National Library of Energy BETA

Sample records for boundary print earth

  1. Compressional boundaries in the Earth's foreshock

    SciTech Connect

    Rojas-Castillo, D.; Blanco-Cano, X.; Kajdic, P.; Omidi, N.

    2013-06-13

    The terrestrial foreshock is a highly dynamic region populated by particles, waves and non-linear structures such as shocklets, SLAMS, hot flow anomalies, cavities and cavitons. Recently a new structure named foreshock compressional boundary (FCB) was reported in global hybrid simulations by Omidi et al. (2009). This structure represents a transition region that separates the highly disturbed foreshock plasma from pristine solar wind or from the region of field-aligned ion beams. The FCB is associated with a strong compression of magnetic field and density. Besides the enhancements in the field and density, the FCB also shows a region where these two quantities decrease below the ambient solar wind (SW) values. Here, we study a FCB observed by Cluster-1. This FCB shows that although sometimes FCBs are transition regions between the pristine solar wind plasma and the foreshock plasma, in this case the FCB separates a region with large amplitude waves from regions with high frequency (f{approx}1.7 Hz) small amplitude waves. We analyze the FCB properties, ion distributions inside them, and the waves near the structure.

  2. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    parallel to the boundary, which is just what seismologists observe. These results open new possibilities for modeling anisotropy evolution at extreme conditions, linking...

  3. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    core-mantle boundary (CMB), 2900 km deep, seismologists have discovered that seismic waves travel faster in certain directions. This seismic anisotropy appears to be related to...

  4. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    (except for its liquid-iron outer core), this convection causes deformation of solid rocks by plastic flow. At the core-mantle boundary (CMB), 2900 km deep, seismologists have...

  5. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    is a dynamic planet in which convection takes place on the scale of thousands of kilometers. Because Earth is mostly solid (except for its liquid-iron outer core), this...

  6. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    the ultrahigh pressures of the deep Earth at ALS Beamline 12.2.2 while conducting in situ x-ray diffraction experiments to probe changes in crystal orientations. Rocks Flow in the...

  7. Earth

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth Earth Climate impacts, including global temperatures, drought and forest fires as well as ocean and sea ice modeling. News Releases Science Briefs Photos Picture of the Week Publications Social Media Videos Fact Sheets James TenCate James TenCate elected Acoustical Society of America fellow TenCate's research focuses on nonlinear acoustics and elasticity, seismology and nonlinear imaging. - 8/30/16 The thermal traits of a leaf, critical for photosynthesis, may be under strong evolutionary

  8. Shape of the terrestrial plasma sheet in the near-Earth magnetospheric tail as imaged by the Interstellar Boundary Explorer

    DOE PAGES [OSTI]

    Dayeh, M. A.; Fuselier, S. A.; Funsten, H. O.; McComas, D. J.; Ogasawara, K.; Petrinec, S. M.; Schwadron, N. A.; Valek, P.

    2015-04-11

    We present remote, continuous observations from the Interstellar Boundary Explorer of the terrestrial plasma sheet location back to -16 Earth radii (RE) in the magnetospheric tail using energetic neutral atom emissions. The time period studied includes two orbits near the winter and summer solstices, thus associated with large negative and positive dipole tilt, respectively. Continuous side-view images reveal a complex shape that is dominated mainly by large-scale warping due to the diurnal motion of the dipole axis. Superposed on the global warped geometry are short-time fluctuations in plasma sheet location that appear to be consistent with plasma sheet flapping andmore » possibly twisting due to changes in the interplanetary conditions. We conclude that the plasma sheet warping due to the diurnal motion dominates the average shape of the plasma sheet. Over short times, the position of the plasma sheet can be dominated by twisting and flapping.« less

  9. Shape of the terrestrial plasma sheet in the near-Earth magnetospheric tail as imaged by the Interstellar Boundary Explorer

    SciTech Connect

    Dayeh, M. A.; Fuselier, S. A.; Funsten, H. O.; McComas, D. J.; Ogasawara, K.; Petrinec, S. M.; Schwadron, N. A.; Valek, P.

    2015-04-11

    We present remote, continuous observations from the Interstellar Boundary Explorer of the terrestrial plasma sheet location back to -16 Earth radii (RE) in the magnetospheric tail using energetic neutral atom emissions. The time period studied includes two orbits near the winter and summer solstices, thus associated with large negative and positive dipole tilt, respectively. Continuous side-view images reveal a complex shape that is dominated mainly by large-scale warping due to the diurnal motion of the dipole axis. Superposed on the global warped geometry are short-time fluctuations in plasma sheet location that appear to be consistent with plasma sheet flapping and possibly twisting due to changes in the interplanetary conditions. We conclude that the plasma sheet warping due to the diurnal motion dominates the average shape of the plasma sheet. Over short times, the position of the plasma sheet can be dominated by twisting and flapping.

  10. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    29 Oct 2015 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Tech Specs for Boundary and first...

  11. Printing | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Printing Printing The Printing Team is the liaison between the U.S. Government Printing Office and the Department of Energy. It consists of an expert group of printing specialists who offer a full range of services from assistance in developing your printing requirements to the final printing, distribution and mailing of products. The printed products range from black and white to full color items. These Services are available through the Working Capital Fund or CID (Direct Charge

  12. World's First Printed Car

    SciTech Connect

    Rogers, Jay

    2015-06-03

    Local Motors partnered with ORNL to print the world’s first 3D-printed car (Strati) at the 2014 International Manufacturing Technology Show.

  13. Evidence for a Weak Iron Core at Earth's Center

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Iron Core at Earth's Center Print Seismic waves that pass through the center of the Earth travel faster going from pole to pole than along the equatorial plane-why? One theory...

  14. The Iron Spin Transition in the Earth's Lower Mantle

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    The Iron Spin Transition in the Earth's Lower Mantle Print It is now known that the iron present in minerals of the lower mantle of the Earth undergoes a pressure-induced...

  15. The Iron Spin Transition in the Earth's Lower Mantle

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    The Iron Spin Transition in the Earth's Lower Mantle The Iron Spin Transition in the Earth's Lower Mantle Print Wednesday, 30 April 2008 00:00 It is now known that the iron present...

  16. Evidence for a Weak Iron Core at Earth's Center

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Evidence for a Weak Iron Core at Earth's Center Print Seismic waves that pass through the center of the Earth travel faster going from pole to pole than along the equatorial...

  17. Compact organic vapor jet printing print head

    DOEpatents

    Forrest, Stephen R; McGraw, Gregory

    2013-12-24

    A first device is provided. The first device includes a print head, and a first gas source hermetically sealed to the print head. The print header further includes a first layer comprising a plurality of apertures, each aperture having a smallest dimension of 0.5 to 500 microns. A second layer is bonded to the first layer. The second layer includes a first via in fluid communication with the first gas source and at least one of the apertures. The second layer is made of an insulating material.

  18. Compact organic vapor jet printing print head

    DOEpatents

    Forrest, Stepehen R; McGraw, Gregory

    2015-01-27

    A first device is provided. The first device includes a print head, and a first gas source hermetically sealed to the print head. The print head further includes a first layer further comprising a plurality of apertures, each aperture having a smallest dimension of 0.5 to 500 microns. A second layer is bonded to the first layer. The second layer includes a first via in fluid communication with the first gas source and at least one of the apertures. The second layer is made of an insulating material.

  19. Boundary Layer Structure:

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Boundary Layer Structure: a comparison between methods and sites Thiago Biscaro Suzane de Sá Jae-In Song Shaoyue "Emily" Qiu Mentors: Virendra Ghate and Ewan O'Connor July 24 2015 1 st ever ARM Summer Training Outline * IntroducQon * Methodology * Results - SGP - MAO - Comparison between the 2 sites * Conclusions INTRODUCTION Focus: esQmates of PBL height Boundary Layer: "The boUom layer of the troposphere that is in contact with the surface of the earth." (AMS, Glossary of

  20. Underground helium travels to the Earth's surface via aquifers...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Tweet EmailPrint Before it can put the party in party balloons, helium is carried from deep within the Earth's crust to the surface via aquifers, according to new research...

  1. Evidence for a Weak Iron Core at Earth's Center

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Evidence for a Weak Iron Core at Earth's Center Print Seismic waves that pass through the ... be aligned in a way that transmits waves more efficiently in one direction than the other. ...

  2. Organic vapor jet printing system

    DOEpatents

    Forrest, Stephen R.

    2016-05-03

    An organic vapor jet printing system includes a pump for increasing the pressure of an organic flux.

  3. Organic vapor jet printing system

    DOEpatents

    Forrest, Stephen R

    2012-10-23

    An organic vapor jet printing system includes a pump for increasing the pressure of an organic flux.

  4. Government Printing Office Requirements | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Government Printing Office Requirements Government Printing Office Requirements This section describes the Government Printing Office (GPO) requirements for all print materials, whether printed electronically or on paper. This includes requirements for printing and copying for all EERE publications. Approved Printers Executive Order 12873, signed by President Clinton, requires that all government offices and their contractors are required to use GPO-approved printers to print and copy all

  5. rare earth magnets | Critical Materials Institute

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    magnets mlthach's picture Magnetic moments: 3D printers promise better, cheaper and more powerful magnets Submitted by mlthach on Thu, 11/17/2016 - 12:35 Article on two recent papers about 3D printing of magnets -- one is CMI-funded research based at Oak Ridge National Laboratory Tags: rare earth magnets Read more about Magnetic moments: 3D printers promise better, cheaper and more powerful magnets Subscribe to RSS - rare earth magnets

  6. Sintering Kinetics of Inkjet Printed...

    Office of Scientific and Technical Information (OSTI)

    circuits for functional applications envisioned by automotive and aerospace industries. ... Figure 1 illustrates the types of printed line instabilities generally encountered when ...

  7. Template:PrintPDFButton | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    PrintPDFButton Jump to: navigation, search This is the PrintPDFButton template. It is intended for inclusion on any page where printing the page contents to a PDF is desirable....

  8. Widget:PrintPDFButton | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Dependencies Template:PrintPDFButton Usage This Widget assumes the existence of HTML elements created by the PrintPDFButton template, and is called via that template....

  9. Pennsylvania Company Develops Solar Cell Printing Technology

    Energy.gov [DOE]

    The technology uses Plextronics’ conductive inks that can be printed by manufacturers worldwide to make solar cells, potentially as easily as they might print a newspaper.

  10. SolarPrint | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    search Name: SolarPrint Place: Dublin, Ireland Sector: Solar Product: Irish solar cell manufacturer. The company developed DSSC technology. References: SolarPrint1 This...

  11. SciTech Connect: "3d printing"

    Office of Scientific and Technical Information (OSTI)

    3d printing" Find + Advanced Search Term Search Semantic Search Advanced Search All Fields: "3d printing" Semantic Semantic Term Title: Full Text: Bibliographic Data: Creator ...

  12. printed-circuit heat exchanger PCHE

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    printed-circuit heat exchanger PCHE - Sandia Energy Energy Search Icon Sandia Home ... SunShot Grand Challenge: Regional Test Centers printed-circuit heat exchanger PCHE Home...

  13. Public Law 102-392 for Printing | Department of Energy

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    2-392 for Printing Public Law 102-392 for Printing Public Law 102-392 for Printing Public Law 102-392 for Printing (118.61 KB) More Documents & Publications Minutes from the Print ...

  14. Printed Module Interconnects

    SciTech Connect

    Stockert, Talysa R.; Fields, Jeremy D.; Pach, Gregory F.; Mauger, Scott A.; van Hest, Maikel F. A. M.

    2015-06-14

    Monolithic interconnects in photovoltaic modules connect adjacent cells in series, and are typically formed sequentially involving multiple deposition and scribing steps. Interconnect widths of 500 um every 10 mm result in 5% dead area, which does not contribute to power generation in an interconnected solar panel. This work expands on previous work that introduced an alternative interconnection method capable of producing interconnect widths less than 100 um. The interconnect is added to the module in a single step after deposition of the photovoltaic stack, eliminating the need for scribe alignment. This alternative method can be used for all types of thin film photovoltaic modules. Voltage addition with copper-indium-gallium-diselenide (CIGS) solar cells using a 2-scribe printed interconnect approach is demonstrated. Additionally, interconnect widths of 250 um are shown.

