National Library of Energy BETA

Sample records for review module rm

  1. Project Execution Plan Review Module (RM) | Department of Energy

    Office of Environmental Management (EM)

    Review Module (RM) Project Execution Plan Review Module (RM) The Project Execution Plan (PEP) Review Module (RM) is a tool that assists DOE federal project review teams in...

  2. Project Execution Plan Review Module (RM) | Department of Energy

    Energy.gov [DOE] (indexed site)

    Project Execution Plan (PEP) Review Module (RM) is a tool that assists DOE federal project ... any size and complexity. Project Execution Plan RM (2.32 MB) More Documents & Publications ...

  3. Quality Assurance for Critical Decision Reviews RM

    Energy.gov [DOE]

    The purpose of this Quality Assurance for Capital Project Critical Decision Review Module (QA RM) is to identify, integrate, and clarify the QA performance objectives, criteria, and guidance needed...

  4. Readiness Review RM

    Energy.gov [DOE]

    This module assists DOE Federal line management in their efforts to bring a project or facility into a condition where it is sufficiently prepared to start or resume operations prior to CD-4...

  5. Readiness Review RM

    Office of Environmental Management (EM)

    ... ISMS Integrated Safety Management System IVR ... Management Oversight Review Board LOI Line of Inquiry MIP ... SER Safety Evaluation Report SME Subject Matter Expert ...

  6. Standard Review Plan (SRP) Modules | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Quality Assurance » Standard Review Plan (SRP) Modules Standard Review Plan (SRP) Modules Standard Review Plan - Critical Decision Handbook Overview Project Management Project Execution Plan Review Module (RM) Risk Management RM Integrated Project Team RM Earned Value Management System RM Acquisition Strategy RM Decommissioning Plan RM Site Transition Guidance Standard Review Plan - Code of Record Engineering and Design Conceptual Design RM Preliminary Design RM Final Design RM Construction

  7. Preliminary Design RM

    Office of Energy Efficiency and Renewable Energy (EERE)

    The PD Review Module (RM) is a tool that assists DOE federal project review teams in evaluating the technical sufficiency of the PD prior to CD-2 approval. This PD RM can be applied anytime during...

  8. Decommissioning Plan RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Decommissioning Plan RM Decommissioning Plan RM The Decommissioning Plan Review (DPR) Module is a tool that assists DOE federal project review teams in evaluating the adequacy of ...

  9. Preliminary Safety Design RM

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Preliminary Safety Design (PSD) Review Module (RM) is a tool that assists DOE federal project review teams in evaluating the adequacy of the Preliminary Safety Design work, processes and...

  10. Acquisition Strategy RM

    Energy.gov [DOE]

    The Acquisition Strategy (AS) Review Module (RM) is a tool that assists Department of Energy (DOE) federal project review teams in evaluating the adequacy of the AS prior to approval of CD-1. The...

  11. Conceptual Safety Design RM

    Energy.gov [DOE]

    The Conceptual Safety Design (CSD) Review Module (RM) is a tool that assists DOE federal project review teams in evaluating the adequacy of the Conceptual Safety Design work, processes and...

  12. Final Design RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Final Design RM Final Design RM The Final Design (FD) Review Module (RM) is a tool that assists Department of Energy (DOE) federal project review teams in evaluating the technical sufficiency of the final design prior to CD-3 approval. The FD RM focuses on the engineering design, technology, safety, and quality assurance to determine whether it meets overall design commitments, technical and safety requirements. Final Design RM (2.38 MB) More Documents & Publications Seismic Design

  13. National Environmental Policy Act RM

    Energy.gov [DOE]

    This NEPA Review Module (RM) is a tool to assist the Office of Environmental Management’s (EM) projects review teams, and managers in complying with the provisions of The Department of Energy’s ...

  14. Safety Design Strategy RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Safety Design Strategy RM Safety Design Strategy RM The SDS Review Module (RM) is a tool that assists DOE federal project review teams in evaluating the adequacy of the conceptual safety design strategy documentation package (Conceptual Safety Design Report) prior to CD-1 approval and the adequacy of the preliminary safety design strategy documentation packaged (Preliminary Safety Design Report) prior to CD- 2 approval. Safety Design Strategy RM (602.89 KB) More Documents & Publications

  15. Checkout, Testing, and Commissioning Plan RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Checkout, Testing, and Commissioning Plan RM Checkout, Testing, and Commissioning Plan RM The CP RM Module is a tool that assists DOE federal project review teams in evaluating the sufficiency of the Commissioning Plan and its implementation. The CP RM can be used by the DOE federal project teams both to evaluate the adequacy of the Commissioning Plan documentation/programs and the execution of programs by the contractor. Commissioning Plan RM (2.88 MB) More Documents & Publications

  16. High Performance Sustainable Building Design RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    High Performance Sustainable Building Design RM High Performance Sustainable Building Design RM The High Performance Sustainable Building Design (HPSBD) Review Module (RM) is a tool that assists the DOE federal project review teams in evaluating the technical sufficiency for projects that may incorporate HPSBD Guiding Principles at CD-1 through CD-4 for both new construction and existing buildings. High Performance Sustainable Building Design RM (2.35 MB) More Documents & Publications

  17. Facility Software Quality Assurance (SQA) for Captal Project Critical Decisions RM

    Energy.gov [DOE]

    The purpose of this Software Quality Assurance for Capital Project Critical Decision Review Module (SQA RM) is to identify, integrate, and clarify, in one EM document, the SQA performance...

  18. Decommissioning Plan RM

    Office of Environmental Management (EM)

    Decommissioning Plan Review Module March 2010 CD-0 O 0 C OFFICE OF D C CD-1 F ENVIRO Standard R Decomm Rev Critical Decisi CD-2 M ONMENTAL Review Plan missioning view Module ion ...

  19. Project Execution Plan RM

    Office of Environmental Management (EM)

    Project Execution Plan (PEP) Review Module March 2010 CD-0 O 0 OFFICE OF P C CD-1 F ENVIRO Standard R Project E Rev Critical Decis CD-2 M ONMENTAL Review Plan Execution view Module ...

  20. Construction Readiness RM

    Office of Environmental Management (EM)

    Construction Readiness Review Module March 2010 CD- [This Rev Readiness -0 view Module w s Review (CRR OFFICE O CD-1 was used to dev R). This Review OF ENVIRO Standard R Construc Rev Critical D CD-2 M velop the Revie w Module cont ONMENTA Review Pla ction Rea view Modul Decision (CD C March 2010 ew Plan for Sal tains the lesson Review.] AL MANAG an (SRP) adiness le D) Applicabili D-3 lt Waste Proce ns learned from GEMENT ity CD-4 ssing Facility ( m the SWPF Co Post Ope (SWPF) Const onstruction

  1. Conceptual Design RM

    Energy.gov [DOE]

    This Review Module is a tool that assists Department of Energy (DOE) federal project review teams in evaluating the adequacy of the conceptual design package prior to CD-1 approval. It focuses on...

  2. Acquisition Strategy RM

    Office of Environmental Management (EM)

    Acquisition Strategy Review Module March 2010 CD-0 O 0 OFFICE OF C CD-1 F ENVIRO Standard R Acquisi Rev Critical Decis CD-2 M ONMENTAL Review Plan ition Stra view Module sion (CD) Ap CD March 2010 L MANAGE n (SRP) ategy e pplicability D-3 EMENT CD-4 Post Ope eration Standard Review Plan, 2 nd Edition, March 2010 i FOREWORD The Standard Review Plan (SRP) 1 provides a consistent, predictable corporate review framework to ensure that issues and risks that could challenge the success of Office of

  3. Conceptual Design RM

    Office of Environmental Management (EM)

    Conceptual Design Review Module March 2010 CD-0 O 0 OFFICE OF C CD-1 F ENVIRO Standard R Concep Rev Critical Decis CD-2 M ONMENTAL Review Plan ptual De view Module sion (CD) Ap CD March 2010 L MANAGE n (SRP) sign e pplicability D-3 EMENT CD-4 Post Ope eration Standard Review Plan, 2 nd Edition, March 2010 i FOREWORD The Standard Review Plan (SRP) 1 provides a consistent, predictable corporate review framework to ensure that issues and risks that could challenge the success of Office of

  4. Facility Disposition Safety Strategy RM

    Energy.gov [DOE]

    The Facility Disposition Safety Strategy (FDSS) Review Module is a tool that assists DOE federal project review teams in evaluating the adequacy of the facility documentation, preparations or...

  5. Module 7 - Integrated Baseline Review and Change Control | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Energy 7 - Integrated Baseline Review and Change Control Module 7 - Integrated Baseline Review and Change Control This module focuses on integrated baseline reviews (IBR) and change control. This module outlines the objective and responsibility of an integrated baseline review. Additionally, this module will discuss the change control process required for implementing earned value. Begin Module >> (418.59

  6. RM Eolica | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    RM Eolica Jump to: navigation, search Name: RM Eolica Place: Cabo de Santo Agostinho, Pernambuco, Brazil Sector: Wind energy Product: Pernambuco-based wind tower manufacturer...

  7. National Environmental Policy Act RM

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    National Environmental Policy Act Review Module March 2010 CD- N -0 OFFICE O National E C CD-1 OF ENVIRO Standa Environm Rev Critical Deci CD-2 M ONMENTA ard Review mental P view Modul ision (CD) A C March 2010 AL MANAG Plan olicy Act le Applicability D-3 GEMENT t (NEPA) CD-4 ) Post Ope eration Standard Review Plan, 2 nd Edition, March 2010 i FOREWORD The Standard Review Plan (SRP) 1 provides a consistent, predictable corporate review framework to ensure that issues and risks that could

  8. Safeguards and Security and Cyber Security RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Safeguards and Security and Cyber Security RM Safeguards and Security and Cyber Security RM The SSCS RM is a tool that assists the DOE federal project review teams in evaluating the technical sufficiency of the project SSCS activities at CD-0 through CD-4. Safeguards and Security and Cyber Security RM (2.31 MB) More Documents & Publications Safeguards and Security Program, acronyms and abbereviations - DOE M 470.4-7 Safeguards and Security Glossary - DOE M 470.4-7 Standard Review Plan -

  9. Commercial Grade Dedication RM

    Office of Energy Efficiency and Renewable Energy (EERE)

    The objective of this Standard Review Plan (SRP) on Commercial Grade Dedication (CGD) is to provide guidance for a uniform review of the CGD activities for office of Environmental Management...

  10. Final Design RM

    Office of Environmental Management (EM)

    ... Quality Assurance This review is primarily derived from the requirements of American Society of Mechanical Engineers (ASME) NQA-1- 2000 or later edition and 10 CFR 830 Subpart A ...

  11. Construction Project Safety and Health Plan RM

    Energy.gov [DOE]

    The Construction Project Safety and Health Plan (CPSHP) Review Module is a tool that assists DOE federal project review teams in evaluating the technical sufficiency of the project readiness in...

  12. Quality Assurance for Critical Decision Reviews RM

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    ... Inquiry National Environmental Policy Act NQA-1 PEP PDS PDSA PSVR Nuclear Quality ... DOE O 414.1C, Quality Assurance, and ASME NQA-1 2004, Part I: Requirements for Quality ...

  13. Risk Management RM | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Risk Management RM Risk Management RM This tool is the process of continuous and iterative identification and control of project risks and opportunities. Risks can be technical, financial, or programmatic. The goal for the risk management system is to either avoid the risk's threat by taking preemptive action or to minimize the risks negative impacts on project performance. Project opportunities identified through the project risk management process can be handled in a similar manner with the

  14. Implementation plan for WRAP Module 1 operational readiness review

    SciTech Connect

    Irons, L.G.

    1994-11-04

    The Waste Receiving and Processing Module 1 (WRAP 1) will be used to receive, sample, treat, and ship contact-handled (CH) transuranic (TRU), low-level waste (LLW), and low-level mixed waste (LLMW) to storage and disposal sites both on the Hanford site and off-site. The primary mission of WRAP 1 is to characterize and certify CH waste in 55-gallon and 85-gallon drums; and its secondary function is to certify CH waste standard waste boxes (SWB) and boxes of similar size for disposal. The WRAP 1 will provide the capability for examination (including x-ray, visual, and contents sampling), limited treatment, repackaging, and certification of CH suspect-TRU waste in 55-gallon drums retrieved from storage, as well as newly generated CH LLW and CH TRU waste drums. The WRAP 1 will also provide examination (X-ray and visual only) and certification of CH LLW and CH TRU waste in small boxes. The decision to perform an Operational Readiness Review (ORR) was made in accordance with WHC-CM-5-34, Solid Waste Disposal Operations Administration, Section 1.4, Operational Readiness Activities. The ORR will ensure plant and equipment readiness, management and personnel readiness, and management programs readiness for the initial startup of the facility. This implementation plan is provided for defining the conduct of the WHC ORR.

  15. Microsoft Word - SANDIA REPORT - final RM6.docx

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ... (LCOE) for this RM6 Oscillating Water Column device in dollars per kilowatt-hour (kWh). ... 67 Figure 1-38: High-level LCOE (centskWh) breakdown per deployment scale for RM6. ...

  16. Reference Inflow Characterization for River Resource Reference Model (RM2)

    SciTech Connect

    Neary, Vincent S

    2011-12-01

    Sandia National Laboratory (SNL) is leading an effort to develop reference models for marine and hydrokinetic technologies and wave and current energy resources. This effort will allow the refinement of technology design tools, accurate estimates of a baseline levelized cost of energy (LCoE), and the identification of the main cost drivers that need to be addressed to achieve a competitive LCoE. As part of this effort, Oak Ridge National Laboratory was charged with examining and reporting reference river inflow characteristics for reference model 2 (RM2). Published turbulent flow data from large rivers, a water supply canal and laboratory flumes, are reviewed to determine the range of velocities, turbulence intensities and turbulent stresses acting on hydrokinetic technologies, and also to evaluate the validity of classical models that describe the depth variation of the time-mean velocity and turbulent normal Reynolds stresses. The classical models are found to generally perform well in describing river inflow characteristics. A potential challenge in river inflow characterization, however, is the high variability of depth and flow over the design life of a hydrokinetic device. This variation can have significant effects on the inflow mean velocity and turbulence intensity experienced by stationary and bottom mounted hydrokinetic energy conversion devices, which requires further investigation, but are expected to have minimal effects on surface mounted devices like the vertical axis turbine device designed for RM2. A simple methodology for obtaining an approximate inflow characterization for surface deployed devices is developed using the relation umax=(7/6)V where V is the bulk velocity and umax is assumed to be the near-surface velocity. The application of this expression is recommended for deriving the local inflow velocity acting on the energy extraction planes of the RM2 vertical axis rotors, where V=Q/A can be calculated given a USGS gage flow time

  17. Literature Review of the Effects of UV Exposure on PV Modules

    Office of Energy Efficiency and Renewable Energy (EERE)

    This PowerPoint presentation, originally presented at the NREL 2013 PV Module Reliability Workshop on Feb. 26-27, 2013 in Denver, CO, presents the literature review of the effects of prolonged UV exposure of PV modules, with a particular emphasis on UV exposure testing using artificial light sources, including fluorescent, Xenon, and metal halide lamps.

  18. Modules

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Modules Modules Modules Approach to Managing The Environment Modules is a system which you can use to specify what software you want to use. If you want to use a particular software package loading its module will take care of the details of modifying your environment as necessary. The advantage of the modules approach is that the you are not required to explicitly specify paths for different executable versions and try to keep their related man paths and environment variables coordinated.

  19. Reference Model 5 (RM5): Oscillating Surge Wave Energy Converter

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ... was developed. The design had an annual electrical power of 108 kilowatts (kW), rated ......... 13 Table 6. Electrical Power Matrix for the RM5 OSWEC Design ...

  20. United States Department of the Interior - RM-53 - Reference...

    OpenEI (Open Energy Information) [EERE & EIA]

    OpenEI Reference LibraryAdd to library PermittingRegulatory Guidance - GuideHandbook: United States Department of the Interior - RM-53 - Reference Manual - Special Park...

  1. 2013 Reliability & Markets Peer Review - Day 2 Presentations...

    Office of Environmental Management (EM)

    Bill Schulze, Cornell (1.45 MB) 2013 R&M Peer Review - Real-time Price Forecast with Big Data: A State Space Approach - Lang Tong, Cornell (1.83 MB) 2013 R&M Peer Review - The ...

  2. A review of stereotactic body radiotherapy – is volumetric modulated arc therapy the answer?

    SciTech Connect

    Sapkaroski, Daniel Osborne, Catherine; Knight, Kellie A

    2015-06-15

    Stereotactic body radiotherapy (SBRT) is a high precision radiotherapy technique used for the treatment of small to moderate extra-cranial tumours. Early studies utilising SBRT have shown favourable outcomes. However, major disadvantages of static field SBRT include long treatment times and toxicity complications. Volumetric modulated arc therapy (VMAT) and intensity modulated radiotherapy (IMRT) may potentially mitigate these disadvantages. This review aims to assess the feasibility of emerging VMAT and IMRT-based SBRT treatment techniques and qualify which offers the best outcome for patients, whilst identifying any emerging and advantageous SBRT planning trends. A review and synthesis of data from current literature up to September 2013 was conducted on EMBASE, Medline, PubMed, Science Direct, Proquest central, Google Scholar and the Cochrane Database of Systematic reviews. Only full text papers comparing VMAT and or IMRT and or Static SBRT were included. Ten papers were identified that evaluated the results of VMAT/IMRT SBRT. Five related to medically inoperable stage 1 and 2 non-small-cell lung cancer (NSCLC), three to spinal metastasis, one related to abdominal lymph node malignancies, with the final one looking at pancreatic adenocarcinoma. Overall treatment times with VMAT were reduced by 66–70% for lung, 46–58% for spine, 42% and 21% for lymph node and pancreatic metastasis respectively, planning constraints were met with several studies showing improved organs at risk sparing with IMRT/VMAT to static SBRT. Both IMRT and VMAT were able to meet all planning constraints in the studies reviewed, with VMAT offering the greatest treatment efficiency. Early clinical outcomes with VMAT and IMRT SBRT have demonstrated excellent local control and favourable survival outcomes.

  3. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Scott Yundt

    Energy.gov [DOE]

    Commenter: Scott Yundt 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  4. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Scott Stafford

    Energy.gov [DOE]

    Commenter: Scott Stafford 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  5. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Cheryl Floreen

    Energy.gov [DOE]

    Commenter: Cheryl Floreen 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  6. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Ed Kvartek

    Office of Energy Efficiency and Renewable Energy (EERE)

    Commenter: Ed Kvartek 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  7. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Reginald Gaylord

    Energy.gov [DOE]

    Commenter: Reginald Gaylord 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  8. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Cameron Anderson

    Energy.gov [DOE]

    Commenter: Cameron Anderson 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  9. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Susan Leckband

    Energy.gov [DOE]

    Commenter: Susan Leckband 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  10. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Steven Jahn

    Energy.gov [DOE]

    Commenter: Steven Jahn 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  11. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Mark Fisher

    Energy.gov [DOE]

    Commenter: Mark Fisher 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  12. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Bret Moscon

    Energy.gov [DOE]

    Commenter: Bret Moscon 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  13. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Marc Kolanz

    Energy.gov [DOE]

    Commenter: Marc Kolanz 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  14. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Jim Withers

    Energy.gov [DOE]

    Commenter: Jim Withers 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  15. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- William R. Kleem

    Energy.gov [DOE]

    Commenter: William R. Kleem 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  16. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- J. Chris Cantwell

    Energy.gov [DOE]

    Commenter: J. Chris Cantwell 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  17. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Mario Moreno

    Energy.gov [DOE]

    Commenter: Mario Moreno 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  18. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Pete Stafford

    Energy.gov [DOE]

    Commenter: Pete Stafford 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  19. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Faye Vleger

    Energy.gov [DOE]

    Commenter: Faye Vleger 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  20. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Anoop Agrawal

    Energy.gov [DOE]

    Commenter: Anoop Agrawal 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  1. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Thomas W. Morris

    Energy.gov [DOE]

    Commenter: Thomas W. Morris 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  2. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Jamie Stalker

    Energy.gov [DOE]

    Commenter: Jamie Stalker 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  3. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Curtis Valle

    Energy.gov [DOE]

    Commenter: Curtis Valle 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  4. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Roby Enge

    Energy.gov [DOE]

    Commenter: Roby Enge 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  5. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Richard L. Dickson

    Energy.gov [DOE]

    Commenter: Richard L. Dickson 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  6. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Timothy Bolden

    Energy.gov [DOE]

    Commenter: Timothy Bolden 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  7. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Thomas Peterson

    Energy.gov [DOE]

    Commenter: Thomas Peterson 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  8. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Terry Vaughn

    Energy.gov [DOE]

    Commenter: Terry Vaughn 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  9. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Paul A. Schulte

    Energy.gov [DOE]

    Commenter: Paul A. Schulte 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  10. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Joseph Herndon

    Energy.gov [DOE]

    Commenter: Joseph Herndon 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  11. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Michael Brisson

    Office of Energy Efficiency and Renewable Energy (EERE)

    Commenter: Michael Brisson 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  12. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Kenneth Meyer

    Energy.gov [DOE]

    Commenter: Kenneth Meyer 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  13. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- John Walter

    Energy.gov [DOE]

    Commenter: John Walter 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  14. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Mark Strauch

    Energy.gov [DOE]

    Commenter: Mark Strauch 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  15. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Troy Bodily

    Energy.gov [DOE]

    Commenter: Troy Bodily 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  16. Preparation for Facility Operations RM | Department of Energy

    Energy Saver

    Code of Record Standard Review Plan (SRP) Standard Review Plan - Code of Record Understanding DOE Quality Assurance Requirements and ASME NQA-1 For Application in DOE Nuclear ...

  17. Reference Model 6 (RM6): Oscillating Wave Energy Converter.

    SciTech Connect

    Bull, Diana L; Smith, Chris; Jenne, Dale Scott; Jacob, Paul; Copping, Andrea; Willits, Steve; Fontaine, Arnold; Brefort, Dorian; Gordon, Margaret Ellen; Copeland, Robert; Jepsen, Richard Alan

    2014-10-01

    This report is an addendum to SAND2013-9040: Methodology for Design and Economic Analysis of Marine Energy Conversion (MEC) Technologies. This report describes an Oscillating Water Column Wave Energy Converter reference model design in a complementary manner to Reference Models 1-4 contained in the above report. In this report, a conceptual design for an Oscillating Water Column Wave Energy Converter (WEC) device appropriate for the modeled reference resource site was identified, and a detailed backward bent duct buoy (BBDB) device design was developed using a combination of numerical modeling tools and scaled physical models. Our team used the methodology in SAND2013-9040 for the economic analysis that included costs for designing, manufacturing, deploying, and operating commercial-scale MEC arrays, up to 100 devices. The methodology was applied to identify key cost drivers and to estimate levelized cost of energy (LCOE) for this RM6 Oscillating Water Column device in dollars per kilowatt-hour ($/kWh). Although many costs were difficult to estimate at this time due to the lack of operational experience, the main contribution of this work was to disseminate a detailed set of methodologies and models that allow for an initial cost analysis of this emerging technology. This project is sponsored by the U.S. Department of Energy's (DOE) Wind and Water Power Technologies Program Office (WWPTO), within the Office of Energy Efficiency & Renewable Energy (EERE). Sandia National Laboratories, the lead in this effort, collaborated with partners from National Laboratories, industry, and universities to design and test this reference model.

  18. Vehicle Technologies Office Merit Review 2016: VTO Diagnostic Security Modules for Electric Vehicle to Building Integration

    Energy.gov [DOE]

    Presentation given by Idaho National Laboratory (INL) at the 2016 DOE Vehicle Technologies Office and Hydrogen and Fuel Cells Program Annual Merit Review and Peer Evaluation Meeting about Vehicle...

  19. U.S. Department of Energy Reference Model Program RM2: Experimental...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    As part of this program, MHK turbine models were tested in a large open channel facility ... RM2 is a river turbine designed for a site modeled after a reach in the lower Mississippi ...

  20. Microsoft PowerPoint - FinalModule8.ppt

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Prepared by: Booz Allen Hamilton Module 8: Government Required Reports Welcome to Module ... Prepared by: Booz Allen Hamilton Review of Previous Modules In the previous seven modules, ...

  1. Sampling and analyses report for December 1991 semiannual postburn sampling at the RM1 UCG site, Hanna, Wyoming

    SciTech Connect

    Lindblom, S.R.

    1992-01-01

    The Rocky Mountain 1 (RM1) underground coal gasification (UCG) test was conducted from November 16, 1987, through February 26, 1988 at a site approximately one mile south of Hanna, Wyoming. The test consisted of a dual-module operation to evaluate the controlled retracting injection point (CRIP) technology, the elongated linked well (ELW) technology, and the interaction of closely spaced modules operating simultaneously. The test caused two cavities to form in the Hanna No. 1 coal seam and associated overburden. The Hanna No. 1 coal seam was approximately 30 ft thick and lay at depths between 350 and 365 ft below the surface in the test area. The coal seam was overlain by sandstones, siltstones, and claystones deposited by various fluvial environments. The groundwater monitoring was designed to satisfy the requirements of the Wyoming Department of Environmental Quality (WDEQ) in addition to providing research data toward the development of UCG technology that minimizes environmental impacts. Further background material and the sampling and analytical procedures associated with the sampling task are described in the Rocky Mountain 1 Postburn Groundwater Monitoring Quality Assurance Plan (Mason and Johnson 1988).

  2. Sampling and analyses report for June 1992 semiannual postburn sampling at the RM1 UCG site, Hanna, Wyoming

    SciTech Connect

    Lindblom, S.R.

    1992-08-01

    The Rocky Mountain 1 (RMl) underground coal gasification (UCG) test was conducted from November 16, 1987 through February 26, 1988 (United Engineers and Constructors 1989) at a site approximately one mile south of Hanna, Wyoming. The test consisted of dual module operation to evaluate the controlled retracting injection point (CRIP) technology, the elongated linked well (ELW) technology, and the interaction of closely spaced modules operating simultaneously. The test caused two cavities to be formed in the Hanna No. 1 coal seam and associated overburden. The Hanna No. 1 coal seam is approximately 30 ft thick and lays at depths between 350 ft and 365 ft below the surface in the test area. The coal seam is overlain by sandstones, siltstones and claystones deposited by various fluvial environments. The groundwater monitoring was designed to satisfy the requirements of the Wyoming Department of Environmental Quality (WDEQ) in addition to providing research data toward the development of UCG technology that minimizes environmental impacts. The June 1992 semiannual groundwater.sampling took place from June 10 through June 13, 1992. This event occurred nearly 34 months after the second groundwater restoration at the RM1 site and was the fifteenth sampling event since UCG operations ceased. Samples were collected for analyses of a limited suite set of parameters as listed in Table 1. With a few exceptions, the groundwater is near baseline conditions. Data from the field measurements and analysis of samples are presented. Benzene concentrations in the groundwater were below analytical detection limits.

  3. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Alliance for Water Efficiency (AWE)

    Energy.gov [DOE]

    Commenter: Alliance for Water Efficiency (AWE) 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  4. 10 CFR 850, Request for Information- Docket Number: HS-RM-10-CBDPP- Christopher R. McKean

    Energy.gov [DOE]

    Commenter: Christopher R. McKean 10 CFR 850 - Request for Information Docket Number: HS-RM-10-CBDPP Comment Close Date: 2/22/2011

  5. Microsoft Word - 2013 R&M Review Agenda v.3.1.docx

    Office of Environmental Management (EM)

    Zimmerman, Dan Shawhan, Jubo Yan, Andy Kindle 10:30 am Real-time Price Forecast with Big Data: A State Space Approach Lang Tong, Liyan Jia 11:15 am Break SESSION VI 11:45 am Power ...

  6. Module 6 - Metrics, Performance Measurements and Forecasting...

    Energy.gov [DOE] (indexed site)

    This module reviews metrics such as cost and schedule variance along with cost and schedule performance indices. In addition, this module will outline forecasting tools such as ...

  7. Microsoft PowerPoint - FinalModule7.ppt

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    7: Integrated Baseline Review and Change Control Prepared by: Module 7 - Integrated Baseline Review and Change Control 1 Prepared by: Booz Allen Hamilton Module 7: Integrated ...

  8. Sampling and analyses report for December 1991 semiannual postburn sampling at the RM1 UCG site, Hanna, Wyoming. [Quarterly report, January--March 1992

    SciTech Connect

    Lindblom, S.R.

    1992-01-01

    The Rocky Mountain 1 (RM1) underground coal gasification (UCG) test was conducted from November 16, 1987, through February 26, 1988 at a site approximately one mile south of Hanna, Wyoming. The test consisted of a dual-module operation to evaluate the controlled retracting injection point (CRIP) technology, the elongated linked well (ELW) technology, and the interaction of closely spaced modules operating simultaneously. The test caused two cavities to form in the Hanna No. 1 coal seam and associated overburden. The Hanna No. 1 coal seam was approximately 30 ft thick and lay at depths between 350 and 365 ft below the surface in the test area. The coal seam was overlain by sandstones, siltstones, and claystones deposited by various fluvial environments. The groundwater monitoring was designed to satisfy the requirements of the Wyoming Department of Environmental Quality (WDEQ) in addition to providing research data toward the development of UCG technology that minimizes environmental impacts. Further background material and the sampling and analytical procedures associated with the sampling task are described in the Rocky Mountain 1 Postburn Groundwater Monitoring Quality Assurance Plan (Mason and Johnson 1988).

  9. Module 1 - Introduction to Earned Value | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    and defines the framework necessary for proper Earned Value management implementation. ... Module 7 - Integrated Baseline Review and Change Control Module 8 - Reporting

  10. Year Modules

    Annual Energy Outlook

    Annual photovoltaic module shipments, 2005-2015 (peak kilowatts) Year Modules 2005 204,996 ... Source: U.S. Energy Information Administration, Form EIA-63B, 'Annual Photovoltaic Cell...

