Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy

Radetić, T.; Popović, M.; Jegdić, B.; Romhanji, E.

doi:10.1002/maco.201508709

Title: Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy

Abstract

Influence of annealing temperature on β‐(Al ₃ Mg ₂ ) phase precipitation and corrosion properties of sensitised Al‐6.8 wt% Mg alloy is investigated. Sensitisation of specimens annealed at 320 °C results in IGC and SCC susceptibility. Microstructural characterization shows fine precipitation of Mg‐rich phase forming nearly continuous film at grain boundaries, despite small precipitated fraction (0.5%), and grain boundary faceting. Sensitised specimens annealed at 265 °C are IGC susceptible, but SCC resistant. Precipitation at grain boundaries is discrete, although the precipitated fraction is greater (3%) than in specimens annealed at 320 °C. Potentiodynamic measurements show that of all measured parameters, charge density is in the strongest correlation with the NAMLT and SSRT results.

Authors:

Radetić, T. ^[1]; Popović, M. ^[1]; Jegdić, B. ^[2]; Romhanji, E. ^[1]

Department of Metallurgical Engineering, Faculty of Technology and Metallurgy University of Belgrade Karnegijeva 4, POB 35‐03 11 120 Belgrade Serbia
ICTM‐Department of Electrochemistry University of Belgrade Njegoševa 12 11 120 Belgrade Serbia

Publication Date:: Fri Jan 22 00:00:00 EST 2016

Sponsoring Org.:: USDOE

OSTI Identifier:: 1400539

Grant/Contract Number:: DE‐AC02‐05CH11231

Resource Type:: Publisher's Accepted Manuscript

Journal Name:: Materials and Corrosion

Additional Journal Information:: Journal Name: Materials and Corrosion Journal Volume: 67 Journal Issue: 8; Journal ID: ISSN 0947-5117

Publisher:: Wiley Blackwell (John Wiley & Sons)

Country of Publication:: Germany

Language:: English

Citation Formats


                    Radetić, T., Popović, M., Jegdić, B., and Romhanji, E. Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy.  Germany: N. p., 2016. 
Web.  doi:10.1002/maco.201508709.

Copy to clipboard


                    Radetić, T., Popović, M., Jegdić, B., & Romhanji, E. Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy.  Germany.  https://doi.org/10.1002/maco.201508709

Copy to clipboard


                    Radetić, T., Popović, M., Jegdić, B., and Romhanji, E. Fri .  
"Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy".  Germany.  https://doi.org/10.1002/maco.201508709.

Copy to clipboard


                    
@article{osti_1400539,

  title        = {Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy},

  author       = {Radetić, T. and Popović, M. and Jegdić, B. and Romhanji, E.},

  abstractNote = {Influence of annealing temperature on β‐(Al 3 Mg 2 ) phase precipitation and corrosion properties of sensitised Al‐6.8 wt% Mg alloy is investigated. Sensitisation of specimens annealed at 320 °C results in IGC and SCC susceptibility. Microstructural characterization shows fine precipitation of Mg‐rich phase forming nearly continuous film at grain boundaries, despite small precipitated fraction (0.5%), and grain boundary faceting. Sensitised specimens annealed at 265 °C are IGC susceptible, but SCC resistant. Precipitation at grain boundaries is discrete, although the precipitated fraction is greater (3%) than in specimens annealed at 320 °C. Potentiodynamic measurements show that of all measured parameters, charge density is in the strongest correlation with the NAMLT and SSRT results.},

  doi          = {10.1002/maco.201508709},

  journal      = {Materials and Corrosion},

  number       = 8,

  volume       = 67,

  place        = {Germany},

  year         = {Fri Jan 22 00:00:00 EST 2016},

  month        = {Fri Jan 22 00:00:00 EST 2016}

}

Copy to clipboard

Journal Article:

Free Publicly Available Full Text

Accepted Manuscript (Publisher)

