63 Search Results

It has been recently demonstrated that eutectic alloys processed by additive manufacturing have excellent high-temperature mechanical properties. We suggest that nickel-base eutectic alloys may enable new combinations of structural and functional properties. To this end, we investigate the processability, microstructure, and thermal stability of five, binary near-eutectic Ni-X (X = B, Ce, La, Y, and Zr) alloys processed via surface laser-remelting. The microstructure of all alloys contain a two-phase lamellar eutectic microstructure consisting of γ-Ni and intermetallic phases; this microstructure is significantly finer (100–200 nm lamellar spacing) in the laser-remelted alloys than in the cast substrate (0.5–1.0 µm lamellar spacing). The microhardness of themore » laser-remelted alloys (550–770 HV) is 35–50% higher than that of the cast alloys (370–570 HV) due to this finer eutectic spacing. An anomalous eutectic microstructure appears at the meltpool boundaries, containing globular and lamellar γ-Ni phases. The alloys contain a high volume fraction (>50 vol%) of intermetallic phase which forms a continuous network, causing brittleness. Following laser-remelting trials, the alloys showed a high density of solid-state cracks, except for the Ni-Zr alloy which processed well. During thermal exposure at 700 and 900°C for up to 500 h, the eutectic microstructure coarsens. Coarsening occurs heterogeneously and initiates at the meltpool boundaries. This process occurs more slowly in the Ni-Zr and Ni-Y alloys, and more rapidly in the remaining alloys, resulting in greater microhardness retention in the Ni-Zr and Ni-Y alloys following thermal exposure at 700°C. Thus, among the five alloys, the Ni-Zr system exhibits a good combination of high-temperature mechanical properties and processability. We conclude with recommendations for future work on designing additively manufactured alloys based on these eutectic Ni systems.« less

As-solidified microstructures of near-eutectic alloys often contain multiple primary phases that are not expected from equilibrium phase diagrams. Such microstructures are caused by cooling-rate-dependent solidification pathways, a factor not captured by the Scheil–Gulliver model or variations thereof. Here, we present a model and algorithm that incorporate the critical nucleation undercooling for each solid phase into the Scheil–Gulliver model. We hypothesize that the non-equilibrium microstructure formation is primarily governed by a nucleation-competition mechanism. This mechanism accounts for both stable/metastable phase selection and primary-phase formation within eutectic regions driven by asymmetric nucleation barriers. The model is validated against a hypereutectic Al-Fe alloy,more » where it successfully reproduces the observed microstructural constituents, revealing the key dependencies of solidification microstructure on nucleation kinetics. Applicability to multicomponent systems is demonstrated through a hypereutectic Al–Fe–Si ternary alloy, where the model successfully predicts divorced eutectic microstructures and the associated oscillatory solidification pathways along univariant lines. The proposed framework establishes a nucleation-dependent computational approach for interpreting and predicting solidification microstructures.« less

The high cycle fatigue behavior of laser powder bed fusion processed AlSi10Mg has been investigated at 350 °C (T/T_m ∼ 0.7). The alloy exhibited a fatigue strength of 30 MPa defined by runout after 10⁷ cycles at a conventional loading frequency of 20 Hz, corresponding to a notable fatigue strength to ultimate tensile strength ratio of 0.73. The surprising fatigue resistance was attributed to the strain-rate hardening effect at high fatigue loading frequency relative to tensile loading rates at 350 °C. The strain-rate hardening effect was validated by performing ultrasonic fatigue tests (20 kHz loading frequency) with three orders ofmore » magnitude higher strain-rates than those at conventional loading frequency. The higher strain-rates in ultrasonic fatigue increased the magnitude of strain-rate hardening resulting in longer AlSi10Mg fatigue lives compared to fatigue at conventional frequency, thus confirming the strain-rate hardening effect. The fatigue crack initiation mechanism was strain-rate dependent. Post-mortem microstructural examination revealed intergranular cavitation inside clusters of fine equiaxed grains. The cavities interlinked with each other to initiate near-surface fatigue cracks at conventional frequency. Cavitation occurred to a lesser extent at the ultrasonic frequency. As a result, fatigue cracks initiated at pre-existing processing defects near the surface in ultrasonic fatigue samples. Finally, this investigation underscores the role of fine grain clusters in promoting high-temperature fatigue crack initiation and indicates a possible trade-off between printability via grain refinement and high-temperature fatigue resistance of additively manufactured alloys.« less

