National Library of Energy BETA

Sample records for refine clear-sky reference

  1. Establishing the Clear-Sky Diffuse Reference for BORCAL Using EPLAB Model 8-48 Pyranometers at the National Renewable Energ...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Establishing the Clear-Sky Diffuse Reference for BORCAL Using EPLAB Model 8-48 Pyranometers at the National Renewable Energy Laboratory I. Reda, T. L. Stoffel, and D. Myers National Renewable Energy Laboratory Golden, Colorado Abstract Precision pyranometer calibrations are important to the quality of Atmospheric Radiation Measurement's (ARM's) shortwave solar irradiance measurements. Calibrations at the National Renewable Energy Laboratory (NREL) and Southern Great Plains (SGP) are under

  2. Global horizontal irradiance clear sky models : implementation and analysis.

    SciTech Connect

    Stein, Joshua S.; Hansen, Clifford W.; Reno, Matthew J.

    2012-03-01

    Clear sky models estimate the terrestrial solar radiation under a cloudless sky as a function of the solar elevation angle, site altitude, aerosol concentration, water vapor, and various atmospheric conditions. This report provides an overview of a number of global horizontal irradiance (GHI) clear sky models from very simple to complex. Validation of clear-sky models requires comparison of model results to measured irradiance during clear-sky periods. To facilitate validation, we present a new algorithm for automatically identifying clear-sky periods in a time series of GHI measurements. We evaluate the performance of selected clear-sky models using measured data from 30 different sites, totaling about 300 site-years of data. We analyze the variation of these errors across time and location. In terms of error averaged over all locations and times, we found that complex models that correctly account for all the atmospheric parameters are slightly more accurate than other models, but, primarily at low elevations, comparable accuracy can be obtained from some simpler models. However, simpler models often exhibit errors that vary with time of day and season, whereas the errors for complex models vary less over time.

  3. A simple formula for determining globally clear skies

    SciTech Connect

    Long, C.N.; George, A.T.; Mace, G.G.

    1996-04-01

    Surface measurements to serve as {open_quotes}ground truth{close_quotes} are of primary importance in the development of retrieval algorithms using satellite measurements to predict surface irradiance. The most basic algorithms of this type deal with clear sky (i.e., cloudless) top-to-surface shortwave (SW) transfer, serving as a necessary prerequisite towards treating both clear and cloudy conditions. Recently, atmosphere SW cloud forcing to infer the possibility of excess atmospheric absorption (compared with model results) in cloudy atmospheres. The surface component of this ratio relies on inferring the expected clear sky SW irradiance to determine the effects of clouds on the SW energy budget. Solar renewable energy applications make use of clear and cloud fraction climatologies to assess solar radiation resources. All of the above depend to some extent on the identification of globally clear sky conditions and the attendant measurements of downwelling SW irradiance.

  4. Evaluation of Clear Sky Models for Satellite-Based Irradiance Estimates

    SciTech Connect

    Sengupta, M.; Gotseff, P.

    2013-12-01

    This report describes an intercomparison of three popular broadband clear sky solar irradiance model results with measured data, as well as satellite-based model clear sky results compared to measured clear sky data. The authors conclude that one of the popular clear sky models (the Bird clear sky model developed by Richard Bird and Roland Hulstrom) could serve as a more accurate replacement for current satellite-model clear sky estimations. Additionally, the analysis of the model results with respect to model input parameters indicates that rather than climatological, annual, or monthly mean input data, higher-time-resolution input parameters improve the general clear sky model performance.

  5. Monthly average clear-sky broadband irradiance database for worldwide solar heat gain and building cooling load calculations

    SciTech Connect

    Gueymard, Christian A.; Thevenard, Didier

    2009-11-15

    This paper establishes the formulation of a new clear-sky solar radiation model appropriate for algorithms calculating cooling loads in buildings. The aim is to replace the ASHRAE clear-sky model of 1967, whose limitations are well known and are reviewed. The new model is derived in two steps. The first step consists of obtaining a reference irradiance dataset from the REST2 model, which uses a high-performance, validated, two-band clear-sky algorithm. REST2 requires detailed inputs about atmospheric conditions such as aerosols, water vapor, ozone, and ground albedo. The development of global atmospheric datasets used as inputs to REST2 is reviewed. For the most part, these datasets are derived from space observations to guarantee universality and accuracy. In the case of aerosols, point-source terrestrial measurements were also used as ground truthing of the satellite data. The second step of the model consists of fits derived from a REST2-based reference irradiance dataset. These fits enable the derivation of compact, but relatively accurate expressions, for beam and diffuse clear-sky irradiance. The fitted expressions require the tabulation of only two pseudo-optical depths for each month of the year. The resulting model, and its tabulated data, are expected to be incorporated in the 2009 edition of the ASHRAE Handbook of Fundamentals. (author)

  6. DISCRIMINATING BETWEEN CLOUDY, HAZY, AND CLEAR SKY EXOPLANETS USING REFRACTION

    SciTech Connect

    Misra, Amit K.; Meadows, Victoria S.

    2014-11-01

    We propose a method to distinguish between cloudy, hazy, and clear sky (free of clouds and hazes) exoplanet atmospheres that could be applicable to upcoming large aperture space- and ground-based telescopes such as the James Webb Space Telescope (JWST) and the European Extremely Large Telescope (E-ELT). These facilities will be powerful tools for characterizing transiting exoplanets, but only after a considerable amount of telescope time is devoted to a single planet. A technique that could provide a relatively rapid means of identifying haze-free targets (which may be more valuable targets for characterization) could potentially increase the science return for these telescopes. Our proposed method utilizes broadband observations of refracted light in the out-of-transit spectrum. Light refracted through an exoplanet atmosphere can lead to an increase of flux prior to ingress and subsequent to egress. Because this light is transmitted at pressures greater than those for typical cloud and haze layers, the detection of refracted light could indicate a cloud- or haze-free atmosphere. A detection of refracted light could be accomplished in <10 hr for Jovian exoplanets with JWST and <5 hr for super-Earths/mini-Neptunes with E-ELT. We find that this technique is most effective for planets with equilibrium temperatures between 200 and 500K, which may include potentially habitable planets. A detection of refracted light for a potentially habitable planet would strongly suggest the planet was free of a global cloud or haze layer, and therefore a promising candidate for follow-up observations.

  7. Identification of periods of clear sky irradiance in time series of GHI measurements

    DOE PAGES [OSTI]

    Reno, Matthew J.; Hansen, Clifford W.

    2016-01-18

    In this study, we present a simple algorithm for identifying periods of time with broadband global horizontal irradiance (GHI) similar to that occurring during clear sky conditions from a time series of GHI measurements. Other available methods to identify these periods do so by identifying periods with clear sky conditions using additional measurements, such as direct or diffuse irradiance. Our algorithm compares characteristics of the time series of measured GHI with the output of a clear sky model without requiring additional measurements. We validate our algorithm using data from several locations by comparing our results with those obtained from amore » clear sky detection algorithm, and with satellite and ground-based sky imagery.« less

  8. ARM: Fractional cloud cover, clear-sky and all-sky shortwave flux for each of 25 individual SGP facilities.

    DOE Data Explorer

    Krista Gaustad; Laura Riihimaki

    1997-01-01

    Fractional cloud cover, clear-sky and all-sky shortwave flux for each of 25 individual SGP facilities.

  9. ARM: Fractional cloud cover, clear-sky and all-sky shortwave flux for each of 25 individual SGP facilities.

    DOE Data Explorer

    Krista Gaustad; Laura Riihimaki

    Fractional cloud cover, clear-sky and all-sky shortwave flux for each of 25 individual SGP facilities.

  10. Clear Skies

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    A. A. lacis NASA Goddard Space Flight Center Institute for Space Studies New York, NY 10025 "convective adjustment"takes place. Energy is transported upward within the troposphere and, in the process, the "critical lapse rate" of tropospheric temperature isestablished. Similarly, in response to the seasonally driven change in solar forcing, there is a latitudinal redistribution of energy by dynamical transports resulting in the meridional advection of energy. In view of the

  11. Performance characteristics of a perforated shadow band under clear sky conditions

    SciTech Connect

    Brooks, Michael J.

    2010-12-15

    A perforated, non-rotating shadow band is described for separating global solar irradiance into its diffuse and direct normal components using a single pyranometer. Whereas shadow bands are normally solid so as to occult the sensor of a pyranometer throughout the day, the proposed band has apertures cut from its circumference to intermittently expose the instrument sensor at preset intervals. Under clear sky conditions the device produces a saw tooth waveform of irradiance data from which it is possible to reconstruct separate global and diffuse curves. The direct normal irradiance may then be calculated giving a complete breakdown of the irradiance curves without need of a second instrument or rotating shadow band. This paper describes the principle of operation of the band and gives a mathematical model of its shading mask based on the results of an optical ray tracing study. An algorithm for processing the data from the perforated band system is described and evaluated. In an extended trial conducted at NREL's Solar Radiation Research Laboratory, the band coupled with a thermally corrected Eppley PSP produced independent curves for diffuse, global and direct normal irradiance with low mean bias errors of 5.6 W/m{sup 2}, 0.3 W/m{sup 2} and -2.6 W/m{sup 2} respectively, relative to collocated reference instruments. Random uncertainties were 9.7 W/m{sup 2} (diffuse), 17.3 W/m{sup 2} (global) and 19.0 W/m{sup 2} (direct). When the data processing algorithm was modified to include the ray trace model of sensor exposure, uncertainties increased only marginally, confirming the effectiveness of the model. Deployment of the perforated band system can potentially increase the accuracy of data from ground stations in predominantly sunny areas where instrumentation is limited to a single pyranometer. (author)

  12. Clear-sky and Cloudy Boundary Layers Virendra P. Ghate Argonne National Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Clear-sky and Cloudy Boundary Layers Virendra P. Ghate Argonne National Laboratory Define Boundary Layer Stull (1988) defined the atmospheric boundary layer as "the part of the troposphere that is directly influenced by the presence of the earth's surface, and responds to surface forcings with a time scale of about an hour or less." Typical Boundary Layer Depths and time-scales Scenario Time/Length scale Clear-air Convective 30 mins/1 km Cumulus Topped Boundary Layer 30 mins/1 km

  13. ARM: Gridded (0.25 x 0.25 lat/lon) fractional cloud cover, clear-sky and all-sky shortwave flux over the SGP site.

    DOE Data Explorer

    Krista Gaustad; Laura Riihimaki

    1997-01-01

    Gridded (0.25 x 0.25 lat/lon) fractional cloud cover, clear-sky and all-sky shortwave flux over the SGP site.

  14. ARM: Gridded (0.25 x 0.25 lat/lon) fractional cloud cover, clear-sky and all-sky shortwave flux over the SGP site.

    DOE Data Explorer

    Krista Gaustad; Laura Riihimaki

    Gridded (0.25 x 0.25 lat/lon) fractional cloud cover, clear-sky and all-sky shortwave flux over the SGP site.

  15. Analysis of S. 485, the Clear Skies Act of 2003, and S. 843, the Clean Air Planning Act of 2003

    Reports and Publications

    2003-01-01

    On July 30, 2003, Senator James M. Inhofe requested the Energy Information Administration to undertake analyses of S.843, The Clean Air Planning Act of 2003, introduced by Senator Thomas Carper, and S.485, Clear Skies Act of 2003. Senator Inhofe also asked the Energy Information Administration (EIA) to analyze S. 485 without the mercury provisions and S. 843 without the mercury and carbon dioxide provisions. This service report responds to both requests.

  16. Analysis of S. 1844, the Clear Skies Act of 2003; S. 843, the Clean Air Planning Act of 2003; and S. 366, the Clean Power Act of 2003

    Reports and Publications

    2004-01-01

    Senator James M. Inhofe requested that the Energy Information Administration (EIA) undertake analysis of S.843, the Clean Air Planning Act of 2003, introduced by Senator Thomas Carper; S.366, the Clean Power Act of 2003, introduced by Senator James Jeffords; and S.1844, the Clear Skies Act of 2003, introduced by Senator James M. Inhofe. The EIA received this request on March 19, 2004. This Service Report responds to his request.

  17. Clear Sky Detection Paper for Solar Energy

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ... Renewable Energy, 31, 1253-1263. Badescu, V., 1997. Verification of some very simple clear and cloudy sky models to evaluate global solar irradiance. Solar Energy, 61, 251-264. ...

  18. EIA model documentation: World oil refining logistics demand model,``WORLD`` reference manual. Version 1.1

    SciTech Connect

    Not Available

    1994-04-11

    This manual is intended primarily for use as a reference by analysts applying the WORLD model to regional studies. It also provides overview information on WORLD features of potential interest to managers and analysts. Broadly, the manual covers WORLD model features in progressively increasing detail. Section 2 provides an overview of the WORLD model, how it has evolved, what its design goals are, what it produces, and where it can be taken with further enhancements. Section 3 reviews model management covering data sources, managing over-optimization, calibration and seasonality, check-points for case construction and common errors. Section 4 describes in detail the WORLD system, including: data and program systems in overview; details of mainframe and PC program control and files;model generation, size management, debugging and error analysis; use with different optimizers; and reporting and results analysis. Section 5 provides a detailed description of every WORLD model data table, covering model controls, case and technology data. Section 6 goes into the details of WORLD matrix structure. It provides an overview, describes how regional definitions are controlled and defines the naming conventions for-all model rows, columns, right-hand sides, and bounds. It also includes a discussion of the formulation of product blending and specifications in WORLD. Several Appendices supplement the main sections.

  19. Rietveld Refinement

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    profile Chi-squared value 4.944 Progress so far Inverse Modeling Method 2 Fourier Method Data Model Refined Structure 40 60 80 100 120 140 160 0 1000 2000 3000 4000...

  20. Clear Skies S. A. Clough Atmospheric and Environmental Research, Inc.

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    S. A. Clough Atmospheric and Environmental Research, Inc. Cambridge, MA 02139 The objective of this research effort is to develop radiative transfer models that are consistent with Atmospheric Radiation Measurement (ARM) Program spectral radiance measurements for clear and cloudy atmospheres. Our approach is to develop the model physics and related databases with a line-by-line model in the context of available spectral radiance measurements. The line-by- line mode! then functions as an

  1. Shortwave Radiative Closure Studies for Clear Skies During the...

    Office of Scientific and Technical Information (OSTI)

    Plains (SGP) Climate Research Facility (CRF) in north central Oklahoma. Redundant measurements of aerosol optical properties were made using different techniques at the surface as ...

  2. Refiner Crude Oil Inputs

    Energy Information Administration (EIA) (indexed site)

    Net Inputs (Refiner and Blender) of RBOB Blending Components Net Inputs (Refiner and Blender) of CBOB Blending Components Net Inputs (Refiner and Blender) of GTAB Blending ...

  3. Crystal structure refinement with SHELXL

    SciTech Connect

    Sheldrick, George M., E-mail: gsheldr@shelx.uni-ac.gwdg.de [Department of Structural Chemistry, Georg-August Universitt Gttingen, Tammannstrae 4, Gttingen 37077 (Germany)

    2015-01-01

    New features added to the refinement program SHELXL since 2008 are described and explained. The improvements in the crystal structure refinement program SHELXL have been closely coupled with the development and increasing importance of the CIF (Crystallographic Information Framework) format for validating and archiving crystal structures. An important simplification is that now only one file in CIF format (for convenience, referred to simply as a CIF) containing embedded reflection data and SHELXL instructions is needed for a complete structure archive; the program SHREDCIF can be used to extract the .hkl and .ins files required for further refinement with SHELXL. Recent developments in SHELXL facilitate refinement against neutron diffraction data, the treatment of H atoms, the determination of absolute structure, the input of partial structure factors and the refinement of twinned and disordered structures. SHELXL is available free to academics for the Windows, Linux and Mac OS X operating systems, and is particularly suitable for multiple-core processors.

  4. ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Bandwidth for Petroleum Refining Processes ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes bandwidth.pdf (1.16 MB) More Documents & Publications ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes Bandwidth Study U.S. Petroleum Refining ITP Petroleum Refining: Energy and Environmental Profile of the U.S. Petroleum Refining Industry (November 2007) ITP Petroleum Refining: Profile of the Petroleum Refining Industry in

  5. Refines Efficiency Improvement

    SciTech Connect

    WRI

    2002-05-15

    Refinery processes that convert heavy oils to lighter distillate fuels require heating for distillation, hydrogen addition or carbon rejection (coking). Efficiency is limited by the formation of insoluble carbon-rich coke deposits. Heat exchangers and other refinery units must be shut down for mechanical coke removal, resulting in a significant loss of output and revenue. When a residuum is heated above the temperature at which pyrolysis occurs (340 C, 650 F), there is typically an induction period before coke formation begins (Magaril and Aksenova 1968, Wiehe 1993). To avoid fouling, refiners often stop heating a residuum before coke formation begins, using arbitrary criteria. In many cases, this heating is stopped sooner than need be, resulting in less than maximum product yield. Western Research Institute (WRI) has developed innovative Coking Index concepts (patent pending) which can be used for process control by refiners to heat residua to the threshold, but not beyond the point at which coke formation begins when petroleum residua materials are heated at pyrolysis temperatures (Schabron et al. 2001). The development of this universal predictor solves a long standing problem in petroleum refining. These Coking Indexes have great potential value in improving the efficiency of distillation processes. The Coking Indexes were found to apply to residua in a universal manner, and the theoretical basis for the indexes has been established (Schabron et al. 2001a, 2001b, 2001c). For the first time, a few simple measurements indicates how close undesired coke formation is on the coke formation induction time line. The Coking Indexes can lead to new process controls that can improve refinery distillation efficiency by several percentage points. Petroleum residua consist of an ordered continuum of solvated polar materials usually referred to as asphaltenes dispersed in a lower polarity solvent phase held together by intermediate polarity materials usually referred to as

  6. ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Bandwidth for Petroleum Refining Processes ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes bandwidth.pdf (1.16 MB) More Documents & Publications ITP ...

  7. ITP Petroleum Refining: Profile of the Petroleum Refining Industry...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Profile of the Petroleum Refining Industry in California: California Industries of the Future Program ITP Petroleum Refining: Profile of the Petroleum Refining Industry in ...

  8. Bandwidth Study U.S. Petroleum Refining | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Petroleum Refining Bandwidth Study U.S. Petroleum Refining Bandwidth Study U.S. Petroleum Refining Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. petroleum refining. The study relies on multiple sources to estimate the energy used in nine individual process areas,

  9. Step 3: Project Refinement

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3: Project Refinement 2 1 Potential 3 Refinement 4 Implementation 5 Operations & Maintenance 2 Options 3 Refinement 1/28/2016 2 3 FUNDING AND FINANCING OPTIONS Project Ownership Financing structure is highly dependent on size of the project and the capital available for a given project: * Tribe owns the project (cash purchase or debt) * Tribe hosts the project and buys the electricity (power purchase agreement) * Tribe partners with private sector and co-owns the project (uncertainties about

  10. Refiners trade hydroprocessing experience

    SciTech Connect

    Not Available

    1984-04-16

    Hydrogen treating and conversion processes less severe than hydrocracking abound in most refineries and therefore were a subject of high interest at the National Petroleum Refiners Association question and answer session on refining technology. The present paper, which is the second abstract of the transcript of the most recent meeting, covers hydroprocessing and some of its mechanical, process, and catalytic aspects.

  11. NAFTA opportunities: Petroleum refining

    SciTech Connect

    Not Available

    1993-01-01

    The North American Free Trade Agreement (NAFTA) creates a more transparent environment for the sale of refined petroleum products to Mexico, and locks in access to Canada's relatively open market for these products. Canada and Mexico are sizable United States export markets for refined petroleum products, with exports of $556 million and $864 million, respectively, in 1992. These markets represent approximately 24 percent of total U.S. exports of these goods.

  12. ITP Petroleum Refining: Profile of the Petroleum Refining Industry in

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    California: California Industries of the Future Program | Department of Energy Profile of the Petroleum Refining Industry in California: California Industries of the Future Program ITP Petroleum Refining: Profile of the Petroleum Refining Industry in California: California Industries of the Future Program cpi_profile.pdf (363.14 KB) More Documents & Publications ITP Petroleum Refining: Energy and Environmental Profile of the U.S. Petroleum Refining Industry (November 2007) ITP Petroleum

  13. Solvent Refined Coal (SRC) process: trace elements. Research and development report No. 53, interim report No. 30. Volume III. Pilot plant development work. Part 6. The fate of trace elements in the SRC process. [111 references

    SciTech Connect

    Khalil, S. R.

    1980-02-01

    Instrumental neutron activation analysis was used to study the distribution and fate of up to 36 elements in the Solvent Refined Coal Process Pilot Plant located at Fort Lewis, Washington. The elements Ti, V, Mg, Ca, Al, Cl, Mn, As, Br, Na, K, Sm, La, Ga, Cu, Sb, Se, Hg, Ni, Co, Cr, Fe, Rb, Cs, Sc, Tb, Eu, Ce, Sr, Ba, Th, U, Hf, Ta, Zr and Zn were measured in feed coal, insoluble residues, process solvent, process and effluent waters, by-product sulfur, SRC-I solid product, liquid-liquid separator oils and SRC-II liquid products. The material balance was calculated for each element from the concentration data and yields of each process fraction for both the SRC-I and SRC-II processes. Except for Ti, Cl and Br in the SRC-I mode and Hg in the SRC-II mode, each element was substantially lower in the SRC products than in the original feed coal. Residues from the process contained more than 80% of the trace element content found in the coal, except for Hg. More than 98.5% of the total contents of K and Fe in coal were retained in the insoluble residues. Elements such as Hg, Se, As and Sb can form volatile compounds (such as Hg/sup 0/, H/sub 2/Se, AsH/sub 3/ and SbH/sub 3/) stable under the process conditions. The high enhancement factors of Se (957), As (202) and Sb (27.4) in the aqueous phase of the separator water compared to that of the oil are evidence for the formation of volatile species which are more soluble in water than in the oil phase.

  14. Petroleum Refining | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Petroleum Refining Petroleum Refining Maintaining the viability of the U.S. petroleum refining industry requires continuous improvement in productivity and energy efficiency. The U.S. refining industry has worked with AMO to provide a range of resources that can provide energy and cost savings for the industry. Analytical Studies & Other Publications Manufacturing Energy and Carbon Footprints provide a mapping of energy use, energy loss, and carbon emissions for selected industry sectors.

  15. Clear Skies A Study of Longwave Radiation Codes for Climate Studies: Validation with Observations

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    A Study of Longwave Radiation Codes for Climate Studies: Validation with Observations and Tests in General Circulation Models-an Update R. G. Ellingson and F. Baer Department of Meteorology University of Maryland College Park, MD 20742 Introduction to compare calculations from a set of models with operationally observed data. The differences we find will lead to the development of new models to be tested with new data. Similarly. our GCM studies will use existing GCMs to study the radiation

  16. Use of Aeronet Aerosol Retrievals to Calculate Clear-Sky Irradiance...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    out of 300 Dobson Units of the total column ozone are located in the troposphere (Fishman et al. 1990), this is a reasonable approximation. Molecular extinction in the...

  17. Shortwave, Clear-sky Diffuse Irradiance in the 350 to 1050 nm...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    for the ET source function. The bottom figure includes differences caused by using the 5S and MODTRAN default ET spectra as opposed to the LOWTRAN default ET spectrum. This is...

  18. Sensitivity of Clear-Sky Diffuse Radiation to In Situ Aerosol...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ... L. G., and J. L. Greenstein, 1941: Diffuse radiation in the galaxy. Journal Astrophysics, 93, 70-83. Kato, S., T. P. Ackerman, E. G. Dutton, N. S. Laulainen, and N. Larson, 1997: A ...

  19. Clear Skies T. J. Kulp and J. Shinn Geophysics and Environmental...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ... cell through the MB1 00 sample area and onto its detector using a set of plane mirrors. ... Note the line spectra and the underlying continuum. The scan near zero absorbance is a ...

  20. Minimally refined biomass fuel

    DOEpatents

    Pearson, Richard K.; Hirschfeld, Tomas B.

    1984-01-01

    A minimally refined fluid composition, suitable as a fuel mixture and derived from biomass material, is comprised of one or more water-soluble carbohydrates such as sucrose, one or more alcohols having less than four carbons, and water. The carbohydrate provides the fuel source; water solubilizes the carbohydrates; and the alcohol aids in the combustion of the carbohydrate and reduces the vicosity of the carbohydrate/water solution. Because less energy is required to obtain the carbohydrate from the raw biomass than alcohol, an overall energy savings is realized compared to fuels employing alcohol as the primary fuel.

  1. CLAMR (Compute Language Adaptive Mesh Refinement)

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    CLAMR (Compute Language Adaptive Mesh Refinement) CLAMR (Compute Language Adaptive Mesh Refinement) CLAMR (Compute Language Adaptive Mesh Refinement) is being developed as a DOE...

  2. ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Bandwidth for Petroleum Refining Processes Prepared by Energetics Incorporated for the U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Industrial ...

  3. Midcourse Refinements of Financing Strategies

    Energy.gov [DOE]

    Better Buildings Neighborhood Program Financing Peer Exchange Call: Midcourse Refinements of Financing Strategies, Call Slides and Discussion Summary, March 29, 2012. During this webinar participants discussed how programs have adapted and refined their financing strategies based on initial implementation experience and learning.

  4. Parallel Adaptive Mesh Refinement

    SciTech Connect

    Diachin, L; Hornung, R; Plassmann, P; WIssink, A

    2005-03-04

    As large-scale, parallel computers have become more widely available and numerical models and algorithms have advanced, the range of physical phenomena that can be simulated has expanded dramatically. Many important science and engineering problems exhibit solutions with localized behavior where highly-detailed salient features or large gradients appear in certain regions which are separated by much larger regions where the solution is smooth. Examples include chemically-reacting flows with radiative heat transfer, high Reynolds number flows interacting with solid objects, and combustion problems where the flame front is essentially a two-dimensional sheet occupying a small part of a three-dimensional domain. Modeling such problems numerically requires approximating the governing partial differential equations on a discrete domain, or grid. Grid spacing is an important factor in determining the accuracy and cost of a computation. A fine grid may be needed to resolve key local features while a much coarser grid may suffice elsewhere. Employing a fine grid everywhere may be inefficient at best and, at worst, may make an adequately resolved simulation impractical. Moreover, the location and resolution of fine grid required for an accurate solution is a dynamic property of a problem's transient features and may not be known a priori. Adaptive mesh refinement (AMR) is a technique that can be used with both structured and unstructured meshes to adjust local grid spacing dynamically to capture solution features with an appropriate degree of resolution. Thus, computational resources can be focused where and when they are needed most to efficiently achieve an accurate solution without incurring the cost of a globally-fine grid. Figure 1.1 shows two example computations using AMR; on the left is a structured mesh calculation of a impulsively-sheared contact surface and on the right is the fuselage and volume discretization of an RAH-66 Comanche helicopter [35]. Note the

  5. MECS 2006 - Petroleum Refining | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Petroleum Refining MECS 2006 - Petroleum Refining Manufacturing Energy and Carbon Footprint for Petroleum Refining (NAICS 324110) Sector with Total Energy Input, October 2012 (MECS 2006) All available footprints and supporting documents Manufacturing Energy and Carbon Footprint Petroleum Refining (123.98 KB) More Documents & Publications Petroleum Refining (2010 MECS) MECS 2006 - Alumina and Aluminum MECS 2006 - Cement

  6. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for Biological and Environmental Research May 7-8, 2009 Invitation Workshop Invitation Letter...

  7. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for Basic Energy Sciences February 9-10, 2010 Official DOE Invitation Workshop Invitation...

  8. Electronic structure of superconductivity refined

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Electronic structure of superconductivity refined Electronic structure of superconductivity refined A team of physicists propose a new model that expands on a little understood aspect of the electronic structure in high-temperature superconductors. July 10, 2008 Los Alamos National Laboratory sits on top of a once-remote mesa in northern New Mexico with the Jemez mountains as a backdrop to research and innovation covering multi-disciplines from bioscience, sustainable energy sources, to plasma

  9. Pollution prevention in the petroleum refining industry

    SciTech Connect

    Fromm, C.H.; White, S.L.

    1995-09-01

    Pollution prevention (P2) as applied to petroleum refining should seek opportunities to reduce waste by preventing oil/hydrocarbon loss, by decreasing consumption of auxiliary input materials, and by improving conversion of incoming impurities into useful products. This chapter will focus on P2 techniques that have found or could find applications in minimizing or eliminating reducible solid waste and wastewater from the petroleum refining process. Air emissions are not covered. The following commonly encountered wastes are considered in this chapter: oily sludges; spent caustics; spent catalysts; miscellaneous process wastes; wastewater; maintenance and materials handling wastes. Following a brief description of waste components and sources, specific P2 techniques are presented in tabular form for each of these wastestreams. None of the P2 techniques presented is discussed here in any detail--the intent is to give the reader a menu of potentially effective P2 options to consider, along with the references where a more detailed discussion may be found. Some of the options presented were advanced in the original references merely as suggestions or plans for improvement. No effort was made to verify their efficacy or applicability in this compilation.

  10. Renewable Energy Financial Instruments Guidance Tool (REFINe...

    OpenEI (Open Energy Information) [EERE & EIA]

    Guidance Tool (REFINe) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Renewable Energy Financial Instruments Guidance Tool (REFINe) Focus Area: Renewable Energy...

  11. ,"U.S. Refiner Petroleum Product Prices"

    Energy Information Administration (EIA) (indexed site)

    ...AEPPRLPTGNUSDPG","EMAEPPRHPTGNUSDPG" "Date","U.S. Total Gasoline Retail Sales by Refiners (Dollars per Gallon)","U.S. Aviation Gasoline Retail Sales by Refiners (Dollars ...

  12. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for Basic Energy Sciences February 9-10, 2010 Official DOE Invitation Workshop Invitation Letter from DOE Associate Directors Last edited: 2016-04-29 11:35:05

  13. Petroleum Refining (2010 MECS) | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Petroleum Refining (2010 MECS) Petroleum Refining (2010 MECS) Manufacturing Energy and Carbon Footprint for Petroleum Refining Sector (NAICS 324110) Energy use data source: 2010 EIA MECS (with adjustments) Footprint Last Revised: February 2014 View footprints for other sectors here. Manufacturing Energy and Carbon Footprint Petroleum Refining (125.36 KB) More Documents & Publications MECS 2006 - Petroleum Refining Cement (2010 MECS) Forest Products (2010 MECS) Manufacturing Energy Sankey

  14. GRAIN REFINEMENT OF URANIUM BILLETS

    DOEpatents

    Lewis, L.

    1964-02-25

    A method of refining the grain structure of massive uranium billets without resort to forging is described. The method consists in the steps of beta- quenching the billets, annealing the quenched billets in the upper alpha temperature range, and extrusion upset of the billets to an extent sufficient to increase the cross sectional area by at least 5 per cent. (AEC)

  15. Method for refining contaminated iridium

    DOEpatents

    Heshmatpour, B.; Heestand, R.L.

    1982-08-31

    Contaminated iridium is refined by alloying it with an alloying agent selected from the group consisting of manganese and an alloy of manganese and copper, and then dissolving the alloying agent from the formed alloy to provide a purified iridium powder.

  16. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials (continued) * Generators are required to avoid Las Vegas metropolitan area and Hoover Dam (Section 6.4 of NNSS Waste Acceptance Criteria, available at ...

  17. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for Advanced Scientific Computing Research January 5-6, 2011 Official DOE Invitation Workshop Invitation Letter from DOE Associate Directors NERSC Documents NERSC science requirements home page NERSC science requirements workshop page NERSC science requirements case study FAQ Previous NERSC Requirements Workshops Biological and Environmental Research (BER) Basic Energy Sciences (BES) Fusion Energy Sciences

  18. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for Biological and Environmental Research May 7-8, 2009 Invitation Workshop Invitation Letter from DOE Associate Directors Workshop Invitation Letter from DOE ASCR Program Manager Yukiko Sekine Last edited: 2016-04-29 11:34:54

  19. Reformulated Gasoline Market Affected Refiners Differently, 1995

    Reports and Publications

    1996-01-01

    This article focuses on the costs of producing reformulated gasoline (RFG) as experienced by different types of refiners and on how these refiners fared this past summer, given the prices for RFG at the refinery gate.

  20. Quick Reference

    Energy.gov [DOE] (indexed site)

    Reference 2015 Annual Planning Summary (APS) User's Guide 1, 2 PART 1 OFFICE Enter the office preparing this APS. NEPA REVIEWS Select one of two responses. SITE-WIDE EISs Select...