  11. Year Modules

    Annual Energy Outlook

    Table 4. Average value of photovoltaic modules, 2005-2015 Source: U.S. Energy Information Administration, Form EIA-63B, 'Annual Photovoltaic CellModule Shipments Report.' Note: ...

  12. Microsoft Word - EE Tech RM Mar 2013 Appx B - pt 1b - front matter...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    water systems Assess use of DX systems Process and checklist to assess possible energy savings Review utility data of existing AFM analysis tools. Analyze...

  13. Module Configuration

    DOEpatents

    Oweis, Salah; D'Ussel, Louis; Chagnon, Guy; Zuhowski, Michael; Sack, Tim; Laucournet, Gaullume; Jackson, Edward J.

    2002-06-04

    A stand alone battery module including: (a) a mechanical configuration; (b) a thermal management configuration; (c) an electrical connection configuration; and (d) an electronics configuration. Such a module is fully interchangeable in a battery pack assembly, mechanically, from the thermal management point of view, and electrically. With the same hardware, the module can accommodate different cell sizes and, therefore, can easily have different capacities. The module structure is designed to accommodate the electronics monitoring, protection, and printed wiring assembly boards (PWAs), as well as to allow airflow through the module. A plurality of modules may easily be connected together to form a battery pack. The parts of the module are designed to facilitate their manufacture and assembly.

  14. Order Module--DOE-STD-1104-2009, REVIEW AND APPROVAL OF NUCLEAR FACILITY SAFETY BASIS AND SAFETY DESIGN BASIS DOCUMENTS

    Energy.gov [DOE]

    The familiar level of this module is divided into two sections that are intended to provide only an overview of the material contained in DOE-STD-1104-2009, which should be consulted for complete...

  15. Final Environmental Impact Statement, Wetland Assessment for the F- and H-Area Groundwater Remediation Project at the Savannahr River Site (March 2004)

    Energy Saver

    Final Design RM Final Design RM The Final Design (FD) Review Module (RM) is a tool that assists Department of Energy (DOE) federal project review teams in evaluating the technical sufficiency of the final design prior to CD-3 approval. The FD RM focuses on the engineering design, technology, safety, and quality assurance to determine whether it meets overall design commitments, technical and safety requirements. Final Design RM (2.38 MB) More Documents & Publications Seismic Design

  16. Thermionic modules

    DOEpatents

    King, Donald B.; Sadwick, Laurence P.; Wernsman, Bernard R.

    2002-06-18

    Modules of assembled microminiature thermionic converters (MTCs) having high energy-conversion efficiencies and variable operating temperatures manufactured using MEMS manufacturing techniques including chemical vapor deposition. The MTCs incorporate cathode to anode spacing of about 1 micron or less and use cathode and anode materials having work functions ranging from about 1 eV to about 3 eV. The MTCs also exhibit maximum efficiencies of just under 30%, and thousands of the devices and modules can be fabricated at modest costs.

  17. Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development of a HT-seismic Tool; 2010 Geothermal Technology Program Peer Review Report

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    4.4.6 Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development of a HT-seismic Tool Presentation Number: 020 Investigator: Henfling, John (Sandia National Laboratories) Objectives: To design, fabricate and field test two high-temperature seismic tools in an EGS application; to work with commercial partners in the development of the tool; and to develop two electronic designs. Average Overall Score: 2.7/4.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Relevance/ Impact Scientific/

  18. Thermoelectric module

    DOEpatents

    Kortier, William E.; Mueller, John J.; Eggers, Philip E.

    1980-07-08

    A thermoelectric module containing lead telluride as the thermoelectric mrial is encapsulated as tightly as possible in a stainless steel canister to provide minimum void volume in the canister. The lead telluride thermoelectric elements are pressure-contacted to a tungsten hot strap and metallurgically bonded at the cold junction to iron shoes with a barrier layer of tin telluride between the iron shoe and the p-type lead telluride element.

  19. Module 6 - Metrics, Performance Measurements and Forecasting | Department

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    of Energy 6 - Metrics, Performance Measurements and Forecasting Module 6 - Metrics, Performance Measurements and Forecasting This module focuses on the metrics and performance measurement tools used in Earned Value. This module reviews metrics such as cost and schedule variance along with cost and schedule performance indices. In addition, this module will outline forecasting tools such as estimate to complete (ETC) and estimate at completion (EAC). Begin Module >> (471

  20. Photovoltaic module and module arrays

    SciTech Connect

    Botkin, Jonathan; Graves, Simon; Lenox, Carl J. S.; Culligan, Matthew; Danning, Matt

    2013-08-27

    A photovoltaic (PV) module including a PV device and a frame, The PV device has a PV laminate defining a perimeter and a major plane. The frame is assembled to and encases the laminate perimeter, and includes leading, trailing, and side frame members, and an arm that forms a support face opposite the laminate. The support face is adapted for placement against a horizontal installation surface, to support and orient the laminate in a non-parallel or tilted arrangement. Upon final assembly, the laminate and the frame combine to define a unitary structure. The frame can orient the laminate at an angle in the range of 3.degree.-7.degree. from horizontal, and can be entirely formed of a polymeric material. Optionally, the arm incorporates integral feature(s) that facilitate interconnection with corresponding features of a second, identically formed PV module.

  1. Photovoltaic module and module arrays

    DOEpatents

    Botkin, Jonathan; Graves, Simon; Lenox, Carl J. S.; Culligan, Matthew; Danning, Matt

    2012-07-17

    A photovoltaic (PV) module including a PV device and a frame. The PV device has a PV laminate defining a perimeter and a major plane. The frame is assembled to and encases the laminate perimeter, and includes leading, trailing, and side frame members, and an arm that forms a support face opposite the laminate. The support face is adapted for placement against a horizontal installation surface, to support and orient the laminate in a non-parallel or tilted arrangement. Upon final assembly, the laminate and the frame combine to define a unitary structure. The frame can orient the laminate at an angle in the range of 3.degree.-7.degree. from horizontal, and can be entirely formed of a polymeric material. Optionally, the arm incorporates integral feature(s) that facilitate interconnection with corresponding features of a second, identically formed PV module.

  2. Construction Readiness RM

    Energy.gov [DOE]

    The authorization to proceed with construction of a new facility is given at the CD-3 phase of the project management cycle, after completion of the final design. Between CD-3 and CD-4 stages of...

  3. Integrated Project Team RM

    Energy.gov [DOE]

    The Integrated Project Team (IPT) is an essential element of the Department’s acquisition process and will be utilized during all phases of a project life cycle. The IPT is a team of professionals...

  4. Preliminary Safety Design RM

    Office of Environmental Management (EM)

    the Acquisition of Capital Assets, DOE-STD-1189-2008, Integration of Safety into the ... Safety Analysis Report for CD-4. DOE-STD-1189-2008 provides the Department's ...

  5. Risk Management RM

    Office of Environmental Management (EM)

    the Acquisition of Capital Assets, DOE-STD-1189-2008, Integration of Safety into the ... More guidance on addressing safety risks in is contained in DOE-STD-1189-2008. II. PURPOSE ...

  6. Integrated Project Team RM

    Office of Environmental Management (EM)

    ...radioactive waste projects that invoke NQA-1 type requirements? (CO-1.1) Are there ... of appropriate standards(DOE O 414.1C, NQA-1, 10 CFR 50 Appendix B, RW-0333P)? (QA-1.4) ...

  7. Prelminary Design RM

    Office of Environmental Management (EM)

    ... Society of Mechanical Engineers (ASME) NQA-1- 2000 or later edition and 10 CFR 830 ... that the design meets requirements? (NQA-1 300) (QA- 2.1) This should include the ...

  8. Commissioning Plan RM

    Office of Environmental Management (EM)

    Department of Energy Project Development and Finance Workshop: Colorado Commercial-Scale Project Development and Finance Workshop: Colorado September 1, 2015 - 12:00pm Addthis Sept. 1-3, 2015 Golden, Colorado National Renewable Energy Laboratory The DOE Office of Indian Energy hosted a Commercial-Scale Renewable Energy Project Development and Finance Workshop on Sept. 1-3, 2015, at the National Renewable Energy Laboratory in Golden, Colorado. Download workshop agenda and presentations.

  9. Conceptual Safety Design RM

    Office of Environmental Management (EM)

    Oil, and Gas Sectors in the United States (September 2015) | Department of Energy Conceptual Framework for Developing Resilience Metrics for the Electricity, Oil, and Gas Sectors in the United States (September 2015) Conceptual Framework for Developing Resilience Metrics for the Electricity, Oil, and Gas Sectors in the United States (September 2015) This report has been written for the Department of Energy's Office of Electricity Delivery and Energy Reliability to support the Office of

  10. Photovoltaic module energy rating methodology development

    SciTech Connect

    Kroposki, B.; Myers, D.; Emery, K.; Mrig, L.; Whitaker, C.; Newmiller, J.

    1996-05-01

    A consensus-based methodology to calculate the energy output of a PV module will be described in this paper. The methodology develops a simple measure of PV module performance that provides for a realistic estimate of how a module will perform in specific applications. The approach makes use of the weather data profiles that describe conditions throughout the United States and emphasizes performance differences between various module types. An industry-representative Technical Review Committee has been assembled to provide feedback and guidance on the strawman and final approach used in developing the methodology.

  11. Supported PV module assembly

    DOEpatents

    Mascolo, Gianluigi; Taggart, David F.; Botkin, Jonathan D.; Edgett, Christopher S.

    2013-10-15

    A supported PV assembly may include a PV module comprising a PV panel and PV module supports including module supports having a support surface supporting the module, a module registration member engaging the PV module to properly position the PV module on the module support, and a mounting element. In some embodiments the PV module registration members engage only the external surfaces of the PV modules at the corners. In some embodiments the assembly includes a wind deflector with ballast secured to a least one of the PV module supports and the wind deflector. An array of the assemblies can be secured to one another at their corners to prevent horizontal separation of the adjacent corners while permitting the PV modules to flex relative to one another so to permit the array of PV modules to follow a contour of the support surface.

  12. Ballasted photovoltaic module and module arrays

    DOEpatents

    Botkin, Jonathan; Graves, Simon; Danning, Matt

    2011-11-29

    A photovoltaic (PV) module assembly including a PV module and a ballast tray. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes an arm. The ballast tray is adapted for containing ballast and is removably associated with the PV module in a ballasting state where the tray is vertically under the PV laminate and vertically over the arm to impede overt displacement of the PV module. The PV module assembly can be installed to a flat commercial rooftop, with the PV module and the ballast tray both resting upon the rooftop. In some embodiments, the ballasting state includes corresponding surfaces of the arm and the tray being spaced from one another under normal (low or no wind) conditions, such that the frame is not continuously subjected to a weight of the tray.

  13. Modules Software Environment

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Environment » Modules Environment Modules Software Environment NERSC uses the module utility to manage nearly all software. There are two huge advantages of the module approach: NERSC can provide many different versions and/or installations of a single software package on a given machine, including a default version as well as several older and newer versions; and Users can easily switch to different versions or installations without having to explicitly specify different paths. With modules,

  14. Smart Integrated Power Module | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Smart Integrated Power Module Smart Integrated Power Module 2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting ape046_tolbert_2012_p.pdf (1.41 MB) More Documents & Publications High Temperature, High Voltage Fully Integrated Gate Driver Circuit High Temperature, High Voltage Fully Integrated Gate Driver Circuit A Segmented Drive Inverter Topology with a Small DC Bus Capacitor

  15. Detailed Course Module Description

    Energy.gov [DOE]

    This document lists the course modules for building science courses offered at Cornell's Collaborator Sustainable Buildingi Practice course.

  16. Integrating Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Provides an overview of the complete National Energy Modeling System (NEMS) model, and includes brief descriptions of the modules with which the Integrating Module interacts. The emphasis and focus, however, is on the structure and function of the Integrating Module of NEMS.

  17. Modulating lignin in plants

    DOEpatents

    Apuya, Nestor; Bobzin, Steven Craig; Okamuro, Jack; Zhang, Ke

    2013-01-29

    Materials and methods for modulating (e.g., increasing or decreasing) lignin content in plants are disclosed. For example, nucleic acids encoding lignin-modulating polypeptides are disclosed as well as methods for using such nucleic acids to generate transgenic plants having a modulated lignin content.

  18. Thermoelectrics Partnership: Automotive Thermoelectric Modules...

    Energy.gov [DOE] (indexed site)

    Novel Nanostructured Interface Solution for Automotive Thermoelectric Modules Application Thermoelectrics Partnership: Automotive Thermoelectric Modules with Scalable Thermo- and ...

  19. Cavity enhanced terahertz modulation

    SciTech Connect

    Born, N.; Scheller, M.; Moloney, J. V.; Koch, M.

    2014-03-10

    We present a versatile concept for all optical terahertz (THz) amplitude modulators based on a Fabry-Prot semiconductor cavity design. Employing the high reflectivity of two parallel meta-surfaces allows for trapping selected THz photons within the cavity and thus only a weak optical modulation of the semiconductor absorbance is required to significantly damp the field within the cavity. The optical switching yields to modulation depths of more than 90% with insertion efficiencies of 80%.

  20. Bracket for photovoltaic modules

    DOEpatents

    Ciasulli, John; Jones, Jason

    2014-06-24

    Brackets for photovoltaic ("PV") modules are described. In one embodiment, a saddle bracket has a mounting surface to support one or more PV modules over a tube, a gusset coupled to the mounting surface, and a mounting feature coupled to the gusset to couple to the tube. The gusset can have a first leg and a second leg extending at an angle relative to the mounting surface. Saddle brackets can be coupled to a torque tube at predetermined locations. PV modules can be coupled to the saddle brackets. The mounting feature can be coupled to the first gusset and configured to stand the one or more PV modules off the tube.

  1. A search for an excited muon decaying to a muon and two jets in pp collisions at $$\\sqrt{s}\\;=\\;8\\;{\\rm{TeV}}$$ with the ATLAS detector

    DOE PAGES [OSTI]

    Aad, G.; Abbott, B.; Abdallah, J.; Abdinov, O.; Abeloos, B.; Aben, R.; Abolins, M.; AbouZeid, O. S.; Abramowicz, H.; Abreu, H.; et al

    2016-07-11

    In this study, a new search signature for excited leptons is explored. Excited muons are sought in the channelmore » $${pp}\\to \\mu {\\mu }^{* }\\to \\mu \\mu \\ {\\rm{jet}}\\;{\\rm{jet}}$$, assuming both the production and decay occur via a contact interaction. The analysis is based on 20.3 fb–1 of pp collision data at a centre-of-mass energy of $$\\sqrt{s}\\;=\\;8\\;{\\rm{TeV}}$$ taken with the ATLAS detector at the large hadron collider. No evidence of excited muons is found, and limits are set at the 95% confidence level on the cross section times branching ratio as a function of the excited-muon mass $${m}_{{\\mu }^{* }}$$. For $${m}_{{\\mu }^{* }}$$ between 1.3 and 3.0 TeV, the upper limit on $$\\sigma B({\\mu }^{* }\\to \\mu q\\bar{q}$$) is between 0.6 and 1 fb. Limits on $$\\sigma B$$ are converted to lower bounds on the compositeness scale Λ. In the limiting case $${\\rm{\\Lambda }}={m}_{{\\mu }^{* }}$$, excited muons with a mass below 2.8 TeV are excluded. With the same model assumptions, these limits at larger $${\\mu }^{* }$$ masses improve upon previous limits from traditional searches based on the gauge-mediated decay $${\\mu }^{* }\\to \\mu \\gamma $$.« less

  2. Silicon photonic heater-modulator

    DOEpatents

    Zortman, William A.; Trotter, Douglas Chandler; Watts, Michael R.

    2015-07-14

    Photonic modulators, methods of forming photonic modulators and methods of modulating an input optical signal are provided. A photonic modulator includes a disk resonator having a central axis extending along a thickness direction of the disk resonator. The disk resonator includes a modulator portion and a heater portion. The modulator portion extends in an arc around the central axis. A PN junction of the modulator portion is substantially normal to the central axis.

  3. License Structure for Multi-Module Facilities

    SciTech Connect

    Thomas Hicks

    2010-08-01

    The Next Generation Nuclear Plant (NGNP) Project is intended to be the prototype for multi-module commercial high temperature gas reactors (HTGRs) for process heat and/or electricity generation. Part of the objectives of the project are to establish the conditions that would govern or enhance the design, licensing, construction and operation of numerous, modular nuclear plants, particularly suited for industrial applications or that could reduce the risk of such projects. A determination is desired regarding whether a multi-module reactor plant can be licensed with a single Nuclear Regulatory Commission (NRC) review, hearing, and safety evaluation report. If it is determined that a multi-modular reactor plant can be licensed under a single review/hearing process, the structure and the duration of the license for each module will also need to be determined. The purpose of this paper is to describe for the NRC the NGNP position on these two issues and obtain either NRC general concurrence or comments on the approach to these issues. While the current NGNP planning provides for only a single reactor module, the project is intended to provide the basis and establish a licensing framework that can be used by future commercial HTGRs and other reactor designs, including a variety of small modular reactor technologies, with configurations reflecting design standardization of multi-module plants. Therefore, it is important to identify a path for addressing these modular reactor plant issues so that the resolution can be factored into the NGNP Project planning. The NGNP position is that a single combined license (COL) application can be submitted for a multi-modular reactor facility, the COL application can undergo a single NRC review/hearing process, and each module should be issued a separate license.

  4. Module Safety Issues (Presentation)

    SciTech Connect

    Wohlgemuth, J.

    2012-02-01

    Description of how to make PV modules so that they are less likely to turn into safety hazards. Making modules inherently safer with minimum additional cost is the preferred approach for PV. Safety starts with module design to ensure redundancy within the electrical circuitry to minimize open circuits and proper mounting instructions to prevent installation related ground faults. Module manufacturers must control the raw materials and processes to ensure that that every module is built like those qualified through the safety tests. This is the reason behind the QA task force effort to develop a 'Guideline for PV Module Manufacturing QA'. Periodic accelerated stress testing of production products is critical to validate the safety of the product. Combining safer PV modules with better systems designs is the ultimate goal. This should be especially true for PV arrays on buildings. Use of lower voltage dc circuits - AC modules, DC-DC converters. Use of arc detectors and interrupters to detect arcs and open the circuits to extinguish the arcs.

  5. Logs Perl Module

    Energy Science and Technology Software Center

    2007-04-04

    A perl module designed to read and parse the voluminous set of event or accounting log files produced by a Portable Batch System (PBS) server. This module can filter on date-time and/or record type. The data can be returned in a variety of formats.

  6. Membrane module assembly

    DOEpatents

    Kaschemekat, Jurgen

    1994-01-01

    A membrane module assembly adapted to provide a flow path for the incoming feed stream that forces it into prolonged heat-exchanging contact with a heating or cooling mechanism. Membrane separation processes employing the module assembly are also disclosed. The assembly is particularly useful for gas separation or pervaporation.

  7. Membrane module assembly

    DOEpatents

    Kaschemekat, J.

    1994-03-15

    A membrane module assembly is described which is adapted to provide a flow path for the incoming feed stream that forces it into prolonged heat-exchanging contact with a heating or cooling mechanism. Membrane separation processes employing the module assembly are also disclosed. The assembly is particularly useful for gas separation or pervaporation. 2 figures.

  8. Photovoltaic module and interlocked stack of photovoltaic modules

    SciTech Connect

    Wares, Brian S.

    2014-09-02

    One embodiment relates to an arrangement of photovoltaic modules configured for transportation. The arrangement includes a plurality of photovoltaic modules, each photovoltaic module including a frame. A plurality of individual male alignment features and a plurality of individual female alignment features are included on each frame. Adjacent photovoltaic modules are interlocked by multiple individual male alignment features on a first module of the adjacent photovoltaic modules fitting into and being surrounded by corresponding individual female alignment features on a second module of the adjacent photovoltaic modules. Other embodiments, features and aspects are also disclosed.

  9. Optical modulator including grapene

    DOEpatents

    Liu, Ming; Yin, Xiaobo; Zhang, Xiang

    2016-06-07

    The present invention provides for a one or more layer graphene optical modulator. In a first exemplary embodiment the optical modulator includes an optical waveguide, a nanoscale oxide spacer adjacent to a working region of the waveguide, and a monolayer graphene sheet adjacent to the spacer. In a second exemplary embodiment, the optical modulator includes at least one pair of active media, where the pair includes an oxide spacer, a first monolayer graphene sheet adjacent to a first side of the spacer, and a second monolayer graphene sheet adjacent to a second side of the spacer, and at least one optical waveguide adjacent to the pair.

  10. Water heater control module

    DOEpatents

    Hammerstrom, Donald J

    2013-11-26

    An advanced electric water heater control system that interfaces with a high temperature cut-off thermostat and an upper regulating thermostat. The system includes a control module that is electrically connected to the high-temperature cut-off thermostat and the upper regulating thermostat. The control module includes a switch to open or close the high-temperature cut-off thermostat and the upper regulating thermostat. The control module further includes circuitry configured to control said switch in response to a signal selected from the group of an autonomous signal, a communicated signal, and combinations thereof.

  11. Sonication standard laboratory module

    DOEpatents

    Beugelsdijk, Tony; Hollen, Robert M.; Erkkila, Tracy H.; Bronisz, Lawrence E.; Roybal, Jeffrey E.; Clark, Michael Leon

    1999-01-01

    A standard laboratory module for automatically producing a solution of cominants from a soil sample. A sonication tip agitates a solution containing the soil sample in a beaker while a stepper motor rotates the sample. An aspirator tube, connected to a vacuum, draws the upper layer of solution from the beaker through a filter and into another beaker. This beaker can thereafter be removed for analysis of the solution. The standard laboratory module encloses an embedded controller providing process control, status feedback information and maintenance procedures for the equipment and operations within the standard laboratory module.

  12. Photovoltaic module with removable wind deflector (Patent) |...

    Office of Scientific and Technical Information (OSTI)

    Photovoltaic module with removable wind deflector Title: Photovoltaic module with removable wind deflector A photovoltaic (PV) module assembly including a PV module, a deflector, ...

  13. NERSC Python Modules (Edison Only)

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    NERSC Python Modules (Edison Only) NERSC Python Modules (Edison Only) Python Interpreter Modules To use the NERSC-built installation on Edison, type: module load python This loads the default version of the following useful core modules: python_base: Python 2.7.x module. numpy: Defines the numerical array and matrix type and basic operations on them. scipy: Uses numpy to do advanced math, signal processing, optimization, statistics and much more. matplotlib: Plotting/visualization library.

  14. MJJ RM Handbook-new

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    CHAPTER IV - SPECIAL CATEGORIES OF RECORDS 1. General .......................................................................................... 32 2. Classified Records ............................................................................. 32 3. Sensitive Unclassified Records .............................................................. 32 4. Epidemiological and Other Health Study Records ......................................... 32 5. Government-Owned Records

  15. Earned Value Management System RM

    Energy.gov [DOE]

    In recent years Department of Energy (DOE) has developed a number of orders, and guidance documents aimed to improve the overall performance of project management and the acquisition of capital...

  16. Earned Value Management System RM

    Office of Environmental Management (EM)

    and Project Management for the Acquisition of Capital Assets, DOE-STD-1189-2008, Integration of Safety into the Design Process, and EM's internal business management practices. ...

  17. Facility Disposition Safety Strategy RM

    Office of Environmental Management (EM)

    ...EM-0383, Decommissioning Handbook, January 2000 DOE G 413.3-8, Environmental Management (EM) Cleanup Projects ... Transition includes transferring programmatic and financial ...

  18. Photovoltaic Module Qualification Plus Testing

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Photovoltaic Module Qualification Plus Testing Sarah Kurtz, John Wohlgemuth, Michael ... CO 80401 303-275-3000 * www.nrel.gov Photovoltaic Module Qualification Plus Testing ...

  19. Module bay with directed flow

    DOEpatents

    Torczynski, John R.

    2001-02-27

    A module bay requires less cleanroom airflow. A shaped gas inlet passage can allow cleanroom air into the module bay with flow velocity preferentially directed toward contaminant rich portions of a processing module in the module bay. Preferential gas flow direction can more efficiently purge contaminants from appropriate portions of the module bay, allowing a reduced cleanroom air flow rate for contaminant removal. A shelf extending from an air inlet slit in one wall of a module bay can direct air flowing therethrough toward contaminant-rich portions of the module bay, such as a junction between a lid and base of a processing module.

  20. GREET Pretreatment Module

    SciTech Connect

    Adom, Felix K.; Dunn, Jennifer B.; Han, Jeongwoo

    2014-09-01

    A wide range of biofuels and biochemicals can be produced from biomass via different pretreatment technologies that yield sugars. This report documents the material and energy flows that occur when fermentable sugars from four lignocellulosic feedstocks (corn stover, miscanthus, switchgrass, and poplar) are produced via dilute acid pretreatment and ammonia fiber expansion. These flows are documented for inclusion in the pretreatment module of the Greenhouses Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model. Process simulations of each pretreatment technology were developed in Aspen Plus. Material and energy consumption data from Aspen Plus were then compiled in the GREET pretreatment module. The module estimates the cradle-to-gate fossil energy consumption (FEC) and greenhouse gas (GHG) emissions associated with producing fermentable sugars. This report documents the data and methodology used to develop this module and the cradle-to-gate FEC and GHG emissions that result from producing fermentable sugars.

  1. NEMS International Energy Module

    Gasoline and Diesel Fuel Update

    EIA NEMS International Energy Module Model Documentation Report vii Mr. G. Daniel Butler U.S. Department of Energy EI-812 1000 Independence Ave., SW Washington, DC 20585 Tel:...

  2. International Energy Module

    Gasoline and Diesel Fuel Update

    EIA NEMS International Energy Module Model Documentation Report vii Mr. G. Daniel Butler U.S. Department of Energy EI-812 1000 Independence Ave., SW Washington, DC 20585 Tel:...

  3. International Energy Module

    Gasoline and Diesel Fuel Update

    self-contained units which are linked by an integrating mechanism. The NEMS International Energy Module (IEM) computes world oil prices, provides a set of crude oil and refined...

  4. Digital optical conversion module

    DOEpatents

    Kotter, Dale K.; Rankin, Richard A.

    1991-02-26

    A digital optical conversion module used to convert an analog signal to a computer compatible digital signal including a voltage-to-frequency converter, frequency offset response circuitry, and an electrical-to-optical converter. Also used in conjunction with the digital optical conversion module is an optical link and an interface at the computer for converting the optical signal back to an electrical signal. Suitable for use in hostile environments having high levels of electromagnetic interference, the conversion module retains high resolution of the analog signal while eliminating the potential for errors due to noise and interference. The module can be used to link analog output scientific equipment such as an electrometer used with a mass spectrometer to a computer.

  5. Digital optical conversion module

    DOEpatents

    Kotter, D.K.; Rankin, R.A.

    1988-07-19

    A digital optical conversion module used to convert an analog signal to a computer compatible digital signal including a voltage-to-frequency converter, frequency offset response circuitry, and an electrical-to-optical converter. Also used in conjunction with the digital optical conversion module is an optical link and an interface at the computer for converting the optical signal back to an electrical signal. Suitable for use in hostile environments having high levels of electromagnetic interference, the conversion module retains high resolution of the analog signal while eliminating the potential for errors due to noise and interference. The module can be used to link analog output scientific equipment such as an electrometer used with a mass spectrometer to a computer. 2 figs.

  6. Photovoltaic module reliability workshop

    SciTech Connect

    Mrig, L.

    1990-01-01

    The paper and presentations compiled in this volume form the Proceedings of the fourth in a series of Workshops sponsored by Solar Energy Research Institute (SERI/DOE) under the general theme of photovoltaic module reliability during the period 1986--1990. The reliability Photo Voltaic (PV) modules/systems is exceedingly important along with the initial cost and efficiency of modules if the PV technology has to make a major impact in the power generation market, and for it to compete with the conventional electricity producing technologies. The reliability of photovoltaic modules has progressed significantly in the last few years as evidenced by warranties available on commercial modules of as long as 12 years. However, there is still need for substantial research and testing required to improve module field reliability to levels of 30 years or more. Several small groups of researchers are involved in this research, development, and monitoring activity around the world. In the US, PV manufacturers, DOE laboratories, electric utilities and others are engaged in the photovoltaic reliability research and testing. This group of researchers and others interested in this field were brought together under SERI/DOE sponsorship to exchange the technical knowledge and field experience as related to current information in this important field. The papers presented here reflect this effort.

  7. Second generation SLAC modulator

    SciTech Connect

    Donaldson, A.R.; Cron, J.C.; Hanselman, R.R.

    1986-06-01

    The Stanford Linear Accelerator Laboratory has undertaken the construction of a single pass electron-positron collider. In order to reach required beam energy 235 new klystrons needed upgraded modulator systems. The collider will use 50 GeV electrons and positrons. The increase in accelerator energy from the present 30 GeV necessitates the replacement of existing 35 MW klystrons with new 67 MW units. The doubling of klystron output power required a redesign of the modulator system. The 67 MW klystron needs a 350 kV beam voltage pulse with a 3.7 ..mu..s pulse width. A new pulse transformer was designed to deliver the increased voltage and pulse width. Pulse cable design was evaluated to obtain increased reliability of that critical element. The modulator, with the exception of its power supply, was rebuilt to produce the required power increase while enhancing reliability and improving maintainability. An investigation of present thyratron switch tube performance under the new operating conditions resulted in agitation and some warranted panic but these conditions were mitigated after several successful experiments and some evolutionary narrowing of the klystron pulse width. The discussion will cover the upgraded modulator system specifications and some details of the new pulse transformer tank, pulse cable, modulator, and modulator switch tube.