Publisher's Version of Record
https://doi.org/10.1002/maco.201508709

Other availability

Search WorldCat to find libraries that may hold this journal

Citation Metrics:

Cited by: 4 works

Citation information provided by
Web of Science

Save / Share:

Export Metadata

Save to My Library

Works referenced in this record:

Role of Mg in the stress corrosion cracking of an Al-Mg alloy
journal, July 2001

Jones, R. H.; Baer, D. R.; Danielson, M. J.
Metallurgical and Materials Transactions A, Vol. 32, Issue 7
DOI: 10.1007/s11661-001-0148-0

The nucleation and initial stages of growth of grain boundary precipitates in Al-Zn-Mg and Al-Mg alloys
journal, November 1969

Unwin, P. N. T.; Nicholson, R. B.
Acta Metallurgica, Vol. 17, Issue 11
DOI: 10.1016/0001-6160(69)90155-2

The Polarization Resistance Technique for Measuring Corrosion Currents
book, January 1976

Mansfeld, Florian
Advances in Corrosion Science and Technology
DOI: 10.1007/978-1-4684-8986-6_3

Effect of sensitization heat treatment on properties of Al–Mg alloy AA5083-H116
journal, June 2008

Oguocha, I. N. A.; Adigun, O. J.; Yannacopoulos, S.
Journal of Materials Science, Vol. 43, Issue 12
DOI: 10.1007/s10853-008-2606-1

Spreading of intergranular corrosion on the surface of sensitized Al-4.4Mg alloys: A general finding
journal, June 2012

Jain, S.; Lim, M. L. C.; Hudson, J. L.
Corrosion Science, Vol. 59
DOI: 10.1016/j.corsci.2012.02.018

Characterization of microstructural changes in an Al-6.8wt.% Mg alloy by electrical resistivity measurements
journal, September 2008

Popović, Miljana; Romhanji, Endre
Materials Science and Engineering: A, Vol. 492, Issue 1-2
DOI: 10.1016/j.msea.2008.04.001

A study of intergranular fracture in an aluminium alloy due to hydrogen embrittlement
journal, July 2012

Pouillier, E.; Gourgues, A. -F.; Tanguy, D.
International Journal of Plasticity, Vol. 34
DOI: 10.1016/j.ijplas.2012.01.004

Microstructural Evolution and Stress Corrosion Cracking Behavior of Al-5083
journal, June 2010

Goswami, R.; Spanos, G.; Pao, P. S.
Metallurgical and Materials Transactions A, Vol. 42, Issue 2
DOI: 10.1007/s11661-010-0262-y

Intergranular Corrosion and Stress Corrosion Cracking of Sensitised AA5182
journal, July 2006

Davenport, Alison J.; Yuan, Yudie; Ambat, Rajan
Materials Science Forum, Vol. 519-521
DOI: 10.4028/www.scientific.net/MSF.519-521.641

A Comparison of the Corrosion Behavior of Nanocrystalline and Conventional Al 5083 Samples
journal, February 2006

Kus, E.; Lee, Z.; Nutt, S.
CORROSION, Vol. 62, Issue 2
DOI: 10.5006/1.3278260

Effect of annealing treatment on the mechanical properties and corrosion behaviors of 01570 aluminum alloy: Effect of annealing treatment on corrosion of 01570 Al alloy
journal, March 2013

Wang, X. H.; Wang, J. H.; Song, J.
Materials and Corrosion, Vol. 65, Issue 8
DOI: 10.1002/maco.201206867

Effect of thermomechanical treatment on the corrosion of AA5083
journal, February 2010

Tan, L.; Allen, T. R.
Corrosion Science, Vol. 52, Issue 2
DOI: 10.1016/j.corsci.2009.10.013

The protection potential of aluminium
journal, January 1978

Nisancioglu, K.; Holtan, H.
Corrosion Science, Vol. 18, Issue 11
DOI: 10.1016/0010-938X(78)90035-5

