32 Search Results

Laser Powder Bed Fusion (LPBF) has emerged as a promising route for fabricating intricate geometries in high-performance alloys. Haynes 282 (H282) is a strong candidate for applications such as heat exchangers or engines due to its excellent creep strength and thermal stability; however, the long-term creep behavior of LPBF-processed H282 remains poorly understood. In this study, the 𝜃-projection method is used to analyze and extrapolate the creep behavior of vertically built LPBF, horizontally built LPBF, compared to wrought H282 tested at 816 ◦C. Vertically built LPBF H282 exhibits the lowest minimum creep rate (MCR), while the horizontally built condition showsmore » a higher MCR comparable to that of wrought H282. Despite these differences, both LPBF conditions exhibit significantly shorter rupture life and reduced rupture strain than the wrought material, with the most severe degradation observed in the horizontal builds, consistent with an earlier onset of tertiary creep and accelerated strain-rate evolution. Microstructural characterization reveals that both LPBF and wrought H282 exhibit abundant twin-related boundary character; however, their grain boundary topologies differ markedly. The wrought alloy contains a higher fraction of low-angle grain boundaries and continuous twin lamellae, whereas the LPBF microstructure is characterized by a suppressed low-angle boundary population and fragmented twin-related boundaries embedded within irregular high-angle grain boundary networks. Fractographic analysis further reveals predominantly intergranular cracking in LPBF H282, accompanied by grain-boundary-decorated carbides, Al2O3 inclusions, and high-aspect-ratio pores. These results demonstrate that grain boundary topology, rather than minimum creep rate alone, plays a critical role in governing creep damage accumulation and rupture behavior in LPBF and wrought H282.« less

The creep-rupture behavior of weldments of alloy 740H fabricated using shielded metal arc welding with a commercially available filler metal based on alloy 263 and a post-weld heat treatment of 800 °C/4 h was studied at 650, 750, and 850 °C. Stress levels were chosen to reach extended rupture lifetimes (up to over 71,000 h) relevant for long-term applications and pressure vessels and piping code qualifications. All ruptures occurred within the weld zones of the cross-weld specimens except for one case at 850 °C for which the ruptured region covered both the weld and heat-affected zone. The effect of the welding process on creep lifetimemore » was quantitatively evaluated using weld strength reduction factors (WSRFs) which represented, for a given rupture time and temperature, the ratio of the applied creep-rupture stress of the weldment to that of alloy 740H base metal. These factors were 0.78-0.88, 0.82-0.89, and 0.64-0.75 at 650, 750 and 850 °C, respectively. Accordingly, with two exceptions at 850 °C with lower applied stresses, the creep failures were attributed to the lower strength of the weld zone relative to the alloy 740H base metal. Importantly, the failure location and WSRF depended on the microconstituents, microstructure, and stabilities of the weld and base metals at the creep temperatures, rather than welding-induced chemical inhomogeneities or defects. The weld strength reduction of these weldments was very similar to the expected ratio of creep-rupture strength of alloy 263 to that of alloy 740H.« less

This study explores the feasibility of fabricating cryogenic austenitic steel JK2LB via both laser-based directed energy deposition (laser-DED) and arc-based directed energy deposition (arc-DED) additive manufacturing processes for potential application in fusion reactors. JK2LB, a low-nickel, high-manganese stainless steel developed for ITER, offers excellent cryogenic toughness, radiation resistance, and decay-to-clearance characteristics. Although JK2LB was originally designed to endure cyclic stresses at cryogenic temperatures in tokamaks, its low-temperature mechanical integrity and radiation tolerance also make it a promising candidate for structural components, such as the coil case/support structure in nonplanar high-temperature superconducting magnet assemblies in stellarators. Directed energy deposition (DED) additivemore » manufacturing was selected for this study due to its capability to fabricate large structures with complex geometries. Here, to address the long lead time and high cost associated with acquiring conventional JK2LB solid wire, JK2LB powder-cored wire was developed as the feedstock material. Testing blocks were then fabricated using both wire-fed laser-DED and arc-DED processes. Microstructural and compositional analyses revealed that both DED approaches yield fully austenitic phase and columnar grain structures. Mechanical testing at room temperature revealed that both DED routes achieved yield strength and elongation comparable to those of conventionally processed JK2LB via vacuum melting, electroslag remelting, extrusion, and drawing, though ultimate tensile strength was reduced due to Mn loss and large columnar grains. As a study mainly focusing on the additive manufacturing process, this work demonstrates the potential of additive manufacturing for fusion energy applications and provides a basis for optimization and future cryogenic mechanical evaluation.« less

