Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties
Abstract
A novel quenching and partitioning process (Q&P) including the hot stamping (HS) process was studied, using two stamping temperatures (750 °C and 800 °C) and two quenching temperatures (318 °C and 328 °C). This combination is here called Hot Stamping and Quenching and Partitioning process (HSQ&P). The partitioning step was performed at 400 °C for 100 s in all cycles. Microstructural features were comprehensively studied using electron backscattered diffraction and nanoindentation techniques. HSQ&P samples showed a good combination of ductility and high-strength due to the presence of: retained austenite, inter-critical ferrite with low stored internal strain energy, grain refinement via DIFT-effect (deformation induced ferrite transformation), martensite, and bainite. Significant internal stress relief was caused by carbon partitioning, which was induced by the DIFT-effect and the partitioning stage. This also led to a considerable stored energy, which was characterized by the Kernel average dislocation and geometrically necessary dislocation analysis. In addition, predominant {110}//strain direction crystallographic texture was identified, which promotes slip deformation and enhances the mechanical properties. Moreover, remarkable amounts of fine film-like retained austenite oriented along compact crystallographic directions (i.e., $$\langle$$111$$\rangle$$ and $$\langle$$112$$\rangle$$) were observed. Finally, subsize tensile test verified the optimum mechanical behavior of HSQ&P specimens.
- Authors:
-
[1];
- Univ. of Sao Paulo (Brazil)
- Federal Univ. of ABC (Brazil). Center of Engineering, Modelling and Applied Social Sciences
- Univ. of Sao Paulo (Brazil); Delft Univ. of Technology (Netherlands)
- Univ. Tecnológica de Pereira (Colombia). Mechanical Technology Program
- Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
- Publication Date:
- Research Org.:
- Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)
- Sponsoring Org.:
- USDOE
- OSTI Identifier:
- 1606777
- Grant/Contract Number:
- AC05-00OR22725
- Resource Type:
- Accepted Manuscript
- Journal Name:
- Materials & Design
- Additional Journal Information:
- Journal Volume: 186; Journal Issue: C; Journal ID: ISSN 0264-1275
- Publisher:
- Elsevier
- Country of Publication:
- United States
- Language:
- English
- Subject:
- 36 MATERIALS SCIENCE; Nanoindentation; EBSDTRIP-steel; Crystallographic texture; Subsize tensile test
Citation Formats
Ariza-Echeverri, E. A., Masoumi, M., Nishikawa, A. S., Mesa, D. H., Marquez Rossy, Andres, and Tschiptschin, A. P. Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties. United States: N. p., 2019.
Web. doi:10.1016/j.matdes.2019.108329.
Ariza-Echeverri, E. A., Masoumi, M., Nishikawa, A. S., Mesa, D. H., Marquez Rossy, Andres, & Tschiptschin, A. P. Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties. United States. https://doi.org/10.1016/j.matdes.2019.108329
Ariza-Echeverri, E. A., Masoumi, M., Nishikawa, A. S., Mesa, D. H., Marquez Rossy, Andres, and Tschiptschin, A. P. Wed .
"Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties". United States. https://doi.org/10.1016/j.matdes.2019.108329. https://www.osti.gov/servlets/purl/1606777.
@article{osti_1606777,
title = {Development of a new generation of quench and partitioning steels: Influence of processing parameters on texture, nanoindentation, and mechanical properties},
author = {Ariza-Echeverri, E. A. and Masoumi, M. and Nishikawa, A. S. and Mesa, D. H. and Marquez Rossy, Andres and Tschiptschin, A. P.},
abstractNote = {A novel quenching and partitioning process (Q&P) including the hot stamping (HS) process was studied, using two stamping temperatures (750 °C and 800 °C) and two quenching temperatures (318 °C and 328 °C). This combination is here called Hot Stamping and Quenching and Partitioning process (HSQ&P). The partitioning step was performed at 400 °C for 100 s in all cycles. Microstructural features were comprehensively studied using electron backscattered diffraction and nanoindentation techniques. HSQ&P samples showed a good combination of ductility and high-strength due to the presence of: retained austenite, inter-critical ferrite with low stored internal strain energy, grain refinement via DIFT-effect (deformation induced ferrite transformation), martensite, and bainite. Significant internal stress relief was caused by carbon partitioning, which was induced by the DIFT-effect and the partitioning stage. This also led to a considerable stored energy, which was characterized by the Kernel average dislocation and geometrically necessary dislocation analysis. In addition, predominant {110}//strain direction crystallographic texture was identified, which promotes slip deformation and enhances the mechanical properties. Moreover, remarkable amounts of fine film-like retained austenite oriented along compact crystallographic directions (i.e., $\langle$111$\rangle$ and $\langle$112$\rangle$) were observed. Finally, subsize tensile test verified the optimum mechanical behavior of HSQ&P specimens.},
doi = {10.1016/j.matdes.2019.108329},
journal = {Materials & Design},
number = C,
volume = 186,
place = {United States},
year = {Wed Nov 06 00:00:00 EST 2019},
month = {Wed Nov 06 00:00:00 EST 2019}
}
Free Publicly Available Full Text
Publisher's Version of Record
Other availability
Search WorldCat to find libraries that may hold this journal
Cited by: 19 works
Citation information provided by
Web of Science
Web of Science
Save to My Library
You must Sign In or Create an Account in order to save documents to your library.