Al-Mg-Mn (Aluminum-Magnesium-Manganese)
journal, October 2009

Raghavan, V.
Journal of Phase Equilibria and Diffusion, Vol. 30, Issue 6
DOI: 10.1007/s11669-009-9591-1

Influence of the Thermomechanical Treatment on the Intergranular Corrosion Susceptibility of Zn-Modified Al-5.1 Wt Pct Mg-0.7 Wt Pct Mn Alloy Sheet
journal, June 2014

Halap, Akram; Radetić, Tamara; Popović, Miljana
Metallurgical and Materials Transactions A, Vol. 45, Issue 10
DOI: 10.1007/s11661-014-2386-y

Aluminium Alloys for Automotive Application
journal, January 1997

Hirsch, Jürgen
Materials Science Forum, Vol. 242
DOI: 10.4028/www.scientific.net/MSF.242.33

Stress Corrosion Cracking of Al-Mg and Mg-Al Alloys
journal, December 2004

Jones, R. H.; Vetrano, J. S.; Windisch, C. F.
CORROSION, Vol. 60, Issue 12
DOI: 10.5006/1.3299228

Crack-particle interactions during intergranular stress corrosion of AA5083 as observed by cross-section transmission electron microscopy
journal, May 2004

Jones, R. H.; Gertsman, V. Y.; Vetrano, J. S.
Scripta Materialia, Vol. 50, Issue 10
DOI: 10.1016/j.scriptamat.2004.01.038

Effect of low temperature sensitization on the susceptibility to intergranular corrosion in AA5083 aluminum alloy: Effect of low temperature sensitization in AA5083 aluminum alloy
journal, October 2015

Wei, W.; González, S.; Hashimoto, T.
Materials and Corrosion, Vol. 67, Issue 4
DOI: 10.1002/maco.201508589

Heterogeneous distributions of Magnesium atoms near the precipitate in Al-Mg based alloys
journal, February 1995

Yukawa, H.; Murata, Y.; Morinaga, M.
Acta Metallurgica et Materialia, Vol. 43, Issue 2
DOI: 10.1016/0956-7151(94)00266-K

Monitoring the precipitation reactions in a cold-rolled Al–Mn–Mg–Cu alloy using thermoelectric power and electrical resistivity measurements
journal, August 2001

Vooijs, S. I.; Davenport, S. B.; Todd, I.
Philosophical Magazine A, Vol. 81, Issue 8
DOI: 10.1080/01418610108216652

Mechanism of intergranular corrosion of Al-Cu alloys
journal, January 1970

Galvele, J. R.; de De Micheli, S. M.
Corrosion Science, Vol. 10, Issue 11
DOI: 10.1016/S0010-938X(70)80003-8

Stress corrosion cracking susceptibility of ultrafine grained Al–Mg–Sc alloy
journal, March 2013

Argade, G. R.; Kumar, N.; Mishra, R. S.
Materials Science and Engineering: A, Vol. 565
DOI: 10.1016/j.msea.2012.11.066

Mass-Transport-Limited Oxygen Reduction Reaction on AA2024-T3 and Selected Intermetallic Compounds in Chromate-Containing Solutions
journal, February 2001

Ilevbare, G. O.; Scully, J. R.
CORROSION, Vol. 57, Issue 2
DOI: 10.5006/1.3290339

Hydrogen effects during IGSCC of pure Al–5Mg alloy in NaCl media
journal, June 2002

Tanguy, D.; Bayle, B.; Dif, R.
Corrosion Science, Vol. 44, Issue 6
DOI: 10.1016/S0010-938X(01)00140-8

Rotating cage and jet impingement techniques
book, January 2008

Papavinasam, Sankara
Techniques for Corrosion Monitoring
DOI: 10.1533/9781845694050.2.322

Influence of Mg Content on the Sensitization and Corrosion of Al-xMg(-Mn) Alloys
journal, November 2013