Here, a new, solute-lean Al-0.3Zr-0.2Ce-0.2Cu (wt.%) alloy is developed for additive manufacturing that overcomes the classical tradeoff between conductivity and creep resistance. The rapid-cooling-enabled supersaturation of Zr, and its uniform distribution in α-Al matrix, along with formation of submicron (Ce,Cu)-rich intermetallic particles on solidification lead to unusually high creep resistance at 200 °C. Near-zero secondary creep rates are achieved up to the alloy yield stress (YS) of 65 MPa at 200 °C in as-fabricated state. The Zr-solute-induced dislocation-climb suppression mechanism underlying this improvement also restricts dynamic recovery above YS, as noted from appreciable primary creep and its transitioning to near-zeromore » secondary creep rates. A combination of relatively coarse, epitaxially-grown α-Al grains, low Zr concentration in α-Al, and the impurity-scavenging effect of Ce to purify α-Al matrix produces high electrical conductivity of ∼48 %IACS. Aging precipitation of L1₂-Al₃Zr nanoprecipitates doubles the YS (to ∼150 MPa) at room temperature and increases alloy conductivity to ∼58 %IACS, but loss of solid-solution Zr out of α-Al matrix leads to activation of dislocation climb, degrading the creep properties as compared to the supersaturated Al-Zr solid solution in the as-fabricated state. Compared to L1₂-Al₃Zr nanoprecipitates, submicron (Ce,Cu)-rich particles formed on solidification are more effective at impeding dislocation climb, producing a threshold stress for dislocation creep of ∼ 50 MPa at 200 °C. The new alloy design concepts, especially solute-induced dislocation-climb suppression for creep resistance, explored here may pave way for the design of new metallic alloys for thermal/electrical conductors and other high-temperature applications.« less

There is a current need for new aluminum alloy design strategies to target applications requiring high strength and conductivity with reductions in mass. A new lightweight Al-2Ni-0.5Zr (wt. %) conductor alloy was fabricated using laser powder bed fusion. A design of experiments probed the alloy's solidification cracking susceptibility. It was observed that solidification cracking was generally reduced with fast scan speeds, above 1500 mm/s, and smaller hatch spacings. The different cooling rates throughout the melt pool produced a heterogeneous distribution of cellular and equiaxed Al₃Ni precipitates in the as-printed alloy. Additionally, the rapid solidification characteristic of laser powder bed fusionmore » created a super-saturated Zr solid solution. An aging heat treatment at 375 °C for 24 h imparted strengthening through the precipitation of L1₂-Al₃Zr nanoprecipitates, which counteracted the softening caused by the fragmentation and coarsening of Al₃Ni precipitates. The yield strength increased from 138 MPa in the as-printed condition to 168 MPa after aging, while the ductility remained constant at ∼21%. The aging treatment simultaneously increased the electrical conductivity from 40.8% IACS (International Annealed Copper Standard) to 53.5% IACS. Modeling of the strengthening mechanisms and electrical conductivity contributions rationalized the simultaneous increase in strength and conductivity upon aging. Furthermore, the strengthening efficacy of the Al₃Ni and L1₂-Al₃Zr precipitates, combined with the low Ni and Zr solubility in the FCC Al matrix, facilitated both high strength and electrical conductivity. Overall, the combination of strength and electrical conductivity positions this alloy as a suitable choice for additively manufactured lightweight conductors.« less

Tensile creep response and cavitation damage evolution in an additively manufactured Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt%) alloy with peak-aging and overaging treatments were investigated in the 300–400 ºC range. Microstructural heterogeneity and its response to heat treatment and subsequent creep deformation were studied to understand the interplay between cavity formation, creep lifetime and ductility. Increasing the applied stress activated the nucleation of more cavities, an experimental observation that is well described using the vacancy accumulation model. Cavities nucleated prematurely due to localized plasticity in the denuded zones that formed at/near melt-pool or grain boundaries. Microstructure/deformation heterogeneity with consequent evolution of stress triaxiality, especiallymore » at lower stresses, causes accelerated cavitation, thus producing low creep ductility (∼ 0.2–2.4 %), compared to (∼12–21 %) ductility of the alloy measured by regular tensile tests at equivalent temperatures. A constrained diffusional cavity growth mechanism with continuous cavity nucleation during creep is established as the dominant mechanism, implying that cavitation involves vacancy diffusion, yet its growth rate is dictated by the minimum creep rate. In conclusion, the ductility-limiting creep and cavitation mechanisms discussed here provide new insight into the creep behavior of 3D-printed metallic alloys.« less

