The science, technology, and applications of magnesium
|
journal
|
September 1998 |
Influence of initial texture on rolling and annealing textures of Mg–3Al–1Zn alloy sheets processed by high temperature rolling
|
journal
|
October 2012 |
In situ X-ray diffraction and crystal plasticity modeling of the deformation behavior of extruded Mg–Li–(Al) alloys: An uncommon tension–compression asymmetry
|
journal
|
March 2015 |
Texture and stretch formability of AZ61 and AM60 magnesium alloy sheets processed by high-temperature rolling
|
journal
|
May 2015 |
Microstructure, texture and mechanical properties in an as-cast AZ61 Mg alloy during multi-directional impact forging and subsequent heat treatment
|
journal
|
December 2015 |
Microstructure, texture and mechanical properties of extruded Mg–5Al–2Nd–0.2Mn alloy
|
journal
|
December 2015 |
Enhanced ductility in strongly textured magnesium produced by equal channel angular processing
|
journal
|
February 2004 |
Anisotropy of the extruded and heat-treated Li containing AZ31 magnesium alloys
|
journal
|
March 2014 |
Microstructure, texture and mechanical properties of Mg-3.0Zn-0.2Ca alloys fabricated by extrusion at various temperatures
|
journal
|
December 2015 |
The relation between ductility and stacking fault energies in Mg and Mg–Y alloys
|
journal
|
April 2012 |
A high-specific-strength and corrosion-resistant magnesium alloy
|
journal
|
October 2015 |
Microstructures and properties of superlight Mg–Li–Al–Zn wrought alloys
|
journal
|
November 2009 |
Prediction of thermal cross-slip stress in magnesium alloys from a geometric interaction model
|
journal
|
March 2012 |
Application of texture simulation to understanding mechanical behavior of Mg and solid solution alloys containing Li or Y
|
journal
|
December 2001 |
Transmission electron microscopy investigation of 〈c+a〉 dislocations in Mg and α-solid solution Mg-Li alloys
|
journal
|
March 2002 |
Ductility improvement of Mg alloys by solid solution: Ab initio modeling, synthesis and mechanical properties
|
journal
|
May 2014 |
Study on edge cracking and texture evolution during 150°C rolling of magnesium alloys: The effects of axial ratio and grain size
|
journal
|
January 2012 |
The influences of alloying additions and processing parameters on the rolling microstructures and textures of magnesium alloys
|
journal
|
May 2008 |
Effect of Li content on the indentation creep characteristics of cast Mg–Li–Zn alloys
|
journal
|
June 2015 |
Evolution of microstructure and mechanical properties of a duplex Mg–Li alloy under extrusion with an increasing ratio
|
journal
|
May 2014 |
Recrystallization and texture evolution of cold-rolled AZ31 Mg alloy treated by rapid thermal annealing
|
journal
|
January 2016 |
Non-basal slip systems in HCP metals and alloys: source mechanisms
|
journal
|
December 2001 |
Textures and mechanical behavior of Mg–3.3%Li alloy after ECAP
|
journal
|
November 2004 |
The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys
|
journal
|
April 2003 |
Microstructural evolution during large strain hot rolling of an AM60 Mg alloy
|
journal
|
March 2004 |
Property improvements in fine–grained Mg–Zn–Zr alloy sheets produced by temperature–step–down multi–pass rolling
|
journal
|
October 2015 |
Cold rolling textures in AZ31 wrought magnesium alloy
|
journal
|
April 2004 |
Texture evolution of AZ31 magnesium alloy sheets during warm rolling
|
journal
|
October 2015 |
Texture Development in a Cold-Rolled and Annealed Body-Centered-Cubic Mg-Li Alloy
|
journal
|
August 2007 |
Numerical study on the effects of main BCC rolling texture components on the formability of sheet metals
|
journal
|
March 2015 |
The evolution of recrystallization textures in body centred cubic metals
|
journal
|
June 1998 |
Dynamic recrystallization during high temperature deformation of magnesium
|
journal
|
August 2008 |
Simulation of the Texture Evolution During Annealing of Cold Rolled Bcc and Fcc Metals Using a Cellular Automation Approach
|
journal
|
January 1997 |
Effect of competing hardening and softening mechanisms on the flow stress curve modeling of ultra-low carbon steel at high temperatures
|
journal
|
November 2003 |
A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization
|
journal
|
January 1996 |
Generalized stacking fault energy, ideal strength and twinnability of dilute Mg-based alloys: A first-principles study of shear deformation
|
journal
|
April 2014 |
Ab initio study of the effect of solute atoms Zn and Y on stacking faults in Mg solid solution
|
journal
|
May 2013 |
Texture Formation in Hexagonal Materials
|
journal
|
May 1994 |
The Effect of Shear Texture Development on the Formability in Rolled Aluminum Alloys Sheets
|
journal
|
February 1998 |