6 Search Results

NiFeO_x catalysts with single site Re dopants exhibit much higher active and stability toward electrochemical oxygen evolution reaction (OER) compared to traditional NiFeO_x catalysts. Nevertheless, the relationship between physicochemical properties of NiFeReO_x catalysts and the correlated performance toward OER is unclear, which hampers to enhance the OER performance further. Herein, we prepared a series of NiFeReO_x catalysts with different physicochemical properties by treating them at different temperatures (up to 350 °C) and then evaluated their performance toward OER. Here, the results show that heat treatment can convert all metal oxidation states to higher values as well as specific surface areas,more » which are believed to favor real active site generation and OER activity enhancement. A decrease in activity is observed with the temperature increase at the low current range, and the smallest overpotential of 248 mV at 10 mA cm⁻² is achieved with the pristine NiFeReO_x catalyst. In contrast, the heat-treated samples possess smaller Tafel slopes and lower charge transfer resistance likely due to enhanced intrinsic activity (from higher oxidation states) and conductivity, which facilitate the reaction kinetics and surpass the pristine sample at a large current density. Additionally, the sample treated at 350 °C exhibits a higher activity at 1000 mA cm⁻² (1.68 V vs. RHE compared to pristine sample of 1.92 V vs. RHE); however, it manifests a poorer stability compared to the pristine one due to the imbalance of reconstruction/transformations that occurred on the catalyst surface during OER operation. Our work unravels the relationship between physicochemical properties of NiFeReO_x catalysts and the correlated OER performance and provides valuable insights for designing NiFeReO_x catalysts with high activity and durability.« less

In any electrochemical device, the separator or membrane allows specific ions to transport but blocks electrons and other chemical species, enabling the electrochemical energy to be harvested. However, small amounts of undesired species are known to permeate through the membrane, reducing overall system efficiency and lifetime. An emerging concept called the “Selective Transport Layer” preferentially allows only protons to pass through but reduces the permeance of other species by a meaningful degree. Here, in this study, we demonstrate that a 60 nm thick graphene oxide composite layer can be very effective in reducing gas and ion permeation, even for amore » gas as small as H₂, while not noticeably increasing proton transport resistance. In electrode and membrane accelerated stability tests, we show that both electrode and membrane durability are improved by a factor of two. Microscopy and mathematic simulations confirm that the graphene oxide composite is effective in blocking transport of dissolved Pt²⁺. The improved durability and reduced H₂ fuel crossover are expected to substantially reduce initial and operating costs of the fuel cell system. How this technology may affect other membrane-based electrochemical devices is also discussed.« less

Anion exchange membrane water electrolyzers (AEMWEs) represent a promising technology for hydrogen production. The big advantage of the technology is that it allows for the use of platinum group metal-free (PGM-free) electrocatalysts at both electrodes, including catalysts for the hydrogen evolution reaction (HER) at the cathode. In addition to fulfilling the cost requirement, PGM-free HER catalysts need to meet the activity and durability targets of the AEMWEs. Here, in this work, we developed several carbon-supported, xerogel-derived nickel (Ni) HER electrocatalysts and evaluated the effect of various synthesis conditions, such as the type of carbon support, Ni-to-carbon ratio, and heat-treatment temperaturemore » and time, on their performance. Scanning transmission electron microscopy combined with energy-dispersive X-ray spectroscopy (STEM-EDS), X-ray diffraction spectroscopy (XRD), and X-ray photoelectron spectroscopy (XPS) revealed the formation of Ni nanoparticles with an oxygen-rich layer on the outside. Durability of the best-performing catalyst was assessed via a constant-current hold at 10 mA cm^–2 over 100 h. This catalyst was found to be more active and durable than the reference PGM-free material, a commercial Ni catalyst supported on a Vulcan XC-72. The catalyst was also tested in the cathode of a fully PGM-free AEMWE, allowing to reach 1.90 V (1.84 V HFR-free) at 1 A cm^–2 at 80 °C.« less

Quick and easy Ag catalysts preparation via wet chemical synthesis method using only reducing agent (pure-Ag); reducing agent and citric acid as the capping agent (Ag-CA); and carbon support (KetjenBlack 600J), capping agent, and the reducing agent (Ag/C) is demonstrated. The Ag-based electrocatalysts are characterized by high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) with energy-dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, and X-ray photoelectron spectroscopy (XPS). The electrocatalytic activity of Ag catalysts for O₂ reduction reaction (ORR) in 1 M KOH is evaluated using the rotating (ring)-disc electrode method. SEM and HAADF-STEM results showmore » that the unsupported pure-Ag and Ag-CA catalysts consist mainly of big agglomerates, and Ag/C has the smallest agglomerates and some sub-3 nm Ag nanoparticles. The XPS results reveal that Ag in all the catalysts is in the metallic form (Ag⁰). Despite consisting of big agglomerates, the Ag-CA catalyst exhibits similar ORR electrocatalytic activity to that of Ag/C. Ag-CA (unsupported) shows the lowest hydrogen peroxide yield. These results are of great importance for the development of Ag-based catalysts that can be prepared in a fast, simple and easily up scalable fashion, for anion exchange membrane fuel cells.« less

Obtaining high-quality 3D reconstructions from electron tomography of crystalline particles embedded in lighter support elements is crucial for various material systems such as catalysts for fuel cell applications. However, significant challenges arise due to the limited tilt range, sparse and low signal-to-noise ratio of the measurements. In addition, small metal particles can cause strong streaking and shading artifacts in the 3D reconstructions when using conventional reconstruction algorithms due to the presence of Bragg diffraction and the large scattering cross-section difference between the materials of the particles and the background support regions. These artifacts lead to errors in the downstream characterizationmore » affecting extraction of critical features such as the size of the metal particles, their distribution and the volume of the lighter support regions. In this paper, we present a two-stage algorithm based on metal artifact reduction, utilizing model-based iterative reconstruction methods with adaptive adjustment of regularization parameters. Our approach yields high-quality 3D reconstructions compared to traditional algorithms, accurately capturing both the metal particles as well as the background support. We demonstrate the effectiveness of our algorithm through simulated and experimental bright-field electron tomography data, showing significant improvements in reconstruction quality compared to traditional methods.« less

The loss of platinum (Pt) electrochemically active surface area (ECSA) is a critical degradation mode that often becomes a limiting factor for heavy-duty proton exchange membrane fuel cell vehicles. High surface area carbon supports have been shown to improve Pt dispersion and limit detrimental ionomer-electrocatalyst interactions due to their large interior pore volume. Here, in this work, using automated scanning transmission electron tomography, the degradation of nanoparticles located on the interior versus exterior surfaces of the carbon support is compared following a catalyst-specific accelerated stress test (AST) of 90,000 voltage cycles between 0.6 V to 0.95 V. The results reveal a notablemore » increase in median particle size for both interior and exterior Pt catalyst particles, with a slightly higher increase in particle size distribution and loss of specific surface area for the particles located on the exterior carbon surface. The fraction of Pt nanoparticles that reside within the interior of the carbon support also increased following the AST test, accompanied by evidence of an increase in average carbon mesopore size. Here, the results shed light on the degradation mechanisms affecting electrochemical properties and the enhanced particle accessibility at lower relative humidity.« less