Works referenced in this record:
Effects of ferrite phase characteristics on microstructure and mechanical properties of thermomechanically-processed low-silicon content TRIP-assisted steels
journal, February 2015
- Hosseini, Seyed Mohammad Kazem; Zarei-Hanzaki, Abbass; Yue, Steve
- Materials Science and Engineering: A, Vol. 626
Dynamic compression property of a low-carbon quenching and partitioning steel
journal, January 2016
- Huang, Feng; Yang, Jilan; Guo, Zhenghong
- Materials Science and Engineering: A, Vol. 651
Unique impact of ferrite in influencing austenite stability and deformation behavior in a hot-rolled Fe–Mn–Al–C steel
journal, February 2014
- Cai, Z. H.; Ding, H.; Misra, R. D. K.
- Materials Science and Engineering: A, Vol. 595
Carbon partitioning into austenite after martensite transformation
journal, May 2003
- Speer, J.; Matlock, D. K.; De Cooman, B. C.
- Acta Materialia, Vol. 51, Issue 9
Fast-heating for intercritical annealing of cold-rolled quenching and partitioning steel
journal, July 2016
- Liu, Geng; Zhang, Shengen; Li, Jun
- Materials Science and Engineering: A, Vol. 669
A novel phase transition behavior during dynamic partitioning and analysis of retained austenite in quenched and partitioned steels
journal, January 2018
- Li, Y. J.; Kang, J.; Zhang, W. N.
- Materials Science and Engineering: A, Vol. 710
A cyclic austenite reversion treatment for stabilizing austenite in the medium manganese steels
journal, July 2017
- Zhu, Jianing; Ding, Ran; He, Jianguo
- Scripta Materialia, Vol. 136
Designing a Novel DQ&P Process through Physical Simulation Studies
journal, July 2013
- Somani, Mahesh C.; Porter, David A.; Karjalainen, L. Pentti
- Materials Science Forum, Vol. 762
Effect of partitioning procedure on microstructure and mechanical properties of a hot-rolled directly quenched and partitioned steel
journal, January 2014
- Tan, Xiaodong; Xu, Yunbo; Yang, Xiaolong
- Materials Science and Engineering: A, Vol. 594
Effect of intercritical deformation on microstructure and mechanical properties of a low-silicon aluminum-added hot-rolled directly quenched and partitioned steel
journal, February 2016
- Tan, Xiao-Dong; Xu, Yun-Bo; Ponge, Dirk
- Materials Science and Engineering: A, Vol. 656
Evolution of microstructure and its influence on tensile properties in thermo-mechanically controlled processed (TMCP) quench and partition (Q&P) steel
journal, September 2017
- Parthiban, R.; Ghosh Chowdhury, Sandip; Harikumar, K. C.
- Materials Science and Engineering: A, Vol. 705
Enhanced mechanical properties of a hot stamped advanced high-strength steel treated by quenching and partitioning process
journal, April 2011
- Liu, Heping; Lu, Xianwen; Jin, Xuejun
- Scripta Materialia, Vol. 64, Issue 8
Micro and macro-mechanical behavior of a transformation-induced plasticity steel developed by thermomechanical processing followed by quenching and partitioning
journal, January 2016
- Karam-Abian, M.; Zarei-Hanzaki, A.; Abedi, H. R.
