DOE Data Explorer title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence W - Raw Data

Abstract

Sequence W: Extended Blade (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 21 m/s, and the yaw angle was held at 0°. The blade pitch angle was 3°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pretensioned to 40,000 N. During postprocessing, the probe channels were set to read –99999.99. The standard tip blocks were replaced with blade extensions that created a 5.532-m radius rotor as shown in Appendix A. The extension used the S809 airfoil throughout, and the linear taper of the blade continued along the extension. Note that the blade radius was not changed during post-processing so the pressure tap locations are at the same radial location, but the reference to 30% represents 30% of 5.029 m, not 5.532 m.more » Throughout this report, references to the blade span are made for the 5.029-m radius, not the 5.532-m radius.« less

Authors:
Publication Date:
DOE Contract Number:  
67025F
Research Org.:
Pacific Northwest National Lab. (PNNL), Richland, WA (United States). Atmosphere to Electrons (A2e) Data Archive and Portal
Sponsoring Org.:
USDOE Office of Energy Efficiency and Renewable Energy (EERE), Wind and Water Technologies Office (EE-4W)
Subject:
17 Wind Energy
OSTI Identifier:
1481777
DOI:
https://doi.org/10.21947/1481777

Citation Formats

Fingersh, Lee. UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence W - Raw Data. United States: N. p., 2022. Web. doi:10.21947/1481777.
Fingersh, Lee. UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence W - Raw Data. United States. doi:https://doi.org/10.21947/1481777
Fingersh, Lee. 2022. "UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence W - Raw Data". United States. doi:https://doi.org/10.21947/1481777. https://www.osti.gov/servlets/purl/1481777. Pub date:Mon Nov 28 00:00:00 EST 2022
@article{osti_1481777,
title = {UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence W - Raw Data},
author = {Fingersh, Lee},
abstractNote = {Sequence W: Extended Blade (F) This test sequence used an upwind, rigid turbine with a 0° cone angle. The wind speed ranged from 5 m/s to 21 m/s, and the yaw angle was held at 0°. The blade pitch angle was 3°. The rotor rotated at 72 RPM. Blade pressure measurements were collected. The five-hole probes were removed and the plugs were installed. Plastic tape 0.03-mm thick was used to smooth the interface between the plugs and the blade. The teeter dampers were replaced with rigid links, and these two channels were flagged as not applicable by setting the measured values in the data file to –99999.99 Nm. The teeter link load cell was pretensioned to 40,000 N. During postprocessing, the probe channels were set to read –99999.99. The standard tip blocks were replaced with blade extensions that created a 5.532-m radius rotor as shown in Appendix A. The extension used the S809 airfoil throughout, and the linear taper of the blade continued along the extension. Note that the blade radius was not changed during post-processing so the pressure tap locations are at the same radial location, but the reference to 30% represents 30% of 5.029 m, not 5.532 m. Throughout this report, references to the blade span are made for the 5.029-m radius, not the 5.532-m radius.},
doi = {10.21947/1481777},
journal = {},
number = ,
volume = ,
place = {United States},
year = {Mon Nov 28 00:00:00 EST 2022},
month = {Mon Nov 28 00:00:00 EST 2022}
}