Gupta, R. K.; Zhang, R.; Davies, C. H. J.
CORROSION, Vol. 69, Issue 11
DOI: 10.5006/0948

Evaluation of Al3Mg2 Precipitates and Mn-Rich Phase in Aluminum-Magnesium Alloy Based on Scanning Transmission Electron Microscopy Imaging
journal, August 2012

Zhu, Yakun; Cullen, David A.; Kar, Soumya
Metallurgical and Materials Transactions A, Vol. 43, Issue 13
DOI: 10.1007/s11661-012-1354-7

Tem-studies of grain boundaries in cyclically deformed AlZnMg-bicrystals
journal, September 1992

Wunderlich, W.; Gudladt, H. -J.
Acta Metallurgica et Materialia, Vol. 40, Issue 9
DOI: 10.1016/0956-7151(92)90129-3

Stress-corrosion cracking susceptibility of the superplastically formed 5083 aluminum alloy in 3.5 pct NaCl solution
journal, December 1999

Chang, J. C.; Chuang, T. H.
Metallurgical and Materials Transactions A, Vol. 30, Issue 12
DOI: 10.1007/s11661-999-0229-z

The role of magnesium segregation in the intergranular stress corrosion cracking of aluminium alloys
journal, January 1987

Scamans, G. M.; Holroyd, N. J. H.; Tuck, C. D. S.
Corrosion Science, Vol. 27, Issue 4
DOI: 10.1016/0010-938X(87)90076-X

Corrosion Behavior of Nanocrystalline Bulk Al-Mg-Based Alloys
journal, April 2004

Sikora, E.; Wei, X. J.; Shaw, B. A.
CORROSION, Vol. 60, Issue 4
DOI: 10.5006/1.3287748

The Degradation of Corrosion Resistance for Al 5083 Alloy after Thermal and Superplastic Forming Processes
journal, June 2000

Chang, J. C.; Chuang, T. H.
Journal of Materials Engineering and Performance, Vol. 9, Issue 3
DOI: 10.1361/105994900770345881

Direct visualization of β phase causing intergranular forms of corrosion in Al–Mg alloys
journal, June 2013

Yang, Young-Ki; Allen, Todd
Materials Characterization, Vol. 80
DOI: 10.1016/j.matchar.2013.03.014

Effects of Zn additions on the grain boundary precipitation and corrosion of Al-5083
journal, January 2000

Carroll, M. C.; Gouma, P. I.; Mills, M. J.
Scripta Materialia, Vol. 42, Issue 4
DOI: 10.1016/S1359-6462(99)00349-8

The Ageing and Thermal Recovery Behaviour of Al-Mg-Cu Alloys
journal, July 2002

Court, S. A.; Hicklin, K. P.; Lloyd, David J.
Materials Science Forum, Vol. 396-402
DOI: 10.4028/www.scientific.net/MSF.396-402.1031

The Effect of Grain-Boundary Structure Formation on β-Precipitation in Aged Al-Mg Alloys
journal, November 1998

Kaigorodova, L. I.
Materials Science Forum, Vol. 294-296
DOI: 10.4028/www.scientific.net/MSF.294-296.477

Transmission Electron Microscopic Investigations of Grain Boundary Beta Phase Precipitation in Al 5083 Aged at 373 K (100 °C)
journal, May 2012

Goswami, Ramasis; Holtz, Ronald L.
Metallurgical and Materials Transactions A, Vol. 44, Issue 3
DOI: 10.1007/s11661-012-1166-9

Stress corrosion cracking susceptibility of Al–Mg alloy sheet with high Mg content
journal, September 2002

Popović, Miljana; Romhanji, Endre
Journal of Materials Processing Technology, Vol. 125-126
DOI: 10.1016/S0924-0136(02)00398-9

Determination of the β Solvus Temperature of the Aluminum Alloy 5083
journal, June 2013

