Z-Pinning approach for 3D printing mechanically isotropic materials
Abstract
Conventional 3D printing approaches are restricted to building up material in a layer-by-layer format, which is more appropriately considered “2.5-D” printing. The layered structure inherently results in significant mechanical anisotropy in printed parts, causing the tensile strength in the build direction (z-axis) to be only a fraction of the in-plane strength – a decrease of 50–75% is common. In this study, a novel “z-pinning” approach is described that allows continuous material to be deposited across multiple layers within the volume of the part. Here, the z-pinning process is demonstrated using a Fused Filament Fabrication (FFF) printer for polylactic acid (PLA) and carbon fiber reinforced PLA. For both materials, z-pinning increased the tensile strength and toughness in the z-direction by more than a factor of 3.5. Direct comparisons to tensile strength in the x-axis showed a significant decrease in mechanical anisotropy as the volume of the pin was increased relative to the void in the rectilinear grid structure. In fact, the PLA sample with the largest pin volume demonstrated mechanically isotropic properties within the statistical uncertainty of the tests. Tensile test results were also analyzed relative to the functional area resisting deformation for each sample.
- Authors:
-
- Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
- Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
- Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Purdue Univ., West Lafayette, IN (United States)
- Publication Date:
- Research Org.:
- Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
- Sponsoring Org.:
- USDOE Office of Energy Efficiency and Renewable Energy (EERE)
- OSTI Identifier:
- 1808415
- Grant/Contract Number:
- AC05-00OR22725
- Resource Type:
- Accepted Manuscript
- Journal Name:
- Additive Manufacturing
- Additional Journal Information:
- Journal Volume: 27; Journal ID: ISSN 2214-8604
- Publisher:
- Elsevier
- Country of Publication:
- United States
- Language:
- English
- Subject:
- 36 MATERIALS SCIENCE; 3D printing; extrusion; fused filament fabrication; anisotropy; interlayer strength
Citation Formats
Duty, Chad, Failla, Jordan, Kim, Pum, Smith, Tyler, Lindahl, John, and Kunc, Vlastimil. Z-Pinning approach for 3D printing mechanically isotropic materials. United States: N. p., 2019.
Web. doi:10.1016/j.addma.2019.03.007.
Duty, Chad, Failla, Jordan, Kim, Pum, Smith, Tyler, Lindahl, John, & Kunc, Vlastimil. Z-Pinning approach for 3D printing mechanically isotropic materials. United States. https://doi.org/10.1016/j.addma.2019.03.007
Duty, Chad, Failla, Jordan, Kim, Pum, Smith, Tyler, Lindahl, John, and Kunc, Vlastimil. Thu .
"Z-Pinning approach for 3D printing mechanically isotropic materials". United States. https://doi.org/10.1016/j.addma.2019.03.007. https://www.osti.gov/servlets/purl/1808415.
@article{osti_1808415,
title = {Z-Pinning approach for 3D printing mechanically isotropic materials},
author = {Duty, Chad and Failla, Jordan and Kim, Pum and Smith, Tyler and Lindahl, John and Kunc, Vlastimil},
abstractNote = {Conventional 3D printing approaches are restricted to building up material in a layer-by-layer format, which is more appropriately considered “2.5-D” printing. The layered structure inherently results in significant mechanical anisotropy in printed parts, causing the tensile strength in the build direction (z-axis) to be only a fraction of the in-plane strength – a decrease of 50–75% is common. In this study, a novel “z-pinning” approach is described that allows continuous material to be deposited across multiple layers within the volume of the part. Here, the z-pinning process is demonstrated using a Fused Filament Fabrication (FFF) printer for polylactic acid (PLA) and carbon fiber reinforced PLA. For both materials, z-pinning increased the tensile strength and toughness in the z-direction by more than a factor of 3.5. Direct comparisons to tensile strength in the x-axis showed a significant decrease in mechanical anisotropy as the volume of the pin was increased relative to the void in the rectilinear grid structure. In fact, the PLA sample with the largest pin volume demonstrated mechanically isotropic properties within the statistical uncertainty of the tests. Tensile test results were also analyzed relative to the functional area resisting deformation for each sample.},
doi = {10.1016/j.addma.2019.03.007},
journal = {Additive Manufacturing},
number = ,
volume = 27,
place = {United States},
year = {Thu Mar 07 00:00:00 EST 2019},
month = {Thu Mar 07 00:00:00 EST 2019}
}
Works referenced in this record:
Mechanical characterization of parts fabricated using fused deposition modeling
journal, October 2003
- Bellini, Anna; Güçeri, Selçuk
- Rapid Prototyping Journal, Vol. 9, Issue 4
Anisotropic material properties of fused deposition modeling ABS
journal, October 2002
- Ahn, Sung‐Hoon; Montero, Michael; Odell, Dan
- Rapid Prototyping Journal, Vol. 8, Issue 4
Investigation of 3D Non-Random Porous Structures by Fused Deposition Modelling
journal, February 2002
- Too, M. H.; Leong, K. F.; Chua, C. K.
