UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence B - Raw Data

Fingersh, Lee

doi:10.21947/1482203

Title: UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence B - Raw Data

Dataset
Other Related Research

Abstract

Sequences B, C, and D: Downwind Baseline (F), Downwind Low Pitch (F), Downwind High Pitch (F) This test sequence used a downwind, teetered turbine with a 3.4° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of ±180° were achieved at low wind speeds, and yaw angles of -20° to 10° were achieved for high wind speeds. The blade tip pitch was 3° for sequence B, 0° for sequence C, and 6° for sequence D. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected.

Authors:

Fingersh, Lee

Pacific Northwest National Laboratory

Publication Date:: Mon Nov 28 04:00:00 UTC 2022

Research Org.:: Atmosphere to Electrons (A2e) Data Archive and Portal, Pacific Northwest National Laboratory; PNNL

Sponsoring Org.:: USDOE Office of Energy Efficiency and Renewable Energy (EERE), Wind and Water Technologies Office (EE-4W)

Subject:: 17 WIND ENERGY

OSTI Identifier:: 1482203

DOI:: https://doi.org/10.21947/1482203

Citation Formats


                    Fingersh, Lee. UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence B - Raw Data.  United States: N. p., 2022. 
        Web.  doi:10.21947/1482203.

Copy to clipboard


                    Fingersh, Lee. UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence B - Raw Data.  United States.  doi:https://doi.org/10.21947/1482203

Copy to clipboard


                    Fingersh, Lee. 2022.  
"UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence B - Raw Data".  United States.  doi:https://doi.org/10.21947/1482203.  https://www.osti.gov/servlets/purl/1482203. Pub date:Mon Nov 28 04:00:00 UTC 2022

Copy to clipboard


                    
@article{osti_1482203,

  title        = {UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence B - Raw Data},

  author       = {Fingersh, Lee},

  abstractNote = {Sequences B, C, and D: Downwind Baseline (F), Downwind Low Pitch (F), Downwind High Pitch (F) This test sequence used a downwind, teetered turbine with a 3.4° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of ±180° were achieved at low wind speeds, and yaw angles of -20° to 10° were achieved for high wind speeds. The blade tip pitch was 3° for sequence B, 0° for sequence C, and 6° for sequence D. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected.},

  doi          = {10.21947/1482203},

  journal      = {},

  number       = ,

  volume       = ,

  place        = {United States},

  year         = {Mon Nov 28 04:00:00 UTC 2022},

  month        = {Mon Nov 28 04:00:00 UTC 2022}

}

Copy to clipboard

Dataset:

View Dataset

DOI: https://doi.org/10.21947/1482203

Save / Share:

Export Metadata

Save to My Library

Similar records in DOE Data Explorer and OSTI.GOV collections:

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence Q - Raw Data

Dataset Fingersh, Lee

Sequence Q: Dynamic Inflow (P) This sequence was designed to characterize the dynamic inflow variation using the five-hole probes that extend upwind of the leading edge of the blade. This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speeds ranged from 5 m/s to 15 m/s, and data were collected at a 0° yaw angle. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data filemore »« less
UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence W - Raw Data

Dataset Fingersh, Lee

Sequence W: Extended Blade (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 21 m/s, and the yaw angle was held at 0°. The blade pitch angle was 3°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measuredmore »« less
UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 5 - Raw Data

Dataset Fingersh, Lee

Sequence 5: Sweep Wind Speed (F,P) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed was ramped from 5 m/s to 25 m/s by the wind tunnel operator. This was repeated with a decreasing ramp. The yaw angle was maintained at 0°. The blade tip pitch was 3° or 6°. The rotor rotated at 72 RPM. Blade pressure and probe measurements were collected for both pitch angles. The five-hole probes were removed and the plugs were installed for another 3° pitch case. Plastic tape 0.03 mm thick was used to smooth the interfacemore »« less
UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence X - Raw Data

Dataset Fingersh, Lee

Sequence X: Elevated RPM (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 12 m/s, and yaw angles of ±30° were obtained. The blade pitch angle was 3°. The rotor rotated at 90 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm-thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values inmore »« less
UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence C - Raw Data

Dataset Fingersh, Lee

Sequences B, C, and D: Downwind Baseline (F), Downwind Low Pitch (F), Downwind High Pitch (F) This test sequence used a downwind, teetered turbine with a 3.4° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of ±180° were achieved at low wind speeds, and yaw angles of -20° to 10° were achieved for high wind speeds. The blade tip pitch was 3° for sequence B, 0° for sequence C, and 6° for sequence D. These three sequences were interleaved during testing because the pitch angle change was easily made by the turbine operator. Themore »« less

Similar Records