18 Search Results

Single-site copper-based catalysts have shown remarkable activity and selectivity for a variety of reactions. However, deactivation by sintering in high-temperature reducing environments remains a challenge and often limits their use due to irreversible structural changes to the catalyst. Here, we report zeolite-based copper catalysts in which copper oxide agglomerates formed after reaction can be repeatedly redispersed back to single sites using an oxidative treatment in air at 550 °C. Under different environments, single-site copper in Cu–Zn–Y/deAlBeta undergoes dynamic changes in structure and oxidation state that can be tuned to promote the formation of key active sites while minimizing deactivation throughmore » Cu sintering. For example, single-site Cu²⁺ reduces to Cu¹⁺ after catalyst pretreatment (270 °C, 101 kPa H₂) and further to Cu0 nanoparticles under reaction conditions (270–350 °C, 7 kPa EtOH, 94 kPa H₂) or accelerated aging (400–450 °C, 101 kPa H₂). After regeneration at 550 °C in air, agglomerated CuO was dispersed back to single sites in the presence and absence of Zn and Y, which was verified by imaging, in situ spectroscopy, and catalytic rate measurements. Ab initio molecular dynamics simulations show that solvation of CuO monomers by water facilitates their transport through the zeolite pore, and condensation of the CuO monomer with a fully protonated silanol nest entraps copper and reforms the single-site structure. Importantly, the capability of silanol nests to trap and stabilize copper single sites under oxidizing conditions could extend the use of single-site copper catalysts to a wider variety of reactions and allows for a simple regeneration strategy for copper single-site catalysts.« less

Boron-based catalysts have been shown to be both active and selective for driving the oxidative dehydrogenation of propane (ODHP) without the use of precious metals. This reaction occurs at temperatures that melt the oxide catalyst which challenges our ability to identify the liquid structures of the boron oxide phase under reaction conditions, hindering the understanding of its active sites and reaction mechanism. By combining ab initio molecular dynamics simulation, in-situ Raman characterization, and microkinetic modeling, we propose that the di-coordinated boron sites (BO2) in liquid boron oxide are the active species for O2 activation under reaction conditions. The formed peroxy-likemore » species (>B-O-O-B<) can be viewed as a moderate oxidant for ODHP. The dynamical >B-O* dangling bond originated from >B-O-O-B< site as well as the liquid B2O3 structure itself, plays a critical role in the abstraction of H atoms from propane (C3H7 radical formation). Microkinetic modeling reveals C3H7 radical formation to be the main rate controlling step (~75% degree of rate control) with the dehydration of boron hydroxyls (B-OHs) to recover the di-coordinated boron active sites controlling the remainder of the rate (~25% degree of rate control). Moreover, the activation barriers are found to strongly depend upon the surface B-OH concentration. These findings provide significant insights into the active site and reaction mechanisms on boron-based catalysts for ODHP and underlie the importance of understanding the liquid nature of the catalyst to account for the catalytic activity.« less

Understanding the adsorption and reactivity of carboxylic acids on oxide surfaces is of great interest in catalysis for biomass upgrading via ketonization, a carbon–carbon coupling reaction. Herein, we investigate the adsorption and reaction of acetic acid on anatase TiO₂(101) using scanning tunneling microscopy, infrared spectroscopy, temperature programmed reaction, and density functional theory calculations. We demonstrate the adsorption of acetic acid can form two intermediates: (1) dissociated, bidentate acetate with an associated bridging hydroxyl, and (2) molecular, monodentate acetic acid. The coexistence of ordered phases with increasing monolayer (ML) saturation coverages consisting of (1) pure acetate (0.5 ML), (2) mixed acetate/aceticmore » acid (0.67 ML), (3) mixed acetate/acetic acid (1.0 ML) and (4) pure acetic acid demonstrates similar energetics for both acetate and acetic acid species. Under ultra-high vacuum conditions, the presence of both monodentate acetic acid and bidentate acetate was observed below room temperature, while solely bidentate acetate was observed up to 575 K. The deprotonation of acetic acid produces water at 280 K, while the thermal decomposition of bidentate acetate produces ketene and acetic acid at 645 K. In conclusion, this model study provides detailed insight into the stability and reactivity of carboxylic acid surface-bound intermediates, which could participate during ketonization reactions for biomass upgrading.« less