  8. Integrated Module Heat Exchanger

    Energy.gov [DOE]

    2012 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  9. Integrated Power Module Cooling

    Office of Energy Efficiency and Renewable Energy (EERE)

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  10. Previous Reviews

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reviews Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials FAQ for Case Study Authors BER Requirements Review 2015 ASCR Requirements Review 2015 Previous Reviews HEP/NP Requirements Review 2013 FES Requirements Review 2014 BES Requirements Review 2014 Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1 800-333-7638 (Inside US) 1 510-486-7600

  11. Printed Module Interconnects

    SciTech Connect

    Stockert, Talysa R.; Fields, Jeremy D.; Pach, Gregory F.; Mauger, Scott A.; van Hest, Maikel F. A. M.

    2015-06-14

    Monolithic interconnects in photovoltaic modules connect adjacent cells in series, and are typically formed sequentially involving multiple deposition and scribing steps. Interconnect widths of 500 um every 10 mm result in 5% dead area, which does not contribute to power generation in an interconnected solar panel. This work expands on previous work that introduced an alternative interconnection method capable of producing interconnect widths less than 100 um. The interconnect is added to the module in a single step after deposition of the photovoltaic stack, eliminating the need for scribe alignment. This alternative method can be used for all types of thin film photovoltaic modules. Voltage addition with copper-indium-gallium-diselenide (CIGS) solar cells using a 2-scribe printed interconnect approach is demonstrated. Additionally, interconnect widths of 250 um are shown.

  12. Power module assembly

    DOEpatents

    Campbell, Jeremy B.; Newson, Steve

    2011-11-15

    A power module assembly of the type suitable for deployment in a vehicular power inverter, wherein the power inverter has a grounded chassis, is provided. The power module assembly comprises a conductive base layer electrically coupled to the chassis, an insulating layer disposed on the conductive base layer, a first conductive node disposed on the insulating layer, a second conductive node disposed on the insulating layer, wherein the first and second conductive nodes are electrically isolated from each other. The power module assembly also comprises a first capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the first conductive node, and further comprises a second capacitor having a first electrode electrically connected to the conductive base layer, and a second electrode electrically connected to the second conductive node.

  13. Flexible programmable logic module

    DOEpatents

    Robertson, Perry J.; Hutchinson, Robert L.; Pierson, Lyndon G.

    2001-01-01

    The circuit module of this invention is a VME board containing a plurality of programmable logic devices (PLDs), a controlled impedance clock tree, and interconnecting buses. The PLDs are arranged to permit systolic processing of a problem by offering wide data buses and a plurality of processing nodes. The board contains a clock reference and clock distribution tree that can drive each of the PLDs with two critically timed clock references. External clock references can be used to drive additional circuit modules all operating from the same synchronous clock reference.

  14. Photovoltaic module and interlocked stack of photovoltaic modules

    DOEpatents

    Wares, Brian S.

    2012-09-04

    One embodiment relates to an arrangement of photovoltaic modules configured for transportation. The arrangement includes a plurality of photovoltaic modules, each photovoltaic module including a frame having at least a top member and a bottom member. A plurality of alignment features are included on the top member of each frame, and a plurality of alignment features are included on the bottom member of each frame. Adjacent photovoltaic modules are interlocked by the alignment features on the top member of a lower module fitting together with the alignment features on the bottom member of an upper module. Other embodiments, features and aspects are also disclosed.

  15. High-Efficiency Solid-State Heat Pump Module

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Solid-State Heat Pump Module 2016 Building Technologies Office Peer Review Dr. S. Ravi Annapragada annaprs@utrc.utc.com United Technologies Research Center creativecommons.org creativecommons.org 2 Project Summary Timeline: Start date: September, 2015 Planned end date: August, 2017 Key Milestones 1. Phase 1: Demonstrate >8 °C material-level calorimetric performance that enables an electrocaloric module COP > 6.0 2. Phase 2: Demonstrate TRL3 solid-state heat pump module Budget: Total

  16. Microsoft Word - 0-PEP-6-14-07.doc | Department of Energy

    Energy Saver

    Word - 0-PEP-6-14-07.doc Microsoft Word - 0-PEP-6-14-07.doc PSF.pdf More Documents & Publications Sample Project Execution Plan Project Execution Plan Review Module (RM) Microsoft...

  17. Drupal Contributed Modules

    Energy Science and Technology Software Center

    2014-10-01

    These Drupal Modules extend the functionality of Drupal by including specific styles for dates and tabs, publishing options for scheduled and immediate publication of content modes, field visibility in content forms, keyword block filters (taxonomy based), adding content nodes to a specified queue for display in views, and status display of workflow settings.

  18. Formed photovoltaic module busbars

    SciTech Connect

    Rose, Douglas; Daroczi, Shan; Phu, Thomas

    2015-11-10

    A cell connection piece for a photovoltaic module is disclosed herein. The cell connection piece includes an interconnect bus, a plurality of bus tabs unitarily formed with the interconnect bus, and a terminal bus coupled with the interconnect bus. The plurality of bus tabs extend from the interconnect bus. The terminal bus includes a non-linear portion.

  19. Method of monolithic module assembly

    DOEpatents

    Gee, James M.; Garrett, Stephen E.; Morgan, William P.; Worobey, Walter

    1999-01-01

    Methods for "monolithic module assembly" which translate many of the advantages of monolithic module construction of thin-film PV modules to wafered c-Si PV modules. Methods employ using back-contact solar cells positioned atop electrically conductive circuit elements affixed to a planar support so that a circuit capable of generating electric power is created. The modules are encapsulated using encapsulant materials such as EVA which are commonly used in photovoltaic module manufacture. The methods of the invention allow multiple cells to be electrically connected in a single encapsulation step rather than by sequential soldering which characterizes the currently used commercial practices.

  20. Thermoelectrics Partnership: Automotive Thermoelectric Modules...

    Energy.gov [DOE] (indexed site)

    Partnership: Automotive Thermoelectric Modules with Scalable Thermo- and Electro-Mechanical Interfaces Novel Nanostructured Interface Solution for Automotive Thermoelectric ...

  1. Detailed Course Module Description | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Detailed Course Module Description Detailed Course Module Description This document lists the course modules for building science courses offered at Cornell's Collaborator...

  2. Photovoltaic module with removable wind deflector (Patent) |...

    Office of Scientific and Technical Information (OSTI)

    Patent: Photovoltaic module with removable wind deflector Citation Details In-Document Search Title: Photovoltaic module with removable wind deflector A photovoltaic (PV) module ...

  3. Module Solar AG | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Module Solar AG Jump to: navigation, search Name: Module Solar AG Place: Baar, Switzerland Product: A Swiss PV module and materials supplier and developer Coordinates: 40.808083,...

  4. Module isolation devices

    SciTech Connect

    Carolan, Michael Francis; Cooke, John Albert; Buzinski, Michael David

    2010-04-27

    A gas flow isolation device includes a gas flow isolation valve movable from an opened condition to a closed condition. The module isolation valve in one embodiment includes a rupture disk in flow communication with a flow of gas when the module isolation valve is in an opened condition. The rupture disk ruptures when a predetermined pressure differential occurs across it causing the isolation valve to close. In one embodiment the valve is mechanically linked to the rupture disk to maintain the valve in an opened condition when the rupture disk is intact, and which permits the valve to move into a closed condition when the rupture disk ruptures. In another embodiment a crushable member maintains the valve in an open condition, and the flow of gas passed the valve upon rupturing of the rupture disk compresses the crushable member to close the isolation valve.

  5. VERDE Analytic Modules

    Energy Science and Technology Software Center

    2008-01-15

    The Verde Analytic Modules permit the user to ingest openly available data feeds about phenomenology (storm tracks, wind, precipitation, earthquake, wildfires, and similar natural and manmade power grid disruptions and forecast power outages, restoration times, customers outaged, and key facilities that will lose power. Damage areas are predicted using historic damage criteria of the affected area. The modules use a cellular automata approach to estimating the distribution circuits assigned to geo-located substations. Population estimates servedmore » within the service areas are located within 1 km grid cells and converted to customer counts by conversion through demographic estimation of households and commercial firms within the population cells. Restoration times are estimated by agent-based simulation of restoration crews working according to utility published prioritization calibrated by historic performance.« less

  6. Stable local oscillator module.

    SciTech Connect

    Brocato, Robert Wesley

    2007-11-01

    This report gives a description of the development of a Stable Local Oscillator (StaLO) multi-chip module (MCM). It is a follow-on report to SAND2006-6414, Stable Local Oscillator Microcircuit. The StaLO accepts a 100MHz input signal and produces output signals at 1.2, 3.3, and 3.6 GHz. The circuit is built as a multi-chip module (MCM), since it makes use of integrated circuit technologies in silicon and lithium niobate as well as discrete passive components. This report describes the development of an MCM-based version of the complete StaLO, fabricated on an alumina thick film hybrid substrate.

  7. 2015 PV Module Reliability Workshop

    Energy.gov [DOE]

    The National Renewable Energy Laboratory hosts an annual Photovoltaic (PV) Module Reliability Workshop so that solar technology experts can share information leading to the improvement of PV module reliability. Improvements to module reliability reduce the cost of solar electricity and promotes investor confidence in the technology—both critical goals for moving PV technologies deeper into the electricity marketplace.

  8. Tandem resonator reflectance modulator

    DOEpatents

    Fritz, Ian J. (Albuquerque, NM); Wendt, Joel R. (Albuquerque, NM)

    1994-01-01

    A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors.

  9. Tandem resonator reflectance modulator

    DOEpatents

    Fritz, I.J.; Wendt, J.R.

    1994-09-06

    A wide band optical modulator is grown on a substrate as tandem Fabry-Perot resonators including three mirrors spaced by two cavities. The absorption of one cavity is changed relative to the absorption of the other cavity by an applied electric field, to cause a change in total reflected light, as light reflecting from the outer mirrors is in phase and light reflecting from the inner mirror is out of phase with light from the outer mirrors. 8 figs.

  10. Hours Available FY

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    LANSCE-RM 201 RF Replacement Module 2 Sectors AJ HVAC LANSCE-RM 201 RF Replacement Module 3 LANSCE-RM 201 RF Replacement Module 4 Routine Maintenance BGS 12232015 LA-UR-15-29688...

  11. Hours Available FY

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    LANSCE-RM 201 RF Replacement Module 2 Sectors AJ HVAC LANSCE-RM 201 RF Replacement Module 3 LANSCE-RM 201 RF Replacement Module 4 Routine Maintenance BGS 782015 LA-UR-15-25395...

  12. TASMANIAN Sparse Grids Module

    SciTech Connect

    and Drayton Munster, Miroslav Stoyanov

    2013-09-20

    Sparse Grids are the family of methods of choice for multidimensional integration and interpolation in low to moderate number of dimensions. The method is to select extend a one dimensional set of abscissas, weights and basis functions by taking a subset of all possible tensor products. The module provides the ability to create global and local approximations based on polynomials and wavelets. The software has three components, a library, a wrapper for the library that provides a command line interface via text files ad a MATLAB interface via the command line tool.

  13. TASMANIAN Sparse Grids Module

    Energy Science and Technology Software Center

    2013-09-20

    Sparse Grids are the family of methods of choice for multidimensional integration and interpolation in low to moderate number of dimensions. The method is to select extend a one dimensional set of abscissas, weights and basis functions by taking a subset of all possible tensor products. The module provides the ability to create global and local approximations based on polynomials and wavelets. The software has three components, a library, a wrapper for the library thatmore » provides a command line interface via text files ad a MATLAB interface via the command line tool.« less

  14. Introduction of Break-Out Session at the International PV Module Quality Assurance Forum (Presentation)

    SciTech Connect

    Kurtz, S.; Wohlgemuth, J.; Yamamichi, M.; Sample, T.

    2011-07-01

    This presentation outlines review requirements for quality assurance (QA) rating systems, logical design of QA systems, and specific tasks for break-out session 1 of the 2011 International PV Module Quality Assurance Forum.

  15. Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development of a HT-seismic Tool; 2010 Geothermal Technology Program Peer Review Report Fielding of HT-seismic Tools ...

  16. Processing module operating methods, processing modules, and communications systems

    DOEpatents

    McCown, Steven Harvey; Derr, Kurt W.; Moore, Troy

    2014-09-09

    A processing module operating method includes using a processing module physically connected to a wireless communications device, requesting that the wireless communications device retrieve encrypted code from a web site and receiving the encrypted code from the wireless communications device. The wireless communications device is unable to decrypt the encrypted code. The method further includes using the processing module, decrypting the encrypted code, executing the decrypted code, and preventing the wireless communications device from accessing the decrypted code. Another processing module operating method includes using a processing module physically connected to a host device, executing an application within the processing module, allowing the application to exchange user interaction data communicated using a user interface of the host device with the host device, and allowing the application to use the host device as a communications device for exchanging information with a remote device distinct from the host device.

  17. Phase modulation in RF tag

    DOEpatents

    Carrender, Curtis Lee; Gilbert, Ronald W.

    2007-02-20

    A radio frequency (RF) communication system employs phase-modulated backscatter signals for RF communication from an RF tag to an interrogator. The interrogator transmits a continuous wave interrogation signal to the RF tag, which based on an information code stored in a memory, phase-modulates the interrogation signal to produce a backscatter response signal that is transmitted back to the interrogator. A phase modulator structure in the RF tag may include a switch coupled between an antenna and a quarter-wavelength stub; and a driver coupled between the memory and a control terminal of the switch. The driver is structured to produce a modulating signal corresponding to the information code, the modulating signal alternately opening and closing the switch to respectively decrease and increase the transmission path taken by the interrogation signal and thereby modulate the phase of the response signal. Alternatively, the phase modulator may include a diode coupled between the antenna and driver. The modulating signal from the driver modulates the capacitance of the diode, which modulates the phase of the response signal reflected by the diode and antenna.

  18. High Efficiency Solid-State Heat Pump Module | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    High Efficiency Solid-State Heat Pump Module High Efficiency Solid-State Heat Pump Module Electrocaloric Calorimeter. Image courtesy of United Technologies Research Center and BTO Peer Review. Electrocaloric Calorimeter. Image courtesy of United Technologies Research Center and BTO Peer Review. Lead Performer: United Technologies Research Center - East Hartford, CT DOE Total Funding: $1,090,000 Cost Share: $365,000 Project Term: August 2015 - September 2017 Funding Opportunity: Building Energy

  19. Photovoltaic module and module arrays (Patent) | SciTech Connect

    Office of Scientific and Technical Information (OSTI)

    with corresponding features of a second, identically formed PV module. ... Country of Publication: United States Language: English Word Cloud More Like This Full Text ...

  20. Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    of a HT-seismic Tool; 2010 Geothermal Technology Program Peer Review Report | Department of Energy Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development of a HT-seismic Tool; 2010 Geothermal Technology Program Peer Review Report Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development of a HT-seismic Tool; 2010 Geothermal Technology Program Peer Review Report DOE 2010 Geothermal Technologies Program Peer Review hightemp_020_henfling.pdf (195.19 KB)

  1. Modulated preheating and isocurvature perturbations

    SciTech Connect

    Enqvist, Kari; Rusak, Stanislav E-mail: stanislav.rusak@helsinki.fi

    2013-03-01

    We consider a model of preheating where the coupling of the inflaton to the preheat field is modulated by an additional scalar field which is light during inflation. We establish that such a model produces the observed curvature perturbation analogously to the modulated reheating scenario. The contribution of modulated preheating to the power spectrum and to non-Gaussianity can however be significantly larger compared to modulated perturbative reheating. We also consider the implications of the current constraints on isocurvature perturbations in case where the modulating field is responsible for cold dark matter. We find that existing bounds on CDM isocurvature perturbations imply that modulated preheating is unlikely to give a dominant contribution to the curvature perturbation and that the same bounds suggest important constraints on non-Gaussianity and the amount of primordial gravitational waves.

  2. International Energy Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Summarizes the overall structure of the International Energy Model and its interface with other NEMS modules, mathematical specifications of behavioral relationships, and data sources and estimation methods.

  3. module 4 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    4 HR5 TRANSITION BRIEFING PDF icon module 4 More Documents & Publications Microsoft Word - Rev5functionalaccountabilityimplementationplan..doc High Risk Plan Department of...

  4. Photovoltaic concentrator module improvements study

    SciTech Connect

    Levy, S.L.; Kerschen, K.A. ); Hutchison, G. ); Nowlan, M.J. )

    1991-08-01

    This report presents results of a project to design and fabricate an improved photovoltaic concentrator module. Using previous work as a baseline, this study conducted analyses and testing to select major module components and design features. The lens parquet and concentrator solar cell were selected from the highest performing, available components. A single 185X point-focus module was fabricated by the project team and tested at Sandia. Major module characteristics include a 6 by 4 compression-molded acrylic lens parquet (0.737 m{sup 2} area), twenty-four 0.2 ohms-cm, FZ, p-Si solar cells (1.56 cm{sup 2} area) soldered to ceramic substrates and copper heat spreaders, and an aluminized steel housing with corrugated bottom. This project marked the first attempt to use prismatic covers on solar cells in a high-concentration, point-focus application. Cells with 15 percent metallization were obtained, but problems with the fabrication and placement of prismatic covers on these cells lead to the decision not to use covers in the prototype module. Cell assembly fabrication, module fabrication, and module optical design activities are presented here. Test results are also presented for bare cells, cell assemblies, and module. At operating conditions of 981 watts/m{sup 2} DNI and an estimated cell temperature of 65{degrees}C, the module demonstrated an efficiency of 13.9 percent prior to stressed environmental exposure. 12 refs., 56 figs., 7 tabs.

  5. Fortran 90 Source Module

    Energy Science and Technology Software Center

    1998-01-13

    A major advance contained in the new Fortran 90 language standard is the ability to define new data types and the operators associated with them. Writing computer code to implement computations with real and complex three domensional vectors and dyadics is greatly simplified if the equations can be implemented directly, without the need to code the vector arithmetic explicitly. The Fortran 90 module VECTORS contains source code which defines new data types for real andmore » complex 3-dimensional vectors and dyadics, along with the common operations needed to work with these objects. Routines to allow convenient initalization and output of the new types are also included. in keeping with the philosophy of data abstraction, the details of the implementation of the data types are maintained private, and the functions and operators are made generic to simplify the combining of real, complex, single and double precision vectors and dyadics.« less

  6. Light modulating device

    DOEpatents

    Rauh, R. David; Goldner, Ronald B.

    1989-01-01

    In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity.

  7. Photovoltaic module mounting system

    DOEpatents

    Miros, Robert H. J.; Mittan, Margaret Birmingham; Seery, Martin N; Holland, Rodney H

    2012-09-18

    A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

  8. Photovoltaic module mounting system

    DOEpatents

    Miros, Robert H. J.; Mittan, Margaret Birmingham; Seery, Martin N.; Holland, Rodney H.

    2012-04-17

    A solar array mounting system having unique installation, load distribution, and grounding features, and which is adaptable for mounting solar panels having no external frame. The solar array mounting system includes flexible, pedestal-style feet and structural links connected in a grid formation on the mounting surface. The photovoltaic modules are secured in place via the use of attachment clamps that grip the edge of the typically glass substrate. The panel mounting clamps are then held in place by tilt brackets and/or mid-link brackets that provide fixation for the clamps and align the solar panels at a tilt to the horizontal mounting surface. The tilt brackets are held in place atop the flexible feet and connected link members thus creating a complete mounting structure.

  9. Solar heat collector module

    SciTech Connect

    Lightfoot, D.J.

    1980-09-23

    A solar heat system is comprised of a panel or bank of heat collector modules each of which has a fluid-carrying tube of an elongated triangular shape in transverse cross section formed with longitudinally extended inwardly projected heat radiating fins. A tube is mounted within a concavo-convex reflector of a hyperbolic form such that the side walls of the tube are subjected to reflected rays of solar radiation over an effective range of solar exposure of about one hundred and fifty (150*) degrees. The reflected rays are concentrated in a longitudinally extended focal zone on each side wall of the tube and these zones of concentrated solar radiation move transversely of a side wall in response to the angle of the solar rays falling upon the reflector.

  10. Light modulating device

    DOEpatents

    Rauh, R.D.; Goldner, R.B.

    1989-12-26

    In a device for transmitting light, means for controlling the transmissivity of the device, including a ceramic, reversibly electrochromic, crystalline element having a highly reflective state when injected with electrons and charge compensating ions and a highly transmissive state when the electrons and ions are removed, the crystalline element being characterized as having a reflectivity of at least 50% in the reflective state and not greater than 10% in the transmissive state, and means for modulating the crystalline element between the reflective and transmissive states by injecting ions into the crystalline element in response to an applied electrical current of a first polarity and removing the ions in response to an applied electrical current of a second polarity are disclosed. 1 fig.

  11. Low-voltage differentially-signaled modulators

    SciTech Connect

    Zortman, William A.; Lentine, Anthony L.; Hsia, Alexander H.; Watts, Michael R.

    2015-09-08

    Photonic modulators and methods of modulating an input optical signal are provided. A photonic modulator includes at least one modulator section and differential drive circuitry. The at least one modulator section includes a P-type layer and an N-type layer forming a PN junction in the modulator section. The differential drive circuitry is electrically coupled to the P-type layer and the N-type layer of the at least one modulator section.

  12. 2010 Geothermal Technology Program Peer Review Report | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Energy 0 Geothermal Technology Program Peer Review Report 2010 Geothermal Technology Program Peer Review Report DOE Geothermal Technology Program Peer Review 2010_gtp_peer_review_report_final.pdf (2.53 MB) More Documents & Publications Detecting Fractures Using Technology at High Temperatures and Depths - Geothermal Ultrasonic Fracture Imager (GUFI); 2010 Geothermal Technology Program Peer Review Report Fielding of HT-seismic Tools and Evaluation of HT-FPGA Module - Development of a

  13. Integrated Modules for Bioassay (IMBA)

    Energy.gov [DOE]

    IMBA ExpertTM (IX) software suite comprises a series of independent modules (referred to as sub-modules) that implement the International Commission on Radiological Protection (ICRP) Publication 66, Human Respiratory Tract Model (HRTM) and the ICRP Publications 30 (series), 67, 68, 69, and 71 biokinetic models.

  14. Macroeconomic Activity Module - NEMS Documentation

    Reports and Publications

    2016-01-01

    Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Macroeconomic Activity Module (MAM) used to develop the Annual Energy Outlook for 2016 (AEO2016). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code

  15. Macroeconomic Activity Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Macroeconomic Activity Module (MAM) used to develop the Annual Energy Outlook for 2014 (AEO2014). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code

  16. Argonne's SpEC Module

    SciTech Connect

    Harper, Jason

    2014-05-05

    Jason Harper, an electrical engineer in Argonne National Laboratory's EV-Smart Grid Interoperability Center, discusses his SpEC Module invention that will enable fast charging of electric vehicles in under 15 minutes. The module has been licensed to BTCPower.

  17. Argonne's SpEC Module

    ScienceCinema

    Harper, Jason

    2014-06-05

    Jason Harper, an electrical engineer in Argonne National Laboratory's EV-Smart Grid Interoperability Center, discusses his SpEC Module invention that will enable fast charging of electric vehicles in under 15 minutes. The module has been licensed to BTCPower.

  18. National Ignition Facility Shot Data Analysis Module Guidelines

    SciTech Connect

    Azevedo, S; Glenn, S; Lopez, A; Warrick, A; Beeler, R

    2007-10-03

    This document provides the guidelines for software development of modules to be included in Shot Data Analysis (SDA) for the National Ignition Facility (NIF). An Analysis Module is a software entity that groups a set of (typically cohesive) functions, procedures and data structures for performing an analysis task relevant to NIF shot operations. Each module must have its own unique identification (module name), clear interface specifications (data inputs and outputs), and internal documentation. It is vitally important to the NIF Program that all shot-related data be processed and analyzed in a consistent way that is reviewed by scientific and engineering experts. SDA is part of a NIF Integrated Product Team (IPT) whose goal is to provide timely and accurate reporting of shot results to NIF campaign experimentalists. Other elements of the IPT include the Campaign Management Tool (CMT) for configuring experiments, a data archive and provisioning system called CMS, a calibration and configuration database (CDMS), and a shot data visualization tool (SDV). We restrict our scope at this time to guidelines for modules written in Interactive Data Language, or IDL1. This document has sections describing example IDL modules and where to find them, how to set up a development environment, IDL programming guidelines, shared IDL procedures for general use, and revision control.

  19. Force Modulator System

    SciTech Connect

    Redmond Clark

    2009-04-30

    Many metal parts manufacturers use large metal presses to shape sheet metal into finished products like car body parts, jet wing and fuselage surfaces, etc. These metal presses take sheet metal and - with enormous force - reshape the metal into a fully formed part in a manner of seconds. Although highly efficient, the forces involved in forming metal parts also damage the press itself, limit the metals used in part production, slow press operations and, when not properly controlled, cause the manufacture of large volumes of defective metal parts. To date, the metal-forming industry has not been able to develop a metal-holding technology that allows full control of press forces during the part forming process. This is of particular importance in the automotive lightweighting efforts under way in the US automotive manufacturing marketplace. Metalforming Controls Technology Inc. (MC2) has developed a patented press control system called the Force Modulator that has the ability to control these press forces, allowing a breakthrough in stamping process control. The technology includes a series of hydraulic cylinders that provide controlled tonnage at all points in the forming process. At the same time, the unique cylinder design allows for the generation of very high levels of clamping forces (very high tonnages) in very small spaces; a requirement for forming medium and large panels out of HSS and AHSS. Successful production application of these systems testing at multiple stamping operations - including Ford and Chrysler - has validated the capabilities and economic benefits of the system. Although this technology has been adopted in a number of stamping operations, one of the primary barriers to faster adoption and application of this technology in HSS projects is system cost. The cost issue has surfaced because the systems currently in use are built for each individual die as a custom application, thus driving higher tooling costs. This project proposed to better

  20. OCGen Module Mooring Project

    SciTech Connect

    McEntee, Jarlath

    2015-02-06

    Ocean Renewable Power Company's OCGen Module Mooring Project provided an extensive research, design, development, testing and data collection effort and analysis conducted with respect to a positively buoyant, submerged MHK device secured to the seabed using a tensioned mooring system. Different analytic tools were evaluated for their utility in the design of submerged systems and their moorings. Deployment and testing of a prototype OCGen® system provided significant data related to mooring line loads and system attitude and station keeping. Mooring line loads were measured in situ and reported against flow speeds. The Project made a significant step in the development of designs, methodologies and practices related to floating and mooring of marine hydrokinetic (MHK) devices. Importantly for Ocean Renewable Power Company, the Project provided a sound basis for advancing a technically and commercially viable OCGen® Power System. The OCGen® Power System is unique in the MHK industry and, in itself, offers distinct advantages of MHK devices that are secured to the seabed using fixed structural frames. Foremost among these advantages are capital and operating cost reductions and increased power extraction by allowing the device to be placed at the most energetic level of the water column.

  1. Common Geometry Module

    Energy Science and Technology Software Center

    2005-01-01

    The Common Geometry Module (CGM) is a code library which provides geometry functionality used for mesh generation and other applications. This functionality includes that commonly found in solid modeling engines, like geometry creation, query and modification; CGM also includes capabilities not commonly found in solid modeling engines, like geometry decomposition tools and support for shared material interfaces. CGM is built upon the ACIS solid modeling engine, but also includes geometry capability developed beside and onmore » top of ACIS. CGM can be used as-is to provide geometry functionality for codes needing this capability. However, CGM can also be extended using derived classes in C++, allowing the geometric model to serve as the basis for other applications, for example mesh generation. CGM is supported on Sun Solaris, SGI, HP, IBM, DEC, Linux and Windows NT platforms. CGM also indudes support for loading ACIS models on parallel computers, using MPI-based communication. Future plans for CGM are to port it to different solid modeling engines, including Pro/Engineer or SolidWorks. CGM is being released into the public domain under an LGPL license; the ACIS-based engine is available to ACIS licensees on request.« less

  2. Working with Modules within Perl and Python

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Working with Modules within Perl and Python Working with Modules within Perl and Python It can often be convenient to work with the modules system from within perl or python...

  3. Photovoltaic module with adhesion promoter

    DOEpatents

    Xavier, Grace

    2013-10-08

    Photovoltaic modules with adhesion promoters and methods for fabricating photovoltaic modules with adhesion promoters are described. A photovoltaic module includes a solar cell including a first surface and a second surface, the second surface including a plurality of interspaced back-side contacts. A first glass layer is coupled to the first surface by a first encapsulating layer. A second glass layer is coupled to the second surface by a second encapsulating layer. At least a portion of the second encapsulating layer is bonded directly to the plurality of interspaced back-side contacts by an adhesion promoter.

  4. Photovoltaic Energy Technology Module | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Photovoltaic Energy Technology Module AgencyCompany Organization: World Bank Sector: Energy Focus...

  5. Module Encapsulation Materials, Processing and Testing (Presentation)

    SciTech Connect

    Pern, J.

    2008-12-01

    Study of PV module encapsulation materials, processing, and testing shows that overall module reliability is determined by all component materials and processing factors.

  6. Module Encapsulation Materials, Processing and Testing (Presentation...

    Office of Scientific and Technical Information (OSTI)

    Module Encapsulation Materials, Processing and Testing (Presentation) Pern, J. 14 SOLAR ENERGY; 36 MATERIALS SCIENCE; ENCAPSULATION; PROCESSING; RELIABILITY; TESTING PV; MODULE...

  7. Lateral electrodeposition of compositionally modulated metal layers

    DOEpatents

    Hearne, Sean J

    2014-03-25

    A method for making a laterally modulated metallic structure that is compositionally modulated in the lateral direction with respect to a substrate.

  8. Biomass Energy Technology Module | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Biomass Energy Technology Module AgencyCompany Organization: World Bank Sector: Energy Focus Area:...

  9. Wind Energy Technology Module | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Wind Energy Technology Module AgencyCompany Organization: World Bank Sector: Energy Focus Area:...