The V-4Cr-4Ti (V44) alloys have been proposed as the prime candidate structural material for self-cooled liquid Li blanket and other designs for fusion energy applications. However, the applications of the V44 alloy are limited to a narrow operation temperature window, due to reduction in creep strength at or above 700 °C and susceptibility to irradiation hardening and embrittlement when irradiated below 400 °C. Here, in this work, we explore the feasibility of designing a novel V alloy to form a high number density of TiC nanoprecipitates, in order to simultaneously improve creep strength and provide defect sinks to mitigate irradiationmore » hardening. Computational thermodynamics was used to design a new alloy (V44C) to achieve our goal of high TiC nanoprecipitates density within the alloy V44 matrix. To ensure scalability, the new alloy was made through arc-melting and ingot-casting followed by hot forging, cold rolling and heat treatments of homogenization and precipitation aging. The microstructure was characterized by SEM, TEM, XRD and APT, confirming the existence of nanoprecipitates predicted in the thermodynamic calculations. In addition to microstructural evaluation tensile properties at room temperature and 700 °C, and Charpy impact energy at room temperature were measured. The microstructure and mechanical properties were then compared with those from a historic reference V44 alloy. The tensile strength improvement in V44C was rationalized based on particle and solid solution strengthening mechanism. The fracture behavior was discussed based on the fractography results and necking deformation behavior.« less

Ferritic-martensitic steels are promising structural materials for advanced nuclear reactors. To minimize long-term radioactivity, reduced-activation ferritic-martensitic steels have been developed by substituting high-activation elements like Ni and Mo with low-activation elements such as W. However, the impact of these alloying modifications on helium bubble formation, which plays a key role in material swelling, remains unclear. Here, in this study, we compared helium bubble formation in ferritic-martensitic steel T91 and reduced-activation ferritic-martensitic steel F82H. Both materials were irradiated with sequential 100 keV, 150 keV, and 200 keV helium ions to a dose of 0.5 dpa and a helium concentration of 9,000more » appm at 500°C. The helium bubbles in F82H exhibited a larger average size and a lower density than those in T91, suggesting differences in minor alloying elements may influence the bubble growth. Here, to investigate the effects of these alloying elements, we characterized radiation-induced segregation near bubbles and grain boundaries. Prominent Ni-Mn-Si enriched clusters were found near bubbles in T91, while only Mn-Si enriched clusters were found near bubbles in F82H. In addition, the obvious Cr enrichment near grain boundaries was absent around bubbles in both steels. The different segregation trends among elements revealed the variations in element diffusion mechanisms and the different sink biases between bubbles and grain boundaries. Cr enrichment near grain boundaries is mostly driven by interstitial-mediated diffusion. However, since bubble growth relies on net vacancy flux, vacancy-mediated diffusion plays a dominant role in controlling element segregation near bubbles. Therefore, Cr enrichment was not found near bubbles. Because of preferential vacancy-drag diffusion for Ni, Si and Mn, these elements were enriched near bubbles. Due to the strong binding energies of vacancies with these solute atoms, the vacancy diffusivity can be reduced near these solutes. Therefore, the more prominent Ni-Si-Mn clustered near helium bubbles in T91 lead to stronger suppression of helium bubble growth compared to F82H.« less

Reactor core internal components such as baffle-former bolts (BFBs) are subjected to significant mechanical stress, corrosive environment, and neutron irradiation from the reactor core during the plant operation. Over the long operation period, these conditions lead to potential degradation and of the bolts. In this work, characterization was performed on the oxidized surface of stainless steel BFBs harvested from a commercial pressurized water reactor (PWR) after 40 years of operation. The analysis shows that a complex multilayered surface oxide with six identified layers formed that is different from 2-layer structure commonly observed in model experiments. The oxide varies by compositionmore » – predominantly Fe, Cr, and Ni, grain size, and phase, and has features resembling both unirradiated and radiation/ corrosion experiments likely due to the low radiation flux compared to ion-irradiation or the test reactor radiation. In addition, grain boundary oxidative attack featured a pathway for Fe and other elements to move from the metal matrix to the outermost oxide. In conclusion, the results help assess PWR lifetime extension, put into context previous experimental studies, and provide input for designing experiments combining radiation and corrosion effects.« less