With airlines committed to drastically reduce their carbon footprint by 2050, producing jet fuel from renewable ethanol is of particular interest. Here we reported on an Ag/ZrO₂/SBA-16 catalyst that is very effective for directly converting ethanol into to n-butene-rich olefins jet fuel precursors (i.e., 88% at full conversion). Here, we report on a Cu/ZrO₂/SBA-16 catalyst that presents remarkable olefins selectivity (i.e., 89% at 96% conversion) and enhanced stability as compared to Ag/ZrO2/SBA-16 catalyst. Under severe operating conditions a conversion loss < 10% was observed with the Cu/ZrO₂/SBA-16 catalyst as compared to a 50% loss of conversion with the Ag/ZrO₂/SBA-16 catalyst.more » Combined experimental and computational tools revealed that replacing Ag with Cu shifts the reaction pathway of crotonaldehyde hydrogenation from 1,3-butadiene (i.e., coke precursor) production to butyraldehyde formation. Experiments conducted with 4%Cu/4%ZrO₂ supported on SBA-16, dealuminated zeolite Beta, and aluminum silicate revealed the performance and stability advantage of the SBA-16-supported catalyst.« less

The dynamics of reactive intermediates are important in catalysis for understanding transient species, which can drive reactivity and the transport of species to reaction centers. In particular, the interplay between surface-bound carboxylic acids and carboxylates is important for numerous chemical transformations, including CO₂ hydrogenation and ketonization. Here, we investigate the dynamics of acetic acid on anatase TiO₂(101) using scanning tunneling microscopy experiments and density functional theory calculations. We demonstrate the concomitant diffusion of bidentate acetate and a bridging hydroxyl and provide evidence for the transient formation of molecular monodentate acetic acid. The diffusion rate is strongly dependent on the positionmore » of hydroxyl and adjacent acetate(s). A facile three-step diffusion process is proposed consisting of acetate and hydroxyl recombination, acetic acid rotation, and acetic acid dissociation. Here this study clearly demonstrates that the dynamics of bidentate acetate could be important in forming monodentate species, which are proposed to drive selective ketonization.« less

Requiring catalysts to be both active yet stable over long periods of time under variable reaction conditions including high and low temperatures is a daunting challenge due to the almost mutual exclusivity of these constraints. Using CO oxidation as a probe reaction, in this work we demonstrate that thermally stable single atom copper catalysts prepared by high temperature synthesis (atom trapping) on ceria can achieve this feat by allowing modulation of the Cu charge state through facile charge transfer between active site and support. This provides the catalysts with an ability to activate either lattice or adatom oxygen atoms, accessingmore » additional reaction channels depending on the reaction conditions. Such adaptability allows dynamic response of catalysts enabling them to remain active under variable reaction conditions. The inherent stability of the catalyst arises from the enhanced strength of the Cu-O interactions from high temperature synthesis that exist even when Cu oxidation state varies, which retards sintering and deactivation. As we show here, one can circumvent the dilemma of designing catalysts that are simultaneously active and stable by matching the redox properties of the active site and support and establishing an environmental adaptability around the active sites.« less

