39 Search Results

Tristructural isotropic (TRISO)-coated fuel particles are designed for use in high-temperature gas-cooled nuclear reactors, featuring a structural SiC layer that may be exposed to oxygen-rich environments over 1000 °C. Surrogate TRISO particles were tested in 0.2–20 kPa O₂ atmospheres to observe the differences in oxidation behavior. Oxide growth mechanisms remained consistent from 1200–1600 °C for each P_{O$$_2$$}, with activation energies of 228 ± 7 kJ/mol for 20 kPa O₂ and 188 ± 8 kJ/mol for 0.2 kPa O₂. At 1600 °C, kinetic analysis revealed a change in oxide growth mechanisms between 0.2 and 6 kPa O2. In 0.2 kPa O₂,more » oxidation produced raised oxide nodules on pockets with nanocrystalline SiC. Oxidation mechanisms were determined using Atom probe tomography. Active SiC oxidation occurred in C-rich grain boundaries with low P_{O$$_2$$}, leading to SiO₂ buildup in porous nodules. Here, this phenomenon was not observed at any temperature in 20 kPa O₂ environments.« less

Here, the spout-bed fluidization behavior of nonspherical, 140 μm SiC feedstock was quantified via particle image velocimetry for varying gas distributor geometries. A bench-scale, room-temperature fluidization setup was assembled to model a 50 mm fluidized bed chemical vapor deposition (FB-CVD) system, and fluidized bed motion was captured using a high-speed camera. Modular tips with varying inlet geometries were 3D printed and tested on the bench-scale rig using identical feedstock and gas flow rates in the range of 3.0–9.0 L/min. Fluidization behavior was quantified by extracting parameters of the bed velocity, frequency, dead time, and other measurements, which were ranked formore » each inlet geometry configuration tested. The results from this work demonstrate that changing the path of inlet gas flow can significantly change the hydrodynamics within a spout-fluidized bed under identical feedstock, loading, and flow rate conditions, potentially enabling experimental control of particle fluidization behavior for a given condition. Moreover, composite rankings of fluidization behavior for unique distributor geometries hold potential to guide the design of FB-CVD experiments for various engineering and scientific applications.« less

In this study, coated fuel particle architectures with ZrC coatings are candidate fuels for advanced power reactors and space nuclear propulsion (SNP) concepts. Owing to its relevance to SNP, the composition, microstructure, and mechanical properties of eight ZrC coatings prepared by fluidized bed chemical vapor deposition were evaluated. Evaluation by SEM and EBSD showed that all grains were columnar. Across the various examined samples, minor axis diameters varied between 0.3 and 1.1 μm, and major axis diameters varied between 0.4 and 2.3 μm. Major and minor diameters increased with thickness particularly at higher deposition temperatures in which the major grainmore » axis (from an ellipse fit to the grain shape) increased by 2.5 μm over the entire coating. Coatings with higher reactive gas flows and Zr/C concentrations closer to 1 were observed to contain nanocrystalline graphite deposits. Reactive gas flow doubling led to increases in coating thickness from around 10–15 μm to around 22–27 μm.« less

In this study, zirconium carbide (ZrC) disks were fabricated using binder jet printing to study the effect of powder feedstock, print parameters, and heat treatment on flowability and final materials properties. A median volumetric particle size smaller than 10 μm was shown to cause the powder to stop flowing during printing. Disks were printed using ZrC with suitable flowability and then heat-treated at temperatures between 1800°C and 2200°C for 1 or 5h. The density, part shrinkage, thermal diffusivity, and fracture strength all increased with increasing temperature and time. The heat-treated disks were then heated to 2200°C for 5h and themore » properties converged for disks of the same particle size, indicating the hottest temperature and longest time of exposure dictates the final properties. Lastly, it was shown that larger particles produce lower density materials with worse thermal diffusivity, most likely because of poor connectivity between particles after heat treatment.« less

TRistructural ISOtropic (TRISO) fuel is a leading-edge nuclear fuel form representing a departure from the more traditional nuclear fuel forms utilized in the reactor fleet of today. Rather than a monolithic fuel pellet of uranium dioxide, integral fuel forms containing TRISO fuel are composed of thousands of microencapsulated uranium-bearing fuel kernels and individually coated with multiple layers of pyrolytic carbon and silicon carbide. These multilayered ceramic coatings serve as an environmental barrier to ensure radioactive and chemically reactive fission products are contained within the reactor fuel elements, but also participate in the transfer of heat generated in the nuclear fuelmore » to the coolant – the primary purpose of a nuclear reactor. Since traditional thermal property measurement techniques, such as laser flash analysis, would be unable to resolve the thermal properties of the individual TRISO coating layers, a simplified frequency-domain thermoreflectance technique has been developed to rapidly map the thermal properties of TRISO particles. Using this technique, the thermal properties of TRISO particles have been mapped from room temperature up to 1000 °C to examine the spatial variation and temperature-dependency of the thermal properties within each layer. Additionally, spatial-domain thermoreflectance was used to examine the anisotropy of the thermal properties for each layer at different locations within a single TRISO particle, and across multiple TRISO particles to assess the intra- and inter-particle uniformity of thermal properties, respectively. To elucidate the underlying causes for the measured variations in thermal properties, scanning electron microscopy and Raman spectroscopy were used to examine variations in microstructure and chemical bonding within the different coating layers. Results from this work are then compared with previous examinations of TRISO fuel particles and microstructurally driven mechanisms for the variations in the measured thermal properties of the different carbonaceous layers are discussed.« less