The decommissioning of the Zion Nuclear Power Plant (NPP) provided a unique opportunity to harvest and study service-aged reactor pressure vessel (RPV) beltline materials. This work, conducted through the U.S. Department of Energy’s Light Water Reactor Sustainability (LWRS) Program, aims to improve the understanding of radiation-induced embrittlement to support extended nuclear plant operations. Material segments containing the Linde 80 flux, wire heat 72105 (WF-70) beltline weld and the A533B Heat B7835-1 base metal, obtained from the intermediate shell region with a peak fluence of 0.7 × 10¹⁹ n/cm² (E > 1.0 MeV), were extracted, cut into blocks, and machined intomore » test specimens for mechanical and microstructural characterization. The segmentation process involved oxy-propane torch-cutting, followed by precision machining using wire saws and electrical discharge machining (EDM). A chemical composition analysis confirmed the expected variations in alloying elements, with copper levels being notably higher in the weld metal. The harvested specimens enable a detailed evaluation of through-wall embrittlement gradients, a comparison with the existing surveillance data, and the validation of predictive embrittlement models. This study provides critical data for assessing long-term reactor vessel integrity, informing aging-management strategies, and supporting regulatory decisions to extend the life of nuclear plants. This article is a revised and expanded version of a paper entitled, “Current Status of the Characterization of RPV Materials Harvested from the Decommissioned Zion Unit 1 Nuclear Power Plant”, PVP2017-65090, which was accepted and presented at the ASME 2017 Pressure Vessels and Piping Conference, Waikoloa, HI, USA, 16–20 July 2017.« less

Ferritic-Martensitic steel welds typically require post weld heat treatment (PWHT) to restore toughness and high temperature performance. This off-line thermal process reduces disparities between weld and base metal, but can cause distortion, cracking, or simply be impractical due to assembly size and joint non-uniformity. Here we show integrated welding and thermal processing applied to modified 9Cr-1Mo (Grade 91) steel, favored for advanced power generation applications, performed in real time through the addition of a secondary heat source near the primary weld head. Optimal integrated processing reduces weld fusion and heat affected zone hardness by 125 HV, approaching performance of conventionalmore » 730 °C, 60 min PWHT processing. Microstructures and mechanical performance are compared for mechanized GTAW welds, with equivalent lifetimes noted in cross-weld creep rupture tests up to 234 MPa at 550 °C, and up to 104 MPa at 650 °C. The integrated process was validated on a Grade 91 pressure vessel with multipass cold wire feed GTAW. After 550 °C, 71.4 bar thermomechanical cyclic testing, the maximum weld hardness is <350 HV.« less

The deterministic approach widely adopted in the design of structural components relies on systematically defined design limits using empirically determined safety factors. However, this approach is not always appropriate because structures are subjected to a variety of loads in the practical environment, which may result in excessively conservative design limits. In recent years, a more rigorous probabilistic approach that incorporates material strength distributions has become an important solution. In the probabilistic approach, the probability density functions of material strength properties underpin the design criteria. Here, the objective of this study is to identify the density distribution functions that best describemore » tensile properties of irradiated F82H to define a reference strength for DEMO design. Due to the limited number of existing data, this study specifically employs a Bayesian prediction method based on Monte Carlo simulations to determine a material reference value with statistical reliability and to investigate its effectiveness. For example, the dependence of tensile properties of 300 °C irradiated materials on irradiation damage and the range predicted by 95% Bayesian estimation was evaluated. As a statistical model for the dose dependence of statistical parameters, the normal distribution exhibited a better fit for 0.2% proof strength and tensile strength, whereas the distribution of total elongation data gave comparable reference values for both the normal and Weibull distribution models. Both models gave comparable criteria for the distribution of total elongation data. The Weibull model also gave better results for uniform elongation. The function best describing the model was a logarithmic law for both 0.2% proof strength and tensile strength, while a power law for both total and uniform elongation, which allowed for more comprehensive data prediction of irradiation data with statistical accuracy for DEMO reactor design.« less

Here, post-irradiation evaluation was performed on a 316 stainless steel baffle former bolt harvested after 40 years of service in a pressurized water reactor. Microstructure analysis revealed the presence of defect-free dislocation channels and strain-induced twins, indicative of loading at a stress level close to yield stress at least once while in service. Primary radiation-induced Ni/Si precipitates were destroyed during channel and twin formation, and secondary, significantly coarser Ni/Si precipitates formed along newly formed Σ3 boundaries during the continued irradiation. Additionally, an elevated phosphorus level was observed inside the strain-induced twin. Complex chemistry inside the strain-induced feature may overlap withmore » dislocation pileups and impact localized corrosion, material long-term performance, and safety.« less