skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Failure analysis of beryllium tile assembles following high heat flux testing for the ITER program

Abstract

The following document describes the processing, testing and post-test analysis of two Be-Cu assemblies that have successfully met the heat load requirements for the first wall and dome sections for the ITER (International Thermonuclear Experimental Reactor) fusion reactor. Several different joint assemblies were evaluated in support of a manufacturing technology investigation aimed at diffusion bonding or brazing a beryllium armor tile to a copper alloy heat sink for fusion reactor applications. Judicious selection of materials and coatings for these assemblies was essential to eliminate or minimize interactions with the highly reactive beryllium armor material. A thin titanium layer was used as a diffusion barrier to isolate the copper heat sink from the beryllium armor. To reduce residual stresses produced by differences in the expansion coefficients between the beryllium and copper, a compliant layer of aluminum or aluminum-beryllium (AlBeMet-150) was used. Aluminum was chosen because it does not chemically react with, and exhibits limited volubility in, beryllium. Two bonding processes were used to produce the assemblies. The primary process was a diffusion bonding technique. In this case, undesirable metallurgical reactions were minimized by keeping the materials in a solid state throughout the fabrication cycle. The other process employed an aluminum-silicon layermore » as a brazing filler material. In both cases, a hot isostatic press (HIP) furnace was used in conjunction with vacuum-canned assemblies in order to minimize oxidation and provide sufficient pressure on the assemblies for full metal-to-metal contact and subsequent bonding. The two final assemblies were subjected to a suite of tests including: tensile tests and electron and optical metallography. Finally, high heat flux testing was conducted at the electron beam testing system (EBTS) at Sandia National Laboratories, New Mexico. Here, test mockups were fabricated and subjected to normal heat loads to 10 MW/m{sup 2} (3 Hz) and abnormal heat loads to 250 MJ/m{sup 2} (0.5s) to determine their performance under simulated fusion reactor conditions for first wall components. Both assemblies survived the normal heat loads with no visual damage. Optical and electron microscopy were used to evaluate the extent of the damage at the interfaces following the VDE simulations.« less

Authors:
; ;
Publication Date:
Research Org.:
Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sandia National Lab. (SNL-CA), Livermore, CA (United States)
Sponsoring Org.:
US Department of Energy (US)
OSTI Identifier:
756338
Report Number(s):
SAND99-8250
TRN: US0003798
DOE Contract Number:  
AC04-94AL85000
Resource Type:
Technical Report
Resource Relation:
Other Information: PBD: 1 May 2000
Country of Publication:
United States
Language:
English
Subject:
70 PLASMA PHYSICS AND FUSION TECHNOLOGY; ITER TOKAMAK; BERYLLIUM; COPPER; JOINTS; JOINING; HEAT SINKS; TITANIUM; THERMONUCLEAR REACTOR MATERIALS; ALUMINIUM; LAYERS; MATERIALS TESTING; FIRST WALL

Citation Formats

Odegard, Jr, B C, Cadden, C H, and C Yang, N Y. Failure analysis of beryllium tile assembles following high heat flux testing for the ITER program. United States: N. p., 2000. Web. doi:10.2172/756338.
Odegard, Jr, B C, Cadden, C H, & C Yang, N Y. Failure analysis of beryllium tile assembles following high heat flux testing for the ITER program. United States. https://doi.org/10.2172/756338
Odegard, Jr, B C, Cadden, C H, and C Yang, N Y. 2000. "Failure analysis of beryllium tile assembles following high heat flux testing for the ITER program". United States. https://doi.org/10.2172/756338. https://www.osti.gov/servlets/purl/756338.
@article{osti_756338,
title = {Failure analysis of beryllium tile assembles following high heat flux testing for the ITER program},
author = {Odegard, Jr, B C and Cadden, C H and C Yang, N Y},
abstractNote = {The following document describes the processing, testing and post-test analysis of two Be-Cu assemblies that have successfully met the heat load requirements for the first wall and dome sections for the ITER (International Thermonuclear Experimental Reactor) fusion reactor. Several different joint assemblies were evaluated in support of a manufacturing technology investigation aimed at diffusion bonding or brazing a beryllium armor tile to a copper alloy heat sink for fusion reactor applications. Judicious selection of materials and coatings for these assemblies was essential to eliminate or minimize interactions with the highly reactive beryllium armor material. A thin titanium layer was used as a diffusion barrier to isolate the copper heat sink from the beryllium armor. To reduce residual stresses produced by differences in the expansion coefficients between the beryllium and copper, a compliant layer of aluminum or aluminum-beryllium (AlBeMet-150) was used. Aluminum was chosen because it does not chemically react with, and exhibits limited volubility in, beryllium. Two bonding processes were used to produce the assemblies. The primary process was a diffusion bonding technique. In this case, undesirable metallurgical reactions were minimized by keeping the materials in a solid state throughout the fabrication cycle. The other process employed an aluminum-silicon layer as a brazing filler material. In both cases, a hot isostatic press (HIP) furnace was used in conjunction with vacuum-canned assemblies in order to minimize oxidation and provide sufficient pressure on the assemblies for full metal-to-metal contact and subsequent bonding. The two final assemblies were subjected to a suite of tests including: tensile tests and electron and optical metallography. Finally, high heat flux testing was conducted at the electron beam testing system (EBTS) at Sandia National Laboratories, New Mexico. Here, test mockups were fabricated and subjected to normal heat loads to 10 MW/m{sup 2} (3 Hz) and abnormal heat loads to 250 MJ/m{sup 2} (0.5s) to determine their performance under simulated fusion reactor conditions for first wall components. Both assemblies survived the normal heat loads with no visual damage. Optical and electron microscopy were used to evaluate the extent of the damage at the interfaces following the VDE simulations.},
doi = {10.2172/756338},
url = {https://www.osti.gov/biblio/756338}, journal = {},
number = ,
volume = ,
place = {United States},
year = {Mon May 01 00:00:00 EDT 2000},
month = {Mon May 01 00:00:00 EDT 2000}
}