  10. Village Hydro Technology Module | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Hydro Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Village Hydro Technology Module AgencyCompany Organization: World Bank Sector: Energy Focus...

  11. Ubbink Solar Modules BV | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Solar Modules BV Place: Cologne, North Rhine-Westphalia, Germany Zip: 50933 Product: German manufacturer of PV modules, main customer was Ecostream that has agreed to purchase...

  12. Residential Demand Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Model Documentation - Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Residential Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, and FORTRAN source code.

  13. Industrial Demand Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

  14. Photovoltaic Module Qualification Plus Testing

    SciTech Connect

    Kurtz, S.; Wohlgemuth, J.; Kempe, M.; Bosco, N.; Hacke, P.; Jordan, D.; Miller, D. C.; Silverman, T. J.; Phillips, N.; Earnest, T.; Romero, R.

    2013-12-01

    This report summarizes a set of test methods that are in the midst of being incorporated into IEC 61215 for certification of a module design or other tests that go beyond certification to establish bankability.

  15. Renewable Fuels Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    This report documents the objectives, analytical approach, and design of the National Energy Modeling System (NEMS) Renewable Fuels Module (RFM) as it relates to the production of the Annual Energy Outlook forecasts.

  16. Compact magnetic energy storage module

    DOEpatents

    Prueitt, Melvin L.

    1994-01-01

    A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module.

  17. Compact magnetic energy storage module

    DOEpatents

    Prueitt, M.L.

    1994-12-20

    A superconducting compact magnetic energy storage module in which a plurality of superconducting toroids, each having a toroidally wound superconducting winding inside a poloidally wound superconducting winding, are stacked so that the flow of electricity in each toroidally wound superconducting winding is in a direction opposite from the direction of electrical flow in other contiguous superconducting toroids. This allows for minimal magnetic pollution outside of the module. 4 figures.

  18. Solar cell module lamination process

    DOEpatents

    Carey, Paul G.; Thompson, Jesse B.; Aceves, Randy C.

    2002-01-01

    A solar cell module lamination process using fluoropolymers to provide protection from adverse environmental conditions and thus enable more extended use of solar cells, particularly in space applications. A laminate of fluoropolymer material provides a hermetically sealed solar cell module structure that is flexible and very durable. The laminate is virtually chemically inert, highly transmissive in the visible spectrum, dimensionally stable at temperatures up to about 200.degree. C. highly abrasion resistant, and exhibits very little ultra-violet degradation.

  19. Photovoltaic Degradation Rates -- An Analytical Review

    SciTech Connect

    Jordan, D. C.; Kurtz, S. R.

    2012-06-01

    As photovoltaic penetration of the power grid increases, accurate predictions of return on investment require accurate prediction of decreased power output over time. Degradation rates must be known in order to predict power delivery. This article reviews degradation rates of flat-plate terrestrial modules and systems reported in published literature from field testing throughout the last 40 years. Nearly 2000 degradation rates, measured on individual modules or entire systems, have been assembled from the literature, showing a median value of 0.5%/year. The review consists of three parts: a brief historical outline, an analytical summary of degradation rates, and a detailed bibliography partitioned by technology.

  20. Wide-range voltage modulation

    SciTech Connect

    Rust, K.R.; Wilson, J.M.

    1992-06-01

    The Superconducting Super Collider`s Medium Energy Booster Abort (MEBA) kicker modulator will supply a current pulse to the abort magnets which deflect the proton beam from the MEB ring into a designated beam stop. The abort kicker will be used extensively during testing of the Low Energy Booster (LEB) and the MEB rings. When the Collider is in full operation, the MEBA kicker modulator will abort the MEB beam in the event of a malfunction during the filling process. The modulator must generate a 14-{mu}s wide pulse with a rise time of less than 1 {mu}s, including the delay and jitter times. It must also be able to deliver a current pulse to the magnet proportional to the beam energy at any time during ramp-up of the accelerator. Tracking the beam energy, which increases from 12 GeV at injection to 200 GeV at extraction, requires the modulator to operate over a wide range of voltages (4 kV to 80 kV). A vacuum spark gap and a thyratron have been chosen for test and evaluation as candidate switches for the abort modulator. Modulator design, switching time delay, jitter and pre-fire data are presented.

  1. Introduction of Break-Out Session 2 of the 2011 International PV Module Quality Assurance Forum(Presentation)

    SciTech Connect

    Wohlgemuth, J.; Kurtz, S.; Sample, T.; Yamamichi, M.

    2011-07-01

    This presentation outlines the goals and specific tasks of break-out session 2 of the 2011 International PV Module Quality Assurance Forum, along with a review of accelerated stress tests used for photovoltaics (PV).

  2. Report of an exploratory study: safety and liability considerations for photovoltaic modules/panels, Low Cost Solar Array Project

    SciTech Connect

    Weinstein, A.S.; Meeker, D.G.

    1981-01-01

    Product safety and product liability considerations are explored for photovoltaic module/array devices. A general review of photovoltaic literature was made using computerized literature searches. A literature search was also made of relevant legal material as it applies to design. Recommendations are made to minimize or eliminate perceived hazards in manufacture and use of a photovoltaic module/array. (MHR)

  3. Module 3 - Project Scheduling | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3 - Project Scheduling Module 3 - Project Scheduling This module focuses on developing the project schedule. This module differentiates between planning and scheduling and outlines basic scheduling concepts, the logic relationships and critical path, and different schedule formats. Begin Module >> (816.67

  4. Module 4 - Budgeting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    4 - Budgeting Module 4 - Budgeting This module focuses on developing the cost baseline. This module outlines basic costing concepts such as control accounts, work packages and planning packages. Additionally, elements of an earned value contract baseline and proposed cost and contract budget baseline are covered. Begin Module >> (599.3

  5. Module 8 - Reporting | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    8 - Reporting Module 8 - Reporting This module focuses on the reporting options and requirement of earned value. This module illustrates and defines the different cost performance reports (CPR) available for reporting earned value information. Begin Module >> (373.58

  6. Document Reviews

    Energy.gov [DOE]

    The Office of Document Reviews, within the Office of Health, Safety and Security information and document declassification efforts promote the release of information needed by an informed citizenry...

  7. Environmental Review

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Environmental-Review Sign In About | Careers | Contact | Investors | bpa.gov Search News & Us Expand News & Us Projects & Initiatives Expand Projects & Initiatives Finance...

  8. Laser frequency modulator for modulating a laser cavity

    DOEpatents

    Erbert, Gaylen V.

    1992-01-01

    The present invention relates to a laser frequency modulator for modulating a laser cavity. It is known in the prior art to utilize a PZT (piezoelectric transducer) element in combination with a mirror to change the cavity length of a laser cavity (which changes the laser frequency). Using a PZT element to drive the mirror directly is adequate at frequencies below 10 kHz. However, in high frequency applications (100 kHz and higher) PZT elements alone do not provide a sufficient change in the cavity length. The present invention utilizes an ultrasonic concentrator with a PZT element and mirror to provide modulation of the laser cavity. With an ultrasonic concentrator, the mirror element at the end of a laser cavity can move at larger amplitudes and higher frequencies.

  9. Apparatus for encapsulating a photovoltaic module

    DOEpatents

    Albright, Scot P.; Dugan, Larry M.

    1995-10-24

    The subject inventions concern various photovoltaic module designs to protect the module from horizontal and vertical impacts and degradation of solar cell efficiency caused by moisture. In one design, a plurality of panel supports that are positioned adjacent to the upper panel in a photovoltaic module absorb vertical forces exerted along an axis perpendicular to the upper panel. Other designs employ layers of glass and tempered glass, respectively, to protect the module from vertical impacts. A plurality of button-shaped channels is used around the edges of the photovoltaic module to absorb forces applied to the module along an axis parallel to the module and direct moisture away from the module that could otherwise penetrate the module and adversely affect the cells within the module. A spacer is employed between the upper and lower panels that has a coefficient of thermal expansion substantially equivalent to the coefficient of thermal expansion of at least one of the panels.

  10. Compact nanomechanical plasmonic phase modulators

    SciTech Connect

    Dennis, B. S.; Haftel, M. I.; Czaplewski, D. A.; Lopez, D.; Blumberg, G.; Aksyuk, V. A.

    2015-03-30

    Highly confined optical energy in plasmonic devices is advancing miniaturization in photonics. However, for mode sizes approaching ≈10 nm, the energy increasingly shifts into the metal, raising losses and hindering active phase modulation. Here, we propose a nanoelectromechanical phase-modulation principle exploiting the extraordinarily strong dependence of the phase velocity of metal–insulator–metal gap plasmons on dynamically variable gap size. We experimentally demonstrate a 23-μm-long non-resonant modulator having a 1.5π rad range, with 1.7 dB excess loss at 780 nm. Analysis shows that by simultaneously decreasing the gap, length and width, an ultracompact-footprint π rad phase modulator can be realized. This is achieved without incurring the extra loss expected for plasmons confined in a decreasing gap, because the increasing phase-modulation strength from a narrowing gap offsets rising propagation losses. Such small, high-density electrically controllable components may find applications in optical switch fabrics and reconfigurable plasmonic optics.

  11. NEMS integrating module documentation report

    SciTech Connect

    Not Available

    1993-12-14

    The National Energy Modeling System (NEMS) is a computer modeling system that produces a general equilibrium solution for energy supply and demand in the US energy markets. The model achieves a supply and demand balance in the end-use demand regions, defined as the nine Census Divisions, by solving for the prices of each energy type such that the quantities producers are willing to supply equal the quantities consumers wish to consume. The system reflects market economics, industry structure, and energy policies and regulations that influence market behavior. The NEMS Integrating Module is the central integrating component of a complex modeling system. As such, a thorough understanding of its role in the modeling process can only be achieved by placing it in the proper context with respect to the other modules. To that end, this document provides an overview of the complete NEMS model, and includes brief descriptions of the modules with which the Integrating Module interacts. The emphasis and focus, however, is on the structure and function of the Integrating Module of NEMS.

  12. Reflective coherent spatial light modulator

    DOEpatents

    Simpson, John T.; Richards, Roger K.; Hutchinson, Donald P.; Simpson, Marcus L.

    2003-04-22

    A reflective coherent spatial light modulator (RCSLM) includes a subwavelength resonant grating structure (SWS), the SWS including at least one subwavelength resonant grating layer (SWL) have a plurality of areas defining a plurality of pixels. Each pixel represents an area capable of individual control of its reflective response. A structure for modulating the resonant reflective response of at least one pixel is provided. The structure for modulating can include at least one electro-optic layer in optical contact with the SWS. The RCSLM is scalable in both pixel size and wavelength. A method for forming a RCSLM includes the steps of selecting a waveguide material and forming a SWS in the waveguide material, the SWS formed from at least one SWL, the SWL having a plurality of areas defining a plurality of pixels.

  13. Solid-state membrane module

    DOEpatents

    Gordon, John Howard; Taylor, Dale M.

    2011-06-07

    Solid-state membrane modules comprising at least one membrane unit, where the membrane unit has a dense mixed conducting oxide layer, and at least one conduit or manifold wherein the conduit or manifold comprises a dense layer and at least one of a porous layer and a slotted layer contiguous with the dense layer. The solid-state membrane modules may be used to carry out a variety of processes including the separating of any ionizable component from a feedstream wherein such ionizable component is capable of being transported through a dense mixed conducting oxide layer of the membrane units making up the membrane modules. For ease of construction, the membrane units may be planar.

  14. Active combustion flow modulation valve

    DOEpatents

    Hensel, John Peter; Black, Nathaniel; Thorton, Jimmy Dean; Vipperman, Jeffrey Stuart; Lambeth, David N; Clark, William W

    2013-09-24

    A flow modulation valve has a slidably translating hollow armature with at least one energizable coil wound around and fixably attached to the hollow armature. The energizable coil or coils are influenced by at least one permanent magnet surrounding the hollow armature and supported by an outer casing. Lorentz forces on the energizable coils which are translated to the hollow armature, increase or decrease the flow area to provide flow throttling action. The extent of hollow armature translation depends on the value of current supplied and the direction of translation depends on the direction of current flow. The compact nature of the flow modulation valve combined with the high forces afforded by the actuator design provide a flow modulation valve which is highly responsive to high-rate input control signals.

  15. Programmable Multi-Chip Module

    DOEpatents

    Kautz, David; Morgenstern, Howard; Blazek, Roy J.

    2005-05-24

    A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

  16. Programmable Multi-Chip Module

    DOEpatents

    Kautz, David; Morgenstern, Howard; Blazek, Roy J.

    2004-11-16

    A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

  17. Programmable multi-chip module

    DOEpatents

    Kautz, David; Morgenstern, Howard; Blazek, Roy J.

    2004-03-02

    A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

  18. Commercial Demand Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components.

  19. Coal Market Module - NEMS Documentation

    Reports and Publications

    2014-01-01

    Documents the objectives and the conceptual and methodological approach used in the development of the National Energy Modeling System's (NEMS) Coal Market Module (CMM) used to develop the Annual Energy Outlook 2014 (AEO2014). This report catalogues and describes the assumptions, methodology, estimation techniques, and source code of CMM's two submodules. These are the Coal Production Submodule (CPS) and the Coal Distribution Submodule (CDS).

  20. Polynomial Beam Element Analysis Module

    Energy Science and Technology Software Center

    2013-05-01

    pBEAM (Polynomial Beam Element Analysis Module) is a finite element code for beam-like structures. The methodology uses Euler? Bernoulli beam elements with 12 degrees of freedom (3 translation and 3 rotational at each end of the element).

  1. WRAP module 1 treatment plan

    SciTech Connect

    Mayancsik, B.A.

    1995-05-01

    This document provides the methodology to treat waste in the Waste Receiving and Processing Module 1 facility to meet the Resource Conservation and Recovery Act (RCRA) land disposal restrictions or the Waste Isolation and Pilot Plant waste acceptance criteria. This includes Low-Level Mixed Waste, Transuranic Waste, and Transuranic Mixed Waste.

  2. Modulation compression for short wavelength harmonic generation

    SciTech Connect

    Qiang, J.

    2010-01-11

    Laser modulator is used to seed free electron lasers. In this paper, we propose a scheme to compress the initial laser modulation in the longitudinal phase space by using two opposite sign bunch compressors and two opposite sign energy chirpers. This scheme could potentially reduce the initial modulation wavelength by a factor of C and increase the energy modulation amplitude by a factor of C, where C is the compression factor of the first bunch compressor. Such a compressed energy modulation can be directly used to generate short wavelength current modulation with a large bunching factor.

  3. Microsoft Word - RM Procedures.doc

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    80 percent of the box containing classified records. 02012010 RECORDS RETRIEVAL ACCESS MEMO: 1. To gain admittance to the RHA, or request records from WNRC an email must be...

  4. High Performance Sustainable Building Design RM

    Office of Environmental Management (EM)

    and Project Management for the Acquisition of Capital Assets, DOE-STD-1189-2008, Integration of Safety into the Design Process, and EM's internal business management practices. ...

  5. Safeguards and Security and Cyber Security RM

    Office of Environmental Management (EM)

    and Project Management for the Acquisition of Capital Assets, DOE-STD-1189-2008, Integration of Safety into the Design Process, and EM's internal business management practices. ...

  6. Construction Project Safety and Health Plan RM

    Office of Environmental Management (EM)

    5.4 May 2016 1 Congressional Notifications [References: FAR 5.403 and "Guide for Congressional and Intergovernmental Notifications" (Sep 2014), issued via DOE Deputy Secretary Memorandum (Oct 1, 2014)] 1.0 Summary of Latest Changes This update: (1) deletes the requirement for separate reporting of the final Request for Proposal (RFP) over $25 million via a "Solicitation Notification" form, (2) establishes that RFPs over $25 million are reported via "Priority

  7. Energy Review

    Annual Energy Outlook

    M iggl-003504t11l)sar Energy Review 8 M. IM W I -W All* r ;ai*i el I gi In this issue: Energy-related housing characteristics Propane-provider fleet survey Ordering...

  8. Quarterly Review

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    3, 2009 Federal Columbia River Power System (FCRPS) FY 2009 FIRST QUARTER REVIEW Projection for FY 2009 Net Revenues and Reserves A B C D FY 2008 Audited Actuals without FAS 133 &...

  9. A Review

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Review of the Department of Energy's Implementation of Executive Order 12898 and Recommendations for a Second Five-Year Strategic Plan Submitted by: Office of Public Information and Community Outreach Medical University of South Carolina Charleston, South Carolina 12898 12898 A Review of the U.S. Department of Energy's Implementation of Executive Order 12898 and Recommendations for a Second Five-Year Strategic Plan Table of Contents Introduction

  10. Beam Propagator for Weather Radars, Modules 1 and 2

    Energy Science and Technology Software Center

    2013-10-08

    This program simulates the beam propagation of weather radar pulses under particular and realistic atmospheric conditions (without using the assumption of standard refraction conditions). It consists of two modules: radiosondings_refract_index_many.pro (MAIN MODULE) beam_propagation_function.pro(EXTERNAL FUNCTION) FOR THE MAIN MODULE, THE CODE DOES OUTPUT--INTO A FILE--THE BEAM HEIGHT AS A FUNCTION OF RANGE. THE RADIOSONDE INPUT FILES SHOULD BE ALREADY AVAILABLE BY THE USER. FOR EXAMPLE, RADIOSONDE OBSERVATION FILES CAN BE OBTAINED AT: RADIOSONDE OBSERVATIONS DOWNLOADED ATmore » "http://weather.uwyo.edu/upperair/soounding.html" OR "http://jervis.pyr.ec.gc.ca" THE EXTERNAL FUNCTION DOES THE ACTUAL COMPUTATION OF BEAM PROPAGATION. IT INCLUDES CONDITIONS OF ANOMALOUS PROPAGATION AND NEGATIVE ELEVATION ANGLES. THE EQUATIONS USED HERE WERE DERIVED BY EDWIN CAMPOS, BASED ON THE SNELL-DESCARTES LAW OF REFRACTION, CONSIDERING THE EARTH CURVATURE. THE PROGRAM REQUIRES A COMPILER FOR THE INTERACTIVE DATA LANGUAGE (IDL). DESCRIPTION AND VALIDATION DETAILS HAVE BEEN PUBLISHED IN THE PEER-REVIEWED SCIENTIFIC LITERATURE, AS FOLLOWS: Campos E. 2012. Estimating weather radar coverage over complex terrain, pp.26-32, peer reviewed, in Weather Radar and Hydrology, edited by Moore RJ, Cole SJ and Illingworth AJ. International Association of Hydrological Sciences (IAHS) Press, IAHS Publ. 351. ISBN 978-1-907161-26-1.« less

  11. Standards for PV Modules and Components -- Recent Developments and Challenges: Preprint

    SciTech Connect

    Wohlgemuth, J. H.

    2012-10-01

    International standards play an important role in the Photovoltaic industry. Since PV is such a global industry it is critical that PV products be measured and qualified the same way everywhere in the world. IEC TC82 has developed and published a number of module and component measurement and qualification standards. These are continually being updated to take advantage of new techniques and equipment as well as better understanding of test requirements. Standards presently being updated include the third edition of IEC 61215, Crystalline Silicon Qualification and the second edition of IEC 61730, PV Module Safety Requirements. New standards under development include qualification of junction boxes, connectors, PV cables, and module integrated electronics as well as for testing the packaging used during transport of modules. After many years of effort, a draft standard on Module Energy Rating should be circulated for review soon. New activities have been undertaken to develop standards for the materials within a module and to develop tests that evaluate modules for wear-out in the field (International PV Module QA Task Force). This paper will discuss these efforts and indicate how the audience can participate in development of international standards.

  12. Interface module for transverse energy input to dye laser modules

    DOEpatents

    English, Jr., Ronald E.; Johnson, Steve A.

    1994-01-01

    An interface module (10) for transverse energy input to dye laser modules is provided particularly for the purpose of delivering enhancing transverse energy beams (36) in the form of illumination bar (54) to the lasing zone (18) of a dye laser device, in particular to a dye laser amplifier (12). The preferred interface module (10) includes an optical fiber array (30) having a plurality of optical fibers (38) arrayed in a co-planar fashion with their distal ends (44) receiving coherent laser energy from an enhancing laser source (46), and their proximal ends (4) delivered into a relay structure (3). The proximal ends (42) of the optical fibers (38) are arrayed so as to be coplanar and to be aimed generally at a common point. The transverse energy beam array (36) delivered from the optical fiber array (30) is acted upon by an optical element array (34) to produce an illumination bar (54) which has a cross section in the form of a elongated rectangle at the position of the lasing window (18). The illumination bar (54) is selected to have substantially uniform intensity throughout.

  13. Interface module for transverse energy input to dye laser modules

    DOEpatents

    English, R.E. Jr.; Johnson, S.A.

    1994-10-11

    An interface module for transverse energy input to dye laser modules is provided particularly for the purpose of delivering enhancing transverse energy beams in the form of illumination bar to the lasing zone of a dye laser device, in particular to a dye laser amplifier. The preferred interface module includes an optical fiber array having a plurality of optical fibers arrayed in a co-planar fashion with their distal ends receiving coherent laser energy from an enhancing laser source, and their proximal ends delivered into a relay structure. The proximal ends of the optical fibers are arrayed so as to be coplanar and to be aimed generally at a common point. The transverse energy beam array delivered from the optical fiber array is acted upon by an optical element array to produce an illumination bar which has a cross section in the form of a elongated rectangle at the position of the lasing window. The illumination bar is selected to have substantially uniform intensity throughout. 5 figs.

  14. PV module mounting method and mounting assembly

    DOEpatents

    Lenox, Carl J.S.; Johnson, Kurt M.

    2013-04-23

    A method for mounting PV modules to a deck includes selecting PV module layout pattern so that adjacent PV module edges are spaced apart. PV mounting and support assemblies are secured to the deck according to the layout pattern using fasteners extending into the deck. The PV modules are placed on the PV mounting and support assemblies. Retaining elements are located over and secured against the upper peripheral edge surfaces of the PV modules so to secure them to the deck with the peripheral edges of the PV modules spaced apart from the deck. In some examples a PV module mounting assembly, for use on a shingled deck, comprises flashing, a base mountable on the flashing, a deck-penetrating fastener engageable with the base and securable to the deck so to secure the flashing and the base to the shingled deck, and PV module mounting hardware securable to the base.

  15. Mounting support for a photovoltaic module

    DOEpatents

    Brandt, Gregory Michael; Barsun, Stephan K.; Coleman, Nathaniel T.; Zhou, Yin

    2013-03-26

    A mounting support for a photovoltaic module is described. The mounting support includes a foundation having an integrated wire-way ledge portion. A photovoltaic module support mechanism is coupled with the foundation.

  16. Extension Modules for the Python Interpretive language

    Energy Science and Technology Software Center

    2006-12-29

    Python is an interpreted computer language, freely available to all, which may be extended by user developed "modules". These modules ay be written in a complied language such as 'C', and then linked into the Python program

  17. Reliability Issues for Photovoltaic Modules (Presentation)

    SciTech Connect

    Kurtz, S.

    2009-10-01

    Si modules good in field; new designs need reliability testing. CdTe & CIGS modules sensitive to moisture; carefully seal. CPV in product development stage; benefits from expertise in other industries.

  18. Tunable Surface Plasmon Infrared Modulator - Energy Innovation...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    and Industries Infrared Modulator IR Counter Measures Photonic Circuitry Metamaterials Chemical Sensing Variable Attenuation Patents and Patent Applications ID Number...

  19. Seeding Coherent Radiation Sources with Sawtooth Modulation ...

    Office of Scientific and Technical Information (OSTI)

    HARMONICS; INSTABILITY; MODULATION; PERFORMANCE; PHASE SPACE; POLARIZATION; RADIATION SOURCES; SATURATION; SEEDS; WAVE FORMS; WAVELENGTHS Accelerators,ACCPHY, SYNCHRAD, XFEL

  20. Module: Estimating Historical Emissions from Deforestation |...

    OpenEI (Open Energy Information) [EERE & EIA]

    Website: www.leafasia.orgtoolstechnical-guidance-series-estimating-historical Cost: Free Language: English Module: Estimating Historical Emissions from Deforestation Screenshot...

  1. Table 2. Value and average value of photovoltaic module shipments...

    Energy Information Administration (EIA) (indexed site)

    Value and average value of photovoltaic module shipments, 2015" "Module value, total ... Administration, Form EIA-63B, 'Annual Photovoltaic CellModule Shipments Report' Note: ...

  2. Thermal Reliability Study of Bypass Diodes in Photovoltaic Modules...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Thermal Reliability Study of Bypass Diodes in Photovoltaic Modules Thermal Reliability Study of Bypass Diodes in Photovoltaic Modules Presented at the PV Module Reliability ...

  3. Partial Shading in Monolithic Thin Film PV Modules: Analysis...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Partial Shading in Monolithic Thin Film PV Modules: Analysis and Design Partial Shading in Monolithic Thin Film PV Modules: Analysis and Design Presented at the PV Module ...

  4. Overview of the PV Module Model in PVWatts (Presentation)

    SciTech Connect

    Marion, B.

    2010-09-22

    Overview of the PV module model. PVWatts module power estimates were compared with those using the Sandia model for three modules and data sets.

  5. Emittance growth from electron beam modulation

    SciTech Connect

    Blaskiewicz, M.

    2009-12-01

    In linac ring colliders like MeRHIC and eRHIC a modulation of the electron bunch can lead to a modulation of the beam beam tune shift and steering errors. These modulations can lead to emittance growth. This note presents simple formulas to estimate these effects which generalize some previous results.

  6. A Stability of LCLS Linac Modulators

    SciTech Connect

    Decker, F.-J.; Krasnykh, A.; Morris, B.; Nguyen, M.; /SLAC

    2012-06-13

    Information concerning to a stability of LCLS RF linac modulators is allocated in this paper. In general a 'pulse-to-pulse' modulator stability (and RF phase as well) is acceptable for the LCLS commission and FEL programs. Further modulator stability improvements are possible and approaches are discussed based on our experimental results.

  7. Development of GREET Catalyst Module

    SciTech Connect

    Wang, Zhichao; Benavides, Pahola T.; Dunn, Jennifer B.; Cronauer, Donald C.

    2015-09-01

    In this report, we develop energy and material flows for the production of five different catalysts (tar reforming, alcohol synthesis, Zeolite Socony Mobil-5 [ZSM-5], Mo/Co/ γ-Al2O3, and Pt/ γ-Al2O3) and two chemicals (olivine, dimethyl ether of polyethylene glycol [DEPG]). These compounds and catalysts are now included in the Greenhouse Gases, Regulated Emissions and Energy Use in Transportation (GREET™) catalyst module.

  8. Solid-state membrane module

    SciTech Connect

    Hinklin, Thomas Ray; Lewinsohn, Charles Arthur

    2015-06-30

    A module for separating oxygen from an oxygen-containing gaseous mixture comprising planar solid-state membrane units, each membrane unit comprising planar dense mixed conducting oxides layers, planar channel-free porous support layers, and one or more planar intermediate support layers comprising at least one channeled porous support layer. The porosity of the planar channeled porous support layers is less than the porosity of the planar channel-free porous support layers.

  9. Pulse amplitude modulated chlorophyll fluorometer

    DOEpatents

    Greenbaum, Elias; Wu, Jie

    2015-12-29

    Chlorophyll fluorometry may be used for detecting toxins in a sample because of changes in micro algae. A portable lab on a chip ("LOAC") based chlorophyll fluorometer may be used for toxin detection and environmental monitoring. In particular, the system may include a microfluidic pulse amplitude modulated ("PAM") chlorophyll fluorometer. The LOAC PAM chlorophyll fluorometer may analyze microalgae and cyanobacteria that grow naturally in source drinking water.

  10. Gas separation membrane module assembly

    DOEpatents

    Wynn, Nicholas P; Fulton, Donald A.

    2009-03-31

    A gas-separation membrane module assembly and a gas-separation process using the assembly. The assembly includes a set of tubes, each containing gas-separation membranes, arranged within a housing. The housing contains a tube sheet that divides the space within the housing into two gas-tight spaces. A permeate collection system within the housing gathers permeate gas from the tubes for discharge from the housing.

  11. Analytical Review

    SciTech Connect

    Frank Stodolsky

    2000-04-11

    ANL Performs Independent Review for DOE on the following topics: (1) Systematic analysis--Depends on question asked; (2) Compare technologies and pathways--Examples: (a) fuels, power plant technologies, vehicle materials; (b) Total lifecycle analysis reveals national and global impacts; and (3) Direction of R&D to most fruitful areas.

  12. Argonne's SpEC Module | Argonne National Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    SpEC Module Share Topic Energy Energy efficiency Vehicles

  13. Photovoltaic module certification/laboratory accreditation criteria development

    SciTech Connect

    Osterwald, C.R. [National Renewable Energy Lab., Golden, CO (United States); Hammond, R.L.; Wood, B.D.; Backus, C.E.; Sears, R.L. [Arizona State Univ., Tempe, AZ (United States); Zerlaut, G.A. [SC-International Inc., Phoenix, AZ (United States); D`Aiello, R.V. [RD Associates, Tempe, AZ (United States)

    1995-04-01

    This document provides an overview of the structure and function of typical product certification/laboratory accreditation programs. The overview is followed by a model program which could serve as the basis for a photovoltaic (PV) module certification/laboratory accreditation program. The model covers quality assurance procedures for the testing laboratory and manufacturer, third-party certification and labeling, and testing requirements (performance and reliability). A 30-member Criteria Development Committee was established to guide, review, and reach a majority consensus regarding criteria for a PV certification/laboratory accreditation program. Committee members represented PV manufacturers, end users, standards and codes organizations, and testing laboratories.

  14. Microsoft PowerPoint - User Experience with Module Performance...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Private & Confidential Generating Change Since 1980 User Experience with Module ... Private & Confidential User Experience with Module Performance Coefficients ...