  1. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for Fusion Energy Sciences August 3-4, 2010 Official DOE Invitation Workshop Invitation Letter from DOE Associate Directors [not available] NERSC Documents NERSC science requirements home page NERSC science requirements workshop page NERSC science requirements case study FAQ Workshop Agenda Previous NERSC Requirements Workshops Biological and Environmental Research (BER) Basic Energy Sciences (BES) Fusion

  2. Reference Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Reference Materials Reference Materials Large Scale Computing and Storage Requirements for High Energy Physics November 12-13, 2009 Official DOE Invitation Workshop Invitation Letter from DOE Associate Directors NERSC Documents NERSC science requirements home page NERSC science requirements workshop page NERSC science requirements case study FAQ Workshop Agenda Previous NERSC Requirements Workshops Biological and Environmental Research (BER) Basic Energy Sciences (BES) Fusion Energy Sciences

  3. Firing of pulverized solvent refined coal

    DOEpatents

    Derbidge, T. Craig; Mulholland, James A.; Foster, Edward P.

    1986-01-01

    An air-purged burner for the firing of pulverized solvent refined coal is constructed and operated such that the solvent refined coal can be fired without the coking thereof on the burner components. The air-purged burner is designed for the firing of pulverized solvent refined coal in a tangentially fired boiler.

  4. ITP Petroleum Refining: Energy and Environmental Profile of the...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    and Environmental Profile of the U.S. Petroleum Refining Industry (November 2007) ITP Petroleum Refining: Energy and Environmental Profile of the U.S. Petroleum Refining Industry ...

  5. Poroelastic references

    DOE Data Explorer

    Christina Morency

    This file contains a list of relevant references on the Biot theory (forward and inverse approaches), the double-porosity and dual-permeability theory, and seismic wave propagation in fracture porous media, in RIS format, to approach seismic monitoring in a complex fractured porous medium such as Brady?s Geothermal Field.

  6. Poroelastic references

    SciTech Connect

    Morency, Christina

    2014-12-12

    This file contains a list of relevant references on the Biot theory (forward and inverse approaches), the double-porosity and dual-permeability theory, and seismic wave propagation in fracture porous media, in RIS format, to approach seismic monitoring in a complex fractured porous medium such as Brady?s Geothermal Field.

  7. Improving the accuracy of macromolecular structure refinement

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    is challenging at low resolution. We compared refinement methods using synchrotron diffraction data of photosystem I at 7.4 resolution, starting from different initial models...

  8. Refiners Increasingly Employing Catalyst Regeneration as Alternative...

    OpenEI (Open Energy Information) [EERE & EIA]

    million by the end of 2019. Refiners Benefit from Catalyst Regeneration Technology via Price Reductions and Lower Maintenance Costs The catalyst regeneration technology is the...

  9. Right rock: Finding/refining customer expectations

    SciTech Connect

    Ashby, R.

    1997-11-01

    This report contains viewgraphs on methods of finding customer expectations of software and then refining the documentation and software to fit these expectations.

  10. Midcourse Refinements of Financing Strategies | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    March 29, 2012. During this webinar participants discussed how programs have adapted and refined their financing strategies based on initial implementation experience and learning. ...

  11. Pneumatic conveying of pulverized solvent refined coal

    DOEpatents

    Lennon, Dennis R.

    1984-11-06

    A method for pneumatically conveying solvent refined coal to a burner under conditions of dilute phase pneumatic flow so as to prevent saltation of the solvent refined coal in the transport line by maintaining the transport fluid velocity above approximately 95 ft/sec.

  12. North Dakota Refining Capacity Study

    SciTech Connect

    Dennis Hill; Kurt Swenson; Carl Tuura; Jim Simon; Robert Vermette; Gilberto Marcha; Steve Kelly; David Wells; Ed Palmer; Kuo Yu; Tram Nguyen; Juliam Migliavacca

    2011-01-05

    According to a 2008 report issued by the United States Geological Survey, North Dakota and Montana have an estimated 3.0 to 4.3 billion barrels of undiscovered, technically recoverable oil in an area known as the Bakken Formation. With the size and remoteness of the discovery, the question became 'can a business case be made for increasing refining capacity in North Dakota?' And, if so what is the impact to existing players in the region. To answer the question, a study committee comprised of leaders in the region's petroleum industry were brought together to define the scope of the study, hire a consulting firm and oversee the study. The study committee met frequently to provide input on the findings and modify the course of the study, as needed. The study concluded that the Petroleum Area Defense District II (PADD II) has an oversupply of gasoline. With that in mind, a niche market, naphtha, was identified. Naphtha is used as a diluent used for pipelining the bitumen (heavy crude) from Canada to crude markets. The study predicted there will continue to be an increase in the demand for naphtha through 2030. The study estimated the optimal configuration for the refinery at 34,000 barrels per day (BPD) producing 15,000 BPD of naphtha and a 52 percent refinery charge for jet and diesel yield. The financial modeling assumed the sponsor of a refinery would invest its own capital to pay for construction costs. With this assumption, the internal rate of return is 9.2 percent which is not sufficient to attract traditional investment given the risk factor of the project. With that in mind, those interested in pursuing this niche market will need to identify incentives to improve the rate of return.

  13. Firing of pulverized solvent refined coal

    DOEpatents

    Lennon, Dennis R.; Snedden, Richard B.; Foster, Edward P.; Bellas, George T.

    1990-05-15

    A burner for the firing of pulverized solvent refined coal is constructed and operated such that the solvent refined coal can be fired successfully without any performance limitations and without the coking of the solvent refined coal on the burner components. The burner is provided with a tangential inlet of primary air and pulverized fuel, a vaned diffusion swirler for the mixture of primary air and fuel, a center water-cooled conical diffuser shielding the incoming fuel from the heat radiation from the flame and deflecting the primary air and fuel steam into the secondary air, and a watercooled annulus located between the primary air and secondary air flows.

  14. U.S. Refining Capacity Utilization

    Reports and Publications

    1995-01-01

    This article briefly reviews recent trends in domestic refining capacity utilization and examines in detail the differences in reported crude oil distillation capacities and utilization rates among different classes of refineries.

  15. Hydrogen Piping Experience in Chevron Refining

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Piping Experience in Chevron Refining Ned Niccolls Materials Engineer Chevron Energy Technology Company Hydrogen Pipeline Working Group Workshop August 30-31, 2005 Outline 2 Overall perspectives from long term use of hydrogen piping in refining. Piping specifications and practices. The (few) problem areas. Related industry work: American Petroleum Institute corrosion and materials work on high temperature hydrogen attack. Overall Perspectives 3 Few problems with hydrogen piping operating at

  16. Refining Bio-Oil alongside Petroleum | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Refining Bio-Oil alongside Petroleum Refining Bio-Oil alongside Petroleum April 9, 2013 - 12:00am Addthis W.R. Grace, a leading provider of refining technologies, and Pacific ...

  17. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Motor Gasoline No. 2 Distillate Residual Fuel Oil 5. U.S. Refiner Wholesale Petroleum Product Volumes Figure Percentages of Refiner Wholesale Volumes 1995 Annual Averages Motor...

  18. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Day Motor Gasoline No. 2 Distillate Residual Fuel Oil 3. U.S. Refiner Retail Petroleum Product Volumes Figure Percentages of Refiner Retail Volumes 1997 Annual Averages Motor...

  19. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Motor Gasoline No. 2 Distillate Residual Fuel Oil 5. U.S. Refiner Wholesale Petroleum Product Volumes Figure Percentages of Refiner Wholesale Volumes 1997 Annual Averages Motor...

  20. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Day Motor Gasoline No. 2 Distillate Residual Fuel Oil 3. U.S. Refiner Retail Petroleum Product Volumes Figure Percentages of Refiner Retail Volumes 1995 Annual Averages Motor...

  1. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Day Motor Gasoline No. 2 Distillate Residual Fuel Oil 3. U.S. Refiner Retail Petroleum Product Volumes Figure Percentages of Refiner Retail Volumes 1996 Annual Averages Motor...

  2. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Motor Gasoline No. 2 Distillate Residual Fuel Oil 5. U.S. Refiner Wholesale Petroleum Product Volumes Figure Percentages of Refiner Wholesale Volumes 1996 Annual Averages Motor...

  3. ,"Aviation Gasoline Sales to End Users Refiner Sales Volumes...

    Energy Information Administration (EIA) (indexed site)

    Aviation Gasoline Sales to End Users Refiner Sales Volumes" ,"Click worksheet name or tab ... Data for" ,"Data 1","Aviation Gasoline Sales to End Users Refiner ...

  4. ,"U.S. Motor Gasoline Refiner Sales Volumes"

    Energy Information Administration (EIA) (indexed site)

    Data for" ,"Data 1","U.S. Motor Gasoline Refiner Sales ... AM" "Back to Contents","Data 1: U.S. Motor Gasoline Refiner Sales Volumes" ...

  5. ITP Petroleum Refining: Impacts of Condition Assessment on Energy...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining ITP Petroleum Refining: Impacts of Condition Assessment on ...

  6. Parallel tetrahedral mesh refinement with MOAB.

    SciTech Connect

    Thompson, David C.; Pebay, Philippe Pierre

    2008-12-01

    In this report, we present the novel functionality of parallel tetrahedral mesh refinement which we have implemented in MOAB. This report details work done to implement parallel, edge-based, tetrahedral refinement into MOAB. The theoretical basis for this work is contained in [PT04, PT05, TP06] while information on design, performance, and operation specific to MOAB are contained herein. As MOAB is intended mainly for use in pre-processing and simulation (as opposed to the post-processing bent of previous papers), the primary use case is different: rather than refining elements with non-linear basis functions, the goal is to increase the number of degrees of freedom in some region in order to more accurately represent the solution to some system of equations that cannot be solved analytically. Also, MOAB has a unique mesh representation which impacts the algorithm. This introduction contains a brief review of streaming edge-based tetrahedral refinement. The remainder of the report is broken into three sections: design and implementation, performance, and conclusions. Appendix A contains instructions for end users (simulation authors) on how to employ the refiner.

  7. Trends in petroleum refining process technology

    SciTech Connect

    Kowalczyk, D.

    1995-12-31

    In the 1990`s, the shift toward reformulated fuels and the unrelenting economic pressures on the petroleum refining industry have led to the ongoing development of a series of technological advances to improve fuels quality and industry operating efficiency. In this paper, ten of the most innovative and high impact recent developments in petroleum refining process technology will be highlighted. Process improvements and innovations have occurred in all facets of petroleum refining operations including fluid catalytic cracking, ether production, desulfurization, hydrocracking, gas processing, environmental control and heavy oil processing. Discussed will be the technical and economic impact of each of these new technologies on the petroleum refinery of the late 20th and early 21st century.

  8. JAPAN: Refining options and liberalization plans

    SciTech Connect

    Totto, L.; Isaak, D.T.

    1988-01-01

    The reformulation of Japan's petroleum import policy is important to Japan and to the international energy community. The technical and economic factors involved in opening the Japanese market is unknown. Assuming that foreign refiners have the technical capability to meet Japanese product specifications, the prices and volumes that will prove economical to both parties are also little known. Japanese refiners have been investigating the possibility of exporting gasoline and processing crude for China and Malaysia. The study demonstrates that under certain trade policies, Japan could become a significant product exporter. This study's purpose is to investigate the economic efficiency of alternative petroleum supply options, i.e., combining Japan's refining and product imports. An evaluation of the current import program and the technically feasible alternatives will play a major role in a new import policy. For this evaluation, a linear programming (LP) model of Japan's domestic refinery capacity and the petroleum import system was constructed. 3 figs., 23 tabs.

  9. The strategic outlook for petroleum refiners

    SciTech Connect

    Cobb, C.

    1994-12-31

    After several years of acceptable and relatively reliable profitability, refiners were plunged into uncertainty once again following passage of the Clean Air Act Amendments (CAAA) in 1990. While many of the original uncertainties that attended these regulations have since been resolved, the industry now must prepare for the new manufacturing, distributions, and transportation challenges that undoubtedly will accompany the first stages of reformulated gasoline (RFG) compliance in early 1995. This impending challenge introduces several fundamental questions: (1) How has the industry changed and adjusted to respond to anticipated future needs? (2) What strategies are refiners employing today? (3) What are industry performance expectations over the next several years?

  10. Using supercritical fluids to refine hydrocarbons

    DOEpatents

    Yarbro, Stephen Lee

    2015-06-09

    A system and method for reactively refining hydrocarbons, such as heavy oils with API gravities of less than 20 degrees and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure, using a selected fluid at supercritical conditions. A reaction portion of the system and method delivers lightweight, volatile hydrocarbons to an associated contacting unit which operates in mixed subcritical/supercritical or supercritical modes. Using thermal diffusion, multiphase contact, or a momentum generating pressure gradient, the contacting unit separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques.

  11. Arbitrary Lagrangian Eulerian Adaptive Mesh Refinement

    Energy Science and Technology Software Center

    2009-09-29

    This is a simulation code involving an ALE (arbitrary Lagrangian-Eulerian) hydrocode with AMR (adaptive mesh refinement) and pluggable physics packages for material strength, heat conduction, radiation diffusion, and laser ray tracing developed a LLNL, UCSD, and Berkeley Lab. The code is an extension of the open source SAMRAI (Structured Adaptive Mesh Refinement Application Interface) code/library. The code can be used in laser facilities such as the National Ignition Facility. The code is alsi being appliedmore » to slurry flow (landslides).« less

  12. ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum Refineries

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    in California | Department of Energy Energy Efficiency Roadmap for Petroleum Refineries in California ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum Refineries in California refining_roadmap.pdf (1.34 MB) More Documents & Publications ITP Petroleum Refining: Profile of the Petroleum Refining Industry in California: California Industries of the Future Program ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum Refineries in California Bandwidth Study U.S.

  13. Energy Bandwidth for Petroleum Refining Processes

    SciTech Connect

    none,

    2006-10-01

    The petroleum refining energy bandwidth report analyzes the most energy-intensive unit operations used in U.S. refineries: crude oil distillation, fluid catalytic cracking, catalytic hydrotreating, catalytic reforming, and alkylation. The "bandwidth" provides a snapshot of the energy losses that can potentially be recovered through best practices and technology R&D.

  14. Focus on Venezuelan heavy crude: refining margins

    SciTech Connect

    Not Available

    1984-01-25

    Of six crudes refined in the US Gulf Coast, heavy Venezuelan crude Lagunillas (15/sup 0/ API) provides the best margin per barrel. Data for end of December 1983 and the first three weeks of January show that margins on all crudes are on the rise in this market, due to a turnaround in product prices. The lighter crudes are showing the greatest increase in Gross Product Worth. This is having a modest shrinking effect on the margin differential between light and heavy crudes in this market. The domestic crude West Texas Intermediate, at 40/sup 0/ API, provides the highest GPW in this crude slate sample, over US $31 per barrel, compared to GPW of under US $28 per barrel for Lagunillas. Still, as Lagunillas cost about US $8 less than does WTI, refiners with sufficient residue conversion capacity can be earning about US $3.50 more in margin per barrel than they can with WTI. Although few refiners would be using a 15/sup 0/ API crude exclusively for any length of time, heavier oil's inclusion in modern refiners' diets is enhancing their competitive position more than any other single factor. This issue of Energy Detente presents the fuel price/tax series and industrial fuel prices for January 1984 for countries of the Western Hemisphere.

  15. Metal decontamination for waste minimization using liquid metal refining technology

    SciTech Connect

    Joyce, E.L. Jr.; Lally, B.; Ozturk, B.; Fruehan, R.J.

    1993-09-01

    The current Department of Energy Mixed Waste Treatment Project flowsheet indicates that no conventional technology, other than surface decontamination, exists for metal processing. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain concentration. This project is in support of the National Mixed Low Level Waste Treatment Program. Because of the high cost of disposal, it is important to develop an effective decontamination and volume reduction method for low-level contaminated metals. It is important to be able to decontaminate complex shapes where surfaces are hidden or inaccessible to surface decontamination processes and destruction of organic contamination. These goals can be achieved by adapting commercial metal refining processes to handle radioactive and organic contaminated metal. The radioactive components are concentrated in the slag, which is subsequently vitrified; hazardous organics are destroyed by the intense heat of the bath. The metal, after having been melted and purified, could be recycled for use within the DOE complex. In this project, we evaluated current state-of-the-art technologies for metal refining, with special reference to the removal of radioactive contaminants and the destruction of hazardous organics. This evaluation was based on literature reports, industrial experience, plant visits, thermodynamic calculations, and engineering aspects of the various processes. The key issues addressed included radioactive partitioning between the metal and slag phases, minimization of secondary wastes, operability of the process subject to widely varying feed chemistry, and the ability to seal the candidate process to prevent the release of hazardous species.

  16. Using supercritical fluids to refine hydrocarbons

    DOEpatents

    Yarbro, Stephen Lee

    2014-11-25

    This is a method to reactively refine hydrocarbons, such as heavy oils with API gravities of less than 20.degree. and bitumen-like hydrocarbons with viscosities greater than 1000 cp at standard temperature and pressure using a selected fluid at supercritical conditions. The reaction portion of the method delivers lighter weight, more volatile hydrocarbons to an attached contacting device that operates in mixed subcritical or supercritical modes. This separates the reaction products into portions that are viable for use or sale without further conventional refining and hydro-processing techniques. This method produces valuable products with fewer processing steps, lower costs, increased worker safety due to less processing and handling, allow greater opportunity for new oil field development and subsequent positive economic impact, reduce related carbon dioxide, and wastes typical with conventional refineries.

  17. Refining quadrilateral and brick element meshes

    SciTech Connect

    Schneiders, R.; Debye, J.

    1995-12-31

    We consider the problem of refining unstructured quadrilateral and brick element meshes. We present an algorithm which is a generalization of an algorithm developed by Cheng et. al. for structured quadrilateral element meshes. The problem is solved for the two-dimensional case. Concerning three dimensions we present a solution for some special cases and a general solution that introduces tetrahedral and pyramidal transition elements.

  18. Structured Adaptive Mesh Refinement Application Infrastructure

    Energy Science and Technology Software Center

    2010-07-15

    SAMRAI is an object-oriented support library for structured adaptice mesh refinement (SAMR) simulation of computational science problems, modeled by systems of partial differential equations (PDEs). SAMRAI is developed and maintained in the Center for Applied Scientific Computing (CASC) under ASCI ITS and PSE support. SAMRAI is used in a variety of application research efforts at LLNL and in academia. These applications are developed in collaboration with SAMRAI development team members.

  19. Genealogy of major U.S. refiners - Energy Information Administration

    Energy Information Administration (EIA) (indexed site)

    Genealogy of Major U.S. Refiners Release date: September 18, 2013 figre 1. World energy consumption, 1990-2040. The structure of the U.S. petroleum refining industry has changed ...

  20. ,"Residual Fuel Oil Sales to End Users Refiner Sales Volumes...

    Energy Information Administration (EIA) (indexed site)

    Data for" ,"Data 1","Residual Fuel Oil Sales to End Users Refiner Sales ... "Back to Contents","Data 1: Residual Fuel Oil Sales to End Users Refiner Sales Volumes" ...

  1. Grain Refinement of Permanent Mold Cast Copper Base Alloys

    SciTech Connect

    M.Sadayappan; J.P.Thomson; M.Elboujdaini; G.Ping Gu; M. Sahoo

    2005-04-01

    Grain refinement is a well established process for many cast and wrought alloys. The mechanical properties of various alloys could be enhanced by reducing the grain size. Refinement is also known to improve casting characteristics such as fluidity and hot tearing. Grain refinement of copper-base alloys is not widely used, especially in sand casting process. However, in permanent mold casting of copper alloys it is now common to use grain refinement to counteract the problem of severe hot tearing which also improves the pressure tightness of plumbing components. The mechanism of grain refinement in copper-base alloys is not well understood. The issues to be studied include the effect of minor alloy additions on the microstructure, their interaction with the grain refiner, effect of cooling rate, and loss of grain refinement (fading). In this investigation, efforts were made to explore and understand grain refinement of copper alloys, especially in permanent mold casting conditions.

  2. ITP Petroleum Refining: Impacts of Condition Assessment on Energy Use:

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Selected Applications in Chemicals Processing and Petroleum Refining | Department of Energy Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining ITP Petroleum Refining: Impacts of Condition Assessment on Energy Use: Selected Applications in Chemicals Processing and Petroleum Refining condition_assessment.pdf (319.56 KB) More Documents & Publications Effective Fouling Minimization Increases the Efficiency and Productivity of

  3. Reference Inflow Characterization for River Resource Reference Model (RM2)

    SciTech Connect

    Neary, Vincent S

    2011-12-01

    Sandia National Laboratory (SNL) is leading an effort to develop reference models for marine and hydrokinetic technologies and wave and current energy resources. This effort will allow the refinement of technology design tools, accurate estimates of a baseline levelized cost of energy (LCoE), and the identification of the main cost drivers that need to be addressed to achieve a competitive LCoE. As part of this effort, Oak Ridge National Laboratory was charged with examining and reporting reference river inflow characteristics for reference model 2 (RM2). Published turbulent flow data from large rivers, a water supply canal and laboratory flumes, are reviewed to determine the range of velocities, turbulence intensities and turbulent stresses acting on hydrokinetic technologies, and also to evaluate the validity of classical models that describe the depth variation of the time-mean velocity and turbulent normal Reynolds stresses. The classical models are found to generally perform well in describing river inflow characteristics. A potential challenge in river inflow characterization, however, is the high variability of depth and flow over the design life of a hydrokinetic device. This variation can have significant effects on the inflow mean velocity and turbulence intensity experienced by stationary and bottom mounted hydrokinetic energy conversion devices, which requires further investigation, but are expected to have minimal effects on surface mounted devices like the vertical axis turbine device designed for RM2. A simple methodology for obtaining an approximate inflow characterization for surface deployed devices is developed using the relation umax=(7/6)V where V is the bulk velocity and umax is assumed to be the near-surface velocity. The application of this expression is recommended for deriving the local inflow velocity acting on the energy extraction planes of the RM2 vertical axis rotors, where V=Q/A can be calculated given a USGS gage flow time

  4. Deformable elastic network refinement for low-resolution macromolecular crystallography

    SciTech Connect

    Schröder, Gunnar F.; Levitt, Michael; Brunger, Axel T.

    2014-09-01

    An overview of applications of the deformable elastic network (DEN) refinement method is presented together with recommendations for its optimal usage. Crystals of membrane proteins and protein complexes often diffract to low resolution owing to their intrinsic molecular flexibility, heterogeneity or the mosaic spread of micro-domains. At low resolution, the building and refinement of atomic models is a more challenging task. The deformable elastic network (DEN) refinement method developed previously has been instrumental in the determinion of several structures at low resolution. Here, DEN refinement is reviewed, recommendations for its optimal usage are provided and its limitations are discussed. Representative examples of the application of DEN refinement to challenging cases of refinement at low resolution are presented. These cases include soluble as well as membrane proteins determined at limiting resolutions ranging from 3 to 7 Å. Potential extensions of the DEN refinement technique and future perspectives for the interpretation of low-resolution crystal structures are also discussed.

  5. Unmanned Aerospace Vehicle Workshop

    SciTech Connect

    Vitko, J. Jr.

    1995-04-01

    The Unmanned Aerospace Vehicle (UAV) Workshop concentrated on reviewing and refining the science experiments planned for the UAV Demonstration Flights (UDF) scheduled at the Oklahoma Cloud and Radiation Testbed (CART) in April 1994. These experiments were focused around the following sets of parameters: Clear sky, daylight; Clear-sky, night-to-day transition; Clear sky - improve/validate the accuracy of radiative fluxes derived from satellite-based measurements; Daylight, clouds of opportunity; and, Daylight, broken clouds.

  6. Tools for macromolecular model building and refinement into electron cryo-microscopy reconstructions

    SciTech Connect

    Brown, Alan; Long, Fei; Nicholls, Robert A.; Toots, Jaan; Emsley, Paul; Murshudov, Garib

    2015-01-01

    A description is given of new tools to facilitate model building and refinement into electron cryo-microscopy reconstructions. The recent rapid development of single-particle electron cryo-microscopy (cryo-EM) now allows structures to be solved by this method at resolutions close to 3 Å. Here, a number of tools to facilitate the interpretation of EM reconstructions with stereochemically reasonable all-atom models are described. The BALBES database has been repurposed as a tool for identifying protein folds from density maps. Modifications to Coot, including new Jiggle Fit and morphing tools and improved handling of nucleic acids, enhance its functionality for interpreting EM maps. REFMAC has been modified for optimal fitting of atomic models into EM maps. As external structural information can enhance the reliability of the derived atomic models, stabilize refinement and reduce overfitting, ProSMART has been extended to generate interatomic distance restraints from nucleic acid reference structures, and a new tool, LIBG, has been developed to generate nucleic acid base-pair and parallel-plane restraints. Furthermore, restraint generation has been integrated with visualization and editing in Coot, and these restraints have been applied to both real-space refinement in Coot and reciprocal-space refinement in REFMAC.

  7. COSMOLOGICAL ADAPTIVE MESH REFINEMENT MAGNETOHYDRODYNAMICS WITH ENZO

    SciTech Connect

    Collins, David C.; Xu Hao; Norman, Michael L.; Li Hui; Li Shengtai

    2010-02-01

    In this work, we present EnzoMHD, the extension of the cosmological code Enzo to include the effects of magnetic fields through the ideal magnetohydrodynamics approximation. We use a higher order Godunov method for the computation of interface fluxes. We use two constrained transport methods to compute the electric field from those interface fluxes, which simultaneously advances the induction equation and maintains the divergence of the magnetic field. A second-order divergence-free reconstruction technique is used to interpolate the magnetic fields in the block-structured adaptive mesh refinement framework already extant in Enzo. This reconstruction also preserves the divergence of the magnetic field to machine precision. We use operator splitting to include gravity and cosmological expansion. We then present a series of cosmological and non-cosmological test problems to demonstrate the quality of solution resulting from this combination of solvers.

  8. Visualization Tools for Adaptive Mesh Refinement Data

    SciTech Connect

    Weber, Gunther H.; Beckner, Vincent E.; Childs, Hank; Ligocki,Terry J.; Miller, Mark C.; Van Straalen, Brian; Bethel, E. Wes

    2007-05-09

    Adaptive Mesh Refinement (AMR) is a highly effective method for simulations that span a large range of spatiotemporal scales, such as astrophysical simulations that must accommodate ranges from interstellar to sub-planetary. Most mainstream visualization tools still lack support for AMR as a first class data type and AMR code teams use custom built applications for AMR visualization. The Department of Energy's (DOE's) Science Discovery through Advanced Computing (SciDAC) Visualization and Analytics Center for Enabling Technologies (VACET) is currently working on extending VisIt, which is an open source visualization tool that accommodates AMR as a first-class data type. These efforts will bridge the gap between general-purpose visualization applications and highly specialized AMR visual analysis applications. Here, we give an overview of the state of the art in AMR visualization research and tools and describe how VisIt currently handles AMR data.

  9. Visualization of Scalar Adaptive Mesh Refinement Data

    SciTech Connect

    VACET; Weber, Gunther; Weber, Gunther H.; Beckner, Vince E.; Childs, Hank; Ligocki, Terry J.; Miller, Mark C.; Van Straalen, Brian; Bethel, E. Wes

    2007-12-06

    Adaptive Mesh Refinement (AMR) is a highly effective computation method for simulations that span a large range of spatiotemporal scales, such as astrophysical simulations, which must accommodate ranges from interstellar to sub-planetary. Most mainstream visualization tools still lack support for AMR grids as a first class data type and AMR code teams use custom built applications for AMR visualization. The Department of Energy's (DOE's) Science Discovery through Advanced Computing (SciDAC) Visualization and Analytics Center for Enabling Technologies (VACET) is currently working on extending VisIt, which is an open source visualization tool that accommodates AMR as a first-class data type. These efforts will bridge the gap between general-purpose visualization applications and highly specialized AMR visual analysis applications. Here, we give an overview of the state of the art in AMR scalar data visualization research.

  10. Reference Documents | National Nuclear Security Administration...

    National Nuclear Security Administration (NNSA)

    Reference Documents Summary References Main Draft SEIS References Additional SEIS References Appendix C References Appendix D References Appendix E References Appendix F References ...

  11. ITP Petroleum Refining: Energy and Environmental Profile of the U.S.

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Petroleum Refining Industry (November 2007) | Department of Energy and Environmental Profile of the U.S. Petroleum Refining Industry (November 2007) ITP Petroleum Refining: Energy and Environmental Profile of the U.S. Petroleum Refining Industry (November 2007) profile.pdf (1.62 MB) More Documents & Publications ITP Petroleum Refining: Energy Bandwidth for Petroleum Refining Processes ITP Petroleum Refining: Energy and Environmental Profile of the U.S. Petroleum Refining Industry

  12. Secretary Bodman Tours Refinery and Calls for More Domestic Refining

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Capacity | Department of Energy Refinery and Calls for More Domestic Refining Capacity Secretary Bodman Tours Refinery and Calls for More Domestic Refining Capacity May 18, 2006 - 10:43am Addthis Highlights President Bush's Four-Point Plan to Combat High Energy Prices PORT ARTHUR, TX - Secretary of Energy Samuel W. Bodman today renewed the call for expanded oil refining capacity in the United States and discussed additional steps the Department of Energy (DOE) is taking to prepare for the

  13. REFINING PROGRAM HELPS REENERGIZE NEBRASKA UPGRADES | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    REFINING PROGRAM HELPS REENERGIZE NEBRASKA UPGRADES REFINING PROGRAM HELPS REENERGIZE NEBRASKA UPGRADES REFINING PROGRAM HELPS REENERGIZE NEBRASKA UPGRADES In a state where energy costs are low and the home performance workforce had not been established, Nebraska's two largest cities-Omaha and Lincoln-took on the challenge of promoting whole home energy upgrades to homeowners, businesses, and nonprofit organizations. Using $10 million in seed funding from the U.S. Department of Energy's (DOE's)

  14. Parallel adaptive mesh refinement for electronic structure calculations

    SciTech Connect

    Kohn, S.; Weare, J.; Ong, E.; Baden, S.

    1996-12-01

    We have applied structured adaptive mesh refinement techniques to the solution of the LDA equations for electronic structure calculations. Local spatial refinement concentrates memory resources and numerical effort where it is most needed, near the atomic centers and in regions of rapidly varying charge density. The structured grid representation enables us to employ efficient iterative solver techniques such as conjugate gradients with multigrid preconditioning. We have parallelized our solver using an object-oriented adaptive mesh refinement framework.

  15. The Five-Step Development Process Step 3: Project Refinement

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3: Project Refinement 2 1 Potential 3 Refinement 4 Implementation 5 Operations & Maintenance 2 Options 3 Refinement 3 FUNDING AND FINANCING OPTIONS Project Ownership Financing structure is highly dependent on size of the project and the capital available for a given project: * Tribe owns the project (cash purchase or debt) * Tribe hosts the project and buys the electricity (power purchase agreement) * Tribe partners with private sector and co-owns the project (uncertainties about receipt of

  16. ,"U.S. Reformulated, Average Refiner Gasoline Prices"

    Energy Information Administration (EIA) (indexed site)

    ...www.eia.govdnavpetpetprirefmg2cnusepm0rdpgalm.htm" ,"Source:","Energy Information ... Reformulated Gasoline Retail Sales by Refiners (Dollars per ...

  17. ,"U.S. Conventional, Average Refiner Gasoline Prices"

    Energy Information Administration (EIA) (indexed site)

    ...www.eia.govdnavpetpetprirefmg2cnusepm0udpgalm.htm" ,"Source:","Energy Information ... Conventional Gasoline Retail Sales by Refiners (Dollars per ...

  18. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Energy Information Administration (EIA) (indexed site)

    of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information Administration Petroleum Marketing Annual 1997 Table 43....

  19. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Energy Information Administration (EIA) (indexed site)

    1995 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) - Continued Geographic Area Month Premium All Grades Sales...

  20. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Energy Information Administration (EIA) (indexed site)

    2000 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per Day) - Continued Geographic Area Month Premium All Grades Sales...

  1. Petroleum Products Table 43. Refiner Motor Gasoline Volumes...

    Energy Information Administration (EIA) (indexed site)

    of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information Administration Petroleum Marketing Annual 1996 Table 43....

  2. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    Energy Information Administration Petroleum Marketing Annual 1995 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  3. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Energy Information Administration (EIA) (indexed site)

    250 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  4. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Energy Information Administration (EIA) (indexed site)

    Energy Information Administration Petroleum Marketing Annual 1995 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  5. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    134 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  6. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    134 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District, and State (Cents per Gallon...

  7. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    220 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  8. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Energy Information Administration (EIA) (indexed site)

    - - - - W W - - - - - - See footnotes at end of table. 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State 292 Energy...

  9. Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales...

    Energy Information Administration (EIA) (indexed site)

    250 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 44. Refiner Motor Gasoline Volumes by Formulation, Sales Type, PAD District, and State (Thousand Gallons...

