.1016/j.jallcom.2015.10.092.  https://www.osti.gov/servlets/purl/1579839.

Copy to clipboard


                    
@article{osti_1579839,

  title        = {Yield strength of Ni–Al–Cr superalloy under pressure},

  author       = {Raju, S. V. and Godwal, B. K. and Yan, J. and Jeanloz, R. and Saxena, S. K.},

  abstractNote = {Ni based superalloy Ni–Al–Cr with γ and γ' phase was studied under high pressure up to 30 GPa using diamond anvil cell technique. In-situ X-ray diffraction data was collected on these alloys under hydrostatic and non-hydrostatic conditions. Cubic phase remains stable up to the highest pressure of about 30 GPa. Bulk modulus and its pressure derivative obtained from the volume compression of pressure data are K = 166.6 ± 5.8 GPa with K' set to 4 under hydrostatic conditions and K = 211.3 ± 4.7 GPa with K' set to 4 for non-hydrostatic conditions. Using lattice strain theory, maximum shear stress ‘t’ was determined from the difference between the axial and radial stress components in the sample. The magnitude of shear stress suggests that the lower limit of compressive strength increases with pressure and shows maximum yield strength of 1.8 ± 0.3 GPa at 20 GPa. Further, we have also determined yield strength using pressure gradient method. In both the methods, yield strength increases linearly with applied pressure. Here, the results are found to be in good agreement with each other and the literature values at ambient conditions.},

  doi          = {10.1016/j.jallcom.2015.10.092},

  journal      = {Journal of Alloys and Compounds},

  number       = C,

  volume       = 657,

  place        = {United States},

  year         = {Fri Oct 23 00:00:00 EDT 2015},

  month        = {Fri Oct 23 00:00:00 EDT 2015}

}

Copy to clipboard

Journal Article:

Free Publicly Available Full Text

Accepted Manuscript (Publisher)

Accepted Manuscript (DOE)

Publisher's Version of Record

https://doi.org/10.1016/j.jallcom.2015.10.092

Other availability

Search WorldCat to find libraries that may hold this journal

Citation Metrics:

Cited by: 6 works

Citation information provided by
Web of Science

Save / Share:

Export Metadata

Save to My Library

Works referenced in this record:

Physical metallurgy of nickel aluminides
journal, February 2003

Dey, G. K.
Sadhana, Vol. 28, Issue 1-2
DOI: 10.1007/BF02717135

The effect of grain size on the yield strength of Ni3Al
journal, September 1985

Schulson, E. M.; Weihs, T. P.; Viens, D. V.
Acta Metallurgica, Vol. 33, Issue 9
DOI: 10.1016/0001-6160(85)90152-X

The yield strength of off-stoichiometric Ni3Al with and without boron
journal, December 1991

Schulson, E. M.; Xu, Y.; Munroe, P. R.
Acta Metallurgica et Materialia, Vol. 39, Issue 12
DOI: 10.1016/0956-7151(91)90029-Z

Effect of B and Cr on elastic strength and crystal structure of Ni3Al alloys under high pressure
journal, January 2015

Raju, S. V.; Oni, A. A.; Godwal, B. K.
Journal of Alloys and Compounds, Vol. 619
DOI: 10.1016/j.jallcom.2014.09.012

Thermodynamic properties of Al, Ni, NiAl, and Ni3Al from first-principles calculations
journal, May 2004

Wang, Y.; Liu, Z. -K.; Chen, L. -Q.
Acta Materialia, Vol. 52, Issue 9
DOI: 10.1016/j.actamat.2004.02.014

Shock-induced order-disorder transformation inNi3Al
journal, January 2005

Geng, H. Y.; Chen, N. X.; Sluiter, M. H. F.
Physical Review B, Vol. 71, Issue 1
DOI: 10.1103/PhysRevB.71.012105

Static strength and equation of state of rhenium at ultra-high pressures
journal, February 1991

Jeanloz, Raymond; Godwal, B. K.; Meade, Charles
Nature, Vol. 349, Issue 6311
DOI: 10.1038/349687a0

Yield strength of MgO to 40 GPa
journal, January 1988

Meade, Charles; Jeanloz, Raymond
Journal of Geophysical Research, Vol. 93, Issue B4
DOI: 10.1029/JB093iB04p03261

Yield strength of the B1 and B2 phases of NaCl
journal, January 1988

Meade, Charles; Jeanloz, Raymond
Journal of Geophysical Research, Vol. 93, Issue B4
DOI: 10.1029/JB093iB04p03270