- The International Journal of Advanced Manufacturing Technology, Vol. 19, Issue 3
Conformal Printing of Electrically Small Antennas on Three-Dimensional Surfaces
journal, January 2011
- Adams, Jacob J.; Duoss, Eric B.; Malkowski, Thomas F.
- Advanced Materials, Vol. 23, Issue 11
Fracture Surface Analysis of 3D-Printed Tensile Specimens of Novel ABS-Based Materials
journal, March 2014
- Torrado Perez, Angel R.; Roberson, David A.; Wicker, Ryan B.
- Journal of Failure Analysis and Prevention, Vol. 14, Issue 3
Welding of 3D-printed carbon nanotube–polymer composites by locally induced microwave heating
journal, June 2017
- Sweeney, Charles B.; Lackey, Blake A.; Pospisil, Martin J.
- Science Advances, Vol. 3, Issue 6
Effect of processing conditions on the bonding quality of FDM polymer filaments
journal, March 2008
- Sun, Q.; Rizvi, G. M.; Bellehumeur, C. T.
- Rapid Prototyping Journal, Vol. 14, Issue 2
On reducing anisotropy in 3D printed polymers via ionizing radiation
journal, November 2014
- Shaffer, Steven; Yang, Kejia; Vargas, Juan
- Polymer, Vol. 55, Issue 23
Review of z-pinned composite laminates
journal, December 2007
- Mouritz, A. P.
- Composites Part A: Applied Science and Manufacturing, Vol. 38, Issue 12
Using multi-axis material extrusion to improve mechanical properties through surface reinforcement
journal, November 2017
- Kubalak, Joseph R.; Wicks, Alfred L.; Williams, Christopher B.
- Virtual and Physical Prototyping, Vol. 13, Issue 1
Effect of Layer Orientation on Mechanical Properties of Rapid Prototyped Samples
journal, January 2000
- Es-Said, O. S.; Foyos, J.; Noorani, R.
- Materials and Manufacturing Processes, Vol. 15, Issue 1
The importance of carbon fiber to polymer additive manufacturing
journal, September 2014
- Love, Lonnie J.; Kunc, Vlastamil; Rios, Orlando
- Journal of Materials Research, Vol. 29, Issue 17
Structure and mechanical behavior of Big Area Additive Manufacturing (BAAM) materials
journal, January 2017
- Duty, Chad E.; Kunc, Vlastimil; Compton, Brett
- Rapid Prototyping Journal, Vol. 23, Issue 1
Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers
journal, September 2017
- Ferreira, Rafael Thiago Luiz; Amatte, Igor Cardoso; Dutra, Thiago Assis
- Composites Part B: Engineering, Vol. 124
A review of melt extrusion additive manufacturing processes: I. Process design and modeling
journal, April 2014
- N. Turner, Brian; Strong, Robert; A. Gold, Scott
- Rapid Prototyping Journal, Vol. 20, Issue 3
Review of applications for advanced three-dimensional fibre textile composites
journal, December 1999
- Mouritz, A. P.; Bannister, M. K.; Falzon, P. J.
- Composites Part A: Applied Science and Manufacturing, Vol. 30, Issue 12
Highly oriented carbon fiber–polymer composites via additive manufacturing
journal, December 2014
- Tekinalp, Halil L.; Kunc, Vlastimil; Velez-Garcia, Gregorio M.
- Composites Science and Technology, Vol. 105
Short fiber reinforced composites for fused deposition modeling
journal, March 2001
- Zhong, Weihong; Li, Fan; Zhang, Zuoguang
- Materials Science and Engineering: A, Vol. 301, Issue 2
Mechanical behavior of acrylonitrile butadiene styrene fused deposition materials modeling
journal, October 2003
- Rodríguez, José F.; Thomas, James P.; Renaud, John E.
- Rapid Prototyping Journal, Vol. 9, Issue 4
Works referencing / citing this record:
Rheological survey of carbon fiber-reinforced high-temperature thermoplastics for big area additive manufacturing tooling applications
journal, September 2019
- Ajinjeru, Christine; Kishore, Vidya; Chen, Xun
- Journal of Thermoplastic Composite Materials
Strength Increasing Additive Manufacturing Fused Filament Fabrication Technology, Based on Spiral Toolpath Material Deposition
journal, September 2019
- Avdeev, Artem; Shvets, Andrey; Gushchin, Ilya
- Machines, Vol. 7, Issue 3