  10. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    220 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  11. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    Energy Information Administration Petroleum Marketing Annual 1995 Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State (Thousand Gallons per...

  12. ,"U.S. Total Refiner Petroleum Product Prices"

    Energy Information Administration (EIA) (indexed site)

    NUSDPG","EMAEPPRPTGNUSDPG","EMAEPPRLPTGNUSDPG","EMAEPPRHPTGNUSDPG" "Date","U.S. Total Gasoline Retail Sales by Refiners (Dollars per Gallon)","U.S. Aviation Gasoline...

  13. Bandwidth Study U.S. Petroleum Refining | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. petroleum refining. The study relies on multiple sources to estimate the energy ...

  14. The Space-based Telescopes for Actionable Refinement of Ephemeris...

    Office of Scientific and Technical Information (OSTI)

    Title: The Space-based Telescopes for Actionable Refinement of Ephemeris (STARE) mission Authors: Riot, V ; Devries, W ; Bauman, B ; Simms, L ; Carter, D ; Phillion, D ; Olivier, S ...

  15. The Space-Based Telescopes for Actionable Refinement of Ephemeris...

    Office of Scientific and Technical Information (OSTI)

    Title: The Space-Based Telescopes for Actionable Refinement of Ephemeris Pathfinder Mission Authors: Simms, L ; De Vries, W ; RIot, V ; Olivier, S ; Pertica, A ; Bauman, B ; ...

  16. ITP Petroleum Refining: Petroleum Technology Vision 2020 | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Petroleum Technology Vision 2020 ITP Petroleum Refining: Petroleum Technology Vision 2020 techvision.pdf (684.96 KB) More Documents & Publications Manufacturing Energy and Carbon ...

  17. Refiners react to changes in the pipeline infrastructure

    SciTech Connect

    Giles, K.A.

    1997-06-01

    Petroleum pipelines have long been a critical component in the distribution of crude and refined products in the U.S. Pipelines are typically the most cost efficient mode of transportation for reasonably consistent flow rates. For obvious reasons, inland refineries and consumers are much more dependent on petroleum pipelines to provide supplies of crude and refined products than refineries and consumers located on the coasts. Significant changes in U.S. distribution patterns for crude and refined products are reshaping the pipeline infrastructure and presenting challenges and opportunities for domestic refiners. These changes are discussed.

  18. New Process for Grain Refinement of Aluminum. Final Report

    SciTech Connect

    Dr. Joseph A. Megy

    2000-09-22

    A new method of grain refining aluminum involving in-situ formation of boride nuclei in molten aluminum just prior to casting has been developed in the subject DOE program over the last thirty months by a team consisting of JDC, Inc., Alcoa Technical Center, GRAS, Inc., Touchstone Labs, and GKS Engineering Services. The Manufacturing process to make boron trichloride for grain refining is much simpler than preparing conventional grain refiners, with attendant environmental, capital, and energy savings. The manufacture of boride grain refining nuclei using the fy-Gem process avoids clusters, salt and oxide inclusions that cause quality problems in aluminum today.

  19. ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Energy Efficiency Roadmap for Petroleum Refineries in California ITP Petroleum Refining: Energy Efficiency Roadmap for Petroleum Refineries in California refiningroadmap.pdf (1.34 ...

  20. The Space-Based Telescopes for Actionable Refinement of Ephemeris...

    Office of Scientific and Technical Information (OSTI)

    Journal Article: The Space-Based Telescopes for Actionable Refinement of Ephemeris Pathfinder Mission Citation Details In-Document Search Title: The Space-Based Telescopes for ...

  1. Adaptive h -refinement for reduced-order models: ADAPTIVE h -refinement for reduced-order models

    DOE PAGES [OSTI]

    Carlberg, Kevin T.

    2014-11-05

    Our work presents a method to adaptively refine reduced-order models a posteriori without requiring additional full-order-model solves. The technique is analogous to mesh-adaptive h-refinement: it enriches the reduced-basis space online by ‘splitting’ a given basis vector into several vectors with disjoint support. The splitting scheme is defined by a tree structure constructed offline via recursive k-means clustering of the state variables using snapshot data. This method identifies the vectors to split online using a dual-weighted-residual approach that aims to reduce error in an output quantity of interest. The resulting method generates a hierarchy of subspaces online without requiring large-scale operationsmore » or full-order-model solves. Furthermore, it enables the reduced-order model to satisfy any prescribed error tolerance regardless of its original fidelity, as a completely refined reduced-order model is mathematically equivalent to the original full-order model. Experiments on a parameterized inviscid Burgers equation highlight the ability of the method to capture phenomena (e.g., moving shocks) not contained in the span of the original reduced basis.« less

  2. High frequency reference electrode

    DOEpatents

    Kronberg, James W.

    1994-01-01

    A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or "halo" at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes.

  3. High frequency reference electrode

    DOEpatents

    Kronberg, J.W.

    1994-05-31

    A high frequency reference electrode for electrochemical experiments comprises a mercury-calomel or silver-silver chloride reference electrode with a layer of platinum around it and a layer of a chemically and electrically resistant material such as TEFLON around the platinum covering all but a small ring or halo' at the tip of the reference electrode, adjacent to the active portion of the reference electrode. The voltage output of the platinum layer, which serves as a redox electrode, and that of the reference electrode are coupled by a capacitor or a set of capacitors and the coupled output transmitted to a standard laboratory potentiostat. The platinum may be applied by thermal decomposition to the surface of the reference electrode. The electrode provides superior high-frequency response over conventional electrodes. 4 figs.

  4. Optical voltage reference

    DOEpatents

    Rankin, R.; Kotter, D.

    1994-04-26

    An optical voltage reference for providing an alternative to a battery source is described. The optical reference apparatus provides a temperature stable, high precision, isolated voltage reference through the use of optical isolation techniques to eliminate current and impedance coupling errors. Pulse rate frequency modulation is employed to eliminate errors in the optical transmission link while phase-lock feedback is employed to stabilize the frequency to voltage transfer function. 2 figures.

  5. Optical voltage reference

    DOEpatents

    Rankin, Richard; Kotter, Dale

    1994-01-01

    An optical voltage reference for providing an alternative to a battery source. The optical reference apparatus provides a temperature stable, high precision, isolated voltage reference through the use of optical isolation techniques to eliminate current and impedance coupling errors. Pulse rate frequency modulation is employed to eliminate errors in the optical transmission link while phase-lock feedback is employed to stabilize the frequency to voltage transfer function.

  6. Appendix A: Reference case

    Annual Energy Outlook

    Reference case Energy Information Administration Annual Energy Outlook 2014 Table A17. Renewable energy consumption by sector and source (quadrillion Btu) Sector and source...

  7. Appendix A: Reference case

    Annual Energy Outlook

    4 Reference case Table A2. Energy consumption by sector and source (quadrillion Btu per year, unless otherwise noted) Energy Information Administration Annual Energy Outlook 2014...

  8. EFRC Management Reference Document

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    EFRC management reference document Energy Frontier Research Centers Acknowledgments of Support (v.1, October 2009) Office of Basic Energy Sciences Office of Science US Department ...

  9. Steel refining with an electrochemical cell

    DOEpatents

    Blander, Milton; Cook, Glenn M.

    1988-01-01

    Apparatus for processing a metallic fluid containing iron oxide, container for a molten metal including an electrically conductive refractory disposed for contact with the molten metal which contains iron oxide, an electrolyte in the form of a basic slag on top of the molten metal, an electrode in the container in contact with the slag electrically separated from the refractory, and means for establishing a voltage across the refractory and the electrode to reduce iron oxide to iron at the surface of the refractory in contact with the iron oxide containing fluid. A process is disclosed for refining an iron product containing not more than about 10% by weight oxygen and not more than about 10% by weight sulfur, comprising providing an electrolyte of a slag containing one or more of calcium oxide, magnesium oxide, silica or alumina, providing a cathode of the iron product in contact with the electrolyte, providing an anode in contact with the electrolyte electrically separated from the cathode, and operating an electrochemical cell formed by the anode, the cathode and the electrolyte to separate oxygen or sulfur present in the iron product therefrom.

  10. Steel refining with an electrochemical cell

    DOEpatents

    Blander, M.; Cook, G.M.

    1988-05-17

    Apparatus is described for processing a metallic fluid containing iron oxide, container for a molten metal including an electrically conductive refractory disposed for contact with the molten metal which contains iron oxide, an electrolyte in the form of a basic slag on top of the molten metal, an electrode in the container in contact with the slag electrically separated from the refractory, and means for establishing a voltage across the refractory and the electrode to reduce iron oxide to iron at the surface of the refractory in contact with the iron oxide containing fluid. A process is disclosed for refining an iron product containing not more than about 10% by weight oxygen and not more than about 10% by weight sulfur, comprising providing an electrolyte of a slag containing one or more of calcium oxide, magnesium oxide, silica or alumina, providing a cathode of the iron product in contact with the electrolyte, providing an anode in contact with the electrolyte electrically separated from the cathode, and operating an electrochemical cell formed by the anode, the cathode and the electrolyte to separate oxygen or sulfur present in the iron product therefrom. 2 figs.

  11. Steel refining with an electrochemical cell

    DOEpatents

    Blander, M.; Cook, G.M.

    1985-05-21

    Disclosed is an apparatus for processing a metallic fluid containing iron oxide, container for a molten metal including an electrically conductive refractory disposed for contact with the molten metal which contains iron oxide, an electrolyte in the form of a basic slag on top of the molten metal, an electrode in the container in contact with the slag electrically separated from the refractory, and means for establishing a voltage across the refractory and the electrode to reduce iron oxide to iron at the surface of the refractory in contact with the iron oxide containing fluid. A process is disclosed for refining an iron product containing not more than about 10% by weight sulfur, comprising providing an electrolyte of a slag containing one or more of calcium oxide, magnesium oxide, silica or alumina, providing a cathode of the iron product in contact with the electrolyte, providing an anode in contact with the electrolyte electrically separated from the cathode, and operating an electrochemical cell formed by the anode, the cathode and the electrolyte to separate oxygen or sulfur present in the iron product therefrom.

  12. Refining and End Use Study of Coal Liquids

    SciTech Connect

    1997-10-01

    This report summarizes revisions to the design basis for the linear programing refining model that is being used in the Refining and End Use Study of Coal Liquids. This revision primarily reflects the addition of data for the upgrading of direct coal liquids.

  13. ,"Motor Gasoline Sales to End Users, Total Refiner Sales Volumes...

    Energy Information Administration (EIA) (indexed site)

    ... Refiners (Thousand Gallons per Day)","New Mexico Total Gasoline Retail Sales by Refiners ...87,16127.8,1684.4,1377.2,128.8,497.8,835.6,2030.3,1178.7,674.5,56.4,3.9,4678.6,764.1,9.3,1...

  14. ,"No. 2 Distillate Sales to End Users Refiner Sales Volumes"

    Energy Information Administration (EIA) (indexed site)

    ... Refiners (Thousand Gallons per Day)","New Mexico No 2 Distillate Retail Sales by Refiners ...57.7,6018.7,64.6,101.5,691.5,1553.8,1576.9,2030.5,4320.3,1350.4,683.2,792.4,316.4,804.3,37...

  15. Reitveld refinement study of PLZT ceramics

    SciTech Connect

    Kumar, Rakesh; Bavbande, D. V.; Bafna, V. H.; Mohan, D.; Kothiyal, G. P.; Mishra, R.

    2013-02-05

    PLZT ceramics of composition Pb{sub 0.93}La{sub 0.07}(Zr{sub 0.60}Ti{sub 0.40})O{sub 3}, have been milled for 6hrs and 24hrs were prepared by solid state synthesis route. The 6hrs milled and 24hrs milled samples are represented as PLZT-6 and PLZT-24 ceramics respectively. X-ray diffraction (XRD) pattern was recorded at room temperature. The XRD pattern has been analyzed by employing Rietveld refinement method. Phase identification shows that all the peaks observed in PLZT-6 and PLZT-24 ceramics could be indexed to P4mm space group with tetragonal symmetry. The unit cell parameters of 6hrs milled PLZT ceramics are found to be a=b=4.0781(5)A and c=4.0938(7)A and for 24hrs milled PLZT ceramics unit cell parameters are a=b=4.0679(4)A and c=4.1010(5)A . The axial ratio c/a and unit cell volume of PLZT-6 are 1.0038 and 68.09(2)A{sup 3} respectively. In PLZT-24 samples, the axial ratio c/a value is 1.0080 which is little more than that of the 6hr milled PLZT sample whereas the unit cell volume decrease to 67.88 (1) A{sup 3}. An average crystallite size was estimated by using Scherrer's formula. Dielectric properties were obtained by measuring the capacitance and tand loss using Stanford LCR meter.

  16. Uranium reference materials

    SciTech Connect

    Donivan, S.; Chessmore, R.

    1987-07-01

    The Technical Measurements Center has prepared uranium mill tailings reference materials for use by remedial action contractors and cognizant federal and state agencies. Four materials were prepared with varying concentrations of radionuclides, using three tailings materials and a river-bottom soil diluent. All materials were ground, dried, and blended thoroughly to ensure homogeneity. The analyses on which the recommended values for nuclides in the reference materials are based were performed, using independent methods, by the UNC Geotech (UNC) Chemistry Laboratory, Grand Junction, Colorado, and by C.W. Sill (Sill), Idaho National Engineering Laboratory, Idaho Falls, Idaho. Several statistical tests were performed on the analytical data to characterize the reference materials. Results of these tests reveal that the four reference materials are homogeneous and that no large systematic bias exists between the analytical methods used by Sill and those used by TMC. The average values for radionuclides of the two data sets, representing an unbiased estimate, were used as the recommended values for concentrations of nuclides in the reference materials. The recommended concentrations of radionuclides in the four reference materials are provided. Use of these reference materials will aid in providing uniform standardization among measurements made by remedial action contractors. 11 refs., 9 tabs.

  17. Sandia Energy - Reference Model Documents

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Documents Home Stationary Power Energy Conversion Efficiency Water Power Reference Model Project (RMP) Reference Model Documents Reference Model DocumentsTara Camacho-Lopez2015-05-...

  18. reference | OpenEI Community

    OpenEI (Open Energy Information) [EERE & EIA]

    reference Home Jweers's picture Submitted by Jweers(88) Contributor 7 August, 2013 - 18:23 New Robust References citation citing developer formatting reference Semantic Mediawiki...

  19. Multifunctional reference electrode (Patent) | DOEPatents

    Office of Scientific and Technical Information (OSTI)

    Multifunctional reference electrode Title: Multifunctional reference electrode A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the ...

  20. REFERENCES Baines, W. D.

    Office of Scientific and Technical Information (OSTI)

    REFERENCES Baines, W. D. aud Peterson, E. G., 1951, "An Investigation of Flow Through ... D 50.8 m. A flow facility has been constructed for experiments with these screens. Air ...

  1. Value of Information References

    DOE Data Explorer

    Morency, Christina

    This file contains a list of relevant references on value of information (VOI) in RIS format. VOI provides a quantitative analysis to evaluate the outcome of the combined technologies (seismology, hydrology, geodesy) used to monitor Brady's Geothermal Field.

  2. Value of Information References

    DOE Data Explorer

    Morency, Christina

    2014-12-12

    This file contains a list of relevant references on value of information (VOI) in RIS format. VOI provides a quantitative analysis to evaluate the outcome of the combined technologies (seismology, hydrology, geodesy) used to monitor Brady's Geothermal Field.

  3. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Petroleum Refining

    SciTech Connect

    Sabine Brueske, Caroline Kramer, Aaron Fisher

    2015-06-01

    Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. petroleum refining. The study relies on multiple sources to estimate the energy used in nine individual process areas, representing 68% of sector-wide energy consumption. Energy savings opportunities for individual processes are based on technologies currently in use or under development; these potential savings are then extrapolated to estimate sector-wide energy savings opportunity.

  4. Precision displacement reference system

    DOEpatents

    Bieg, Lothar F.; Dubois, Robert R.; Strother, Jerry D.

    2000-02-22

    A precision displacement reference system is described, which enables real time accountability over the applied displacement feedback system to precision machine tools, positioning mechanisms, motion devices, and related operations. As independent measurements of tool location is taken by a displacement feedback system, a rotating reference disk compares feedback counts with performed motion. These measurements are compared to characterize and analyze real time mechanical and control performance during operation.

  5. Membrane reference electrode

    DOEpatents

    Redey, Laszlo; Bloom, Ira D.

    1989-01-01

    A reference electrode utilizes a small thin, flat membrane of a highly conductive glass placed on a small diameter insulator tube having a reference material inside in contact with an internal voltage lead. When the sensor is placed in a non-aqueous ionic electrolytic solution, the concentration difference across the glass membrane generates a low voltage signal in precise relationship to the concentration of the species to be measured with high spatial resolution.

  6. Membrane reference electrode

    DOEpatents

    Redey, L.; Bloom, I.D.

    1988-01-21

    A reference electrode utilizes a small thin, flat membrane of a highly conductive glass placed on a small diameter insulator tube having a reference material inside in contact with an internal voltage lead. When the sensor is placed in a non-aqueous ionic electrolytic solution, the concentration difference across the glass membrane generates a low voltage signal in precise relationship to the concentration of the species to be measured, with high spatial resolution. 2 figs.

  7. Integrated process for the solvent refining of coal

    DOEpatents

    Garg, Diwakar

    1983-01-01

    A process is set forth for the integrated liquefaction of coal by the catalytic solvent refining of a feed coal in a first stage to liquid and solid products and the catalytic hydrogenation of the solid product in a second stage to produce additional liquid product. A fresh inexpensive, throw-away catalyst is utilized in the second stage hydrogenation of the solid product and this catalyst is recovered and recycled for catalyst duty in the solvent refining stage without any activation steps performed on the used catalyst prior to its use in the solvent refining of feed coal.

  8. The NEPA reference guide

    SciTech Connect

    Swartz, L.L.; Reinke, D.C.

    1999-10-01

    The NEPA Reference Guide conveniently organizes and indexes National Environmental Policy Act (NEPA) and Council on Environmental Quality (CEQ) regulations and guidance, along with relevant federal case law, all in one place. It allows the user to quickly learn the statutory, regulatory, and case law authority for a large number of NEPA subjects. A unique feature of The NEPA Reference Guide is its detailed index that includes a large number of diverse NEPA subjects. The index enables users to find and compile any statutory, regulatory (including CEQ guidance), and case law original source material and references on virtually any NEPA subject. This will be an especially useful tool for new NEPA practitioners who need to become immersed in a particular subject quickly.

  9. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    253.2 2,222.4 W W 206.4 134.3 - 340.7 See footnotes at end of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information...

  10. Table 43. Refiner Motor Gasoline Volumes by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    150.0 2,026.7 W W 234.5 161.7 - 396.3 See footnotes at end of table. 43. Refiner Motor Gasoline Volumes by Grade, Sales Type, PAD District, and State 262 Energy Information...

  11. May 28 Webinar to Focus on Tribal Energy Project Refinement

    Energy.gov [DOE]

    Register for the Tribal Renewable Energy Project Refinement webinar, which will be held on Wednesday, May 28, 2014, from 11 a.m. to 12:30 p.m. Mountain time.

  12. Multifunctional reference electrode

    DOEpatents

    Redey, Laszlo; Vissers, Donald R.

    1983-01-01

    A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the nickel tube electrically insulated therefrom for measuring the temperature thereof, a housing surrounding the nickel tube, an electrolyte having a fixed sulfide ion activity between the housing and the outer surface of the nickel tube forming the nickel/nickel sulfide/sulfide half-cell. An ion diffusion barrier is associated with the housing in contact with the electrolyte. Also disclosed is a cell using the reference electrode to measure characteristics of a working electrode.

  13. Aluminum reference electrode

    DOEpatents

    Sadoway, D.R.

    1988-08-16

    A stable reference electrode is described for use in monitoring and controlling the process of electrolytic reduction of a metal. In the case of Hall cell reduction of aluminum, the reference electrode comprises a pool of molten aluminum and a solution of molten cryolite, Na[sub 3]AlF[sub 6], wherein the electrical connection to the molten aluminum does not contact the highly corrosive molten salt solution. This is accomplished by altering the density of either the aluminum (decreasing the density) or the electrolyte (increasing the density) so that the aluminum floats on top of the molten salt solution. 1 fig.

  14. Aluminum reference electrode

    DOEpatents

    Sadoway, Donald R.

    1988-01-01

    A stable reference electrode for use in monitoring and controlling the process of electrolytic reduction of a metal. In the case of Hall cell reduction of aluminum, the reference electrode comprises a pool of molten aluminum and a solution of molten cryolite, Na.sub.3 AlF.sub.6, wherein the electrical connection to the molten aluminum does not contact the highly corrosive molten salt solution. This is accomplished by altering the density of either the aluminum (decreasing the density) or the electrolyte (increasing the density) so that the aluminum floats on top of the molten salt solution.

  15. Multifunctional reference electrode

    DOEpatents

    Redey, L.; Vissers, D.R.

    1981-12-30

    A multifunctional, low mass reference electrode of a nickel tube, thermocouple means inside the nickel tube electrically insulated therefrom for measuring the temperature thereof, a housing surrounding the nickel tube, an electrolyte having a fixed sulfide ion activity between the housing and the outer surface of the nickel tube forming the nickel/nickel sulfide/sulfide half-cell are described. An ion diffusion barrier is associated with the housing in contact with the electrolyte. Also disclosed is a cell using the reference electrode to measure characteristics of a working electrode.

  16. Waste minimization for selected residuals in the petroleum refining industry

    SciTech Connect

    1996-12-01

    This technical report on residuals in the petroleum refining industry provides an industry overview, process description, and process flow diagrams. It presents residual descriptions for each of the 29 petroleum refining residuals of concern and what source reduction option exist. It reviews the data sources - RCRA Section 2007 surveys, site visits, and journal articles. It also describes major findings and evaluates the quantity and quality of waste minization information for each source.

  17. Hydrogen Piping Experience in Chevron Refining | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Piping Experience in Chevron Refining Hydrogen Piping Experience in Chevron Refining Overall Perspectives: Few problems with hydrogen piping operating at ambient to at least 800F and pressures up to at least 3000psia as long as we stay within well-defined limits hpwgw_chevronrefining_niccolls.pdf (373.32 KB) More Documents & Publications DOE Hydrogen Pipeline Working Group Workshop Hydrogen Pipeline Working Group Workshop: Code for Hydrogen Pipelines A Review of Stress Corrosion

  18. EERE Success Story-Refining Bio-Oil alongside Petroleum | Department...

    Office of Environmental Management (EM)

    Refining Bio-Oil alongside Petroleum EERE Success Story-Refining Bio-Oil alongside Petroleum April 9, 2013 - 12:00am Addthis W.R. Grace, a leading provider of refining ...

  19. Reference Model Development

    SciTech Connect

    Jepsen, Richard

    2011-11-02

    Presentation from the 2011 Water Peer Review in which principal investigator discusses project progress to develop a representative set of Reference Models (RM) for the MHK industry to develop baseline cost of energy (COE) and evaluate key cost component/system reduction pathways.

  20. OSH technical reference manual

    SciTech Connect

    Not Available

    1993-11-01

    In an evaluation of the Department of Energy (DOE) Occupational Safety and Health programs for government-owned contractor-operated (GOCO) activities, the Department of Labor`s Occupational Safety and Health Administration (OSHA) recommended a technical information exchange program. The intent was to share written safety and health programs, plans, training manuals, and materials within the entire DOE community. The OSH Technical Reference (OTR) helps support the secretary`s response to the OSHA finding by providing a one-stop resource and referral for technical information that relates to safe operations and practice. It also serves as a technical information exchange tool to reference DOE-wide materials pertinent to specific safety topics and, with some modification, as a training aid. The OTR bridges the gap between general safety documents and very specific requirements documents. It is tailored to the DOE community and incorporates DOE field experience.

  1. Alignment reference device

    DOEpatents

    Patton, Gail Y.; Torgerson, Darrel D.

    1987-01-01

    An alignment reference device provides a collimated laser beam that minimizes angular deviations therein. A laser beam source outputs the beam into a single mode optical fiber. The output end of the optical fiber acts as a source of radiant energy and is positioned at the focal point of a lens system where the focal point is positioned within the lens. The output beam reflects off a mirror back to the lens that produces a collimated beam.

  2. Chapter 6 - References

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    6-1 CHAPTER 6 REFERENCES BLS (Bureau of Labor Statistics), 2002. Bureau of Labor Statistics Data, <http://www.bls.gov/data>, accessed January 25. CAIRS (Computerized Accident/Incident Reporting System), 2002. Statistics, <http://www.eh.doe.gov/cairs/stats.html>, accessed January 30. CEMRC (Carlsbad Environmental Monitoring & Research Center), 2000. Actinide Chemistry and Repository Science Laboratory Initiative, New Mexico State University, Carlsbad, New Mexico, December 15. CEQ

  3. Toward parallel, adaptive mesh refinement for chemically reacting flow simulations

    SciTech Connect

    Devine, K.D.; Shadid, J.N.; Salinger, A.G. Hutchinson, S.A.; Hennigan, G.L.

    1997-12-01

    Adaptive numerical methods offer greater efficiency than traditional numerical methods by concentrating computational effort in regions of the problem domain where the solution is difficult to obtain. In this paper, the authors describe progress toward adding mesh refinement to MPSalsa, a computer program developed at Sandia National laboratories to solve coupled three-dimensional fluid flow and detailed reaction chemistry systems for modeling chemically reacting flow on large-scale parallel computers. Data structures that support refinement and dynamic load-balancing are discussed. Results using uniform refinement with mesh sequencing to improve convergence to steady-state solutions are also presented. Three examples are presented: a lid driven cavity, a thermal convection flow, and a tilted chemical vapor deposition reactor.

  4. The US petroleum refining industry in the 1980's

    SciTech Connect

    Not Available

    1990-10-11

    As part of the EIA program on petroleum, The US Petroleum Refining Industry in the 1980's, presents a historical analysis of the changes that took place in the US petroleum refining industry during the 1980's. It is intended to be of interest to analysts in the petroleum industry, state and federal government officials, Congress, and the general public. The report consists of six chapters and four appendices. Included is a detailed description of the major events and factors that affected the domestic refining industry during this period. Some of the changes that took place in the 1980's are the result of events that started in the 1970's. The impact of these events on US refinery configuration, operations, economics, and company ownership are examined. 23 figs., 11 tabs.

  5. Coal Data: A reference

    SciTech Connect

    Not Available

    1991-11-26

    The purpose of Coal Data: A Reference is to provide basic information on the mining and use of coal, an important source of energy in the United States. The report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ``Coal Terminology and Related Information`` provides additional information about terms mentioned in the text and introduces new terms. Topics covered are US coal deposits, resources and reserves, mining, production, employment and productivity, health and safety, preparation, transportation, supply and stocks, use, coal, the environment, and more. (VC)

  6. Trends in heavy oil production and refining in California

    SciTech Connect

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10{degrees} to 20{degrees} API gravity) production in California has increased from 20% of the state`s total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation`s energy production and refining capability. California is the recipient and refines most of Alaska`s 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources.

  7. Trends in heavy oil production and refining in California

    SciTech Connect

    Olsen, D.K.; Ramzel, E.B.; Pendergrass, R.A. II.

    1992-07-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production and is part of a study being conducted for the US Department of Energy. This report summarizes trends in oil production and refining in Canada. Heavy oil (10{degrees} to 20{degrees} API gravity) production in California has increased from 20% of the state's total oil production in the early 1940s to 70% in the late 1980s. In each of the three principal petroleum producing districts (Los Angeles Basin, Coastal Basin, and San Joaquin Valley) oil production has peaked then declined at different times throughout the past 30 years. Thermal production of heavy oil has contributed to making California the largest producer of oil by enhanced oil recovery processes in spite of low oil prices for heavy oil and stringent environmental regulation. Opening of Naval Petroleum Reserve No. 1, Elk Hills (CA) field in 1976, brought about a major new source of light oil at a time when light oil production had greatly declined. Although California is a major petroleum-consuming state, in 1989 the state used 13.3 billion gallons of gasoline or 11.5% of US demand but it contributed substantially to the Nation's energy production and refining capability. California is the recipient and refines most of Alaska's 1.7 million barrel per day oil production. With California production, Alaskan oil, and imports brought into California for refining, California has an excess of oil and refined products and is a net exporter to other states. The local surplus of oil inhibits exploitation of California heavy oil resources even though the heavy oil resources exist. Transportation, refining, and competition in the market limit full development of California heavy oil resources.

  8. PROP re-refined oil engine test performance

    SciTech Connect

    Linnard, R.E.

    1980-11-01

    Using conventional, commercially-available nonproprietary (to Phillips) additive treatments, engine test programs have successfully demonstrated Phillips Re-refined Oil Process (PROP) oils' compliance with the performance requirements of MIL-L-46152A and API Services SE/CC. This paper reports on the engine testing experience with PROP refined oils as produced in a full-scale 2 MM GPY PROP plant operating with Buyer-collected used oil feedstocks. Comment is also made on the status of the first two PROP plants, one built for the state of North Carolina and the other for Mohawk Oil Company, Ltd., Vancouver B.C., Canada.

  9. Coal data: A reference

    SciTech Connect

    Not Available

    1995-02-01

    This report, Coal Data: A Reference, summarizes basic information on the mining and use of coal, an important source of energy in the US. This report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ``Supplemental Figures and Tables`` contains statistics, graphs, maps, and other illustrations that show trends, patterns, geographic locations, and similar coal-related information. The section ``Coal Terminology and Related Information`` provides additional information about terms mentioned in the text and introduces some new terms. The last edition of Coal Data: A Reference was published in 1991. The present edition contains updated data as well as expanded reviews and additional information. Added to the text are discussions of coal quality, coal prices, unions, and strikes. The appendix has been expanded to provide statistics on a variety of additional topics, such as: trends in coal production and royalties from Federal and Indian coal leases, hours worked and earnings for coal mine employment, railroad coal shipments and revenues, waterborne coal traffic, coal export loading terminals, utility coal combustion byproducts, and trace elements in coal. The information in this report has been gleaned mainly from the sources in the bibliography. The reader interested in going beyond the scope of this report should consult these sources. The statistics are largely from reports published by the Energy Information Administration.

  10. Antares Reference Telescope System

    SciTech Connect

    Viswanathan, V.K.; Kaprelian, E.; Swann, T.; Parker, J.; Wolfe, P.; Woodfin, G.; Knight, D.

    1983-01-01

    Antares is a 24-beam, 40-TW carbon-dioxide laser-fusion system currently nearing completion at the Los Alamos National Laboratory. The 24 beams will be focused onto a tiny target (typically 300 to 1000 ..mu..m in diameter) located approximately at the center of a 7.3-m-diameter by 9.3-m-long vacuum (10/sup -6/ torr) chamber. The design goal is to position the targets to within 10 ..mu..m of a selected nominal position, which may be anywhere within a fixed spherical region 1 cm in diameter. The Antares Reference Telescope System is intended to help achieve this goal for alignment and viewing of the various targets used in the laser system. The Antares Reference Telescope System consists of two similar electro-optical systems positioned in a near orthogonal manner in the target chamber area of the laser. Each of these consists of four subsystems: (1) a fixed 9X optical imaging subsystem which produces an image of the target at the vidicon; (2) a reticle projection subsystem which superimposes an image of the reticle pattern at the vidicon; (3) an adjustable front-lighting subsystem which illuminates the target; and (4) an adjustable back-lighting subsystem which also can be used to illuminate the target. The various optical, mechanical, and vidicon design considerations and trade-offs are discussed. The final system chosen (which is being built) and its current status are described in detail.

  11. STEP Intern Reference Check Sheet

    Energy.gov [DOE]

    STEP Intern Reference Check Sheet, from the Tool Kit Framework: Small Town University Energy Program (STEP).

  12. Nuclear Science References Database

    SciTech Connect

    Pritychenko, B.; Běták, E.; Singh, B.; Totans, J.

    2014-06-15

    The Nuclear Science References (NSR) database together with its associated Web interface, is the world's only comprehensive source of easily accessible low- and intermediate-energy nuclear physics bibliographic information for more than 210,000 articles since the beginning of nuclear science. The weekly-updated NSR database provides essential support for nuclear data evaluation, compilation and research activities. The principles of the database and Web application development and maintenance are described. Examples of nuclear structure, reaction and decay applications are specifically included. The complete NSR database is freely available at the websites of the National Nuclear Data Center (http://www.nndc.bnl.gov/nsr) and the International Atomic Energy Agency (http://www-nds.iaea.org/nsr)

  13. Long life reference electrode

    DOEpatents

    Yonco, Robert M.; Nagy, Zoltan

    1989-01-01

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservior and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved.

  14. Long life reference electrode

    DOEpatents

    Yonco, R.M.; Nagy, Z.

    1989-04-04

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservoir and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved. 2 figs.