Yang, Young-Ki; Allen, Todd R.
Metallurgical and Materials Transactions A, Vol. 44, Issue 11
DOI: 10.1007/s11661-013-1837-1

Precipitation at grain boundaries in the commercial alloy Al 7075
journal, December 1986

Park, J. K.; Ardell, A. J.
Acta Metallurgica, Vol. 34, Issue 12
DOI: 10.1016/0001-6160(86)90143-4

Grain boundary misorientation dependence of β phase precipitation in an Al–Mg alloy
journal, April 2014

Scotto D’Antuono, D.; Gaies, J.; Golumbfskie, W.
Scripta Materialia, Vol. 76
DOI: 10.1016/j.scriptamat.2014.01.003

Stress corrosion cracking of sensitized AA5083 (Al-4.5Mg-1.0Mn)
journal, November 2001

Searles, J. L.; Gouma, P. I.; Buchheit, R. G.
Metallurgical and Materials Transactions A, Vol. 32, Issue 11
DOI: 10.1007/s11661-001-1036-3

Similar Records in DOE PAGES and OSTI.GOV collections:

Stress-corrosion cracking susceptibility of the superplastically formed 5083 aluminum alloy in 3.5 pct NaCl solution

Journal Article Chang, J C ; Chuang, T H - Metallurgical and Materials Transactions. A, Physical Metallurgy and Materials Science

The slow strain rate test (SSRT) method was employed to study the stress corrosion cracking (SCC) susceptibility of the superplastic 5083 Al alloy in a 3.5% NaCl solution after superplastic forming and various heat treatments. Experimental results showed that both superplastically formed specimens and specimens subject to the same thermal processes as that used in superplastic forming suffered severe SCC susceptibility, and obvious intergranular fracture surfaces were also observed. Furthermore, scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDS) analyses demonstrated that the thermal processes of superplastic forming led to continuously distributed precipitation layers of {beta} phase (Mg{sub 2}Al{submore »« less
https://doi.org/10.1007/s11661-999-0229-z
Low-temperature stress corrosion cracking of alloy 601 in thiosulfate and chloride solutions

Journal Article Gonzalez-Rodriguez, J G ; Salinas-Bravo, V M ; Martinez-Villafane, A - Corrosion

The stress corrosion cracking (SCC) susceptibility of unsensitized and sensitized alloy 601 (UNS N06601) was studied in sodium thiosulfate (Na{sub 2}S{sub 2}O{sub 3}) and sodium chloride (NaCl) solutions using slow strain rate testing (SSRT). Specimens were tested in the as-received condition (mill-annealed) after solution annealing at 1,050 C for 30 min and after solution annealing and sensitizing for 2, 5, 24, or 772 h at 700 for 30 min. Environments included Na{sub 2}S{sub 2}O{sub 3} and NaCl at different concentrations ranging from 0.01 M to 1.0 M at 25 C and 95 C. Double-loop electrochemical potentiokinetic reactivation (DL-EPR) tests inmore »« less
https://doi.org/10.5006/1.3283963
Environmentally assisted cracking in light water reactors.

Technical Report Chopra, O K ; Chung, H M ; Clark, R W ; ...

This report summarizes work performed by Argonne National Laboratory on fatigue and environmentally assisted cracking (EAC) in light water reactors (LWRs) from January to December 2002. Topics that have been investigated include: (a) environmental effects on fatigue crack initiation in carbon and low-alloy steels and austenitic stainless steels (SSs), (b) irradiation-assisted stress corrosion cracking (IASCC) of austenitic SSs in BWRs, (c) evaluation of causes and mechanisms of irradiation-assisted cracking of austenitic SS in PWRs, and (d) cracking in Ni-alloys and welds. A critical review of the ASME Code fatigue design margins and an assessment of the conservation in the currentmore »« less
https://doi.org/10.2172/919337

Full Text Available
Grain boundary segregation and intergranular stress corrosion cracking susceptibility of austenitic stainless steels in high temperature water

Conference Shoji, T ; Yamaki, K ; Ballinger, R G ; ...

