NOVEL PREPARATION AND MAGNETO CHEMICAL CHARACTERIZATION OF NANOPARTICLE MIXED ALCOHOL CATALYSTS
We have developed and streamlined the experimental systems: (a) Laser-induced solution deposition (LISD) photosynthesis, ball-milling, and chemical synthesis of Fe, Co, and Cu nanoparticle catalysts; (b) Sol-gel method for mesoporous {gamma}-Al{sub 2}O{sub 3}, SiO{sub 2}, hybrid alumina/silica granular supports; (c) Three sol-gel/oil-drop catalyst preparation methods to incorporate metal nanoparticles into mesoporous 1 mm granular supports; (d) Low-cost GC-TCD system with hydrogen as carrier gas for the determination of wide spectrum of alkanes produced during the F-T reactions; and (e) Gas-flow reactor and microchannel reactor for fast screening of catalysts. The LISD method could produce Co, Cu, and Fe (5 nm) nanoparticles, but in milligram quantities. We could produce nanoparticles in gram quantities using high-energy ball milling and chemical synthesis methods. Ball milling gave wide particle size distribution compared to the chemical synthesis method that gave almost uniform size ({approx}5 nm) particles. Metal nanoparticles Cu, Co, Fe, Cu/Co, Cu/Fe and Co/Fe were loaded (2-12 wt%) uniformly into {gamma}-Al{sub 2}O{sub 3}, SiO{sub 2}, or alumina/silica hybrid supports by combined sol-gel/oil-drop methods followed by calcination and hydrogenation steps, prior to syngas FT reaction studies. The properties of metal loaded {gamma}-Al{sub 2}O{sub 3} granules were compared for the two precursors: aluminum tri-sec-butoxide (ALTSB) and aluminum tri-iso-propoxide (ALTIP). The effect of solgel supports alumina, silica, and alumina/silica hybrid were examined on catalytic properties. Metal loading efficiencies for pure metal catalysts increased in the order Co, Cu and Fe in agreement with solubility of metal hydroxides. In case of mixed metals, Co and Cu seams to interfere and reduce Fe metal loading when metal nitrate solutions are used. The solubility differences of metal hydroxides would not allow precise control of metal loading. We have overcome this problem by introducing a novel method of nanoparticle metal oxide co-entrapped sol-gel that gave the highest metal loading with precise control and reproducibility, and greater mechanical strength of granules than the metal nitrate solution co-entrapping and wet impregnation methods. Both, slurry-phase-batch and gas-phase-continuous-flow, reactors were used for syngas conversion reactions. Our investigations of Co and Fe thin film deposited micro-reactors showed higher CO/H{sub 2} conversion for Fe compared to Co. The catalytic activity for CO/H{sub 2} conversion was observed in the increasing order for the nanocatalysts Cu, Co, Fe, Co/Fe, Cu/Co and Cu/Fe in alumina sol-gel support, and Co/Fe showed the highest yield for methane. The optimization of CO/H{sub 2} ratio indicated that 1:1 ratio gave more alkanes distribution in F-T process with Co/Fe (6% each) impregnated on alumina. We could estimate the activity of catalysts (involving Co, Fe) during hydrogenation and after catalytic reaction using magnetization studies. In summary our accomplishments are: (1) Novel chemical methods for the synthesis of (5 nm) Fe, Co, Cu nanoparticles with narrow size distribution. (2) Developing a method of metal oxide nanoparticles addition to alumina/silica sol-gel to control metal loading of pure and mixed metal catalysts compositions in high yields. (3) A low-cost GC-TCD system to analyze wide spectrum of alkanes (F-T reaction products). (4) Fe/Co mixed metal alumina/silica mesoporous catalysts with higher FT activity. (5) Characterizing nanoparticle catalysts and supports for detail understanding of FT-process.
- Research Organization:
- Grambling State University
- DOE Contract Number:
- FG26-00NT40836
- OSTI ID:
- 843081
- Country of Publication:
- United States
- Language:
- English
Similar Records
NOVEL PREPARATION AND MAGNETO CHEMICAL CHARACTERIZATION OF NANO-PARTICLE MIXED ALCOHOL CATALYSTS
NOVEL PREPARATION AND MAGNETO CHEMICAL CHARACTERIZATION OF NANO-PARTICLE MIXED ALCOHOL CATALYSTS