  15. Detection of latent prints by Raman imaging

    DOEpatents

    Lewis, Linda Anne; Connatser, Raynella Magdalene; Lewis, Sr., Samuel Arthur

    2011-01-11

    The present invention relates to a method for detecting a print on a surface, the method comprising: (a) contacting the print with a Raman surface-enhancing agent to produce a Raman-enhanced print; and (b) detecting the Raman-enhanced print using a Raman spectroscopic method. The invention is particularly directed to the imaging of latent fingerprints.

  16. Earth's Magnetosphere

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Mysterious electron stash found hidden among Van Allen belts March 1, 2013 Instruments detect never-before-seen phenomenon in Earth's Magnetosphere LOS ALAMOS, N.M., March 1, 2013-U.S. researchers, including a trio from Los Alamos National Laboratory, have witnessed the mysterious appearance of a relatively long-lived zone of high-energy electrons stored between Earth's Van Allen radiation belts. The surprising findings, discovered by NASA's Van Allen Probes (formerly known as the Radiation Belt

  17. Earth materials and earth dynamics

    SciTech Connect

    Bennett, K; Shankland, T.

    2000-11-01

    In the project ''Earth Materials and Earth Dynamics'' we linked fundamental and exploratory, experimental, theoretical, and computational research programs to shed light on the current and past states of the dynamic Earth. Our objective was to combine different geological, geochemical, geophysical, and materials science analyses with numerical techniques to illuminate active processes in the Earth. These processes include fluid-rock interactions that form and modify the lithosphere, non-linear wave attenuations in rocks that drive plate tectonics and perturb the earth's surface, dynamic recrystallization of olivine that deforms the upper mantle, development of texture in high-pressure olivine polymorphs that create anisotropic velocity regions in the convecting upper mantle and transition zone, and the intense chemical reactions between the mantle and core. We measured physical properties such as texture and nonlinear elasticity, equation of states at simultaneous pressures and temperatures, magnetic spins and bonding, chemical permeability, and thermal-chemical feedback to better characterize earth materials. We artificially generated seismic waves, numerically modeled fluid flow and transport in rock systems and modified polycrystal plasticity theory to interpret measured physical properties and integrate them into our understanding of the Earth. This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL).

  18. Add your e-prints to the E-print Network -- Energy, science,...

    Office of Scientific and Technical Information (OSTI)

    Add E-prints: eprintshelp@osti.gov We invite you to submit your e-prints to the network. Having your e-prints in the network increases awareness of them and promotes the ...

  19. Minutes from the Print and Mail Managers Exchange Forum Teleconference...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Minutes from the Print and Mail Managers Exchange Forum Teleconferences Minutes from the Print and Mail Managers Exchange Forum Teleconferences Minutes from the Print and Mail...

  20. The United States Code - Printing, Title 44 Excerpts | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    The United States Code - Printing, Title 44 Excerpts The United States Code - Printing, Title 44 Excerpts The United States Code - Printing, Title 44 Excerpts PDF icon The United ...

  1. High resolution printing of charge

    DOEpatents

    Rogers, John; Park, Jang-Ung

    2015-06-16

    Provided are methods of printing a pattern of charge on a substrate surface, such as by electrohydrodynamic (e-jet) printing. The methods relate to providing a nozzle containing a printable fluid, providing a substrate having a substrate surface and generating from the nozzle an ejected printable fluid containing net charge. The ejected printable fluid containing net charge is directed to the substrate surface, wherein the net charge does not substantially degrade and the net charge retained on the substrate surface. Also provided are functional devices made by any of the disclosed methods.

  2. Scientists compose complex math equations to replicate behaviors of Earth

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    systems | Argonne National Laboratory Rob Jacob talks about climate models Climate Models: Rob Jacob Scientists compose complex math equations to replicate behaviors of Earth systems By Angela Hardin * December 16, 2015 Tweet EmailPrint Whenever news breaks about what Earth's climate is expected to be like decades into the future or how much rainfall various regions around the country or the world are likely to receive, those educated estimates are generated by a global climate model. But

  3. Google Earth Tour: Contaminants

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Google Earth Tour: Contaminants Google Earth Tour: Contaminants Historical operations used the best available waste handling methods for that time.

  4. Heat sinking for printed circuitry

    DOEpatents

    Wilson, S.K.; Richardson, G.; Pinkerton, A.L.

    1984-09-11

    A flat pak or other solid-state device mounted on a printed circuit board directly over a hole extends therethrough so that the bottom of the pak or device extends beyond the bottom of the circuit board. A heat sink disposed beneath the circuit board contacts the bottom of the pak or device and provides direct heat sinking thereto. Pressure may be applied to the top of the pak or device to assure good mechanical and thermal contact with the heat sink.

  5. Processing a printed wiring board by single bath electrodeposition

    DOEpatents

    Meltzer, Michael P.; Steffani, Christopher P.; Gonfiotti, Ray A.

    2010-12-07

    A method of processing a printed wiring board. Initial processing steps are implemented on the printed wiring board. Copper is plated on the printed wiring board from a bath containing nickel and copper. Nickel is plated on the printed wiring board from a bath containing nickel and copper and final processing steps are implemented on the printed wiring board.

  6. Processing A Printed Wiring Board By Single Bath Electrodeposition

    DOEpatents

    Meltzer, Michael P. (Oakland, CA); Steffani, Christopher P. (Livermore, CA); Gonfiotti, Ray A. (Livermore, CA)

    2003-04-15

    A method of processing a printed wiring board by single bath electrodeposition. Initial processing steps are implemented on the printed wiring board. Copper is plated on the printed wiring board from a bath containing nickel and copper. Nickel is plated on the printed wiring board from the bath containing nickel and copper and final processing steps are implemented on the printed wiring board.

  7. Toppan Printing Co Ltd | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Co Ltd Jump to: navigation, search Name: Toppan Printing Co Ltd Place: Tokyo, Tokyo, Japan Zip: 101-0024 Product: Japanese manufacturer of PV module backsheets. Coordinates:...

  8. Mac OS X Printing with LPD

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Mac OS X Printing with LPD Last Modified by Jerry Camuso, 02/12/2015. 1 . From the "System Preferences", click on "Print & Fax" 2 . Click on "+" sign to add a new printer 3. Use "IP Printer" and select or type the following: Protocol: Line Printer Daemon - LPD Address: printserv.slac.stanford.edu Queue: Your print queue name from SLAC printserv. PLEASE NOTE: this information can be found at the bottom of this document Under "SSRL beamline print

  9. Printing and Mail Managers Exchange Forum Teleconference

    Office of Environmental Management (EM)

    ... Streamlining the acquisition process; e. Developing best practices in print management; f. Assisting in behavioral changes through improved data collection and analysis; g. Driving ...

  10. Printed circuit dispersive transmission line

    DOEpatents

    Ikezi, H.; Lin-Liu, Y.R.; DeGrassie, J.S.

    1991-08-27

    A printed circuit dispersive transmission line structure is disclosed comprising an insulator, a ground plane formed on one surface of the insulator, a first transmission line formed on a second surface of the insulator, and a second transmission line also formed on the second surface of the insulator and of longer length than the first transmission line and periodically intersecting the first transmission line. In a preferred embodiment, the transmission line structure exhibits highly dispersive characteristics by designing the length of one of the transmission line between two adjacent periodic intersections to be longer than the other. 5 figures.

  11. Printed circuit dispersive transmission line

    DOEpatents

    Ikezi, Hiroyuki; Lin-Liu, Yuh-Ren; DeGrassie, John S.

    1991-01-01

    A printed circuit dispersive transmission line structure is disclosed comprising an insulator, a ground plane formed on one surface of the insulator, a first transmission line formed on a second surface of the insulator, and a second transmission line also formed on the second surface of the insulator and of longer length than the first transmission line and periodically intersecting the first transmission line. In a preferred embodiment, the transmission line structure exhibits highly dispersive characteristics by designing the length of one of the transmission line between two adjacent periodic intersections to be longer than the other.

  12. Print

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    maneras fciles de usar energa en forma inteligente Apaga las luces. Marca la caja. Apaga tu computadora. Usa bombillas de alta eficiencia energtica. Desenchufa los cargadores...

  13. Print

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Apaga las luces. Marca la caja. Apaga tu computadora. Usa bombillas de alta eficiencia energtica. Desenchufa los cargadores cuando no estn en uso. Usa luz natural, calor del ...

  14. Print

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    GFDL GCM Model Output with ARM CMBE Dataset: A First Look Jean-Christophe Golaz, UCAR VSP, GFDL Leo J. Donner and V. Ramaswamy, Geophysical Fluid Dynamics Laboratory, Princeton, NJ U . S . D E P A R T M E NT O F C O M M E R C E N A TION A L O C E A N I C A N D A T MO S P H E R I C A D M I N I S T R ATIO N What is CMBE? - CMBE (Climate Modeling Best Estimate) is a new ARM dataset specifically designed to evaluate climate models against ARM observations. - CMBE contains best estimates of selected

  15. Print

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    5k 0 < 50k < 100k < 250k < 500k < 1M > 1M > 5M > 10M DE MD DC MA RI NJ AZ UT WY ID OR WA CA TX OK KS CO NE SD ND MN WI IL IA MO AR LA MS AL FL GA TN KY IN OH MI ME NH CT VT NY PA WV VA NC SC MT AK HI NV NM Princeton Plasma Physics Laboratory Procured Materials and Services 2015 (> $35M) Small business procurements in US: $14.73M

  16. Printing a Car: A Team Effort in Innovation (Text Version) |...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Printing a Car: A Team Effort in Innovation (Text Version) Printing a Car: A Team Effort in Innovation (Text Version) Below is the text version of the video Printing a Car: A Team ...

  17. E-print Network : Main View : Deep Federated Search

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    javascript. Home About Contact Us Help E-print Network Search Powered By Deep Web Technologies New Search Preferences E-print Network E-print Network Skip to main content FAQ *...

  18. Template:PrintFullVersionButton | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    PrintFullVersionButton Jump to: navigation, search This is the PrintFullVersionButton template. It is intended for inclusion on any page where the printing of a superset of pages...

  19. Over 5 million scientific e-prints at E-print network | OSTI, US Dept of

    Office of Scientific and Technical Information (OSTI)

    Energy Office of Scientific and Technical Information 5 million scientific e-prints at E-print network Back to the OSTI News Listing for 2008 Now you can access more than 5 million e-prints at OSTI's E-print Network. The rapidly growing gateway to over 27,850 scientific Web sites and databases worldwide allows free one-stop searching of scientific and technical information created by scientists and research engineers active in their respective fields. E-prints are available in basic and

  20. Search 1.1 million scientific e-prints at OSTI's E-print Network | OSTI,

    Office of Scientific and Technical Information (OSTI)

    US Dept of Energy Office of Scientific and Technical Information 1.1 million scientific e-prints at OSTI's E-print Network Back to the OSTI News Listing for 2007 The network created by scientists for scientists continues to grow. E-print Network provides electronic access to more than 27,000 Web sites and databases worldwide containing 1.1 million e-prints in basic and applied sciences. E-prints are scientific or technical documents circulated electronically to facilitate peer exchange and

  1. Minutes from the March 17, 2010 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    March 17, 2010 Printing and Mail Managers Exchange Forum Teleconference Twenty-eight individuals participated in the Printing and Mail Managers Exchange Forum, which included Printing and Mail Managers and Contractors. Comments/Additions to last Months Minutes Dallas Woodruff, Headquarters opened the meeting by thanking everyone for participating in the today's teleconference. Printing Agenda Items... Upcoming Congressional Joint Committee on Printing Commercial Printing Report "JCP Form

  2. Minutes from the May 26, 2010 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    26, 2010 Printing and Mail Managers Exchange Forum Teleconference Seventeen individuals participated in the Printing and Mail Managers Exchange Forum, which included Printing and Mail Managers and Contractors. Comments/Additions to last Months Minutes Dallas Woodruff, Headquarters opened the meeting by thanking everyone for participating in the today's teleconference. Printing Agenda Items... Update on the FY 2010, Congressional Joint Committee on Printing Commercial Printing Report "JCP

  3. Google Earth Tour: Contaminants

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Google Earth Tour: Contaminants Google Earth Tour: Contaminants Historical operations used the best available waste handling methods for that time. Open full screen to view more...