The effects of grain boundary segregation on intergranular stress corrosion cracking of austenitic stainless steels in high temperature water have been examined as a function of heat treatment. The materials investigated were: (1) two commercial purity Type 304; (2) low sulfur Type 304; (3) nuclear grade Type 304; (4) ultra high purity Type 304L; and (5) Type 316L and Type 347L. Specimens were solution treated at 1050{degrees}C for 0.5 hour and given a sensitization heat treatment at 650{degrees}C for 50 hours. Some of the specimens were then subjected to an aging heat treatment at 850{degrees}C for from one to tenmore »« less
Effect of heat treatment on SCC and HEC of precipitate-hardenable alloy in sour gas environment

Conference Takaoka, T ; Ishizawa, Y ; Misao, H ; ...

This paper reports on a gamma prime precipitate hardenable alloy (22%Cr-48%Ni-3%Mo-2.7%Ti-0.6%Al-0.5%Nb-Fe) tested for the resistance to SCC (stress corrosion cracking) and HEC (hydrogen embrittlement cracking) in H{sub 2}S and Cl environments. In this alloy, the susceptibility to both SCC and HEC was enhanced by the increase of the yield strength rather than by aging conditions. In addition to gamma prime precipitation in matrix, M{sub 23}C{sub 6} carbide and sigma phase precipitated at grain boundaries during high temperature aging with time. This sigma phase was not only deleterious for ductility, but also enhanced the intergranular SCC. The grain size also affectedmore »« less

Similar Records

Title: Influence of annealing temperature on sensitisation behaviour and corrosion properties of an Al‐6.8 wt% Mg alloy

Abstract

Citation Formats

Role of Mg in the stress corrosion cracking of an Al-Mg alloy journal, July 2001

The nucleation and initial stages of growth of grain boundary precipitates in Al-Zn-Mg and Al-Mg alloys journal, November 1969

The Polarization Resistance Technique for Measuring Corrosion Currents book, January 1976

Effect of sensitization heat treatment on properties of Al–Mg alloy AA5083-H116 journal, June 2008

Spreading of intergranular corrosion on the surface of sensitized Al-4.4Mg alloys: A general finding journal, June 2012

Characterization of microstructural changes in an Al-6.8wt.% Mg alloy by electrical resistivity measurements journal, September 2008

A study of intergranular fracture in an aluminium alloy due to hydrogen embrittlement journal, July 2012

Microstructural Evolution and Stress Corrosion Cracking Behavior of Al-5083 journal, June 2010

Intergranular Corrosion and Stress Corrosion Cracking of Sensitised AA5182 journal, July 2006

A Comparison of the Corrosion Behavior of Nanocrystalline and Conventional Al 5083 Samples journal, February 2006

Effect of annealing treatment on the mechanical properties and corrosion behaviors of 01570 aluminum alloy: Effect of annealing treatment on corrosion of 01570 Al alloy journal, March 2013

Effect of thermomechanical treatment on the corrosion of AA5083 journal, February 2010

The protection potential of aluminium journal, January 1978

Al-Mg-Mn (Aluminum-Magnesium-Manganese) journal, October 2009

Influence of the Thermomechanical Treatment on the Intergranular Corrosion Susceptibility of Zn-Modified Al-5.1 Wt Pct Mg-0.7 Wt Pct Mn Alloy Sheet journal, June 2014

Aluminium Alloys for Automotive Application journal, January 1997

Stress Corrosion Cracking of Al-Mg and Mg-Al Alloys journal, December 2004

Crack-particle interactions during intergranular stress corrosion of AA5083 as observed by cross-section transmission electron microscopy journal, May 2004

Effect of low temperature sensitization on the susceptibility to intergranular corrosion in AA5083 aluminum alloy: Effect of low temperature sensitization in AA5083 aluminum alloy journal, October 2015