  15. FES Requirements Review 2014

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    FES Requirements Review 2014 Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials FAQ for Case Study Authors BER Requirements Review 2015 ASCR Requirements Review 2015 Previous Reviews HEP/NP Requirements Review 2013 FES Requirements Review 2014 FES Attendees 2014 BES Requirements Review 2014 Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1

  16. BES Requirements Review 2014

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    BES Requirements Review 2014 Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials FAQ for Case Study Authors BER Requirements Review 2015 ASCR Requirements Review 2015 Previous Reviews HEP/NP Requirements Review 2013 FES Requirements Review 2014 BES Requirements Review 2014 BES Attendees 2014 Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1

  17. Electrostatically actuatable light modulating device

    DOEpatents

    Koehler, Dale R.

    1991-01-01

    The electrostatically actuatable light modulator utilizes an opaque substrate plate patterned with an array of aperture cells, the cells comprised of physically positionable dielectric shutters and electrostatic actuators. With incorporation of a light source and a viewing screen, a projection display system is effected. Inclusion of a color filter array aligned with the aperture cells accomplishes a color display. The system is realized in terms of a silicon based manufacturing technology allowing fabrication of a high resolution capability in a physically small device which with the utilization of included magnification optics allows both large and small projection displays.

  18. Highly Sensitive Electro-Optic Modulators

    SciTech Connect

    DeVore, Peter S

    2015-10-26

    There are very important diagnostic and communication applications that receive faint electrical signals to be transmitted over long distances for capture. Optical links reduce bandwidth and distance restrictions of metal transmission lines; however, such signals are only weakly imprinted onto the optical carrier, resulting in low fidelity transmission. Increasing signal fidelity often necessitates insertion of radio-frequency (RF) amplifiers before the electro-optic modulator, but (especially at high frequencies) RF amplification results in large irreversible distortions. We have investigated the feasibility of a Sensitive and Linear Modulation by Optical Nonlinearity (SALMON) modulator to supersede RF-amplified modulators. SALMON uses cross-phase modulation, a manifestation of the Kerr effect, to enhance the modulation depth of an RF-modulated optical wave. This ultrafast process has the potential to result in less irreversible distortions as compared to a RF-amplified modulator due to the broadband nature of the Kerr effect. Here, we prove that a SALMON modulator is a feasible alternative to an RFamplified modulator, by demonstrating a sensitivity enhancement factor greater than 20 and significantly reduced distortion.

  19. Binary module test. Final report

    SciTech Connect

    Schilling, J.R.; Colley, T.C.; Pundyk, J.

    1980-12-01

    The objective of this project was to design and test a binary loop module representative of and scaleable to commercial size units. The design was based on state-of-the-art heat exchanger technology, and the purpose of the tests was to confirm performance of a supercritical boiling cycle using isobutane and a mixture of isobutane and isopentane as the secondary working fluid. The module was designed as one percent of a 50 MW unit. It was installed at Magma Power's East Mesa geothermal field and tested over a period of approximately 4 months. Most of the test runs were with isobutane but some data were collected for hydrocarbon mixtures. The results of the field tests are reported. In general these results indicate reasonably good heat balances and agreement with overall heat transfer coefficients calculated by current stream analysis methods and available fluid property data; however, measured pressure drops across the heat exchangers were 20 percent higher than estimated. System operation was stable under all conditions tested.

  20. In-Line Thermoelectric Module

    SciTech Connect

    Pento, Robert; Marks, James E.; Staffanson, Clifford D.

    1998-07-28

    A thermoelectric module with a plurality of electricity generating units each having a first end and a second end, the units being arranged first end to second end along an-in-line axis. Each unit includes first and second elements each made of a thermoelectric material, an electrically conductive hot member arranged to heat one side of the first element, and an electrically conductive cold member arranged to cool another side of the first element and to cool one side of the second element. The hot member, the first element, the cold member and the second element are supported in a fixture, are electrically connected respectively to provide an electricity generating unit, and are arranged respectively in positions along the in-line axis. The individual components of each generating unit and the respective generating units are clamped in their in-line positions by a loading bolt at one end of the fixture and a stop wall at the other end of the fixture. The hot members may have a T-shape and the cold members an hourglass shape to facilitate heat transfer. The direction of heat transfer through the hot members may be perpendicular to the direction of heat transfer through the cold members, and both of these heat transfer directions maybe perpendicular to the direction-of current flow through the module.

  1. In-line thermoelectric module

    DOEpatents

    Pento, Robert; Marks, James E.; Staffanson, Clifford D.

    2000-01-01

    A thermoelectric module with a plurality of electricity generating units each having a first end and a second end, the units being arranged first end to second end along an in-line axis. Each unit includes first and second elements each made of a thermoelectric material, an electrically conductive hot member arranged to heat one side of the first element, and an electrically conductive cold member arranged to cool another side of the first element and to cool one side of the second element. The hot member, the first element, the cold member and the second element are supported in a fixture, are electrically connected respectively to provide an electricity generating unit, and are arranged respectively in positions along the in-line axis. The individual components of each generating unit and the respective generating units are clamped in their in-line positions by a loading bolt at one end of the fixture and a stop wall at the other end of the fixture. The hot members may have a T-shape and the cold members an hourglass shape to facilitate heat transfer. The direction of heat transfer through the hot members may be perpendicular to the direction of heat transfer through the cold members, and both of these heat transfer directions may be perpendicular to the direction of current flow through the module.

  2. Smart Fan Modules And System

    DOEpatents

    Cipolla, Thomas M.; Kaufman, Richard I.; Mok, Lawrence S.

    2003-07-15

    A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals. A fan module including: two or more individual fans, each fan having an air movement means and a motor engaged with the air movement means for accelerating air entering each of the two or more individual fans; a temperature sensor for sensing a temperature associated with the two or more fans and for outputting a first signal corresponding to the temperature; rotational speed sensor for outputting a second signal corresponding to a rotational speed of each of the two or more fans; and a processor for receiving the first and second signals and controlling the two or more individual fans based on the first and second signals.

  3. Data quality objectives for Ion Exchange Module (IXM) disposition

    SciTech Connect

    Choi, I.

    1995-01-31

    This Data Quality Objective (DQO) document presents the data needs and accuracy requirements for sampling ion exchange modules at the K Basins, 100 K Area, to determine if there is a hydrogen gas buildup within the modules. This document was produced by PNL, with the assistance of Neptune and Associates, and was partly funded (for facilitator) by DOE-HQ as a demonstration DQO for EM activities. PNL involved a number of PNL, WHC and support contract staff (including external technical consultants) in meetings to define the data needed, along with the necessary accuracy, to resolve issues associated with hydrogen accumulation in Ion Exchange Modules (IXMS) that were generated prior to July 1994 and only have one nuc-fil vent. IXMs generated after July 1994 have multiple nuc-fil vents and do not require sampling. PNL transmitted this DQO to WHC on January 31, 1995. This Supporting Document is to assure that the document is captured into the document retrieval system. WHC review focused on the acceptability of the technical conclusions such that the data collected will meet minimum operational, safety and environmental needs.

  4. Power module assemblies with staggered coolant channels

    DOEpatents

    Herron, Nicholas Hayden; Mann, Brooks S; Korich, Mark D

    2013-07-16

    A manifold is provided for supporting a power module assembly with a plurality of power modules. The manifold includes a first manifold section. The first face of the first manifold section is configured to receive the first power module, and the second face of the first manifold section defines a first cavity with a first baseplate thermally coupled to the first power module. The first face of the second manifold section is configured to receive the second power module, and the second face of the second manifold section defines a second cavity with a second baseplate thermally coupled to the second power module. The second face of the first manifold section and the second face of the second manifold section are coupled together such that the first cavity and the second cavity form a coolant channel. The first cavity is at least partially staggered with respect to second cavity.

  5. An ultrafast carbon nanotube terahertz polarisation modulator

    SciTech Connect

    Docherty, Callum J.; Stranks, Samuel D.; Habisreutinger, Severin N.; Joyce, Hannah J.; Herz, Laura M.; Nicholas, Robin J.; Johnston, Michael B.

    2014-05-28

    We demonstrate ultrafast modulation of terahertz radiation by unaligned optically pumped single-walled carbon nanotubes. Photoexcitation by an ultrafast optical pump pulse induces transient terahertz absorption in nanowires aligned parallel to the optical pump. By controlling the polarisation of the optical pump, we show that terahertz polarisation and modulation can be tuned, allowing sub-picosecond modulation of terahertz radiation. Such speeds suggest potential for semiconductor nanowire devices in terahertz communication technologies.

  6. BER Requirements Review 2015

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reviews Network Requirements Reviews Documents and Background Materials FAQ for Case Study Authors BER Requirements Review 2015 BER Attendees 2015 ASCR Requirements...

  7. Module Encapsulation Materials, Processing and Testing (Presentation...

    Office of Scientific and Technical Information (OSTI)

    Country of Publication: United States Language: English Subject: 14 SOLAR ENERGY; 36 MATERIALS SCIENCE; ENCAPSULATION; PROCESSING; RELIABILITY; TESTING PV; MODULE ENCAPSULATION; ...

  8. Integrated Performance Testing Workshop, Modules 6 - 11

    SciTech Connect

    Leach, Janice; Torres, Teresa M.

    2012-10-01

    These modules cover performance testing of: Interior Detection Systems; Access Controls; Exterior Detection Systems; Video Assessment Systems; SNM / Contraband Detection Systems; Access Delay Elements

  9. Dense optical-electrical interface module

    SciTech Connect

    Paul Chang

    2000-12-21

    The DOIM (Dense Optical-electrical Interface Modules) is a custom-designed optical data transmission module employed in the upgrade of Silicon Vertex Detector of CDF experiment at Fermilab. Each DOIM module consists of a transmitter (TX) converting electrical differential input signals to optical outputs, a middle segment of jacketed fiber ribbon cable, and a receiver (RX) which senses the light inputs and converts them back to electrical signals. The targeted operational frequency is 53 MHz, and higher rate is achievable. This article outlines the design goals, implementation methods, production test results, and radiation hardness tests of these modules.

  10. PROJECT PROFILE: Support of International Photovoltaic Module...

    Energy.gov [DOE] (indexed site)

    This project supports the National Renewable Energy Laboratory's involvement in the Photovoltaic (PV) Module Quality Assurance Task Force (PVQAT) to develop the international test ...

  11. Natural Gas Transmission and Distribution Module

    Energy Information Administration (EIA) (indexed site)

    July 31, 2012, Washington, DC Major assumption changes for AEO2013 Oil and Gas Working Group Natural Gas Transmission and Distribution Module DRAFT WORKING GROUP PRESENTATION DO ...

  12. SHARP Physics Modules Updated | Department of Energy

    Energy Saver

    Nek5000, SHARP's thermal fluids module, provides solvers for multi-dimensional heat transfer and fluid dynamics. In the second quarter, an updated pressure solver was released, ...

  13. PV Cell and Module Calibrations at NREL

    SciTech Connect

    Emery, Keith

    2012-10-22

    NREL has equipment to measure any conceivable cell or module technology. The lack of standards for low concentration modules complicates matters. Spectrally adjustable simulators are critical for more than three junctions. NREL's 10-channel fiber optic simulator has shown that the light can be set for each junction within 1% of what it would be under the reference spectrum for up to a five-junction cell. Uncertainty in module simulators dominated by spatial nonuniformity for calibration labs. Manufacturers can mitigate this error by using matched reference modules instead of cells.

  14. Encapsulation of High Temperature Thermoelectric Modules

    Energy.gov [DOE]

    Presents concept for hermetic encapsulation of TE modules addressing key failure mechanism, TE material oxidation, which severely impacts long term performance

  15. Optical sensing based on wavelength modulation spectroscopy

    DOEpatents

    Buckley, Steven G.; Gharavi, Mohammadreza; Borchers; Marco

    2011-06-28

    Techniques, apparatus and systems for using Wavelength Modulation Spectroscopy measurements to optically monitor gas media such as gases in gas combustion chambers.

  16. Electrochemically-Modulated Separation and Mass Spectrometric...

    Office of Scientific and Technical Information (OSTI)

    Electrochemically-modulated separations (EMS) are a straightforward means of isolating and pre-concentrating elements for on-line mass spectrometric analysis. Elements are ...

  17. NREL: Measurements and Characterization - Outdoor Module Current...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    of prototype concentrator modules and cells mounted in a 2-axis tracker; translation equations, stability and performance of concentrator Up to 10 samples at a time;...

  18. Alternative Energy Sources - An Interdisciplinary Module for...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    An Interdisciplinary Module for Energy Education Alternative Energy Sources - An ... Energy Basics, Wind Energy, Solar Summary Find activities focused on renewable energy ...

  19. Alternative Energy Sources - An Interdisciplinary Module for...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Alternative Energy Sources - An Interdisciplinary Module for Energy Education Alternative ... Energy Basics, Wind Energy, Solar Summary: Find activities focused on renewable energy ...

  20. Solid State Marx Modulators for Emerging Applications

    SciTech Connect

    Kemp, M.A.; /SLAC

    2012-09-14

    Emerging linear accelerator applications increasingly push the boundaries of RF system performance and economics. The power modulator is an integral part of RF systems whose characteristics play a key role in the determining parameters such as efficiency, footprint, cost, stability, and availability. Particularly within the past decade, solid-state switch based modulators have become the standard in high-performance, high power modulators. One topology, the Marx modulator, has characteristics which make it particularly attractive for several emerging applications. This paper is an overview of the Marx topology, some recent developments, and a case study of how this architecture can be applied to a few proposed linear accelerators.

  1. PROJECT PROFILE: Cell and Module Performance Characterization...

    Energy.gov [DOE] (indexed site)

    The project supports the cell and module measurement lab at NREL, which provides the only recognized, accredited efficiency measurements in the U.S. for the photovoltaic (PV) ...

  2. Casks (computer analysis of storage casks): A microcomputer based analysis system for storage cask review

    SciTech Connect

    Chen, T.F.; Mok, G.C.; Carlson, R.W.

    1995-08-01

    CASKS is a microcomputer based computer system developed by LLNL to assist the Nuclear Regulatory Commission in performing confirmatory analyses for licensing review of radioactive-material storage cask designs. The analysis programs of the CASKS computer system consist of four modules: the impact analysis module, the thermal analysis module, the thermally-induced stress analysis module, and the pressure-induced stress analysis module. CASKS uses a series of menus to coordinate input programs, cask analysis programs, output programs, data archive programs and databases, so the user is able to run the system in an interactive environment. This paper outlines the theoretical background on the impact analysis module and the yielding surface formulation. The close agreement between the CASKS analytical predictions and the results obtained form the two storage casks drop tests performed by SNL and by BNFL at Winfrith serves as the validation of the CASKS impact analysis module.

  3. Progress in the Long $${\\rm Nb}_{3}{\\rm Sn}$$ Quadrupole R&D by LARP

    DOE PAGES [OSTI]

    Ambrosio, G.; Andreev, N.; Anerella, M.; Barzi, E.; Bocian, D.; Bossert, R.; Buehler, M.; Caspi, S.; Chlachidze, G.; Dietderich, D.; et al

    2011-11-14

    After the successful test of the first long Nb3Sn quadrupole (LQS01) the US LHC Accelerator Research Program (LARP, a collaboration of BNL, FNAL, LBNL and SLAC) is assessing training memory, reproducibility, and other accelerator quality features of long Nb3Sn quadrupole magnets. LQS01b (a reassembly of LQS01 with more uniform and higher pre-stress) was subjected to a full thermal cycle and reached the previous plateau of 222 T/m at 4.5 K in two quenches. A new set of four coils, made of the same type of conductor used in LQS01 (RRP 54/61 by Oxford Superconducting Technology), was assembled in the LQS01more » structure and tested at 4.5 K and lower temperatures. The new magnet (LQS02) reached the target gradient (200 T/m) only at 2.6 K and lower temperatures, at intermediate ramp rates. The preliminary test analysis, here reported, showed a higher instability in the limiting coil than in the other coils of LQS01 and LQS02.« less

  4. ASCR Requirements Review 2015

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ASCR Requirements Review 2015 ASCR Attendees 2015 Previous Reviews Requirements Review Reports Case Studies News & Publications ESnet News Publications and Presentations Galleries ESnet Awards and Honors Blog ESnet Live Home » Science Engagement » Science Requirements Reviews » Network Requirements Reviews » ASCR Requirements Review 2015 Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials

  5. 2008 annual merit review

    SciTech Connect

    None, None

    2009-01-18

    The 2008 DOE Vehicle Technologies Program Annual Merit Review was held February 25-28, 2008 in Bethesda, Maryland. The review encompassed all of the work done by the Vehicle Technologies Program: a total of 280 individual activities were reviewed, by a total of just over 100 reviewers. A total of 1,908 individual review responses were received for the technical reviews, and an additional 29 individual review responses were received for the plenary session review.

  6. BER Requirements Review 2015

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    BER Attendees 2015 ASCR Requirements Review 2015 Previous Reviews Requirements Review Reports Case Studies News & Publications ESnet News Publications and Presentations Galleries ESnet Awards and Honors Blog ESnet Live Home » Science Engagement » Science Requirements Reviews » Network Requirements Reviews » BER Requirements Review 2015 Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials

  7. Identification coding schemes for modulated reflectance systems

    DOEpatents

    Coates, Don M.; Briles, Scott D.; Neagley, Daniel L.; Platts, David; Clark, David D.

    2006-08-22

    An identifying coding apparatus employing modulated reflectance technology involving a base station emitting a RF signal, with a tag, located remotely from the base station, and containing at least one antenna and predetermined other passive circuit components, receiving the RF signal and reflecting back to the base station a modulated signal indicative of characteristics related to the tag.

  8. Development Status of The ILC Marx Modulator

    SciTech Connect

    Nguyen, M; Beukers, T.; Burkhart, C.; Larsen, R.; Olsen, J.; Tang, T.; /SLAC

    2010-06-07

    The ILC Marx Modulator is under development as a lower cost alternative to the 'Baseline Conceptual Design' (BCD) klystron modulator. Construction of a prototype Marx is complete and testing is underway at SLAC. The Marx employs solid state elements, IGBTs and diodes, to control the charge, discharge and isolation of the modules. The prototype is based on a stack of sixteen modules, each initially charged to {approx}11 kV, which are arranged in a Marx topology. Initially, eleven modules combine to produce the 120 kV output pulse. The remaining modules are switched in after appropriate delays to compensate for the voltage droop that results from the discharge of the energy storage capacitors. Additional elements will further regulate the output voltage to {+-}0.5%. The Marx presents several advantages over the conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at these parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. This paper outlines the current developmental status of the prototype Marx. It presents a detailed electrical and mechanical description of the modulator and operational test results. It will discuss electrical efficiency measurements, fault testing, and output voltage regulation.

  9. Development Status of the ILC Marx Modulator

    SciTech Connect

    Nguyen, M.; Beukers, T.; Burkhart, C.; Larsen, R.; Olsen, J.; Tang, T.; /SLAC

    2008-06-16

    The ILC Marx Modulator is under development as a lower cost alternative to the 'Baseline Conceptual Design' (BCD) klystron modulator. Construction of a prototype Marx is complete and testing is underway at SLAC. The Marx employs solid state elements, IGBTs and diodes, to control the charge, discharge and isolation of the modules. The prototype is based on a stack of sixteen modules, each initially charged to {approx}11 kV, which are arranged in a Marx topology. Initially, eleven modules combine to produce the 120 kV output pulse. The remaining modules are switched in after appropriate delays to compensate for the voltage droop that results from the discharge of the energy storage capacitors. Additional elements will further regulate the output voltage to {+-} 0.5%. The Marx presents several advantages over the conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at these parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. This paper outlines the current developmental status of the prototype Marx. It presents a detailed electrical and mechanical description of the modulator and operational test results. It will discuss electrical efficiency measurements, fault testing, and output voltage regulation.

  10. Testing Protocol for Module Encapsulant Creep (Presentation)

    SciTech Connect

    Kempe, M. D.; Miller, D. C.; Wohlgemuth, J. H.; Kurtz, S. R.; Moseley, J. M.; Shah, Q.; Tamizhmani, G.; Sakurai, K.; Inoue, M.; Doi, T.; Masuda, A.

    2012-02-01

    Recently there has been an interest in the use of thermoplastic encapsulant materials in photovoltaic modules to replace chemically crosslinked materials, e.g., ethylene-vinyl acetate. The related motivations include the desire to: reduce lamination time or temperature; use less moisture-permeable materials; or use materials with better corrosion characteristics. However, the use of any thermoplastic material in a high-temperature environment raises safety and performance concerns, as the standardized tests currently do not expose the modules to temperatures in excess of 85C, yet modules may experience temperatures above 100C in operation. Here we constructed eight pairs of crystalline-silicon modules and eight pairs of glass/encapsulation/glass mock modules using different encapsulation materials of which only two were designed to chemically crosslink. One module set was exposed outdoors with insulation on the back side in Arizona in the summer, and an identical set was exposed in environmental chambers. High precision creep measurements and performance measurements indicate that despite many of these polymeric materials being in the melt state at some of the highest outdoor temperatures achievable, very little creep was seen because of their high viscosity, temperature heterogeneity across the modules, and in the case of the crystalline-silicon modules, the physical restraint of the backsheet. These findings have very important implications for the development of IEC and UL qualification and safety standards, and in regards to the necessary level of cure during the processing of crosslinking encapsulants.

  11. Order Module--DOE O 425.1D, VERIFICATION OF READINESS TO START UP OR

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    RESTART NUCLEAR FACILITIES | Department of Energy 5.1D, VERIFICATION OF READINESS TO START UP OR RESTART NUCLEAR FACILITIES Order Module--DOE O 425.1D, VERIFICATION OF READINESS TO START UP OR RESTART NUCLEAR FACILITIES "The familiar level of this module is divided into three sections. In the first section we will discuss the purpose of DOE O 425.1D and the requirements for 1) determining the level of readiness review (RR), 2) determining the startup authorization authority (SAA), and

  12. Comparison of Module Performance Characterization Methods

    SciTech Connect

    KROPOSKI,B.; MARION,W.; KING,DAVID L.; BOYSON,WILLIAM EARL; KRATOCHVIL,JAY A.

    2000-10-03

    The rating and modeling of photovoltaic PW module performance has been of concern to manufacturers and system designers for over 20 years. Both the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) have developed methodologies to predict module and array performance under actual operating conditions. This paper compares the two methods of determining the performance of PV modules, The methods translate module performance to actual or reference conditions using slightly different approaches. The accuracy of both methods is compared for both hourly, daily, and annual energy production over a year of data recorded at NREL in Golden, CO. The comparison of the two methods will be presented for five different PV module technologies.

  13. Ion transport membrane module and vessel system

    DOEpatents

    Stein, VanEric Edward; Carolan, Michael Francis; Chen, Christopher M.; Armstrong, Phillip Andrew; Wahle, Harold W.; Ohrn, Theodore R.; Kneidel, Kurt E.; Rackers, Keith Gerard; Blake, James Erik; Nataraj, Shankar; van Doorn, Rene Hendrik Elias; Wilson, Merrill Anderson

    2007-02-20

    An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel. The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

  14. Ion transport membrane module and vessel system

    DOEpatents

    Stein, VanEric Edward; Carolan, Michael Francis; Chen, Christopher M.; Armstrong, Phillip Andrew; Wahle, Harold W.; Ohrn, Theodore R.; Kneidel, Kurt E.; Rackers, Keith Gerard; Blake, James Erik; Nataraj, Shankar; van Doorn, Rene Hendrik Elias; Wilson, Merrill Anderson

    2008-02-26

    An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel.The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

  15. Ion transport membrane module and vessel system

    DOEpatents

    Stein, VanEric Edward; Carolan, Michael Francis; Chen, Christopher M.; Armstrong, Phillip Andrew; Wahle, Harold W.; Ohrn, Theodore R.; Kneidel, Kurt E.; Rackers, Keith Gerard; Blake, James Erik; Nataraj, Shankar; Van Doorn, Rene Hendrik Elias; Wilson, Merrill Anderson

    2012-02-14

    An ion transport membrane system comprising (a) a pressure vessel having an interior, an exterior, an inlet, and an outlet; (b) a plurality of planar ion transport membrane modules disposed in the interior of the pressure vessel and arranged in series, each membrane module comprising mixed metal oxide ceramic material and having an interior region and an exterior region, wherein any inlet and any outlet of the pressure vessel are in flow communication with exterior regions of the membrane modules; and (c) one or more gas manifolds in flow communication with interior regions of the membrane modules and with the exterior of the pressure vessel. The ion transport membrane system may be utilized in a gas separation device to recover oxygen from an oxygen-containing gas or as an oxidation reactor to oxidize compounds in a feed gas stream by oxygen permeated through the mixed metal oxide ceramic material of the membrane modules.

  16. Intelligent Production Monitoring and Control based on Three Main Modules for Automated Manufacturing Cells in the Automotive Industry

    SciTech Connect

    Berger, Ulrich; Kretzschmann, Ralf; Algebra, A. Vargas Veronica

    2008-06-12

    The automotive industry is distinguished by regionalization and customization of products. As consequence, the diversity of products will increase while the lot sizes will decrease. Thus, more product types will be handled along the process chain and common production paradigms will fail. Although Rapid Manufacturing (RM) methodology will be used for producing small individual lot sizes, new solution for joining and assembling these components are needed. On the other hand, the non-availability of existing operational knowledge and the absence of dynamic and explicit knowledge retrieval minimize the achievement of on-demand capabilities. Thus, in this paper, an approach for an Intelligent Production System will be introduced. The concept is based on three interlinked main modules: a Technology Data Catalogue (TDC) based on an ontology system, an Automated Scheduling Processor (ASP) based on graph theory and a central Programmable Automation Controller (PAC) for real-time sensor/actor communication. The concept is being implemented in a laboratory set-up with several assembly and joining processes and will be experimentally validated in some research and development projects.

  17. Fifth parabolic dish solar thermal power program annual review: proceedings

    SciTech Connect

    1984-03-01

    The primary objective of the Review was to present the results of activities within the Parabolic Dish Technology and Module/Systems Development element of the Department of Energy's Solar Thermal Energy Systems Program. The Review consisted of nine technical sessions covering overall Project and Program aspects, Stirling and Brayton module development, concentrator and engine/receiver development, and associated hardware and test results to date; distributed systems operating experience; international dish development activities; and non-DOE-sponsored domestic dish activities. A panel discussion concerning business views of solar electric generation was held. These Proceedings contain the texts of presentations made at the Review, as submitted by their authors at the beginning of the Review; therefore, they may vary slightly from the actual presentations in the technical sessions.

  18. PSCAD Modules Representing PV Generator

    SciTech Connect

    Muljadi, E.; Singh, M.; Gevorgian, V.

    2013-08-01

    Photovoltaic power plants (PVPs) have been growing in size, and the installation time is very short. With the cost of photovoltaic (PV) panels dropping in recent years, it can be predicted that in the next 10 years the contribution of PVPs to the total number of renewable energy power plants will grow significantly. In this project, the National Renewable Energy Laboratory (NREL) developed a dynamic modeling of the modules to be used as building blocks to develop simulation models of single PV arrays, expanded to include Maximum Power Point Tracker (MPPT), expanded to include PV inverter, or expanded to cover an entire PVP. The focus of the investigation and complexity of the simulation determines the components that must be included in the simulation. The development of the PV inverter was covered in detail, including the control diagrams. Both the current-regulated voltage source inverter and the current-regulated current source inverter were developed in PSCAD. Various operations of the PV inverters were simulated under normal and abnormal conditions. Symmetrical and unsymmetrical faults were simulated, presented, and discussed. Both the three-phase analysis and the symmetrical component analysis were included to clarify the understanding of unsymmetrical faults. The dynamic model validation was based on the testing data provided by SCE. Testing was conducted at SCE with the focus on the grid interface behavior of the PV inverter under different faults and disturbances. The dynamic model validation covers both the symmetrical and unsymmetrical faults.

  19. Planar photovoltaic solar concentrator module

    DOEpatents

    Chiang, C.J.

    1992-12-01

    A planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor. 5 figs.

  20. Planar photovoltaic solar concentrator module

    DOEpatents

    Chiang, Clement J.

    1992-01-01

    A planar photovoltaic concentrator module for producing an electrical signal from incident solar radiation includes an electrically insulating housing having a front wall, an opposing back wall and a hollow interior. A solar cell having electrical terminals is positioned within the interior of the housing. A planar conductor is connected with a terminal of the solar cell of the same polarity. A lens forming the front wall of the housing is operable to direct solar radiation incident to the lens into the interior of the housing. A refractive optical element in contact with the solar cell and facing the lens receives the solar radiation directed into the interior of the housing by the lens and directs the solar radiation to the solar cell to cause the solar cell to generate an electrical signal. An electrically conductive planar member is positioned in the housing to rest on the housing back wall in supporting relation with the solar cell terminal of opposite polarity. The planar member is operable to dissipate heat radiated by the solar cell as the solar cell generates an electrical signal and further forms a solar cell conductor connected with the solar cell terminal to permit the electrical signal generated by the solar cell to be measured between the planar member and the conductor.

  1. LLE review

    SciTech Connect

    Keck, R.L.

    1991-01-01

    This volume of the LLE Review, covering the period October-December 1991, contains articles on the analysis of argon-filled target experiments, and a theoretical analysis of the impact of nonlocal heat transport in laser filamentation in plasmas. In the Advanced Technology section there is an article on mechanisms that affect thin-film conductivity, and a report on the gain characteristics of the 20-cm SSA prototype amplifier to be used in the OMEGA Upgrade. Finally, the activities of the National Laser Users Facility and the GDL and OMEGA laser facilities are summarized. Highlights of the research reported in this issue are: argon radiation from argon-filled, polymer-shell targets is used as a core-temperature diagnostic and density diagnostic of the surrounding region in a regime where the argon line radiation is strongly absorbed. A theoretical analysis of the impact of nonlocal heat transport on laser filamentation in plasmas is developed. The resulting model is compared with experimental observations and the implications for ICF are discussed. A study of thermal conductivity in thin films seeks to identify mechanisms that result in degradation of thin-film conductivity. Identifying these mechanisms can lead to changes in the thin-film manufacture that will improve their resistance to laser damage.

