Thermal impact of adhesive-mounted rooftop PV on underlying roof shingles

Shukla, Nitin; Watts, Alliston; Honeker, Christian; Hill, Mark; Kośny, Jan

doi:10.1016/j.solener.2018.09.079

Thermal impact of adhesive-mounted rooftop PV on underlying roof shingles

Journal Article · Wed Oct 03 00:00:00 EDT 2018 · Solar Energy

DOI:https://doi.org/10.1016/j.solener.2018.09.079· OSTI ID:1613328

Shukla, Nitin ^[1]; Watts, Alliston ^[2]; Honeker, Christian ^[2]; Hill, Mark ^[2]; Kośny, Jan ^[2]

Fraunhofer Center for Sustainable Energy Systems CSE, Boston, MA (United States); DOE/OSTI
Fraunhofer Center for Sustainable Energy Systems CSE, Boston, MA (United States)

Adhesive mounting of residential rooftop photovoltaics (PV) is an alternative to traditional rack mounting that reduces installation costs. Adhesive mounting is fast, simple and reduces the need for skilled labor. In our novel design that further reduces the installation costs, a lightweight (glassless and frameless) PV module is directly adhered to a shingled roof using an adhesive tape, creating a <5 mm air gap between the PV back-panel and the roof shingle surface. Although the gap is sufficient for moisture and rainwater transport under the PV panel, potential heat buildup under the module may adversely impact the long-term durability of the shingles. Heat buildup may also increase the heat flux through the roof, resulting in an overall increase in building cooling loads. This study investigates the thermal behavior of the roof under an adhered PV system. Two identical test huts with dark shingle-covered roofs were located in the hot, desert climate of Albuquerque, NM. Adhesively-mounted lightweight PV modules were installed on the south-facing roof of one of the test huts (PV hut), with the other one serving as a reference hut. During the summer season, the asphalt roof shingles under the PV modules experienced a 13 °C reduction in daytime peak temperature compared with the exposed shingles. No evidence of heat buildup under the PV module was observed. It was also found that the temperature of shingles underneath the adhesive was up to 6 °C higher than for shingles underneath the gap space at the daily peak time. Thin but ventilated air gap between the PV back-panel and the roof shingles helped remove the heat, while the adhesive pads (patches) served as thermal bridges between the PV module and the roof. Daily peak heat flow through the attic ceiling was almost 49% lower in the PV hut compared to the reference hut. These results show no evidence of an adverse thermal impact of the adhesive-mounted PV system on the roofing materials, while demonstrating a potential for a notable reduction in space conditioning energy requirements.

Research Organization:: Fraunhofer Center for Sustainable Energy Systems CSE, Boston, MA (United States)

Sponsoring Organization:: USDOE Office of Energy Efficiency and Renewable Energy (EERE), Renewable Power Office. Solar Energy Technologies Office

Grant/Contract Number:: EE0006035

OSTI ID:: 1613328

Alternate ID(s):: OSTI ID: 1636035

Journal Information:: Solar Energy, Journal Name: Solar Energy Vol. 174; ISSN 0038-092X

Publisher:: ElsevierCopyright Statement

Country of Publication:: United States

Language:: English

References (13)

New configurations of a roof solar collector maximizing natural ventilation Hirunlabh, Jongjit; Wachirapuwadon, Sopin; Pratinthong, Naris Building and Environment, Vol. 36, Issue 3 https://doi.org/10.1016/S0360-1323(00)00016-0	journal	April 2001
Ventilated-solar roof air flow and heat transfer investigation Sandberg, Mats; Moshfegh, Bahram Renewable Energy, Vol. 15, Issue 1-4 https://doi.org/10.1016/S0960-1481(98)00175-X	journal	September 1998
Flow and heat transfer in the air gap behind photovoltaic panels Moshfegh, B.; Sandberg, M. Renewable and Sustainable Energy Reviews, Vol. 2, Issue 3 https://doi.org/10.1016/S1364-0321(98)00005-7	journal	September 1998
Effect of building integrated photovoltaics on microclimate of urban canopy layer Tian, Wei; Wang, Yiping; Xie, Yiyang Building and Environment, Vol. 42, Issue 5 https://doi.org/10.1016/j.buildenv.2006.02.022	journal	May 2007
Weathering of roofing materials – An overview Berdahl, Paul; Akbari, Hashem; Levinson, Ronnen Construction and Building Materials, Vol. 22, Issue 4, p. 423-433 https://doi.org/10.1016/j.conbuildmat.2006.10.015	journal	April 2008
Temperature Dependent Photovoltaic (PV) Efficiency and Its Effect on PV Production in the World – A Review Dubey, Swapnil; Sarvaiya, Jatin Narotam; Seshadri, Bharath Energy Procedia, Vol. 33 https://doi.org/10.1016/j.egypro.2013.05.072	journal	January 2013
A nodal thermal model for photovoltaic systems: Impact on building temperature fields and elements of validation for tropical and humid climatic conditions Bigot, D.; Miranville, F.; Fakra, A. H. Energy and Buildings, Vol. 41, Issue 11 https://doi.org/10.1016/j.enbuild.2009.06.009	journal	November 2009
Design procedure for cooling ducts to minimise efficiency loss due to temperature rise in PV arrays Brinkworth, B. J.; Sandberg, M. Solar Energy, Vol. 80, Issue 1 https://doi.org/10.1016/j.solener.2005.05.020	journal	January 2006
Numerical determination of adequate air gaps for building-integrated photovoltaics Gan, Guohui Solar Energy, Vol. 83, Issue 8 https://doi.org/10.1016/j.solener.2009.02.008	journal	August 2009
Equilibrium thermal characteristics of a building integrated photovoltaic tiled roof Mei, L.; Infield, D. G.; Gottschalg, R. Solar Energy, Vol. 83, Issue 10 https://doi.org/10.1016/j.solener.2009.07.002	journal	October 2009
Effects of solar photovoltaic panels on roof heat transfer Dominguez, Anthony; Kleissl, Jan; Luvall, Jeffrey C. Solar Energy, Vol. 85, Issue 9 https://doi.org/10.1016/j.solener.2011.06.010	journal	September 2011
Effect of mounting geometry on convection occurring under a photovoltaic panel and the corresponding efficiency using CFD Wilson, Michael J.; Paul, Manosh C. Solar Energy, Vol. 85, Issue 10 https://doi.org/10.1016/j.solener.2011.07.013	journal	October 2011
Field thermal performance of naturally ventilated solar roof with PCM heat sink Kośny, Jan; Biswas, Kaushik; Miller, William Solar Energy, Vol. 86, Issue 9 https://doi.org/10.1016/j.solener.2012.05.020	journal	September 2012

Similar Records

Lightweight flexible rooftop PV module

Conference · Fri Dec 30 23:00:00 EST 1994 · OSTI ID:208228

A new type of photovoltaic shingle

Conference · Fri Dec 30 23:00:00 EST 1994 · OSTI ID:208232

Solar heating shingle roof structure

Patent · Mon Jan 30 23:00:00 EST 1984 · OSTI ID:7075512

Related Subjects

14 SOLAR ENERGY
Building Integrated Photovoltaic (BIPV)
adhesive-mounting of PV
thermal impact of PV on roof

Thermal impact of adhesive-mounted rooftop PV on underlying roof shingles

Citation Formats

References (13)

Similar Records

Related Subjects