While L1₂-Al₃Zr nanoprecipitates provide a balance between strengthening and good electrical conductivity, the precipitation of L1₂-Al₃Zr in aluminum requires aggressive heat treatments. An improved age-hardening response was observed during isochronal aging of an Al-0.24Zr (wt%) alloy when microalloyed with Sn. A new mechanism termed Low melting point Element-Assisted Nucleation (LEAN) is proposed to explain the lower temperature nucleation of L1₂-Al₃Zr precipitates observed in this alloy based on the addition of a low melting point element, such as Sn. Characterization verified the first-principles density functional theory prediction that Zr and Sn atoms cluster during homogenization owing to the favorable binding energymore » of Zr-Sn-vacancy triplets. Direct microstructural observations revealed these clusters form Sn nanoprecipitates that assist the nucleation of L1₂-Al₃Zr at 200°C, where L1₂-Al₃Zr precipitation is not expected due to the low diffusivity of Zr atoms in Al. At higher temperatures (≳350°C), the acceleration of L1₂-Al₃Zr precipitation is driven by faster Zr diffusion in Al with Sn microalloying and the nuclei formed via the LEAN mechanism. In conclusion, this combination of mechanisms explains the improvement in age hardening through L1₂-Al₃Zr precipitation with Sn microalloying.« less

Droplet-on-demand liquid metal jetting (DOD-LMJ) is a new method for additive manufacturing of bulk structural alloys. Here, we report on the microstructure, tensile, and fatigue properties of an Al-7Si-0.4Mg (A356) alloy fabricated with LMJ. Liquid metal droplets were shielded by high-purity Ar gas shroud during deposition. Atom probe tomography revealed that a few nanometers thick (Al-Mg-Si)-O oxide film formed on the droplets despite Ar gas shielding. Tensile tests on peak-aged LMJ A356 alloy showed that yield strength was isotropic (250 MPa), but ductility was lower in the build direction (6.1 ± 1.4 %) compared to the transverse direction (9.4 ± 1.0 %). Lower ductility in the buildmore » direction was attributed to delamination of metal-oxide interfaces at layer boundaries. The ductility and yield strength of LMJ A356 were similar to cast A356 and laser powder bed fused (LPBF) A357 alloys, indicating the limited impact of oxide film on tensile properties. The oxide film severely impacted the fatigue properties. Fatigue resistance of LMJ A356 was limited by fatigue crack initiation at lack-of-fusion defects and fatigue crack propagation along layer boundaries by delamination of the metal-oxide interface. The fatigue strength of LMJ A356 at 60 MPa was lower than cast A356 and LPBF A357 alloys in the peak-aged condition. This research underscores the need for managing droplet oxidation during LMJ additive manufacturing of structural alloys.« less

Additively manufactured (AM) metal-metal composites consisting of PrintCasted 316 L austenitic stainless-steel lattice structures infiltrated with A356 casting alloy, have recently been developed for use in high energy absorption systems with potential applications ranging from static load bearing to dynamic blast containment structures. This system has a unique mechanical behavior as the volume fraction of lattice increases showing a transition from localized to de-localized failure and dramatic increase in energy absorption capability. In this work, PrintCast A356/316 L composite tensile specimens were produced with lattice volume fractions ranging from 20 % to 50 % to capture the range of thismore » behavior. Finite element simulations support neutron diffraction measurements of stress state. Results illustrate that in tension, the reinforcement material is in tension while the matrix support material is in compression, information offering significant insight into the transition to de-localized failure. Moreover, the simulation results provide further insight into how interfacial bonding (or lack of bonding) affects the energy absorption capabilities of the PrintCast composites.« less

Electric vehicle brake rotors demand lightweight, high thermal conductivity materials with good resistance to wear, creep, salt corrosion, and thermal fade, all of which present challenges to the traditionally used cast iron. In this work, we investigated the braking performance of recently developed high-temperature aluminum alloys in both cast and 3D printed forms, that possess excellent microstructural and mechanical stability at elevated temperatures. Three aluminum alloys, Al-6Cu-Mn-Zr, Al-9Cu-Mn-Zr, and Al-Ce-Ni-Mn-Zr and a reference cast iron were tested on a sub-scale brake tester against a commercial brake pad material over a range of sliding speeds between 2 and 15 m/s. Themore » performance of these alloys was evaluated for wear resistance, friction behavior, temperature elevation, and surface morphological change. Although all three candidate alloys had lower wear-resistance than cast iron, Al-Ce-Ni-Mn-Zr showed a significantly reduced wear rate in comparison to the Al-Cu-Mn-Zr alloys. Moreover, Al-Ce-Ni-Mn-Zr alloy had the most consistent friction behavior at all sliding speeds and good fade resistance, as the coefficient of friction did not dramatically decrease with temperature rise but stayed within a desirable range of 0.35–0.50 instead. The superior wear resistance and braking performance of the Al-Ce-Ni-Mn-Zr alloy were attributed to its higher hardness, and high temperature yield strength and creep resistance compared with the Al-Cu-Mn-Zr alloys. In conclusion, the results suggest that the braking performance of these aluminum alloys could be further enhanced by increasing the hardness and forming a more stable transfer layer on the sliding surface.« less