  4. Computational Earth Science

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    6 Computational Earth Science We develop and apply a range of high-performance computational methods and software tools to Earth science projects in support of environmental ...

  5. Earth and Environmental Sciences

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    EES Earth and Environmental Sciences (EES) Sustainable energy, climate impacts, nuclear threat detection, and environmental management are primary focus areas of earth and...

  6. Print-based Manufacturing of Integrated, Low Cost, High Performance...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Print-based Manufacturing of Integrated, Low Cost, High Performance SSL Luminaires Print-based Manufacturing of Integrated, Low Cost, High Performance SSL Luminaires Lead ...

  7. Department of Energy Strategic Plan, May 2011, Print Quality...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Strategic Plan, May 2011, Print Quality Department of Energy Strategic Plan, May 2011, Print Quality Posted here are publication materials related to the ...

  8. Transfer Printed Microcells with Micro-Optic Concentrators for...

    Office of Scientific and Technical Information (OSTI)

    Transfer Printed Microcells with Micro-Optic Concentrators for Low Cost, High Performance Photovoltaic Modules Citation Details In-Document Search Title: Transfer Printed...

  9. Unitech Printed Circuit Board Corp UPCB | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Sector: Solar Product: Taiwan-based printed-circuit board maker with intent to enter into solar cell manufacturing industry. References: Unitech Printed Circuit Board Corp....

  10. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    diffraction images were collected to document the evolution of pressure, differential stress, and texture. Inverse pole figures (IPFs) show the probability of finding the pole...

  11. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    consists mostly of oxygen, silicon, and magnesium, often in the form of magnesium silicate (MgSiO3). In the lower mantle, this magnesium silicate has a crystal structure known...

  12. Mineral Deformation at Earth's Core-Mantle Boundary

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    seismologists have discovered that seismic waves travel faster in certain directions. ... exhibits a seismic discontinuity: shear waves (S-waves) increase in velocity a few ...

  13. Earth coupled cooling techniques

    SciTech Connect

    Grondzik, W.T.; Boyer, L.L.; Johnston, T.L.

    1981-01-01

    Earth coupled cooling is an important consideration for residential and commercial designers, owners, and builders in many regions of the country. The potential benefits which can be expected from passive earth contact cooling are reviewed. Recommendations for the design of earth sheltered structures incorporating earth coupled cooling strategies are also presented.

  14. CoolEarth formerly Cool Earth Solar | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    CoolEarth formerly Cool Earth Solar Jump to: navigation, search Name: CoolEarth (formerly Cool Earth Solar) Place: Livermore, California Zip: 94550 Product: CoolEarth is a...

  15. Earth, Space Sciences

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth, Space Sciences Earth, Space Sciences National security depends on science and technology. The United States relies on Los Alamos National Laboratory for the best of both. No place on Earth pursues a broader array of world-class scientific endeavors. Climate, Ocean and Sea Ice Modeling (COSIM)» Earth and Environmental Sciences Division» Intelligence and Space Research» Earth Read caption + A team of scientists is working to understand how local changes in hydrology might bring about

  16. How We 3D-Print Aerogel

    SciTech Connect

    2015-04-23

    A new type of graphene aerogel will make for better energy storage, sensors, nanoelectronics, catalysis and separations. Lawrence Livermore National Laboratory researchers have made graphene aerogel microlattices with an engineered architecture via a 3D printing technique known as direct ink writing. The research appears in the April 22 edition of the journal, Nature Communications. The 3D printed graphene aerogels have high surface area, excellent electrical conductivity, are lightweight, have mechanical stiffness and exhibit supercompressibility (up to 90 percent compressive strain). In addition, the 3D printed graphene aerogel microlattices show an order of magnitude improvement over bulk graphene materials and much better mass transport.

  17. Aluminum plasmonic metamaterials for structural color printing

    DOE PAGES [OSTI]

    Cheng, Fei; Gao, Jie; Stan, Liliana; Rosenmann, Daniel; Czaplewski, David; Yang, Xiaodong

    2015-05-26

    We report a structural color printing platform based on aluminum plasmonic metamaterials supporting near perfect light absorption and narrow-band spectral response tunable across the visible spectrum to realize high-resolution, angle-insensitive color printing with high color purity and saturation. Additionally, the fabricated metamaterials can be protected by a transparent polymer thin layer for ambient use with further improved color performance. The demonstrated structural color printing with aluminum plasmonic metamaterials offers great potential for relevant applications such as security marking and information storage.

  18. E-print Network Alert Service

    Office of Scientific and Technical Information (OSTI)

    Website Policies and Important Links E-print Web Log alert image About Search Browse by ... and engineering databases and Web sites, based on a search profile you submit to us. ...

  19. E-print Network : User Account

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    New Search | My Selections (0) | | | | Alerts | E-print Network Create User Account User Name: Email Address: I want to: Always receive emails Receive emails if there are new...

  20. Field Facilities Contacts for Printing and Mail | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Field Facilities Contacts for Printing and Mail Field Facilities Contacts for Printing and Mail This is the list of DOE field facilities contacts for Printing and Mail as of April 27, 2011. Go to Mail Services Go to Printing Services Field_Facilities_Contacts_Print-Mail.pdf (74.45 KB) More Documents & Publications Director's Perspective by George Miller Tenant Education and Training Fire Safety Committee Membership List

  1. Minutes from the Print and Mail Managers Exchange Forum Teleconferences |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Minutes from the Print and Mail Managers Exchange Forum Teleconferences Minutes from the Print and Mail Managers Exchange Forum Teleconferences Minutes from the Print and Mail Managers Exchange Forum Teleconferences. Contact the Office of Administrative Management and Support at (202) 586-4318 with any questions. Last updated 01/30/14 Minutes from the November 21, 2013 Printing and Mail Teleconference (8.88 KB) Minutes from the September 19, 2013 Printing and Mail

  2. Minutes from the January 19, 2011 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    January 2010 Printing and Mail Managers Exchange Forum Teleconference Twenty-one individuals participated in the Printing and Mail Managers Exchange Forum, which included Printing and Mail Managers and Contractors Comments/Additions to last Months Minutes No comments. Printing Agenda Items......... Update on the Department-wide FY-2010 Three-Year Plan Dallas Woodruff, Headquarters in formed the group that the Department-wide Printing and Publishing Activities is currently in the concurrence

  3. Minutes from the January 20, 2010 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    , 2010 Printing and Mail Managers Exchange Forum Teleconference Twenty-one individuals participated in the Printing and Mail Managers Exchange Forum, which included Printing and Mail Managers and Contractors. Comments/Additions to last Months Minutes Dallas Woodruff, Headquarters opened the meeting by thanking everyone for participating in the today's teleconference. Printing Agenda Items... Update on the Department-wide Printing and Publishing Activities Report Three-Year Plan. Dallas Woodruff,

  4. Minutes from the July 21, 2010 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    July 21, 2010 Printing and Mail Managers Exchange Forum Teleconference Twenty-one individuals participated in the Printing and Mail Managers Exchange Forum, which included Printing and Mail Managers and Contractors. Comments/Additions to last Months Minutes Dallas Woodruff, Headquarters opened the meeting by thanking everyone for participating in the today's teleconference. Printing Agenda Items... Update on the Government Printing Office revisions to the Standard Form one (SF!), Twenty-five

  5. Argonne's Earth Day 2011

    ScienceCinema

    None

    2016-07-12

    Argonne celebrated Earth Day on April 21, 2011 with an event that featured green activities and information booths.

  6. Earth System Processes

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    earth system processes Earth System Processes Cosmogenic isotopes are rare isotopes created when a high-energy cosmic ray interacts with the nucleus of an atom, causing cosmic ray spallation. These isotopes are produced within earth materials such as rocks or soil, in Earth's atmosphere, and in extraterrestrial items such as meteorites. By measuring cosmogenic isotopes, scientists are able to gain insight into a range of geological and astronomical processes. Cosmogenic nuclides can provide a

  7. Clear-sky and Cloudy Boundary Layers Virendra P. Ghate Argonne National Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Clear-sky and Cloudy Boundary Layers Virendra P. Ghate Argonne National Laboratory Define Boundary Layer Stull (1988) defined the atmospheric boundary layer as "the part of the troposphere that is directly influenced by the presence of the earth's surface, and responds to surface forcings with a time scale of about an hour or less." Typical Boundary Layer Depths and time-scales Scenario Time/Length scale Clear-air Convective 30 mins/1 km Cumulus Topped Boundary Layer 30 mins/1 km

  8. Rare Earth Elements Home Page

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Rare Earth Elements Rare Earth Elements from Coal and Coal By-Products logo. Download the 2016 Rare Earth Elements from Coal and Coal By-Products Project Portfolio Rare Earth ...

  9. Nozzle geometry for organic vapor jet printing

    DOEpatents

    Forrest, Stephen R; McGraw, Gregory

    2015-01-13

    A first device is provided. The device includes a print head. The print head further includes a first nozzle hermetically sealed to a first source of gas. The first nozzle has an aperture having a smallest dimension of 0.5 to 500 microns in a direction perpendicular to a flow direction of the first nozzle. At a distance from the aperture into the first nozzle that is 5 times the smallest dimension of the aperture of the first nozzle, the smallest dimension perpendicular to the flow direction is at least twice the smallest dimension of the aperture of the first nozzle.

  10. E-print Network Alerts -- Energy, science, and technology for...

    Office of Scientific and Technical Information (OSTI)

    Home About Advanced Search Browse by Discipline Scientific Societies E-print Alerts Add E-prints FAQ * HELP * SITE MAP * CONTACT US Enter Search Terms Search Advanced Search

  11. Dai Nippon Printing Co Ltd | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Jump to: navigation, search Name: Dai Nippon Printing Co Ltd Place: Shinjuku-ku, Tokyo, Japan Zip: 162-8001 Sector: Solar Product: Print conglomerate which is involved with...

  12. Novel 3-D Printed Inverters for Electric Vehicles Can Improve...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Novel 3-D Printed Inverters for Electric Vehicles Can Improve EV Power and Efficiency Novel 3-D Printed Inverters for Electric Vehicles Can Improve EV Power and Efficiency April...

  13. Gas cushion control of OVJP print head position

    DOEpatents

    Forrest, Stephen R

    2014-10-07

    An OVJP apparatus and method for applying organic vapor or other flowable material to a substrate using a printing head mechanism in which the print head spacing from the substrate is controllable using a cushion of air or other gas applied between the print head and substrate. The print head is mounted for translational movement towards and away from the substrate and is biased toward the substrate by springs or other means. A gas cushion feed assembly supplies a gas under pressure between the print head and substrate which opposes the biasing of the print head toward the substrate so as to form a space between the print head and substrate. By controlling the pressure of gas supplied, the print head separation from the substrate can be precisely controlled.

  14. The World's Largest 3D Printed Object | Department of Energy

    Energy Saver

    It took 30 hours to print using carbon fiber and composite plastic materials. Using 3D-printing makes the final product cheaper and quicker to manufacture, and it works just as ...

  15. Wind Turbine Manufacturing Transforms with Three-Dimensional Printing |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Turbine Manufacturing Transforms with Three-Dimensional Printing Wind Turbine Manufacturing Transforms with Three-Dimensional Printing May 19, 2016 - 12:57pm Addthis From medical devices to airplane components, three-dimensional (3-D) printing (also called additive manufacturing) is transforming the manufacturing industry. Now, research that supports the Energy Department's Atmosphere to Electrons (A2e) initiative is applying 3-D-printing processes to create wind turbine

  16. Minutes from the March 14, 2013 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    March 14, 2013 Mail discussion Al Majors is on leave today. Ellsworth Howell Jr. and Tony Nellums are sitting for Al. There are no agenda items for the Mail portion. A discussion period for questions, comments, or suggestions was opened without response Printing discussion Discussed suggestions for reducing printing expenses Presidential Executive Order 13589 and reducing hard copy printing in favor of electronic publishing Sec. 5. Printing. Agencies are encouraged to limit the publication and

  17. Minutes from the September 15, 2010 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    September 15, 2010 Printing and Mail Managers Exchange Forum Teleconference Twenty-four individuals participated in the Printing and Mail Managers Exchange Forum, which included Printing and Mail Managers and Contractors. Comments/Additions to last Months Minutes Dallas Woodruff, Headquarters opened the meeting by thanking everyone for participating in the today's teleconference. Printing Agenda Items... Upcoming FY 2010 Department-wide Three-Year Plan Dallas Woodruff, Headquarters informed the

  18. Happy Earth Day 2011!

    Energy.gov [DOE]

    Check out these resources from the Department of Energy to help you celebrate, get in the Earth Day spirit, and take action.

