Evaluation of an Al-Ce alloy for laser additive manufacturing
Abstract
Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min). The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.
- Authors:
-
- Univ. of Tennessee, Knoxville, TN (United States). Dept. of Mechanical Aerospace and Biomedical Engineering
- Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility and Materials Science and Technology Division
- Univ. of Tennessee, Knoxville, TN (United States). Bredesen Center for Interdisciplinary Research
- Ames Lab., Ames, IA (United States). Divison of Materials Science and Engineering
- (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility and Energy and Transportation Science Division
- Publication Date:
- Research Org.:
- Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States). High Temperature Materials Lab. (HTML); Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility (MDF)
- Sponsoring Org.:
- USDOE
- OSTI Identifier:
- 1347317
- Alternate Identifier(s):
- OSTI ID: 1397786
- Grant/Contract Number:
- AC05-00OR22725
- Resource Type:
- Accepted Manuscript
- Journal Name:
- Acta Materialia
- Additional Journal Information:
- Journal Volume: 126; Journal Issue: C; Journal ID: ISSN 1359-6454
- Publisher:
- Elsevier
- Country of Publication:
- United States
- Language:
- English
- Subject:
- 36 MATERIALS SCIENCE; Additive manufacturing; Al alloys; Microstructure control; Microstructure modeling
Citation Formats
Plotkowski, A., Rios, O., Sridharan, N., Sims, Z., Unocic, K., Ott, R. T., Dehoff, R. R., Babu, S. S., and Oak Ridge National Lab. Evaluation of an Al-Ce alloy for laser additive manufacturing. United States: N. p., 2016.
Web. doi:10.1016/j.actamat.2016.12.065.
Plotkowski, A., Rios, O., Sridharan, N., Sims, Z., Unocic, K., Ott, R. T., Dehoff, R. R., Babu, S. S., & Oak Ridge National Lab. Evaluation of an Al-Ce alloy for laser additive manufacturing. United States. https://doi.org/10.1016/j.actamat.2016.12.065
Plotkowski, A., Rios, O., Sridharan, N., Sims, Z., Unocic, K., Ott, R. T., Dehoff, R. R., Babu, S. S., and Oak Ridge National Lab. Tue .
"Evaluation of an Al-Ce alloy for laser additive manufacturing". United States. https://doi.org/10.1016/j.actamat.2016.12.065. https://www.osti.gov/servlets/purl/1347317.
@article{osti_1347317,
title = {Evaluation of an Al-Ce alloy for laser additive manufacturing},
author = {Plotkowski, A. and Rios, O. and Sridharan, N. and Sims, Z. and Unocic, K. and Ott, R. T. and Dehoff, R. R. and Babu, S. S. and Oak Ridge National Lab.},
abstractNote = {Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min). The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.},
doi = {10.1016/j.actamat.2016.12.065},
journal = {Acta Materialia},
number = C,
volume = 126,
place = {United States},
year = {Tue Dec 27 00:00:00 EST 2016},
month = {Tue Dec 27 00:00:00 EST 2016}
}
Web of Science
Works referenced in this record:
The metallurgy and processing science of metal additive manufacturing
journal, March 2016
- Sames, W. J.; List, F. A.; Pannala, S.
- International Materials Reviews, Vol. 61, Issue 5
Printability of alloys for additive manufacturing
journal, January 2016
- Mukherjee, T.; Zuback, J. S.; De, A.
- Scientific Reports, Vol. 6, Issue 1
Cerium-Based, Intermetallic-Strengthened Aluminum Casting Alloy: High-Volume Co-product Development
journal, May 2016
- Sims, Zachary C.; Weiss, D.; McCall, S. K.
- JOM, Vol. 68, Issue 7
Thermo-Calc & DICTRA, computational tools for materials science
journal, June 2002
- Andersson, J-O; Helander, Thomas; Höglund, Lars
- Calphad, Vol. 26, Issue 2
Correlation between mechanical properties and amount of dendritic α-Al phase in as-cast near-eutectic Al–11.6% Si alloys modified with strontium
journal, September 2002
- Liao, Hengcheng; Sun, Yu; Sun, Guoxiong
- Materials Science and Engineering: A, Vol. 335, Issue 1-2
Temperature effects on the tensile properties of cast and heat treated aluminum alloy A319
journal, August 2009
- Rincon, E.; Lopez, H. F.; Cisneros, M. M.
- Materials Science and Engineering: A, Vol. 519, Issue 1-2
Metal Additive Manufacturing: A Review
journal, April 2014
- Frazier, William E.
- Journal of Materials Engineering and Performance, Vol. 23, Issue 6
Additive manufacturing of nickel-based superalloy Inconel 718 by selective electron beam melting: Processing window and microstructure
journal, August 2014
- Helmer, Harald Ernst; Körner, Carolin; Singer, Robert Friedrich
- Journal of Materials Research, Vol. 29, Issue 17
Microstructural and texture development in direct laser fabricated IN718
journal, March 2014
- Parimi, Lakshmi L.; A., Ravi G.; Clark, Daniel
- Materials Characterization, Vol. 89
Crystallographic texture engineering through novel melt strategies via electron beam melting: Inconel 718
journal, October 2014
- Dehoff, R. R.; Kirka, M. M.; List, F. A.
- Materials Science and Technology, Vol. 31, Issue 8
Theory of microstructural development during rapid solidification
journal, May 1986
- Kurz, W.; Giovanola, B.; Trivedi, R.
