Strain partition and rupture analysis of notched tensile multilayered steel specimens
Abstract
Multilayered steel composites consisting of alternating martensitic and austenite layers were successfully fabricated with a combination of high strength and ductility. In situ SEM tensile experiments were performed to investigate the fracture processes. Results indicated that the martensitic layer distributed between two ductile austenite layers has better deformation ability, and the dimple fracture mode dominated the fracture of the whole specimen. In situ synchrotron microbeam X-ray diffraction experiments were carried out to study the microscopic deformation in austenitic layer and martensitic layer ahead of notch root under incremental tensile loading. Results indicated that for austenite layer, the maximum strain is located in the middle of the layer at the lower applied load. When at the higher applied load, larger strain is concentrated on the notch root. For martensitic layer, uniform strain is distributed at the region at the lower applied load, with increasing the applied load, small strain appears in the middle of martensitic layer. However, the variation in the strain in the martensitic layer is relatively smaller, which is actually affected by both the notch and the ferrite content in the martensitic layer. Furthermore, the changing trends of the strain in the austenite layer and martensitic layer can stillmore »
- Authors:
-
- Lanzhou Univ. of Technology, Lanzhou (China); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
- Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
- Argonne National Lab. (ANL), Lemont, IL (United States)
- Univ. of Tokyo, Tokyo (Japan)
- Publication Date:
- Research Org.:
- Argonne National Lab. (ANL), Argonne, IL (United States)
- Sponsoring Org.:
- USDOE Office of Science (SC); National Natural Science Foundation of China (NSFC)
- OSTI Identifier:
- 1508367
- Grant/Contract Number:
- AC02-06CH11357
- Resource Type:
- Accepted Manuscript
- Journal Name:
- Materials Characterization
- Additional Journal Information:
- Journal Volume: 145; Journal Issue: C; Journal ID: ISSN 1044-5803
- Publisher:
- Elsevier
- Country of Publication:
- United States
- Language:
- English
- Subject:
- 36 MATERIALS SCIENCE; austenite; in-situ SEM tensile; in-situ synchrotron; martensitic; multilayered steel composite
Citation Formats
Cao, R., Yu, X., Feng, Z., Liu, W., Xu, R., Ojima, M., and Koseki, T. Strain partition and rupture analysis of notched tensile multilayered steel specimens. United States: N. p., 2018.
Web. doi:10.1016/j.matchar.2018.09.027.
Cao, R., Yu, X., Feng, Z., Liu, W., Xu, R., Ojima, M., & Koseki, T. Strain partition and rupture analysis of notched tensile multilayered steel specimens. United States. https://doi.org/10.1016/j.matchar.2018.09.027
Cao, R., Yu, X., Feng, Z., Liu, W., Xu, R., Ojima, M., and Koseki, T. Tue .
"Strain partition and rupture analysis of notched tensile multilayered steel specimens". United States. https://doi.org/10.1016/j.matchar.2018.09.027. https://www.osti.gov/servlets/purl/1508367.
@article{osti_1508367,
title = {Strain partition and rupture analysis of notched tensile multilayered steel specimens},
author = {Cao, R. and Yu, X. and Feng, Z. and Liu, W. and Xu, R. and Ojima, M. and Koseki, T.},
abstractNote = {Multilayered steel composites consisting of alternating martensitic and austenite layers were successfully fabricated with a combination of high strength and ductility. In situ SEM tensile experiments were performed to investigate the fracture processes. Results indicated that the martensitic layer distributed between two ductile austenite layers has better deformation ability, and the dimple fracture mode dominated the fracture of the whole specimen. In situ synchrotron microbeam X-ray diffraction experiments were carried out to study the microscopic deformation in austenitic layer and martensitic layer ahead of notch root under incremental tensile loading. Results indicated that for austenite layer, the maximum strain is located in the middle of the layer at the lower applied load. When at the higher applied load, larger strain is concentrated on the notch root. For martensitic layer, uniform strain is distributed at the region at the lower applied load, with increasing the applied load, small strain appears in the middle of martensitic layer. However, the variation in the strain in the martensitic layer is relatively smaller, which is actually affected by both the notch and the ferrite content in the martensitic layer. Furthermore, the changing trends of the strain in the austenite layer and martensitic layer can still show the better combination of brittle martensitic phase and ductile austenite phase.},
doi = {10.1016/j.matchar.2018.09.027},
journal = {Materials Characterization},
number = C,
volume = 145,
place = {United States},
year = {Tue Sep 18 00:00:00 EDT 2018},
month = {Tue Sep 18 00:00:00 EDT 2018}
}
Web of Science
Figures / Tables:
Works referenced in this record:
Fabrication and Machining of Metal Matrix Composites: A Review
journal, March 2015
- Bains, Preetkanwal Singh; Sidhu, Sarabjeet Singh; Payal, H. S.