  19. The World's Largest 3D Printed Object | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    The World's Largest 3D Printed Object The World's Largest 3D Printed Object Addthis The Guinness Book of World Records just certified that the Department of Energy's Oak Ridge National Laboratory produced the world's largest solid 3D-printed object

  20. Search over 660,000 E-prints at OSTI's E-print Network | OSTI, US Dept of

    Office of Scientific and Technical Information (OSTI)

    Energy Office of Scientific and Technical Information over 660,000 E-prints at OSTI's E-print Network Back to the OSTI News Listing for 2005 With our latest update, users can now search against a universe of 664,745 e-prints. These e-prints are created within the research laboratories of 18,200 active investigators whose aim is to make sure that their work is readily accessible to interested colleagues and students

  1. Cool Earth Solar

    SciTech Connect

    Lamkin, Rob; McIlroy, Andy; Swalwell, Eric; Rajan, Kish

    2013-04-22

    In a public-private partnership that takes full advantage of the Livermore Valley Open Campus (LVOC) for the first time, Sandia National Laboratories and Cool Earth Solar have signed an agreement that could make solar energy more affordable and accessible. In this piece, representatives from Sandia, Cool Earth Solar, and leaders in California government all discuss the unique partnership and its expected impact.

  2. Cool Earth Solar

    ScienceCinema

    Lamkin, Rob; McIlroy, Andy; Swalwell, Eric; Rajan, Kish

    2016-07-12

    In a public-private partnership that takes full advantage of the Livermore Valley Open Campus (LVOC) for the first time, Sandia National Laboratories and Cool Earth Solar have signed an agreement that could make solar energy more affordable and accessible. In this piece, representatives from Sandia, Cool Earth Solar, and leaders in California government all discuss the unique partnership and its expected impact.

  3. Earth Day 2016

    Energy.gov [DOE]

    April 22, 2016 is the forty-sixth anniversary of the founding of Earth Day which marked the beginning of the modern environmental movement. The Office of Environment, Health, Safety and Security (AU) is leading DOE’s coordinated Earth Day celebrations at the Forrestal DOE Headquarters Building in Washington, D.C.

  4. Earth and Environmental Sciences

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    EES Division Earth and Environmental Sciences We provide solutions to complex problems in climate and environmental change, sustainable energy, and national security. Climate Science Monitoring and studying dynamics between Earth, ecosystems, the atmosphere and climate Sustainable Energy Capturing carbon and researching cleaner, more efficient energy sources Global Security Detecting and predicting threats such as wildfires, earthquakes, and nuclear detonations Repository Science Geoscience,

  5. Cell boundary fault detection system

    DOEpatents

    Archer, Charles Jens; Pinnow, Kurt Walter; Ratterman, Joseph D.; Smith, Brian Edward

    2009-05-05

    A method determines a nodal fault along the boundary, or face, of a computing cell. Nodes on adjacent cell boundaries communicate with each other, and the communications are analyzed to determine if a node or connection is faulty.

  6. Boundary Layer Cloud Turbulence Characteristics

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Boundary Layer Cloud Turbulence Characteristics Virendra Ghate Bruce Albrecht Parameter Observational Readiness (/10) Modeling Need (/10) Cloud Boundaries 9 9 Cloud Fraction Variance Skewness Up/Downdraft coverage Dominant Freq. signal Dissipation rate ??? Observation-Modeling Interface

  7. Earth System Observations

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth Day Earth Day If you do not see the event begin at 3pm ET, please refresh your browser. Are you looking for ways to go green while saving yourself some green? Or are you interested in learning how to incorporate renewable energy options -- like solar, wind and geothermal -- into your home? This Earth Day, hang out with Energy Department experts to learn how you can reduce your energy use, improve your home's comfort and cut your energy bills. We hope you'll join us on April 22 at 3 pm ET

  8. Rare earth gas laser

    DOEpatents

    Krupke, W.F.

    1975-10-31

    A high energy gas laser with light output in the infrared or visible region of the spectrum is described. Laser action is obtained by generating vapors of rare earth halides, particularly neodymium iodide or, to a lesser extent, neodymium bromide, and disposing the rare earth vapor medium in a resonant cavity at elevated temperatures; e.g., approximately 1200/sup 0/ to 1400/sup 0/K. A particularly preferred gaseous medium is one involving a complex of aluminum chloride and neodymium chloride, which exhibits tremendously enhanced vapor pressure compared to the rare earth halides per se, and provides comparable increases in stored energy densities.

  9. BOUndary Plasma Turbulence

    Energy Science and Technology Software Center

    2008-01-25

    BOUT is a parallelized 3D nonlocal electromagnetic turbulence code. The principal calculations are the boundary plasma turbulence in a realistic magnetic geometry. BOUT uses fluid Braginskii equations for plasma vorticity, density, electron and ion temperature and Parallel mementum. With sources added in the core-edge region and sinks in the scrape-off-layer (SOL), BOUT follows the self-consistent profile evolution together with turbulence. BOUT also includes coupling to a magnetohyfrodynamic equlibrium (EFIT package) and a two-dimensional hydrodynamic edgemore » transport model (UEDGE package).« less

  10. A Docking Casette For Printed Circuit Boards

    DOEpatents

    Barringer, Dennis R. (Wallkill, NY); Seminaro, Edward J. (Milton, NY); Toffler, Harold M. (Newburgh, NY)

    2003-08-19

    A docking apparatus for printed circuit boards including a cassette housing, having a housing base, a housing cover and a housing wall, wherein the housing base and the housing wall are disposed relative to each other so as to define a housing cavity for containing a printed circuit board and wherein the housing wall includes a cable opening disposed so as to be communicated with the housing cavity, a linkage mechanism, wherein the linkage mechanism includes an engagement configuration and a disengagement configuration and wherein the linkage mechanism is disposed so as to be associated with the cassette housing and a housing bezel, wherein the housing bezel is disposed relative to the cassette housing so as to be associated with the cable opening.

  11. Solar paint: From synthesis to printing

    DOE PAGES [OSTI]

    Zhou, Xiaojing; Belcher, Warwick; Dastoor, Paul

    2014-11-13

    Water-based polymer nanoparticle dispersions (solar paint) offer the prospect of addressing two of the main challenges associated with printing large area organic photovoltaic devices; namely, how to control the nanoscale architecture of the active layer and eliminate the need for hazardous organic solvents during device fabrication. We review progress in the field of nanoparticulate organic photovoltaic (NPOPV) devices and future prospects for large-scale manufacturing of solar cells based on this technology.

  12. Rework of parylene coated printed wiring assemblies

    SciTech Connect

    Williams, J.O.

    1991-04-01

    This document describes the recommended method for reworking parylene coated Printed Wiring Assemblies (PWAs). Special training is required to successfully rework PWAs that are parylene coated. Parylene coating rework should not be attempted on production units unless successful parylene coating removal has been completed on non-production assemblies. The rework procedures described in this document are recommended for normal parylene rework. Special situations may dictate slight deviation from the methods described herein. 4 figs.

  13. LANL Studies Earth's Magnetosphere

    ScienceCinema

    Daughton, Bill

    2016-07-12

    A new 3-D supercomputer model presents a new theory of how magnetic reconnection works in high-temperature plasmas. This Los Alamos National Laboratory research supports an upcoming NASA mission to study Earth's magnetosphere in greater detail than ever.

  14. Computational Earth Science

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    6 Computational Earth Science We develop and apply a range of high-performance computational methods and software tools to Earth science projects in support of environmental health, cleaner energy, and national security. Contact Us Group Leader Carl Gable Deputy Group Leader Gilles Bussod Email Profile pages header Search our Profile pages Hari Viswanathan inspects a microfluidic cell used to study the extraction of hydrocarbon fuels from a complex fracture network. EES-16's Subsurface Flow

  15. Unveiled: Earth's Viral Diversity

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Unveiled: Earth's Viral Diversity Unveiled: Earth's Viral Diversity NERSC Resources Help Researchers Identify 125,000 New Viral Sequences in Environmental Datasets August 17, 2016 Contact: David Gilbert, degilbert@lbl.gov, 925-296-5643 virome graphic art by Z Rostomian LBNL DOE JGI researchers utilized the largest collection of assembled metagenomic datasets from around the world to uncover over 125,000 partial and complete viral genomes, the majority of them infecting microbes. Graphic by Zosia

  16. Lab celebrates Earth Day

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Lab celebrates Earth Day Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:November 2, 2016 all issues All Issues » submit Lab celebrates Earth Day Multiple activities focus on environmental protection. May 1, 2013 A team from Industrial Hygiene and Safety during the Great Garbage Grab A team from Industrial Hygiene and Safety during the Great Garbage Grab. Contact Editor Linda Anderman Email Community Programs Office Kurt Steinhaus

  17. 3D Printed Car at the International Manufacturing Technology Show |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy 3D Printed Car at the International Manufacturing Technology Show 3D Printed Car at the International Manufacturing Technology Show Addthis WORLD&#039;S FIRST 1 of 6 WORLD'S FIRST The world's first 3D-printed car on display at the International Manufacturing Technology Show in Chicago last week. Arizona-based Local Motors, and Cincinnati Incorporated teamed with Oak Ridge National Laboratory's Manufacturing Demonstration Facility-with funding support from the Energy

  18. Minutes from the October 26, 2011 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    October 26, 2011 Printing and Mail Managers Exchange Forum Teleconference Comments/Additions to last Months Minutes No comments. Please note the teleconference minutes were not electronically recorded as in the past. The minutes only consist of information provided to the group by Alvan Majors and Dallas Woodruff of Headquarters on topics listed in the agenda and not any follow-up questions. Printing Agenda Items......... Printing and Publishing Activities Report "Three-Year Plan: Dallas

  19. Good Earths and Rare Earths | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Good Earths and Rare Earths Good Earths and Rare Earths April 20, 2011 - 6:17pm Addthis Charles Rousseaux Charles Rousseaux Senior Communications Specialist (detailee) What does this mean for me? Rare earth elements -- dysprosium, neodymium, terbium, europium and yttrium -- are essential to a wide range of green energy technologies ranging from windmills to electric vehicles One of their primary uses is in permanent magnets, which amount to over a $4 billion global industry Ames Laboratory

  20. Modeling the earth system

    SciTech Connect

    Ojima, D.

    1992-12-31

    The 1990 Global Change Institute (GCI) on Earth System Modeling is the third of a series organized by the Office for Interdisciplinary Earth Studies to look in depth at particular issues critical to developing a better understanding of the earth system. The 1990 GCI on Earth System Modeling was organized around three themes: defining critical gaps in the knowledge of the earth system, developing simplified working models, and validating comprehensive system models. This book is divided into three sections that reflect these themes. Each section begins with a set of background papers offering a brief tutorial on the subject, followed by working group reports developed during the institute. These reports summarize the joint ideas and recommendations of the participants and bring to bear the interdisciplinary perspective that imbued the institute. Since the conclusion of the 1990 Global Change Institute, research programs, nationally and internationally, have moved forward to implement a number of the recommendations made at the institute, and many of the participants have maintained collegial interactions to develop research projects addressing the needs identified during the two weeks in Snowmass.

  1. E-print Network home page -- Energy, science, and technology...

    Office of Scientific and Technical Information (OSTI)

    Energy, science, and technology for the research community Enter Search Terms Search Advanced Search The E-print Network is . . . . . . a vast, integrated network of electronic ...