- Materials Science and Engineering: A, Vol. 651
An ultrahigh strength steel produced through deformation-induced ferrite transformation and Q&P process
journal, April 2012
- Chen, MingMing; Wu, RiMing; Liu, HePing
- Science China Technological Sciences, Vol. 55, Issue 7
An ultrahigh strength steel with ultrafine-grained microstructure produced through intercritical deformation and partitioning process
journal, October 2015
- Liu, Heping; Sun, Huer; Liu, Bin
- Materials & Design, Vol. 83
Application of Hot Stamping Process by Integrating Quenching & Partitioning Heat Treatment to Improve Mechanical Properties
journal, January 2014
- Han, Xianhong; Zhong, Yaoyao; Yang, Kun
- Procedia Engineering, Vol. 81
Effect of Quenching and Partitioning with Hot Stamping on Martensite Transformation and Mechanical Properties of AHSS
journal, June 2015
- Chang, Ying; Li, Guanzhong; Wang, Cunyu
- Journal of Materials Engineering and Performance, Vol. 24, Issue 8
Research on Q&P hot stamping process integrated with fractional cooling strategy
journal, January 2017
- Han, Xianhong; Li, Yuanyuan; Chen, SiSi
- Procedia Engineering, Vol. 207
Impact of Si on Microstructure and Mechanical Properties of 22MnB5 Hot Stamping Steel Treated by Quenching & Partitioning (Q&P)
journal, November 2017
- Linke, Bernd M.; Gerber, Thomas; Hatscher, Ansgar
- Metallurgical and Materials Transactions A, Vol. 49, Issue 1
Multi-scale simulation for hot stamping quenching & partitioning process of high-strength steel
journal, July 2019
- Wang, Zijian; Wang, Kai; Liu, Yong
- Journal of Materials Processing Technology, Vol. 269
Ductile ultra high strength hot stamped steel obtained by Q&P treatments
journal, September 2017
- Krugla, Monika; Rana, Radhakanta; Das, Sourav
- Materials Science and Technology, Vol. 34, Issue 3
Improvement of tensile mechanical properties in a TRIP-assisted steel by controlling of crystallographic orientation via HSQ&P processes
journal, January 2018
- Ariza, E. A.; Masoumi, M.; Tschiptschin, A. P.
- Materials Science and Engineering: A, Vol. 713
Evaluation of Carbon Partitioning in New Generation of Quench and Partitioning (Q&P) Steels
journal, June 2018
- Ariza, Edwan Anderson; Poplawsky, Jonathan; Guo, Wei
- Metallurgical and Materials Transactions A, Vol. 49, Issue 10
Effect of fresh martensite on the stability of retained austenite in quenching and partitioning steel
journal, October 2014
- De Knijf, Dorien; Petrov, Roumen; Föjer, Cecilia
- Materials Science and Engineering: A, Vol. 615
Effect of partitioning of Mn and Si on the growth kinetics of cementite in tempered Fe–0.6 mass% C martensite
journal, September 2007
- Miyamoto, G.; Oh, J.; Hono, K.
- Acta Materialia, Vol. 55, Issue 15
Quantitative investigation into the influence of temperature on carbide and austenite evolution during partitioning of a quenched and partitioned steel
journal, August 2016
- Pierce, D. T.; Coughlin, D. R.; Williamson, D. L.
- Scripta Materialia, Vol. 121
Interaction of carbon partitioning, carbide precipitation and bainite formation during the Q&P process in a low C steel
journal, February 2016
- HajyAkbary, Farideh; Sietsma, Jilt; Miyamoto, Goro
- Acta Materialia, Vol. 104
Carbon partitioning during quenching and partitioning heat treatment accompanied by carbide precipitation
journal, March 2015
- Toji, Yuki; Miyamoto, Goro; Raabe, Dierk
- Acta Materialia, Vol. 86
Combined hot stamping and Q&P processing with a hot air partitioning device
journal, December 2018
- Zhu, Bin; Zhu, Jia; Wang, Yanan
- Journal of Materials Processing Technology, Vol. 262
Characterization and methodology for calculating the mechanical properties of a TRIP-steel submitted to hot stamping and quenching and partitioning (Q&P)
journal, August 2016
- Ariza, E. A.; Nishikawa, A. S.; Goldenstein, H.
- Materials Science and Engineering: A, Vol. 671
Deformation induced ferrite transformation in low carbon steels
journal, December 2005
- Dong, Han; Sun, Xinjun
- Current Opinion in Solid State and Materials Science, Vol. 9, Issue 6
Simulation of instrumented indentation and material characterization
journal, January 2005
- Tho, K. K.; Swaddiwudhipong, S.; Liu, Z. S.