  15. Long life reference electrode

    DOEpatents

    Yonco, R.M.; Nagy, Z.

    1987-07-30

    An external, reference electrode is provided for long term use with a high temperature, high pressure system. The electrode is arranged in a vertical, electrically insulative tube with an upper portion serving as an electrolyte reservoir and a lower portion in electrolytic communication with the system to be monitored. The lower end portion includes a flow restriction such as a porous plug to limit the electrolyte release into the system. A piston equalized to the system pressure is fitted into the upper portion of the tube to impart a small incremental pressure to the electrolyte. The piston is selected of suitable size and weight to cause only a slight flow of electrolyte through the porous plug into the high pressure system. This prevents contamination of the electrolyte but is of such small flow rate that operating intervals of a month or more can be achieved. 2 figs.

  16. Energy Efficiency Improvement in the Petroleum RefiningIndustry

    SciTech Connect

    Worrell, Ernst; Galitsky, Christina

    2005-05-01

    Information has proven to be an important barrier inindustrial energy efficiency improvement. Voluntary government programsaim to assist industry to improve energy efficiency by supplyinginformation on opportunities. ENERGY STAR(R) supports the development ofstrong strategic corporate energy management programs, by providingenergy management information tools and strategies. This paper summarizesENERGY STAR research conducted to develop an Energy Guide for thePetroleum Refining industry. Petroleum refining in the United States isthe largest in the world, providing inputs to virtually every economicsector, including the transport sector and the chemical industry.Refineries spend typically 50 percent of the cash operating costs (e.g.,excluding capital costs and depreciation) on energy, making energy amajor cost factor and also an important opportunity for cost reduction.The petroleum refining industry consumes about 3.1 Quads of primaryenergy, making it the single largest industrial energy user in the UnitedStates. Typically, refineries can economically improve energy efficiencyby 20 percent. The findings suggest that given available resources andtechnology, there are substantial opportunities to reduce energyconsumption cost-effectively in the petroleum refining industry whilemaintaining the quality of the products manufactured.

  17. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    2. U.S. Refiner Retail Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1995 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No. 4...

  18. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    4. U.S. Refiner Wholesale Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1997 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No....

  19. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    4. U.S. Refiner Wholesale Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1995 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No....

  20. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    2. U.S. Refiner Retail Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1996 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No. 4...

  1. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    Prices J F M A M J J A S O N D 0 10 20 30 40 50 60 70 1995 Cents per Gallon Excluding Taxes Retail < or 1% Wholesale < or 1% Retail > 1% Wholesale > 1% 7. U.S. Refiner Residual...

  2. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    4. U.S. Refiner Wholesale Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1996 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No....

  3. Source: Energy Information Administration, Form EIA-782A, "Refiners...

    Energy Information Administration (EIA) (indexed site)

    2. U.S. Refiner Retail Petroleum Product Prices Figure J F M A M J J A S O N D 0 20 40 60 80 100 120 1997 Cents per Gallon Excluding Taxes Kero-jet Propane No. 1 Distillate No. 4...

  4. Decontamination of transuranic contaminated metals by melt refining

    SciTech Connect

    Heshmatpour, B.; Copeland, G.L.; Heestand, R.L.

    1983-01-01

    Melt refining of transuranic contaminated metals is a possible decontamination process with the potential advantages of producing metal for reuse and of simplifying chemical analyses. By routinely achieving the 10 nCi/g( about0.1ppm) level by melt refining, scrap metal can be removed from the transuranic waste category. (To demonstrate the effectiveness of this melt refining process, mild steel, stainless steel, nickel, and copper were contaminated with 500 ppm (..mu..g/g) PuO/sub 2/ and melted with various fluxes. The solidified slags and metals were analyzed for their plutonium contents, and corresponding partition ratios for plutonium were calculated. Some metals were double refined in order to study the effect of secondary slag treatment. The initial weight of the slags was also varied to investigate the effect of slag weight on the degree of plutonium removal. In general, all four metals could be decontaminated below 1 ppm (..mu..g/g) Pu ( about100 nCi/g) by a single slag treatment. Doubling the slag weight did not improve decontamination significantly; however, double slag treatment using 5 wt.% slag did decontaminate the metals to below 0.1 ppm (..mu..g/g) Pu (10 nCi/g).)

  5. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    71.8 W 70.5 78.9 W 76.0 83.6 W 69.2 75.2 See footnotes at end of table. 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District and State 176 Energy Information...

  6. Table 35. Refiner Motor Gasoline Prices by Grade, Sales Type...

    Energy Information Administration (EIA) (indexed site)

    W 68.4 70.8 W W 78.6 W 85.7 81.8 W 69.3 73.8 See footnotes at end of table. 35. Refiner Motor Gasoline Prices by Grade, Sales Type, PAD District and State 176 Energy Information...

  7. Process for electroslag refining of uranium and uranium alloys

    DOEpatents

    Lewis, P.S. Jr.; Agee, W.A.; Bullock, J.S. IV; Condon, J.B.

    1975-07-22

    A process is described for electroslag refining of uranium and uranium alloys wherein molten uranium and uranium alloys are melted in a molten layer of a fluoride slag containing up to about 8 weight percent calcium metal. The calcium metal reduces oxides in the uranium and uranium alloys to provide them with an oxygen content of less than 100 parts per million. (auth)

  8. ITP Petroleum Refining: Technology Roadmap for the Petroleum Industry |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Technology Roadmap for the Petroleum Industry ITP Petroleum Refining: Technology Roadmap for the Petroleum Industry petroleumroadmap.pdf (338.1 KB) More Documents & Publications ITP Aluminum: Energy and Environmental Profile of the U.S. Aluminum Industry ITP Aluminum: Technical Working Group on Inert Anode Technologies 2011 Strategic Plan

  9. ,"Conventional Gasoline Sales to End Users, Total Refiner Sales...

    Energy Information Administration (EIA) (indexed site)

    ... Refiners (Thousand Gallons per Day)","New Mexico Conventional Gasoline Retail Sales by ...928.8,,587,12358.1,196,1145.9,128.8,497.8,,2030.3,,459.7,56.4,3.9,4678.6,764.1,9.3,1677.4,...

  10. Early F-type stars - refined classification, confrontation with Stromgren photometry, and the effects of rotation

    SciTech Connect

    Gray, R.O.; Garrison, R.F.

    1989-02-01

    The classification for early F-type stars in the MK spectral classification system presented by Gray and Garrison (1987) is refined. The effect of rotation on spectral classification and ubvy-beta photometry of early F-type stars is examined. It is found that the classical luminosity criterion, the 4417 A/4481 A ratio gives inconsistent results. It is shown that most of the stars in the Delta Delphini class of metallic-line stars are either normal or are indistinguishable from proto-Am stars. It is suggested that the designation Delta Delphini should be dropped. The classifications are compared with Stromgren photometry. The effects of rotation on the delta-c sub 1 index in the early-F field dwarfs is demonstrated. 55 references.

  11. Sensor Characteristics Reference Guide

    SciTech Connect

    Cree, Johnathan V.; Dansu, A.; Fuhr, P.; Lanzisera, Steven M.; McIntyre, T.; Muehleisen, Ralph T.; Starke, M.; Banerjee, Pranab; Kuruganti, T.; Castello, C.

    2013-04-01

    The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systems through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased information

  12. REFINING AND END USE STUDY OF COAL LIQUIDS

    SciTech Connect

    Unknown

    2002-01-01

    This document summarizes all of the work conducted as part of the Refining and End Use Study of Coal Liquids. There were several distinct objectives set, as the study developed over time: (1) Demonstration of a Refinery Accepting Coal Liquids; (2) Emissions Screening of Indirect Diesel; (3) Biomass Gasification F-T Modeling; and (4) Updated Gas to Liquids (GTL) Baseline Design/Economic Study.

  13. Environmental Regulations and Changes in Petroleum Refining Operations

    Gasoline and Diesel Fuel Update

    Environmental Regulations and Changes in Petroleum Refining Operations By Tancred C.M. Lidderdale Contents * Introduction * Motor Gasoline Summer Volatility (RVP) Regulations o Table 1. Summer Volatility Regulations for Motor Gasoline o Table 2. Refinery Inputs and Production of Normal Butane o Figure 1. Refinery Inputs and Production of Normal Butane o Table 3. Price Relationship Between Normal Butane and Motor Gasoline o Table 4. Market Price Premium for Low Vapor Pressure (RVP) Gasoline *

  14. Capillary reference half-cell

    DOEpatents

    Hall, S.H.

    1996-02-13

    The present invention is a reference half-cell electrode wherein intermingling of test fluid with reference fluid does not affect the performance of the reference half-cell over a long time. This intermingling reference half-cell may be used as a single or double junction submersible or surface reference electrode. The intermingling reference half-cell relies on a capillary tube having a first end open to reference fluid and a second end open to test fluid wherein the small diameter of the capillary tube limits free motion of fluid within the capillary to diffusion. The electrode is placed near the first end of the capillary in contact with the reference fluid. The method of operation of the present invention begins with filling the capillary tube with a reference solution. After closing the first end of the capillary, the capillary tube may be fully submerged or partially submerged with the second open end inserted into test fluid. Since the electrode is placed near the first end of the capillary, and since the test fluid may intermingle with the reference fluid through the second open end only by diffusion, this intermingling capillary reference half-cell provides a stable voltage potential for long time periods. 11 figs.

  15. Capillary reference half-cell

    DOEpatents

    Hall, Stephen H.

    1996-01-01

    The present invention is a reference half-cell electrode wherein intermingling of test fluid with reference fluid does not affect the performance of the reference half-cell over a long time. This intermingling reference half-cell may be used as a single or double junction submersible or surface reference electrode. The intermingling reference half-cell relies on a capillary tube having a first end open to reference fluid and a second end open to test fluid wherein the small diameter of the capillary tube limits free motion of fluid within the capillary to diffusion. The electrode is placed near the first end of the capillary in contact with the reference fluid. The method of operation of the present invention begins with filling the capillary tube with a reference solution. After closing the first end of the capillary, the capillary tube may be fully submerged or partially submerged with the second open end inserted into test fluid. Since the electrode is placed near the first end of the capillary, and since the test fluid may intermingle with the reference fluid through the second open end only by diffusion, this intermingling capillary reference half-cell provides a stable voltage potential for long time periods.

  16. Parallel Block Structured Adaptive Mesh Refinement on Graphics Processing Units

    SciTech Connect

    Beckingsale, D. A.; Gaudin, W. P.; Hornung, R. D.; Gunney, B. T.; Gamblin, T.; Herdman, J. A.; Jarvis, S. A.

    2014-11-17

    Block-structured adaptive mesh refinement is a technique that can be used when solving partial differential equations to reduce the number of zones necessary to achieve the required accuracy in areas of interest. These areas (shock fronts, material interfaces, etc.) are recursively covered with finer mesh patches that are grouped into a hierarchy of refinement levels. Despite the potential for large savings in computational requirements and memory usage without a corresponding reduction in accuracy, AMR adds overhead in managing the mesh hierarchy, adding complex communication and data movement requirements to a simulation. In this paper, we describe the design and implementation of a native GPU-based AMR library, including: the classes used to manage data on a mesh patch, the routines used for transferring data between GPUs on different nodes, and the data-parallel operators developed to coarsen and refine mesh data. We validate the performance and accuracy of our implementation using three test problems and two architectures: an eight-node cluster, and over four thousand nodes of Oak Ridge National Laboratory’s Titan supercomputer. Our GPU-based AMR hydrodynamics code performs up to 4.87× faster than the CPU-based implementation, and has been scaled to over four thousand GPUs using a combination of MPI and CUDA.

  17. Decontamination of steel by melt refining: A literature review

    SciTech Connect

    Ozturk, B.; Fruehan, R.J.

    1994-12-31

    It has been reported that a large amount of metal waste is produced annually by nuclear fuel processing and nuclear power plants. These metal wastes are contaminated with radioactive elements, such as uranium and plutonium. Current Department of Energy guidelines require retrievable storage of all metallic wastes containing transuranic elements above a certain level. Because of high cost, it is important to develop an effective decontamination and volume reduction method for low level contaminated metals. It has been shown by some investigators that a melt refining technique can be used for the processing of the contaminated metal wastes. In this process, contaminated metal is melted wit a suitable flux. The radioactive elements are oxidized and transferred to a slag phase. In order to develop a commercial process it is important to have information on the thermodynamics and kinetics of the removal. Therefore, a literature search was carried out to evaluate the available information on the decontamination uranium and transuranic-contaminated plain steel, copper and stainless steel by melt a refining technique. Emphasis was given to the thermodynamics and kinetics of the removal. Data published in the literature indicate that it is possible to reduce the concentration of radioactive elements to a very low level by the melt refining method. 20 refs.

  18. Mesh refinement for uncertainty quantification through model reduction

    SciTech Connect

    Li, Jing Stinis, Panos

    2015-01-01

    We present a novel way of deciding when and where to refine a mesh in probability space in order to facilitate uncertainty quantification in the presence of discontinuities in random space. A discontinuity in random space makes the application of generalized polynomial chaos expansion techniques prohibitively expensive. The reason is that for discontinuous problems, the expansion converges very slowly. An alternative to using higher terms in the expansion is to divide the random space in smaller elements where a lower degree polynomial is adequate to describe the randomness. In general, the partition of the random space is a dynamic process since some areas of the random space, particularly around the discontinuity, need more refinement than others as time evolves. In the current work we propose a way to decide when and where to refine the random space mesh based on the use of a reduced model. The idea is that a good reduced model can monitor accurately, within a random space element, the cascade of activity to higher degree terms in the chaos expansion. In turn, this facilitates the efficient allocation of computational sources to the areas of random space where they are more needed. For the Kraichnan–Orszag system, the prototypical system to study discontinuities in random space, we present theoretical results which show why the proposed method is sound and numerical results which corroborate the theory.

  19. ,"Kerosene-Type Jet Fuel Sales to End Users Refiner Sales Volumes...

    Energy Information Administration (EIA) (indexed site)

    Kerosene-Type Jet Fuel Sales to End Users Refiner Sales Volumes" ,"Click worksheet name or ... Data for" ,"Data 1","Kerosene-Type Jet Fuel Sales to End Users Refiner Sales ...

  20. RFA-14-0001 - In the Matter of Commonwealth Oil Refining Company...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    RFA-14-0001 - In the Matter of Commonwealth Oil Refining Company, Inc.Commonwealth of Puerto Rico RFA-14-0001 - In the Matter of Commonwealth Oil Refining Company, Inc....

  1. Catalytic hydroprocessing of solvent refined coal to provide a liquid and a solid fuel

    SciTech Connect

    Dabkowski, M.J.; Heck, R.H.; Stein, T.R.

    1980-04-29

    In the hydroprocessing of blends of solvent refined coal and recycle solvent, small pore hydrotreating catalysts cause separation of a solid phase from treating blends containing high concentration of solvent refined coal.

  2. Petroleum Refining Sector (NAICS 324110) Energy and GHG Combustion Emissions Profile, November 2012

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    69 2.4 PETROLEUM REFINING SECTOR (NAICS 324110) 2.4.1. Overview of the Petroleum Refining Manufacturing Sector Petroleum refining is a complex industry that generates a diverse slate of fuel products and petrochemicals, from gasoline to asphalt. Refining requires a range of processing steps, including distillation, cracking, reforming, and treating. Most of these processes are highly reliant on process heating and steam energy. Petroleum refineries are an essential part of the U.S. economy.

  3. Occupational employment survey, booklet of definitions. Petroleum refining, coal products, and related industries

    SciTech Connect

    Not Available

    1992-01-01

    The publication gives occupational definitions for 149 occupations in the petroleum refining, coal products, and related industries.

  4. Optical probe with reference fiber

    DOEpatents

    Da Silva, Luiz B.; Chase, Charles L.

    2006-03-14

    A system for characterizing tissue includes the steps of generating an emission signal, generating a reference signal, directing the emission signal to and from the tissue, directing the reference signal in a predetermined manner relative to the emission signal, and using the reference signal to compensate the emission signal. In one embodiment compensation is provided for fluctuations in light delivery to the tip of the probe due to cable motion.

  5. FAQS Reference Guide- Chemical Processing

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the February 2010 edition of DOE-STD-1176-2010, Chemical Processing Functional Area Qualification Standard.

  6. Desk Reference | Department of Energy

    Office of Environmental Management (EM)

    servicing personnel office and financial management staffs and time and attendance clerks ... DOE Handbook on Recruitment and Retention Incentives This desk reference contains ...

  7. FAQS Reference Guide- Aviation Manager

    Energy.gov [DOE]

    This reference guide addresses the competency statements in the January 2010 edition of DOE-STD-1164-2003 Chg 1, Aviation Safety Officer Functional Area Qualification Standard.

  8. Environmental control technology for mining, milling, and refining thorium

    SciTech Connect

    Weakley, S.A.; Blahnik, D.E.; Young, J.K.; Bloomster, C.H.

    1980-02-01

    The purpose of this report is to evaluate, in terms of cost and effectiveness, the various environmental control technologies that would be used to control the radioactive wastes generated in the mining, milling, and refining of thorium from domestic resources. The technologies, in order to be considered for study, had to reduce the radioactivity in the waste streams to meet Atomic Energy Commission (10 CFR 20) standards for natural thorium's maximum permissible concentration (MPC) in air and water. Further regulatory standards or licensing requirements, either federal, state, or local, were not examined. The availability and cost of producing thorium from domestic resources is addressed in a companion volume. The objectives of this study were: (1) to identify the major waste streams generated during the mining, milling, and refining of reactor-grade thorium oxide from domestic resources; and (2) to determine the cost and levels of control of existing and advanced environmental control technologies for these waste streams. Six potential domestic deposits of thorium oxide, in addition to stockpiled thorium sludges, are discussed in this report. A summary of the location and characteristics of the potential domestic thorium resources and the mining, milling, and refining processes that will be needed to produce reactor-grade thorium oxide is presented in Section 2. The wastes from existing and potential domestic thorium oxide mines, mills, and refineries are identified in Section 3. Section 3 also presents the state-of-the-art technology and the costs associated with controlling the wastes from the mines, mills, and refineries. In Section 4, the available environmental control technologies for mines, mills, and refineries are assessed. Section 5 presents the cost and effectiveness estimates for the various environmental control technologies applicable to the mine, mill, and refinery for each domestic resource.

  9. Cogeneration handbook for the petroleum refining industry. [Contains glossary

    SciTech Connect

    Fassbender, L.L.; Garrett-Price, B.A.; Moore, N.L.; Fassbender, A.G.; Eakin, D.E.; Gorges, H.A.

    1984-03-01

    The decision of whether to cogenerate involves several considerations, including technical, economic, environmental, legal, and regulatory issues. Each of these issues is addressed separately in this handbook. In addition, a chapter is included on preparing a three-phase work statement, which is needed to guide the design of a cogeneration system. In addition, an annotated bibliography and a glossary of terminology are provided. Appendix A provides an energy-use profile of the petroleum refining industry. Appendices B through O provide specific information that will be called out in subsequent chapters.

  10. Changing Trends in the Refining Industry (released in AEO2006)

    Reports and Publications

    2006-01-01

    There have been some major changes in the U.S. refining industry recently, prompted in part by a significant decline in the quality of imported crude oil and by increasing restrictions on the quality of finished products. As a result, high-quality crudes, such as the West Texas Intermediate (WTI) crude that serves as a benchmark for oil futures on the New York Mercantile Exchange (NYMEX), have been trading at record premiums to the OPEC (Organization of the Petroleum Exporting Countries) Basket price.

  11. Archived Reference Building Type: Warehouse

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  12. Archived Reference Building Type: Supermarket

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  13. Archived Reference Building Type: Hospital

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  14. Archived Reference Building Type: Hospital

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  15. Archived Reference Building Type: Warehouse

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  16. REFERENCES

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    FEDERAL LAWS AND REGULATIONS a. Public Law (P.L.) 93-579, Privacy Act of 1974, as amended Title 5 United States Code (U.S.C.) Section 552a. . b. P.L. 104-106, Division E, Clinger ...

  17. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    I Reference case projections for natural gas production This page inTenTionally lefT blank 121 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for natural gas production Table I1. World total natural gas production by region, Reference case, 2012-40 (trillion cubic feet) Region/country Projections Average annual percent change, 2012-40 2012 2020 2025 2030 2035 2040 OECD OECD Americas 31.8 35.7 38.6 42.1 44.6 47.3 1.4 United States a 24.0 28.7

  18. Microsoft Word - references.doc

    Office of Legacy Management (LM)

    References May 2005 2004 Site Environmental Report R-1 References Facemire, D. F., S. I. Guttman, D. R. Osborne, and R. H. Sperger, 1990, "Biological and Ecological Site Characterization of the Feed Materials Production Center," FMPC-SUB 018, prepared for Westinghouse Materials Co. of Ohio, Cincinnati, OH. GeoSyntec, 1996, "Impacted Material Placement Plan, On-site Disposal Facility," 20100-PL-007, Revision 3, PCN 2, Prepared for the Fernald Environmental Management Project,

  19. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    G Projections of petroleum and other liquids production in three cases * Reference * High Oil Price * Low Oil Price This page inTenTionally lefT blank 85 U.S. Energy Information Administration | International Energy Outlook 2016 Projections of petroleum and other liquid fuels production in three cases Table G1. World petroleum and other liquids production by region and country, Reference case, 2011-40 (million barrels per day, unless otherwise noted) Region/country History (estimates)

  20. Safeguards and Security Program References

    Directives, Delegations, and Other Requirements [Office of Management (MA)]

    2005-08-26

    The manual establishes definitions for terms related to the Department of Energy Safeguards and Security (S&S) Program and includes lists of references and acronyms/abbreviations applicable to S&S Program directives. Cancels the Safeguards and Security Glossary of Terms, dated 12-18-95. Current Safeguards and Security Program References can also be found at Safeguards and Security Policy Information Resource (http://pir.pnl.gov/)

  1. NPS Quick Reference Guide | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Quick Reference Guide Jump to: navigation, search OpenEI Reference LibraryAdd to library Legal Document- OtherOther: NPS Quick Reference GuideLegal Abstract NPS Quick Reference...

  2. ENZO: AN ADAPTIVE MESH REFINEMENT CODE FOR ASTROPHYSICS

    SciTech Connect

    Bryan, Greg L.; Turk, Matthew J.; Norman, Michael L.; Bordner, James; Xu, Hao; Kritsuk, Alexei G.; O'Shea, Brian W.; Smith, Britton; Abel, Tom; Wang, Peng; Skillman, Samuel W.; Wise, John H.; Reynolds, Daniel R.; Collins, David C.; Harkness, Robert P.; Kim, Ji-hoon; Kuhlen, Michael; Goldbaum, Nathan; Hummels, Cameron; Collaboration: Enzo Collaboration; and others

    2014-04-01

    This paper describes the open-source code Enzo, which uses block-structured adaptive mesh refinement to provide high spatial and temporal resolution for modeling astrophysical fluid flows. The code is Cartesian, can be run in one, two, and three dimensions, and supports a wide variety of physics including hydrodynamics, ideal and non-ideal magnetohydrodynamics, N-body dynamics (and, more broadly, self-gravity of fluids and particles), primordial gas chemistry, optically thin radiative cooling of primordial and metal-enriched plasmas (as well as some optically-thick cooling models), radiation transport, cosmological expansion, and models for star formation and feedback in a cosmological context. In addition to explaining the algorithms implemented, we present solutions for a wide range of test problems, demonstrate the code's parallel performance, and discuss the Enzo collaboration's code development methodology.

  3. Fuel and oxygen addition for metal smelting or refining process

    DOEpatents

    Schlichting, Mark R.

    1994-01-01

    A furnace 10 for smelting iron ore and/or refining molten iron 20 is equipped with an overhead pneumatic lance 40, through which a center stream of particulate coal 53 is ejected at high velocity into a slag layer 30. An annular stream of nitrogen or argon 51 enshrouds the coal stream. Oxygen 52 is simultaneously ejected in an annular stream encircling the inert gas stream 51. The interposition of the inert gas stream between the coal and oxygen streams prevents the volatile matter in the coal from combusting before it reaches the slag layer. Heat of combustion is thus more efficiently delivered to the slag, where it is needed to sustain the desired reactions occurring there. A second stream of lower velocity oxygen can be delivered through an outermost annulus 84 to react with carbon monoxide gas rising from slag layer 30, thereby adding still more heat to the furnace.

  4. Fuel and oxygen addition for metal smelting or refining process

    DOEpatents

    Schlichting, M.R.

    1994-11-22

    A furnace for smelting iron ore and/or refining molten iron is equipped with an overhead pneumatic lance, through which a center stream of particulate coal is ejected at high velocity into a slag layer. An annular stream of nitrogen or argon enshrouds the coal stream. Oxygen is simultaneously ejected in an annular stream encircling the inert gas stream. The interposition of the inert gas stream between the coal and oxygen streams prevents the volatile matter in the coal from combusting before it reaches the slag layer. Heat of combustion is thus more efficiently delivered to the slag, where it is needed to sustain the desired reactions occurring there. A second stream of lower velocity oxygen can be delivered through an outermost annulus to react with carbon monoxide gas rising from slag layer, thereby adding still more heat to the furnace. 7 figs.

  5. A case study of energy conservation opportunities in copper refining

    SciTech Connect

    Somers, W.E.; Hughen, M.L.; Kurylko, L.; Stone, J.R.

    1982-07-01

    A study of energy usage and distribution in a copper refinery was conducted in an attempt to determine possible cost savings in operations of the plant. The study covered those processes which were the major users of energy, namely, smelting, anode casting, electrolytic refining, steam generation and distribution, and electricity distribution. The study involved obtaining data of mass and energy flows in the refinery; identifying energy conservation opportunities (ECO's); obtaining price, operating costs, and saving potentials; for each conservation measure; and analyzing the economical viability of each conservation proposal. Potential cost savings were found to be substantial in heat recovery from slag and anode furnace hot gases, modification of the central steam supply system, control, and redistribution of electrical loads, insulation of electrolytic tanks, and changes in the atomization of oil.

  6. A comparative assessment of resource efficiency in petroleum refining

    SciTech Connect

    Han, Jeongwoo; Forman, Grant S.; Elgowainy, Amgad; Cai, Hao; Wang, Michael; DiVita, Vincent B.

    2015-03-25

    Because of increasing environmental and energy security concerns, a detailed understanding of energy efficiency and greenhouse gas (GHG) emissions in the petroleum refining industry is critical for fair and equitable energy and environmental policies. To date, this has proved challenging due in part to the complex nature and variability within refineries. In an effort to simplify energy and emissions refinery analysis, we delineated LP modeling results from 60 large refineries from the US and EU into broad categories based on crude density (API gravity) and heavy product (HP) yields. Product-specific efficiencies and process fuel shares derived from this study were incorporated in Argonne National Laboratory’s GREET life-cycle model, along with regional upstream GHG intensities of crude, natural gas and electricity specific to the US and EU regions. The modeling results suggest that refineries that process relatively heavier crude inputs and have lower yields of HPs generally have lower energy efficiencies and higher GHG emissions than refineries that run lighter crudes with lower yields of HPs. The former types of refineries tend to utilize energy-intensive units which are significant consumers of utilities (heat and electricity) and hydrogen. Among the three groups of refineries studied, the major difference in the energy intensities is due to the amount of purchased natural gas for utilities and hydrogen, while the sum of refinery feed inputs are generally constant. These results highlight the GHG emissions cost a refiner pays to process deep into the barrel to produce more of the desirable fuels with low carbon to hydrogen ratio.

  7. A comparative assessment of resource efficiency in petroleum refining

    DOE PAGES [OSTI]

    Han, Jeongwoo; Forman, Grant S.; Elgowainy, Amgad; Cai, Hao; Wang, Michael; DiVita, Vincent B.

    2015-03-25

    Because of increasing environmental and energy security concerns, a detailed understanding of energy efficiency and greenhouse gas (GHG) emissions in the petroleum refining industry is critical for fair and equitable energy and environmental policies. To date, this has proved challenging due in part to the complex nature and variability within refineries. In an effort to simplify energy and emissions refinery analysis, we delineated LP modeling results from 60 large refineries from the US and EU into broad categories based on crude density (API gravity) and heavy product (HP) yields. Product-specific efficiencies and process fuel shares derived from this study weremore » incorporated in Argonne National Laboratory’s GREET life-cycle model, along with regional upstream GHG intensities of crude, natural gas and electricity specific to the US and EU regions. The modeling results suggest that refineries that process relatively heavier crude inputs and have lower yields of HPs generally have lower energy efficiencies and higher GHG emissions than refineries that run lighter crudes with lower yields of HPs. The former types of refineries tend to utilize energy-intensive units which are significant consumers of utilities (heat and electricity) and hydrogen. Among the three groups of refineries studied, the major difference in the energy intensities is due to the amount of purchased natural gas for utilities and hydrogen, while the sum of refinery feed inputs are generally constant. These results highlight the GHG emissions cost a refiner pays to process deep into the barrel to produce more of the desirable fuels with low carbon to hydrogen ratio.« less

  8. A Comparative Assessment of Resource Efficiency in Petroleum Refining

    SciTech Connect

    Han, Jeongwoo; Forman, G; Elgowainy, Amgad; Cai, Hao; Wang, Michael; Divita, V

    2015-10-01

    Because of increasing environmental and energy security concerns, a detailed understanding of energy efficiency and greenhouse gas (GHG) emissions in the petroleum refining industry is critical for fair and equitable energy and environmental policies. To date, this has proved challenging due in part to the complex nature and variability within refineries. In an effort to simplify energy and emissions refinery analysis, we delineated LP modeling results from 60 large refineries from the US and EU into broad categories based on crude density (API gravity) and heavy product (HP) yields. Product-specific efficiencies and process fuel shares derived from this study were incorporated in Argonne National Laboratory's GREET life-cycle model, along with regional upstream GHG intensities of crude, natural gas and electricity specific to the US and EU regions. The modeling results suggest that refineries that process relatively heavier crude inputs and have lower yields of HPs generally have lower energy efficiencies and higher GHG emissions than refineries that run lighter crudes with lower yields of HPs. The former types of refineries tend to utilize energy-intensive units which are significant consumers of utilities (heat and electricity) and hydrogen. Among the three groups of refineries studied, the major difference in the energy intensities is due to the amount of purchased natural gas for utilities and hydrogen, while the sum of refinery feed inputs are generally constant. These results highlight the GHG emissions cost a refiner pays to process deep into the barrel to produce more of the desirable fuels with low carbon to hydrogen ratio. (c) 2015 Argonne National Laboratory. Published by Elsevier Ltd.

  9. Evaluation of tropical channel refinement using MPAS-A aquaplanet simulations: TROPICAL CHANNEL REFINEMENT IN MPAS-A

    DOE PAGES [OSTI]

    Martini, Matus N.; Gustafson, William I.; O'Brien, Travis A.; Ma, Po-Lun

    2015-09-01

    Climate models with variable-resolution grids offer a computationally less expensive way to provide more detailed information at regional scales and increased accuracy for processes that cannot be resolved by a coarser grid. This study uses the Model for Prediction Across Scales–Atmosphere (MPAS22A), consisting of a nonhydrostatic dynamical core and a subset of Advanced Research Weather Research and Forecasting (ARW-WRF) model atmospheric physics that have been modified to include the Community Atmosphere Model version 5 (CAM5) cloud fraction parameterization, to investigate the potential benefits of using increased resolution in an tropical channel. The simulations are performed with an idealized aquaplanet configurationmore » using two quasi-uniform grids, with 30 km and 240 km grid spacing, and two variable-resolution grids spanning the same grid spacing range; one with a narrow (20°S–20°N) and one with a wide (30°S–30°N) tropical channel refinement. Results show that increasing resolution in the tropics impacts both the tropical and extratropical circulation. Compared to the quasi-uniform coarse grid, the narrow-channel simulation exhibits stronger updrafts in the Ferrel cell as well as in the middle of the upward branch of the Hadley cell. The wider tropical channel has a closer correspondence to the 30 km quasi-uniform simulation. However, the total atmospheric poleward energy transports are similar in all simulations. The largest differences are in the low-level cloudiness. The refined channel simulations show improved tropical and extratropical precipitation relative to the global 240 km simulation when compared to the global 30 km simulation. All simulations have a single ITCZ. The relatively small differences in mean global and tropical precipitation rates among the simulations are a promising result, and the evidence points to the tropical channel being an effective method for avoiding the extraneous numerical artifacts seen in earlier

  10. Influence of Alloy and Solidification Parameters on Grain Refinement in Aluminum Weld Metal due to Inoculation

    SciTech Connect

    Schempp, Philipp [BAM, Germany; Tang, Z. [BIAS, Germany; Cross, Carl E. [Los Alamos National Laboratory; Seefeld, T. [BIAS, Germany; Pittner, A. [BAM, Germany; Rethmeier, M. [BAM, Germany

    2012-06-28

    The goals are: (1) Establish how much Ti/B grain refiner is need to completely refine aluminum weld metal for different alloys and different welding conditions; (2) Characterize how alloy composition and solidification parameters affect weld metal grain refinement; and (3) Apply relevant theory to understand observed behavior. Conclusions are: (1) additions of Ti/B grain refiner to weld metal in Alloys 1050, 5083, and 6082 resulted in significant grain refinement; (2) grain refinement was more effective in GTAW than LBW, resulting in finer grains at lower Ti content - reason is limited time available for equiaxed grain growth in LBW (inability to occlude columnar grain growth); (3) welding travel speed did not markedly affect grain size within GTAW and LBW clusters; and (4) application of Hunt CET analysis showed experimental G to be on the order of the critical G{sub CET}; G{sub CET} was consistently higher for GTAW than for LBW.