  2. DOE fundamentals handbook: Engineering symbology, prints, and drawings. Volume 1

    SciTech Connect

    Not Available

    1993-01-01

    The Engineering Symbology, Prints, and Drawings Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and technical staff with the necessary fundamentals training to ensure a basic understanding of engineering prints, their use, and their function. The handbook includes information on engineering fluid drawings and prints; piping and instrument drawings; major symbols and conventions; electronic diagrams and schematics; logic circuits and diagrams; and fabrication, construction, and architectural drawings. This information will provide personnel with a foundation for reading, interpreting, and using the engineering prints and drawings that are associated with various DOE nuclear facility operations and maintenance.

  3. DOE fundamentals handbook: Engineering symbology, prints, and drawings

    SciTech Connect

    Not Available

    1993-01-01

    The Engineering Symbology, Prints, and Drawings Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and technical staff with the necessary fundamentals training to ensure a basic understanding of engineering prints, their use, and their function. The handbook includes information on engineering fluid drawings and prints; piping and instrument drawings; major symbols and conventions; electronic diagrams and schematics; logic circuits and diagrams; and fabrication, construction, and architectural drawings. This information will provide personnel with a foundation for reading, interpreting, and using the engineering prints and drawings that are associated with various DOE nuclear facility operations and maintenance.

  4. DOE fundamentals handbook: Engineering symbology, prints, and drawings. Volume 2

    SciTech Connect

    Not Available

    1993-01-01

    The Engineering Symbology, Prints, and Drawings Handbook was developed to assist nuclear facility operating contractors in providing operators, maintenance personnel, and technical staff with the necessary fundamentals training to ensure a basic understanding of engineering prints, their use, and their function. The handbook includes information on engineering fluid drawings and prints; piping and instrument drawings; major symbols and conventions; electronic diagrams and schematics; logic circuits and diagrams; and fabrication, construction, and architectural drawings. This information will provide personnel with a foundation for reading, interpreting, and using the engineering prints and drawings that are associated with various DOE nuclear facility operations and maintenance.

  5. 3D Printing a Classic | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3D Printing a Classic 3D Printing a Classic January 15, 2015 - 4:02pm Addthis The team from the Oak Ridge Manufacturing Demonstration Facility is at the Detroit Auto Show this week to display their latest accomplishment: a 3D-printed, electric-motor driven, Shelby Cobra. In just six weeks, the team went from designing the car in digital models, to 3D printing the frame and other parts with fiber-reinforced composite material, to assembling, finishing, and painting the final product. President

  6. Energy Department Unveils 3D-Printed Building; New Initiatives...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    ... Energy Department Unveils 3D-Printed Building; New Initiatives During Industry Day DOE Announces JUMP Initiative Winners, Launches New Crowdsourcing Calls at Bay Area Maker Faire

  7. Making 3D Printed Christmas Ornaments | GE Global Research

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Check out the video featuring Juan Pablo Cilia, a Rapid Prototyping Specialist in the ... Santa's sleigh becomes "Intelligent Machine" this Christmas Using 3D Printing to Redesign ...

  8. Silver Ink for Conductor Printing - Energy Innovation Portal

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    flake suspended in a suitable solvent amenable to printing. These silver metal suspension formulations require high processing temperatures to sinter the particles (180 C)....

  9. Structural color printing based on plasmonic metasurfaces of...

    Office of Scientific and Technical Information (OSTI)

    Moreover, the fabricated metasurfaces can be protected with a protective coating for ambient use without degrading performances. The demonstrated structural color printing platform ...

  10. W7 printing from VISITOR network

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    W4, Federal Withholding Tax Form W4, Federal Withholding Tax Form W4, Federal Withholding Tax Form (104.8 KB) More Documents & Publications Employee In-Processing Forms DOE F 1500.7 PSH-16-0069 - In the Matter of Personnel Security Hearing

    W7 printing from VISITOR network Last Modified by Jerry Camuso, 02/12/2015. 1 . From the "start menu", click on "Devices and Printers" 2. Click on "Add a printer" and choose "Add a local printer". 3 . Choose

  11. Google Earth Tour: Water reuse at LANL

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Google Earth Tour: Water reuse at LANL Google Earth Tour: Water reuse at LANL

  12. Earth shelter goes international

    SciTech Connect

    Boyer, L.L.

    1983-06-01

    Since the mid-1970's earth sheltered buildings in the US have become more numerous and important as a contemporary passive building concept. Further, an intense international interest has now developed, as evidenced by a number of important activities. One of these events is the 1983 International Conference on Energy Efficient Buildings with Earth Shelter Protection to be conducted during 1-6 August in Sydney, Australia. A review of past activities leading up to this event, as well as a brief review of the conference program, is the subject of this discussion.

  13. Earth sheltered housing phenomenon

    SciTech Connect

    Boyer, L.L.

    1981-06-21

    Both national and international attention has recently been focused on earth sheltered construction as an emerging energy alternative. This is especially true for the High Plains region of the central United States. Traditionally, inhabitants of this region have been sensitized to the need for windstorm protection. However, the dramatic potentials for energy savings have served as a strong secondary inducement to the burgeoning construction activity in what is now viewed as a contemporary dwelling concept. The typical characteristics of such dwellings are reviewed as well as the educational challenge awaiting professional input to this developing boom in earth sheltered construction. 12 refs.

  14. In Situ X-Ray Scattering Helps Optimize Printed Solar Cells

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    In Situ X-Ray Scattering Helps Optimize Printed Solar Cells In Situ X-Ray Scattering Helps Optimize Printed Solar Cells Print Wednesday, 25 February 2015 00:00 Plastic solar cells...

  15. In Situ X-Ray Scattering Helps Optimize Printed Solar Cells

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    In Situ X-Ray Scattering Helps Optimize Printed Solar Cells Print Plastic solar cells that can be printed on flexible sheets with an ink-like solution show a lot of potential as a...

  16. Cell boundary fault detection system

    DOEpatents

    Archer, Charles Jens; Pinnow, Kurt Walter; Ratterman, Joseph D.; Smith, Brian Edward

    2011-04-19

    An apparatus and program product determine a nodal fault along the boundary, or face, of a computing cell. Nodes on adjacent cell boundaries communicate with each other, and the communications are analyzed to determine if a node or connection is faulty.

  17. Fact #804: November 18, 2013 Tool Available to Print Used Vehicle...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Available to Print Used Vehicle Fuel Economy Window Stickers Fact 804: November 18, 2013 Tool Available to Print Used Vehicle Fuel Economy Window Stickers Because used vehicle ...

  18. 2016 Rare Earth Elements Workshop Accelerating Rare Earth Element...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Rare Earth Elements Workshop Accelerating Rare Earth Element Recovery from U.S. Domestic Sources of Coal and Coal By-Products August 8-9, 2016 Hosted by: Dr. Cynthia Powell Acting ...

  19. NASA Earth at Night Video

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ... Twitter Google + Vimeo GovDelivery SlideShare NASA Earth at Night Video HomeEC, Energy, Energy Efficiency, Global, Modeling, News & Events, Solid-State Lighting, VideosNASA Earth ...

  20. Earth's Decelerating Tectonic Plates

    SciTech Connect

    Forte, A M; Moucha, R; Rowley, D B; Quere, S; Mitrovica, J X; Simmons, N A; Grand, S P

    2008-08-22

    Space geodetic and oceanic magnetic anomaly constraints on tectonic plate motions are employed to determine a new global map of present-day rates of change of plate velocities. This map shows that Earth's largest plate, the Pacific, is presently decelerating along with several other plates in the Pacific and Indo-Atlantic hemispheres. These plate decelerations contribute to an overall, globally averaged slowdown in tectonic plate speeds. The map of plate decelerations provides new and unique constraints on the dynamics of time-dependent convection in Earth's mantle. We employ a recently developed convection model constrained by seismic, geodynamic and mineral physics data to show that time-dependent changes in mantle buoyancy forces can explain the deceleration of the major plates in the Pacific and Indo-Atlantic hemispheres.

  1. Superhydrophobic diatomaceous earth

    DOEpatents

    Simpson, John T.; D'Urso, Brian R.

    2012-07-10

    A superhydrophobic powder is prepared by coating diatomaceous earth (DE) with a hydrophobic coating on the particle surface such that the coating conforms to the topography of the DE particles. The hydrophobic coating can be a self assembly monolayer of a perfluorinated silane coupling agent. The DE is preferably natural-grade DE where organic impurities have been removed. The superhydrophobic powder can be applied as a suspension in a binder solution to a substrate to produce a superhydrophobic surface on the substrate.

  2. Holding Mother Earth Sacred

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Holding Mother Earth Sacred Photo Journal Project Resource List 2010 Mountain and Plains Education and Research Center, Ken Scott: http://maperc.ucdenver.edu/ UC Denver Office of Diversity and Inclusion, Anschutz Medical Center, Dominic Martinez: www.ucdenver.edu Colorado School of Public Health: www.ucdenver.edu/academics/colleges/PublicHealth/Pages/welcome.aspx University of Colorado Denver: www.ucdenver.edu National Institute of Occupational Safety and Health (NIOSH): www.cdc.gov/niosh

  3. Earth and Environmental Sciences

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth and Environmental Sciences Our Vision National User Facilities Research Areas In Focus Global Solutions ⇒ Navigate Section Our Vision National User Facilities Research Areas In Focus Global Solutions Climate and Ecosystem Sciences Division The Climate and Ecosystem Sciences Division seeks to translate data from advanced laboratories, experiments, and large field stations into better tools for predicting the implications of climatic change for our natural environment and for critical

  4. Ames Lab 101: Rare Earths

    SciTech Connect

    Gschneidner, Karl

    2010-01-01

    "Mr. Rare Earth," Ames Laboratory scientist Karl Gschneidner Jr., explains the importance of rare-earth materials in many of the technologies we use today -- ranging from computers to hybrid cars to wind turbines. Gschneidner is a world renowned rare-earths expert at the U.S. Department of Energy's Ames Laboratory.

  5. Ames Lab 101: Rare Earths

    ScienceCinema

    Gschneidner, Karl

    2012-08-29

    "Mr. Rare Earth," Ames Laboratory scientist Karl Gschneidner Jr., explains the importance of rare-earth materials in many of the technologies we use today -- ranging from computers to hybrid cars to wind turbines. Gschneidner is a world renowned rare-earths expert at the U.S. Department of Energy's Ames Laboratory.

  6. LLNL-Earth3D

    Energy Science and Technology Software Center

    2013-10-01

    Earth3D is a computer code designed to allow fast calculation of seismic rays and travel times through a 3D model of the Earth. LLNL is using this for earthquake location and global tomography efforts and such codes are of great interest to the Earth Science community.

  7. Pyramidal inversion domain boundaries revisited

    SciTech Connect

    Remmele, T.; Albrecht, M.; Irmscher, K.; Fornari, R.; Strassburg, M.

    2011-10-03

    The structure of pyramidal inversion domain boundaries in GaN:Mg was investigated by aberration corrected transmission electron microscopy. The analysis shows the upper (0001) boundary to consist of a single Mg layer inserted between polarity inverted GaN layers in an abcab stacking. The Mg bound in these defects is at least one order of magnitude lower than the chemical Mg concentration. Temperature dependent Hall effect measurements show that up to 27% of the Mg acceptors is electrically compensated.

  8. Rare Earth Metals & Alloys | The Ames Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Rare Earth Metals & Alloys Quantities of high-purity rare earth metals and alloys in ... storage, cutting and cleaning and SDS information for the rare earth elements (metals).

  9. Suitability for 3D Printed Parts for Laboratory Use

    SciTech Connect

    Zwicker, Andrew P.; Bloom, Josh; Albertson, Robert; Gershman, Sophia

    2014-08-01

    3D printing has become popular for a variety of users, from industrial to the home hobbyist, to scientists and engineers interested in producing their own laboratory equipment. In order to determine the suitability of 3D printed parts for our plasma physics laboratory, we measured the accuracy, strength, vacuum compatibility, and electrical properties of pieces printed in plastic. The flexibility of rapidly creating custom parts has led to the 3D printer becoming an invaluable resource in our laboratory and is equally suitable for producing equipment for advanced undergraduate laboratories.