- Materials and Manufacturing Processes, Vol. 31, Issue 5
Bending, buckling and free vibration of laminated composite and sandwich beams: A critical review of literature
journal, July 2017
- Sayyad, Atteshamuddin S.; Ghugal, Yuwaraj M.
- Composite Structures, Vol. 171
Mechanical behaviour of laminated metal composites
journal, January 1996
- Lesuer, D. R.; Syn, C. K.; Sherby, O. D.
- International Materials Reviews, Vol. 41, Issue 5
Improvement of the mechanical properties of austenitic stainless steel after plasma nitriding
journal, November 2000
- Menthe, E.; Bulak, A.; Olfe, J.
- Surface and Coatings Technology, Vol. 133-134
Improved creep strength and creep ductility of type 347 austenitic stainless steel through the self-healing effect of boron for creep cavitation
journal, February 2005
- Laha, K.; Kyono, J.; Sasaki, T.
- Metallurgical and Materials Transactions A, Vol. 36, Issue 2
Development of nitrogen-containing nickel-free austenitic stainless steels for metallic biomaterials—review
journal, December 2004
- Sumita, M.; Hanawa, T.; Teoh, S. H.
- Materials Science and Engineering: C, Vol. 24, Issue 6-8
Effect of delta ferrite on impact properties of low carbon 13Cr–4Ni martensitic stainless steel
journal, May 2010
- Wang, P.; Lu, S. P.; Xiao, N. M.
- Materials Science and Engineering: A, Vol. 527, Issue 13-14
Using heat sink technology to decrease residual stress in 316L stainless steel welding joint: Finite element simulation
journal, April 2012
- Jiang, Wenchun; Zhang, Yucai; Woo, Wanchuck
- International Journal of Pressure Vessels and Piping, Vol. 92
Effects of the rolling temperature on microstructure and mechanical properties of 2Cr13/316L laminated composites prepared by accumulative roll-bonding (ARB)
journal, May 2018
- Cao, R.; Zhao, X. K.; Ding, Y.
- Materials Characterization, Vol. 139
Fracture elongation of brittle/ductile multilayered steel composites with a strong interface
journal, November 2008
- Inoue, Junya; Nambu, Shoichi; Ishimoto, Yoshitake
- Scripta Materialia, Vol. 59, Issue 10
Relationship between local deformation behavior and crystallographic features of as-quenched lath martensite during uniaxial tensile deformation
journal, October 2009
- Michiuchi, M.; Nambu, S.; Ishimoto, Y.
- Acta Materialia, Vol. 57, Issue 18
Interphase Strain Gradients in Multilayered Steel Composite from Microdiffraction
journal, November 2013
- Barabash, Rozaliya I.; Barabash, Oleg M.; Ojima, Mayumi
- Metallurgical and Materials Transactions A, Vol. 45, Issue 1
Effect of Annealing Temperature and Time on Microstructure and Mechanical Properties of Multilayered Steel Composite Sheets
journal, October 2016
- Cao, R.; Yu, X.; Feng, Z.
- Metallurgical and Materials Transactions A, Vol. 47, Issue 12
Stress partitioning behavior of multilayered steels during tensile deformation measured by in situ neutron diffraction
journal, February 2012
- Ojima, M.; Inoue, J.; Nambu, S.
- Scripta Materialia, Vol. 66, Issue 3-4
Strain field in a brittle/ductile multilayered steel composite
journal, May 2011
- Lhuissier, P.; Inoue, J.; Koseki, T.