This work presents an analytical approach for holistically characterizing graphitic matrix pebbles for nuclear applications whereby the macrostructure, microstructure, and thermophysical properties of pebbles are determined. A systematic sectioning method was applied to several pebbles to describe the regional properties of the samples. Intact matrix-only spheres and sections of spheres fabricated by Kairos Power were characterized via optical imaging, x-ray computed tomography, x-ray diffraction, and ellipsometry to determine 2D and 3D macrostructure and anisotropy. The thermophysical properties of these materials were determined via measurements of density, specific heat, thermal expansion, and thermal diffusivity. The results of this study indicate thatmore » the pebble fabrication methods and their resultant effect on microstructure have a nontrivial effect on thermophysical properties, confirming the importance of robust characterization of these components. A discussion of the characterization approach and its applicability to nuclear fuel development activities is also included.« less

Studies on high burnup UO₂ subjected to loss-of-coolant accident conditions have shown that restructured regions of the fuel are susceptible to pulverization and eventual dispersal. Due to a lack of pre-test characterization, the distinct microstructural features rendering the fuel prone to fragmentation remain ambiguous. Four samples of commercially irradiated light-water reactor UO₂ have been characterized utilizing electron backscatter diffraction to assess the susceptible microstructure. The microscopy focused on determining the burnup and temperature conditions responsible for the formation of the different microstructural regions where the regions were denoted as the high-burnup structure (HBS), HBS transition, mid-radial, restructured central, and centralmore » region. Previous works have outlined the specific conditions required for the restructuring of the microstructure into the HBS, but the conditions responsible for the restructuring in the central region of the fuel are not well understood. The four analyzed samples confirm a burnup threshold of 61 GWd/tU, and an unknown temperature range is needed to facilitate the formation of the restructured central region. In conclusion, additional fuel performance evaluations are needed to quantify the temperature range promoting restructuring in the central region.« less

Tristructural isotropic (TRISO) nuclear fuel particles contain a layered spherical shell designed to retain fission products; however, failure occurs in rare cases—commonly initiated in the porous pyrocarbon buffer layer. Achieving a comprehensive understanding of the buffer-initiated failure mechanisms requires detailed characterization of the buffer porosity and its heterogeneous distribution across multiple length scales. Here we performed FIB-SEM tomography across the buffer layer thickness (~100 µm) to produce 3D reconstructions of the buffer microstructure with 50 nm spatial resolution. We found an average overall porosity of ~14%, which does not solely account for the low density of the buffer (50% ofmore » the theoretical density). Additionally, the local porosity and its fluctuation increase from the kernel interface towards the inner pyrocarbon (IPyC) layer, which we attribute to the chemical vapor deposition process conditions during the TRISO particle fabrication. Detailed characterization of the porous microstructure—including analysis of the pore size, distribution, shape, and orientation—provides insight into the process-structure-property-performance relations of TRISO nuclear fuel particles and will inform multiscale models designed to predict the failure of TRISO particles under irradiation.« less

The silicon carbide (SiC) coating in a tristructural isotropic (TRISO) particle acts as a barrier to fission product release during reactor operation and accident scenarios. Oxidation and subsequent failure of the SiC layer during a rare air ingress event is a proposed mechanism for fission product release in a high-temperature gas-cooled reactor (HTGR). Although previous oxidation studies have analyzed unirradiated TRISO particle response, this study compared the oxidation behavior of irradiated and unirradiated TRISO particles from the second Advanced Gas Reactor Fuel Development and Qualification Program irradiation experiment (AGR-2). Particles with exposed SiC were subjected to six varying oxidizing testsmore » in the Furnace for Irradiated TRISO Testing (FITT), examined for failure fraction with the Irradiated Microsphere Gamma Analyzer (IMGA) and characterized with focused ion beam and scanning/transmission electron microscopy techniques to analyze the oxide layer. Uncorrelated unirradiated particle failures throughout the series of exposures suggests that external factors inherent to the experiment increased particle failure sensitivity. However, irradiated particle observations indicated an increased failure response at 400 h 1400 °C in both 2% and 21% O₂ atmospheres above failure associated with external factors. Oxide thickness measurements after 400 h at 1400 °C revealed a greater oxidation rate than predicted by parabolic growth, which was attributed to the increased complexity of the oxide structure at longer exposure times. Altering the atmosphere from 21% to 2% O₂ reduced the average oxide thickness by approximately 12%–14% in both irradiated and unirradiated particles at 400 h 1400 °C. Altogether, the minor variations observed between irradiated and unirradiated particles in this study led to the conclusion that unirradiated TRISO particles can be used to approximate irradiated TRISO oxidation kinetics.« less

High-temperature gas-cooled reactors (HTGRs) use tristructural isotropic (TRISO) particles embedded in a graphitic matrix material to form the integral fuel element. Potential off-normal reactor conditions for HTGRs include steam ingress with temperatures above 1,000 °C. Fuel element exposure to steam can cause the graphitic matrix material to evolve, forming an atmosphere composed of oxidants and oxidation products and potentially exposing the TRISO particles to these conditions. Investigating the oxidation response of TRISO particles exposed to a mixed gas atmosphere will provide insight into the stability under off-normal conditions. In this study, surrogate TRISO particles were exposed to high temperatures (Tmore » = 1,200 °C) in flowing steam (3% < pH₂O < 21%) and CO (pCO < 1%) to determine the oxidation behavior of the SiC layer when exposed to various mixed gas atmospheres. Scanning electron microscopy, x-ray diffraction, and focused ion beam milling was used to determine the impact of CO and steam on the oxidation behavior of the SiC layer. Therefore, the data presented demonstrates how the SiC layer showed strong oxidation resistance due to limited SiO₂ growth and maintained its structural integrity under these off-normal conditions.« less