  10. Earth-sheltered apartments

    SciTech Connect

    Germer, J.

    1984-12-01

    Earth-sheltered apartments for students at St. Johns University, Collegeville, MN are described. The intent was to provide energy-efficient, low maintenance housing in a neighborhood environment for the students. Students would learn about energy-conscious architecture from living in the buildings. The buildings have had few problems, but energy performance has not been up to expectations. The consumption of electricity exceeded predictions by 49%. The most likely answer to the problem is deviation from design. Several items of energy-efficient design were specified but deleted in order to cut costs.

  11. A Star on Earth

    ScienceCinema

    Prager, Stewart; Zwicker, Andrew; Hammet, Greg; Tresemer, Kelsey; Diallo, Ahmed

    2016-07-12

    At the Energy Department's Princeton Plasma Physics Lab, scientists are trying to accomplish what was once considered the realm of science fiction: create a star on Earth. The National Spherical Torus Experiment (NSTX) is a magnetic fusion device that is used to study the physics principles of spherically shaped plasmas -- hot ionized gases in which, under the right conditions, nuclear fusion will occur. Fusion is the energy source of the sun and all of the stars. Not just limited to theoretical work, the NSTX is enabling cutting-edge research to develop fusion as a future energy source.

  12. A Star on Earth

    SciTech Connect

    Prager, Stewart; Zwicker, Andrew; Hammet, Greg; Tresemer, Kelsey; Diallo, Ahmed

    2014-03-05

    At the Energy Department's Princeton Plasma Physics Lab, scientists are trying to accomplish what was once considered the realm of science fiction: create a star on Earth. The National Spherical Torus Experiment (NSTX) is a magnetic fusion device that is used to study the physics principles of spherically shaped plasmas -- hot ionized gases in which, under the right conditions, nuclear fusion will occur. Fusion is the energy source of the sun and all of the stars. Not just limited to theoretical work, the NSTX is enabling cutting-edge research to develop fusion as a future energy source.

  13. Earth Day 2016 | Department of Energy

    Office of Environmental Management (EM)

    Earth Day 2016 Earth Day 2016 April 18, 2016 - 7:39am Addthis Earth Day 2016 April 22, 2016 is the forty-sixth anniversary of the founding of Earth Day which marked the beginning ...

  14. Instructions to Print Monthly P-card Statement

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    to Print Monthly P-card Statement 1. Go to Website https:gov1.paymentnet.com and login with your Organization ID, User ID and Pass Phrase. Organization ID is doe0001. User ID and...

  15. A Unix Print Filter for Controlling an HP Laserjet Printer

    SciTech Connect

    Hoffman, F.M.

    1992-01-01

    This report describes a Unix print filter designed to control an Hewlett Packard Laserjet or other printer that uses Hewlett Packard's Printer Control Language (HP-PCL). The filter gives users the ability to control print pitch, orientation, and indentation by using standard flags to the Unix lpr command or multiple entries in the /etc/printcap file and allows both ascii and binary (i.e., graphics and down-loadable fonts) files to be printed. Additionally, the filter provides some accounting capability. The supported print pitch and orientation options are described, as are the different configuration options. The code for the filter is included in Appendix A and sample entries for the /etc/printcap file are included in Appendix B and C.

  16. Printing 3D Catalytic Devices | The Ames Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Printing 3D Catalytic Devices An error occurred. Try watching this video on www.youtube.com, or enable JavaScript if it is disabled in your browser. Ames Laboratory scientist Igor...

  17. Printed decorative solar panels could become part of our homes...

    OpenEI (Open Energy Information) [EERE & EIA]

    content Printed decorative solar panels could become part of our homes and offices Hello, I provide user supp... The top one on this page: htt... Can you send the specific...

  18. 3D Printing Enables New Generation of Heat Exchangers

    Energy.gov [DOE]

    Three-dimensional printing is revolutionizing how we manufacture objects in almost every industry—from vehicles to medical devices to biotech. Now, the University of Maryland, through a partnership...

  19. Printing a Car: A Team Effort in Innovation

    Office of Energy Efficiency and Renewable Energy (EERE)

    Oak Ridge National Lab's work with Local Motors to build a 3D-printed car was highlighted at the International Manufacturing Technology Show (IMTS) in September 2014 with a live demonstration.

  20. Future of 3D Printing | GE Global Research

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    In 2016, GE will enter a new jet engine into service called the CFM LEAP-the first in GE's line to incorporate 3D-printed parts. Specifically, it will be a combustion component ...

  1. Browse by Discipline -- E-print Network Subject Pathways: Fission...

    Office of Scientific and Technical Information (OSTI)

    K L M N O P Q R S T U V W X Y Z Optimization Online, An E-Print Site for the Optimization Community Oregon State University, Department of Mathematics, Vector Calculus Gap Project

  2. Earth sheltered structures

    SciTech Connect

    Boyer, L.L.

    1982-01-01

    The earth shelter concept has been utilized successfully around the world for thousands of years, but its use with contemporary mechanically conditioned buildings dates only from the oil embargo of the mid-1970s. This is an architectural innovation and a growing and viable response to the energy imperative. Most of the technical problems of earth shelters have been effectively addressed, but a systems design approach could further enhance overall energy savings. Although occupant lifestyle seems to be at a high level, areas that require further attention include site design, daylighting, and refined thermal design. The proper integration of passive solar heating and disaster protection represent opportunities for improved multifunctional aspects. With proper design, annual heating and cooling energy use reductions on the order of 80% can be anticipated. Research on energy design refinements and occupancy aspects necessary to achieve such levels of savings is presently under way at Oklahoma State University, the University of Minnesota, and other study centers throughout the nation and the world.

  3. Transforming Wind Turbine Blade Mold Manufacturing with 3D Printing |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Transforming Wind Turbine Blade Mold Manufacturing with 3D Printing Transforming Wind Turbine Blade Mold Manufacturing with 3D Printing A screenshot of the cover of the 3D blade manufacturing brochure. Innovation in the design and manufacturing of wind power generation components continues to be critical to achieving our national goals. As a result of this challenge, the U.S. Department of Energy's Wind Program and Advanced Manufacturing Office are partnering with public

  4. Researchers 3D print ultralight supercapacitors | National Nuclear Security

    National Nuclear Security Administration (NNSA)

    Administration | (NNSA) 3D print ultralight supercapacitors Monday, February 22, 2016 - 12:00am NNSA Blog The micro-architectured, ultra-lightweight supercapacitor material is able to retain energy on par with those made with electrodes 10 to 100 times thinner. For the first time ever, scientists at Lawrence Livermore National Laboratory and UC Santa Cruz have successfully 3D-printed supercapacitors using an ultra-lightweight graphene aerogel, opening the door to novel, unconstrained designs

  5. Energy Department Earth Week 2015

    Energy.gov [DOE]

    To celebrate Earth Week and Earth Day, the Bioenergy Technologies Office (BETO) is participating in several Energy Department activities! Look for us inside the lobby of the U.S. Department of Energy Forrestal Building in Washington, D.C., from April 13–17. Then, on Earth Day, April 22, everyone is welcome to join us outside on the Forrestal West Plaza for Community Day!

  6. Earth Week 2008 | Jefferson Lab

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth Week 2008 Day 1 Day 1: Earth Day Every Day - Jefferson Lab observes Earth Day every day with its business practices. Recycling Centers for paper, batteries, toner cartridges, aluminum cans and plastic bottles are distributed throughout the site, and scrap metal and other lab industrial waste is recycled. In procurements, the stockroom offers an array of recycled options and encourages the purchase of recycled and recyclable products. And motion-sensor lighting reduces power use in empty

  7. Geoengineering the Earth's Climate

    ScienceCinema

    Google Tech Talks

    2016-07-12

    Emergency preparedness is generally considered to be a good thing, yet there is no plan regarding what we might do should we be faced with a climate emergency. Such an emergency could take the form of a rapid shift in precipitation patterns, a collapse of the great ice sheets, the imminent triggering of strong climate system feedbacks, or perhaps the loss of valuable ecosystems. Over the past decade, we have used climate models to investigate the potential to reverse some of the effects of greenhouse gases in the atmosphere by deflecting some incoming sunlight back to space. This would probably be most cost-effectively achieved with the placement of small particles in or above the stratosphere. Our model simulations indicate that such geoengineering approaches could potentially bring our climate closer to the state is was in prior to the introduction of greenhouse gases. This talk will present much of what is known about such geoengineering approaches, and raise a range of issues likely to stimulate lively discussion. Speaker: Ken Caldeira Ken Caldeira is a scientist at the Carnegie Institution Department of Global Ecology and a Professor (by courtesy) at the Stanford University Department of Environmental and Earth System Sciences. Previously, he worked for 12 years in the Energy and Environment Directorate at the Lawrence Livermore National Laboratory (Department of Energy). His research interests include the numerical simulation of Earth's climate, carbon, and biogeochemistry; ocean acidification; climate emergency response systems; evaluating approaches to supplying environmentally-friendly energy services; ocean carbon sequestration; long-term evolution of climate and geochemical cycles; and marine biogeochemical cycles. Caldeira has a B.A. in Philosophy from Rutgers College and an M.S. and Ph.D. in Atmospheric Sciences from New York University.

  8. Phase stable rare earth garnets

    SciTech Connect

    Kuntz, Joshua D.; Cherepy, Nerine J.; Roberts, Jeffery J.; Payne, Stephen A.

    2013-06-11

    A transparent ceramic according to one embodiment includes a rare earth garnet comprising A.sub.hB.sub.iC.sub.jO.sub.12, where h is 3.+-.10%, i is 2.+-.10%, and j is 3.+-.10%. A includes a rare earth element or a mixture of rare earth elements, B includes at least one of aluminum, gallium and scandium, and C includes at least one of aluminum, gallium and scandium, where A is at a dodecahedral site of the garnet, B is at an octahedral site of the garnet, and C is at a tetrahedral site of the garnet. In one embodiment, the rare earth garment has scintillation properties. A radiation detector in one embodiment includes a transparent ceramic as described above and a photo detector optically coupled to the rare earth garnet.

  9. Browse by Discipline -- E-print Network Subject Pathways: Biotechnolog...

    Office of Scientific and Technical Information (OSTI)

    ... Ben (Ben Marzeion) - Institut fr Geographie, Universitt Innsbruck Masiello, Carrie (Carrie Masiello) - Department of Earth Science, Rice University Maslowski, Wieslaw ...

  10. Browse by Discipline -- E-print Network Subject Pathways: Power...

    Office of Scientific and Technical Information (OSTI)

    - Centro de Investigaciones en Ecosistemas, Universidad Nacional Autnoma de Mxico Quinn, Nigel (Nigel Quinn) - Earth Sciences Division, Lawrence Berkeley National ...

  11. Optical systems fabricated by printing-based assembly

    DOEpatents

    Rogers, John; Nuzzo, Ralph; Meitl, Matthew; Menard, Etienne; Baca, Alfred J.; Motala, Michael; Ahn, Jong-Hyun; Park, Sang-II; Yu; Chang-Jae; Ko, Heung-Cho; Stoykovich; Mark; Yoon, Jongseung

    2011-07-05

    Provided are optical devices and systems fabricated, at least in part, via printing-based assembly and integration of device components. In specific embodiments the present invention provides light emitting systems, light collecting systems, light sensing systems and photovoltaic systems comprising printable semiconductor elements, including large area, high performance macroelectronic devices. Optical systems of the present invention comprise semiconductor elements assembled, organized and/or integrated with other device components via printing techniques that exhibit performance characteristics and functionality comparable to single crystalline semiconductor based devices fabricated using conventional high temperature processing methods. Optical systems of the present invention have device geometries and configurations, such as form factors, component densities, and component positions, accessed by printing that provide a range of useful device functionalities. Optical systems of the present invention include devices and device arrays exhibiting a range of useful physical and mechanical properties including flexibility, shapeability, conformability and stretchablity.

