September 2016 Most Viewed Documents for Materials

  1. The influence of grain size on the mechanical properties ofsteel
    Morris Jr., J.W. (2001)

    1116

  2. Fatigue design curves for 6061-T6 aluminum
    Yahr, G.T. (1993)

    714

  3. Heat Treatment Procedure Qualification -- Final Technical Report
    Robert C. Voigt (2004)

    571

  4. Charpy impact test results on five materials and NIST verification specimens using instrumented 2-mm and 8-mm strikers
    Nanstad, R.K.; Sokolov, M.A. (1995)

    552

  5. Mechanical properties and energy absorption characteristics of a polyurethane foam
    Goods, S.H.; Neuschwanger, C.L.; Henderson, C.; Skala, D.M. (1997)

    345

  6. Results of charpy V-notch impact testing of structural steel specimens irradiated at {approximately}30{degrees}C to 1 x 10{sup 16} neutrons/cm{sup 2} in a commercial reactor cavity
    Iskander, S.K.; Stoller, R.E. (1997)

    290

  7. Comparison of three Ni-Hard I alloys
    Dogan, Omer N.; Hawk, Jeffrey A.; Rice, J. (Texaloy Foundry Co., Inc., Floresville, Texas) (2004)

    216

  8. Ferrite Measurement in Austenitic and Duplex Stainless Steel Castings - Literature Review
    Lundin, C.D.; Zhou, G.; Ruprecht, W. (1999)

    210

  9. Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review
    Doebling, S.W.; Farrar, C.R.; Prime, M.B.; Shevitz, D.W. (1996)

    173

  10. A study of polyether-polyol- and polyester-polyol-based rigid urethane foam systems
    Madden, J.P.; Baker, G.K.; Smith, C.H. (1971)

    169

  11. Sensitization, intergranular attack, stress corrosion cracking, and irradiation effects on the corrosion of iron--chromium--nickel alloys
    Wu, P.C.S. (1978)

    155

  12. P-type doping of GaN
    Wong, R.K. (2000)

    154

  13. Grain refinement of permanent mold cast copper base alloys. Final report
    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M. (2004)

    142

  14. Verification of Allowable Stresses In ASME Section III Subsection NH For Grade 91 Steel & Alloy 800H
    R. W. Swindeman; M. J. Swindeman; B. W. Roberts; B. E. Thurgood; D. L. Marriott (2007)

    141

  15. Ferrite Measurement in Austenitic and Duplex Stainless Steel Castings - Final Report
    Lundin, C.D.; Zhou, G.; Ruprecht, W. (1999)

    140

  16. PROPERTIES AND PERFORMANCE OF CEMENT-BASED GROUTS FOR GEOTHERMAL HEAT PUMP APPLICATIONS.
    ALLAN,M.L. (1999)

    140

  17. Enhancing thermal conductivity of fluids with nanoparticles
    Choi, S.U.S.; Eastman, J.A. (1995)

    116

  18. Metals design handbook
    Betts, W.S. (1988)

    111

  19. The Band Gap of AlGaN Alloys
    Biefeld, R.M.; Crawford, M.H.; Han, J.; Lee, S.R.; Petersen, G.A.; Wright, A.F. (1999)

    108

  20. Fundamental Mechanisms of Roughening and Smoothing During Thin Film Deposition
    Headrick, Randall [Univ. of Vermont, Burlington, VT (United States)] (2016)

    104

Last updated on Wednesday 12 October 2016