- Acta Metallurgica, Vol. 34, Issue 5
Eutectic growth under rapid solidification conditions
journal, December 1991
- Kurz, W.; Trivedi, R.
- Metallurgical Transactions A, Vol. 22, Issue 12
Analysis of solidification microstructures in Fe-Ni-Cr single-crystal welds
journal, June 1990
- Rappaz, M.; David, S. A.; Vitek, J. M.
- Metallurgical Transactions A, Vol. 21, Issue 6
Banded solidification microstructures
journal, March 1996
- Kurz, W.; Trivedi, R.
- Metallurgical and Materials Transactions A, Vol. 27, Issue 3
The microstructure of rapidly solidified AlFe alloys subjected to laser surface treatment
journal, December 1990
- Gremaud, M.; Carrard, M.; Kurz, W.
- Acta Metallurgica et Materialia, Vol. 38, Issue 12
Rapid solidification of Al-Cu eutectic alloy by laser remelting
journal, December 1989
- Zimmermann, M.; Carrard, M.; Kurz, W.
- Acta Metallurgica, Vol. 37, Issue 12
Theory of eutectic growth under rapid solidification conditions
journal, April 1987
- Trivedi, R.; Magnin, P.; Kurz, W.
- Acta Metallurgica, Vol. 35, Issue 4
Model for solute redistribution during rapid solidification
journal, February 1982
- Aziz, M. J.
- Journal of Applied Physics, Vol. 53, Issue 2
Continuous growth model for interface motion during alloy solidification
journal, August 1988
- Aziz, Michael J.; Kaplan, Theodore
- Acta Metallurgica, Vol. 36, Issue 8
Dendritic growth
journal, January 1994
- Trivedi, R.; Kurz, W.
- International Materials Reviews, Vol. 39, Issue 2
The .DELTA. to .GAMMA. Transition in Fe-Cr-Ni Alloys during Laser Treatment.
journal, January 1997
- Fukumoto, Shigeo; Kurz, Wilfried
- ISIJ International, Vol. 37, Issue 7
Stability effects in dendritic crystal growth
journal, December 1977
- Langer, J. S.; Müller-Krumbhaar, J.
- Journal of Crystal Growth, Vol. 42
Theory of dendritic growth—I. Elements of a stability analysis
journal, November 1978
- Langer, J. S.; Müller-Krumbhaar, H.
- Acta Metallurgica, Vol. 26, Issue 11
Selection of steady states in the two-dimensional symmetric model of dendritic growth
journal, April 1986
- Meiron, Daniel I.
- Physical Review A, Vol. 33, Issue 4
Velocity selection in the symmetric model of dendritic crystal growth
journal, February 1987
- Barbieri, Angelo; Hong, Daniel C.; Langer, J. S.
- Physical Review A, Vol. 35, Issue 4
Stability of Dendritic Crystals
journal, December 1986
- Kessler, David A.; Levine, Herbert
- Physical Review Letters, Vol. 57, Issue 24
Orientation selection in dendritic evolution
journal, July 2006
- Haxhimali, Tomorr; Karma, Alain; Gonzales, Frédéric
- Nature Materials, Vol. 5, Issue 8
Approximation for the exponential integral (Theis well function)
journal, January 2000
- Barry, D. A.; Parlange, J. -Y; Li, L.
- Journal of Hydrology, Vol. 227, Issue 1-4
Works referencing / citing this record:
Cerium in aluminum alloys
journal, August 2019
- Czerwinski, Frank
- Journal of Materials Science, Vol. 55, Issue 1
Microstructure and mechanical properties of a novel selective laser melted Al–Mg alloy with low Sc content
journal, December 2019
- Churyumov, A. Yu; Pozdniakov, A. V.; Prosviryakov, A. S.
- Materials Research Express, Vol. 6, Issue 12
Microstructure and Properties of Novel Heat Resistant Al–Ce–Cu Alloy for Additive Manufacturing
journal, November 2018
- Manca, D. R.; Churyumov, A. Yu.; Pozdniakov, A. V.
- Metals and Materials International, Vol. 25, Issue 3
Design, analysis and manufacturing of lattice structures: an overview
journal, December 2017
- Helou, Mark; Kara, Sami
- International Journal of Computer Integrated Manufacturing, Vol. 31, Issue 3
A state-of-the-art review on types, design, optimization, and additive manufacturing of cellular structures
journal, July 2019
- Nazir, Aamer; Abate, Kalayu Mekonen; Kumar, Ajeet
- The International Journal of Advanced Manufacturing Technology, Vol. 104, Issue 9-12
Ultra high power (100 kW) fiber laser welding of steel
journal, January 2018
- Kawahito, Yousuke; Wang, Hongze; Katayama, Seiji
- Optics Letters, Vol. 43, Issue 19
Ageless Aluminum-Cerium-Based Alloys in High-Volume Die Casting for Improved Energy Efficiency
journal, April 2018
- Stromme, Eric T.; Henderson, Hunter B.; Sims, Zachary C.
- JOM, Vol. 70, Issue 6
The mechanism of eutectic modification by trace impurities
journal, March 2019
- Moniri, Saman; Xiao, Xianghui; Shahani, Ashwin J.
- Scientific Reports, Vol. 9, Issue 1
Microstructure and Mechanical Properties of Al-12Si Alloys Fabricated by Ultrasonic-Assisted Laser Metal Deposition
journal, December 2019
- Zhang, Yang; Guo, Yuqi; Chen, Yan
- Materials, Vol. 13, Issue 1