  2. Science Requirements Reviews

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Science Requirements Reviews Network Requirements Reviews Requirements Review Reports Case Studies News & Publications ESnet News Publications and Presentations Galleries ESnet Awards and Honors Blog ESnet Live Home » Science Engagement » Science Requirements Reviews Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1

  3. Network Requirements Reviews

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reviews Science Engagement Move your data Programs & Workshops Science Requirements Reviews Network Requirements Reviews Documents and Background Materials FAQ for Case Study Authors BER Requirements Review 2015 ASCR Requirements Review 2015 Previous Reviews Requirements Review Reports Case Studies Contact Us Technical Assistance: 1 800-33-ESnet (Inside US) 1 800-333-7638 (Inside US) 1 510-486-7600 (Globally) 1 510-486-7607 (Globally) Report Network Problems: trouble@es.net Provide Web Site

  4. EXPERIENCES ON PID TESTING OF PV MODULES IN 2012 | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    EXPERIENCES ON PID TESTING OF PV MODULES IN 2012 EXPERIENCES ON PID TESTING OF PV MODULES IN 2012 Presented at the PV Module Reliability Workshop, February 26 - 27 2013, Golden, ...

  5. Flat-Plate Photovoltaic Module Basics | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Module Basics Flat-Plate Photovoltaic Module Basics August 20, 2013 - 4:25pm Addthis ... a high transmission in the wavelengths that can be used by the solar cells in the module. ...

  6. Ensuring Quality of PV Modules: Preprint

    SciTech Connect

    Kurtz, S.; Wohlgemuth, J.; Hacke, P.; Kempe, M.; Sample, T.; Yamamichi, M.; Kondo, M.; Doi, T.; Otani, K.; Amano, J.

    2011-07-01

    Photovoltaic (PV) customers need to have confidence in the PV modules they purchase. Currently, no test can quantify a module's lifetime with confidence, but stress tests are routinely used to differentiate PV product designs. We suggest that the industry would be strengthened by using the wisdom of the community to develop a single set of tests that will help customers quantify confidence in PV products. This paper evaluates the need for quality assurance (QA) standards and suggests a path for creating these. Two types of standards are needed: 1) QA of the module design and 2) QA of the manufacturing process.

  7. Skew chicane based betatron eigenmode exchange module

    DOEpatents

    Douglas, David

    2010-12-28

    A skewed chicane eigenmode exchange module (SCEEM) that combines in a single beamline segment the separate functionalities of a skew quad eigenmode exchange module and a magnetic chicane. This module allows the exchange of independent betatron eigenmodes, alters electron beam orbit geometry, and provides longitudinal parameter control with dispersion management in a single beamline segment with stable betatron behavior. It thus reduces the spatial requirements for multiple beam dynamic functions, reduces required component counts and thus reduces costs, and allows the use of more compact accelerator configurations than prior art design methods.

  8. Microscale autonomous sensor and communications module

    DOEpatents

    Okandan, Murat; Nielson, Gregory N

    2014-03-25

    Various technologies pertaining to a microscale autonomous sensor and communications module are described herein. Such a module includes a sensor that generates a sensor signal that is indicative of an environmental parameter. An integrated circuit receives the sensor signal and generates an output signal based at least in part upon the sensor signal. An optical emitter receives the output signal and generates an optical signal as a function of the output signal. An energy storage device is configured to provide power to at least the integrated circuit and the optical emitter, and wherein the module has a relatively small diameter and thickness.

  9. Stacked vapor fed amtec modules

    DOEpatents

    Sievers, Robert K.

    1989-01-01

    The present invention pertains to a stacked AMTEC module. The invention includes a tubular member which has an interior. The member is comprised of a ion conductor that substantially conducts ions relative to electrons, preferably a beta"-alumina solid electrolyte, positioned about the interior. A porous electrode for conducting electrons and allowing sodium ions to pass therethrough, and wherein electrons and sodium ions recombine to form sodium is positioned about the beta"-alumina solid electrolyte. The electrode is operated at a temperature and a pressure that allows the recombined sodium to vaporize. Additionally, an outer current collector grid for distributing electrons throughout the porous electrode is positioned about and contacts the porous electrode. Also included in the invention is transporting means for transporting liquid sodium to the beta"-alumina solid electrolyte of the tubular member. A transition piece is positioned about the interior of the member and contacts the transporting means. The transition piece divides the member into a first cell and a second cell such that each first and second cell has a beta"-alumina solid electrolyte, a first and second porous electrode and a grid. The transition piece conducts electrons from the interior of the tubular member. There is supply means for supplying sodium to the transporting means. Preferably the supply means is a shell which surrounds the tubular member and is operated at a temperature such that the vaporized sodium condenses thereon. Returning means for returning the condensed sodium from the shell to the transporting means provides a continuous supply of liquid sodium to the transporting means. Also, there are first conducting means for conducting electric current from the transition piece which extends through the shell, and second conducting means for conducting electric current to the grid of the first cell which extends through the shell.

  10. PROJECT PROFILE: Advanced Thermal Management for Higher Module Power Output

    Energy.gov [DOE]

    Higher temperatures of photovoltaic (PV) modules are causing lower than projected module performance. For example, a free-standing Si PV module has 0.4% decrease in efficiency per degree Celsius. Reducing the module temperature to near ambient levels will increase yearly energy output by 8%. This project will enable lower operating temperatures for modules, resulting in higher module power output and lower levelized cost of electricity (LCOE).

  11. Module: Emission Factors for Deforestation | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    www.leafasia.orgtoolstechnical-guidance-series-emission-factors-defo Cost: Free Language: English Module: Emission Factors for Deforestation Screenshot Logo: Module: Emission...

  12. DOE Technical Standards Policy & Procedures (TSPP) Tutorial Modules...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Technical Standards Policy & Procedures (TSPP) Tutorial Modules Available DOE Technical Standards Policy & Procedures (TSPP) Tutorial Modules Available April 7, 2016 - 2:48pm ...

  13. General Renewable Energy Technology Module | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Technology Module Jump to: navigation, search Tool Summary LAUNCH TOOL Name: General Renewable Energy Technology Module AgencyCompany Organization: World Bank Sector: Energy...

  14. APT Target-Blanket Module - Fabrication and Characterization...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: APT Target-Blanket Module - Fabrication and Characterization of Prototypical Assemblies Citation Details In-Document Search Title: APT Target-Blanket Module - ...

  15. Nanoscale Periodic Modulations on Sodium Chloride Induced by...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: Nanoscale Periodic Modulations on Sodium Chloride Induced by Surface Charges Citation Details In-Document Search Title: Nanoscale Periodic Modulations on Sodium ...

  16. Table 4. Average value of photovoltaic modules, 2005-2015

    Energy Information Administration (EIA) (indexed site)

    Average value of photovoltaic modules, 2005-2015" "(dollars per peak watt)" ... Administration, Form EIA-63B, 'Annual Photovoltaic CellModule Shipments Report.' Note: ...

  17. PROJECT PROFILE: Advanced Thermal Management for Higher Module...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    National Renewable Energy Laboratory, Golden, CO Amount Awarded: 2,816,911 Higher temperatures of photovoltaic (PV) modules are causing lower than projected module performance. ...

  18. Generation of Coherent X-Ray Radiation through Modulation Compression...

    Office of Scientific and Technical Information (OSTI)

    Generation of Coherent X-Ray Radiation through Modulation Compression Citation Details In-Document Search Title: Generation of Coherent X-Ray Radiation through Modulation Compression ...

  19. Tailored Terahertz Pulses from a Laser-Modulated Electron Beam

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Researchers at the ... terahertz radiation from a relativistic electron beam modulated by a femtosecond laser. ...

  20. NREL: Performance and Reliability R&D - PV Module Reliability...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    PV Module Reliability Workshop NREL hosts an annual Photovoltaic Module Reliability Workshop (PVMRW) so that solar technology experts can share information leading to the ...

  1. High Efficiency Low-Cost Perovskite Solar Cell Modules

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    High Efficiency, Low-Cost Perovskite Solar Cell Modules High Efficiency, Low-Cost Perovskite Solar Cell Modules Perovskite solar cells have the ability to greatly increase the ...

  2. Partial Shade Stress Test for Thin-Film Photovoltaic Modules...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Partial Shade Stress Test for Thin-Film Photovoltaic Modules Preprint Timothy J. ... Partial shade stress test for thin-film photovoltaic modules Timothy J Silverman , ...

  3. V-043: Perl Locale::Maketext Module '_compile()' Multiple Code...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    V-043: Perl Locale::Maketext Module 'compile()' Multiple Code Injection Vulnerabilities ... Arbitrary Code and View Arbitrary Files V-002: EMC NetWorker Module for Microsoft ...

  4. Linkage to Previous International PV Module QA Task Force Workshops...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Linkage to Previous International PV Module QA Task Force Workshops: Proposal for Rating System Linkage to Previous International PV Module QA Task Force Workshops: Proposal for ...

  5. Energy Efficiency at Home - An Interdisciplinary Module for Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    at Home - An Interdisciplinary Module for Energy Education Energy Efficiency at Home - An Interdisciplinary Module for Energy Education Below is information about the student ...

  6. Module: Activity Data for Deforestation | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Website: www.leafasia.orgtoolstechnical-guidance-series-activity-data-defores Cost: Free Language: English Module: Activity Data for Deforestation Screenshot Logo: Module:...

  7. Statistical and Domain Analytics Applied to PV Module Lifetime...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Statistical and Domain Analytics Applied to PV Module Lifetime and Degradation Science Statistical and Domain Analytics Applied to PV Module Lifetime and Degradation Science ...

  8. Scannerless laser range imaging using loss modulation

    DOEpatents

    Sandusky, John V.

    2011-08-09

    A scannerless 3-D imaging apparatus is disclosed which utilizes an amplitude modulated cw light source to illuminate a field of view containing a target of interest. Backscattered light from the target is passed through one or more loss modulators which are modulated at the same frequency as the light source, but with a phase delay .delta. which can be fixed or variable. The backscattered light is demodulated by the loss modulator and detected with a CCD, CMOS or focal plane array (FPA) detector to construct a 3-D image of the target. The scannerless 3-D imaging apparatus, which can operate in the eye-safe wavelength region 1.4-1.7 .mu.m and which can be constructed as a flash LADAR, has applications for vehicle collision avoidance, autonomous rendezvous and docking, robotic vision, industrial inspection and measurement, 3-D cameras, and facial recognition.

  9. Photovoltaic module with removable wind deflector

    DOEpatents

    Botkin, Jonathan; Graves, Simon; Danning, Matt; Culligan, Matthew

    2013-05-28

    A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

  10. Photovoltaic module with removable wind deflector

    DOEpatents

    Botkin, Jonathan; Graves, Simon; Danning, Matt; Culligan, Matthew

    2012-08-07

    A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

  11. Model Documentation Report: Macroeconomic Activity Module (MAM...

    Energy Information Administration (EIA) (indexed site)

    Activity Module (MAM) of the National Energy Modeling System May 2014 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 U.S. Energy ...

  12. Photovoltaic module with removable wind deflector

    DOEpatents

    Botkin, Jonathan; Graves, Simon; Danning, Matt; Culligan, Matthew

    2014-02-18

    A photovoltaic (PV) module assembly including a PV module, a deflector, and a clip. The PV module includes a PV device and a frame. A PV laminate is assembled to the frame, and the frame includes a support arm forming a seat. The deflector defines a front face and a rear face, with the clip extending from either the trailing frame member or the rear face of the deflector. In a mounted state, the deflector is nested within the seat and is releasably mounted to the trailing frame member via the clip. In some embodiments, the support arm forms a second seat, with the PV module assembly providing a second mounted state in which the deflector is in a differing orientation/slope, nested within the second seat and releasably mounted to the trailing frame member via the clip.

  13. PV Module Reliability Research (Fact Sheet)

    SciTech Connect

    Not Available

    2013-06-01

    This National Center for Photovoltaics sheet describes the capabilities of its PV module reliability research. The scope and core competencies and capabilities are discussed and recent publications are listed.

  14. WRAP Module 1 sampling and analysis plan

    SciTech Connect

    Mayancsik, B.A.

    1995-03-24

    This document provides the methodology to sample, screen, and analyze waste generated, processed, or otherwise the responsibility of the Waste Receiving and Processing Module 1 facility. This includes Low-Level Waste, Transuranic Waste, Mixed Waste, and Dangerous Waste.

  15. DETECTOR FOR MODULATED AND UNMODULATED SIGNALS

    DOEpatents

    Patterson, H.H.; Webber, G.H.

    1959-08-25

    An r-f signal-detecting device is described, which is embodied in a compact coaxial circuit principally comprising a detecting crystal diode and a modulating crystal diode connected in parallel. Incoming modulated r-f signals are demodulated by the detecting crystal diode to furnish an audio input to an audio amplifier. The detecting diode will not, however, produce an audio signal from an unmodulated r-f signal. In order that unmodulated signals may be detected, such incoming signals have a locally produced audio signal superimposed on them at the modulating crystal diode and then the"induced or artificially modulated" signal is reflected toward the detecting diode which in the process of demodulation produces an audio signal for the audio amplifier.

  16. Optimal design of reverse osmosis module networks

    SciTech Connect

    Maskan, F.; Wiley, D.E.; Johnston, L.P.M.; Clements, D.J.

    2000-05-01

    The structure of individual reverse osmosis modules, the configuration of the module network, and the operating conditions were optimized for seawater and brackish water desalination. The system model included simple mathematical equations to predict the performance of the reverse osmosis modules. The optimization problem was formulated as a constrained multivariable nonlinear optimization. The objective function was the annual profit for the system, consisting of the profit obtained from the permeate, capital cost for the process units, and operating costs associated with energy consumption and maintenance. Optimization of several dual-stage reverse osmosis systems were investigated and compared. It was found that optimal network designs are the ones that produce the most permeate. It may be possible to achieve economic improvements by refining current membrane module designs and their operating pressures.

  17. Rack assembly for mounting solar modules

    DOEpatents

    Plaisted, Joshua Reed; West, Brian

    2014-06-10

    A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

  18. Rack assembly for mounting solar modules

    DOEpatents

    Plaisted, Joshua Reed; West, Brian

    2012-09-04

    A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures to be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

  19. Rack assembly for mounting solar modules

    DOEpatents

    Plaisted, Joshua Reed; West, Brian

    2010-12-28

    A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

  20. Review comments from 2004 ATD Annual Review

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Report on the Annual Review of the FY 2005 Advanced Technology Development Program [pic] August 9 & 10, 2005 Argonne IL November 2005 U.S. Department of Energy Office of FreedomCAR and Vehicle Technologies High Power Energy Storage Program November 3, 2005 Dear Colleague: This document is a summary of the evaluation and comments provided by the review panel for the FY 2005 Department of Energy (DOE) Advanced Technology Development (ATD) program annual review. The review was held at the

  1. NEMS Freight Transportation Module Improvement Study

    Energy Information Administration (EIA) (indexed site)

    NEMS Freight Transportation Module Improvement Study February 2015 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 U.S. Energy Information Administration | NEMS Freight Transportation Module Improvement Study i This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other

  2. Ultralight photovoltaic modules for unmanned aerial vehicles

    SciTech Connect

    Nowlan, M.J.; Maglitta, J.C.; Darkazalli, G.; Lamp, T.

    1997-12-31

    New lightweight photovoltaic modules are being developed for powering high altitude unmanned aerial vehicles (UAVs). Modified low-cost terrestrial solar cell and module technologies are being applied to minimize vehicle cost. New processes were developed for assembling thin solar cells, encapsulant films, and cover films. An innovative by-pass diode mounting approach that uses a solar cell as a heat spreader was devised and tested. Materials and processes will be evaluated through accelerated environmental testing.

  3. Process of making solar cell module

    DOEpatents

    Packer, M.; Coyle, P.J.

    1981-03-09

    A process is presented for the manufacture of solar cell modules. A solution comprising a highly plasticized polyvinyl butyral is applied to a solar cell array. The coated array is dried and sandwiched between at last two sheets of polyvinyl butyral and at least two sheets of a rigid transparent member. The sandwich is laminated by the application of heat and pressure to cause fusion and bonding of the solar cell array with the rigid transparent members to produce a solar cell module.

  4. WUFI Basement Module | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    WUFI Basement Module WUFI Basement Module WUFI is a menu-driven PC program which allows realistic calculation of the transient coupled one-dimensional heat and moisture transport in multi-layer building components exposed to natural weather. Click the image to see an animated version of the software. WUFI is a menu-driven PC program which allows realistic calculation of the transient coupled one-dimensional heat and moisture transport in multi-layer building components exposed to natural

  5. Hydrogen production in the K-Basin ion exchange columns, modules and cartridge filters

    SciTech Connect

    Not Available

    1994-12-21

    K-Basin uses ion exchange modules and ion exchange (IX) columns for removing radionuclides from the basin water. When the columns and modules are loaded, they are removed from service, drained and stored. After a few IX columns accumulate in storage, they are moved to a burial box. One of the burial box contains 33 columns and the other, six. The radionuclides act on the liquid left within and adhering to the beads to produce hydrogen. This report describes the generation rate, accumulation rate and significance of that accumulation. This summary also highlights those major areas of concern to the external (to Westinghouse Hanford Company [WHC]) reviewers. Appendix H presents the comments made by the external reviewers and, on a separate sheet, the responses to those comments. The concerns regarding the details of the analytical approach, are addressed in Appendix H and in the appropriate section.

  6. Photovoltaic module certification/laboratory accreditation criteria development: Implementation handbook

    SciTech Connect

    Osterwald, C.R.; Hammond, R.L.; Wood, B.D.; Backus, C.E.; Sears, R.L.; Zerlaut, G.A.; D`Aiello, R.V.

    1996-08-01

    This document covers the second phase of a two-part program. Phase I provided an overview of the structure and function of typical product certification/laboratory accreditation programs. This report (Phase H) provides most of the draft documents that will be necessary for the implementation of a photovoltaic (PV) module certification/laboratory accreditation program. These include organizational documents such as articles of incorporation, bylaws, and rules of procedure, as well as marketing and educational program documents. In Phase I, a 30-member criteria development committee was established to guide, review and reach a majority consensus regarding criteria for a PV certification/laboratory accreditation program. Committee members represented PV manufacturers, end users, standards and codes organizations, and testing laboratories. A similar committee was established for Phase II; the criteria implementation committee consisted of 29 members. Twenty-one of the Phase I committee members also served on the Phase II committee, which helped to provide program continuity during Phase II.

  7. Design specifications for manufacturability of MCM-C multichip modules

    SciTech Connect

    Blazek, R.; Desch, J.; Kautz, D.; Morgenstern, H.

    1996-10-01

    A comprehensive guide for ceramic-based multichip modules (MCMS) has been developed by AlliedSignal Federal Manufacturing & Technologies (FM&T) to provide manufacturability information for its customers about how MCM designs can be affected by existing process and equipment capabilities. This guide extends beyond a listing of design rules by providing information about design layout, low- temperature cofired ceramic (LTCC) substrate fabrication, MCM assembly and electrical testing Electrical mechanical packaging, environmental, and producibility issues are reviewed. Examples of three MCM designs are shown in the form of packaging cross-sectional views, LTCC substrate layer allocations, and overall MCM photographs. The guide has proven to be an effective tool for enhancing communications between MCM designers and manufacturers and producing a microcircuit that meets design requirements within the limitations of process capabilities.

  8. Nuclear modules of ITER tokamak systems code

    SciTech Connect

    Gohar, Y.; Baker, C.; Brooks, J.; Finn, P.; Hassanein, A.; Willms, S.; Barr, W.; Bushigin, A.; Kalyanam, K.M.; Haines, J.

    1987-10-01

    Nuclear modules were developed to model various reactor components in the ITER systems code. Several design options and cost algorithms are included for each component. The first wall, blanket and shield modules calculate the beryllium zone thickness, the disruptions results, the nuclear responses in different components including the toroidal field coils. Tungsten shield/water coolant/steel structure and steel shield/water coolant are the shield options for the inboard and outboard sections of the reactor. Lithium nitrate dissolved in the water coolant with a variable beryllium zone thickness in the outboard section of the reactor provides the tritium breeding capability. The reactor vault module defines the thickness of the reactor wall and the roof based on the dose equivalent during operation including skyshine contribution. The impurity control module provides the design parameters for the divertor including plate design, heat load, erosion rate, tritium permeation through the plate material to the coolant, plasma contamination by sputtered impurities, and plate lifetime. Several materials: Be, C, V, Mo, and W can be used for the divertor plate to cover a range of plasma edge temperatures. The tritium module calculates tritium and deuterium flow rates for the reactor plant. The tritium inventory in the fuelers, neutral beams, vacuum pumps, impurity control, first wall, and blanket is calculated. Tritium requirements are provided for different operating conditions. The nuclear models are summarized in this paper including the different design options and key analyses of each module. 39 refs., 3 tabs.

  9. Cell shunt resistance and photovoltaic module performance

    SciTech Connect

    McMahon, T.J.; Basso, T.S.; Rummel, S.R.

    1996-05-01

    Shunt resistance of cells in photovoltaic modules can affect module power output and could indicate flawed manufacturing processes and reliability problems. The authors describe a two-terminal diagnostic method to directly measure the shunt resistance of individual cells in a series-connected module non-intrusively, without deencapsulation. Peak power efficiency vs. light intensity was measured on a 12-cell, series-connected, single crystalline module having relatively high cell shunt resistances. The module was remeasured with 0.5-, 1-, and 2-ohm resistors attached across each cell to simulate shunt resistances of several emerging technologies. Peak power efficiencies decreased dramatically at lower light levels. Using the PSpice circuit simulator, the authors verified that cell shunt and series resistances can indeed be responsible for the observed peak power efficiency vs. intensity behavior. The authors discuss the effect of basic cell diode parameters, i.e., shunt resistance, series resistance, and recombination losses, on PV module performance as a function of light intensity.

  10. 2013 Annual Merit Review Results Report - Merit Review Attendees...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Merit Review Attendees 2013 Annual Merit Review Results Report - Merit Review Attendees Merit review of DOE Vehicle Technologies research activities 2013amr13.pdf (654.24 KB) ...

  11. 2014 Annual Merit Review Results Report - Merit Review Attendees...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Merit Review Attendees 2014 Annual Merit Review Results Report - Merit Review Attendees Merit review of DOE Vehicle Technologies research activities 2014amr13.pdf (833.06 KB) ...

  12. Program Evaluation and Review Technique Operational Review Meeting...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Program Evaluation and Review Technique Operational Review Meeting 2016 Program Evaluation and Review Technique Operational Review Meeting 2016 February 23, 2016 9:00AM PST to...

  13. Post-Review Feedback Questionnaire for Evaluating the Peer Review...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Post-Review Feedback Questionnaire for Evaluating the Peer Review Process Post-Review Feedback Questionnaire for Evaluating the Peer Review Process EERE is committed to continuous ...

  14. Review of Test Results

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    4 Revision 1 Effective June 2008 Review of Test Results Prepared by Electric ... 7 Appendices Appendix A, Test Results Review and Approval Form ...

  15. Standard Review Plan Overview

    Office of Environmental Management (EM)

    and successfully by the Nuclear Regulatory Commission (NRC) for evaluating U.S. ... and Field reviews, existing project review guides and protocols, and consensus standards. ...

  16. HPC Requirements Reviews

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reviews: Target 2017 Requirements Reviews: Target 2014 Overview Published Reports Case Study FAQs NERSC HPC Achievement Awards Accelerator Science Astrophysics & Cosmology...

  17. NGNP PHASE I REVIEW

    Energy.gov [DOE] (indexed site)

    NGNP PHASE I REVIEW NEAC REACTOR TECHNOLOGY SUBCOMMITTEE CURRENT STATUS DECEMBER 9, 2010 EPACT 2005 REQUIREMENTS * FIRST PROJECT PHASE REVIEW-On a determination by the Secretary...

  18. ORISE: Peer Review Management

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Management Man participating in a peer review The Oak Ridge Institute for Science and Education (ORISE) ensures that scientific reviews are conducted in a professional manner and...

  19. Readiness Review Training- Member

    Energy.gov [DOE]

    Slides used for November 10, 2010 Readiness Review Member Training at the Idaho National Laboratory. Course provides tools and tips to be an effective readiness review team member.

  20. Modular integrated video system (MIVS) review station

    SciTech Connect

    Garcia, M.L.

    1988-01-01

    An unattended video surveillance unit, the Modular Integrated Video System (MIVS), has been developed by Sandia National Laboratories for International Safeguards use. An important support element of this system is a semi-automatic Review Station. Four component modules, including an 8 mm video tape recorder, a 4-inch video monitor, a power supply and control electronics utilizing a liquid crystal display (LCD) are mounted in a suitcase for probability. The unit communicates through the interactive, menu-driven LCD and may be operated on facility power through the world. During surveillance, the MIVS records video information at specified time intervals, while also inserting consecutive scene numbers and tamper event information. Using either of two available modes of operation, the Review Station reads the inserted information and counts the number of missed scenes and/or tamper events encountered on the tapes, and reports this to the user on the LCD. At the end of a review session, the system will summarize the results of the review, stop the recorder, and advise the user of the completion of the review. In addition, the Review Station will check for any video loss on the tape.

  1. WBG Gate Drivers for Power Modules

    Energy.gov [DOE]

    2013 DOE Hydrogen and Fuel Cells Program and Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting

  2. DOE special projects: PLACE3S GIS MODULE [Final report

    SciTech Connect

    2002-07-31

    PLACE3S (PLAnning for Community Energy, Economic and Environmental Sustainability) energy option matching module.

  3. Module 2 - Work Breakdown Structure | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    2 - Work Breakdown Structure Module 2 - Work Breakdown Structure This module focuses on the Work Breakdown Structure (WBS) and other planning elements. This module defines and illustrates the Work Breakdown Structure (WBS), WBS dictionary, Organizational Breakdown Structure (OBS) and Responsibility Assignment Matrix (RAM). Begin Module >> (554.25

  4. Module 5 - EVMS Concepts and Methods | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    5 - EVMS Concepts and Methods Module 5 - EVMS Concepts and Methods This module focuses on Earned Value concepts and methods. This module outlines the criteria needed for implementing Earned Value management, the basic Earned Value terminology, and the different methods used to calculate Earned Value. Begin Module >> (741.8

  5. Single, stretched membrane, structural module experiments

    SciTech Connect

    Wood, R.L.

    1986-02-01

    This report describes tests done on stretched-membrane heliostats used to reflect solar radiation onto a central receiver. The tests were used to validate prior analysis and mathematical models developed to describe module performance. The modules tested were three meters in diameter and had reflective polymer film laminated to the membrane. The frames were supported at three points equally spaced around the ring. Three modules were pneumatically attached with their weight suspended at the bottom support, two were pneumatically attached with their weight suspended from the upper mounts, and one was rigidly attached with its weight suspended at the bottom mount. By varying the membrane tension we could simulate a uniform wind loading normal to the mirror's surface. A video camera 15+ meters away from the mirror recorded the virtual image of a target grid as reflected by the mirrors' surface. The image was digitized and stored on a microcomputer. Using the law of reflection and analytic geometry, we computed the surface slopes of a sampling of points on the surface. The dominant module response was consistent with prior SERI analyses. The simple analytical model is quite adequate for designing and sizing single-membrane modules if the initial imperfections and their amplification are appropriately controlled. To avoid potential problems resulting from the fundamentally n = 2 deformation phenomena, we advise using either relatively stiffer ring frames or more than three support points.

  6. Three dimensional, multi-chip module

    DOEpatents

    Bernhardt, Anthony F.; Petersen, Robert W.

    1993-01-01

    A plurality of multi-chip modules are stacked and bonded around the perimeter by sold-bump bonds to adjacent modules on, for instance, three sides of the perimeter. The fourth side can be used for coolant distribution, for more interconnect structures, or other features, depending on particular design considerations of the chip set. The multi-chip modules comprise a circuit board, having a planarized interconnect structure formed on a first major surface, and integrated circuit chips bonded to the planarized interconnect surface. Around the periphery of each circuit board, long, narrow "dummy chips" are bonded to the finished circuit board to form a perimeter wall. The wall is higher than any of the chips on the circuit board, so that the flat back surface of the board above will only touch the perimeter wall. Module-to-module interconnect is laser-patterned o the sides of the boards and over the perimeter wall in the same way and at the same time that chip to board interconnect may be laser-patterned.

  7. Three dimensional, multi-chip module

    DOEpatents

    Bernhardt, A.F.; Petersen, R.W.

    1993-08-31

    A plurality of multi-chip modules are stacked and bonded around the perimeter by sold-bump bonds to adjacent modules on, for instance, three sides of the perimeter. The fourth side can be used for coolant distribution, for more interconnect structures, or other features, depending on particular design considerations of the chip set. The multi-chip modules comprise a circuit board, having a planarized interconnect structure formed on a first major surface, and integrated circuit chips bonded to the planarized interconnect surface. Around the periphery of each circuit board, long, narrow dummy chips'' are bonded to the finished circuit board to form a perimeter wall. The wall is higher than any of the chips on the circuit board, so that the flat back surface of the board above will only touch the perimeter wall. Module-to-module interconnect is laser-patterned on the sides of the boards and over the perimeter wall in the same way and at the same time that chip to board interconnect may be laser-patterned.

  8. Diesel Emission Control Review

    Energy.gov [DOE]

    Reviews regulatory requirements and technology approaches for diesel emission control for heavy and light duty applications

  9. Vehicle Emissions Review- 2012

    Energy.gov [DOE]

    Reviews vehicle emission control highlighting representative studies that illustrate the state-of-the-art

  10. Full Reviews: Reservoir Characterization

    Energy.gov [DOE]

    Below are the project presentations and respective peer reviewer comments for Reservoir Characterization.

