Validation of Numerical Models of the Offshore Wind Turbine from the Alpha Ventus Wind Farm Against Full-Scale Measurements Within OC5 Phase III: Preprint

Conference · Tue May 14 00:00:00 EDT 2019

OSTI ID:1514827

Popko, Wojciech ^[1]; Robertson, Amy N  ^[2]; Jonkman, Jason  ^[2]; Wendt, Fabian F ^[2]; Thomas, Philipp ^[1]; Muller, Kolja ^[3]; Kretschmer, Matthias ^[3]; Hagen, Torbjorn R ^[4]; Galinos, Christos ^[5]; Le Dreff, Jean-Baptiste ^[6]; Gilbert, Philippe ^[7]; Auriac, Bertrand ^[8]; Oh, Sho ^[9]; Qvist, Jacob ^[10]; Sorum, Stian H ^[11]; Suja-Thauvin, Loup ^[12]; Shin, Hyunkyoung ^[13]; Molins, Climent ^[14]; Truba, Pau ^[14]; Bonnet, Paul ^[15] ; Bergua, Roger ^[16]; Wang, Kai ^[16]; Fu, Pengcheng ^[17]; Cai, Jifeng ^[17]; Cai, Zhisong ^[17]; Alexandre, Armando ^[18]; Harries, Robert ^[18]

---

1. Fraunhofer Institute for Wind Energy Systems
2. National Renewable Energy Laboratory (NREL), Golden, CO (United States)
3. University of Stuttgart
4. 4OWEC Tower AS
5. Technical University of Denmark
6. Electricite de France
7. IFP Energies Nouvelles
8. Principia
9. Nippon Kaiji Kyokai
10. 4Subsea
11. Norwegian University of Science and Technology
12. Simis AS
13. University of Ulsan
14. Polytechnic University of Catalonia
15. Siemens Industry Software
16. Envision Energy Limited
17. China General Certification Center
18. DNV GL

The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project, is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison of simulated results to the response data of physical systems. Phase III of the OC5 project validates OWT models against the measurements recorded on Senvion 5M wind turbine supported by the OWEC Quattropod from the alpha ventus offshore wind farm. The following operating conditions of the wind turbine were chosen for the validation: (1) Idling below the cut-in wind speed; (2) Rotornacelle assembly (RNA) rotation maneuver below the cut-in wind speed; (3) Power production below and above the rated wind speed; and (4) Shut-down. A number of validation load cases were defined based on these operating conditions. The following measurements were used for validation: (1) Strains and accelerations recorded on the support structure; (2) Pitch, yaw, and azimuth angles, generator speed, and electrical power recorded from the RNA. Strains were not directly available from the majority of the OWT simulation tools. Therefore, strains were calculated based on out-of-plane bending moments, axial forces, and geometrical properties of the structural members. Also, a number of issues arose during the validation: (1) The need for a thorough quality check of sensor measurements; (2) The sensitivity of the turbine loads to the controller and airfoil properties, which were only approximated in the modeling approach; (3) The importance of estimating and applying an appropriate damping value for the structure; and (4) The importance of wind characteristics beyond turbulence on the loads. The simulation results and measurements were compared in terms of time series, discrete Fourier transforms (DFTs), power spectral densities (PSDs), probability density functions (PDFs) of strains and accelerometers. A good match was achieved between the measurements and models set up by OC5 Phase III participants.

• Research Organization: National Renewable Energy Lab. (NREL), Golden, CO (United States)
• Sponsoring Organization: USDOE Office of Energy Efficiency and Renewable Energy (EERE), Wind and Water Technologies Office (EE-4W)
• DOE Contract Number: AC36-08GO28308
• OSTI ID: 1514827
• Report Number(s): NREL/CP-5000-73191
• Resource Relation: Conference: Presented at the ASME 2019 38th Annual Conference on Ocean, Offshore, and Arctic Engineering, 9-14 June 2019, Glasgow, Scotland
• Country of Publication: United States
• Language: English

Related Subjects

17 WIND ENERGY
offshore wind
full-scale measurements
validation
ventus
jacket