- Materials Science and Engineering: A, Vol. 390, Issue 1-2
Finite element and dimensional analysis algorithm for the prediction of mechanical properties of bulk materials and thin films
journal, November 2010
- Pulecio, Sara Aida Rodríguez; Farias, María Cristina Moré; Souza, Roberto Martins
- Surface and Coatings Technology, Vol. 205, Issue 5
Characterization of stress-strain relationships of elastoplastic materials: An improved method with conical and pyramidal indenters
journal, November 2012
- Ma, Z. S.; Zhou, Y. C.; Long, S. G.
- Mechanics of Materials, Vol. 54
Computational modeling of the forward and reverse problems in instrumented sharp indentation
journal, November 2001
- Dao, M.; Chollacoop, N.; Van Vliet, K. J.
- Acta Materialia, Vol. 49, Issue 19
Correlation between nanoindentation and tensile propertiesInfluence of the indentation size effect
journal, November 2003
- Rodriguez, R.; Gutierrez, I.
- Materials Science and Engineering A, Vol. 361, Issue 1-2
Determination of strain hardening parameters of tailor hardened boron steel up to high strains using inverse FEM optimization and strain field matching
journal, February 2016
- Eller, T. K.; Greve, L.; Andres, M.
- Journal of Materials Processing Technology, Vol. 228
Image Quality Analysis: A New Method of Characterizing Microstructures
journal, January 2005
- Wu, Jinghui; Wray, Peter J.; Garcia, Calixto I.
- ISIJ International, Vol. 45, Issue 2
Structural characterization of low-carbon multiphase steels merging advanced research methods with light optical microscopy
journal, May 2016
- Radwański, K.
- Archives of Civil and Mechanical Engineering, Vol. 16, Issue 3
Microstructure and texture of a lightly deformed TRIP-assisted steel characterized by means of the EBSD technique
journal, February 2007
- Petrov, Roumen; Kestens, Leo; Wasilkowska, Anna
- Materials Science and Engineering: A, Vol. 447, Issue 1-2
Application of Electron Backscatter Diffraction Techniques to Quenched and Partitioned Steels
journal, January 2011
- Thomas, Grant; Speer, John; Matlock, David
- Microscopy and Microanalysis, Vol. 17, Issue 3
Improved twin detection via tracking of individual Kikuchi band intensity of EBSD patterns
journal, February 2018
- Rampton, Travis M.; Wright, Stuart I.; Miles, Michael P.
- Ultramicroscopy, Vol. 185
Electron imaging with an EBSD detector
journal, January 2015
- Wright, Stuart I.; Nowell, Matthew M.; de Kloe, René
- Ultramicroscopy, Vol. 148
Characteristics of retained austenite in TRIP steels with bainitic ferrite matrix
journal, December 2011
- Zhang, Mingya; Zhu, Fuxian; Duan, Zhengtao
- Journal of Wuhan University of Technology-Mater. Sci. Ed., Vol. 26, Issue 6
Non-isothermal deformation behavior and FE simulation of ultrahigh strength BR1500HS steel in hot stamping process
journal, April 2016
- Wang, Wurong; Zhang, Lei; Guo, Mengxuan
- The International Journal of Advanced Manufacturing Technology, Vol. 87, Issue 9-12
Temporal oscillatory behavior in deformation induced ferrite transformation in an Fe–C binary system
journal, March 2004
- Mingming Tong, ; Ni, Jun; Zhang, Yutuo
- Scripta Materialia, Vol. 50, Issue 6
Formation of Ultra-fine Grain Structure of Plain Low Carbon Steel through Deformation Induced Ferrite Transformation
journal, January 2003
- Yang, Zhongmin; Wang, Ruizhen
- ISIJ International, Vol. 43, Issue 5
Microstructural Evolution of Carbon Steels in Hot Stamping Processes
journal, January 2012
- Hidaka, Kenta; Takemoto, Yoshito; Senuma, Takehide
- ISIJ International, Vol. 52, Issue 4
Singular behaviour at the end of a tensile crack in a hardening material
journal, January 1968
- Hutchinson, J. W.
- Journal of the Mechanics and Physics of Solids, Vol. 16, Issue 1
Effects of microstructures on the fatigue crack growth behavior of laser additive manufactured ultrahigh-strength AerMet100 steel
journal, April 2018
- Ran, Xian-zhe; Liu, Dong; Li, Jia
- Materials Science and Engineering: A, Vol. 721
Importance and role of grain size in free surface cracking prediction of heavy forgings
journal, February 2015
- Wang, Zhenhua; Sun, Shuhua; Wang, Bo
- Materials Science and Engineering: A, Vol. 625
Effect of Nb on the hydrogen-induced cracking of high-strength low-alloy steel
journal, July 2018
- Zhang, Shiqi; Fan, Endian; Wan, Jifang
- Corrosion Science, Vol. 139
Depth-sensing instrumented indentation with dual sharp indenters
journal, August 2003
- Chollacoop, N.; Dao, M.; Suresh, S.