Effect of a Coordination Change on the Strength of Amorphous SiO2
journal, August 1988

Meade, C.; Jeanloz, R.
Science, Vol. 241, Issue 4869
DOI: 10.1126/science.241.4869.1072

The lattice strains in a specimen (cubic system) compressed nonhydrostatically in an opposed anvil device
journal, May 1993

Singh, Anil K.
Journal of Applied Physics, Vol. 73, Issue 9
DOI: 10.1063/1.352809

The lattice strains in a specimen (hexagonal system) compressed nonhydrostatically in an opposed anvil high pressure setup
journal, May 1994

Singh, Anil K.; Balasingh, C.
Journal of Applied Physics, Vol. 75, Issue 10
DOI: 10.1063/1.355786

Yield strength at high pressure and temperature
journal, May 1994

Weidner, Donald J.; Wang, Yanbin; Vaughan, Michael T.
Geophysical Research Letters, Vol. 21, Issue 9
DOI: 10.1029/93GL03549

The strength of moissanite
journal, July 2002

Zhang, Jianzhong; Wang, Liping; Weidner, Donald J.
American Mineralogist, Vol. 87, Issue 7
DOI: 10.2138/am-2002-0725

Elasticity and rheology of iron above 220 GPa and the nature of the Earth's inner core
journal, December 1998

Mao, Ho-kwang; Shu, Jinfu; Shen, Guoyin
Nature, Vol. 396, Issue 6713
DOI: 10.1038/25506

Elasticity, shear strength, and equation of state of molybdenum and gold from x-ray diffraction under nonhydrostatic compression to 24 GPa
journal, December 1999

Duffy, Thomas S.; Shen, Guoyin; Shu, Jinfu
Journal of Applied Physics, Vol. 86, Issue 12
DOI: 10.1063/1.371723

X-ray diffraction study of the static strength of tungsten to $69 GPa$
journal, April 2006

He, Duanwei; Duffy, Thomas S.
Physical Review B, Vol. 73, Issue 13
DOI: 10.1103/PhysRevB.73.134106

TEM and high-temperature X-ray diffractometric studies on the structural transformations in Ni3Al
journal, September 1994

Ramesh, R.; Pathiraj, B.; Kolster, B. H.
Journal of Materials Science, Vol. 29, Issue 18
DOI: 10.1007/BF00356521

A beamline for high-pressure studies at the Advanced Light Source with a superconducting bending magnet as the source
journal, August 2005

Kunz, Martin; MacDowell, Alastair A.; Caldwell, Wendel A.
Journal of Synchrotron Radiation, Vol. 12, Issue 5
DOI: 10.1107/S0909049505020959

Equation of state and thermodynamic parameters of NaCl to 300 kbar in the high-temperature domain
journal, January 1986

Birch, Francis
Journal of Geophysical Research, Vol. 91, Issue B5
DOI: 10.1029/JB091iB05p04949

Finite Elastic Strain of Cubic Crystals
journal, June 1947

Birch, Francis
Physical Review, Vol. 71, Issue 11
DOI: 10.1103/PhysRev.71.809

The Compressibility of Media under Extreme Pressures
journal, September 1944

Murnaghan, F. D.
Proceedings of the National Academy of Sciences, Vol. 30, Issue 9
DOI: 10.1073/pnas.30.9.244

Pressure distribution in the diamond anvil press and the shear strenght of fayalite
journal, November 1977

Sung, Chien‐Min; Goetze, Christopher; Mao, Ho‐Kwang
Review of Scientific Instruments, Vol. 48, Issue 11
DOI: 10.1063/1.1134902

Microstructures and mechanical properties of a directionally solidified NiAl–Mo eutectic alloy
journal, January 2005

Bei, H.; George, E. P.
Acta Materialia, Vol. 53, Issue 1
DOI: 10.1016/j.actamat.2004.09.003

Similar Records in DOE PAGES and OSTI.GOV collections:

Deformation of binary and boron-doped Ni₃Al alloys at high pressures studied with synchrotron x-ray diffraction

Journal Article Raju, S. V. ; Vasin, R. N. ; Godwal, B. K. ; ... - Journal of Applied Physics

In situ x-ray synchrotron diffraction experiments were carried out on nickel-based high-strength superalloys under pressure to understand their deformation mechanism using a diamond anvil cell (DAC). Radial x-ray diffraction determines the room-temperature equations of state and yield strengths of binary Ni₃Al alloy and 500 ppm boron-doped Ni₃Al to pressures of 20 and 46 GPa, respectively. Crystallographic preferred orientations observed in these superalloys due to anisotropic stress field in DAC indicate the onset of plastic deformation. Inverse pole figure analysis reveals that the underlying deformation mechanisms change from an octahedral slip to a simultaneous activation of octahedral and cube slips uponmore »« less
https://doi.org/10.1063/5.0037012