  11. Plasmon absorption modulator systems and methods

    DOEpatents

    Kekatpure, Rohan Deodatta; Davids, Paul

    2014-07-15

    Plasmon absorption modulator systems and methods are disclosed. A plasmon absorption modulator system includes a semiconductor substrate, a plurality of quantum well layers stacked on a top surface of the semiconductor substrate, and a metal layer formed on a top surface of the stack of quantum well layers. A method for modulating plasmonic current includes enabling propagation of the plasmonic current along a metal layer, and applying a voltage across the stack of quantum well layers to cause absorption of a portion of energy of the plasmonic current by the stack of quantum well layers. A metamaterial switching system includes a semiconductor substrate, a plurality of quantum well layers stacked on a top surface of the semiconductor substrate, and at least one metamaterial structure formed on a top surface of the stack of quantum well layers.

  12. Siemens SOFC Test Article and Module Design

    SciTech Connect

    2011-03-31

    Preliminary design studies of the 95 kWe-class SOFC test article continue resulting in a stack architecture of that is 1/3 of 250 kWe-class SOFC advanced module. The 95 kWeclass test article is envisioned to house 20 bundles (eight cells per bundle) of Delta8 cells with an active length of 100 cm. Significant progress was made in the conceptual design of the internal recirculation loop. Flow analyses were initiated in order to optimize the bundle row length for the 250 kWeclass advanced module. A preferred stack configuration based on acceptable flow and thermal distributions was identified. Potential module design and analysis issues associated with pressurized operation were identified.

  13. Low thermal resistance power module assembly

    DOEpatents

    Hassani, Vahab; Vlahinos, Andreas; Bharathan, Desikan

    2007-03-13

    A power module assembly with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate with passageways or openings for coolant that extend through the plate from a lower surface to an upper surface. A circuit substrate is provided and positioned on the spreader plate to cover the coolant passageways. The circuit substrate includes a bonding layer configured to extend about the periphery of each of the coolant passageways and is made up of a substantially nonporous material. The bonding layer may be solder material which bonds to the upper surface of the plate to provide a continuous seal around the upper edge of each opening in the plate. The assembly includes power modules mounted on the circuit substrate on a surface opposite the bonding layer. The power modules are positioned over or proximal to the coolant passageways.

  14. ILC Marx Modulator Development Program Status

    SciTech Connect

    Burkhart, C.; Beukers, T.; Larsen, R.; Macken, K.; Nguyen, M.; Olsen, J.; Tang, T.; /SLAC

    2009-03-04

    Development of a first generation prototype (P1) Marx-topology klystron modulator for the International Linear Collider is nearing completion at the Stanford Linear Accelerator Center. It is envisioned as a smaller, lower cost, and higher reliability alternative to the present, bouncer-topology, 'Baseline Conceptual Design'. The Marx presents several advantages over conventional klystron modulator designs. It is physically smaller; there is no pulse transformer (quite massive at ILC parameters) and the energy storage capacitor bank is quite small, owing to the active droop compensation. It is oil-free; voltage hold-off is achieved using air insulation. It is air cooled; the secondary air-water heat exchanger is physically isolated from the electronic components. The P1-Marx employs all solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. A general overview of the modulator design and the program status are presented.

  15. Development of Fuel Shuffling Module for PHISICS

    SciTech Connect

    Allan Mabe; Andrea Alfonsi; Cristian Rabiti; Aaron Epiney; Michael Lineberry

    2013-06-01

    PHISICS (Parallel and Highly Innovative Simulation for the INL Code System) [4] code toolkit has been in development at the Idaho National Laboratory. This package is intended to provide a modern analysis tool for reactor physics investigation. It is designed with the mindset to maximize accuracy for a given availability of computational resources and to give state of the art tools to the modern nuclear engineer. This is obtained by implementing several different algorithms and meshing approaches among which the user will be able to choose, in order to optimize his computational resources and accuracy needs. The software is completely modular in order to simplify the independent development of modules by different teams and future maintenance. The package is coupled with the thermo-hydraulic code RELAP5-3D [3]. In the following the structure of the different PHISICS modules is briefly recalled, focusing on the new shuffling module (SHUFFLE), object of this paper.

  16. Scannerless loss modulated flash color range imaging

    DOEpatents

    Sandusky, John V.; Pitts, Todd Alan

    2009-02-24

    Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

  17. Scannerless loss modulated flash color range imaging

    DOEpatents

    Sandusky, John V.; Pitts, Todd Alan

    2008-09-02

    Scannerless loss modulated flash color range imaging methods and apparatus are disclosed for producing three dimensional (3D) images of a target within a scene. Apparatus and methods according to the present invention comprise a light source providing at least three wavelengths (passbands) of illumination that are each loss modulated, phase delayed and simultaneously directed to illuminate the target. Phase delayed light backscattered from the target is spectrally filtered, demodulated and imaged by a planar detector array. Images of the intensity distributions for the selected wavelengths are obtained under modulated and unmodulated (dc) illumination of the target, and the information contained in the images combined to produce a 3D image of the target.

  18. Module level solutions to solar cell polarization

    DOEpatents

    Xavier, Grace , Li; Bo

    2012-05-29

    A solar cell module includes interconnected solar cells, a transparent cover over the front sides of the solar cells, and a backsheet on the backsides of the solar cells. The solar cell module includes an electrical insulator between the transparent cover and the front sides of the solar cells. An encapsulant protectively packages the solar cells. To prevent polarization, the insulator has resistance suitable to prevent charge from leaking from the front sides of the solar cells to other portions of the solar cell module by way of the transparent cover. The insulator may be attached (e.g., by coating) directly on an underside of the transparent cover or be a separate layer formed between layers of the encapsulant. The solar cells may be back junction solar cells.

  19. Soliton dynamics in modulated Bessel photonic lattices

    SciTech Connect

    Ruelas, Adrian; Lopez-Aguayo, Servando; Gutierrez-Vega, Julio C.

    2010-12-15

    We address the existence and the controlled stability of two-dimensional solitons in modulated Bessel lattices (MBL) induced by a superposition of nondiffracting Bessel beams. We show that variation of the modulation parameter of the lattice and the initial transverse momentum of the soliton significantly modify the behavior of the solitons. We find that, under suitable and well-identified conditions, solitons propagating in the MBL exhibit six regimes of transverse mobility: stationary, oscillatory, rotating, unbounded or escape, transitional, and unstable. These results report propagating solitons that can develop these dynamics of transverse motion.

  20. Ponderomotive Forces On Waves In Modulated Media

    SciTech Connect

    Dodin, I.Y; Fisch, Nathaniel

    2014-02-28

    Nonlinear interactions of waves via instantaneous cross-phase modulation can be cast in the same way as ponderomotive wave-particle interactions in high-frequency electromagnetic fi eld. The ponderomotive effect arises when rays of a probe wave scatter off perturbations of the underlying medium produced by a second, modulation wave, much like charged particles scatter off a quasiperiodic field. Parallels with the point-particle dynamics, which itself is generalized by this theory, lead to new methods of wave manipulation, including asymmetric barriers for light.

  1. Request for Information on Photovoltaic Module Recycling

    Energy.gov [DOE]

    The U.S. Department of Energy SunShot Initiative requests feedback from industry, academia, research laboratories, government agencies, and other stakeholders on issues related to photovoltaic (PV) module recycling technology. SunShot intends to understand the current state of recycling technology and the areas of research that could lead to impactful recycling technologies to support the developing PV industry. The intent of this request for information is to generate discussion related to planning for the end of life of photovoltaic modules and to create a list of high impact research topics in photovoltaics recycling.

  2. RFID tag modification for full depth backscatter modulation

    DOEpatents

    Scott, Jeffrey Wayne [Pasco, WA; Pratt, Richard M [Richland, WA

    2010-07-20

    A modulated backscatter radio frequency identification device includes a diode detector configured to selectively modulate a reply signal onto an incoming continuous wave; communications circuitry configured to provide a modulation control signal to the diode detector, the diode detector being configured to modulate the reply signal in response to be modulation control signal; and circuitry configured to increase impedance change at the diode detector which would otherwise not occur because the diode detector rectifies the incoming continuous wave while modulating the reply signal, whereby reducing the rectified signal increases modulation depth by removing the reverse bias effects on impedance changes. Methods of improving depth of modulation in a modulated backscatter radio frequency identification device are also provided.

  3. Light modulated electron beam driven radiofrequency emitter

    DOEpatents

    Wilson, M.T.; Tallerico, P.J.

    1979-10-10

    The disclosure relates to a light modulated electron beam-driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

  4. Pulse width modulation inverter with battery charger

    DOEpatents

    Slicker, James M.

    1985-01-01

    An inverter is connected between a source of DC power and a three-phase AC induction motor, and a microprocessor-based circuit controls the inverter using pulse width modulation techniques. In the disclosed method of pulse width modulation, both edges of each pulse of a carrier pulse train are equally modulated by a time proportional to sin .theta., where .theta. is the angular displacement of the pulse center at the motor stator frequency from a fixed reference point on the carrier waveform. The carrier waveform frequency is a multiple of the motor stator frequency. The modulated pulse train is then applied to each of the motor phase inputs with respective phase shifts of 120.degree. at the stator frequency. Switching control commands for electronic switches in the inverter are stored in a random access memory (RAM) and the locations of the RAM are successively read out in a cyclic manner, each bit of a given RAM location controlling a respective phase input of the motor. The DC power source preferably comprises rechargeable batteries and all but one of the electronic switches in the inverter can be disabled, the remaining electronic switch being part of a "flyback" DC-DC converter circuit for recharging the battery.

  5. Light modulated switches and radio frequency emitters

    DOEpatents

    Wilson, Mahlon T.; Tallerico, Paul J.

    1982-01-01

    The disclosure relates to a light modulated electron beam driven radiofrequency emitter. Pulses of light impinge on a photoemissive device which generates an electron beam having the pulse characteristics of the light. The electron beam is accelerated through a radiofrequency resonator which produces radiofrequency emission in accordance with the electron, hence, the light pulses.

  6. WRAP Module 1 waste characterization plan

    SciTech Connect

    Mayancsik, B.A.

    1995-01-23

    The purpose of this document is to present the characterization methodology for waste generated, processed, or otherwise the responsibility of the Waste Receiving and Processing (WRAP) Module 1 facility. The scope of this document includes all solid low level waste (LLW), transuranic (TRU), mixed waste (MW), and dangerous waste. This document is not meant to be all-inclusive of the waste processed or generated within WRAP Module 1, but to present a methodology for characterization. As other streams are identified, the method of characterization will be consistent with the other streams identified in this plan. The WRAP Module 1 facility is located in the 200 West Area of the Hanford Site. The facility`s function is two-fold. The first is to verify/characterize, treat and repackage contact handled (CH) waste currently in retrievable storage in the LLW Burial Grounds, Hanford Central Waste Complex, and the Transuranic Storage and Assay Facility (TRUSAF). The second is to verify newly generated CH TRU waste and LLW, including MW. The WRAP Module 1 facility provides NDE and NDA of the waste for both drums and boxes. The NDE is used to identify the physical contents of the waste containers to support waste characterization and processing, verification, or certification. The NDA results determine the radioactive content and distribution of the waste.

  7. Dark-matter harmonics beyond annual modulation

    SciTech Connect

    Lee, Samuel K.; Lisanti, Mariangela; Safdi, Benjamin R. E-mail: mlisanti@princeton.edu

    2013-11-01

    The count rate at dark-matter direct-detection experiments should modulate annually due to the motion of the Earth around the Sun. We show that higher-frequency modulations, including daily modulation, are also present and in some cases are nearly as strong as the annual modulation. These higher-order modes are particularly relevant if (i) the dark matter is light, O(10) GeV, (ii) the scattering is inelastic, or (iii) velocity substructure is present; for these cases, the higher-frequency modes are potentially observable at current and ton-scale detectors. We derive simple expressions for the harmonic modes as functions of the astrophysical and geophysical parameters describing the Earth's orbit, using an updated expression for the Earth's velocity that corrects a common error in the literature. For an isotropic halo velocity distribution, certain ratios of the modes are approximately constant as a function of nuclear recoil energy. Anisotropic distributions can also leave observable features in the harmonic spectrum. Consequently, the higher-order harmonic modes are a powerful tool for identifying a potential signal from interactions with the Galactic dark-matter halo.

  8. Heat exchanger module for stirling engines

    SciTech Connect

    Darche, M. J. P.; Carlquist, S.

    1985-02-12

    The invention relates to Stirling engines and provides a modular assembly composed of a cylinder head, a heater, a regenerator, a cooler and a cold duct, and making it possible by mounting a plurality of identical modules on an engine assembly to construct a multi-cylinder double acting Stirling engine of the indirect heating type.

  9. Optical wavelength modulation in free electron lasers

    SciTech Connect

    Mabe, R.M.; Wong, R.K.; Colson, W.B.

    1995-12-31

    An attribute of the free electron laser (FEL) is the continuous tunability of the optical wavelength by modulation of the electron beam energy. The variation of the wavelength and power of the optical beam is studied as a function of FEL operating parameters. These results will be applied to the Stanford SCA FEL and Boeing FEL.

  10. Coherent pulse position modulation quantum cipher

    SciTech Connect

    Sohma, Masaki; Hirota, Osamu

    2014-12-04

    On the basis of fundamental idea of Yuen, we present a new type of quantum random cipher, where pulse position modulated signals are encrypted in the picture of quantum Gaussian wave form. We discuss the security of our proposed system with a phase mask encryption.

  11. 2013 Annual Merit Review Results Report - Merit Review Attendees |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy 3 Annual Merit Review Results Report - Merit Review Attendees 2013 Annual Merit Review Results Report - Merit Review Attendees Merit review of DOE Vehicle Technologies research activities 2013_amr_13.pdf (654.24 KB) More Documents & Publications 2014 Annual Merit Review Results Report - Merit Review Attendees Event Attendee List (Knoxville July 2012) Final Participant List

  12. Model documentation report: Commercial Sector Demand Module of the National Energy Modeling System

    SciTech Connect

    1998-01-01

    This report documents the objectives, analytical approach and development of the National Energy Modeling System (NEMS) Commercial Sector Demand Module. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components. The NEMS Commercial Sector Demand Module is a simulation tool based upon economic and engineering relationships that models commercial sector energy demands at the nine Census Division level of detail for eleven distinct categories of commercial buildings. Commercial equipment selections are performed for the major fuels of electricity, natural gas, and distillate fuel, for the major services of space heating, space cooling, water heating, ventilation, cooking, refrigeration, and lighting. The algorithm also models demand for the minor fuels of residual oil, liquefied petroleum gas, steam coal, motor gasoline, and kerosene, the renewable fuel sources of wood and municipal solid waste, and the minor services of office equipment. Section 2 of this report discusses the purpose of the model, detailing its objectives, primary input and output quantities, and the relationship of the Commercial Module to the other modules of the NEMS system. Section 3 of the report describes the rationale behind the model design, providing insights into further assumptions utilized in the model development process to this point. Section 3 also reviews alternative commercial sector modeling methodologies drawn from existing literature, providing a comparison to the chosen approach. Section 4 details the model structure, using graphics and text to illustrate model flows and key computations.

  13. Klystron Modulator Design for the Los Alamos Neutron Science Center Accelerator

    SciTech Connect

    Reass, William A.; Baca, David M.; Partridge, Edward R.; Rees, Daniel E.

    2012-06-22

    This paper will describe the design of the 44 modulator systems that will be installed to upgrade the Los Alamos Neutron Science Center (LANSCE) accelerator RF system. The klystrons can operate up to 86 kV with a nominal 32 Amp beam current with a 120 Hz repetition rate and 15% duty cycle. The klystrons are a mod-anode design. The modulator is designed with analog feedback control to ensure the klystron beam current is flat-top regulated. To achieve fast switching while maintaining linear feedback control, a grid-clamp, totem-pole modulator configuration is used with an 'on' deck and an 'off' deck. The on and off deck modulators are of identical design and utilize a cascode connected planar triode, cathode driven with a high speed MOSFET. The derived feedback is connected to the planar triode grid to enable the flat-top control. Although modern design approaches suggest solid state designs may be considered, the planar triode (Eimac Y-847B) is very cost effective, is easy to integrate with the existing hardware, and provides a simplified linear feedback control mechanism. The design is very compact and fault tolerant. This paper will review the complete electrical design, operational performance, and system characterization as applied to the LANSCE installation.

  14. Dual modulation laser line-locking technique for wavelength modulation spectroscopy

    DOEpatents

    Bomse, David S.; Hovde, D. Christian; Silver, Joel A.

    2002-01-01

    Disclosed are a method and apparatus for dual modulation of an optical spectroscopy laser. Demodulation is accomplished in a manner resulting in measurement of absorbance of a gas species, as well as stabilization of laser wavelength and baseline noise reduction.

  15. SOP for Peer Reviews

    Office of Energy Efficiency and Renewable Energy (EERE)

    Objective review and advice from peers - peer review - provides managers, staff, and researchers with a powerful and effective tool for enhancing the management, relevance, effectiveness, and productivity of all of the EERE research, development

  16. HUD's Environmental Review Training

    Energy.gov [DOE]

    An environmental review is the process of reviewing a project and its potential environmental impacts to determine whether it meets  federal, state, and local environmental standards. The...

  17. 2011 Peer Review Report

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Cover photo: Geysers Geothermal Power Plant, Calpine Geothermal Technologies Program 2011 Peer Review Report June 2011 U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Geothermal Technologies Program 2011 Peer Review Report June 2011 Allan Jelacic Chair 2011 Geothermal Technologies Peer Review Panel Douglas Hollett Program Manager U.S. DOE Geothermal Technologies Program Greg Stillman Peer Review Lead U.S. DOE Geothermal Technologies Program Table of Contents Executive

  18. 2002 Program Review Meeting

    Energy.gov [DOE]

    Here you'll find information from the Tribal Energy Program project kick-off and Review in October 2002.

  19. 2010 Program Review Meeting

    Office of Energy Efficiency and Renewable Energy (EERE)

    Here you'll find presentations from the October 2010 Tribal Energy Program Review in Denver, Colorado.

  20. Module Embedded Microinverter Smart Grid Ready Residential Solar Electric System

    Energy.gov [DOE]

    This project is developing and demonstrating a cost-reduction approach for an alternating-current (AC) photovoltaic (PV) module that is driven by innovations in microinverter design, module...

  1. Raising the Bar for Quality PV Modules | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Raising the Bar for Quality PV Modules Raising the Bar for Quality PV Modules October 30, 2014 - 4:58pm Addthis As photovoltaics (PV) markets expand across the United States the...

  2. 70005 MODULE AT-- U-X ASSY - Sh

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    5 MODULE AT-- U-X ASSY MODULE U-X ASS'Y 1:10 1 6 RSF RSF RSF 70005 21607 - 21607 - - - INITIAL ISSUE - - WEIGHT: 3081 LBS FRONT (UPSTREAM SIDE) Parts List ITEM NO. QTY...

  3. Photovoltaic Shading Testbed for Module-Level Power Electronics...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Photovoltaic Shading Testbed for Module-Level Power Electronics: 2016 Performance Data ... CO 80401 303-275-3000 * www.nrel.gov Photovoltaic Shading Testbed for Module-Level Power ...

  4. Hybrid metasurface for ultra-broadband terahertz modulation ...

    Office of Scientific and Technical Information (OSTI)

    Experimental validations confirm a bandwidth of at least 100%, spanning 0.5 to 1.5 THz with -10 dB modulation depth. This modulation depth is far superior to -5 dB achievable from ...

  5. Agenda for the PV Module Reliability Workshop, February 26 -...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Agenda for the PV Module Reliability Workshop, February 26 - 27 2013, Golden, Colorado ... More Documents & Publications PID Failure of c-Si and Thin-Film Modules and Possible ...

  6. Tailored Terahertz Pulses from a Laser-Modulated Electron Beam

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Tailored Terahertz Pulses from a Laser-Modulated Electron Beam Print Wednesday, 29 November 2006 00:00 Researchers at ...

  7. NREL and Sandia host PV Module Reliability Workshop, Feb. 23...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    and Sandia host PV Module Reliability Workshop, Feb. 23-25, 2016 - Sandia Energy Energy ... Twitter Google + Vimeo GovDelivery SlideShare NREL and Sandia host PV Module Reliability ...

  8. SolarBridge Technologies: Helping Solar Modules Speak the Language...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    SolarBridge Technologies: Helping Solar Modules Speak the Language of the Energy Grid SolarBridge Technologies: Helping Solar Modules Speak the Language of the Energy Grid June 5, ...

  9. Method and apparatus of highly linear optical modulation

    DOEpatents

    DeRose, Christopher; Watts, Michael R.

    2016-05-03

    In a new optical intensity modulator, a nonlinear change in refractive index is used to balance the nonlinearities in the optical transfer function in a way that leads to highly linear optical intensity modulation.

  10. Module-Integrated Power Converters Based on Universal Dock

    SciTech Connect

    Chapman, Patrick; Rodriguez, Fernando

    2015-03-13

    Solar power installations using alternating current photovoltaic (ACPV) modules have significant cost and performance advantages over systems using conventional solar modules and string inverters. ACPV modules have improved energy harvest due to module-level power point tracking and redundancy. More importantly, ACPV modules are easier and cheaper to install, lowering the total installed cost, indirect costs, and barriers to market entry. Furthermore, ACPV modules have communications and data logging capability, yielding module-level telemetry data that is useful in site diagnostics and other data applications. The products of these efforts were threefold. First, an advanced microinverter power topology was developed, modeled, simulated, and tested. Second, new microinverter enclosure concepts were developed and tested. Third, a new ACPV module prototype was constructed, combining the power topology and the enclosure concepts. SolarBridge filed for patents in each of these areas and is transitioning the project from a concept phase to full development.

  11. THE VEX RADIATION MODULE: 2D RADIATION TRANSPORT WITH MIMETIC...

    Office of Scientific and Technical Information (OSTI)

    THE VEX RADIATION MODULE: 2D RADIATION TRANSPORT WITH MIMETIC DIFFUSION FOR EXAFLAG Citation Details In-Document Search Title: THE VEX RADIATION MODULE: 2D RADIATION TRANSPORT WITH ...

  12. THE VEX RADIATION MODULE: 2D RADIATION TRANSPORT WITH MIMETIC...

    Office of Scientific and Technical Information (OSTI)

    THE VEX RADIATION MODULE: 2D RADIATION TRANSPORT WITH MIMETIC DIFFUSION FOR EXAFLAG Citation Details In-Document Search Title: THE VEX RADIATION MODULE: 2D RADIATION TRANSPORT WITH...

  13. Multidimensional signal modulation and/or demodulation for data communications

    DOEpatents

    Smith, Stephen F.; Dress, William B.

    2008-03-04

    Systems and methods are described for multidimensional signal modulation and/or demodulation for data communications. A method includes modulating a carrier signal in a first domain selected from the group consisting of phase, frequency, amplitude, polarization and spread; modulating the carrier signal in a second domain selected from the group consisting of phase, frequency, amplitude, polarization and spread; and modulating the carrier signal in a third domain selected from the group consisting of phase, frequency, amplitude, polarization and spread.

  14. DOE Technical Standards Policy & Procedures (TSPP) Tutorial Modules

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Available | Department of Energy Technical Standards Policy & Procedures (TSPP) Tutorial Modules Available DOE Technical Standards Policy & Procedures (TSPP) Tutorial Modules Available April 7, 2016 - 2:48pm Addthis DOE Technical Standards Policy & Procedures (TSPP) Tutorial Modules Available The DOE Technical Standards Policy & Procedures (TSPP) tutorial modules are intended to assist and outline the processes for initiating, developing, coordinating, and maintaining DOE

  15. Code division multiple access signaling for modulated reflector technology

    DOEpatents

    Briles, Scott D.

    2012-05-01

    A method and apparatus for utilizing code division multiple access in modulated reflectance transmissions comprises the steps of generating a phase-modulated reflectance data bit stream; modifying the modulated reflectance data bit stream; providing the modified modulated reflectance data bit stream to a switch that connects an antenna to an infinite impedance in the event a "+1" is to be sent, or connects the antenna to ground in the event a "0" or a "-1" is to be sent.

  16. Peer Reviews | Department of Energy

    Office of Environmental Management (EM)

    Peer Reviews Peer Reviews The overall purpose of project peer reviews is to determine whether the scope of programs, projects, or activities; the underlying assumptions regarding ...

  17. Energy Efficiency Post-2011 Review

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Summer Goodwin Danielle Gidding Meeting Notes: 1 Welcome and roll call Review of agenda Overview of progress to date Review of action items BPA reviewed...

  18. Rolling in the modulated reheating scenario

    SciTech Connect

    Kobayashi, Naoya; Kobayashi, Takeshi; Erickcek, Adrienne L. E-mail: takeshi@cita.utoronto.ca

    2014-01-01

    In the modulated reheating scenario, the field that drives inflation has a spatially varying decay rate, and the resulting inhomogeneous reheating process generates adiabatic perturbations. We examine the statistical properties of the density perturbations generated in this scenario. Unlike earlier analyses, we include the dynamics of the field that determines the inflaton decay rate. We show that the dynamics of this modulus field can significantly alter the amplitude of the power spectrum and the bispectrum, even if the modulus field has a simple potential and its effective mass is smaller than the Hubble rate. In some cases, the evolution of the modulus amplifies the non-Gaussianity of the perturbations to levels that are excluded by recent observations of the cosmic microwave background. Therefore, a proper treatment of the modulus dynamics is required to accurately calculate the statistical properties of the perturbations generated by modulated reheating.

  19. Photovoltaic module with light reflecting backskin

    DOEpatents

    Gonsiorawski, Ronald C.

    2007-07-03

    A photovoltaic module comprises electrically interconnected and mutually spaced photovoltaic cells that are encapsulated by a light-transmitting encapsulant between a light-transparent front cover and a back cover, with the back cover sheet being an ionomer/nylon alloy embossed with V-shaped grooves running in at least two directions and coated with a light reflecting medium so as to provide light-reflecting facets that are aligned with the spaces between adjacent cells and oriented so as to reflect light falling in those spaces back toward said transparent front cover for further internal reflection onto the solar cells, whereby substantially all of the reflected light will be internally reflected from said cover sheet back to the photovoltaic cells, thereby increasing the current output of the module. The internal reflector improves power output by as much as 67%.

  20. High-speed photonic modulator designs

    SciTech Connect

    DeRose, Christopher; Zortman, William A

    2015-02-03

    An optical device includes a microdisk optical resonator element. The microdisk resonator element is formed on a substrate and has upper and lower portions respectively distal and proximal the substrate. An arcuate semiconductor contact region partially surrounds the microdisk resonator element. A first modulator electrode is centrally formed on the upper portion of the microdisk resonator element, and a second modulator electrode is formed on the arcuate contact region. A laminar semiconductor region smaller in thickness than the microdisk resonator element separates the arcuate contact region from the microdisk resonator element and is formed on the substrate so as to electrically connect the arcuate contact region to the lower portion of the microdisk resonator element.

  1. Results from the Second International Module Intercomparison

    SciTech Connect

    Rummel, S.; Anderberg, A.; Emery, K.

    2005-11-01

    The peak-watt rating is a primary indicator of PV performance. The peak power rating is the maximum electrical power that is produced when the PV device is continuously illuminated at 1000 Wm/sup-2/ total irradiance under International Electrotechnical Commission Standard 60904-2 reference spectrum, and 25 deg C cell temperature. Most manufacturers trace their peak-watt rating through calibrations performed at recognized terrestrial calibration facilities. Manufacturers typically perform intercomparisons among a set of their modules internally with other plants and among. Sometimes they have the same module measured at different calibration facilities to determine the differences in calibration. This intercomparison was to mimic this procedure and supply new thin film samples along with samples that could pose other problems. These intercomparisons sample the laboratories' everyday procedures better than a formal intercomparison where the laboratories' best procedures and data scrutiny are used.

  2. Hot gas cross flow filtering module

    DOEpatents

    Lippert, Thomas E.; Ciliberti, David F.

    1988-01-01

    A filter module for use in filtering particulates from a high temperature gas has a central gas duct and at least one horizontally extending support mount affixed to the duct. The support mount supports a filter element thereon and has a chamber therein, which communicates with an inner space of the duct through an opening in the wall of the duct, and which communicates with the clean gas face of the filter element. The filter element is secured to the support mount over an opening in the top wall of the support mount, with releasable securement provided to enable replacement of the filter element when desired. Ceramic springs may be used in connection with the filter module either to secure a filter element to a support mount or to prevent delamination of the filter element during blowback.

  3. Annual Review | netl.doe.gov

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ON-SITE RESEARCH PUBLICATIONS Annual Reviews FY13 Annual Review FY12 Annual Review FY11 Annual Review...

  4. Hole-thru-laminate mounting supports for photovoltaic modules

    DOEpatents

    Wexler, Jason; Botkin, Jonathan; Culligan, Matthew; Detrick, Adam

    2015-02-17

    A mounting support for a photovoltaic module is described. The mounting support includes a pedestal having a surface adaptable to receive a flat side of a photovoltaic module laminate. A hole is disposed in the pedestal, the hole adaptable to receive a bolt or a pin used to couple the pedestal to the flat side of the photovoltaic module laminate.

  5. World Energy Projection System Plus (WEPS ): Global Activity Module

    Reports and Publications

    2013-01-01

    World Energy Projection System Plus Model Documentation: Global Activity Module Documents the objectives, analytical approach, and development of the World Energy Projection Plus (WEPS ) Global Activity Module (GAM) used to develop the International Energy Outlook for 2013 (IEO2013). The report catalogues and describes the module assumptions, computations, methodology, parameter estimation techniques, and mainframe source code.