  12. Optical systems fabricated by printing-based assembly

    DOEpatents

    Rogers, John; Nuzzo, Ralph; Meitl, Matthew; Menard, Etienne; Baca, Alfred; Motala, Michael; Ahn, Jong -Hyun; Park, Sang -Il; Yu, Chang -Jae; Ko, Heung Cho; Stoykovich, Mark; Yoon, Jongseung

    2015-08-25

    Provided are optical devices and systems fabricated, at least in part, via printing-based assembly and integration of device components. In specific embodiments the present invention provides light emitting systems, light collecting systems, light sensing systems and photovoltaic systems comprising printable semiconductor elements, including large area, high performance macroelectronic devices. Optical systems of the present invention comprise semiconductor elements assembled, organized and/or integrated with other device components via printing techniques that exhibit performance characteristics and functionality comparable to single crystalline semiconductor based devices fabricated using conventional high temperature processing methods. Optical systems of the present invention have device geometries and configurations, such as form factors, component densities, and component positions, accessed by printing that provide a range of useful device functionalities. Optical systems of the present invention include devices and device arrays exhibiting a range of useful physical and mechanical properties including flexibility, shapeability, conformability and stretchablity.

  13. Optical systems fabricated by printing-based assembly

    DOEpatents

    Rogers, John; Nuzzo, Ralph; Meitl, Matthew; Menard, Etienne; Baca, Alfred J; Motala, Michael; Ahn, Jong-Hyun; Park, Sang-Il; Yu, Chang-Jae; Ko, Heung Cho; Stoykovich, Mark; Yoon, Jongseung

    2014-05-13

    Provided are optical devices and systems fabricated, at least in part, via printing-based assembly and integration of device components. In specific embodiments the present invention provides light emitting systems, light collecting systems, light sensing systems and photovoltaic systems comprising printable semiconductor elements, including large area, high performance macroelectronic devices. Optical systems of the present invention comprise semiconductor elements assembled, organized and/or integrated with other device components via printing techniques that exhibit performance characteristics and functionality comparable to single crystalline semiconductor based devices fabricated using conventional high temperature processing methods. Optical systems of the present invention have device geometries and configurations, such as form factors, component densities, and component positions, accessed by printing that provide a range of useful device functionalities. Optical systems of the present invention include devices and device arrays exhibiting a range of useful physical and mechanical properties including flexibility, shapeability, conformability and stretchablity.

  14. High Poisson;s ratio of Earth;s inner core explained by carbon...

    Office of Scientific and Technical Information (OSTI)

    High Poisson;s ratio of Earth;s inner core explained by carbon alloying Citation Details In-Document Search Title: High Poisson;s ratio of Earth;s inner core explained by carbon ...

  15. Spin transition zone in Earth;s lower mantle (Journal Article...

    Office of Scientific and Technical Information (OSTI)

    Spin transition zone in Earth;s lower mantle Citation Details In-Document Search Title: Spin transition zone in Earth;s lower mantle Authors: Lin, J.-F. ; Vanko, G. ; Jacobsen, ...

  16. Observations of solar wind penetration into the earth's magnetosphere - the plasma mantle

    SciTech Connect

    Sanchez, E.R.; Meng, Chingi; Newell, P.T. )

    1990-12-01

    The large database provided by the continuous coverage of the Defense Meteorogical Satellite Program polar orbiting satellites constitutes an important source of information on particle precipitation in the ionosphere. This information can be used to monitor and map the earth's magnetosphere (the cavity around the earth that forms as the stream of particles and magnetic field ejected from the sun, known as the solar wind, encounters the earth's magnetic field) and for a large variety of statistical studies of its morphology and dynamics. The boundary between the magnetosphere and the solar wind is presumably open in some places and at some times, thus allowing the direct entry of solar-wind plasma into the magnetosphere through a boundary layer known as the plasma mantle. The preliminary results of a statistical study of the plasma-mantle precipitation in the inosphere are presented. The first quantitative mapping of the ionospheric region where the plasma-mantle particles precipitate is obtained. 12 refs.

  17. High density printed electrical circuit board card connection system

    DOEpatents

    Baumbaugh, Alan E.

    1997-01-01

    A zero insertion/extraction force printed circuit board card connection system comprises a cam-operated locking mechanism disposed along an edge portion of the printed circuit board. The extrusions along the circuit board mate with an extrusion fixed to the card cage having a plurality of electrical connectors. The card connection system allows the connectors to be held away from the circuit board during insertion/extraction and provides a constant mating force once the circuit board is positioned. The card connection system provides a simple solution to the need for a greater number of electrical signal connections.

  18. 3D Printing Comes of Age | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    D Printing Comes of Age 3D Printing Comes of Age September 19, 2014 - 5:25pm Addthis The highlight of this year's International Manufacturing Technology Show (IMTS), held earlier in September at the McCormick Place Convention Center in Chicago, IL, was the electric car produced live during the Show. More than 110,000 people witnessed the representatives from Cincinnati Incorporated-a 115-year-old industrial machine manufacturer from Ohio, Local Motors-a new creative manufacturing Arizona

  19. High density printed electrical circuit board card connection system

    DOEpatents

    Baumbaugh, A.E.

    1997-05-06

    A zero insertion/extraction force printed circuit board card connection system comprises a cam-operated locking mechanism disposed along an edge portion of the printed circuit board. The extrusions along the circuit board mate with an extrusion fixed to the card cage having a plurality of electrical connectors. The card connection system allows the connectors to be held away from the circuit board during insertion/extraction and provides a constant mating force once the circuit board is positioned. The card connection system provides a simple solution to the need for a greater number of electrical signal connections. 12 figs.

  20. Toward integrated PV panels and power electronics using printing technologies

    SciTech Connect

    Ababei, Cristinel; Yuvarajan, Subbaraya; Schulz, Douglas L.

    2010-07-15

    In this paper, we review the latest developments in the area of printing technologies with an emphasis on the fabrication of control-embedded photovoltaics (PV) with on-board active and passive devices. We also review the use of power converters and maximum power point tracking (MPPT) circuits with PV panels. Our focus is on the investigation of the simplest implementations of such circuits in view of their integration with solar cells using printing technologies. We see this concept as potentially enabling toward further cost reduction. Besides a discussion as to feasibility, we shall also present some projections and guidelines toward possible integration. (author)

  1. VenEarth Group | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    VenEarth Group Jump to: navigation, search Name: VenEarth Group Place: San Francisco, California Product: San Francisco-based venture capital company. References: VenEarth Group1...

  2. Celebrate Earth Day! | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Savers Facebook pages, our Earth Day poll provides another opportunity for you to interact with us. Log on to our Earth Day Web site and tell us how you'll recognize Earth Day,...

  3. Earth Day 2014 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    This year, we're celebrating Earth Day all week long. It's Earth Week on Energy.gov We're focusing on climate change, highlighting Earth Day events and sharing ways Americans ...

  4. Install the E-print Network toolbar -- Energy, science, and technology...

    Office of Scientific and Technical Information (OSTI)

    Home About Advanced Search Browse by Discipline Scientific Societies E-print Alerts Add E-prints FAQ * HELP * SITE MAP * CONTACT US Enter Search Terms Search Advanced Search

  5. EATON PURSUES PRINT-BASED MANUFACTURING OF INTEGRATED, LOW-COST...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    INTEGRATED, LOW-COST, HIGH-PERFORMANCE SSL LUMINAIRES EATON PURSUES PRINT-BASED MANUFACTURING OF INTEGRATED, LOW-COST, HIGH-PERFORMANCE SSL LUMINAIRES Print-based Manufacturing of ...

  6. Local Motors Begins Their Six Day Quest to 3D Print the 'Strati...

    Energy.gov [DOE] (indexed site)

    to 3D print a car at the September 2014 International Manufacturing Technology Show. Local Motors Begins Their Six Day Quest to 3D Print the 'Strati' Car Live at IMTS (470.83 ...

  7. E-print Network Web Log News: Research Communications for Scientists...

    Office of Scientific and Technical Information (OSTI)

    Weve had a number of inquiries about how to best search our E-prints on Web-sites feature for individual authors. Heres what you do. First be sure that the E-prints on Web ...

  8. ENG-Canada-USA Government Procurement (clean 11 Feb 2010 printed...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    ENG-Canada-USA Government Procurement (clean 11 Feb 2010 printed) ENG-Canada-USA Government Procurement (clean 11 Feb 2010 printed) ENG-Canada-USA Government Procurement (clean 11 ...

  9. EERE Success Story-Novel 3-D Printed Inverters for Electric Vehicles...

    Energy Saver

    April 28, 2015 - 2:02pm Addthis 3-D Printed Inverter 3-D Printed Inverter Plug-in electric vehicle technologies are on their way to being even lighter, more powerful and more ...

  10. Intense X-rays expose tiny flaws in 3-D printed titanium that...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    For 3-D printing, metals are usually atomized into powders first. Ti-6Al-4V powders are printed by using either selective laser melting or electron-beam melting (EBM), which is the ...

  11. OSTI's E-print Network content tops 900,000 documents | OSTI...

    Office of Scientific and Technical Information (OSTI)

    than 22,000 scientific e-print Web sites. In addition, the E-print Network provides links to more than 2,900 relevant scientific societies. This Web portal, established as the ...

  12. Earth analysis methods, subsurface feature detection methods, earth analysis devices, and articles of manufacture

    DOEpatents

    West, Phillip B.; Novascone, Stephen R.; Wright, Jerry P.

    2012-05-29

    Earth analysis methods, subsurface feature detection methods, earth analysis devices, and articles of manufacture are described. According to one embodiment, an earth analysis method includes engaging a device with the earth, analyzing the earth in a single substantially lineal direction using the device during the engaging, and providing information regarding a subsurface feature of the earth using the analysis.

  13. Earth analysis methods, subsurface feature detection methods, earth analysis devices, and articles of manufacture

    DOEpatents

    West, Phillip B.; Novascone, Stephen R.; Wright, Jerry P.

    2011-09-27

    Earth analysis methods, subsurface feature detection methods, earth analysis devices, and articles of manufacture are described. According to one embodiment, an earth analysis method includes engaging a device with the earth, analyzing the earth in a single substantially lineal direction using the device during the engaging, and providing information regarding a subsurface feature of the earth using the analysis.

  14. ON THE VIGOR OF MANTLE CONVECTION IN SUPER-EARTHS

    SciTech Connect

    Miyagoshi, Takehiro; Tachinami, Chihiro; Kameyama, Masanori; Ogawa, Masaki E-mail: ctchnm.geo@gmail.com E-mail: cmaogawa@mail.ecc.u-tokyo.ac.jp

    2014-01-01

    Numerical models are presented to clarify how adiabatic compression affects thermal convection in the mantle of super-Earths tentimes the Earth's mass. The viscosity strongly depends on temperature, and the Rayleigh number is much higher than that of the Earth's mantle. The strong effect of adiabatic compression reduces the activity of mantle convection; hot plumes ascending from the bottom of the mantle lose their thermal buoyancy in the middle of the mantle owing to adiabatic decompression, and do not reach the surface. A thick lithosphere, as thick as 0.1times the depth of the mantle, develops along the surface boundary, and the efficiency of convective heat transport measured by the Nusselt number is reduced by a factor of about four compared with the Nusselt number for thermal convection of incompressible fluid. The strong effect of adiabatic decompression is likely to inhibit hot spot volcanism on the surface and is also likely to affect the thermal history of the mantle, and hence, the generation of magnetic field in super-Earths.