  11. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    A Reference case projections This page inTenTionally lefT blank 25 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A1. World total primary energy consumption by region, Reference case, 2011-40 (quadrillion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 120.6 118.1 125.7 128.1 130.7 133.8 138.1 0.6 United States a 96.8 94.4 100.8 102.0 102.9 103.8 105.7 0.4

  12. Just the crude oil, please: The oil imports - refining capacity connection

    SciTech Connect

    Not Available

    1994-04-29

    Steep growth has brought crude oil imports converging with the amount of US crude oil production in 1993. Meanwhile, petroleum product imports into the US have been falling because, among other reasons, only a few refiners outside the US can produce refined products to the specifications of environmentally minded US legislators. As refiners have concentrated investment to produce clean fuels only in select facilities, supply and logistical challenges loom closely in the future.

  13. Impact of Environmental Compliance Costs on U.S. Refining Profitability 1995-2001

    Reports and Publications

    2003-01-01

    This report assesses the effects of pollution abatement requirements on the financial performance of U.S. petroleum refining and marketing operations during the 1995 to 2001 period. This study is a follow-up to the October 1997 publication entitled The Impact of Environmental Compliance Costs on U.S. Refining Profitability, that focused on the financial impacts of U.S. refining pollution abatement investment requirements in the 1988 to1995 period.

  14. Appendix A: Reference case projections

    Energy Information Administration (EIA) (indexed site)

    U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A4. World gross domestic product (GDP) by region expressed in market exchange rates, Reference case, 2011-40 (billion 2010 dollars) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 18,006 18,440 22,566 25,585 28,757 32,166 36,120 2.4 United States a 15,021 15,369 18,801 21,295 23,894 26,659 29,898 2.4 Canada 1,662

  15. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    F Reference case projections by end-use sector and country grouping This page inTenTionally lefT blank 63 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections by end-use sector and country grouping Table F1. Total world delivered energy consumption by end-use sector and fuel, 2011-40 (quadrillion Btu) Sector/fuel History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 Residential Liquids 9.1 9.2 10.0 9.8 9.5

  16. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    H Reference case projections for electricity capacity and generation by fuel This page inTenTionally lefT blank 97 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H1. World total installed generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 1,258 1,278

  17. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    9 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A14. World population by region, Reference case, 2011-40 (millions) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 484 489 523 544 564 581 597 0.7 United States a 312 315 334 347 359 370 380 0.7 Canada 34 35 38 39 41 43 44 0.8 Mexico and Chile 137 139 151 158 164 169 173 0.8 OECD Europe 548 550 565 571 576 579 581

  18. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    3 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A8. World nuclear energy consumption by region, Reference case, 2011-40 (billion kilowatthours) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 888 867 902 891 901 900 924 0.2 United States a 790 769 804 808 808 812 833 0.3 Canada 88 89 86 72 72 67 62 -1.3 Mexico and Chile 9 8 12 12 20 20 29 4.5 OECD Europe 861 837

  19. ,"U.S. Sales for Resale, Total Refiner Motor Gasoline Sales Volumes...

    Energy Information Administration (EIA) (indexed site)

    Resale, Total Refiner Motor Gasoline Sales Volumes" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description"," Of Series","Frequency","Latest Data for" ...

  20. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Annual Energy Outlook

    Petroleum Marketing Annual 1999 295 Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State (Thousand Gallons per Day) - Continued...

  1. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    Energy Information Administration (EIA) (indexed site)

    Information Administration Petroleum Marketing Annual 1995 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  2. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    Information Administration Petroleum Marketing Annual 1995 Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type (Cents per Gallon Excluding Taxes) - Continued...

  3. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    Energy Information Administration (EIA) (indexed site)

    AdministrationPetroleum Marketing Annual 1999 401 Table A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District and State, 1984-Present (Cents per Gallon...

  4. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    Information Administration Petroleum Marketing Annual 1995 Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type (Million Gallons per Day) - Continued Year...

  5. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Annual Energy Outlook

    Marketing Annual 1999 421 Table A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) -...

  6. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Annual Energy Outlook

    Marketing Annual 1995 467 Table A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) -...

  7. Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    retail outlets, e.g., sales to agricultural customers, commercial sales, and industrial sales. Source: Energy Information Administration Form EIA-782A, "Refiners'Gas...

  8. EERE Success Story-Refining Bio-Oil alongside Petroleum | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Energy Refining Bio-Oil alongside Petroleum EERE Success Story-Refining Bio-Oil alongside Petroleum April 9, 2013 - 12:00am Addthis W.R. Grace, a leading provider of refining technologies, and Pacific Northwest National Laboratory (PNNL) are co-leading an effort to accelerate the development of technologies that enable the processing of bio-oils in petroleum refineries. The ability to leverage existing petroleum-refining infrastructure to produce "drop-in" biofuels (biofuels that

  9. Environmental regulations and changes in petroleum refining operations

    SciTech Connect

    Lidderdale, T.C.M.

    1996-03-01

    The U.S. petroleum industry has responded to four major new federal rules on motor gasoline product quality in the last 6 years: Phase 1 Summer Volatility (Rvp) Regulation, June 1989; Phase 2 Summer Volatility (Rvp) regulation, May 1992; oxygenated Gasoline, November 1992; and reformulated Gasoline Phase I Simple Model, December 1994. These regulations have generated significant changes in domestic refinery operations, affecting marginal production costs and market prices, refinery yields, and the seasonality of production. Some changes have been dramatic. The price of motor gasoline has increased by as much as 60 {cents}/gal due to regulations. Refinery yields of motor gasoline (refinery output of motor gasoline as a fraction of refinery inputs or total refinery output), which historically peaked in the early summer to meet high summer driving demand, now are highest during the winter months. These changes in domestic refining operations are identified and related to the vapor pressure, oxygenated and reformulated gasoline (RFG) product quality regulations. This analysis uses linear regression equations from the Energy Information Administration`s (EIA) Short-Term Integrated Forecasting System (STIFS). The STIFS model is used for producing forecasts appearing in the EIA`s Short-Term Energy Outlook.

  10. Bioremediation of petroleum wastes from the refining of lubricant oils

    SciTech Connect

    Prince, M.; Sambasivam, Y. )

    1993-02-01

    The results of an initial feasibility study on the bioremediation of sludge are presented. The sludge used in the study was taken from a site containing waste produced during the refining of lubricant oils to which sulfuric acid had been added. The effectiveness of bioremediation was examined using shake flask experiments with indigenous and other bacteria sources and nutrient supplementation. The initial results show limited effectiveness of biological treatment at conditions employing indigenous bacteria and low (2%) sludge concentrations in Bushnell-Haas media. In addition, the indigenous bacteria were seen to degrade the polycyclic aromatic hydrocarbons naphthalene, penanthrene and pyrene which are present at some locations at the site. No apparent degradation of material was seen using conditions of high (30%) sludge concentrations in Bushnell-Haas medium under a variety of conditions. In addition, nutrients were rapidly depleted at these sludge concentrations, with the exception of sulfates which were produced when high sludge concentrations were used. 23 refs., 8 figs., 3 tabs.

  11. Advances in Patch-Based Adaptive Mesh Refinement Scalability

    SciTech Connect

    Gunney, Brian T.N.; Anderson, Robert W.

    2015-12-18

    Patch-based structured adaptive mesh refinement (SAMR) is widely used for high-resolution simu- lations. Combined with modern supercomputers, it could provide simulations of unprecedented size and resolution. A persistent challenge for this com- bination has been managing dynamically adaptive meshes on more and more MPI tasks. The dis- tributed mesh management scheme in SAMRAI has made some progress SAMR scalability, but early al- gorithms still had trouble scaling past the regime of 105 MPI tasks. This work provides two critical SAMR regridding algorithms, which are integrated into that scheme to ensure efficiency of the whole. The clustering algorithm is an extension of the tile- clustering approach, making it more flexible and efficient in both clustering and parallelism. The partitioner is a new algorithm designed to prevent the network congestion experienced by its prede- cessor. We evaluated performance using weak- and strong-scaling benchmarks designed to be difficult for dynamic adaptivity. Results show good scaling on up to 1.5M cores and 2M MPI tasks. Detailed timing diagnostics suggest scaling would continue well past that.

  12. Cosmos++: Relativistic Magnetohydrodynamics on Unstructured Grids with Local Adaptive Refinement

    SciTech Connect

    Anninos, P; Fragile, P C; Salmonson, J D

    2005-05-06

    A new code and methodology are introduced for solving the fully general relativistic magnetohydrodynamic (GRMHD) equations using time-explicit, finite-volume discretization. The code has options for solving the GRMHD equations using traditional artificial-viscosity (AV) or non-oscillatory central difference (NOCD) methods, or a new extended AV (eAV) scheme using artificial-viscosity together with a dual energy-flux-conserving formulation. The dual energy approach allows for accurate modeling of highly relativistic flows at boost factors well beyond what has been achieved to date by standard artificial viscosity methods. it provides the benefit of Godunov methods in capturing high Lorentz boosted flows but without complicated Riemann solvers, and the advantages of traditional artificial viscosity methods in their speed and flexibility. Additionally, the GRMHD equations are solved on an unstructured grid that supports local adaptive mesh refinement using a fully threated oct-tree (in three dimensions) network to traverse the grid hierarchy across levels and immediate neighbors. A number of tests are presented to demonstrate robustness of the numerical algorithms and adaptive mesh framework over a wide spectrum of problems, boosts, and astrophysical applications, including relativistic shock tubes, shock collisions, magnetosonic shocks, Alfven wave propagation, blast waves, magnetized Bondi flow, and the magneto-rotational instability in Kerr black hole spacetimes.

  13. Advances in Patch-Based Adaptive Mesh Refinement Scalability

    DOE PAGES [OSTI]

    Gunney, Brian T.N.; Anderson, Robert W.

    2015-12-18

    Patch-based structured adaptive mesh refinement (SAMR) is widely used for high-resolution simu- lations. Combined with modern supercomputers, it could provide simulations of unprecedented size and resolution. A persistent challenge for this com- bination has been managing dynamically adaptive meshes on more and more MPI tasks. The dis- tributed mesh management scheme in SAMRAI has made some progress SAMR scalability, but early al- gorithms still had trouble scaling past the regime of 105 MPI tasks. This work provides two critical SAMR regridding algorithms, which are integrated into that scheme to ensure efficiency of the whole. The clustering algorithm is an extensionmore » of the tile- clustering approach, making it more flexible and efficient in both clustering and parallelism. The partitioner is a new algorithm designed to prevent the network congestion experienced by its prede- cessor. We evaluated performance using weak- and strong-scaling benchmarks designed to be difficult for dynamic adaptivity. Results show good scaling on up to 1.5M cores and 2M MPI tasks. Detailed timing diagnostics suggest scaling would continue well past that.« less

  14. Draft SPD Supplemental EIS Master Reference List | National Nuclear

    National Nuclear Security Administration (NNSA)

    Security Administration | (NNSA) Draft SPD Supplemental EIS Master Reference List References for Chapters 1 - 5 References for Appendix A References for Appendix B References for Appendix C References for Appendix D References for Appendix E References for Appendix F References for Appendix G References for Appendix H References for Appendix I References for Appendix J References for Summary Learn More SPD SEIS References for Appendix E SPD SEIS References for Appendix F SPD SEIS References

  15. Appendix A: Reference case projections

    Energy Information Administration (EIA) (indexed site)

    U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A1. World total primary energy consumption by region, Reference case, 2011-40 (quadrillion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 120.6 118.1 125.7 128.1 130.7 133.8 138.1 0.6 United States a 96.8 94.4 100.8 102.0 102.9 103.8 105.7 0.4 Canada 14.5 14.5 15.1 15.6 16.3 17.1 18.1 0.8 Mexico and Chile 9.3

  16. Appendix A: Reference case projections

    Energy Information Administration (EIA) (indexed site)

    U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A6. World natural gas consumption by region, Reference case, 2011-40 (trillion cubic feet) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 30.8 31.8 32.8 34.3 36.5 38.2 40.1 0.8 United States a 24.5 25.5 26.1 26.9 28.1 28.8 29.7 0.5 Canada 3.7 3.7 3.9 4.2 4.7 5.2 5.6 1.5 Mexico and Chile 2.6 2.6 2.8 3.2 3.6 4.2 4.8

  17. Energy reference handbook. Third edition

    SciTech Connect

    Not Available

    1985-01-01

    The energy field has exploded since the OPEC oil embargo of 1973. Terms that did not even exist several years ago are now being used. In addition, many words have developed interpretations somewhat different from their commonly accepted meanings. The 3rd Edition of the Energy Reference Handbook records and standardizes these terms in a comprehensive glossary. Special emphasis is placed on providing terms and definitions in the area of alternative fuels-synthetics from coal and oil shale; solar; wind; biomass; geothermal; and more - as well as traditional fossil fuels. In total, more than 3,500 terms, key words, and phrases used daily in energy literature are referenced. In addition to these definitions, conversion tables, diagrams, maps, tables, and charts on various aspects of energy which forecast the reserves of fuel resources, plus other information relevant to energy resources and technologies are found in this reference.

  18. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    1 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for natural gas production Table I1. World total natural gas production by region, Reference case, 2012-40 (trillion cubic feet) Region/country Projections Average annual percent change, 2012-40 2012 2020 2025 2030 2035 2040 OECD OECD Americas 31.8 35.7 38.6 42.1 44.6 47.3 1.4 United States a 24.0 28.7 30.4 32.9 34.0 35.3 1.4 Canada 6.1 5.8 6.6 7.2 7.9 8.6 1.2 Mexico 1.7 1.2 1.5 2.0 2.6 3.3

  19. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    3 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for natural gas production Table I3. World other natural gas production by region, Reference case, 2012-40 (trillion cubic feet) Region/country Projections Average annual percent change, 2012-40 2012 2020 2025 2030 2035 2040 OECD OECD Americas 12.0 9.8 9.5 10.7 10.3 10.3 -0.5 United States a 7.5 6.6 6.5 7.8 7.5 7.5 0.0 Canada 2.8 2.0 1.8 1.7 1.6 1.5 -2.2 Mexico 1.7 1.2 1.2 1.2 1.2 1.2 -1.2

  20. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    5 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections Table A10. World carbon dioxide emissions by region, Reference case, 2011-40 (million metric tons carbon dioxide) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 6,558 6,343 6,569 6,620 6,675 6,769 6,887 0.3 United States a 5,483 5,272 5,499 5,511 5,514 5,521 5,549 0.2 Canada 562 563 557 577 587 621 647 0.5 Mexico and

  1. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    Reference case projections Table A12. World carbon dioxide emissions from natural gas use by region, Reference case, 2011-40 (million metric tons carbon dioxide) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 1,666 1,715 1,766 1,849 1,965 2,063 2,167 0.8 United States a 1,305 1,363 1,394 1,432 1,497 1,538 1,586 0.5 Canada 205 205 213 234 261 287 310 1.5 Mexico and Chile 156 147 158 184 207 238 271 2.2 OECD Europe 1,016 970

  2. Aspects of Western Refining, Inc.'s Proposed Acquisition of Giant Industries, Inc.

    Reports and Publications

    2006-01-01

    Presentation of company-level, non-proprietary data and relevant aggregate data for U.S. refinery capacity and gasoline marketing of Western Refining and Giant Industries to inform discussions of Western Refining Inc.'s proposed acquisition of Giant Industries Inc. for a total of $1.5 billion, which was announced August 28, 2006.

  3. ,"No. 2 Diesel Fuel Sales to End Users Refiner Sales Volumes...

    Energy Information Administration (EIA) (indexed site)

    ... Refiners (Thousand Gallons per Day)","New Mexico No 2 Diesel Retail Sales by Refiners ...17.9,1773.9,,,781.9,,3446.1,296.5,,,,129.9,2030.1,,,,182.8,,416.2,,60.5,369.8,1495.2,,76.6...

  4. HANFORD WASTE MINERALOGY REFERENCE REPORT

    SciTech Connect

    DISSELKAMP RS

    2010-06-29

    This report lists the observed mineral phases present in the Hanford tanks. This task was accomplished by performing a review of numerous reports that used experimental techniques including, but not limited to: x-ray diffraction, polarized light microscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, electron energy loss spectroscopy, and particle size distribution analyses. This report contains tables that can be used as a quick reference to identify the crystal phases observed in Hanford waste.

  5. HANFORD WASTE MINEROLOGY REFERENCE REPORT

    SciTech Connect

    DISSELKAMP RS

    2010-06-18

    This report lists the observed mineral phase phases present in the Hanford tanks. This task was accomplished by performing a review of numerous reports using experimental techniques including, but not limited to: x-ray diffraction, polarized light microscopy, scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, electron energy loss spectroscopy, and particle size distribution analyses. This report contains tables that can be used as a quick reference to identify the crystal phases present observed in Hanford waste.

  6. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    J Kaya Identity factor projections * Carbon dioxide intensity * Energy intensity * GDP per capita * Population This page inTenTionally lefT blank 127 U.S. Energy Information Administration | International Energy Outlook 2016 Kaya Identity factor projections Table J1. World carbon dioxide intensity of energy use by region, Reference case, 2011-40 (metric tons per billion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas

  7. Microgrid cyber security reference architecture.

    SciTech Connect

    Veitch, Cynthia K.; Henry, Jordan M.; Richardson, Bryan T.; Hart, Derek H.

    2013-07-01

    This document describes a microgrid cyber security reference architecture. First, we present a high-level concept of operations for a microgrid, including operational modes, necessary power actors, and the communication protocols typically employed. We then describe our motivation for designing a secure microgrid; in particular, we provide general network and industrial control system (ICS)-speci c vulnerabilities, a threat model, information assurance compliance concerns, and design criteria for a microgrid control system network. Our design approach addresses these concerns by segmenting the microgrid control system network into enclaves, grouping enclaves into functional domains, and describing actor communication using data exchange attributes. We describe cyber actors that can help mitigate potential vulnerabilities, in addition to performance bene ts and vulnerability mitigation that may be realized using this reference architecture. To illustrate our design approach, we present a notional a microgrid control system network implementation, including types of communica- tion occurring on that network, example data exchange attributes for actors in the network, an example of how the network can be segmented to create enclaves and functional domains, and how cyber actors can be used to enforce network segmentation and provide the neces- sary level of security. Finally, we describe areas of focus for the further development of the reference architecture.

  8. Appendix E References | National Nuclear Security Administration

    National Nuclear Security Administration (NNSA)

    E References Crosswalk of Appendix E References to Main DSEIS Reference File name (Main DSEIS) or file name in Appendix E folder DOE (U.S. Department of Energy) 1999. Final ...

  9. Category:Water References | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Water References Jump to: navigation, search Add a new Reference Pages in category "Water References" The following 22 pages are in this category, out of 22 total. A Alaska AS...

  10. Category:Buildings References | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Buildings References Jump to: navigation, search Add a new Reference Pages in category "Buildings References" The following 16 pages are in this category, out of 16 total. B Bureau...

  11. Category:Hydrogen References | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Hydrogen References Jump to: navigation, search Add a new Reference Pages in category "Hydrogen References" The following 6 pages are in this category, out of 6 total. F FERC Order...

  12. Subsurface Knowledge Reference Page | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Subsurface Knowledge Reference Page Subsurface Knowledge Reference Page The below listing provides additional references related to Subsurface & Groundwater Remediation. The references are categorized by documents types (e.g., Strategic Plans, Groundwater Plume Map Booklets, etc.) and under each "document type", there is a list of documents and/or hyperlinks to a reference. The Subsurface Knowledge Reference Page will continue to reflect additional information as it is identified.

  13. Technical Reference for Hydrogen Compatibility of Materials

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    152008 Technical Reference on Hydrogen Compatibility of Materials Austenitc Steels: ... Laboratories Technical Reference on Hydrogen Compatibility of Materials MS-9404 7011 ...

  14. A New Solar Irradiance Reference Spectrum

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    A New Solar Irradiance Reference Spectrum Pilewskie, Peter University of Colorado ... We describe the development of a new solar reference spectrum for radiation and climate ...

  15. Template:ReferenceMaterial | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    - The type of reference material (allowable values include: Journal article, Book, Report, etc.) Documentnumber - The reference material document number or DOI...

  16. Manufacturing Energy and Carbon Footprint References | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Manufacturing Energy and Carbon Footprint References footprintreferences.pdf (309.04 KB) More Documents & Publications 2010 Manufacturing Energy and Carbon Footprints: References ...

  17. Impact of oxygenates on petroleum refining, review and forecast

    SciTech Connect

    Unzelman, G.H.

    1995-09-01

    During the coming decade, oxygenates will continue to impact light oil processing and will steadily change the composition of the US gasoline pool. There are several major driving forces that will sustain the gradual influx of oxygen to US gasoline toward the regulatory limits: (1) the positive environmental characteristics of oxygenated compounds, (2) the high-octane quality of ethers that promote elimination of less desirable hydrocarbons and (3) the competitive need for ultra-clean gasoline to compete with alternatives. From 1995 forward, conventional gasoline will gradually shift to RFG (reformulated gasoline) containing a minimum of 2 wt% oxygen and less aromatics. As a result some processing changes, already in motion in the refining industry, will continue. For example, less severe naphtha reforming and cracking innovations to yield more feed for etherification and alkylation. While alternative fuel and vehicle technology will continue to develop, oxygenates in US gasoline will contribute the major alternative dimension to transportation fuel in the foreseeable future. With RFG, internal-combustion engine emissions will be progressively less toxic and lower in photochemical reactivity. The oxygenate mix will favor methyl ethers in spite of the recent methanol price spike. Ethyl ethers will be used on a more limited basis for specific situations where lower volatility and feedstock economics are an advantage. Downstream blending of ethanol will supplement ethers blended at the refinery in situations where economics are more favorable than refinery ethers. Long-range survival of ethanol, as a direct blending agent or feedstock for refinery ethers, depends on one or more of several factors: future crude oil costs, longevity of subsidies and/or mandates, and new production technology based on cellulose yielding ethanol economically competitive with hydrocarbons.

  18. RAM: a Relativistic Adaptive Mesh Refinement Hydrodynamics Code

    SciTech Connect

    Zhang, Wei-Qun; MacFadyen, Andrew I.; /Princeton, Inst. Advanced Study

    2005-06-06

    The authors have developed a new computer code, RAM, to solve the conservative equations of special relativistic hydrodynamics (SRHD) using adaptive mesh refinement (AMR) on parallel computers. They have implemented a characteristic-wise, finite difference, weighted essentially non-oscillatory (WENO) scheme using the full characteristic decomposition of the SRHD equations to achieve fifth-order accuracy in space. For time integration they use the method of lines with a third-order total variation diminishing (TVD) Runge-Kutta scheme. They have also implemented fourth and fifth order Runge-Kutta time integration schemes for comparison. The implementation of AMR and parallelization is based on the FLASH code. RAM is modular and includes the capability to easily swap hydrodynamics solvers, reconstruction methods and physics modules. In addition to WENO they have implemented a finite volume module with the piecewise parabolic method (PPM) for reconstruction and the modified Marquina approximate Riemann solver to work with TVD Runge-Kutta time integration. They examine the difficulty of accurately simulating shear flows in numerical relativistic hydrodynamics codes. They show that under-resolved simulations of simple test problems with transverse velocity components produce incorrect results and demonstrate the ability of RAM to correctly solve these problems. RAM has been tested in one, two and three dimensions and in Cartesian, cylindrical and spherical coordinates. they have demonstrated fifth-order accuracy for WENO in one and two dimensions and performed detailed comparison with other schemes for which they show significantly lower convergence rates. Extensive testing is presented demonstrating the ability of RAM to address challenging open questions in relativistic astrophysics.

  19. PVWatts Version 1 Technical Reference

    SciTech Connect

    Dobos, A. P.

    2013-10-01

    The NREL PVWatts(TM) calculator is a web application developed by the National Renewable Energy Laboratory (NREL) that estimates the electricity production of a grid-connected photovoltaic system based on a few simple inputs. PVWatts combines a number of sub-models to predict overall system performance, and makes several hidden assumptions about performance parameters. This technical reference details the individual sub-models, documents assumptions and hidden parameters, and explains the sequence of calculations that yield the final system performance estimation.

  20. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    9 U.S. Energy Information Administration | International Energy Outlook 2016 Kaya Identity factor projections Table J3. World gross domestic product (GDP) per capita by region expressed in purchasing power parity, Reference case, 2011-40 (2010 dollars per person) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 38,441 39,055 44,716 48,842 53,114 57,747 63,278 1.7 United States a 48,094 48,865 56,285 61,453 66,639 72,107

  1. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    5 U.S. Energy Information Administration | International Energy Outlook 2016 Projections of petroleum and other liquid fuels production in three cases Table G1. World petroleum and other liquids production by region and country, Reference case, 2011-40 (million barrels per day, unless otherwise noted) Region/country History (estimates) Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OPEC a 36.0 37.4 39.2 41.4 44.6 48.7 52.2 1.2 Middle East 26.2 26.6 29.8

  2. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    7 U.S. Energy Information Administration | International Energy Outlook 2016 Projections of petroleum and other liquid fuels production in three cases Table G3. International other liquid fuels a production by region and country, Reference case, 2011-40 (million barrels per day, unless otherwise noted) Region/country History (estimates) Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OPEC b 3.7 3.8 4.3 4.6 4.8 5.2 5.6 1.3 Natural gas plant liquids 3.6 3.7

  3. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    7 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H1. World total installed generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 1,258 1,278 1,330 1,371 1,436 1,517 1,622 0.9 United States a 1,046 1,063 1,079 1,091 1,133 1,187 1,261 0.6 Canada 133 135

  4. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    7 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H11. World installed other renewable generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 41 42 45 49 52 57 59 1.2 United States a 36 37 39 39 39 40 41 0.4 Canada 4 4 5 8 12 15 16 4.9 Mexico and Chile 1 1

  5. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    9 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H13. World net liquids-fred electricity generation by region and country, 2011-40 (billion kilowatthours) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 88 88 66 37 36 35 35 -3.3 United States a 30 23 18 18 18 18 18 -0.9 Canada 6 7 6 6 6 5 5 -1.0 Mexico and

  6. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    1 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H15. World net coal-fred electricity generation by region and country, 2011-40 (billion kilowatthours) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 1,857 1,630 1,808 1,820 1,786 1,778 1,769 0.3 United States a 1,733 1,514 1,709 1,724 1,713 1,704 1,702 0.4

  7. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    Reference case projections for electricity capacity and generation by fuel Table H17. World net hydroelectric and other renewable electricity generation by region and country, 2011-40 (billion kilowatthours) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 1,004 987 1,278 1,376 1,472 1,598 1,763 2.1 United States a 535 520 704 741 781 848 934 2.1 Canada 398 397 459 491 524 557 606 1.5 Mexico and Chile 71 69 115 144

  8. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    5 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H19. World net wind-powered electricity generation by region and country, 2011-40 (billion kilowatthours) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 142 156 295 327 354 404 460 3.9 United States a 120 141 232 235 245 278 319 3.0 Canada 20 11 39 46 53 60 66

  9. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    7 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H21. World net solar electricity generation by region and country, 2011-40 (billion kilowatthours) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 6 12 57 65 79 96 120 8.7 United States a 6 11 51 59 71 88 110 8.5 Canada 0 0 3 3 4 5 5 10.3 Mexico and Chile 0 0 3

  10. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    9 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H3. World installed natural-gas-fred generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 410 420 455 488 534 584 640 1.5 United States a 358 367 393 409 444 481 525 1.3 Canada 20 20 25 30 36 41 46 3.0

  11. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    1 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H5. World installed nuclear generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 115 117 115 113 115 114 118 0.0 United States a 102 102 101 101 102 102 105 0.1 Canada 13 14 12 10 10 10 9 -1.5 Mexico and

  12. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    3 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H7. World installed hydroelectric generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 171 171 183 187 192 198 210 0.7 United States a 78 78 80 80 80 80 80 0.1 Canada 75 75 83 85 88 90 99 1.0 Mexico and

  13. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    5 U.S. Energy Information Administration | International Energy Outlook 2016 Reference case projections for electricity capacity and generation by fuel Table H9. World installed geothermal generating capacity by region and country, 2011-40 (gigawatts) Region/country History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 3 3 5 7 9 10 11 4.3 United States a 3 3 4 5 7 8 9 4.6 Canada 0 0 0 0 0 0 0 - Mexico and Chile 1 1 1 1 2 2 2 3.3 OECD

  14. Reference electrode for electrolytic cell

    DOEpatents

    Kessie, R.W.

    1988-07-28

    A reference electrode device is provided for a high temperature electrolytic cell used to electrolytically recover uranium from spent reactor fuel dissolved in an anode pool, the device having a glass tube to enclose the electrode and electrolyte and serve as a conductive membrane with the cell electrolyte, and an outer metal tube about the glass tube to serve as a shield and basket for any glass sections broken by handling of the tube to prevent their contact with the anode pool, the metal tube having perforations to provide access between the bulk of the cell electrolyte and glass membrane. 4 figs.

  15. High stability wavefront reference source

    DOEpatents

    Feldman, M.; Mockler, D.J.

    1994-05-03

    A thermally and mechanically stable wavefront reference source which produces a collimated output laser beam is disclosed. The output beam comprises substantially planar reference wavefronts which are useful for aligning and testing optical interferometers. The invention receives coherent radiation from an input optical fiber, directs a diverging input beam of the coherent radiation to a beam folding mirror (to produce a reflected diverging beam), and collimates the reflected diverging beam using a collimating lens. In a class of preferred embodiments, the invention includes a thermally and mechanically stable frame comprising rod members connected between a front end plate and a back end plate. The beam folding mirror is mounted on the back end plate, and the collimating lens mounted to the rods between the end plates. The end plates and rods are preferably made of thermally stable metal alloy. Preferably, the input optical fiber is a single mode fiber coupled to an input end of a second single mode optical fiber that is wound around a mandrel fixedly attached to the frame of the apparatus. The output end of the second fiber is cleaved so as to be optically flat, so that the input beam emerging therefrom is a nearly perfect diverging spherical wave. 7 figures.

  16. High stability wavefront reference source

    DOEpatents

    Feldman, Mark; Mockler, Daniel J.

    1994-01-01

    A thermally and mechanically stable wavefront reference source which produces a collimated output laser beam. The output beam comprises substantially planar reference wavefronts which are useful for aligning and testing optical interferometers. The invention receives coherent radiation from an input optical fiber, directs a diverging input beam of the coherent radiation to a beam folding mirror (to produce a reflected diverging beam), and collimates the reflected diverging beam using a collimating lens. In a class of preferred embodiments, the invention includes a thermally and mechanically stable frame comprising rod members connected between a front end plate and a back end plate. The beam folding mirror is mounted on the back end plate, and the collimating lens mounted to the rods between the end plates. The end plates and rods are preferably made of thermally stable metal alloy. Preferably, the input optical fiber is a single mode fiber coupled to an input end of a second single mode optical fiber that is wound around a mandrel fixedly attached to the frame of the apparatus. The output end of the second fiber is cleaved so as to be optically flat, so that the input beam emerging therefrom is a nearly perfect diverging spherical wave.

  17. An adaptive mesh-moving and refinement procedure for one-dimensional conservation laws

    SciTech Connect

    Biswas, R.; Flaherty, J.E.; Arney, D.C. Rensselaer Polytech. Inst., Troy, NY Military Acad., West Point, NY )

    1993-01-01

    We examine the performance of an adaptive mesh-moving and /or local mesh refinement procedure for the finite difference solution of one-dimensional hyperbolic systems of conservation laws. Adaptive motion of a base mesh is designed to isolate spatially distinct phenomena, and recursive local refinement of the time step and cells of the stationary or moving base mesh is performed in regions where a refinement indicator exceeds a prescribed tolerance. These adaptive procedures are incorporated into a computer code that includes a MacCormack finite difference scheme wih Davis' artificial viscosity model and a discretization error estimate based on Richardson's extrapolation. Experiments are conducted on three problems in order to qualify the advantages of adaptive techniques relative to uniform mesh computations and the relative benefits of mesh moving and refinement. Key results indicate that local mesh refinement, with and without mesh moving, can provide reliable solutions at much lower computational cost than possible on uniform meshes; that mesh motion can be used to improve the results of uniform mesh solutions for a modest computational effort; that the cost of managing the tree data structure associated with refinement is small; and that a combination of mesh motion and refinement reliably produces solutions for the least cost per unit accuracy.

