Impact of iron composition on the properties of an additively manufactured solid solution strengthened nickel base alloy

doi:10.1016/j.msea.2018.01.112

This content will become publicly available on February 28, 2020

Title: Impact of iron composition on the properties of an additively manufactured solid solution strengthened nickel base alloy

Full Record
Other Related Research

Authors:: Khayat, Z. R.; Palmer, T. A.

Publication Date:: 2018-03-01

Sponsoring Org.:: USDOE Office of Energy Efficiency and Renewable Energy (EERE)

OSTI Identifier:: 1591675

Grant/Contract Number:: FOA-0001006

Resource Type:: Publisher's Accepted Manuscript

Journal Name:: Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processing

Additional Journal Information:: Journal Name: Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processing Journal Volume: 718 Journal Issue: C; Journal ID: ISSN 0921-5093

Publisher:: Elsevier

Country of Publication:: Netherlands

Language:: English

Citation Formats


                    Khayat, Z. R., and Palmer, T. A. Impact of iron composition on the properties of an additively manufactured solid solution strengthened nickel base alloy.  Netherlands: N. p., 2018. 
        Web.  doi:10.1016/j.msea.2018.01.112.

Copy to clipboard


                    Khayat, Z. R., & Palmer, T. A. Impact of iron composition on the properties of an additively manufactured solid solution strengthened nickel base alloy.  Netherlands.  doi:10.1016/j.msea.2018.01.112.

Copy to clipboard


                    Khayat, Z. R., and Palmer, T. A. Thu .  
        "Impact of iron composition on the properties of an additively manufactured solid solution strengthened nickel base alloy".  Netherlands.  doi:10.1016/j.msea.2018.01.112.

Copy to clipboard


                    
@article{osti_1591675,

  title        = {Impact of iron composition on the properties of an additively manufactured solid solution strengthened nickel base alloy},

  author       = {Khayat, Z. R. and Palmer, T. A.},

  abstractNote = {},

  doi          = {10.1016/j.msea.2018.01.112},

  journal      = {Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processing},

  number       = C,

  volume       = 718,

  place        = {Netherlands},

  year         = {2018},

  month        = {3}

}

Copy to clipboard

Journal Article:

Free Publicly Available Full Text

This content will become publicly available on February 28, 2020

Publisher's Version of Record

DOI: 10.1016/j.msea.2018.01.112

Other availability

Search WorldCat to find libraries that may hold this journal

Citation Metrics:

Cited by: 7 works

Citation information provided by
Web of Science

Save / Share:

Export Metadata

Save to My Library

Similar records in OSTI.GOV collections:

Matrix composition effects on the tensile properties of tungsten-molybdenum heavy alloys

Journal Article Bose, A. ; German, R.N. - Metallurgical Transactions, A (Physical Metallurgy and Materials Science); (USA)

Tungsten-base heavy alloys are liquid-phase sintered from mixed tungsten, nickel, and iron powders. The sintered product is a composite consisting of interlaced tungsten and solidified matrix (W-Ni-Fe) phases. These alloys are most useful in applications requiring high density, strength, and toughness. The design of improved tungsten heavy alloys has been the subject of several research investigations. Much success has taken place through improved processing, but parallel compositional studies have resulted in new microstructure-property combinations. As part of these investigations, the Ni/Fe ratio has been varied, with the general conclusion that optimal strength and ductility occur with a ratio between 2more »« less
DOI: 10.1007/BF02656550
Effect of substitutions of tungsten, vanadium, molybdenum, and titanium for reduced niobium contents in Inconel Alloy 718

Thesis/Dissertation Ziegler, K.R.

Inconel Alloy 718 is a nickel iron-base superalloy strengthened by the precipitation of the metastable Ni/sub 3/Nb-..gamma..'' phase. Large coherency strains between ..gamma..'' and the matrix result in a slow precipitation rate and an intermediate maximum use temperature. The combination of slow precipitation rate and the relative formability and machinability of Alloy 718 make it a popular material for the fabrication of superalloy components. The dependence on foreign sources of Nb has pointed out the desirability of reducing the Nb content of alloy 718 while maintaining the tensile and stress-rupture properties of the original alloys. The purpose of this investigationmore »« less
ADVANCED LOW-COST INTERMETALLIC COATINGS FOR MOLTEN SALT PUMP IMPELLER

Technical Report Henry, Jeffrey ; Zhou, Joe

1.0 INTRODUCTION The use of solar energy to produce steam for the generation of electricity is an established technology, with multiple designs for concentrating solar power (CSP) steam generators available commercially and a number of such units currently operating. As part of the effort to improve the overall efficiency of this technology, designers have developed thermal energy storage (TES) mechanisms that employ molten salt to capture a portion of the solar energy available during the day-time hours and make that energy available for steam generation during periods when the sun’s energy is not available. In current TES systems, nitrate saltsmore »« less
DOI: 10.2172/1566776
Weldability of High Alloys

Technical Report Maroef, I

The purpose of this study was to investigate the effect of silicon and iron on the weldability of HAYNES HR-160{reg_sign} alloy. HR-I60 alloy is a solid solution strengthened Ni-Co-Cr-Si alloy. The alloy is designed to resist corrosion in sulfidizing and other aggressive high temperature environments. Silicon is added ({approx}2.75%) to promote the formation of a protective oxide scale in environments with low oxygen activity. HR-160 alloy has found applications in waste incinerators, calciners, pulp and paper recovery boilers, coal gasification systems, and fluidized bed combustion systems. HR-160 alloy has been successfully used in a wide range of welded applications. However,more »« less
DOI: 10.2172/885658

Full Text Available
Large-Scale Reactive Extrusion Deposition of Sparse Infill Structures with Solid Perimeters

Conference Hershey, Christopher ; Lindahl, John ; Romberg, Stian ; ...

Large-scale additive manufacturing of reactive polymer systems offers significant improvements over thermoplastics through improved mechanical properties, faster deposition rates, and deposition at ambient temperatures. At ambient temperatures, the resin exists as a viscoelastic liquid which require additional additives for improved rigidity and bead stability. These filler-reinforced resins, or yield stress fluids, are soft solid-like materials able to withstand compressive forces from successive layer deposition until curing leads to bead solidification. When bead deposition is unsupported by previous layers, as is the case when bridging a gap, the creep due to gravitational loading can lead to bead instabilities which result inmore »« less
Full Text Available

Similar Records