- Acta Materialia, Vol. 51, Issue 13
Texture and grain boundary study in high strength Fe–18Ni–Co steel related to hydrogen embrittlement
journal, February 2016
- Masoumi, Mohammad; Santos, Luis P. M.; Bastos, Ivan N.
- Materials & Design, Vol. 91
Calculation of the taylor factor and lattice rotations for bcc metals deforming by pencil glide
journal, December 1971
- Rosenberg, J. M.; Piehler, H. R.
- Metallurgical Transactions, Vol. 2, Issue 1
Investigation of contribution of {123} slip planes to development of rolling textures in bee metals by use of Taylor models
journal, May 1995
- Raabe, D.
- Materials Science and Technology, Vol. 11, Issue 5
Microstructure based prediction of strain hardening behavior of dual phase steels
journal, October 2012
- Sodjit, Sawitree; Uthaisangsuk, Vitoon
- Materials & Design, Vol. 41
Role of crystallographic orientation and grain boundaries in fatigue crack propagation in used pearlitic rail steel
journal, April 2018
- Masoumi, Mohammad; Ariza, Edwan Anderson; Sinatora, Amilton
- Materials Science and Engineering: A, Vol. 722
Atomic scale effects of alloying, partitioning, solute drag and austempering on the mechanical properties of high-carbon bainitic–austenitic TRIP steels
journal, October 2012
- Seol, Jae-Bok; Raabe, Dierk; Choi, Puck-Pa
- Acta Materialia, Vol. 60, Issue 17
EBSD, XRD and SRS characterization of a casting Al-7wt%Si alloy processed by equal channel angular extrusion: Dislocation density evaluation
journal, July 2019
- Zribi, Zahra; Ktari, Hassan Houcin; Herbst, Frédéric
- Materials Characterization, Vol. 153
Austenite stability and its effect on the toughness of a high strength ultra-low carbon medium manganese steel plate
journal, October 2016
- Zou, Y.; Xu, Y. B.; Hu, Z. P.
- Materials Science and Engineering: A, Vol. 675
Effect of ultragrain refinement on quenching and partitioning steels manufactured by a novel method
journal, December 2015
- Ding, Ran; Tang, Di; Zhao, Aimin
- Materials & Design, Vol. 87
The stability of retained austenite at different locations during straining of I&Q&P steel
journal, July 2016
- Song, Chenghao; Yu, Hao; Li, Lili
- Materials Science and Engineering: A, Vol. 670
Analysis of the relationship between retained austenite locations and the deformation behavior of quenching and partitioning treated steels
journal, January 2016
- Zhao, H. S.; Li, W.; Zhu, X.
- Materials Science and Engineering: A, Vol. 649
Dynamic transformation of deformed austenite at temperatures above the Ae3
journal, September 2016
- Ghosh, Chiradeep; Aranas, Clodualdo; Jonas, John J.
- Progress in Materials Science, Vol. 82
The Deformation and Ageing of Mild Steel: III Discussion of Results
journal, September 1951
- Hall, E. O.
- Proceedings of the Physical Society. Section B, Vol. 64, Issue 9
Geometrically necessary dislocation densities in olivine obtained using high-angular resolution electron backscatter diffraction
journal, September 2016
- Wallis, David; Hansen, Lars N.; Ben Britton, T.
- Ultramicroscopy, Vol. 168
The role of geometrically necessary dislocations in giving material strengthening
journal, January 2003
- Fleck, N. A.; Ashby, M. F.; Hutchinson, J. W.
- Scripta Materialia, Vol. 48, Issue 2
Measurement of geometrically necessary dislocation density with high resolution electron backscatter diffraction: Effects of detector binning and step size
journal, February 2013
- Jiang, J.; Britton, T. B.; Wilkinson, A. J.
- Ultramicroscopy, Vol. 125
On the stored energy evolution after accumulative roll-bonding of invar alloy
journal, November 2017
- Azzeddine, Hiba; Tirsatine, Kamel; Baudin, Thierry
- Materials Chemistry and Physics, Vol. 201
Numerical simulation of dynamic strain-induced austenite–ferrite transformation in a low carbon steel
journal, June 2009
- Zheng, Chengwu; Xiao, Namin; Hao, Luhan
- Acta Materialia, Vol. 57, Issue 10
Estimation of dislocation density in bainitic microstructures using high-resolution dilatometry
journal, November 2009
- Garcia-Mateo, C.; Caballero, F. G.; Capdevila, C.