  18. Emergency Responder Radioactive Material Quick Reference Sheet

    Energy.gov [DOE]

    Transportation Emergency Preparedness Program (TEPP) Emergency Responder Radioactive Material Quick Reference Sheet

  19. AVIATION SAFETY OFFICER QUALIFICATION STANDARD REFERENCE GUIDE

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    ......... 1 SCOPE ......SCOPE This reference guide addresses the competency statements in the January 2010 edition ...

  20. AVIATION MANAGER QUALIFICATION STANDARD REFERENCE GUIDE

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    ......... 1 SCOPE ......SCOPE This reference guide addresses the competency statements in the November 2009 ...

  1. Influence of Aluminum Content on Grain Refinement and Strength of AZ31 Magnesium GTA Weld Metal

    SciTech Connect

    Babu, N. Kishore; Cross, Carl E.

    2012-06-28

    The goal is to characterize the effect of Al content on AZ31 weld metal, the grain size and strength, and examine role of Al on grain refinement. The approach is to systematically vary the aluminum content of AZ31 weld metal, Measure average grain size in weld metal, and Measure cross-weld tensile properties and hardness. Conclusions are that: (1) increased Al content in AZ31 weld metal results in grain refinement Reason: higher undercooling during solidification; (2) weld metal grain refinement resulted in increased strength & hardness Reason: grain boundary strengthening; and (3) weld metal strength can be raised to wrought base metal levels.

  2. Fact #676: May 23, 2011 U.S. Refiners Produce about 19 Gallons of Gasoline

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    from a Barrel of Oil | Department of Energy 6: May 23, 2011 U.S. Refiners Produce about 19 Gallons of Gasoline from a Barrel of Oil Fact #676: May 23, 2011 U.S. Refiners Produce about 19 Gallons of Gasoline from a Barrel of Oil A standard U.S. barrel contains 42 gallons of crude oil which yields about 44 gallons of petroleum products. The additional 2 gallons of petroleum products come from refiner gains which result in an additional 6% of product. As shown in the figure below, a little more

  3. FIA-15-0002 - In the Matter of Alon Refining Krotz Springs, Inc. |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy 2 - In the Matter of Alon Refining Krotz Springs, Inc. FIA-15-0002 - In the Matter of Alon Refining Krotz Springs, Inc. This Decision concerns an Appeal that Alon Refining Krotz Springs, Inc. (Alon) filed in response to a determination that was issued to it by the Department of Energy's (DOE) Office of Information Resources (OIR). In that determination, the OIR replied to a request for documents that Alon submitted under the Freedom of Information Act (FOIA), 5 U.S.C. §

  4. Appendix A: Reference case projections

    Energy Information Administration (EIA) (indexed site)

    8 Appendix A Table A3. World gross domestic product (GDP) by region expressed in purchasing power parity, Reference case, 2011-40 (billion 2010 dollars) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 18,616 19,080 23,390 26,577 29,942 33,569 37,770 2.5 United States a 15,021 15,369 18,801 21,295 23,894 26,659 29,898 2.4 Canada 1,396 1,422 1,700 1,881 2,074 2,293 2,529 2.1 Mexico and Chile 2,200 2,288 2,890 3,400 3,974 4,618

  5. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    7 U.S. Energy Information Administration | International Energy Outlook 2016 Kaya Identity factor projections Table J1. World carbon dioxide intensity of energy use by region, Reference case, 2011-40 (metric tons per billion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 53.6 53.0 52.3 51.7 51.1 50.6 49.9 -0.2 United States a 55.7 55.0 54.5 54.0 53.6 53.2 52.5 -0.2 Canada 38.8 38.9 37.0 37.0 36.1 36.2 35.8 -0.3 Mexico

  6. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    30 Appendix J Table J4. World population by region, Reference case, 2011-2040 (millions) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 484 489 523 544 564 581 597 0.7 United States a 312 315 334 347 359 370 380 0.7 Canada 34 35 38 39 41 43 44 0.8 Mexico and Chile 137 139 151 158 164 169 173 0.8 OECD Europe 548 550 565 571 576 579 581 0.2 OECD Asia 203 204 207 208 208 207 206 0.0 Japan 127 127 125 123 120 117 114 -0.4 South

  7. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    6 Appendix A Table A11. World carbon dioxide emissions from liquids use by region, Reference case, 2011-40 (million metric tons carbon dioxide) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 2,881 2,838 2,861 2,812 2,785 2,794 2,812 0.0 United States a 2,291 2,240 2,269 2,227 2,182 2,163 2,147 -0.2 Canada 289 291 291 289 290 295 304 0.2 Mexico and Chile 301 307 301 296 313 335 361 0.6 OECD Europe 1,969 1,903 1,823 1,804

  8. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    8 Appendix A Table A13. World carbon dioxide emissions from coal use by region, Reference case, 2011-40 (million metric tons carbon dioxide) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 2,000 1,779 1,931 1,947 1,912 1,901 1,896 0.2 United States a 1,876 1,657 1,824 1,840 1,822 1,808 1,804 0.3 Canada 68 68 53 54 36 38 33 -2.5 Mexico and Chile 56 54 53 53 54 55 58 0.3 OECD Europe 1,208 1,251 1,228 1,244 1,219 1,195 1,178

  9. Generic Crystalline Disposal Reference Case

    SciTech Connect

    Painter, Scott Leroy; Chu, Shaoping; Harp, Dylan Robert; Perry, Frank Vinton; Wang, Yifeng

    2015-02-20

    A generic reference case for disposal of spent nuclear fuel and high-level radioactive waste in crystalline rock is outlined. The generic cases are intended to support development of disposal system modeling capability by establishing relevant baseline conditions and parameters. Establishment of a generic reference case requires that the emplacement concept, waste inventory, waste form, waste package, backfill/buffer properties, EBS failure scenarios, host rock properties, and biosphere be specified. The focus in this report is on those elements that are unique to crystalline disposal, especially the geosphere representation. Three emplacement concepts are suggested for further analyses: a waste packages containing 4 PWR assemblies emplaced in boreholes in the floors of tunnels (KBS-3 concept), a 12-assembly waste package emplaced in tunnels, and a 32-assembly dual purpose canister emplaced in tunnels. In addition, three failure scenarios were suggested for future use: a nominal scenario involving corrosion of the waste package in the tunnel emplacement concepts, a manufacturing defect scenario applicable to the KBS-3 concept, and a disruptive glaciation scenario applicable to both emplacement concepts. The computational approaches required to analyze EBS failure and transport processes in a crystalline rock repository are similar to those of argillite/shale, with the most significant difference being that the EBS in a crystalline rock repository will likely experience highly heterogeneous flow rates, which should be represented in the model. The computational approaches required to analyze radionuclide transport in the natural system are very different because of the highly channelized nature of fracture flow. Computational workflows tailored to crystalline rock based on discrete transport pathways extracted from discrete fracture network models are recommended.

  10. Recovery Act - Refinement of Cross Flow Turbine Airfoils

    SciTech Connect

    McEntee, Jarlath

    2013-08-30

    Ocean Renewable Power Company, LLC (ORPC) is a global leader in hydrokinetic technology and project development. ORPC develops hydrokinetic power systems and eco-conscious projects that harness the power of oceans and rivers to create clean, predictable renewable energy. ORPC’s technology consists of a family of modular hydrokinetic power systems: the TidGen® Power System, for use at shallow to medium-depth tidal sites; the RivGen™ Power System, for use at river and estuary sites; and the OCGen® Power System, presently under development, for use at deep tidal and offshore ocean current sites. These power systems convert kinetic energy in moving water into clean, renewable, grid-compatible electric power. The core technology component for all ORPC power systems is its patented turbine generator unit (TGU). The TGU uses proprietary advanced design cross flow (ADCF) turbines to drive an underwater permanent magnet generator mounted at the TGU’s center. It is a gearless, direct-drive system that has the potential for high reliability, requires no lubricants and releases no toxins that could contaminate the surrounding water. The hydrokinetic industry shows tremendous promise as a means of helping reduce the U.S.’s use of fossil fuels and dependence on foreign oil. To exploit this market opportunity, cross-flow hydrokinetic devices need to advance beyond the pre-commercial state and more systematic data about the structure and function of cross-flow hydrokinetic devices is required. This DOE STTR project, “Recovery Act - Refinement of Cross Flow Turbine Airfoils,” refined the cross-flow turbine design process to improve efficiency and performance and developed turbine manufacturing processes appropriate for volume production. The project proposed (1) to overcome the lack of data by extensively studying the properties of cross flow turbines, a particularly competitive design approach for extracting hydrokinetic energy and (2) to help ORPC mature its pre

  11. Table A3. Refiner/Reseller Prices of Distillate and Residual...

    Energy Information Administration (EIA) (indexed site)

    A3. RefinerReseller Prices of Distillate and Residual Fuel Oils, by PAD District, 1983-Present (Cents per Gallon Excluding Taxes) Geographic Area Year No. 1 Distillate No. 2...

  12. Process for solvent refining of coal using a denitrogenated and dephenolated solvent

    DOEpatents

    Garg, Diwakar (Macungie, PA); Givens, Edwin N. (Bethlehem, PA); Schweighardt, Frank K. (Allentown, PA)

    1984-01-01

    A process is disclosed for the solvent refining of non-anthracitic coal at elevated temperatures and pressure in a hydrogen atmosphere using a hydrocarbon solvent which before being recycled in the solvent refining process is subjected to chemical treatment to extract substantially all nitrogenous and phenolic constituents from the solvent so as to improve the conversion of coal and the production of oil in the solvent refining process. The solvent refining process can be either thermal or catalytic. The extraction of nitrogenous compounds can be performed by acid contact such as hydrogen chloride or fluoride treatment, while phenolic extraction can be performed by caustic contact or contact with a mixture of silica and alumina.

  13. Table 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil...

    Annual Energy Outlook

    839.2 135.0 1,251.9 See footnotes at end of table. 46. Refiner No. 2 Distillate, Diesel Fuel, and Fuel Oil Volumes by PAD District and State Energy Information Administration ...

  14. Table 13. U.S. Refiner Reformulated Motor Gasoline Volumes by...

    Energy Information Administration (EIA) (indexed site)

    3.3 3.4 7.9 3.3 W 11.3 See footnotes at end of table. 13. U.S. Refiner Reformulated Motor Gasoline Volumes by Grade and Sales Type 26 Energy Information Administration ...

  15. Table 8. U.S. Refiner Conventional Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    88.4 87.8 80.1 70.0 NA 72.6 See footnotes at end of table. 8. U.S. Refiner Conventional Motor Gasoline Prices by Grade and Sales Type 16 Energy Information Administration ...

  16. Table 9. U.S. Refiner Conventional Motor Gasoline Volumes by...

    Energy Information Administration (EIA) (indexed site)

    5.7 5.9 4.4 12.9 NA 17.3 See footnotes at end of table. 9. U.S. Refiner Conventional Motor Gasoline Volumes by Grade and Sales Type 18 Energy Information Administration ...

  17. Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    92.8 92.5 84.0 72.5 W 80.7 See footnotes at end of table. 12. U.S. Refiner Reformulated Motor Gasoline Prices by Grade and Sales Type 24 Energy Information Administration ...

  18. Table 8. U.S. Refiner Conventional Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    87.4 86.9 78.3 68.5 W 70.8 See footnotes at end of table. 8. U.S. Refiner Conventional Motor Gasoline Prices by Grade and Sales Type 16 Energy Information Administration ...

  19. Table 12. U.S. Refiner Reformulated Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    92.4 92.1 83.7 74.1 W 80.9 See footnotes at end of table. 12. U.S. Refiner Reformulated Motor Gasoline Prices by Grade and Sales Type 24 Energy Information Administration ...

  20. Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    98.0 98.0 86.6 75.0 - 80.1 See footnotes at end of table. 10. U.S. Refiner Oxygenated Motor Gasoline Prices by Grade and Sales Type 20 Energy Information Administration ...

  1. Table 10. U.S. Refiner Oxygenated Motor Gasoline Prices by...

    Energy Information Administration (EIA) (indexed site)

    94.0 93.9 83.2 73.8 - 79.3 See footnotes at end of table. 10. U.S. Refiner Oxygenated Motor Gasoline Prices by Grade and Sales Type 20 Energy Information Administration ...

  2. Table 13. U.S. Refiner Reformulated Motor Gasoline Volumes by...

    Energy Information Administration (EIA) (indexed site)

    3.6 3.7 7.9 3.1 W 11.0 See footnotes at end of table. 13. U.S. Refiner Reformulated Motor Gasoline Volumes by Grade and Sales Type 26 Energy Information Administration ...

  3. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    NA 26.6 See footnotes at end of table. 14 Energy Information AdministrationPetroleum Marketing Annual 1999 Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type...

  4. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    NA 27.4 See footnotes at end of table. 14 Energy Information AdministrationPetroleum Marketing Annual 1998 Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type...

  5. Table A2. Refiner/Reseller Prices of Aviation Fuels, Propane...

    Gasoline and Diesel Fuel Update

    - W 73.5 See footnotes at end of table. A2. RefinerReseller Prices of Aviation Fuels, Propane, and Kerosene, by PAD District, 1983-Present Energy Information Administration ...

  6. Table 9. U.S. Refiner Conventional Motor Gasoline Volumes by...

    Energy Information Administration (EIA) (indexed site)

    0.1 18.7 See footnotes at end of table. 18 Energy Information Administration Petroleum Marketing Annual 1995 Table 9. U.S. Refiner Conventional Motor Gasoline Volumes by Grade...

  7. Energy and Environmental Profile of the U.S. Petroleum Refining Industry

    SciTech Connect

    Pellegrino, Joan; Brueske, Sabine; Carole, Tracy; Andres, Howard

    2007-11-01

    This 2007 report provides an overview of the U.S. petroleum refining industry, including new data on market trends and energy and material consumption, as well as information on environmental performance.

  8. Impact of Environmental Compliance Costs on U.S. Refining Profitability

    Reports and Publications

    1997-01-01

    Assesses the effects of pollution abatement requirements on the financial performance of U.S. petroleum refining and marketing operations. The analysis draws heavily on financial and operating data from the Energy Information Administration's Financial Reporting System (FRS).

  9. Fact #676: May 23, 2011 U.S. Refiners Produce about 19 Gallons...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    A standard U.S. barrel contains 42 gallons of crude oil which yields about 44 gallons of ... and 10 gallons of diesel fuel are produced from a barrel of crudeoil by U.S. refiners. ...

  10. Refinements in the Los Alamos model of the prompt fission neutron spectrum

    Office of Scientific and Technical Information (OSTI)

    (Journal Article) | DOE PAGES Published Article: Refinements in the Los Alamos model of the prompt fission neutron spectrum Title: Refinements in the Los Alamos model of the prompt fission neutron spectrum Authors: Madland, D. G. ; Kahler, A. C. Publication Date: 2017-01-01 OSTI Identifier: 1326113 Grant/Contract Number: AC5206NA25396 Type: Published Article Journal Name: Nuclear Physics. A Additional Journal Information: Journal Volume: 957; Journal Issue: C; Related Information: CHORUS

  11. Petroleum movements and investments in the refining industry: The impact of worldwide environmental regulations

    SciTech Connect

    Guariguata U., G.

    1995-09-01

    Since the enactment of the US Clean Air Act Amendments of 1990, the worldwide refining industry has aligned itself to become increasing attuned to the future well-being of the environment. Refiners must now develop strategies which address careful selection of crude slates, significant increases and changes in product movements, and upgrading of facilities to meet growing demand--in short, strategies which allow them to make substantial increases in capital investments. The objective of this paper is to determine the regional capital investments refiners must make in order to comply with environmental legislation. The methodology in making this determination was founded on a comprehensive analysis of worldwide petroleum supply/demand and distribution patterns for the coming five years, and included evaluation of a set of linear programming (LP) models based on forecasts for regional product demands and projections of regional specifications. The models considered two scenarios, in which either (1) refinery expansion occurs chiefly in the market consuming regions, or (2) crude producers take control of incremental crude volumes and further expand their planned refining projects and the marketing of refined products. The results of these models, coupled with an understanding of geopolitical situations and economic analyses, provided estimates for capital expenditures for the coming decade. In specific, the following issues were addressed, and are discussed in this paper: refined product trade outlook; crude supply; crude quality; shipping; and capital investments.

  12. Research Notes and Information References

    Energy Science and Technology Software Center

    1994-12-01

    The RNS (Research Notes System) is a set of programs and databases designed to aid the research worker in gathering, maintaining, and using notes taken from the literature. The sources for the notes can be books, journal articles, reports, private conversations, conference papers, audiovisuals, etc. The system ties the databases together in a relational structure, thus eliminating data redundancy while providing full access to all the information. The programs provide the means for access andmore » data entry in a way that reduces the key-entry burden for the user. Each note has several data fields. Included are the text of the note, the subject classification (for retrieval), and the reference identification data. These data are divided into four databases: Document data - title, author, publisher, etc., fields to identify the article within the document; Note data - text and page of the note; Sublect data - subject categories to ensure uniform spelling for searches. Additionally, there are subsidiary files used by the system, including database index and temporary work files. The system provides multiple access routes to the notes, both structurally (access method) and topically (through cross-indexing). Output may be directed to a printer or saved as a file for input to word processing software.« less

  13. Appendix A: Reference case projections

    Energy Information Administration (EIA) (indexed site)

    6 Appendix A Table A2. World total energy consumption by region and fuel, Reference case, 2011-40 (quadrillion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas Liquids 45.3 44.6 46.4 46.1 46.0 46.2 46.7 0.2 Natural gas 31.8 32.8 33.9 35.5 37.7 39.5 41.4 0.8 Coal 21.0 18.7 20.3 20.5 20.1 20.0 20.0 0.2 Nuclear 9.4 9.2 9.5 9.4 9.5 9.5 9.7 0.2 Other 13.1 12.9 15.6 16.6 17.5 18.6 20.3 1.6 Total 120.6 118.1 125.7 128.1 130.7

  14. Appendix A: Reference case projections

    Energy Information Administration (EIA) (indexed site)

    30 Appendix A Table A5. World liquids consumption by region, Reference case, 2011-40 (million barrels per day) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 23.6 23.2 24.4 24.4 24.3 24.4 24.6 0.2 United States a 18.9 18.5 19.6 19.6 19.4 19.3 19.3 0.2 Canada 2.3 2.4 2.4 2.4 2.4 2.4 2.5 0.2 Mexico and Chile 2.4 2.4 2.4 2.4 2.5 2.7 2.9 0.6 OECD Europe 14.5 14.1 13.7 13.6 13.7 13.8 14.0 0.0 OECD Asia 7.9 8.2 7.7 7.5 7.5 7.5

  15. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    8 Appendix J Table J2. World energy intensity by region, Reference case, 2011-40 (thousand Btu per 2010 dollar of GDP) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 6.5 6.2 5.4 4.8 4.4 4.0 3.7 -1.9 United States a 6.4 6.1 5.4 4.8 4.3 3.9 3.5 -2.0 Canada 10.4 10.2 8.9 8.3 7.8 7.5 7.1 -1.3 Mexico and Chile 4.2 4.0 3.4 3.1 2.9 2.8 2.7 -1.4 OECD Europe 4.4 4.4 3.9 3.7 3.5 3.3 3.2 -1.1 OECD Asia 5.7 5.5 5.4 5.3 5.1 4.9 4.8 -0.5

  16. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    86 Appendix G Table G2. World crude oil a production by region and country, Reference case, 2011-40 (million barrels per day, unless otherwise noted) Region/country History (estimates) Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OPEC b 32.2 33.4 34.9 36.8 39.7 43.4 46.6 1.2 Middle East 22.9 23.2 26.2 27.9 30.3 33.4 35.6 1.5 North Africa 2.0 2.9 1.6 1.7 1.8 2.0 2.2 -1.0 West Africa 4.3 4.3 4.3 4.3 4.5 4.7 5.1 0.6 South America 3.0 3.0 2.8 2.9 3.1 3.4 3.6

  17. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    2 Appendix I Table I2. World tight gas, shale gas and coalbed methane production by region, Reference case, 2012-40 (trillion cubic feet) Region/country Projections Average annual percent change, 2012-40 2012 2020 2025 2030 2035 2040 OECD OECD Americas 19.8 26.0 29.0 31.4 34.3 37.0 2.3 United States a 16.6 22.1 23.9 25.1 26.5 27.8 1.9 Canada 3.3 3.8 4.9 5.5 6.3 7.0 2.8 Mexico 0.0 0.1 0.3 0.8 1.4 2.2 - Chile 0.0 0.0 0.0 0.0 0.0 0.0 - OECD Europe 0.0 0.5 1.7 3.3 4.6 5.5 21.8 North Europe 0.0 0.5

  18. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    4 Appendix I Table I4. World net trade in natural gas by region, Reference case, 2012-40 (trillion cubic feet) Region/country Projections Average annual percent change, 2012-40 2012 2020 2025 2030 2035 2040 OECD OECD Americas 0.3 -2.6 -4.0 -5.4 -6.2 -6.9 - United States a 1.5 -2.6 -3.5 -4.8 -5.2 -5.6 - Canada -2.3 -1.9 -2.3 -2.4 -2.7 -2.8 0.7 Mexico 1.0 1.7 1.7 1.6 1.5 1.3 1.1 Chile 0.1 0.1 0.1 0.2 0.2 0.2 1.7 OECD Europe 7.8 10.9 11.9 12.7 13.0 14.0 2.1 North Europe 2.4 5.2 5.9 6.1 6.1 6.3 3.5

  19. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    2 Appendix A Table A7. World coal consumption by region, Reference case, 2011-40 (quadrillion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 21.0 18.7 20.3 20.5 20.1 20.0 20.0 0.2 United States a 19.6 17.3 19.2 19.3 19.2 19.0 19.0 0.3 Canada 0.7 0.7 0.6 0.6 0.4 0.4 0.4 -2.5 Mexico and Chile 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.3 OECD Europe 12.9 13.4 13.2 13.3 13.1 12.8 12.6 -0.2 OECD Asia 9.7 9.7 10.2 10.1 10.1 10.1 10.1 0.1

  20. Appendix A: Reference case projections

    Gasoline and Diesel Fuel Update

    4 Appendix A Table A9. World consumption of hydroelectricity and other renewable energy by region, Reference case, 2011-40 (quadrillion Btu) Region History Projections Average annual percent change, 2012-40 2011 2012 2020 2025 2030 2035 2040 OECD OECD Americas 13.1 12.9 15.6 16.6 17.5 18.6 20.3 1.6 United States a 7.9 7.7 9.3 9.7 9.9 10.4 11.3 1.4 Canada 4.3 4.2 4.8 5.1 5.5 5.8 6.3 1.4 Mexico and Chile 0.9 1.0 1.5 1.8 2.1 2.4 2.7 3.7 OECD Europe 10.7 11.5 15.7 16.7 17.3 18.5 19.6 1.9 OECD Asia

  1. Form:Reference | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    The reference title should match the book title. e.g.- Where the Wild Things Are Book Review Used when citing a review of a book. The reference title should include "Review of the...

  2. Grain refinement of permanent mold cast copper base alloys. Final report

    SciTech Connect

    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M.

    2004-04-29

    Grain refinement behavior of copper alloys cast in permanent molds was investigated. This is one of the least studied subjects in copper alloy castings. Grain refinement is not widely practiced for leaded copper alloys cast in sand molds. Aluminum bronzes and high strength yellow brasses, cast in sand and permanent molds, were usually fine grained due to the presence of more than 2% iron. Grain refinement of the most common permanent mold casting alloys, leaded yellow brass and its lead-free replacement EnviroBrass III, is not universally accepted due to the perceived problem of hard spots in finished castings and for the same reason these alloys contain very low amounts of iron. The yellow brasses and Cu-Si alloys are gaining popularity in North America due to their low lead content and amenability for permanent mold casting. These alloys are prone to hot tearing in permanent mold casting. Grain refinement is one of the solutions for reducing this problem. However, to use this technique it is necessary to understand the mechanism of grain refinement and other issues involved in the process. The following issues were studied during this three year project funded by the US Department of Energy and the copper casting industry: (1) Effect of alloying additions on the grain size of Cu-Zn alloys and their interaction with grain refiners; (2) Effect of two grain refining elements, boron and zirconium, on the grain size of four copper alloys, yellow brass, EnviroBrass II, silicon brass and silicon bronze and the duration of their effect (fading); (3) Prediction of grain refinement using cooling curve analysis and use of this method as an on-line quality control tool; (4) Hard spot formation in yellow brass and EnviroBrass due to grain refinement; (5) Corrosion resistance of the grain refined alloys; (6) Transfer the technology to permanent mold casting foundries; It was found that alloying elements such as tin and zinc do not change the grain size of Cu-Zn alloys

  3. Functional Area Qualification Standard Reference Guides

    Energy.gov [DOE]

    The reference guides have been developed to address the competency statements in DOE Functional Area Qualification Standard.

  4. Commercial Reference Buildings | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Reference Buildings Commercial Reference Buildings The U.S. Department of Energy (DOE), in conjunction with three of its national laboratories, developed commercial reference buildings, formerly known as commercial building benchmark models. These reference buildings play a critical role in the program's energy modeling software research by providing complete descriptions for whole building energy analysis using EnergyPlus simulation software. There are 16 building types that represent

  5. OSTIblog Articles in the reference linking Topic | OSTI, US Dept...

    Office of Scientific and Technical Information (OSTI)

    reference linking Topic OSTI and Reference Linking by Daphne Evans 13 May, 2008 in Technology OSTI actively supports the practice of Reference Linking. Also referred to as citation ...

  6. Research Highlight

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Continuous Clear-Sky Longwave from Surface Measurements Download a printable PDF Submitter: Long, C. N., NOAA Global Monitoring Division/CIRES Turner, D. D., National Oceanic and Atmospheric Administration Area of Research: Radiation Processes Working Group(s): Radiative Processes Journal Reference: Long, CN, and DD Turner. 2008. "A method for continuous estimation of clear-sky downwelling longwave radiative flux developed using ARM surface measurements." Journal of Geophysical

  7. Economic incentives for US refiners to process incremental domestic heavy crude oil

    SciTech Connect

    Guillermo, G.U.

    1995-12-31

    Faced with declining domestic crude supplies and increasing refined product demands, U.S. refiners devote a great deal of attention to securing alternate sources of crude oil. In addition to the traditional and cost-effective choice of imports, a potentially viable source is domestic heavy crude oil. Working with the U.S. Department of Energy and its contractor, the National Institute for Petroleum and Energy Research, Bonner & Moore undertook a project to ascertain the necessary adjustments U.S. refiners would need to make in order to process incremental amounts of heavy crude oil added to domestic refining slates between now and 2010. Results of this study indicated that significant economic investments would be required in order to process these crudes; processing of lighter imports, however, would remain substantially less costly. It would seem, then, that U.S. refiners would elect to process imports over incremental domestic heavy crudes unless they were offered some type of economic incentive to process the heavy oil. This paper addresses the issue of what those economic incentives could be.

  8. Need for refining capacity creates opportunities for producers in Middle East

    SciTech Connect

    Ali, M.S.S. )

    1994-07-11

    Oil industry interest in refining has revived in the past few years in response to rising oil consumption. The trend creates opportunities, for countries in the Middle East, which do not own refining assets nearly in proportion to their crude oil reserved. By closing this gap between reserves and refining capacity, the countries can ease some of the instability now characteristic of the oil market. Some major oil producing countries have begun to move downstream. During the 1980s, Venezuela, Kuwait, Saudi Arabia, Libya, and other members of the Organization of Petroleum Exporting Countries acquired refining assets through direct total purchase or joint ventures. Nevertheless, the oil industry remains largely unintegrated, with the Middle East holding two thirds of worldwide oil reserves but only a small share downstream. As worldwide refining capacity swings from a period of surplus toward one in which the need for new capacity will be built. The paper discusses background of the situation, shrinking surplus, investment requirements, sources of capital, and shipping concerns.

  9. An adaptive grid refinement strategy for the simulation of negative streamers

    SciTech Connect

    Montijn, C. . E-mail: carolynne.montijn@cwi.nl; Hundsdorfer, W. . E-mail: willem.hundsdorfer@cwi.nl; Ebert, U. . E-mail: ute.ebert@cwi.nl

    2006-12-10

    The evolution of negative streamers during electric breakdown of a non-attaching gas can be described by a two-fluid model for electrons and positive ions. It consists of continuity equations for the charged particles including drift, diffusion and reaction in the local electric field, coupled to the Poisson equation for the electric potential. The model generates field enhancement and steep propagating ionization fronts at the tip of growing ionized filaments. An adaptive grid refinement method for the simulation of these structures is presented. It uses finite volume spatial discretizations and explicit time stepping, which allows the decoupling of the grids for the continuity equations from those for the Poisson equation. Standard refinement methods in which the refinement criterion is based on local error monitors fail due to the pulled character of the streamer front that propagates into a linearly unstable state. We present a refinement method which deals with all these features. Tests on one-dimensional streamer fronts as well as on three-dimensional streamers with cylindrical symmetry (hence effectively 2D for numerical purposes) are carried out successfully. Results on fine grids are presented, they show that such an adaptive grid method is needed to capture the streamer characteristics well. This refinement strategy enables us to adequately compute negative streamers in pure gases in the parameter regime where a physical instability appears: branching streamers.

  10. OPTICAL SPECTRA OF CANDIDATE SOUTHERN HEMISPHERE INTERNATIONAL CELESTIAL REFERENCE FRAME (ICRF) RADIO SOURCES

    SciTech Connect

    Titov, O.; Jauncey, D. L.; Johnston, H. M.; Hunstead, R. W.; Christensen, L.

    2011-11-15

    We present the results of spectroscopic observations of the optical counterparts of 47 southern radio sources from the candidate International Celestial Reference Catalogue as part of a very long baseline interferometry (VLBI) program to strengthen the celestial reference frame, especially in the south. We made the observations with the 3.58 m European Southern Observatory New Technology Telescope. We obtained redshifts for 30 quasars and one radio galaxy, with a further seven objects being probable BL Lac objects with featureless spectra. Of the remainder, four were clear misidentifications with Galactic stars and five had low signal-to-noise spectra and could not be classified. These results, in combination with new VLBI data of the radio sources with redshifts more than 2, add significantly to the existing data needed to refine the distribution of source proper motions over the celestial sphere.

  11. Adaptive h -refinement for reduced-order models: ADAPTIVE h -refinement for reduced-order models

    SciTech Connect

    Carlberg, Kevin T.

    2014-11-05

    Our work presents a method to adaptively refine reduced-order models a posteriori without requiring additional full-order-model solves. The technique is analogous to mesh-adaptive h-refinement: it enriches the reduced-basis space online by ‘splitting’ a given basis vector into several vectors with disjoint support. The splitting scheme is defined by a tree structure constructed offline via recursive k-means clustering of the state variables using snapshot data. This method identifies the vectors to split online using a dual-weighted-residual approach that aims to reduce error in an output quantity of interest. The resulting method generates a hierarchy of subspaces online without requiring large-scale operations or full-order-model solves. Furthermore, it enables the reduced-order model to satisfy any prescribed error tolerance regardless of its original fidelity, as a completely refined reduced-order model is mathematically equivalent to the original full-order model. Experiments on a parameterized inviscid Burgers equation highlight the ability of the method to capture phenomena (e.g., moving shocks) not contained in the span of the original reduced basis.

  12. Refining of fossil resin flotation concentrate from western coal. Final report

    SciTech Connect

    Jensen, G.F.; Miller, J.D.

    1995-02-16

    During the past several years, significant research efforts have been made to develop process technology for the selective flotation of fossil resin from western coals. As a result of these efforts, several new flotation technologies have been developed. Operation of a proof-of-concept continuous flotation circuit showed the selective flotation process to be sufficiently profitable to justify the development of a fossil resin industry. However, little attention has been given to the refining of the fossil resin flotation concentrate although solvent refining is a critical step for the fossil resin to become a marketable product. In view of this situation, DOE funded this two-year project to evaluate the following aspects of the fossil resin refining technology: 1) Characterization of the fossil resin flotation concentrate and its refined products; 2) Kinetics of fossil resin extraction; 3) Effects of operating variables on solvent extraction; 4) Extraction solvents; 5) Proof-of-concept continuous refining tests; and 6) Technical and economic analysis. The results from this research effort have led to the following conclusions: Hexane- or heptane-refined fossil resin has a light-yellow color, a melting point of 140 - 142{degrees}C, a density of 1.034 gram/cm, and good solubility in nonpolar solvents. Among the four solvents evaluated (hexane, heptane, toluene and ethyl acetate), hexane is the most appropriate solvent based on overall technical and economic considerations. Batch extraction tests and kinetic studies suggest that the main interaction between the resin and the solvent is expected to be the forces associated with solvation phenomena. Temperature has the most significant effect on extraction rate. With hexane as the solvent, a recovery of 90% cam be achieved at 50{degrees}C and 10% solids concentration with moderate agitation for 1 hour.