The promise of lattice gas (LG) cluster expansions (CEs) is that they can describe a given system property to any level of accuracy since the orthogonal “cluster basis functions” span the complete space of available configurations. Such an approach can be constructed to an arbitrarily large surface of a finite number of distinct adsorption sites. Unfortunately, this is only true for the case of an ideal, fixed lattice decorated with components at precise lattice points (the lattice “sites”) with no distortions or relaxations subsequently allowed. Since most systems, and surfaces specifically, do not conform to such an ideal set ofmore » constraints, errors in LG CEs must be expected or CE convergence severely hampered. Beyond this, numerical errors in the provided data can complicate the proper construction of a truly predictive and/or physically significant CE. In this work, we show here how reliance on typical statistical tools like confidence intervals cannot be expected to provide an accurate representation of the uncertainty of effective cluster interactions (ECIs) in the CE due to the nature of the target ab initio data and the nature of CEs themselves. We develop a method for estimating these errors that does not rely on statistical assumptions about the model or data. We then use these ECI errors to quantify fundamental consequences on the uncertainty of ECIs in CEs built from O/Fe(100) data whose surface and adsorbates have been allowed to relax in a typical manner and from O/Fe(100) data whose surface and adsorbates are fixed in ideal lattice positions. We also quantify the effect of using a different density functional theory exchange–correlation functional, using these ECI errors to assess the significance in any deviations. In both cases, our method is shown to have remarkable utility in the quantification of errors in the ECIs of CEs. While we stick to the lattice gas convention in this work, the method is equally applicable to the Ising convention or, in principle, any linear model of sufficient complexity.« less

Ab initio molecular dynamics simulations combined with enhanced sampling techniques are becoming widespread methods to investigate chemical phenomena in catalytic systems. These techniques automatically include finite temperature effects, anharmonicity, and collective dynamics in their robust description of enthalpic and entropic contributions, which can have significant impact on reaction free energy landscapes. This contrasts with standard ab initio static approaches that are based on assessing reaction free energies from various coarse-grained descriptions of the reaction potential energy surface. Enhanced sampling ab initio molecular dynamics opens the way to first principles simulations of systems of increasing complexity like solid/liquid catalytic interfaces. Here,more » we aim at guiding the reader through the basis of these techniques, summarizing their fundamental theoretical and practical aspects, and reviewing the relevant literature in the field. After a brief introduction to the problem, we will illustrate the advantage of using molecular simulations to include finite temperature effects, examine the most common ab initio techniques currently in use, describe their application to solid state heterogeneous catalysts, and finally critically review the most popular enhanced sampling techniques used in computational catalysis.« less

The analogy between single-atom catalysts (SACs) and molecular catalysts predicts that the specific catalytic activity of these systems is constant. Here we provide evidence that this prediction is not necessarily true. As a case in point, we show that the specific activity over ceria-supported single Pd atoms linearly increases with metal atom density, originating from the cumulative enhancement of CeO₂ reducibility. The long-range electrostatic footprints (≈1.5 nm) around each Pd site overlap with each other as surface Pd density increases, resulting in an observed deviation from constant specific activity. These cooperative effects exhaust previously active O atoms above a certainmore » Pd density, leading to their permanent removal and a consequent drop in reaction rate. The findings of our combined experimental and computational study show that the specific catalytic activity of reducible oxide-supported single-atom catalysts can be tuned by varying the surface density of single metal atoms.« less

In catalysis, MgO is often used to modify the acid-base properties of support oxides and to stabilize supported metal atoms and particles on oxides. In this study, we show how the sublimation of MgO powder can be used to deposit MgO monomers, hither on anatase TiO₂(101). A combination of X-ray electron spectroscopy, high-resolution scanning tunneling microscopy, and density functional theory is employed to gain insight into the MgO monomer binding, electronic and vibrational properties, and thermal stability. In the most stable configuration, the Mg and O of the MgO monomer bind to two surface oxygens and one undercoordinated surface titanium,more » respectively. The additional binding weakens the Mg-O monomer bond and makes the Mg more ionic. The monomers are thermally stable up to 650 K, where the onset of diffusion into the TiO₂ bulk is observed. Finally, the monomeric MgO species on TiO₂(101) represent an ideal, atomically precise system with modified acid-base properties and will be employed in our future catalytic studies.« less