Heterogeneous distributions of Magnesium atoms near the precipitate in Al-Mg based alloys journal, February 1995

Monitoring the precipitation reactions in a cold-rolled Al–Mn–Mg–Cu alloy using thermoelectric power and electrical resistivity measurements journal, August 2001

Mechanism of intergranular corrosion of Al-Cu alloys journal, January 1970

Stress corrosion cracking susceptibility of ultrafine grained Al–Mg–Sc alloy journal, March 2013

Mass-Transport-Limited Oxygen Reduction Reaction on AA2024-T3 and Selected Intermetallic Compounds in Chromate-Containing Solutions journal, February 2001

Hydrogen effects during IGSCC of pure Al–5Mg alloy in NaCl media journal, June 2002

Rotating cage and jet impingement techniques book, January 2008

Influence of Mg Content on the Sensitization and Corrosion of Al-xMg(-Mn) Alloys journal, November 2013

Evaluation of Al3Mg2 Precipitates and Mn-Rich Phase in Aluminum-Magnesium Alloy Based on Scanning Transmission Electron Microscopy Imaging journal, August 2012

Tem-studies of grain boundaries in cyclically deformed AlZnMg-bicrystals journal, September 1992

Stress-corrosion cracking susceptibility of the superplastically formed 5083 aluminum alloy in 3.5 pct NaCl solution journal, December 1999

The role of magnesium segregation in the intergranular stress corrosion cracking of aluminium alloys journal, January 1987

Corrosion Behavior of Nanocrystalline Bulk Al-Mg-Based Alloys journal, April 2004

The Degradation of Corrosion Resistance for Al 5083 Alloy after Thermal and Superplastic Forming Processes journal, June 2000

Direct visualization of β phase causing intergranular forms of corrosion in Al–Mg alloys journal, June 2013

Effects of Zn additions on the grain boundary precipitation and corrosion of Al-5083 journal, January 2000

The Ageing and Thermal Recovery Behaviour of Al-Mg-Cu Alloys journal, July 2002

The Effect of Grain-Boundary Structure Formation on β-Precipitation in Aged Al-Mg Alloys journal, November 1998

Transmission Electron Microscopic Investigations of Grain Boundary Beta Phase Precipitation in Al 5083 Aged at 373 K (100 °C) journal, May 2012

Stress corrosion cracking susceptibility of Al–Mg alloy sheet with high Mg content journal, September 2002

Determination of the β Solvus Temperature of the Aluminum Alloy 5083 journal, June 2013

Precipitation at grain boundaries in the commercial alloy Al 7075 journal, December 1986

Grain boundary misorientation dependence of β phase precipitation in an Al–Mg alloy journal, April 2014

Stress corrosion cracking of sensitized AA5083 (Al-4.5Mg-1.0Mn) journal, November 2001

Role of Mg in the stress corrosion cracking of an Al-Mg alloy
journal, July 2001

The nucleation and initial stages of growth of grain boundary precipitates in Al-Zn-Mg and Al-Mg alloys
journal, November 1969

The Polarization Resistance Technique for Measuring Corrosion Currents
book, January 1976

Effect of sensitization heat treatment on properties of Al–Mg alloy AA5083-H116
journal, June 2008

Spreading of intergranular corrosion on the surface of sensitized Al-4.4Mg alloys: A general finding
journal, June 2012

Characterization of microstructural changes in an Al-6.8wt.% Mg alloy by electrical resistivity measurements
journal, September 2008

A study of intergranular fracture in an aluminium alloy due to hydrogen embrittlement
journal, July 2012

Microstructural Evolution and Stress Corrosion Cracking Behavior of Al-5083
journal, June 2010

Intergranular Corrosion and Stress Corrosion Cracking of Sensitised AA5182
journal, July 2006

A Comparison of the Corrosion Behavior of Nanocrystalline and Conventional Al 5083 Samples
journal, February 2006