  13. Free kick instead of cross-validation in maximum-likelihood refinement of macromolecular crystal structures

    SciTech Connect

    Pranikar, Jure [Institute Joef Stefan, Jamova 39, 1000 Ljubljana (Slovenia); University of Primorska, (Slovenia); Turk, Duan, E-mail: dusan.turk@ijs.si [Institute Joef Stefan, Jamova 39, 1000 Ljubljana (Slovenia); Center of Excellence for Integrated Approaches in Chemistry and Biology of Proteins, (Slovenia)

    2014-12-01

    The maximum-likelihood free-kick target, which calculates model error estimates from the work set and a randomly displaced model, proved superior in the accuracy and consistency of refinement of crystal structures compared with the maximum-likelihood cross-validation target, which calculates error estimates from the test set and the unperturbed model. The refinement of a molecular model is a computational procedure by which the atomic model is fitted to the diffraction data. The commonly used target in the refinement of macromolecular structures is the maximum-likelihood (ML) function, which relies on the assessment of model errors. The current ML functions rely on cross-validation. They utilize phase-error estimates that are calculated from a small fraction of diffraction data, called the test set, that are not used to fit the model. An approach has been developed that uses the work set to calculate the phase-error estimates in the ML refinement from simulating the model errors via the random displacement of atomic coordinates. It is called ML free-kick refinement as it uses the ML formulation of the target function and is based on the idea of freeing the model from the model bias imposed by the chemical energy restraints used in refinement. This approach for the calculation of error estimates is superior to the cross-validation approach: it reduces the phase error and increases the accuracy of molecular models, is more robust, provides clearer maps and may use a smaller portion of data for the test set for the calculation of R{sub free} or may leave it out completely.

  14. References | National Nuclear Security Administration | (NNSA)

    National Nuclear Security Administration (NNSA)

    References U.S. Department of Energy / U.S. Nuclear Regulatory Commission Nuclear Materials Management & Safeguards System References Additional information related to the NMMSS may be located in the publications listed below. By referencing these documents, a more extensive understanding of the system may be gained. Other references extracted from DOE M 470.4-6 and used within the industry have also been included. "Agreement between the United States of America and the IAEA for the

  15. Existing Commercial Reference Buildings Constructed Before 1980 |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Before 1980 Existing Commercial Reference Buildings Constructed Before 1980 The files on this page contain commercial reference building models for existing buildings constructed before 1980, organized by building type and location. These U.S. Department of Energy (DOE) reference buildings are complete descriptions for whole building energy analysis. You can also return to a summary of building types and climate zones and information about other building vintages. These

  16. New Seismic Model Will Refine Hazard Analysis at U.S. Nuclear Plants |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Seismic Model Will Refine Hazard Analysis at U.S. Nuclear Plants New Seismic Model Will Refine Hazard Analysis at U.S. Nuclear Plants January 31, 2012 - 2:09pm Addthis The Electric Power Research Institute (EPRI), the U.S. Department of Energy (DOE), and the U.S. Nuclear Regulatory Commission (NRC) released a new seismic study today that will help U.S. nuclear facilities in the central and eastern United States reassess seismic hazards. The Central and Eastern United

  17. Appendices: Steam System Opportunity Assessment for the Pulp and Paper, Chemical Manufacturing, and Petroleum Refining Industries

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    DE P A R T M E N U E N I T E D S T A T S O F A E R IC A M Office of Energy Efficency and Renewable Energy U.S. Department of Energy Steam System Opportunity Assessment for the Pulp and Paper, Chemical Manufacturing, and Petroleum Refining Industries Steam System Opportunity Assessment for the Pulp and Paper, Chemical Manufacturing, and Petroleum Refining Industries Appendices Appendices (This page intentionally left blank.) Steam System Opportunity Assessment for the Pulp and Paper, Chemical

  18. ,"U.S. Aviation Gasoline Refiner Sales Volumes"

    Energy Information Administration (EIA) (indexed site)

    Aviation Gasoline Refiner Sales Volumes" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Aviation Gasoline Refiner Sales Volumes",2,"Monthly","8/2016","1/15/1983" ,"Release Date:","11/1/2016" ,"Next Release Date:","12/1/2016" ,"Excel File

  19. ,"U.S. Residual Fuel Oil Refiner Sales Volumes"

    Energy Information Administration (EIA) (indexed site)

    Refiner Sales Volumes" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Residual Fuel Oil Refiner Sales Volumes",2,"Monthly","8/2016","1/15/1983" ,"Release Date:","11/1/2016" ,"Next Release Date:","12/1/2016" ,"Excel File

  20. ,"U.S. Total Refiner Acquisition Cost of Crude Oil"

    Energy Information Administration (EIA) (indexed site)

    Refiner Acquisition Cost of Crude Oil" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Total Refiner Acquisition Cost of Crude Oil",3,"Annual",2015,"6/30/1968" ,"Release Date:","11/1/2016" ,"Next Release Date:","12/1/2016" ,"Excel File

  1. ORISE: Radiological Terms Quick Reference Guide

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Type text Type text Type text Radiation Emergency Assistance CenterTraining Site ... 2015 Quick Reference Information - Radiation Activity: Radioactive materials aren't ...

  2. FAQS Reference Guide – Environmental Compliance

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the June 2011 edition of DOE-STD-1156-2011, Environmental Compliance Functional Area Qualification Standard.

  3. FAQS Reference Guide – Emergency Management

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the January 2004 edition of DOE-STD-1177-2004, Emergency Management Functional Area Qualification Standard.

  4. Reference Form | SREL REU in Radioecology

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    to highlight specific examples that illustrate the candidate's strengths or suitability to the program. Therefore, we also require references to also upload a letter of...

  5. FAQS Reference Guide – Criticality Safety (NNSA)

    Energy.gov [DOE]

    This reference guide has been developed to address the competency statements in DOE-STD-1173-2009, Criticality Safety Functional Area Qualification Standard.

  6. FAQS Reference Guide – Technical Training

    Energy.gov [DOE]

    This reference guide addresses the competency statements in the February 2004 edition of DOE-STD-1179-2004, Technical Training Functional Area Qualification Standard.

  7. FAQS Reference Guide – Facility Representative

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the October 2010 edition of DOE-STD-1151-2010, Facility Representative Functional Area Qualification Standard.

  8. Template:Reference | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    for references that may not require listed authors such as technical reports or web referenced material (Report & Web Site) GraphicAuthor - List of authors or map...

  9. Floating Oscillating Water Column Reference Model Completed

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Floating Oscillating Water Column Reference Model Completed - Sandia Energy Energy Search ... Energy Conversion Efficiency Solar Energy Wind Energy Water Power Supercritical CO2 ...

  10. Commercial Reference Buildings | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Reference Building Types1 , which represent approximately 70% of the commercial buildings in the U.S. 2. Whole building energy analysis data (developed using EnergyPlus...

  11. FAQS Reference Guide – Industrial Hygiene

    Energy.gov [DOE]

    This reference guide addresses the competency statements in the November 2007 edition of DOE-STD-1138-2007, Industrial Hygiene Functional Area Qualification Standard.

  12. Multiple Reference Fourier Transform Holography: Five Images...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Multiple Reference Fourier Transform Holography: Five Images for the Price of One ... Our technique uses coherent x-ray scattering to simultaneously acquire multiple images of ...

  13. Property:ReferenceGenre | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Property Type Text Description The genre or subcategory label of reference material. Allows Values Buildings;Bulk Transmission;Geothermal;Hydrogen;Hydropower;Smart...

  14. FAQS Reference Guide – Construction Management

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the March 2004 edition of DOE-STD-1180-2004, Construction Management Functional Area Qualification Standard.

  15. FAQS Reference Guide – Fire Protection Engineering

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the December 2007 edition of DOE-STD-1137-2007, Fire Protection Engineering Functional Area Qualification Standard.

  16. IBM References | Argonne Leadership Computing Facility

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Feedback Form IBM References Contents IBM Redbooks A2 Processor Manual QPX Vector Instruction Set Architecture XL Compiler Documentation MASS Documentation Back to top IBM...

  17. FAQS Reference Guide – Criticality Safety

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide addresses the competency statements in the April 2009 edition of DOE-STD-1173-2009, Criticality Safety Functional Area Qualification Standard.

  18. Manufacturing Energy and Carbon Footprint References

    Energy.gov [DOE] (indexed site)

    References AMO (Advanced Manufacturing Office), EERE (Energy Efficiency and Renewable Energy). 2012. Consider Installing High-Pressure Boilers with Backpressure Turbine-Generators. ...

  19. EERE Program Management Quick Reference Guide

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    a companion to the Office of Energy Efficiency and Renewable Energy (EERE) Program Management Reference Guide. It provides an overall description of the EERE program management ...

  20. Reference Designs for Hydrogen Fueling Stations Webinar

    Energy.gov [DOE]

    Access the recording and download the presentation slides from the Fuel Cell Technologies Office webinar "Reference Designs for Hydrogen Fueling Stations" held on October 13, 2015.

  1. Studies on design of a process for organo-refining of coal to obtain super clean coal

    SciTech Connect

    Sharma, C.S.; Sharma, D.K.

    1999-08-01

    Organo-refining of coal results in refining the coal to obtain super clean coal and residual coal. Super clean coal may be used to obtain value added chemicals, products, and cleaner fuels from coal. In the present work, studies on the design of a semicontinuous process for organo-refining of one ton of coal have been made. The results are reported. This is only a cursory attempt for the design, and further studies may be required for designing this process for use in the development of a scaled-up process of organo-refining of coal.

  2. Archived Reference Building Type: Large Hotel

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  3. Archived Reference Building Type: Quick service restaurant

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  4. Archived Reference Building Type: Quick service restaurant

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  5. Archived Reference Building Type: Full service restaurant

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  6. Archived Reference Building Type: Full service restaurant

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  7. Archived Reference Climate Zone: 8 Fairbanks, Alaska

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zonesis available for reference.Current versionsare also available.

  8. Archived Reference Climate Zone: 8 Fairbanks, Alaska

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  9. References - DOE Directives, Delegations, and Requirements

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    References by Website Administrator This page provides information and links to references. Technical Standards Technical Standards Program Technical Standards Home RevCom for Technical Standards Technical Standards Crosswalk NNSA Directives National Nuclear Security Administration (NNSA) Supplemental Directives NNSA Policies (NAPs) FAR Federal Acquisition Regulations Federal Acquisition Regulations (FAR) DOE Acquisition Regulations (DEAR) CFR Code of Federal Regulations CFR (annual edition) 10

  10. Archived Reference Building Type: Primary school

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  11. Archived Reference Building Type: Primary school

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  12. Archived Reference Building Type: Outpatient health care

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  13. Archived Reference Building Type: Medium office

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  14. Archived Reference Building Type: Medium office

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  15. Archived Reference Building Type: Small Hotel

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  16. Archived Reference Building Type: Large Hotel

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  17. Archived Reference Building Type: Small Hotel

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  18. Archived Reference Building Type: Secondary school

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  19. Archived Reference Building Type: Secondary school

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  20. Archived Reference Building Type: Outpatient health care

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  1. Archived Reference Building Type: Strip mall

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zonesis available for reference.Current versionsare also available.

  2. Archived Reference Building Type: Strip mall

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  3. Archived Reference Climate Zone: 7 Duluth, Minnesota

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  4. Archived Reference Climate Zone: 7 Duluth, Minnesota

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zones is available for reference. Current versions are also available.

  5. Archived Reference Building Type: Midrise Apartment

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed before 1980, organized by building type and location. A summary ofbuilding types and climate zonesis available for reference.Current versionsare also available.

  6. Archived Reference Building Type: Midrise Apartment

    Energy.gov [DOE]

    Here you will find past versions of the commercial reference building models for existing buildings constructed in or after 1980, organized by building type and location. A summary of building types and climate zones is available for reference. Current versions are also available.

  7. H. R. 4662: a bill to amend the Internal Revenue Code of 1954 to impose a fee on the importation of crude oil and refined petroleum products. Introduced in the House of Representatives, Ninety-Ninth Congress, Second Session, April 22, 1986

    SciTech Connect

    Not Available

    1986-01-01

    A bill to amend the Internal Revenue Code of 1954 to impose a fee on the importation of crude oil and refined petroleum products was introduced and referred to the House Ways and Means Committee. The fee would apply to the first sale of crude or refined petroleum products following importation into the US and the first use. It exempts certain exports, but requires proof of eligibility for exemption. Sections of the bill outline procedures for determining prices and adjustments, the registration of affected parties, and penalties for non-compliance.

  8. Rocky Mountain area petroleum product availability with reduced PADD IV refining capacity

    SciTech Connect

    Hadder, G.R.; Chin, S.M.

    1994-02-01

    Studies of Rocky Mountain area petroleum product availability with reduced refining capacity in Petroleum Administration for Defense IV (PADD IV, part of the Rocky Mountain area) have been performed with the Oak Ridge National Laboratory Refinery Yield Model, a linear program which has been updated to blend gasolines to satisfy constraints on emissions of nitrogen oxides and winter toxic air pollutants. The studies do not predict refinery closures in PADD IV. Rather, the reduced refining capacities provide an analytical framework for probing the flexibility of petroleum refining and distribution for winter demand conditions in the year 2000. Industry analysts have estimated that, for worst case scenarios, 20 to 35 percent of PADD IV refining capacity could be shut-down as a result of clean air and energy tax legislation. Given these industry projections, the study scenarios provide the following conclusions: The Rocky Mountain area petroleum system would have the capability to satisfy winter product demand with PADD IV refinery capacity shut-downs in the middle of the range of industry projections, but not in the high end of the range of projections. PADD IV crude oil production can be maintained by re-routing crude released from PADD IV refinery demands to satisfy increased crude oil demands in PADDs II (Midwest), III (Gulf Coast), and Washington. Clean Air Act product quality regulations generally do not increase the difficulty of satisfying emissions reduction constraints in the scenarios.

  9. Environmental Regulations and Changes in Petroleum Refining Operations (Released in the STEO June 1998)

    Reports and Publications

    1998-01-01

    Changes in domestic refining operations are identified and related to the summer Reid vapor pressure (RVP) restrictions and oxygenate blending requirements. This analysis uses published Energy Information Administration survey data and linear regression equations from the Short-Term Integrated Forecasting System (STIFS). The STIFS model is used for producing forecasts appearing in the Short-Term Energy Outlook.

  10. Table A1. Refiner/Reseller Motor Gasoline Prices by Grade, PAD...

    Energy Information Administration (EIA) (indexed site)

    71.6 92.3 78.2 101.8 83.6 87.5 74.7 See footnotes at end of table. A1. RefinerReseller Motor Gasoline Prices by Grade, PAD District, and State, 1984-Present 452 Energy Information...

  11. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    61.5 67.3 89.8 89.5 82.2 69.4 71.1 74.9 See footnotes at end of table. 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type 12 Energy Information Administration ...

  12. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    35.2 213.6 9.5 9.8 12.9 16.6 NA 29.5 See footnotes at end of table. 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type 14 Energy Information Administration ...

  13. Table 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by...

    Energy Information Administration (EIA) (indexed site)

    W 5.6 0.5 0.5 0.5 0.4 - 0.9 See footnotes at end of table. 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by Grade and Sales Type 22 Energy Information Administration ...

  14. Table 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    62.2 68.5 90.1 89.6 82.4 70.9 NA 75.9 See footnotes at end of table. 6. U.S. Refiner Motor Gasoline Prices by Grade and Sales Type 12 Energy Information Administration ...

  15. Table 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales...

    Energy Information Administration (EIA) (indexed site)

    33.9 215.8 9.7 10.0 12.1 16.3 0.0 28.4 See footnotes at end of table. 7. U.S. Refiner Motor Gasoline Volumes by Grade and Sales Type 14 Energy Information Administration ...

  16. Table 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by...

    Energy Information Administration (EIA) (indexed site)

    - 4.9 0.4 0.4 0.3 0.4 - 0.7 See footnotes at end of table. 11. U.S. Refiner Oxygenated Motor Gasoline Volumes by Grade and Sales Type 22 Energy Information Administration ...

  17. Towards solution and refinement of organic crystal structures by fitting to the atomic pair distribution function

    DOE PAGES [OSTI]

    Prill, Dragica; Juhas, Pavol; Billinge, Simon J. L.; Schmidt, Martin U.

    2016-01-01

    In this study, a method towards the solution and refinement of organic crystal structures by fitting to the atomic pair distribution function (PDF) is developed. Approximate lattice parameters and molecular geometry must be given as input. The molecule is generally treated as a rigid body. The positions and orientations of the molecules inside the unit cell are optimized starting from random values. The PDF is obtained from carefully measured X-ray powder diffraction data. The method resembles `real-space' methods for structure solution from powder data, but works with PDF data instead of the diffraction pattern itself. As such it may bemore » used in situations where the organic compounds are not long-range-ordered, are poorly crystalline, or nanocrystalline. The procedure was applied to solve and refine the crystal structures of quinacridone (β phase), naphthalene and allopurinol. In the case of allopurinol it was even possible to successfully solve and refine the structure in P1 with four independent molecules. As an example of a flexible molecule, the crystal structure of paracetamol was refined using restraints for bond lengths, bond angles and selected torsion angles. In all cases, the resulting structures are in excellent agreement with structures from single-crystal data.« less

  18. EIS-0069: Solvent Refined Coal-II Demonstration Project, Fort Martin, Monongalia County, West Virginia

    Energy.gov [DOE]

    The U.S. Department of Energy developed this statement to assess the potential environmental, economic and social impacts associated with the construction and short-term operation of a 6,000-tons-per-stream-day-capacity facility that will demonstrate the technical operability, economic viability, and environmental acceptability of the solvent refined coal process at Fort Martin, West Virginia.

  19. Towards solution and refinement of organic crystal structures by fitting to the atomic pair distribution function

    SciTech Connect

    Prill, Dragica; Juhas, Pavol; Billinge, Simon J. L.; Schmidt, Martin U.

    2016-01-01

    In this study, a method towards the solution and refinement of organic crystal structures by fitting to the atomic pair distribution function (PDF) is developed. Approximate lattice parameters and molecular geometry must be given as input. The molecule is generally treated as a rigid body. The positions and orientations of the molecules inside the unit cell are optimized starting from random values. The PDF is obtained from carefully measured X-ray powder diffraction data. The method resembles `real-space' methods for structure solution from powder data, but works with PDF data instead of the diffraction pattern itself. As such it may be used in situations where the organic compounds are not long-range-ordered, are poorly crystalline, or nanocrystalline. The procedure was applied to solve and refine the crystal structures of quinacridone (β phase), naphthalene and allopurinol. In the case of allopurinol it was even possible to successfully solve and refine the structure in P1 with four independent molecules. As an example of a flexible molecule, the crystal structure of paracetamol was refined using restraints for bond lengths, bond angles and selected torsion angles. In all cases, the resulting structures are in excellent agreement with structures from single-crystal data.

  20. Exploiting structure similarity in refinement: automated NCS and target-structure restraints in BUSTER

    SciTech Connect

    Smart, Oliver S. Womack, Thomas O.; Flensburg, Claus; Keller, Peter; Paciorek, Włodek; Sharff, Andrew; Vonrhein, Clemens; Bricogne, Gérard

    2012-04-01

    Local structural similarity restraints (LSSR) provide a novel method for exploiting NCS or structural similarity to an external target structure. Two examples are given where BUSTER re-refinement of PDB entries with LSSR produces marked improvements, enabling further structural features to be modelled. Maximum-likelihood X-ray macromolecular structure refinement in BUSTER has been extended with restraints facilitating the exploitation of structural similarity. The similarity can be between two or more chains within the structure being refined, thus favouring NCS, or to a distinct ‘target’ structure that remains fixed during refinement. The local structural similarity restraints (LSSR) approach considers all distances less than 5.5 Å between pairs of atoms in the chain to be restrained. For each, the difference from the distance between the corresponding atoms in the related chain is found. LSSR applies a restraint penalty on each difference. A functional form that reaches a plateau for large differences is used to avoid the restraints distorting parts of the structure that are not similar. Because LSSR are local, there is no need to separate out domains. Some restraint pruning is still necessary, but this has been automated. LSSR have been available to academic users of BUSTER since 2009 with the easy-to-use -autoncs and @@target target.pdb options. The use of LSSR is illustrated in the re-refinement of PDB entries http://scripts.iucr.org/cgi-bin/cr.cgi?rm, where -target enables the correct ligand-binding structure to be found, and http://scripts.iucr.org/cgi-bin/cr.cgi?rm, where -autoncs contributes to the location of an additional copy of the cyclic peptide ligand.

  1. Excepted Service EJ and EK Desk Reference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    1] U.S. DEPARTMENT OF ENERGY Office of the Chief Human Capital Officer 2012 Excepted Service EJ and EK Desk Reference E X E C U T I V E R E S O U R C E S D I V I S I O N [2] Executive Summary The Excepted Service EJ and EK Desk Reference is designed to provide the framework, in conjunction, with the DOE O 329.1 (Excepted Service Authorities for EJ and EK Pay Plans). Specifically, the desk reference addresses the requirements for the Excepted Service EJ and EK positions, to include: * Description

  2. FAQS Reference Guide - Aviation Manager | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    FAQS Reference Guide - Aviation Manager FAQS Reference Guide - Aviation Manager This reference guide addresses the competency statements in the January 2010 edition of...

  3. Microsoft Word - Cross Reference Matrix Introduction.doc | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Cross Reference Matrix Introduction.doc Microsoft Word - Cross Reference Matrix Introduction.doc PDF icon Microsoft Word - Cross Reference Matrix Introduction.doc More Documents & ...

  4. Development of Adaptive Model Refinement (AMoR) for Multiphysics and Multifidelity Problems

    SciTech Connect

    Turinsky, Paul

    2015-02-09

    This project investigated the development and utilization of Adaptive Model Refinement (AMoR) for nuclear systems simulation applications. AMoR refers to utilization of several models of physical phenomena which differ in prediction fidelity. If the highest fidelity model is judged to always provide or exceeded the desired fidelity, than if one can determine the difference in a Quantity of Interest (QoI) between the highest fidelity model and lower fidelity models, one could utilize the fidelity model that would just provide the magnitude of the QoI desired. Assuming lower fidelity models require less computational resources, in this manner computational efficiency can be realized provided the QoI value can be accurately and efficiently evaluated. This work utilized Generalized Perturbation Theory (GPT) to evaluate the QoI, by convoluting the GPT solution with the residual of the highest fidelity model determined using the solution from lower fidelity models. Specifically, a reactor core neutronics problem and thermal-hydraulics problem were studied to develop and utilize AMoR. The highest fidelity neutronics model was based upon the 3D space-time, two-group, nodal diffusion equations as solved in the NESTLE computer code. Added to the NESTLE code was the ability to determine the time-dependent GPT neutron flux. The lower fidelity neutronics model was based upon the point kinetics equations along with utilization of a prolongation operator to determine the 3D space-time, two-group flux. The highest fidelity thermal-hydraulics model was based upon the space-time equations governing fluid flow in a closed channel around a heat generating fuel rod. The Homogenous Equilibrium Mixture (HEM) model was used for the fluid and Finite Difference Method was applied to both the coolant and fuel pin energy conservation equations. The lower fidelity thermal-hydraulic model was based upon the same equations as used for the highest fidelity model but now with coarse spatial

  5. Emergency Responder Radioactive Material Quick Reference Sheet

    Energy.gov [DOE]

    This job aid is a quick reference to assist emergency responders in identifying preliminary safety precautions that should be taken during the initial response phase after arrival at the scene of...

  6. FAQS Reference Guide – General Technical Base

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide has been developed to address the competency statements in the March 2015 reaffirmed edition of DOE Standard (STD)-1146-2007, General Technical Base Qualification Standard.

  7. Excepted Service EJ and EK Desk Reference

    Office of Energy Efficiency and Renewable Energy (EERE)

    The Excepted Service EJ and EK Desk Reference is designed to provide the framework, in conjunction, with the DOE O 329.1 (Excepted Service Authorities for EJ and EK Pay Plans). Specifically, the...

  8. FAQS Reference Guide – Quality Assurance

    Energy.gov [DOE]

    This reference guide has been developed to address the competency statements in the April 2002 edition of DOE-Standard (STD)-1150-2002, Quality Assurance Functional Area Qualification Standard.

  9. New Construction Commercial Reference Buildings — Archive

    Energy.gov [DOE]

    Here you will find past versions of the reference buildings for new construction commercial buildings, organized by building type and location. A summary of building types and climate zones is...

  10. FAQS Reference Guide – Civil/ Structural Engineering

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide has been developed to address the competency statements in the March 2004 edition of DOE-STD-1182-2004, Civil/Structural Engineering Functional Area Qualification Standard.

  11. New Robust References! | OpenEI Community

    OpenEI (Open Energy Information) [EERE & EIA]

    provided document type If I,Robot doesn't exist yet, the template will return a red link specially coded to open in the Reference form so that it can be easily added...

  12. Multi-reference Fourier Transform Holography

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Sthr Research 28 February 2007 Five Images for the Price of One: Using X-ray Holography ... By illuminating several references with coherent x-rays, multiple holographic images of ...

  13. FAQS Reference Guide – Occupational Safety

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide has been developed to address the competency statements in the July 2011 version of DOE-STD-1160-2011, Occupational Safety Functional Area Qualification Standard.

  14. Archive Reference Buildings by Building Type: Warehouse

    Energy.gov [DOE]

    Here you will find past versions of the reference buildings for new construction commercial buildings, organized by building type and location. A summary of building types and climate zones is...

  15. Template:ReferenceHeader | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Reference Library banner, typically across the top of the page, which features a unique color scheme and simple menu. Parameters none Usage It should be called in the following...

  16. FAQS Reference Guide –Radiation Protection

    Office of Energy Efficiency and Renewable Energy (EERE)

    This reference guide has been developed to address the competency statements in the December 2003 edition of DOE-STD-1174-2003, Radiation Protection Functional Area Qualification Standard.

  17. Webinar: Reference Designs for Hydrogen Fueling Stations

    Energy.gov [DOE]

    The Fuel Cell Technologies Office will present a live webinar titled "Reference Designs for Hydrogen Fueling Stations" on Tuesday, October 13, from 12 to 1 p.m. Eastern Daylight Time (EDT).

  18. Magnesium Recycling of Partially Oxidized, Mixed Magnesium-Aluminum Scrap Through Combined Refining and Solid Oxide Membrane (SOM) Electrolysis Processes

    SciTech Connect

    Guan, Xiaofei; Zink, Peter; Pal, Uday

    2012-03-11

    Pure magnesium (Mg) is recycled from 19g of partially oxidized 50.5wt.%Mg-Aluminum (Al) alloy. During the refining process, potentiodynamic scans (PDS) were performed to determine the electrorefining potential for magnesium. The PDS show that the electrorefining potential increases over time as the Mg content inside the Mg-Al scrap decreases. Up to 100% percent of magnesium is refined from the Mg-Al scrap by a novel refining process of dissolving magnesium and its oxide into a flux followed by vapor phase removal of dissolved magnesium and subsequently condensing the magnesium vapors in a separate condenser. The solid oxide membrane (SOM) electrolysis process is employed in the refining system to enable additional recycling of magnesium from magnesium oxide (MgO) in the partially oxidized Mg-Al scrap. The combination of the refining and SOM processes yields 7.4g of pure magnesium; could not collect and weigh all of the magnesium recovered.

  19. Magnesium Recycling of Partially Oxidized, Mixed Magnesium-Aluminum Scrap through Combined Refining and Solid Oxide Membrane Electrolysis Processes

    SciTech Connect

    Xiaofei Guan; Peter A. Zink; Uday B. Pal; Adam C. Powell

    2012-01-01

    Pure magnesium (Mg) is recycled from 19g of partially oxidized 50.5wt.% Mg-Aluminum (Al) alloy. During the refining process, potentiodynamic scans (PDS) were performed to determine the electrorefining potential for magnesium. The PDS show that the electrorefining potential increases over time as the magnesium content inside the Mg-Al scrap decreases. Up to 100% percent of magnesium is refined from the Mg-Al scrap by a novel refining process of dissolving magnesium and its oxide into a flux followed by vapor phase removal of dissolved magnesium and subsequently condensing the magnesium vapor. The solid oxide membrane (SOM) electrolysis process is employed in the refining system to enable additional recycling of magnesium from magnesium oxide (MgO) in the partially oxidized Mg-Al scrap. The combination of the refining and SOM processes yields 7.4g of pure magnesium.

  20. Automotive Stirling reference engine design report

    SciTech Connect

    Not Available

    1981-06-01

    The Reference Stirling Engine System, which was to provide the best possible fuel economy while meeting or exceeding all other program objectives is described. It was designed to meet the requirements of a Reference Vehicle, which is a 1984 GM Pontiac Phoenix (X-body). This design utilizes all new technology that can reasonably be expected to be developed by 1984 and that is judged to provide significant improvement, relative to development risk and cost.

  1. "Analysis of SOFCs using reference electrodes?

    SciTech Connect

    Finklea, Harry; Chen,Xiaoke; Gerdes,Kirk; Pakalapati, Suryanarayana; Celik, Ismail

    2013-07-01

    Reference electrodes are frequently applied to isolate the performance of one electrode in a solid oxide fuel cell. However, reference electrode simulations raise doubt to veracity of data collected using reference electrodes. The simulations predict that the reported performance for the one electrode will frequently contain performance of both electrodes. Nonetheless, recent reports persistently treat data so collected as ideally isolated. This work confirms the predictions of the reference electrode simulations on two SOFC designs, and to provides a method of validating the data measured in the 3-electrode configuration. Validation is based on the assumption that a change in gas composition to one electrode does not affect the impedance of the other electrode at open circuit voltage. This assumption is supported by a full physics simulation of the SOFC. Three configurations of reference electrode and cell design are experimentally examined using various gas flows and two temperatures. Impedance data are subjected to deconvolution analysis and equivalent circuit fitting and approximate polarization resistances of the cathode and anode are determined. The results demonstrate that the utility of reference electrodes is limited and often wholly inappropriate. Reported impedances and single electrode polarization values must be scrutinized on this basis.

  2. References, Canceled-7 Section B- April 16 2010

    Energy.gov [DOE]

    This Section contains S&S references arranged as general references and by topical S&S programmatic areas

  3. Profiling of selenium removal in hydrogen ambient zone-refined tellurium bar using RF-GDOES

    SciTech Connect

    Anil, G. . E-mail: anilpillai_99@yahoo.com; Reddy, M.R.P.; Prasad, D.S.; Ali, S.T.; Munirathnam, N.R.; Prakash, T.L.

    2007-01-15

    Ultrapure tellurium (Te) metal has become an important metal in the strategic sector for fabricating high performance infrared devices for thermal imaging and night vision cameras. Zone refining (ZR) is a proven technique for purification of Te. Selenium (Se), present as an impurity in Te, is not easily removed by ZR under normal conditions as the segregation coefficient (K) is around 0.44-0.50. Hence, ZR was performed in a hydrogen atmosphere, during which Se gets converted to hydrogen selenide at the molten moving zones and carried away into the sodium hydroxide scrubbers. In this study a radio-frequency glow discharge optical emission spectrometer (RF-GDOES) was used for determining the concentration of Se along the 56 cm Te zone-refined bar. It was observed that the initial concentration of 1100 ppb Se was decreased to 30 ppb after 2 cycles.

  4. The effects of air pollution regulations on the US refining industry. Task 3

    SciTech Connect

    Not Available

    1989-06-01

    Numerous air pollution regulations affecting petroleum refineries recently have been promulgated, have been proposed, or are under consideration at the federal, state, and local level. As shown in Figure ES-1, all of these environmental regulations are intended to take effect over the relatively short time period from 1989 through 1995. In the aggregate these regulatory activities have significant implications for the US refining industry and the Nation, including: Major investment requirements; changes in industry profitability; potential closure of some refineries; and potential changes in crude oil or product import dependence. At issue is whether the cumulative effect of these regulations could so adversely affect the US refining industry that US national security would be affected. In addition to the regulations outlined in Figure ES-1, President Bush recently presented a major new plan to improve the nation`s air quality. The aspects of the President`s plan that could strongly affect US refineries are summarized below.