- Scripta Materialia, Vol. 64, Issue 10
The role of residual stresses in layered composites of Y–ZrO2 and Al2O3
journal, February 1999
- Tomaszewski, Henryk; Strzeszewski, Jan; Gȩbicki, Wojciech
- Journal of the European Ceramic Society, Vol. 19, Issue 2
Effects of low-temperature transformation and transformation-induced plasticity on weld residual stresses: Numerical study and neutron diffraction measurement
journal, June 2018
- Jiang, Wenchun; Chen, Wei; Woo, Wanchuck
- Materials & Design, Vol. 147
Stress partitioning among ferrite, martensite and retained austenite of a TRIP-assisted multiphase steel: An in-situ high-energy X-ray diffraction study
journal, May 2018
- Song, Chenghao; Yu, Hao; Lu, Jun
- Materials Science and Engineering: A, Vol. 726
Mechanical stability of individual austenite grains in TRIP steel studied by synchrotron X-ray diffraction during tensile loading
journal, November 2014
- Blondé, R.; Jimenez-Melero, E.; Zhao, L.
- Materials Science and Engineering: A, Vol. 618
Effects of retained austenite volume fraction, morphology, and carbon content on strength and ductility of nanostructured TRIP-assisted steels
journal, June 2015
- Shen, Y. F.; Qiu, L. N.; Sun, X.
- Materials Science and Engineering: A, Vol. 636
In situ room temperature tensile deformation of a 1% CrMoV bainitic steel using synchrotron and neutron diffraction
journal, June 2011
- Weisser, M. A.; Evans, A. D.; Van Petegem, S.
- Acta Materialia, Vol. 59, Issue 11
An in situ high-energy X-ray diffraction study of micromechanical behavior of multiple phases in advanced high-strength steels
journal, August 2009
- Jia, N.; Cong, Z. H.; Sun, X.
- Acta Materialia, Vol. 57, Issue 13
In-situ stress and strain measurements around cracks using synchrotron X-ray diffraction
journal, July 2011
- Steuwer, A.; Daniels, J. E.
- The Journal of Strain Analysis for Engineering Design, Vol. 46, Issue 7
3D X-Ray Crystal Microscope
journal, October 2000
- Ice, G. E.; Larson, B. C.
- Advanced Engineering Materials, Vol. 2, Issue 10
Three-dimensional X-ray structural microscopy with submicrometre resolution
journal, February 2002
- Larson, B. C.; Yang, Wenge; Ice, G. E.
- Nature, Vol. 415, p. 887-890
Measuring depth-dependent dislocation densities and Elastic strains in an indented Ni-based Superalloy
journal, December 2010
- Barabash, O. M.; Santella, M.; Barabash, R. I.
- JOM, Vol. 62, Issue 12
Microscopic Deformation in Individual Grains in an Advanced High-Strength Steel
journal, November 2012
- Yu, Zhenzhen; Barabash, Rozaliya; Barabash, Oleg
- JOM, Vol. 65, Issue 1
Differential-aperture X-ray structural microscopy: a submicron-resolution three-dimensional probe of local microstructure and strain
journal, August 2004
- Yang, Wenge; Larson, B. C.; Tischler, J. Z.
- Micron, Vol. 35, Issue 6
Thermal residual stress in metal matrix composite
journal, March 1987
- Arsenault, R. J.; Taya, M.
- Acta Metallurgica, Vol. 35, Issue 3
Phase-stress partition and residual stress in metal matrix composites
journal, September 2000
- Zhonghua, Li; Schmauder, S.
- Computational Materials Science, Vol. 18, Issue 3-4
A new criterion for elasto-plastic transition in nanomaterials: Application to size and composite effects on Cu–Nb nanocomposite wires
journal, June 2009
- Thilly, Ludovic; Petegem, Steven Van; Renault, Pierre-Olivier
- Acta Materialia, Vol. 57, Issue 11
Phase-stress partition and stress-induced martensitic transformation in NbTi/NiTi nanocomposite
journal, August 2011
- Hao, S. J.; Jiang, D. Q.; Cui, L. S.
- Applied Physics Letters, Vol. 99, Issue 8
Works referencing / citing this record:
Genetic programming in the steelmaking industry
journal, February 2020
- Kovačič, Miha; Župerl, Uroš
- Genetic Programming and Evolvable Machines, Vol. 21, Issue 1-2
Figures / Tables found in this record: