Technical Note: Influence of the phantom material on the absorbed-dose energy dependence of the EBT3 radiochromic film for photons in the energy range 3 keV–18 MeV

Journal Article · Sat Nov 01 00:00:00 EDT 2014 · Medical Physics

DOI:https://doi.org/10.1118/1.4898598· OSTI ID:22320355

Lüdemann, L.; Flühs, A. ^[1]; Brualla, L. ^[2]

---

1. Medical Physics, Strahlenklinik, Universitätsklinikum Essen, Hufelandstraße 55, Essen D-45122 (Germany)
2. NCTeam, Strahlenklinik, Universitätsklinikum Essen, Hufelandstraße 55, Essen D-45122 (Germany)

Purpose: Water is the reference medium for radiation therapy dosimetry, but for film dosimetry it is more practical to use a solid phantom. As the composition of solid phantoms differs from that of water, the energy dependence of film exposed within solid phantoms may also differ. The energy dependence of a radiochromic film for a given beam quality Q (energy for monoenergetic beams) has two components: the intrinsic energy dependence and the absorbed-dose energy dependence f(Q), the latter of which can be calculated through a Monte Carlo simulation of radiation transport. The authors used Monte Carlo simulations to study the influence of the phantom material on the f(Q) of the EBT3 radiochromic film (Ashland Specialty Ingredients, Wayne, NJ) for photon beams with energies between 3 keV and 18 MeV. Methods: All simulations were carried out with the general-purpose Monte Carlo code PENELOPE 2011. The geometrical model consisted of a cylindrical phantom, with the film positioned at different depths depending on the initial photon energy. The authors simulated monoenergetic parallel photon beams and x-ray beams from a superficial therapy system. To validate their choice of simulation parameters, they also calculated f(Q) for older film models, EBT and EBT2, comparing with published results. In addition to water, they calculated f(Q) of the EBT3 film for solid phantom materials commonly used for film dosimetry: RW1 and RW3 (PTW-Freiburg, Freiburg, Germany), Solid Water (Gammex-RMI, Madison, WI), and PMMA. Finally, they combined their calculated f(Q) with published overall energy response data to obtain the intrinsic energy dependence of the EBT3 film in water. Results: The calculated f(Q) for EBT and EBT2 films was statistically compatible with previously published data. Between 10 keV and 18 MeV, the variation found in f(Q) of the EBT3 film for water was within 2.3%, with a standard statistical uncertainty less than 1%. If the quantity dose-to-water in the phantom is considered, which is the common practice in radiation dosimetry, the maximum difference of energy dependence for the solid phantoms with respect to water is about 6%, at an energy of 50 keV. Conclusions: The EBT3 film shows a reasonably constant absorbed-dose energy dependence when irradiated in water. If the dose-to-water in the phantom is considered, the maximum difference of EBT3 film energy dependence with the solid phantoms studied with respect to water is about 6% (at an energy of 50 keV). The reported overall energy dependence of the EBT3 film in water at energies below 100 keV is mainly due to the intrinsic energy dependence.

• OSTI ID: 22320355
• Journal Information: Medical Physics, Vol. 41, Issue 11; Other Information: (c) 2014 American Association of Physicists in Medicine; Country of input: International Atomic Energy Agency (IAEA); ISSN 0094-2405
• Country of Publication: United States
• Language: English

Related Subjects

07 ISOTOPES AND RADIATION SOURCES
60 APPLIED LIFE SCIENCES
ABSORBED RADIATION DOSES
COMPARATIVE EVALUATIONS
COMPUTERIZED SIMULATION
CYLINDRICAL CONFIGURATION
ENERGY DEPENDENCE
FILM DOSIMETRY
FILMS
IRRADIATION
MATERIALS
MONTE CARLO METHOD
PHANTOMS
PHOTON BEAMS
PHOTONS
PMMA
RADIATION TRANSPORT
SOLIDS
STANDARDS
VARIATIONS
WATER
X RADIATION