4 Search Results

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics,more » and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.« less

Oxymethylene ethers (OMEs) have been studied in recent years for use as compression ignition fuel blendstocks, but the methyl-terminated OMEs commonly studied exhibit properties that are poorly optimized for engine use and distribution. Recent work has shown that OMEs with larger (ethyl, propyl, or butyl) end groups may have superior properties for fuel usage/storage. In this work, we consider ignition of four OMEs - diethoxymethane (E-1-E), dipropoxymethane (P-1-P), ethoxy-(methoxy)₂-ethane (E-2-E), and diisopropoxymethane (iP-1-iP) - as representatives of the possible effects of changes to OME structures. To our knowledge, ignition behaviors of the latter three fuels have not been studied priormore » to this work. Further, we find that all of the tested linear OMEs (E-1-E, P-1-P, and E-2-E) show two-stage ignition at low temperatures and nonlinear ignition behavior, consistent with literature on methyl-terminated OMEs and E-1-E. The nonlinear, branched OME (iP-1-iP) required higher pressure and temperature to ignite than the linear OMEs; further, this fuel experienced only single stage ignition and a linear ignition delay curve. By analogy to existing kinetic mechanisms for ethers and higher alcohols, the chemical basis for the observed trends are hypothesized. Faster ignition of E-2-E results from the additional oxymethylene group providing additional sites for ROO formation and more possible QOOH structures. Slower low temperature ignition of P-1-P is driven by lower H abstraction rates in comparison to E-1-E, however at high temperatures P-1-P ignites faster, driven by increasing abstraction from the additional H site on the propyl group that opens up additional QOOH formation pathways. iP-1-iP ignition is slowed significantly by preferential H abstraction from the central carbon of the isopropyl group, which is crowded and unlikely to bond with O₂, however at high temperatures, abstraction from H sites on the methyl groups allows for the ROO cascade initiation and subsequent rapid ignition.« less

Oxymethylene ethers (OMEs) have been studied as possible additives or replacements for diesel fuels. Typically, studies have considered only methyl-terminated OMEs. Recent structure-property relationship models suggest that extended-alkyl OMEs may provide improvements to many of the properties of methyl-terminated OMEs that make them less suitable as diesel fuel blendstocks. In this work, we describe the synthesis and characterization of 16 different OMEs with methyl, ethyl, propyl, butyl, isopropyl, and isobutyl terminating alkyl groups with varying oxymethylene chain length. Indicated Cetane Number, Lower Heating Value, Flash Point, Density, Viscosity, Vapor Pressure, and Oxidative Stability are tested via ASTM standard methods. Additionally,more » Water Solubility, Boiling Point, seal material compatibility, and sooting propensity (via the Yield Sooting Index) are measured for these fuels. For diesel compatibility, all tested OMEs except smaller methyl and ethyl OMEs, and the branched isopropyl OME, meet cetane number requirements. Further, extending the alkyl end group increases the heating value, but all OMEs, due to their oxygen content, have heating values less than diesel; despite this, all OMEs show significant reductions in soot production per unit heating value. Only the heaviest OMEs meet diesel viscosity requirements, and most are higher density than diesel. OMEs with larger alkyl groups show the highest stability under accelerated auto-oxidation conditions. Increases in alkyl group length cause order of magnitude reduction in water solubility, from hundreds of g/L for methyl terminated OMEs to hundreds of mg/L for butyl terminated OMEs. Limited seal material testing indicates that PEEK polymers are unaffected by OMEs; while extended alkyl groups may improve compatibility with FKM (Viton), other common elastomers (NBR, silicone) remain incompatible with all tested OMEs. Overall, it is found that methyl-terminated OMEs exhibit the most potential for soot reduction, but OMEs with larger propyl and butyl terminating alkyl groups show improved compatibility with existing diesel systems.« less