Full Text Available
Strength, deformation, and equation of state of tungsten carbide to 66 GPa

Journal Article Brugman, B. L. ; Lin, F. ; Lv, M. ; ... - Acta Materialia

Here, strength, texture, and equation of state of hexagonal tungsten monocarbide (WC) have been determined under quasi-hydrostatic and non-hydrostatic compression to 66 GPa using angle-dispersive X-ray diffraction in the diamond anvil cell. Quasi-hydrostatic compression in a Ne pressure medium demonstrates that nanocrystalline WC is slightly less incompressible than bulk-scale WC, with respective bulk moduli of K₀ = 377 ± 7 and 397 ± 7 GPa and pressure derivatives K₀’ = 3.8 ± 0.3 and 3.7 ±0.3. This decrease in incompressibility with grain size is similar to behavior observed in other ceramics. Under nonhydrostatic compression, WC supports a mean differential stress of ~12-15 GPa at plastic yielding, which occurs at ~30 GPa. Strength in WC is anisotropic, with the (001) plane supporting 29-42% higher stress than stresses calculated from mean strain. Simulations using an Elasto-ViscoPlastic Self-Consistent model indicate that strength inferred from lattice strain theory may be overestimated due to effects of plastic deformation. Plastic deformation generates a texture maximum nearmore »« less
https://doi.org/10.1016/j.actamat.2021.117301

Full Text Available
Strength and equation of state of NaCl from radial x-ray diffraction

Journal Article Xiong, Lun ; Liu, Jing ; Bai, Ligang - Journal of Applied Physics

The strength and equation of state of NaCl were determined under nonhydrostatic compression up to 27 GPa using an energy-dispersive radial x-ray diffraction technique in a diamond-anvil cell using the lattice strain theory. Together with estimation of the high-pressure shear modulus, it is suggested that NaCl could support a maximum differential stress of 0.980 GPa at 22.6 GPa under uniaxial compression. The differential stress rapidly drops at 27.2 GPa due to the phase transition from B1 phase to B2 phase for NaCl. The hydrostatic compression data of B1 phase yield a bulk modulus K{sub 0} = 25.6(8) GPa and its pressure derivative K{sub 0}′ = 5.16(20) using Ptmore »« less
https://doi.org/10.1063/1.4862307
Shear-Induced Isostructural Phase Transition and Metallization of Layered Tungsten Disulfide under Nonhydrostatic Compression

Journal Article Duwal, Sakun ; Yoo, Choong-Shik - Journal of Physical Chemistry. C

Pressure-induced structural and electronic transformations of tungsten disulfide (WS₂) have been studied to 60 GPa, in both hydrostatic and non-hydrostatic conditions, using four-probe electrical resistance measurements, micro-Raman spectroscopy and synchrotron x-ray diffraction. Our results show the evidence for an isostructural phase transition from hexagonal 2H_c phase to hexagonal 2H_a phase, which accompanies the metallization at ~37 GPa. This isostructural transition occurs displacively over a large pressure range between 15 and 45 GPa and is driven by the presence of strong shear stress developed in the layer structure of WS₂ under non-hydrostatic compression. Interestingly, this transition is absent in hydrostatic conditionsmore »« less
Cited by 32
https://doi.org/10.1021/acs.jpcc.5b10759

Full Text Available
Compressibility and strength of nanocrystalline tungsten boride under compression to 60 GPa

Journal Article Haini, Dong ; Department of Geosciences, Princeton University, Princeton, New Jersey 08544 ; Dorfman, Susannah M. ; ... - Journal of Applied Physics

The compression behavior and stress state of nanocrystalline tungsten boride (WB) were investigated using radial x-ray diffraction (RXRD) in a diamond-anvil cell under non-hydrostatic compression up to 60.4 GPa. The compression properties and stress state are analyzed using lattice strain theory. Experiments were conducted at beamline X17C of the National Synchrotron Light Source. The radial x-ray diffraction data yield a bulk modulus that is qualitatively consistent with density functional theory calculations and demonstrate that WB is a highly incompressible material. A maximum differential stress, t, of about 14 GPa can be supported by nanocrystalline WB at the highest pressure. Thismore »« less
https://doi.org/10.1063/1.4728208

