The Impact of Furnace-Testing on the Microstructure of an Irradiated U-Mo Fuel Plate
- Idaho National Laboratory, P. O. Box 1625, Idaho Falls, ID, 83403 (United States)
The Material Management and Minimization Program (formerly known as the Reduced Enrichment for Research and Test Reactor Program) is responsible for converting research reactors that use highly enriched uranium (HEU) fuels to ones that use low-enriched uranium (LEU) fuels. As part of the development of LEU fuels, a variety of irradiation experiments are being conducted using the Advanced Test Reactor. In addition to the reactor tests, there is interest in generating information about the transient behavior of irradiated fuel plates. For example, it is of interest to determine the temperature at which a blister will form on the surface of a fuel plate, due to fission gas release from the fuel meat, for a particular fuel plate design. Since in-pile testing to determine the 'blister threshold' (the temperature where a blister forms on the surface of a fuel plate) in plate-type fuel is very difficult and expensive and has historically been deemed impractical for fuel qualification testing, an out-of-pile 'blister test' has been developed and employed. This post-irradiation blister anneal test was developed as a conservative simulation of in-pile behavior and has been routinely used for many research reactor fuel designs currently in use. In this test, the irradiated fuel plate is inserted into a furnace at a given temperature, soaked for a period of time, and removed for inspection. If no visible blisters appear, the furnace temperature is increased, and the plate is soaked and inspected again. This process continues until blisters are observed. Recently, a section from an irradiated U-7Mo dispersion fuel plate with Al-4043 matrix, which has a nominal composition of 4.81Si-0.20Fe-0.14Ti-0.16Cu-0.01Cr 0.01Mn-bal Al, was tested in a furnace located in the Hot Fuel Examination Facility, located at the Idaho National Laboratory, up to 500 deg. C, at which point blisters were observed on the surface of the fuel plate section. A sample near the blistered region of the fuel plate section was then characterized using scanning electron (SEM) and transmission electron microscopy (TEM). This paper discusses the results of this characterization and how they compare to those generated for a similar sample characterized after fabrication but before irradiation and for a sample characterized after irradiation but before furnace testing. One goal of this work is to identify the changes in the microstructure during blister testing that contribute to the eventual release of fission gas that results in the development of blisters. SEM analysis of the furnace-tested sample showed that in some locations of the U-7Mo particles, Al-4043 matrix constituents (primarily Si) had penetrated the microstructure along grain boundaries. This provided potential pathways for increased fission gas migration in the fuel meat microstructure during the furnace heating process. Some attack of these boundaries was also observed in the as-fabricated U-7Mo/Al-4043 sample, but there appeared to be additional attack during the furnace annealing. Besides the changes observed in grain boundary features, the TEM analysis showed that the fission gas bubbles that are typically present in the intra-granular regions of the as-irradiated U-7Mo microstructure as a fission gas bubble superlattice had changed in size, morphology, and distribution. The result of this may be an increase in the mobility of the fission gas in intra-granular regions of the fuel. The complete implications of the changes in fission gas morphology and distribution in the fuel meat microstructure and their impact on blistering continues to be investigated. (authors)
- OSTI ID:
- 22992164
- Journal Information:
- Transactions of the American Nuclear Society, Vol. 114, Issue 1; Conference: Annual Meeting of the American Nuclear Society. Embedded topical meeting 'Nuclear fuels and structural material for the next generation nuclear reactors', New Orleans, LA (United States), 12-16 Jun 2016; Other Information: Country of input: France; 2 refs.; Available from American Nuclear Society - ANS, 555 North Kensington Avenue, La Grange Park, IL 60526 United States; ISSN 0003-018X
- Country of Publication:
- United States
- Language:
- English
Similar Records
TEM Characterization of U-Mo Irradiated with High-Energy Xe Ions
TEM Characterization of High Burn-up Microstructure of U-7Mo Alloy
Related Subjects
36 MATERIALS SCIENCE
ANNEALING
DISPERSION NUCLEAR FUELS
ELECTRON SCANNING
FISSION
FISSION PRODUCT RELEASE
FISSION PRODUCTS
FUEL PLATES
GRAIN BOUNDARIES
HIGHLY ENRICHED URANIUM
IRRADIATION
MINIMIZATION
RESEARCH REACTORS
SCANNING ELECTRON MICROSCOPY
SPENT FUELS
TEST REACTORS
TRANSMISSION ELECTRON MICROSCOPY