  6. Alternative Energy Sources -- An Interdisciplinary Module for Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Education | Department of Energy - An Interdisciplinary Module for Energy Education Alternative Energy Sources -- An Interdisciplinary Module for Energy Education Find activities focused on renewable energy sources such as solar and wind. lesson302.pdf (735.79 KB) More Documents & Publications Alternative Energy Sources - An Interdisciplinary Module for Energy Education Alternative Energy Sources

  7. Solar Photovoltaic Cell/Module Shipments Report

    Energy Information Administration (EIA) (indexed site)

    Solar Photovoltaic Cell/Module Shipments Report September 2016 Independent Statistics & Analysis www.eia.gov U.S. Department of Energy Washington, DC 20585 U.S. Energy Information Administration | Improving the Quality and Scope of EIA Data i This report was prepared by the U.S. Energy Information Administration (EIA), the statistical and analytical agency within the U.S. Department of Energy. By law, EIA's data, analyses, and forecasts are independent of approval by any other officer or

  8. Effects of Metastabilities on CIGS Photovoltaic Modules

    Energy.gov [DOE]

    This poster describes a SunShot Initiative solar project led by a team from Nexcis Photovoltaic Technology entitled "Effects of Metastabilities on CIGS Photovoltaic Modules." The team studied the driving force of the mechanisms which governs the different observed phases during storage, light exposition and annealing. The aim of this study is to obtain a better understanding of this phenomenon and hence a better evaluation of its impact on solar panel reliability.

  9. Positive modulator of bone morphogenic protein-2

    DOEpatents

    Zamora, Paul O.; Pena, Louis A.; Lin, Xinhua; Takahashi, Kazuyuki

    2009-01-27

    Compounds of the present invention of formula I and formula II are disclosed in the specification and wherein the compounds are modulators of Bone Morphogenic Protein activity. Compounds are synthetic peptides having a non-growth factor heparin binding region, a linker, and sequences that bind specifically to a receptor for Bone Morphogenic Protein. Uses of compounds of the present invention in the treatment of bone lesions, degenerative joint disease and to enhance bone formation are disclosed.

  10. Solar Cell Modules With Improved Backskin

    DOEpatents

    Gonsiorawski, Ronald C.

    2003-12-09

    A laminated solar cell module comprises a front light transmitting support, a plurality of interconnected solar cells encapsulated by a light-transmitting encapsulant material, and an improved backskin formed of an ionomer/nylon alloy. The improved backskin has a toughness and melting point temperature sufficiently great to avoid any likelihood of it being pierced by any of the components that interconnect the solar cells.

  11. Downhole drilling network using burst modulation techniques

    DOEpatents

    Hall; David R. , Fox; Joe

    2007-04-03

    A downhole drilling system is disclosed in one aspect of the present invention as including a drill string and a transmission line integrated into the drill string. Multiple network nodes are installed at selected intervals along the drill string and are adapted to communicate with one another through the transmission line. In order to efficiently allocate the available bandwidth, the network nodes are configured to use any of numerous burst modulation techniques to transmit data.

  12. Solar module having reflector between cells

    DOEpatents

    Kardauskas, Michael J.

    1999-01-01

    A photovoltaic module comprising an array of electrically interconnected photovoltaic cells disposed in a planar and mutually spaced relationship between a light-transparent front cover member in sheet form and a back sheet structure is provided with a novel light-reflecting means disposed between adjacent cells for reflecting light falling in the areas between cells back toward said transparent cover member for further internal reflection onto the solar cells. The light-reflecting comprises a flexible plastic film that has been embossed so as to have a plurality of small V-shaped grooves in its front surface, and a thin light-reflecting coating on said front surface, the portions of said coating along the sides of said grooves forming light-reflecting facets, said grooves being formed so that said facets will reflect light impinging thereon back into said transparent cover sheet with an angle of incidence greater than the critical angle, whereby substantially all of the reflected light will be internally reflected from said cover sheet back to said solar modules, thereby increasing the current output of the module.

  13. Low thermal resistance power module assembly

    DOEpatents

    Hassani, Vahab; Vlahinos, Andreas; Bharathan, Desikan

    2010-12-28

    A power module assembly (400) with low thermal resistance and enhanced heat dissipation to a cooling medium. The assembly includes a heat sink or spreader plate (410) with passageways or openings (414) for coolant that extend through the plate from a lower surface (411) to an upper surface (412). A circuit substrate (420) is provided and positioned on the spreader plate (410) to cover the coolant passageways. The circuit substrate (420) includes a bonding layer (422) configured to extend about the periphery of each of the coolant passageways and is made up of a substantially nonporous material. The bonding layer (422) may be solder material which bonds to the upper surface (412) of the plate to provide a continuous seal around the upper edge of each opening (414) in the plate. The assembly includes power modules (430) mounted on the circuit substrate (420) on a surface opposite the bonding layer (422). The power modules (430) are positioned over or proximal to the coolant passageways.

  14. Determination of Thermoelectric Module Efficiency A Survey

    SciTech Connect

    Wang, Hsin; McCarty, Robin; Salvador, James R.; Yamamoto, Atsushi; Konig, Jan

    2014-01-01

    The development of thermoelectrics (TE) for energy conversion is in the transition phase from laboratory research to device development. There is an increasing demand to accurately determine the module efficiency, especially for the power generation mode. For many thermoelectrics, the figure of merit, ZT, of the material sometimes cannot be fully realized at the device level. Reliable efficiency testing of thermoelectric modules is important to assess the device ZT and provide the end-users with realistic values on how much power can be generated under specific conditions. We conducted a general survey of efficiency testing devices and their performance. The results indicated the lack of industry standards and test procedures. This study included a commercial test system and several laboratory systems. Most systems are based on the heat flow meter method and some are based on the Harman method. They are usually reproducible in evaluating thermoelectric modules. However, cross-checking among different systems often showed large errors that are likely caused by unaccounted heat loss and thermal resistance. Efficiency testing is an important area for the thermoelectric community to focus on. A follow-up international standardization effort is planned.

  15. Designed TPR Modules as Novel Anticancer Agents

    SciTech Connect

    Cortajarena,A.; Yi, F.; Regan, L.

    2008-01-01

    Molecules specifically designed to modulate protein-protein interactions have tremendous potential as novel therapeutic agents. One important anticancer target is the chaperone Hsp90, whose activity is essential for the folding of many oncogenic proteins, including HER2, IGFIR, AKT, RAF-1, and FLT-3. Here we report the design and characterization of new tetratricopeptide repeat modules, which bind to the C-terminus of Hsp90 with higher affinity and with greater specificity than natural Hsp90-binding co-chaperones. Thus, when these modules are introduced into the cell, they out-compete endogenous co-chaperones for binding, thereby inhibiting Hsp90 function. The effect of Hsp90 inhibition in this fashion is dramatic; HER2 levels are substantially decreased and BT474 HER2 positive breast cancer cells are killed. Our designs thus provide new tools with which to dissect the mechanism of Hsp90-mediated protein folding and also open the door to the development of an entirely new class of anticancer agents.

  16. Development of an Outdoor Concentrating Photovoltaic Module Testbed, Module Handling and Testing Procedures, and Initial Energy Production Results

    SciTech Connect

    Muller, M.

    2009-09-01

    This report addresses the various aspects of setting up a CPV testbed and procedures for handling and testing CPV modules.

  17. scriptEnv - loading modules before starting a script

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    scriptEnv - loading modules before starting a script scriptEnv - loading modules before starting a script In some cases a script needs to load modules before the script can be executed, but it can often be inconvenient or impossible to provide wrapper scripts which load the needed modules. CGI scripts on the gpweb resources or in the NERSC portal environment which require the genepool-specific python/perl/R or databases configuration modules are a strong example of this. NERSC provides the

  18. EIA model documentation: Electricity market module - electricity fuel dispatch

    SciTech Connect

    1997-01-01

    This report documents the National Energy Modeling System Electricity Fuel Dispatch Submodule (EFD), a submodule of the Electricity Market Module (EMM) as it was used for EIA`s Annual Energy Outlook 1997. It replaces previous documentation dated March 1994 and subsequent yearly update revisions. The report catalogues and describes the model assumptions, computational methodology, parameter estimation techniques, model source code, and forecast results generated through the synthesis and scenario development based on these components. This document serves four purposes. First, it is a reference document providing a detailed description of the model for reviewers and potential users of the EFD including energy experts at the Energy Information Administration (EIA), other Federal agencies, state energy agencies, private firms such as utilities and consulting firms, and non-profit groups such as consumer and environmental groups. Second, this report meets the legal requirement of the Energy Information Administration (EIA) to provide adequate documentation in support of its statistical and forecast reports. Third, it facilitates continuity in model development by providing documentation which details model enhancements that were undertaken for AE097 and since the previous documentation. Last, because the major use of the EFD is to develop forecasts, this documentation explains the calculations, major inputs and assumptions which were used to generate the AE097.

  19. National Algal Biofuels Technology Review

    Office of Energy Efficiency and Renewable Energy (EERE)

    Plenary V: National Algal Biofuels Technology Review National Algal Biofuels Technology Review Matthew Posewitz, Professor, Colorado School of Mines

  20. Peer Reviews | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Peer Reviews Peer Reviews September 30, 2015 Audit Peer Review 2015 Report on Quality Control Review of the Department of Energy, Office of Inspector General, Audit Organization July 14, 2014 Investigation Peer Review 2014 Report on the Quality Assessment Review of the Investigative Operations of the Office of Inspector General for the U.S. Department of Energy February 20, 2014 Investigation Peer Review 2012 Report on the Quality Assessment Review of the Investigative Outcomes of the Office of

  1. Lightweight photovoltaic module development for unmanned aerial vehicles

    SciTech Connect

    Nowlan, M.J.; Maglitta, J.C.; Lamp, T.R.

    1998-07-01

    Lightweight photovoltaic modules are being developed for powering high altitude unmanned aerial vehicles (UAVs). Terrestrial crystalline silicon solar cell and module technologies are being applied to minimize module cost, with modifications to improve module specific power (W/kg) and power density (W/m{sup 2}). New module processes are being developed for assembling standard thickness (320 mm) and thin (125 mm) solar cells, thin (50 to 100 mm) encapsulant films, and thin (25 mm) cover films. In comparison, typical terrestrial modules use 300 to 400 mm thick solar cells, 460 mm thick encapsulants, and 3.2 mm thick glass covers. The use of thin, lightweight materials allows the fabrication of modules with specific powers ranging from 120 to 200 W/kg, depending on cell thickness and efficiency, compared to 15 W/kg or less for conventional terrestrial modules. High efficiency designs based on ultra-thin (5 mm) GaAs cells have also been developed, with the potential for achieving substantially higher specific powers. Initial design, development, and module assembly work is completed. Prototype modules were fabricated in sizes up to 45 cm x 99 cm. Module materials and processes are being evaluated through accelerated environmental testing, including thermal cycling, humidity-freeze cycling, mechanical cycling, and exposure to UV and visible light.

  2. Materials and Modules for Low Cost, High Performance Fuel Cell Humidifiers

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Kick-off Meeting, Wash. D.C - 10/01/2009 Materials and Modules for Low Cost, High Performance Fuel Cell Humidifiers Prime Contractor: W. L. Gore & Associates Elkton, MD Principal Investigator: William B. Johnson Sub-Contractor: dPoint Technologies Vancouver, BC W. L. Gore & Associates, Inc. DOE Kick-off Meeting, Wash. D.C - 10/01/2009 Ahluwalia, et. al, ibid. Mirza, Z. DOE Hydrogen Program Review, June 9-13, 2008; Washington, DC Background W. L. Gore & Associates, Inc. DOE Kick-off

  3. ARM - Guidelines : Review Criteria

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Review Criteria Guidelines Overview Annual Facility Call Proposal Deadline Guidance Small Field Campaigns Review Criteria Expectations for Principal Investigators Forms Propose a Campaign Instrument Support Request (ISR) Form (Word, 89KB) Unmanned Aerial System (UAS) Mission Request Form (Word, 72KB) Documentation Submitting Field Campaign Data and Metadata Field Campaign Guidelines (PDF, 574KB) Unmanned Aerial System Operation Safety at ARM Sites (PDF, 639KB) Guidelines : Review Criteria

  4. 2013 Year in Review

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3 Year in Review i 2013 YIR May 2014 Year-in-Review: 2013 Energy Infrastructure Events and Expansions Infrastructure Security and Energy Restoration Office of Electricity Delivery and Energy Reliability U.S. Department of Energy DOE / 2013 Year in Review ii 2013 YIR For Further Information This report was prepared by the Office of Electricity Delivery and Energy Reliability under the direction of Patricia Hoffman, Assistant Secretary, and William Bryan, Deputy Assistant Secretary. Specific

  5. Internal Program Review

    Energy Saver

    National Energy Laboratories | Department of Energy Interim Report of the Commission to Review the Effectiveness of the National Energy Laboratories Interim Report of the Commission to Review the Effectiveness of the National Energy Laboratories This Interim Report presents the preliminary observations and recommendations gleaned from Phase I of the study by the Commission to Review the Effectiveness of the National Energy Laboratories (Commission). Key issues of the report focus on the

  6. 2015 Project Peer Review

    Energy.gov [DOE]

    The Bioenergy Technologies Office is hosting the 2015 Peer Review on March 23–27, 2015, at the Hilton Mark Center, in Alexandria, Virginia.

  7. Vehicle Emissions Review- 2011

    Energy.gov [DOE]

    Reviews regulatory requirements and general technology approaches for heavy- and light-duty vehicle emissions control - filter technology, new catalysts, NOx control, diesel oxidation catalysts, gasoline particulate filters

  8. Calculation note review

    SciTech Connect

    Ramble, A.L.

    1996-09-30

    This document contains a review of the calculation notes which were prepared for the Tank Waste Remediation System Basis for Interim Operation.

  9. External Technical Review Report

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    ... 34 Attachment F, ETR Report Format ... Readiness Review or Readiness Assessment ETRs are not required ... If a design technology, process, or system is new, ...

  10. 2015 Peer Review | Plenaries

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Energy Department conducted its periodic rigorous, independent peer review of the geothermal portfolio in May 2015. Plenary sessions provided insight into the progress in this energy sector.

  11. STANDARD REVIEW PLAN

    Office of Environmental Management (EM)

    Strengthening Line Management Oversight and Federal Monitoring of Nuclear Facilities Standard Review Plan Safety Design Strategy January 2015 OFFICE OF ENVIRONMENTAL MANAGEMENT ...

  12. Monthly Energy Review

    Annual Energy Outlook

    December 23, 1997 Electronic Access Monthly Energy Review (MER) data are also available through these electronic means: * ASCII text, Lotus (wk1), and Excel (xls) versions of the...

  13. Quadrennial Energy Review Meeting

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Quadrennial Energy Review Meeting September 8, 2014 Commissioner Garry Brown, NYS Public Service Commission Topic: Business Models and Regulation of Regulated Utilities - Do They ...

  14. Requirement-Reviews.pptx

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    1, 2 013 Requirements Reviews * 1½-day reviews with each Program Office * Computing and storage requirements for next 5 years * Participants - DOE ADs & Program Managers - Leading scientists using NERSC & key potential users - NERSC staff 2 High Energy Physics Fusion R esearch Reports From 6 Requirements Reviews Have Been Published 3 h%p://www.nersc.gov/science/requirements---reviews/ final---reports/ * Compu<ng a nd s torage requirements f or 2013/2014 * Execu<ve S ummary o f

  15. 2013 Financial Review

    Annual Energy Outlook

    Review Brief description of terms 3 * Cash from operations is a measure of income. * Capital expenditures represent cash used for property, plant, and equipment (investing...

  16. EERE Strategic Program Review

    SciTech Connect

    None, None

    2002-03-01

    This Strategic Program Review presents the result of recommendations of the National Energy Policy Development Group as stated in the National Energy Policy.

  17. EWONAP Environmental Review

    Energy.gov [DOE]

    HUD's Eastern Woodlands Office of Native American Programs in collaboration with the Seminole Tribe of Florida Native Learning Center invites you to attend the Environmental Review Training...

  18. EERE Strategic Program Review

    Energy Saver

    ... Light Source Basic Research Projects Materials ... At the same time, advances in materials science, information ... Lightweight Materials Program 1997 NRC Review of the ...

  19. EERE Strategic Program Review

    Energy.gov [DOE]

    This Strategic Program Review presents the result of recommendations of the National Energy Policy Development Group as stated in the National Energy Policy.

  20. Independent Peer Reviews

    SciTech Connect

    2012-03-16

    Independent Assessments: DOE's Systems Integrator convenes independent technical reviews to gauge progress toward meeting specific technical targets and to provide technical information necessary for key decisions.

  1. From: Post 2011 Review

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Inform BPA of willingness to host regional meetings Sign up to receive future communication regarding the Post-2011 Review BPA will issue a final scoping document later...

  2. Advanced Low Temperature Absorption Chiller Module Integrated with a CHP System at a Distributed Data Center- Presentation by Exergy Partners Corp., June 2011

    Energy.gov [DOE]

    Presentation on Develop & Demonstrate an Advanced Low Temp Heat Recovery Absorption Chiller Module, given by Richard Sweetser of Exergy Partners Corp., at the U.S. DOE Industrial Distributed Energy Portfolio Review Meeting in Washington, D.C. on June 1-2, 2011.

  3. Table 9. U.S. Photovoltaic module shipments by state/territory...

    Energy Information Administration (EIA) (indexed site)

    Photovoltaic module shipments by stateterritory, 2015 (peak kilowatts)" ... Administration, Form EIA-63B, 'Annual Photovoltaic CellModule Shipments Report.' ...

  4. HERA BEAM TAIL SHAPING BY TUNE MODULATION.

    SciTech Connect

    MONTAG,C.

    2003-05-19

    To study CP violation, the HEM-B experiment uses an internal wire target in the transverse halo of the stored HERA proton beam. Operational experience shows that the resulting interaction rates are extremely sensitive to tiny orbit jitter amplitudes. Various methods have been studied to stabilize these interaction rates by increasing diffusion in the transverse proton beam tails without affecting the luminosity at the electron-proton collider experiments ZEUS and H1. Tune modulation was found to be a promising method for this task. Experiments performed in recent years will be reported.

  5. Figure F2. Electricity market module regions

    Energy Information Administration (EIA) (indexed site)

    F-3 U.S. Energy Information Administration | Annual Energy Outlook 2016 Regional maps Figure F2. Electricity market module regions Source: U.S. Energy Information Administration, Office of Energy Analysis. 1 2 3 4 5 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 6 7 1. ERCT TRE All 2. FRCC FRCC All 3. MROE MRO East 4. MROW MRO West 5. NEWE NPCC New England 6. NYCW NPCC NYC/Westchester 7. NYLI NPCC Long Island 8. NYUP NPCC Upstate NY 9. RFCE RFC East 10. RFCM RFC Michigan 11. RFCW RFC West 12. SRDA

  6. Processing incommensurately modulated protein diffraction data with Eval15

    SciTech Connect

    Porta, Jason; Lovelace, Jeffrey J.; Schreurs, Antoine M. M.; Kroon-Batenburg, Loes M. J.; Borgstahl, Gloria E. O.

    2011-07-01

    Data processing of an incommensurately modulated profilin–actin crystal is described. Recent challenges in biological X-ray crystallography include the processing of modulated diffraction data. A modulated crystal has lost its three-dimensional translational symmetry but retains long-range order that can be restored by refining a periodic modulation function. The presence of a crystal modulation is indicated by an X-ray diffraction pattern with periodic main reflections flanked by off-lattice satellite reflections. While the periodic main reflections can easily be indexed using three reciprocal-lattice vectors a*, b*, c*, the satellite reflections have a non-integral relationship to the main lattice and require a q vector for indexing. While methods for the processing of diffraction intensities from modulated small-molecule crystals are well developed, they have not been applied in protein crystallography. A recipe is presented here for processing incommensurately modulated data from a macromolecular crystal using the Eval program suite. The diffraction data are from an incommensurately modulated crystal of profilin–actin with single-order satellites parallel to b*. The steps taken in this report can be used as a guide for protein crystallographers when encountering crystal modulations. To our knowledge, this is the first report of the processing of data from an incommensurately modulated macromolecular crystal.

  7. Quality Procedure- Document Review

    Office of Energy Efficiency and Renewable Energy (EERE)

    This procedure establishes the process for the review and approval of Environmental Management (EM) Quality Assurance (QA) program documents as performed by the Office of Standards and Quality Assurance. This procedure also establishes the process for review and approval of other EM documents external to the EM Headquarters Office of Standards and Quality Assurance.

  8. 2016 Annual Merit Review

    Energy.gov [DOE]

    At the Annual Merit Review and Peer Evaluation, project investigators present information on their efforts that have been financially supported by the Vehicle Technologies Office in the last year. Expert reviewers then evaluate these projects based on how much they contribute to or advance the Energy Department’s missions and goals.

  9. Office of Document Reviews

    Energy.gov [DOE]

    The Office of Document Reviews ensures that all documents prepared at DOE Headquarters are properly marked to identify the level and category of protected information they contain (if any) and to ensure that all documents the Department prepares or is required to review under applicable statutes for public release contain no information requiring protection under law, regulations and Executive orders.

  10. Technical Review Panel Report

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    TRP Report v7, 12 Aug 2012 TRP Report Final December 2012 Advanced Reactor Concepts Technical Review Panel Report Evaluation and Identification of future R&D on eight Advanced Reactor Concepts, conducted April - September 2012 December 2012 Public release version 2 Public release version 3 Table of Contents Summary ................................................................................................................................... 4 1. Overview of the Technical Review Panel

  11. EMBODY(Environmental Modules Build System Software)

    Energy Science and Technology Software Center

    2009-02-09

    Embody (Environment Modules Build) is a software build tool with integrated support for the environment-modules package. The tool eases and automates the task of building and installing software packages from source or binary distributions, as well as the management of associated modulefiles. An administrator or software pool maintainer has to write a brief script for the installation process. These steps are usually described for manual execution, in a package's README or INSTALL file. It wouldmore » be up to the site administrator to work out a procedure to capture the steps taken. This tool: streamlines and codifies the installation tasks in a common framework; it provides a self-documenting and unified way for maintaining package installations; uses bash shell variables and functions for portability; keeps log files of the proceedings. It is similar in intent and function to other existing tools, such as RPM, but has several novel features tailored for High Performance Computing (HPC) software deployments. The design goal is simplicity and decoupling from RPM's dependencies and its database, which enables coexistence of several builds. Useful on HPC systems, new builds can be deployed centrally to shared file systems and without affecting running jobs.« less

  12. MELCOR Peer Review

    SciTech Connect

    Boyack, B.E.; Dhir, V.K.; Gieseke, J.A.; Haste, T.J.; Kenton, M.A.; Khatib-Rahbar, M.; Leonard, M.T.; Viskanta, R.

    1992-03-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. The newest version of MELCOR is Version 1.8.1, July 1991. MELCOR development has reached the point that the United States Nuclear Regulatory Commission sponsored a broad technical review by recognized experts to determine or confirm the technical adequacy of the code for the serious and complex analyses it is expected to perform. For this purpose, an eight-member MELCOR Peer Review Committee was organized. The Committee has completed its review of the MELCOR code: the review process and findings of the MELCOR Peer Review Committee are documented in this report. The Committee has determined that recommendations in five areas are appropriate: (1) MELCOR numerics, (2) models missing from MELCOR Version 1.8.1, (3) existing MELCOR models needing revision, (4) the need for expanded MELCOR assessment, and (5) documentation.

  13. Program Management Review Opening Presentation

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    July 30, 2013 Valerie Reed Acting Director Program Management Review Bioenergy Technologies Office 2 Program Management Review May 20-24 th - Alexandria, VA * 219 projects reviewed * $1.595 Billion * 42 External Reviewers July 30th - Washington, D.C. * Project Review Results * 7 Key Platforms * BETO Programmatic Presentations * 7 Steering Committee Members 3 Peer Review Process 2013 Peer Review BETO Steering Group  Valerie Reed, Acting Director  Kevin Craig, Conversion Program Manager 

  14. Estimating service lifetimes of a polymer encapsulant for photovoltaic modules from accelerated testing

    SciTech Connect

    Czanderna, A.W.; Pern, F.J.

    1996-05-01

    In this paper, most of the emphasis is on A9918 ethylene vinyl acetate (EVA) used commercially as the pottant for encapsulating photovoltaic (PV) modules, in which the efficiencies in field-deployed modules have been reduced by 10-70% in 4-12 years. Yet, projections were made by several different research groups in the 1980s that the EVA lifetime could range from 2-100 years. The authors (1) elucidate the complexity of the encapsulation problem, (2) indicate the performance losses reported for PV systems deployed since 1981, (3) critically assess the service lifetime predictions for EVA as a PV pottant based on studies by others for which they review the inherent errors in their assumptions about the Arrhenius relation, (4) show how degradation of minimodules in laboratory experiments that simulate reality can produce efficiency losses comparable to those in field-degraded PV modules reported in the literature, and (5) outline an acceptable methodology for making a service lifetime prediction of the polymer encapsulant, including the essential need for relating accelerated lifetime testing to real-time testing with a sufficient number of samples.

  15. Support arrangement for core modules of nuclear reactors

    DOEpatents

    Bollinger, Lawrence R.

    1987-01-01

    A support arrangement is provided for the core modules of a nuclear reactor which provides support access through the control drive mechanisms of the reactor. This arrangement provides axial support of individual reactor core modules from the pressure vessel head in a manner which permits attachment and detachment of the modules from the head to be accomplished through the control drive mechanisms after their leadscrews have been removed. The arrangement includes a module support nut which is suspended from the pressure vessel head and screw threaded to the shroud housing for the module. A spline lock prevents loosening of the screw connection. An installation tool assembly, including a cell lifting and preloading tool and a torquing tool, fits through the control drive mechanism and provides lifting of the shroud housing while disconnecting the spline lock, as well as application of torque to the module support nut.

  16. Support arrangements for core modules of nuclear reactors. [PWR

    DOEpatents

    Bollinger, L.R.

    1983-11-03

    A support arrangement is provided for the core modules of a nuclear reactor which provides support access through the control drive mechanisms of the reactor. This arrangement provides axial support of individual reactor core modules from the pressure vessel head in a manner which permits attachment and detachment of the modules from the head to be accomplished through the control drive mechanisms after their leadscrews have been removed. The arrangement includes a module support nut which is suspended from the pressure vessel head and screw threaded to the shroud housing for the module. A spline lock prevents loosening of the screw connection. An installation tool assembly, including a cell lifting and preloading tool and a torquing tool, fits through the control drive mechanism and provides lifting of the shroud housing while disconnecting the spline lock, as well as application of torque to the module support nut.

  17. Design specifications for manufacturability of MCM-C multichip modules

    SciTech Connect

    Allen, C.; Blazek, R.; Desch, J.; Elarton, J.; Kautz, D.; Markley, D.; Morgenstern, H.; Stewart, R.; Warner, L.

    1995-06-01

    The scope of this document is to establish design guidelines for electronic circuitry packaged as multichip modules of the ceramic substrate variety, although many of these guidelines are applicable to other types of multichip modules. The guidelines begin with prerequisite information which must be developed between customer and designer of the multichip module. The core of the guidelines focuses on the many considerations that must be addressed during the multichip module design. The guidelines conclude with the resulting deliverables from the design which satisfy customer requirements and/or support the multichip module fabrication and testing processes. Considerable supporting information, checklists, and design constraints are captured in specific appendices and used as reference information in the main body text. Finally some real examples of multichip module design are presented.

  18. Quantifying Solar Cell Cracks in Photovoltaic Modules by Electroluminescence Imaging

    SciTech Connect

    Spataru, Sergiu; Hacke, Peter; Sera, Dezso; Glick, Stephen; Kerekes, Tamas; Teodorescu, Remus

    2015-06-14

    This article proposes a method for quantifying the percentage of partially and totally disconnected solar cell cracks by analyzing electroluminescence images of the photovoltaic module taken under high- and low-current forward bias. The method is based on the analysis of the module's electroluminescence intensity distribution, applied at module and cell level. These concepts are demonstrated on a crystalline silicon photovoltaic module that was subjected to several rounds of mechanical loading and humidity-freeze cycling, causing increasing levels of solar cell cracks. The proposed method can be used as a diagnostic tool to rate cell damage or quality of modules after transportation. Moreover, the method can be automated and used in quality control for module manufacturers, installers, or as a diagnostic tool by plant operators and diagnostic service providers.

  19. A solar module fabrication process for HALE solar electric UAVs

    SciTech Connect

    Carey, P.G.; Aceves, R.C.; Colella, N.J.; Williams, K.A.; Sinton, R.A.; Glenn, G.S.

    1994-12-12

    We describe a fabrication process used to manufacture high power-to-weight-ratio flexible solar array modules for use on high-altitude-long-endurance (HALE) solar-electric unmanned air vehicles (UAVs). These modules have achieved power-to-weight ratios of 315 and 396 W/kg for 150{mu}m-thick monofacial and 110{mu}m-thick bifacial silicon solar cells, respectively. These calculations reflect average module efficiencies of 15.3% (150{mu}m) and 14.7% (110{mu}m) obtained from electrical tests performed by Spectrolab, Inc. under AMO global conditions at 25{degrees}C, and include weight contributions from all module components (solar cells, lamination material, bypass diodes, interconnect wires, and adhesive tape used to attach the modules to the wing). The fabrication, testing, and performance of 32 m{sup 2} of these modules will be described.

  20. Microsoft Word - RM Handbook September 2006 final 1

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    CHAPTER IV - SPECIAL CATEGORIES OF RECORDS 1. General .......................................................................................... 32 2. Classified Records ............................................................................. 32 3. Sensitive Unclassified Records .............................................................. 32 4. Epidemiological and Other Health Study Records ......................................... 32 5. Government-Owned Records