  5. Report to the Congress on the storage of refined petroleum products and on regional supply interruptions

    SciTech Connect

    Not Available

    1991-06-01

    This report describes petroleum and petroleum products storage and supply disruption. Information is presented under the following topics: Historical Perspective; Current Patterns of Supply and Disposition of Petroleum Products in the Primary Distribution System; PADD I Clean Products Supply/Demand; 1990 Regional Petroleum Reserve Annual Computation; Market Infrastructure and Commercial Practices in the California Motor Gasoline Market, as Related to Potential Refined Petroleum Product Reserve Structures and Sales Procedures; Infrastructure and Commercial Practices in the Northeast Distillate Market, as Related to Potential Refined Petroleum Product Reserve Structures and Sales Procedures; Storage Stability Characteristics of Petroleum Products and Crude Oil; Effect of 1990 Clean Air Act Amendments on Demand for Petroleum Product Storage Capacity; and Environmental Regulations on Tanks.

  6. FAQS Reference Guide - Environmental Restoration | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Environmental Restoration FAQS Reference Guide - Environmental Restoration This reference guide addresses the competency statements in the November 2002 edition of DOE-STD-1157-2002, Environmental Restoration Functional Area Qualification Standard. Environmental Restoration Qualification Standard Reference Guide, November 2009 (2.3 MB) More Documents & Publications FAQS Reference Guide - Waste Management FAQS Reference Guide - Criticality Safety (NNSA) FAQS Reference Guide - Transportation

  7. Implications of Increasing Light Tight Oil Production for U.S. Refining -

    Energy Information Administration (EIA) (indexed site)

    Energy Information Administration Implications of Increasing Light Tight Oil Production for U.S. Refining Release date: May 5, 2015 Revised: May 12, 2015 (revision) 1. Background and Analytical Framework Background Recent and projected increases in U.S. crude production have sparked discussion about the implications of current limitations on crude oil exports for prices, including both world and domestic crude oil and petroleum product prices, and for the level of domestic crude production

  8. Grain refinement of cast zinc through magnesium inoculation: Characterisation and mechanism

    SciTech Connect

    Liu, Zhilin; Qiu, Dong; Wang, Feng; Taylor, John A.; Zhang, Mingxing

    2015-08-15

    It was previously found that peritectic-forming solutes are more favourable for the grain refinement of cast Al alloys than eutectic-forming solutes. In this work, we report that the eutectic-forming solute, Mg, can also significantly grain refine cast Zn. Differential thermal analysis (DTA) of a Zn–Mg alloy, in which efficient grain refinement occurred, evidenced an unexpected peak that appeared before the nucleation of η-Zn grains on the DTA spectrum. Based on extensive examination using X-ray diffraction, high resolution SEM and EDS, it was found that: (a) some faceted Zn–Mg intermetallic particles were reproducibly observed; (b) the particles were located at or near grain centres; (c) the atomic ratio of Mg to Zn in the intermetallic compound was determined to be around 1/2. Using tilting selected area diffraction (SAD) and convergent beam Kikuchi line diffraction pattern (CBKLDP) techniques, these faceted particles were identified as MgZn{sub 2} and an orientation relationship between such grain-centred MgZn{sub 2} particles and the η-Zn matrix was determined. Hence, the unexpected peak on the DTA spectrum is believed to correspond to the formation of MgZn{sub 2} particles, which act as effective heterogeneous nucleation sites in the alloy. Together with the effect of Mg solute on restricting grain growth, such heterogeneous nucleation is cooperatively responsible for the grain size reduction in Zn–Mg alloys. - Highlights: • A new eutectic-based grain refiner for the cast Zn was found. • The formation process of an intermetallic compound (MgZn{sub 2}) was characterised. • MgZn{sub 2} can act as potent heterogeneous nucleation sites above the liquidus. • A new OR between MgZn{sub 2} and η-Zn was determined using the CBKLDP technique.

  9. Application of a catalyst deactivation model for hydrotreating solvent refined coal feedstocks

    SciTech Connect

    Nalitham, R.V.

    1983-10-01

    A simple kinetic model, including a first-order catalyst deactivation rate, is applied to upgrading of coal-derived feedstocks prepared from two solvent refined coal fractions. A catalyst deactivation mechanism is proposed which involves the adsorption and surface reaction of coke precursors on catalytic active sites. The effect of feedstock composition, temperature and pressure on kinetic parameters, and in particular the catalyst deactivation rate, is determined.

  10. NREL Refines Method to Convert Lignin to Nylon Precursor - News Releases |

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    NREL NREL Refines Method to Convert Lignin to Nylon Precursor Recent Findings Published in Energy & Environmental Science February 26, 2015 A new study from the Energy Department's National Renewable Energy Laboratory (NREL) demonstrates the conversion of lignin-derived compounds to adipic acid, an important industrial dicarboxylic acid produced for its use as a precursor to nylon, plasticizers, lubricants, polyesters, and other popular products and chemicals. The demonstration is an

  11. Refined BCF-type boundary conditions for mesoscale surface step dynamics

    DOE PAGES [OSTI]

    Zhao, Renjie; Ackerman, David M.; Evans, James W.

    2015-06-24

    Deposition on a vicinal surface with alternating rough and smooth steps is described by a solid-on-solid model with anisotropic interactions. Kinetic Monte Carlo (KMC) simulations of the model reveal step pairing in the absence of any additional step attachment barriers. We explore the description of this behavior within an analytic Burton-Cabrera-Frank (BCF)-type step dynamics treatment. Without attachment barriers, conventional kinetic coefficients for the rough and smooth steps are identical, as are the predicted step velocities for a vicinal surface with equal terrace widths. However, we determine refined kinetic coefficients from a two-dimensional discrete deposition-diffusion equation formalism which accounts for stepmore » structure. These coefficients are generally higher for rough steps than for smooth steps, reflecting a higher propensity for capture of diffusing terrace adatoms due to a higher kink density. Such refined coefficients also depend on the local environment of the step and can even become negative (corresponding to net detachment despite an excess adatom density) for a smooth step in close proximity to a rough step. Incorporation of these refined kinetic coefficients into a BCF-type step dynamics treatment recovers quantitatively the mesoscale step-pairing behavior observed in the KMC simulations.« less

  12. Refined BCF-type boundary conditions for mesoscale surface step dynamics

    SciTech Connect

    Zhao, Renjie; Ackerman, David M.; Evans, James W.

    2015-06-24

    Deposition on a vicinal surface with alternating rough and smooth steps is described by a solid-on-solid model with anisotropic interactions. Kinetic Monte Carlo (KMC) simulations of the model reveal step pairing in the absence of any additional step attachment barriers. We explore the description of this behavior within an analytic Burton-Cabrera-Frank (BCF)-type step dynamics treatment. Without attachment barriers, conventional kinetic coefficients for the rough and smooth steps are identical, as are the predicted step velocities for a vicinal surface with equal terrace widths. However, we determine refined kinetic coefficients from a two-dimensional discrete deposition-diffusion equation formalism which accounts for step structure. These coefficients are generally higher for rough steps than for smooth steps, reflecting a higher propensity for capture of diffusing terrace adatoms due to a higher kink density. Such refined coefficients also depend on the local environment of the step and can even become negative (corresponding to net detachment despite an excess adatom density) for a smooth step in close proximity to a rough step. Incorporation of these refined kinetic coefficients into a BCF-type step dynamics treatment recovers quantitatively the mesoscale step-pairing behavior observed in the KMC simulations.

  13. Source category survey: secondary copper smelting and refining industry. Final report Oct 79-Jan 80

    SciTech Connect

    Snyder, M.K.; Shobe, F.D.

    1980-05-01

    This report presents the results of a survey of the secondary copper smelting and refining industry to determine the probable impact of the development of new source performance standards under Section 111 of the Clean Air Act. The surveyed industry processes copper scrap to produce pure copper or copper alloy, other than brass and bronze. Secondary copper foundries, which melt and cast high-quality copper scrap without refining it, are excluded. Primary copper smelters and refiners, which produce copper from ore, are also excluded, although they also process copper scrap. Process, emissions, and economic data were gathered by literature searches, contacts with representatives of the industry, trade associations, federal government agencies, and state and local air pollution control agencies, and visits to two plants. The industry's production processes, actual and allowable air emissions, and emission control systems are described. State and local emission regulations are compared. Production and capacity are projected to 1989 and the impact of new source performance standards is assessed.

  14. The value of continuity: Refined isogeometric analysis and fast direct solvers

    DOE PAGES [OSTI]

    Garcia, Daniel; Pardo, David; Dalcin, Lisandro; Paszynski, Maciej; Collier, Nathan; Calo, Victor M.

    2016-08-24

    Here, we propose the use of highly continuous finite element spaces interconnected with low continuity hyperplanes to maximize the performance of direct solvers. Starting from a highly continuous Isogeometric Analysis (IGA) discretization, we introduce C0-separators to reduce the interconnection between degrees of freedom in the mesh. By doing so, both the solution time and best approximation errors are simultaneously improved. We call the resulting method “refined Isogeometric Analysis (rIGA)”. To illustrate the impact of the continuity reduction, we analyze the number of Floating Point Operations (FLOPs), computational times, and memory required to solve the linear system obtained by discretizing themore » Laplace problem with structured meshes and uniform polynomial orders. Theoretical estimates demonstrate that an optimal continuity reduction may decrease the total computational time by a factor between p2 and p3, with pp being the polynomial order of the discretization. Numerical results indicate that our proposed refined isogeometric analysis delivers a speed-up factor proportional to p2. In a 2D mesh with four million elements and p=5, the linear system resulting from rIGA is solved 22 times faster than the one from highly continuous IGA. In a 3D mesh with one million elements and p=3, the linear system is solved 15 times faster for the refined than the maximum continuity isogeometric analysis.« less

  15. Development of solid radium-226 reference materials

    SciTech Connect

    Chessmore, R.B.; Engelder, P.R.; Sill, C.W.

    1983-11-01

    Radium-226 reference materials having a matrix similar to soil or tailings samples are not available in sufficient quantity for use by remedial-action contractors to calibrate their laboratory gamma-ray spectrometers. Such reference materials are needed to provide uniform standardization among measurements made by remedial-action contractors. A task, therefore, was undertaken to prepare about 200 pounds each of three different concentrations of radium-226 reference materials by diluting tailings with high-purity silica. Target values for radium-226 content were 50, 15, and 5 pCi/g. The radium-226 content of the reference materials was measured by C.W. Sill of EG and G Idaho, Inc., Idaho Falls, using a high- resolution alpha spectrometry technique standardized with National Bureau of Standards (NBS) standard 4961. A summary of this technique is provided in Appendix A of this report. An independent measurement of the radium-226 content was conducted by Bendix Field Engineering Corporation (Bendix), Grand Junction, Colorado, using a high-resolution Ge(Li) detector, which was calibrated using the New Brunswick Laboratory (NBL) 100-A Series standards. The Ge(Li) detector has also been used to determine the radium-226 content in the calibration models at the Grand Junction facility; these models are used by remedial-action contractors for calibration of borehole logging gamma-ray probes. 8 references, 12 tables.

  16. Evaluation of heavy oil upgrading/refining process designs for HRI Dynacracking and UOP Aurabon Process. Final report

    SciTech Connect

    Davis, H.; Adams, D.G.; Fox, J.V.

    1984-04-01

    The process designs examined consist of two non-commercialized heavy oil upgrading processes; namely, the Hydrocarbon Research, Inc. (HRI) Dynacracking Process and the UOP Process Division (UOP) Aurabon Process. The latter process design includes, besides the Aurabon Process, an integrated hydrotreating section which does have commercial stature. The Dynacracking Process designs cover six cases involving three heavy crude feedstocks. The Aurabon Complex designs are based on four cases, two for each of two heavy crude feedstocks. The engineering support services involved engineering review and assessment of data, drawings, reports and other information generated by the two process designers. Background information, the review and assessment methodology employed for evaluating the process designs, and a detailed discussion of the process design data generated by both process contractors are presented in this report. Significant findings for both processes may be summarized as follows: (1) The process designs were executed using sound engineering principles and practices; (2) Both processes may be deemed to perform in accordance with their process design; (3) a wide variety of heavy oil charge stocks can be upgraded by either process to products generally suitable for further refinery processing; (4) no insurmountable operating or environmental problems are anticipated; (5) the estimated capital investments and operating utility requirements are indicative of the increased cost to process contaminated heavy crudes; (6) the cost differential between the higher quantity lighter crudes and the poorer quality heavy crudes must be sufficient to justify these higher expenditures; and (7) both processes merit consideration by refiners contemplating contaminated heavy oil upgrading. 53 references, 40 tables.

  17. Re-refinement from deposited X-ray data can deliver improved models for most PDB entries

    SciTech Connect

    Joosten, Robbie P.; Womack, Thomas; Vriend, Gert; Bricogne, Gérard

    2009-02-01

    An evaluation of validation and real-space intervention possibilities for improving existing automated (re-)refinement methods. The deposition of X-ray data along with the customary structural models defining PDB entries makes it possible to apply large-scale re-refinement protocols to these entries, thus giving users the benefit of improvements in X-ray methods that have occurred since the structure was deposited. Automated gradient refinement is an effective method to achieve this goal, but real-space intervention is most often required in order to adequately address problems detected by structure-validation software. In order to improve the existing protocol, automated re-refinement was combined with structure validation and difference-density peak analysis to produce a catalogue of problems in PDB entries that are amenable to automatic correction. It is shown that re-refinement can be effective in producing improvements, which are often associated with the systematic use of the TLS parameterization of B factors, even for relatively new and high-resolution PDB entries, while the accompanying manual or semi-manual map analysis and fitting steps show good prospects for eventual automation. It is proposed that the potential for simultaneous improvements in methods and in re-refinement results be further encouraged by broadening the scope of depositions to include refinement metadata and ultimately primary rather than reduced X-ray data.

  18. TriBITS Developers Guide and Reference

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    TriBITS Developers Guide and Reference Ross Bartlett Oak Ridge National Laboratory March 31, 2014 CASL-U-2014-0075-000-E CASL-U-2014-0075-000-b TriBITS Developers Guide and Reference Author: Roscoe A. Bartlett (bartlettra@ornl.gov) Abstract This document describes the usage of TriBITS to build, test, and deploy complex software. The primary audience are those individuals who develop on a software project which uses TriBITS. The overall structure of a TriBITS project is described including all of

  19. Ray Effect Mitigation Through Reference Frame Rotation

    DOE PAGES [OSTI]

    Tencer, John

    2016-05-01

    The discrete ordinates method is a popular and versatile technique for solving the radiative transport equation, a major drawback of which is the presence of ray effects. Mitigation of ray effects can yield significantly more accurate results and enhanced numerical stability for combined mode codes. Moreover, when ray effects are present, the solution is seen to be highly dependent upon the relative orientation of the geometry and the global reference frame. It is an undesirable property. A novel ray effect mitigation technique of averaging the computed solution for various reference frame orientations is proposed.

  20. Positional reference system for ultraprecision machining

    DOEpatents

    Arnold, Jones B.; Burleson, Robert R.; Pardue, Robert M.

    1982-01-01

    A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of position interferometers and part contour description data inputs to calculate error components for each axis of movement and output them to corresponding axis drives with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

  1. Positional reference system for ultraprecision machining

    DOEpatents

    Arnold, J.B.; Burleson, R.R.; Pardue, R.M.

    1980-09-12

    A stable positional reference system for use in improving the cutting tool-to-part contour position in numerical controlled-multiaxis metal turning machines is provided. The reference system employs a plurality of interferometers referenced to orthogonally disposed metering bars which are substantially isolated from machine strain induced position errors for monitoring the part and tool positions relative to the metering bars. A microprocessor-based control system is employed in conjunction with the plurality of positions interferometers and part contour description data input to calculate error components for each axis of movement and output them to corresponding axis driven with appropriate scaling and error compensation. Real-time position control, operating in combination with the reference system, makes possible the positioning of the cutting points of a tool along a part locus with a substantially greater degree of accuracy than has been attained previously in the art by referencing and then monitoring only the tool motion relative to a reference position located on the machine base.

  2. Xyce parallel electronic simulator : reference guide.

    SciTech Connect

    Mei, Ting; Rankin, Eric Lamont; Thornquist, Heidi K.; Santarelli, Keith R.; Fixel, Deborah A.; Coffey, Todd Stirling; Russo, Thomas V.; Schiek, Richard Louis; Warrender, Christina E.; Keiter, Eric Richard; Pawlowski, Roger Patrick

    2011-05-01

    This document is a reference guide to the Xyce Parallel Electronic Simulator, and is a companion document to the Xyce Users Guide. The focus of this document is (to the extent possible) exhaustively list device parameters, solver options, parser options, and other usage details of Xyce. This document is not intended to be a tutorial. Users who are new to circuit simulation are better served by the Xyce Users Guide. The Xyce Parallel Electronic Simulator has been written to support, in a rigorous manner, the simulation needs of the Sandia National Laboratories electrical designers. It is targeted specifically to run on large-scale parallel computing platforms but also runs well on a variety of architectures including single processor workstations. It also aims to support a variety of devices and models specific to Sandia needs. This document is intended to complement the Xyce Users Guide. It contains comprehensive, detailed information about a number of topics pertinent to the usage of Xyce. Included in this document is a netlist reference for the input-file commands and elements supported within Xyce; a command line reference, which describes the available command line arguments for Xyce; and quick-references for users of other circuit codes, such as Orcad's PSpice and Sandia's ChileSPICE.

  3. Steam system opportunity assessment for the pulp and paper, chemical manufacturing, and petroleum refining industries: Main report

    SciTech Connect

    None, None

    2002-10-01

    This report assesses steam generation and use in the pulp and paper, chemical, and petroleum refining industries, and estimates the potential for energy savings from implementation of steam system performance and efficiency improvements.

  4. H. R. 5916: A Bill to require the President of the United States to use the Strategic Petroleum Reserve in the event of a domestic energy supply shortage, to amend the Energy Policy and Conservation Act and the Export Administration Act of 1979 to prohibit the exportation of refined petroleum products except under certain circumstances, and for other purposes, introduced in the House of Representatives, One Hundred First Congress, Second Session, October 24, 1990

    SciTech Connect

    Not Available

    1990-01-01

    The bill amends the Energy Policy and Conservation Act by making mandatory the use of the Strategic Petroleum Reserve in the event of a domestic energy supply shortage. The restriction on the export of refined petroleum products refers to gasoline, kerosene, heating oils, jet fuel, diesel fuel, residual fuel oil, propane, butane, and any natural liquid or natural gas liquid product refined within the US or entered for consumption within the US. The bill also describes the appointment of special investigator to investigate possible gouging and market manipulation by oil companies and the sense of Congress concerning the cost of deployment and maintenance of United States troops in Saudi Arabia.

  5. Evaluation of tropical channel refinement using MPAS-A aquaplanet simulations

    SciTech Connect

    Martini, Matus N.; Gustafson, Jr., William I.; O'Brien, Travis A.; Ma, Po -Lun

    2015-09-13

    Climate models with variable-resolution grids offer a computationally less expensive way to provide more detailed information at regional scales and increased accuracy for processes that cannot be resolved by a coarser grid. This study uses the Model for Prediction Across Scales–Atmosphere (MPAS22A), consisting of a nonhydrostatic dynamical core and a subset of Advanced Research Weather Research and Forecasting (ARW-WRF) model atmospheric physics that have been modified to include the Community Atmosphere Model version 5 (CAM5) cloud fraction parameterization, to investigate the potential benefits of using increased resolution in an tropical channel. The simulations are performed with an idealized aquaplanet configuration using two quasi-uniform grids, with 30 km and 240 km grid spacing, and two variable-resolution grids spanning the same grid spacing range; one with a narrow (20°S–20°N) and one with a wide (30°S–30°N) tropical channel refinement. Results show that increasing resolution in the tropics impacts both the tropical and extratropical circulation. Compared to the quasi-uniform coarse grid, the narrow-channel simulation exhibits stronger updrafts in the Ferrel cell as well as in the middle of the upward branch of the Hadley cell. The wider tropical channel has a closer correspondence to the 30 km quasi-uniform simulation. However, the total atmospheric poleward energy transports are similar in all simulations. The largest differences are in the low-level cloudiness. The refined channel simulations show improved tropical and extratropical precipitation relative to the global 240 km simulation when compared to the global 30 km simulation. All simulations have a single ITCZ. Furthermore, the relatively small differences in mean global and tropical precipitation rates among the simulations are a promising result, and the evidence points to the tropical channel being an effective method for avoiding the extraneous numerical artifacts seen in earlier

  6. Direct Reduction of Waste through Refining of DOE Metal Assets - 13632

    SciTech Connect

    Hargett, Michael C.; Terekhov, Dimitri; Khozan, Kamran M.

    2013-07-01

    CVMR{sup R} presents a technology for refining nickel from the enrichment barrier materials of the DOE that is proven through 100 years of use by the metals industry. CVMR{sup R} applies modern controls, instrumentation for process and monitoring of the system, and innovative production methods to produce a wide spectrum of products that generate new technology applications and improvements to our society and economy. CVMR{sup R} will receive barrier materials as a secure operation and size reduce the metal to a shred that is fed to a carbonylation reactor where nickel is reacted with carbon monoxide and generate nickel carbonyl. The carbonyl will be filtered and decomposed with heat to form a variety of products that include high value nano powders, coated substrates, net shapes and pure nickel. The residue from the reactor will retain radionuclides from enrichment activities. The carbon monoxide will only react and extract nickel under the operating conditions to leave volumetric contamination in the unreacted residue. A demonstration plant was designed and built by CVMR{sup R} and operated by BWXT, to demonstrate the systems capabilities to DOE in 2006. A pilot plant operation precedes the detailed design of the nickel refinery and provides essential data for design, safe work practices, waste characterizations and system kinetics and confirms the project feasibility. CVMR{sup R} produces nickel products that are cleaner than the nickel in U.S. commerce and used by industry today. The CVMR{sup R} process and systems for nickel refining is well suited for DOE materials and will provide value through environmental stewardship, recovery of high value assets, and support of the DOE environmental remediation programs as the refined nickel generates additional long term benefits to local communities. (authors)

  7. Evaluation of Tropical Channel Refinement using MPAS-A Aquaplanet Simulations

    SciTech Connect

    Martini, Matus; Gustafson, William I.; O'Brien, Travis A.; Ma, Po-Lun

    2015-09-13

    Climate models with variable-resolution grids offer a computationally less expensive way to provide more detailed information at regional scales and increased accuracy for processes that cannot be resolved by a coarser grid. This study uses the Model for Prediction Across Scales–Atmosphere (MPAS22A), consisting of a nonhydrostatic dynamical core and a subset of Advanced Research Weather Research and Forecasting (ARW-WRF) model atmospheric physics that have been modified to include the Community Atmosphere Model version 5 (CAM5) cloud fraction parameterization, to investigate the potential benefits of using increased resolution in an tropical channel. The simulations are performed with an idealized aquaplanet configuration using two quasi-uniform grids, with 30 km and 240 km grid spacing, and two variable-resolution grids spanning the same grid spacing range; one with a narrow (20°S–20°N) and one with a wide (30°S–30°N) tropical channel refinement. Results show that increasing resolution in the tropics impacts both the tropical and extratropical circulation. Compared to the quasi-uniform coarse grid, the narrow-channel simulation exhibits stronger updrafts in the Ferrel cell as well as in the middle of the upward branch of the Hadley cell. The wider tropical channel has a closer correspondence to the 30 km quasi-uniform simulation. However, the total atmospheric poleward energy transports are similar in all simulations. The largest differences are in the low-level cloudiness. The refined channel simulations show improved tropical and extratropical precipitation relative to the global 240 km simulation when compared to the global 30 km simulation. All simulations have a single ITCZ. The relatively small differences in mean global and tropical precipitation rates among the simulations are a promising result, and the evidence points to the tropical channel being an effective method for avoiding the extraneous numerical artifacts seen in earlier studies that

  8. Manufacturing Energy and Carbon Footprint - Sector: Petroleum Refining (NAICS 324110), October 2012 (MECS 2006)

    Energy.gov [DOE] (indexed site)

    Petroleum Refining (NAICS 324110) Process Energy Electricity and Steam Generation Losses Process Losses 245 Nonprocess Losses 3,546 641 Steam Distribution Losses 145 20 Nonprocess Energy 2,994 Electricity Generation Steam Generation 3,546 110 Prepared for the Advanced Manufacturing Office (AMO) by Energetics Incorporated 62 2,779 127 Generation and Transmission Losses Generation and Transmission Losses 41 275 Onsite Generation 2,840 2,304 927 3,231 402 151 682 9.6 24.3 33.8 64.7 64.3 144.5 176.0

  9. Methods of refining and producing dibasic esters and acids from natural oil feedstocks

    DOEpatents

    Snead, Thomas E.; Cohen, Steven A.; Gildon, Demond L.

    2016-03-15

    Methods are provided for refining natural oil feedstocks and producing dibasic esters and/or dibasic acids. The methods comprise reacting a terminal olefin with an internal olefin in the presence of a metathesis catalyst to form a dibasic ester and/or dibasic acid. In certain embodiments, the olefin esters are formed by reacting the feedstock in the presence of a metathesis catalyst under conditions sufficient to form a metathesized product comprising olefins and esters, separating the olefins from the esters in the metathesized product, and transesterifying the esters in the presence of an alcohol to form a transesterified product having olefin esters.

  10. MX-2500 thermal processor for the treatment of petroleum refining wastes and contaminated soils

    SciTech Connect

    Swanberg, C. )

    1993-05-01

    Separation and Recovery Systems, Inc. (SRS) of Irvine, California is the market leader in supplying hazardous waste and secondary material dewatering and drying services to the petroleum refining industry. In late 1991, SRS introduced the new generation of dryer technology, the MX-2500. The MX-2500 is an electrically heated dryer system that recovers virtually all of the hydrocarbon value of refinery wastes and secondary materials, while producing a solid residue meeting EPA Land Disposal Restriction (LDR) treatment levels which allows the refinery to land dispose of the solids, thereby realizing two objectives: waste minimization and oil recovery/recycling. 2 figs., 3 tabs.

  11. Managing process innovation through incremental improvements: Empirical evidence in the petroleum refining industry

    SciTech Connect

    Yin, J.Z.

    1994-11-01

    This paper developed a present value index (PVI) model to offer a new solution to differing the effects of radical innovation and incremental improvement. After comparing the return from an initial-radical-process innovation and the return from the incremental changes in petroleum refining processes, it was found that incremental improvements generated higher returns than from its initial innovations. The findings suggest that, in contrast to a conventional research and development (R&D) strategy with a focus on state-of-art innovations, manufacturing companies should place sufficient emphasis on incremental capital and operating improvements to fully exploit economic benefits from an innovation. 49 refs., 3 tabs.

  12. Refinement of overlapping local/global iteration method based on Monte Carlo/p-CMFD calculations

    SciTech Connect

    Jo, Y.; Yun, S.; Cho, N. Z.

    2013-07-01

    In this paper, the overlapping local/global (OLG) iteration method based on Monte Carlo/p-CMFD calculations is refined in two aspects. One is the consistent use of estimators to generate homogenized scattering cross sections. Another is that the incident or exiting angular interval is divided into multi-angular bins to modulate albedo boundary conditions for local problems. Numerical tests show that, compared to the one angle bin case in a previous study, the four angle bin case shows significantly improved results. (authors)

  13. Quantitative phase analysis of Mg:ZrO{sub 2} nanoparticles by Rietveld refinement method

    SciTech Connect

    Balaji, V. Senthilkumaran, S. Thangadurai, P.

    2014-04-24

    To quantify the structural phases of nanocrystalline ZrO{sub 2} doped with Mg ions of varying concentrations (3, 5, 10, 15 and 20%) and annealed at different temperatures. Magnesia doped zirconia was prepared by chemical co-precipitation method and annealed up to 1000°C. The monoclinic and tetragonal phases present in Mg:ZrO{sub 2} were quantified using Rietveld refinement analysis of the X-ray diffraction data and compared with the Direct method based on peak intensity calculations. Tetragonal phase was dominant in the 600°C annealed Mg:ZrO{sub 2} for all Mg concentrations.

  14. Table 3a. Imported Refiner Acquisition Cost of Crude Oil, Projected vs. Actual

    Energy Information Administration (EIA) (indexed site)

    a. Imported Refiner Acquisition Cost of Crude Oil, Projected vs. Actual" "Projected Price in Constant Dollars" " (constant dollars per barrel in ""dollar year"" specific to each AEO)" ,"AEO $ Year",1993,1994,1995,1996,1997,1998,1999,2000,2001,2002,2003,2004,2005,2006,2007,2008,2009,2010,2011,2012,2013 "AEO 1994",1992,16.69,16.42999,16.9899,17.66,18.28,19.0599,19.89,20.72,21.65,22.61,23.51,24.29,24.9,25.6,26.3,27,27.64,28.16

  15. European refiners must seek creative processes to justify heavy-ends projects

    SciTech Connect

    Hunt, P.

    1996-12-09

    There are strong reasons for wanting to upgrade the bottom of the crude oil barrel. But European refiners will not find it easy to get approval and funding for major capital investment projects. In most cases, investment justification will have to be creative and may need to rely on factors traditionally considered to be outside the conventional refinery fence. Examples of such creative upgrading schemes are those employed in four gasification projects planned for refineries in Italy. It is clear that the major obstacles to heavy residue processing are not technical, but economic. A review of these obstacles will set the stage for European investment in bottom-of-the-barrel processing.

  16. Methods of refining and producing dibasic esters and acids from natural oil feedstocks

    SciTech Connect

    Snead, Thomas E; Cohen, Steven A; Gildon, Demond L

    2015-04-07

    Methods are provided for refining natural oil feedstocks and producing dibasic esters and/or dibasic acids. The methods comprise reacting a terminal olefin with an internal olefin in the presence of a metathesis catalyst to form a dibasic ester and/or dibasic acid. In certain embodiments, the olefin esters are formed by reacting the feedstock in the presence of a metathesis catalyst under conditions sufficient to form a metathesized product comprising olefins and esters, separating the olefins from the esters in the metathesized product, and transesterifying the esters in the presence of an alcohol to form a transesterified product having olefin esters.

  17. ,"U.S. Refiner Acquisition Cost of Crude Oil"

    Energy Information Administration (EIA) (indexed site)

    Acquisition Cost of Crude Oil" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","U.S. Refiner Acquisition Cost of Crude Oil",3,"Monthly","9/2016","1/15/1974" ,"Release Date:","11/1/2016" ,"Next Release Date:","12/1/2016" ,"Excel File

  18. Reference electrode for strong oxidizing acid solutions

    DOEpatents

    Rigdon, Lester P.; Harrar, Jackson E.; Bullock, Sr., Jack C.; McGuire, Raymond R.

    1990-01-01

    A reference electrode for the measurement of the oxidation-reduction potentials of solutions is especially suitable for oxidizing solutions such as highly concentrated and fuming nitric acids, the solutions of nitrogen oxides, N.sub.2 O.sub.4 and N.sub.2 O.sub.5, in nitric acids. The reference electrode is fabricated of entirely inert materials, has a half cell of Pt/Ce(IV)/Ce(III)/70 wt. % HNO.sub.3, and includes a double-junction design with an intermediate solution of 70 wt. % HNO.sub.3. The liquid junctions are made from Corning No. 7930 glass for low resistance and negligible solution leakage.

  19. Category:Smart Grid References | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Category Edit History Category:Smart Grid References Jump to: navigation, search Add a new Reference Pages in category "Smart Grid References" The following 11 pages are in this...

  20. Molecular dynamics force-field refinement against quasi-elastic neutron scattering data

    DOE PAGES [OSTI]

    Borreguero Calvo, Jose M.; Lynch, Vickie E.

    2015-11-23

    Quasi-elastic neutron scattering (QENS) is one of the experimental techniques of choice for probing the dynamics at length and time scales that are also in the realm of full-atom molecular dynamics (MD) simulations. This overlap enables extension of current fitting methods that use time-independent equilibrium measurements to new methods fitting against dynamics data. We present an algorithm that fits simulation-derived incoherent dynamical structure factors against QENS data probing the diffusive dynamics of the system. We showcase the difficulties inherent to this type of fitting problem, namely, the disparity between simulation and experiment environment, as well as limitations in the simulationmore » due to incomplete sampling of phase space. We discuss a methodology to overcome these difficulties and apply it to a set of full-atom MD simulations for the purpose of refining the force-field parameter governing the activation energy of methyl rotation in the octa-methyl polyhedral oligomeric silsesquioxane molecule. Our optimal simulated activation energy agrees with the experimentally derived value up to a 5% difference, well within experimental error. We believe the method will find applicability to other types of diffusive motions and other representation of the systems such as coarse-grain models where empirical fitting is essential. In addition, the refinement method can be extended to the coherent dynamic structure factor with no additional effort.« less