70 Search Results

High-voltage spinel LiNi_0.5Mn_1.5O₄ (LNMO) has attracted considerable attention as a cathode material for next-generation lithium-ion batteries due to its high operating voltage and intrinsically fast lithium-ion diffusion kinetics. However, the practical implementation of LNMO remains limited by its rapid capacity decay, primarily associated with bulk structural instability and parasitic interfacial reactions. To address these issues, we innovatively introduced calcium (Ca) as a dopant to enhance both the oxygen framework and surface stabilities of the LNMO crystal through gradient doping. Observations from the electronic microscopies, X-ray diffraction, and the elemental analysis confirmed that Ca is preferentially enriched at the particle surface,more » and a disordered crystal phase is preserved in the bulk in the gradient-doped LNMO cathodes. As cathodes in LIBs, the Ca gradient-doped (Ca gr) LNMO materials delivered formation capacities of ∼126−130 mAh/g and exhibited Coulombic efficiencies of 88−95%, which are consistently higher than those of the uniform-doped samples at the same doping level and undoped sample. Especially, the Ca gr 0.05 LNMO cathode demonstrated significantly improved rate capability with ∼113 mAh/g preserved at 10 C, while ∼92 mAh/g and ∼110 mAh/g for undoped and Ca uniform 0.05 LNMO, respectively, and excellent cycling stability, retaining ∼124.1 mAh/g (∼96.3% capacity retention) after 500 cycles. The analysis of cyclic voltammetry, differential capacity, and electrochemical impedance revealed that the excellent electrochemical performance is attributed to the structural and morphological advantages of gradient-doped LNMO cathodes with a disordered bulk structure for fast Li⁺ diffusion and a Ca-enriched surface for minimizing the Mn dissolution.« less

With the promises of low cost, high operating voltage, and excellent rate capability, the high-voltage spinel material with the formula of LiNi_0.5Mn_1.5O₄ (LNMO) has been considered as one of the most promising cathode materials for nextgeneration lithium-ion batteries (LIBs). However, the adoption of LNMO into practical LIBs is greatly hindered due to its rapid capacity decay associated with its bulk structural instability and interfacial side reactions. To address these issues, we proposed to use the cost-effective calcium (Ca) element as a dopant to stabilize the oxygen framework and surface of the LNMO crystal. The experimental results showed that, with moderatemore » Ca doping, the obtained cathode (Ca 0.05 LNMO) retained a specific capacity of ∼121 mAh/g (∼94.4% capacity retention) after 500 cycles at 0.5 C, compared to ∼73% for the baseline bare sample. Furthermore, the Ca 0.05 LNMO cathode retained ∼84% of its initial capacity, vs the baseline with ∼69%, after 150 cycles at the high temperature of 55 °C. The excellent battery performance of the moderately Ca-doped LNMO cathode is ascribed to its structural and kinetic advantages.« less

Flooding-induced oxygen deprivation (anoxia) is a challenge to plant survival, necessitating adaptive mechanisms for recovery. This study investigated elemental redistribution during anoxia recovery using time-series elemental imaging to show changes in nutrient distribution. Focusing on the role of Cation/H⁺ Exchangers (CAXs) in Arabidopsis thaliana, we show how mutants deficient in specific CAX transporters (cax1 and the cax1-4 quadruple mutant) respond to anoxia and metal stress. Mutants showed reduced lipid peroxidation and increased expression of flood-tolerance proteins during recovery. X-ray fluorescence microscopy and laser ablation–inductively coupled plasma mass spectrometry were used to show elemental redistribution over time. In wild-type plants (Col-0),more » post-anoxia elemental distribution resembled the elemental distribution of CAX mutants under normoxic conditions, suggesting that CAX-mediated elemental distribution before anoxia enables faster recovery post-anoxia, rather than affecting remobilization post-anoxia. Although CAX mutants had altered tolerance to excess manganese and copper, leaf metal distribution during metal stress was not altered. Here, these findings introduce the potential utility of time-series elemental imaging to show stress-response phenotypes and the importance of elemental distribution to recovery after anoxia. The novelty of this work lies in resolving spatial distribution patterns in a non-static system to gain insight into mechanisms of stress resilience in plants.« less