Similar Records

Title: Yield strength of Ni–Al–Cr superalloy under pressure

Abstract

Citation Formats

Physical metallurgy of nickel aluminides journal, February 2003

The effect of grain size on the yield strength of Ni3Al journal, September 1985

The yield strength of off-stoichiometric Ni3Al with and without boron journal, December 1991

Effect of B and Cr on elastic strength and crystal structure of Ni3Al alloys under high pressure journal, January 2015

Thermodynamic properties of Al, Ni, NiAl, and Ni3Al from first-principles calculations journal, May 2004

Shock-induced order-disorder transformation inNi3Al journal, January 2005

Static strength and equation of state of rhenium at ultra-high pressures journal, February 1991

Yield strength of MgO to 40 GPa journal, January 1988

Yield strength of the B1 and B2 phases of NaCl journal, January 1988

Effect of a Coordination Change on the Strength of Amorphous SiO2 journal, August 1988

The lattice strains in a specimen (cubic system) compressed nonhydrostatically in an opposed anvil device journal, May 1993

The lattice strains in a specimen (hexagonal system) compressed nonhydrostatically in an opposed anvil high pressure setup journal, May 1994

Yield strength at high pressure and temperature journal, May 1994

The strength of moissanite journal, July 2002

Elasticity and rheology of iron above 220 GPa and the nature of the Earth's inner core journal, December 1998

Elasticity, shear strength, and equation of state of molybdenum and gold from x-ray diffraction under nonhydrostatic compression to 24 GPa journal, December 1999

X-ray diffraction study of the static strength of tungsten to 69 GPa journal, April 2006

TEM and high-temperature X-ray diffractometric studies on the structural transformations in Ni3Al journal, September 1994

A beamline for high-pressure studies at the Advanced Light Source with a superconducting bending magnet as the source journal, August 2005

Equation of state and thermodynamic parameters of NaCl to 300 kbar in the high-temperature domain journal, January 1986

Finite Elastic Strain of Cubic Crystals journal, June 1947

The Compressibility of Media under Extreme Pressures journal, September 1944

Pressure distribution in the diamond anvil press and the shear strenght of fayalite journal, November 1977

Microstructures and mechanical properties of a directionally solidified NiAl–Mo eutectic alloy journal, January 2005

Physical metallurgy of nickel aluminides
journal, February 2003

The effect of grain size on the yield strength of Ni3Al
journal, September 1985

The yield strength of off-stoichiometric Ni3Al with and without boron
journal, December 1991

Effect of B and Cr on elastic strength and crystal structure of Ni3Al alloys under high pressure
journal, January 2015

Thermodynamic properties of Al, Ni, NiAl, and Ni3Al from first-principles calculations
journal, May 2004

Shock-induced order-disorder transformation inNi3Al
journal, January 2005

Static strength and equation of state of rhenium at ultra-high pressures
journal, February 1991

Yield strength of MgO to 40 GPa
journal, January 1988

Yield strength of the B1 and B2 phases of NaCl
journal, January 1988

Effect of a Coordination Change on the Strength of Amorphous SiO2
journal, August 1988

The lattice strains in a specimen (cubic system) compressed nonhydrostatically in an opposed anvil device
journal, May 1993

The lattice strains in a specimen (hexagonal system) compressed nonhydrostatically in an opposed anvil high pressure setup
journal, May 1994

Yield strength at high pressure and temperature
journal, May 1994

The strength of moissanite
journal, July 2002

Elasticity and rheology of iron above 220 GPa and the nature of the Earth's inner core
journal, December 1998

Elasticity, shear strength, and equation of state of molybdenum and gold from x-ray diffraction under nonhydrostatic compression to 24 GPa
journal, December 1999

X-ray diffraction study of the static strength of tungsten to $69 GPa$
journal, April 2006

TEM and high-temperature X-ray diffractometric studies on the structural transformations in Ni3Al
journal, September 1994

A beamline for high-pressure studies at the Advanced Light Source with a superconducting bending magnet as the source
journal, August 2005

Equation of state and thermodynamic parameters of NaCl to 300 kbar in the high-temperature domain
journal, January 1986

Finite Elastic Strain of Cubic Crystals
journal, June 1947

The Compressibility of Media under Extreme Pressures
journal, September 1944

Pressure distribution in the diamond anvil press and the shear strenght of fayalite
journal, November 1977

Microstructures and mechanical properties of a directionally solidified NiAl–Mo eutectic alloy
journal, January 2005