- Scripta Materialia, Vol. 61, Issue 9
Experimental study of the distribution of alloying elements after the formation of epitaxial ferrite upon cooling in a low-carbon steel
journal, October 2010
- Santofimia, M. J.; Kwakernaak, C.; Sloof, W. G.
- Materials Characterization, Vol. 61, Issue 10
Stabilization mechanisms of retained austenite in transformation-induced plasticity steel
journal, June 2001
- Wang, Jiajun; Van Der Zwaag, Sybrand
- Metallurgical and Materials Transactions A, Vol. 32, Issue 6
Effect of microstructure on retained austenite stability and work hardening of TRIP steels
journal, May 2011
- Chiang, J.; Lawrence, B.; Boyd, J. D.
- Materials Science and Engineering: A, Vol. 528, Issue 13-14
Effects of retained austenite volume fraction, morphology, and carbon content on strength and ductility of nanostructured TRIP-assisted steels
journal, June 2015
- Shen, Y. F.; Qiu, L. N.; Sun, X.
- Materials Science and Engineering: A, Vol. 636
A New Type of Quenching and Partitioning Processing Developed from Martensitic Pre-microstructure
journal, June 2014
- Ding, Ran; Tang, Di; Zhao, Aimin
- Materials and Manufacturing Processes, Vol. 29, Issue 6
Self-stabilization of untransformed austenite by hydrostatic pressure via martensitic transformation
journal, May 2016
- Nakada, Nobuo; Ishibashi, Yuji; Tsuchiyama, Toshihiro
- Acta Materialia, Vol. 110
Application of electron backscatter diffraction (EBSD) to fracture studies of ferritic steels
journal, March 2002
- Davies, P. A.; Novovic, M.; Randle, V.
- Journal of Microscopy, Vol. 205, Issue 3
High angle boundaries formed by grain subdivision mechanisms
journal, September 1997
- Hughes, D. A.; Hansen, N.
- Acta Materialia, Vol. 45, Issue 9
Modeling the viscoplastic behavior and grain size in a hot worked Nb-bearing high-Mn steel
journal, January 2018
- Ebrahimi, G. R.; Momeni, A.; Ezatpour, H. R.
- Materials Science and Engineering: A, Vol. 714
Microstructural Evolution of a Low-Carbon Steel during Application of Quenching and Partitioning Heat Treatments after Partial Austenitization
journal, November 2008
- Santofimia, M. J.; Zhao, L.; Sietsma, J.
- Metallurgical and Materials Transactions A, Vol. 40, Issue 1
Microstructural evolution and consequent strengthening through niobium-microalloying in a low carbon quenched and partitioned steel
journal, August 2015
- Zhang, Jun; Ding, Hua; Misra, R. D. K.
- Materials Science and Engineering: A, Vol. 641
Comparative study on microstructure and mechanical properties of a C-Mn-Si steel treated by quenching and partitioning (Q&P) processes after a full and intercritical austenitization
journal, January 2017
- Yan, Shu; Liu, Xianghua; Liu, Wayne J.
- Materials Science and Engineering: A, Vol. 684
Comparison on mechanical properties and microstructure of a C–Mn–Si steel treated by quenching and partitioning (Q&P) and quenching and tempering (Q&T) processes
journal, January 2015
- Yan, Shu; Liu, Xianghua; Liu, Wayne J.
- Materials Science and Engineering: A, Vol. 620
In-situ EBSD study of deformation behavior of retained austenite in a low-carbon quenching and partitioning steel via uniaxial tensile tests
journal, August 2016
- Li, Wan-song; Gao, Hong-ye; Nakashima, Hideharu
- Materials Characterization, Vol. 118
Improved cold-rollability of duplex lightweight steels utilizing deformation-induced ferritic transformation
journal, January 2019
- Lee, Yongmoon; Kim, Jae Nam; Kim, Geonhyeong
- Materials Science and Engineering: A, Vol. 742
Works referencing / citing this record:
A robust method for mechanical characterization of heterogeneous materials by nanoindentation grid analysis
journal, September 2020
- Sanchez-Camargo, Cesar-Moises; Hor, Anis; Salem, Mehdi
- Materials & Design, Vol. 194