skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Strain aging in tungsten heavy alloys

Abstract

This paper reports on tungsten heavy alloys which are two-phase mixtures of body center cubic (BCC) tungsten surrounded by a face center cubic (FCC) matrix. The matrix is most often composed of nickel and iron in a ratio of 70:30 but, occasionally, the matrix may also contain cobalt or copper. Nickel, however, is always the primary matrix component. The tungsten heavy alloy is fabricated through powder metallurgy techniques. Elemental powders are blended, pressed to shape, and sintered. Depending upon the tungsten content, the sintering temperatures are usually in the range of 1450{degrees}C to 1525{degrees}C. These temperatures are high enough that, as a result, the matrix is at the liquid phase and the process is known as liquid phase sintering. At the liquid phase temperature, the matrix becomes saturated with tungsten, but this does not change the FCC character of the matrix. The sintering is usually done in a hydrogen atmosphere furnace in order to reduce the oxides on the tungsten powder surfaces and create clean, active surfaces which will enhance the adherence between the tungsten and the matrix. The hydrogen atmosphere also creates the presence of excess dissolved hydrogen in the alloy. It has been shown that the hydrogen degradesmore » the toughness and ductility of the heavy alloy. A post-sintering vacuum heat treatment is generally required to insure that there is no residual hydrogen present. The as-sintered tensile strength of a 90% tungsten, 7% nickel, 3% iron alloy (90W) is in the range of 800 to 940 MPa and can be increased significantly by cold working, usually rolling or swaging. Swaging to reductions in area of 20% can result in tensile strengths of 1250 MPa or more. As the strength increases, the elongation, which may have been 30% or more, decreases to less than 5%.« less

Authors:
;  [1]
  1. Army Materials Research Agency, Watertown, MA (United States). Materials Technology Lab.
Publication Date:
OSTI Identifier:
5126396
Resource Type:
Journal Article
Journal Name:
Scripta Metallurgica; (United States)
Additional Journal Information:
Journal Volume: 25:1; Journal ID: ISSN 0036-9748
Country of Publication:
United States
Language:
English
Subject:
36 MATERIALS SCIENCE; MATRIX MATERIALS; BONDING; TUNGSTEN; TUNGSTEN ALLOYS; TENSILE PROPERTIES; BCC LATTICES; COBALT; COPPER; DUCTILITY; FCC LATTICES; HEAT TREATMENTS; HYDROGEN EMBRITTLEMENT; IRON; LIQUID PHASE EPITAXY; NICKEL; POWDER METALLURGY; RESIDUAL STRESSES; ALLOYS; CRYSTAL LATTICES; CRYSTAL STRUCTURE; CUBIC LATTICES; ELEMENTS; EMBRITTLEMENT; EPITAXY; FABRICATION; JOINING; MATERIALS; MECHANICAL PROPERTIES; METALLURGY; METALS; STRESSES; TRANSITION ELEMENTS; 360103* - Metals & Alloys- Mechanical Properties; 360101 - Metals & Alloys- Preparation & Fabrication

Citation Formats

Dowding, R J, and Tauer, K J. Strain aging in tungsten heavy alloys. United States: N. p., 1991. Web. doi:10.1016/0956-716X(91)90365-8.
Dowding, R J, & Tauer, K J. Strain aging in tungsten heavy alloys. United States. https://doi.org/10.1016/0956-716X(91)90365-8
Dowding, R J, and Tauer, K J. 1991. "Strain aging in tungsten heavy alloys". United States. https://doi.org/10.1016/0956-716X(91)90365-8.
@article{osti_5126396,
title = {Strain aging in tungsten heavy alloys},
author = {Dowding, R J and Tauer, K J},
abstractNote = {This paper reports on tungsten heavy alloys which are two-phase mixtures of body center cubic (BCC) tungsten surrounded by a face center cubic (FCC) matrix. The matrix is most often composed of nickel and iron in a ratio of 70:30 but, occasionally, the matrix may also contain cobalt or copper. Nickel, however, is always the primary matrix component. The tungsten heavy alloy is fabricated through powder metallurgy techniques. Elemental powders are blended, pressed to shape, and sintered. Depending upon the tungsten content, the sintering temperatures are usually in the range of 1450{degrees}C to 1525{degrees}C. These temperatures are high enough that, as a result, the matrix is at the liquid phase and the process is known as liquid phase sintering. At the liquid phase temperature, the matrix becomes saturated with tungsten, but this does not change the FCC character of the matrix. The sintering is usually done in a hydrogen atmosphere furnace in order to reduce the oxides on the tungsten powder surfaces and create clean, active surfaces which will enhance the adherence between the tungsten and the matrix. The hydrogen atmosphere also creates the presence of excess dissolved hydrogen in the alloy. It has been shown that the hydrogen degrades the toughness and ductility of the heavy alloy. A post-sintering vacuum heat treatment is generally required to insure that there is no residual hydrogen present. The as-sintered tensile strength of a 90% tungsten, 7% nickel, 3% iron alloy (90W) is in the range of 800 to 940 MPa and can be increased significantly by cold working, usually rolling or swaging. Swaging to reductions in area of 20% can result in tensile strengths of 1250 MPa or more. As the strength increases, the elongation, which may have been 30% or more, decreases to less than 5%.},
doi = {10.1016/0956-716X(91)90365-8},
url = {https://www.osti.gov/biblio/5126396}, journal = {Scripta Metallurgica; (United States)},
issn = {0036-9748},
number = ,
volume = 25:1,
place = {United States},
year = {Tue Jan 01 00:00:00 EST 1991},
month = {Tue Jan 01 00:00:00 EST 1991}
}