Effect of annealing treatment on the mechanical properties and corrosion behaviors of 01570 aluminum alloy: Effect of annealing treatment on corrosion of 01570 Al alloy
journal, March 2013

Effect of thermomechanical treatment on the corrosion of AA5083
journal, February 2010

The protection potential of aluminium
journal, January 1978

Al-Mg-Mn (Aluminum-Magnesium-Manganese)
journal, October 2009

Influence of the Thermomechanical Treatment on the Intergranular Corrosion Susceptibility of Zn-Modified Al-5.1 Wt Pct Mg-0.7 Wt Pct Mn Alloy Sheet
journal, June 2014

Aluminium Alloys for Automotive Application
journal, January 1997

Stress Corrosion Cracking of Al-Mg and Mg-Al Alloys
journal, December 2004

Crack-particle interactions during intergranular stress corrosion of AA5083 as observed by cross-section transmission electron microscopy
journal, May 2004

Effect of low temperature sensitization on the susceptibility to intergranular corrosion in AA5083 aluminum alloy: Effect of low temperature sensitization in AA5083 aluminum alloy
journal, October 2015

Heterogeneous distributions of Magnesium atoms near the precipitate in Al-Mg based alloys
journal, February 1995

Monitoring the precipitation reactions in a cold-rolled Al–Mn–Mg–Cu alloy using thermoelectric power and electrical resistivity measurements
journal, August 2001

Mechanism of intergranular corrosion of Al-Cu alloys
journal, January 1970

Stress corrosion cracking susceptibility of ultrafine grained Al–Mg–Sc alloy
journal, March 2013

Mass-Transport-Limited Oxygen Reduction Reaction on AA2024-T3 and Selected Intermetallic Compounds in Chromate-Containing Solutions
journal, February 2001

Hydrogen effects during IGSCC of pure Al–5Mg alloy in NaCl media
journal, June 2002

Rotating cage and jet impingement techniques
book, January 2008

Influence of Mg Content on the Sensitization and Corrosion of Al-xMg(-Mn) Alloys
journal, November 2013

Evaluation of Al3Mg2 Precipitates and Mn-Rich Phase in Aluminum-Magnesium Alloy Based on Scanning Transmission Electron Microscopy Imaging
journal, August 2012

Tem-studies of grain boundaries in cyclically deformed AlZnMg-bicrystals
journal, September 1992

Stress-corrosion cracking susceptibility of the superplastically formed 5083 aluminum alloy in 3.5 pct NaCl solution
journal, December 1999

The role of magnesium segregation in the intergranular stress corrosion cracking of aluminium alloys
journal, January 1987

Corrosion Behavior of Nanocrystalline Bulk Al-Mg-Based Alloys
journal, April 2004

The Degradation of Corrosion Resistance for Al 5083 Alloy after Thermal and Superplastic Forming Processes
journal, June 2000

Direct visualization of β phase causing intergranular forms of corrosion in Al–Mg alloys
journal, June 2013

Effects of Zn additions on the grain boundary precipitation and corrosion of Al-5083
journal, January 2000

The Ageing and Thermal Recovery Behaviour of Al-Mg-Cu Alloys
journal, July 2002

The Effect of Grain-Boundary Structure Formation on β-Precipitation in Aged Al-Mg Alloys
journal, November 1998

Transmission Electron Microscopic Investigations of Grain Boundary Beta Phase Precipitation in Al 5083 Aged at 373 K (100 °C)
journal, May 2012

Stress corrosion cracking susceptibility of Al–Mg alloy sheet with high Mg content
journal, September 2002

Determination of the β Solvus Temperature of the Aluminum Alloy 5083
journal, June 2013

Precipitation at grain boundaries in the commercial alloy Al 7075
journal, December 1986

Grain boundary misorientation dependence of β phase precipitation in an Al–Mg alloy
journal, April 2014

Stress corrosion cracking of sensitized AA5083 (Al-4.5Mg-1.0Mn)
journal, November 2001