Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ
Abstract
Our group has recently developed and studied “finger”-type divertors that are a simplified version of the helium-cooled modular divertor with multiple jets (HEMJ) using coupled computational fluid dynamics and thermal stress simulations. Such a simplified geometry could reduce complexity and cost given the large number of fingers required to cover the total divertor target area. Previous experimental studies for this simplified flat design reported lower heat transfer coefficients and higher pressure drops than the HEMJ, contrary to numerical predictions. Subsequent measurements determined that the original test section had significant dimensional variations in the jet exit holes. A new test section was therefore manufactured and tested in the Georgia Tech (GT) helium loop. The experimental results presented here for this test section at maximum heat flux of 7.1 MW/m2 are in good agreement with numerical predictions. Correlations developed from these experimental data are extrapolated to predict the maximum heat flux that can be accommodated by the flat design and the coolant pumping power requirements under prototypical conditions. Lastly, numerical simulations are used to estimate the sensitivity of the flat design to geometric variations typical of manufacturing tolerances and variations in the gap width.
- Authors:
-
- Georgia Institute of Technology, Atlanta, GA (United States)
- Publication Date:
- Research Org.:
- Georgia Institute of Technology, Atlanta, GA (United States)
- Sponsoring Org.:
- USDOE Office of Science (SC), Fusion Energy Sciences (FES)
- OSTI Identifier:
- 1830542
- Grant/Contract Number:
- FG02-01ER54656
- Resource Type:
- Accepted Manuscript
- Journal Name:
- Fusion Science and Technology
- Additional Journal Information:
- Journal Volume: 77; Journal Issue: 8; Conference: American Nuclear Society Technology of Fusion Energy Meeting (TOFE 2020), Virtual, 15-19 Nov 2020; Journal ID: ISSN 1536-1055
- Publisher:
- American Nuclear Society
- Country of Publication:
- United States
- Language:
- English
- Subject:
- 70 PLASMA PHYSICS AND FUSION TECHNOLOGY; thermofluids; divertor; helium-cooled modular divertor with multiple jets
Citation Formats
Lee, D. S., Musa, S. A., Abdel-Khalik, S. I., and Yoda, M. Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ. United States: N. p., 2021.
Web. doi:10.1080/15361055.2021.1920783.
Lee, D. S., Musa, S. A., Abdel-Khalik, S. I., & Yoda, M. Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ. United States. https://doi.org/10.1080/15361055.2021.1920783
Lee, D. S., Musa, S. A., Abdel-Khalik, S. I., and Yoda, M. Mon .
"Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ". United States. https://doi.org/10.1080/15361055.2021.1920783. https://www.osti.gov/servlets/purl/1830542.
@article{osti_1830542,
title = {Updated Thermofluid Performance of the Simplified Flat Variant of the HEMJ},
author = {Lee, D. S. and Musa, S. A. and Abdel-Khalik, S. I. and Yoda, M.},
abstractNote = {Our group has recently developed and studied “finger”-type divertors that are a simplified version of the helium-cooled modular divertor with multiple jets (HEMJ) using coupled computational fluid dynamics and thermal stress simulations. Such a simplified geometry could reduce complexity and cost given the large number of fingers required to cover the total divertor target area. Previous experimental studies for this simplified flat design reported lower heat transfer coefficients and higher pressure drops than the HEMJ, contrary to numerical predictions. Subsequent measurements determined that the original test section had significant dimensional variations in the jet exit holes. A new test section was therefore manufactured and tested in the Georgia Tech (GT) helium loop. The experimental results presented here for this test section at maximum heat flux of 7.1 MW/m2 are in good agreement with numerical predictions. Correlations developed from these experimental data are extrapolated to predict the maximum heat flux that can be accommodated by the flat design and the coolant pumping power requirements under prototypical conditions. Lastly, numerical simulations are used to estimate the sensitivity of the flat design to geometric variations typical of manufacturing tolerances and variations in the gap width.},
doi = {10.1080/15361055.2021.1920783},
journal = {Fusion Science and Technology},
number = 8,
volume = 77,
place = {United States},
year = {Mon Sep 27 00:00:00 EDT 2021},
month = {Mon Sep 27 00:00:00 EDT 2021}
}
Works referenced in this record:
European divertor target concepts for DEMO: Design rationales and high heat flux performance
journal, August 2018
- You, J. H.; Visca, E.; Barrett, T.
- Nuclear Materials and Energy, Vol. 16
He-cooled divertor for DEMO: Status of development and HHF tests
journal, December 2010
- Norajitra, Prachai; Giniyatulin, Radmir; Kuznetsov, Vladimir
- Fusion Engineering and Design, Vol. 85, Issue 10-12
Thermal Hydraulics of Helium-Cooled Finger-Type Divertors at Higher Incident Heat Fluxes
journal, May 2019
- Lee, D. S.; Musa, S. A.; Abdel-Khalik, S. I.
- Fusion Science and Technology, Vol. 75, Issue 8
Experimental and numerical studies of helium-cooled modular divertors with multiple jets
journal, November 2018
- Zhao, Bailey; Musa, Shekaib; Abdel-Khalik, Said
- Fusion Engineering and Design, Vol. 136
Optimum jet-to-jet spacing of heat transfer for staggered arrays of impinging air jets
journal, November 2001
- San, Jung-Yang; Lai, Mao-De
- International Journal of Heat and Mass Transfer, Vol. 44, Issue 21
The use of water in a fusion power core
journal, February 2015
- Tillack, M. S.; Humrickhouse, P. W.; Malang, S.
- Fusion Engineering and Design, Vol. 91
Experimental Evaluation of the Thermal Hydraulics of Helium-Cooled Divertors
journal, January 2015
- Yoda, M.; Abdel-Khalik, S. I.; Sadowski, D. L.
- Fusion Science and Technology, Vol. 67, Issue 1
He-cooled divertor development for DEMO
journal, October 2007
- Norajitra, P.; Giniyatulin, R.; Ihli, T.
- Fusion Engineering and Design, Vol. 82, Issue 15-24
Recent US activities on advanced He-cooled W-alloy divertor concepts for fusion power plants
journal, January 2011
- Tillack, M. S.; Raffray, A. R.; Wang, X. R.
- Fusion Engineering and Design, Vol. 86, Issue 1
Eurofusion-DEMO Divertor - Cassette Design and Integration
journal, August 2020
- Mazzone, Giuseppe; You, Jeong-Ha; Bachmann, Christian
- Fusion Engineering and Design, Vol. 157
An Experimental Study of the Helium-Cooled Modular Divertor with Multiple Jets at Nearly Prototypical Conditions
journal, October 2015
- Mills, B. H.; Zhao, B.; Abdel-Khali, S. I.
- Fusion Science and Technology, Vol. 68, Issue 3