Grass-dominated ecosystems cover wide areas of the land surface yet have received far less attention from the Earth System Model (ESM) community. This limits model projections of ecosystem dynamics in response to global change and coupled vegetation–climate dynamics. We used the Functionally Assembled Terrestrial Ecosystem Simulator (FATES), a dynamic vegetation demography model, to determine ecosystem sensitivity to alternate, observed grass allometries and biophysical traits, and evaluated model performance in capturing California C₃ annual grasslands structure and fire regimes. Grass allometry, leaf physiology, plant phenology, and plant mortality all drove the seasonal variation in matter and energy exchange and fire dynamicsmore » in California annual grasslands. Allometry influenced grassland structure and function mainly through canopy architecture-mediated space and light competition instead of through carbon partitioning strategy. Regional variation in grassland annual burned area was driven by variation in ecosystem productivity. Our study advances the modeling of grassy ecosystems in ESMs by establishing the importance of grass allometry and plant phenology and mortality in driving C₃ annual grassland seasonal dynamics and fire regime. The calibrated annual grass allometry and biophysical traits presented can be applied in future studies to project climate–vegetation–fire feedbacks in annual grass-dominant ecosystems under global change.« less

In this work, we analyzed the effects of mineral scaling on the performance of a 3D interfacial solar evaporator, with a focus on the cations relevant to lithium recovery from brackish water. The field has been rapidly moving toward resource recovery applications from brines with higher cation concentrations. However, the potential complications caused by common minerals in these brines other than NaCl have been largely overlooked. Therefore, in this study, we thoroughly examined the effects of two common cations (calcium and magnesium) on the long-term solar evaporation performance of a 3D graphene oxide stalk. The 3D stalk can achieve anmore » evaporation flux as high as 17.8 kg m^–2 h^–1 under one-sun illumination, and accumulation of NaCl on the stalk surface has no impact. However, the presence of CaCl₂ and MgCl₂ significantly reduces the evaporative flux even in solutions lacking scale-forming anions. A close examination of scale formation during long-term evaporation experiments revealed that CaCl₂ and MgCl₂ tend to precipitate out within the stalk, thus blocking water transport through the stalk and significantly dropping the evaporation rates. These findings imply that research attention is needed to modify and optimize the internal water transport channels for 3D evaporators. Additionally, we emphasize the importance of testing realistic mixtures–including prominent divalent cations– and testing long-term operations in interfacial solar evaporation research and investigating approaches to mitigate the negative impacts of divalent cations.« less

Limestone (calcite, CaCO₃) is an abundant and cost-effective source of calcium oxide (CaO) for cement and lime production. However, the thermochemical decomposition of limestone (~800 °C, 1 bar) to produce lime (CaO) results in substantial carbon dioxide (CO_2(g)) emissions and energy use, i.e., ~1 tonne [t] of CO₂ and ~1.4 MWh per t of CaO produced. Here, we describe a new pathway to use CaCO₃ as a Ca source to make hydrated lime (portlandite, Ca(OH)₂) at ambient conditions (p, T) while nearly eliminating process CO_2(g) emissions (as low as 1.5 mol. % of the CO₂ in the precursor CaCO₃, equivalentmore » to 9 kg of CO_2(g) per t of Ca(OH)₂) within an aqueous flowelectrolysis/ pH-swing process that coproduces hydrogen (H_2(g)) and oxygen (O_2(g)). Because Ca(OH)₂ is a zero-carbon precursor for cement and lime production, this approach represents a significant advancement in the production of zero-carbon cement. The Zero CArbon Lime (ZeroCAL) process includes dissolution, separation/recovery, and electrolysis stages according to the following steps: (Step 1) chelator (e.g., ethylenediaminetetraacetic acid, EDTA)-promoted dissolution of CaCO₃ and complexation of Ca²⁺ under basic (>pH 9) conditions, (Step 2a) Ca enrichment and separation using nanofiltration (NF), which allows separation of the Ca-EDTA complex from the accompanying bicarbonate (HCO₃^–) species, (Step 2b) acidity-promoted decomplexation of Ca from EDTA, which allows near-complete chelator recovery and the formation of a Ca-enriched stream, and (Step 3) rapid precipitation of Ca(OH)₂ from the Ca-enriched stream using electrolytically produced alkalinity. These reactions can be conducted in a seawater matrix yielding coproducts including hydrochloric acid (HCl) and sodium bicarbonate (NaHCO₃), resulting from electrolysis and limestone dissolution, respectively. Careful analysis of the reaction stoichiometries and energy balances indicates that approximately 1.35 t of CaCO₃, 1.09 t of water, 0.79 t of sodium chloride (NaCl), and ~2 MWh of electrical energy are required to produce 1 t of Ca(OH)₂, with significant opportunity for process intensification. This approach has major implications for decarbonizing cement production within a paradigm that emphasizes the use of existing cement plants and electrification of industrial operations, while also creating approaches for alkalinity production that enable cost-effective and scalable CO₂ mineralization via Ca(OH)₂ carbonation.« less

