K Basin sludge/resin bead separation test report
The K Basin sludge is an accumulation of fuel element corrosion products, organic and inorganic ion exchange materials, canister gasket materials, iron and aluminum corrosion products, sand, dirt and minor amounts of other organic material. The sludge will be collected and treated for storage and eventual disposal. This process will remove the large solid materials by a 1/4 inch screen. The screened material will be subjected to nitric acid in a chemical treatment process. The organic ion exchange resin beads produce undesirable chemical reactions with the nitric acid. The resin beads must be removed from the bulk material and treated by another process. An effective bead separation method must extract 95% of the resin bead mass without entraining more than 5% of the other sludge component mass. The test plan I-INF-2729, ``Organic Ion Exchange Resin Separation Methods Evaluation,`` proposed the evaluation of air lift, hydro cyclone, agitated slurry and elutriation resin bead separation methods. This follows the testing strategy outlined in section 4.1 of BNF-2574, ``Testing Strategy to Support the Development of K Basins Sludge Treatment Process``. Engineering study BNF-3128, ``Separation of Organic Ion Exchange Resins from Sludge,`` Rev. 0, focused the evaluation tests on a method that removed the fine sludge particles by a sieve and then extracted the beads by means of a elutriation column. Ninety-nine percent of the resin beads are larger than 125 microns and 98.5 percent are 300 microns and larger. Particles smaller than 125 microns make up the largest portion of sludge in the K Basins. Eliminating a large part of the sludge`s non-bead component will reduce the quantity that is lifted with the resin beads in the elutriation column. Resin bead particle size distribution measurements are given in Appendix A The Engineering Testing Laboratory conducted measurements of a elutriation column`s ability to extract resin beads from a sieved, non-radioactive sludge simulant. A elutriation column uses a constant velocity upward flow stream to segregate materials. In simplistic terms, the dense particles fall to the column`s bottom while the flow lifts less dense particles to the column`s top. A particle can be streamlined or have a high drag profile; this factor also influences the lift or fall of a particle exposed to the column flow. The sludge components that lift or fall are determined by the fluid velocity. The column flow velocity needed to lift the bulk of the resin beads will also lift other, non-bead, sludge components. Resin bead treatment and disposal are complicated by large quantities of non-bead material. Tests are necessary to determine a column flow velocity that will collect the bulk of the resin beads and the amount of non-bead sludge components that are also collected.
- Research Organization:
- Fluor Daniel Hanford, Inc., Richland, WA (United States)
- Sponsoring Organization:
- USDOE Office of Environmental Restoration and Waste Management, Washington, DC (United States)
- DOE Contract Number:
- AC06-96RL13200
- OSTI ID:
- 10148510
- Report Number(s):
- HNF-3132; ON: DE99050965; BR: EW7040000; TRN: AHC29927%%143
- Resource Relation:
- Other Information: PBD: 25 Aug 1998
- Country of Publication:
- United States
- Language:
- English
Similar Records
Separation of organic ion exchange resins from sludge -- engineering study
Particle Size (Sieving) and Enthalpy (Acid Calorimetry) Analysis of Single-Pull K East Basin Floor and Pit Sludges
Related Subjects
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS
FUEL STORAGE POOLS
HANFORD RESERVATION
REMEDIAL ACTION
SLUDGES
RADIOACTIVE WASTE PROCESSING
ION EXCHANGE MATERIALS
SEPARATION PROCESSES
052001
054000
050900
WASTE PROCESSING
HEALTH AND SAFETY
TRANSPORT, HANDLING, AND STORAGE