In this study, optically generated molecular spin centers offer an attractive platform for room-temperature spintronic and quantum applications. The linear acene family of molecules are especially good candidates due to their efficient generation of highly polarized triplet excitons via singlet fission. However, the direct detection and manipulation of these spin centers in thin films via the electrical means desirable for ultimate microelectronic devices has proven challenging. In particular, highly oriented triplet features have previously been detected in crystalline anthracene but longer acenes reveal only doublet features in Electrically-Detected Magnetic Resonance (EDMR). In this work we present EDMR spectra of highlymore » oriented triplet excitons in pentacene for the first time, using a host-guest style device made of tetracene and pentacene. The guest acts as an energetic trap site, permitting the isolation and detection of molecular triplets at room temperature. Modeling of these results shows that the observed resonance features correspond to triplet sublevel transitions on isolated pentacene guest molecules. Rotation of the applied field confirms the tendency of the linear acenes to self-orient with the longest molecular axis perpendicular to the device substrate. Lastly, we find the disappearance of resonant triplet features in the neat acenes is not primarily due to the effects of exciton delocalization, but a broader mechanism of spin relaxation primarily influenced by exciton diffusivity.« less

Iron/chromium hydroxide coprecipitation controls the fate and transport of toxic chromium (Cr) in many natural and engineered systems. Organic coatings on soil and engineered surfaces are ubiquitous; however, mechanistic controls of these organic coatings over Fe/Cr hydroxide coprecipitation are poorly understood. Here, Fe/Cr hydroxide coprecipitation was conducted on model organic coatings of humic acid (HA), sodium alginate (SA), and bovine serum albumin (BSA). The organics bonded with SiO₂ through ligand exchange with carboxyl (-COOH), and the adsorbed amounts and pK(a) values of -COOH controlled surface charges of coatings. The adsorbed organic films also had different complexation capacities with Fe/Cr ionsmore » and Fe/Cr hydroxide particles, resulting in significant differences in both the amount (on HA > SA(-COOH) >> BSA(-NH₂)) and composition (Cr/Fe molar ratio: on BSA(-NH2) >> HA > SA(-COOH)) of heterogeneous precipitates. Negatively charged -COOH attracted more Fe ions and oligomers of hydrolyzed Fe/Cr species and subsequently promoted heterogeneous precipitation of Fe/Cr hydroxide nanoparticles. Organic coatings containing -NH₂ were positively charged at acidic pH because of the high pK(a) value of the functional group, limiting cation adsorption and formation of coprecipitates. Meanwhile, the higher local pH near the -NH₂ coatings promoted the formation of Cr(OH)₃. Finally, this study advances fundamental understanding of heterogeneous Fe/Cr hydroxide coprecipitation on organics, which is essential for successful Cr remediation and removal in both natural and engineered settings, as well as the synthesis of Cr-doped iron (oxy)hydroxides for material applications.« less

TRP channels are implicated in various diseases, but high structural similarity between them makes selective pharmacological modulation challenging. Here, we study the molecular mechanism underlying specific inhibition of the TRPM7 channel, which is essential for cancer cell proliferation, by the anticancer agent CCT128930 (CCT). Using cryo-EM, functional analysis, and MD simulations, we show that CCT binds to a vanilloid-like (VL) site, stabilizing TRPM7 in the closed non-conducting state. Similar to other allosteric inhibitors of TRPM7, NS8593 and VER155008, binding of CCT is accompanied by displacement of a lipid that resides in the VL site in the apo condition. Moreover, wemore » demonstrate the principal role of several residues in the VL site enabling CCT to inhibit TRPM7 without impacting the homologous TRPM6 channel. Hence, our results uncover the central role of the VL site for the selective interaction of TRPM7 with small molecules that can be explored in future drug design.« less

Soft materials are usually defined as materials made of mesoscopic entities, often self-organised, sensitive to thermal fluctuations and to weak perturbations. Archetypal examples are colloids, polymers, amphiphiles, liquid crystals, foams. The importance of soft materials in everyday commodity products, as well as in technological applications, is enormous, and controlling or improving their properties is the focus of many efforts. From a fundamental perspective, the possibility of manipulating soft material properties, by tuning interactions between constituents and by applying external perturbations, gives rise to an almost unlimited variety in physical properties. Together with the relative ease to observe and characterise them,more » this renders soft matter systems powerful model systems to investigate statistical physics phenomena, many of them relevant as well to hard condensed matter systems. Understanding the emerging properties from mesoscale constituents still poses enormous challenges, which have stimulated a wealth of new experimental approaches, including the synthesis of new systems with, e.g. tailored self-assembling properties, or novel experimental techniques in imaging, scattering or rheology. Theoretical and numerical methods, and coarse-grained models, have become central to predict physical properties of soft materials, while computational approaches that also use machine learning tools are playing a progressively major role in many investigations. This Roadmap intends to give a broad overview of recent and possible future activities in the field of soft materials, with experts covering various developments and challenges in material synthesis and characterisation, instrumental, simulation and theoretical methods as well as general concepts.« less