  15. Picture of the Week: An explosion of 3D printing technology

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    An explosion of 3D printing technology Scientists in Los Alamos National Laboratory's Chemistry and Explosive Science and Shock Physics divisions are exploring new methods for 3D printing that allow for the function of materials to be controlled by their internal structure. May 24, 2015 An explosion of 3D printing technology x View image on Flickr » Additive Manufacturing, known also as 3D printing, allows for the rapid production of parts with complex shapes that would be impossible to

  16. Printing Tiny Batteries | U.S. DOE Office of Science (SC)

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    "Printing" Tiny Batteries? Energy Frontier Research Centers (EFRCs) EFRCs Home Centers Research Science Highlights News & Events EFRC News EFRC Events DOE Announcements Publications History Contact BES Home 06.26.13 Stories of Discovery & Innovation: "Printing" Tiny Batteries? Print Text Size: A A A Subscribe FeedbackShare Page Researchers use sophisticated 3D printing techniques to create batteries the size of a grain of sand. This work, featured in the Office of

  17. EERE Success Story-Just Plain Cool, the 3D Printed Shelby Cobra |

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Department of Energy Just Plain Cool, the 3D Printed Shelby Cobra EERE Success Story-Just Plain Cool, the 3D Printed Shelby Cobra February 4, 2015 - 4:32pm Addthis Indistinguishable from conventional production vehicles on display, the 3D printed Shelby Cobra celebrated its 50th anniversary at the Detroit Auto Show in early January. Printed at the Department of Energy's Manufacturing Demonstration Facility at Oak Ridge National Laboratory, the Shelby Cobra electric vehicle replica is

  18. SciTech Connect: "earth system models"

    Office of Scientific and Technical Information (OSTI)

    earth system models" Find + Advanced Search Term Search Semantic Search Advanced Search All Fields: "earth system models" Semantic Semantic Term Title: Full Text: Bibliographic...

  19. Earth Tidal Analysis | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    of earth tide response of three deep, confined aquifers Earth Tidal Analysis At Raft River Geothermal Area (1980) Raft River Geothermal Area 1980 1980 Reservoir response to...

  20. Green Earth Fuels | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Earth Fuels Jump to: navigation, search Name: Green Earth Fuels Place: Houston, Texas Zip: 77057 Product: A producer and distributor of soy and palm based biodiesel Coordinates:...

  1. Smiling Earth Energy LLC | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Earth Energy LLC Place: Bakersfield, California Zip: 93314 Product: California based biodiesel producer and project developer. References: Smiling Earth Energy LLC1 This...

  2. Chemistry, Life, and Earth Sciences

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ADCLES Chemistry, Life, and Earth Sciences The CLES Directorate is home to world class capabilities in chemistry, bioscience, and earth and environmental sciences. Structural protein research Structural protein research A wide range of protein folding research Field Instrument Deployments and Operations (FIDO) Field Instrument Deployments and Operations (FIDO) Atmospheric science research Quantum Dots Quantum Dots Quantum dot research for energy and light Contact Us Associate Director Nan Sauer

  3. Through-the-earth radio

    DOEpatents

    Reagor, David; Vasquez-Dominguez, Jose

    2006-12-12

    A through-the-earth communication system that includes a digital signal input device; a transmitter operating at a predetermined frequency sufficiently low to effectively penetrate useful distances through-the earth; a data compression circuit that is connected to an encoding processor; an amplifier that receives encoded output from the encoding processor for amplifying the output and transmitting the data to an antenna; and a receiver with an antenna, a band pass filter, a decoding processor, and a data decompressor.

  4. Plasma Boundary Colloquium.key

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Excitement at the Plasma Boundary Rob Goldston (with help from many) Fusion Plasma Physics is as Easy as 1-2-3 3)Manage the heat outflux 2)Hold onto the heat & amplify it by fusion 1)Inject heat into plasma Inject Heat into Plasma We put 40 MW of neutral beams into TFTR. Heating was ~ classical, with some *AE's, fishbones, etc. ITER needs ~ 2x more heating. Projections pretty reliable with multiple types of heating systems planned. Mike Williams Hold onto the heat... Empirical scaling

  5. Printing a Car: A Team Effort in Innovation

    ScienceCinema

    Rogers, Jay; Love, Lonnie; Johnson, Mark; Ivester, Rob; Neff, Rick; Blue, Craig

    2016-07-12

    The story behind the realization of a unique project: the building of a 3D printed electric car, as told by team members. Strati materialized out of 15% carbon-reinforced ABS thermoplastic in a record 44 hours, under the very eyes of attendees at this year's International Manufacturing Technology Show (IMTS).

  6. Gas microstrip detectors based on flexible printed circuit technology

    SciTech Connect

    Salomon, M.; Crowe, K.; Faszer, W.; Lindsay, P.; Maier, J.M.C.

    1996-06-01

    The authors have studied the properties of a new type of Gas Microstrip Counter built using flexible printed circuit technology. They describe the manufacturing procedures, the assembly of the device, as well as its operation under a variety of conditions, gases and types of radiation. They also describe two new passivation materials, tantalum and niobium, which produce effective surfaces.

  7. Printing a Car: A Team Effort in Innovation

    SciTech Connect

    Rogers, Jay; Love, Lonnie; Johnson, Mark; Ivester, Rob; Neff, Rick; Blue, Craig

    2014-09-17

    The story behind the realization of a unique project: the building of a 3D printed electric car, as told by team members. Strati materialized out of 15% carbon-reinforced ABS thermoplastic in a record 44 hours, under the very eyes of attendees at this year's International Manufacturing Technology Show (IMTS).

  8. Monolithically integrated Helmholtz coils by 3-dimensional printing

    SciTech Connect

    Li, Longguang [Department of Electrical Engineering, University of MichiganShanghai Jiao Tong University Joint Institute, Shanghai Jiao Tong University, Shanghai 200240 (China); Abedini-Nassab, Roozbeh; Yellen, Benjamin B., E-mail: yellen@duke.edu [Department of Electrical Engineering, University of MichiganShanghai Jiao Tong University Joint Institute, Shanghai Jiao Tong University, Shanghai 200240 (China); Department of Mechanical Engineering and Materials Science, Duke University, P.O. Box 90300, Hudson Hall, Durham, North Carolina 27708 (United States)

    2014-06-23

    3D printing technology is of great interest for the monolithic fabrication of integrated systems; however, it is a challenge to introduce metallic components into 3D printed molds to enable broader device functionality. Here, we develop a technique for constructing a multi-axial Helmholtz coil by injecting a eutectic liquid metal Gallium Indium alloy (EGaIn) into helically shaped orthogonal cavities constructed in a 3D printed block. The tri-axial solenoids each carry up to 3.6?A of electrical current and produce magnetic field up to 70?G. Within the central section of the coil, the field variation is less than 1% and is in agreement with theory. The flow rates and critical pressures required to fill the 3D cavities with liquid metal also agree with theoretical predictions and provide scaling trends for filling the 3D printed parts. These monolithically integrated solenoids may find future applications in electronic cell culture platforms, atomic traps, and miniaturized chemical analysis systems based on nuclear magnetic resonance.

  9. Recycling-oriented characterization of plastic frames and printed circuit boards from mobile phones by electronic and chemical imaging

    SciTech Connect

    Palmieri, Roberta; Bonifazi, Giuseppe; Serranti, Silvia

    2014-11-15

    Highlights: • A recycling oriented characterization of end-of-life mobile phones was carried out. • Characterization was developed in a zero-waste-perspective, aiming to recover all the mobile phone materials. • Plastic frames and printed circuit boards were analyzed by electronic and chemical imaging. • Suitable milling/classification strategies were set up to define specialized-pre-concentrated-streams. • The proposed approach can improve the recovery of polymers, base/precious metals, rare earths and critical raw materials. - Abstract: This study characterizes the composition of plastic frames and printed circuit boards from end-of-life mobile phones. This knowledge may help define an optimal processing strategy for using these items as potential raw materials. Correct handling of such a waste is essential for its further “sustainable” recovery, especially to maximize the extraction of base, rare and precious metals, minimizing the environmental impact of the entire process chain. A combination of electronic and chemical imaging techniques was thus examined, applied and critically evaluated in order to optimize the processing, through the identification and the topological assessment of the materials of interest and their quantitative distribution. To reach this goal, end-of-life mobile phone derived wastes have been systematically characterized adopting both “traditional” (e.g. scanning electronic microscopy combined with microanalysis and Raman spectroscopy) and innovative (e.g. hyperspectral imaging in short wave infrared field) techniques, with reference to frames and printed circuit boards. Results showed as the combination of both the approaches (i.e. traditional and classical) could dramatically improve recycling strategies set up, as well as final products recovery.

  10. OSTI's E-print Network content tops 900,000 documents | OSTI, US Dept of

    Office of Scientific and Technical Information (OSTI)

    Energy Office of Scientific and Technical Information E-print Network content tops 900,000 documents Back to the OSTI News Listing for 2006 OSTI's E-print Network: Research Communications for Scientists and Engineers now provides access to over 900,000 documents on more than 22,000 scientific e-print Web sites. In addition, the E-print Network provides links to more than 2,900 relevant scientific societies. This Web portal, established as the PrePRINT Network in 2000, is a vast, integrated

  11. 3D Printed Tool for Building Aircraft Achieves Guinness World Records Title

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    | Department of Energy 3D Printed Tool for Building Aircraft Achieves Guinness World Records Title 3D Printed Tool for Building Aircraft Achieves Guinness World Records Title August 30, 2016 - 2:07pm Addthis Official measurement of the 3D printed trim tool co-developed by Oak Ridge National Laboratory and The Boeing Company exceeded the required minimum size to achieve the Guinness World Records title of largest solid 3D printed item. Official measurement of the 3D printed trim tool

  12. 3D Printed and Semiconductor Technology 'Mash-up' | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3D Printed and Semiconductor Technology 'Mash-up' 3D Printed and Semiconductor Technology 'Mash-up' May 7, 2015 - 4:11pm Addthis 3D Printed and Semiconductor Technology 'Mash-up' What will you get if you put a 3D-printed inverter package with wide bandgap materials, together with the 3D-printed EV version of the Shelby Cobra "plug and play" laboratory-on-wheels? You'll get innovation - innovation that will define even lighter, more powerful, and more efficient vehicles. Oak Ridge

  13. EERE Success Story-Novel 3-D Printed Inverters for Electric Vehicles Can

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Improve EV Power and Efficiency | Department of Energy Novel 3-D Printed Inverters for Electric Vehicles Can Improve EV Power and Efficiency EERE Success Story-Novel 3-D Printed Inverters for Electric Vehicles Can Improve EV Power and Efficiency April 28, 2015 - 2:02pm Addthis 3-D Printed Inverter 3-D Printed Inverter Plug-in electric vehicle technologies are on their way to being even lighter, more powerful and more efficient with the advent of power inverters created by 3-D printing and

  14. Browse by Discipline -- E-print Network Subject Pathways: Environmenta...

    Office of Scientific and Technical Information (OSTI)

    Technology (CREST)- Renewable Energy Policy Project Columbia University - Waste-to-Energy Research and Technology Council (WTERT) Columbia University, Department of Earth ...

  15. Browse by Discipline -- E-print Network Subject Pathways: Biotechnolog...

    Office of Scientific and Technical Information (OSTI)

    Y Z Xiao, Jingfeng (Jingfeng Xiao) - Complex Systems Research Center, University of New Hampshire Xie, Jiakang "Jack" (Jiakang "Jack" Xie) - Lamont-Doherty Earth Observatory,...

  16. Browse by Discipline -- E-print Network Subject Pathways: Biotechnolog...

    Office of Scientific and Technical Information (OSTI)

    ... - Department of Earth Sciences, Simon Fraser University Williford, Kenneth H. (Kenneth H. Williford) - Department of Geology and Geophysics, University of Wisconsin at ...

  17. Browse by Discipline -- E-print Network Subject Pathways: Energy...

    Office of Scientific and Technical Information (OSTI)

    Clarkson University Fegley Jr., Bruce (Bruce Fegley Jr.) - Department of Earth ... Donald F. (Donald F. Figer) - Chester F. Carlson Center for Imaging Science, Rochester ...

  18. Selective evaporation of focusing fluid in two-fluid hydrodynamic print head.

    SciTech Connect

    Keicher, David M.; Cook, Adam W.

    2014-09-01

    The work performed in this project has demonstrated the feasibility to use hydrodynamic focusing of two fluid steams to create a novel micro printing technology for electronics and other high performance applications. Initial efforts focused solely on selective evaporation of the sheath fluid from print stream provided insight in developing a unique print head geometry allowing excess sheath fluid to be separated from the print flow stream for recycling/reuse. Fluid flow models suggest that more than 81 percent of the sheath fluid can be removed without affecting the print stream. Further development and optimization is required to demonstrate this capability in operation. Print results using two-fluid hydrodynamic focusing yielded a 30 micrometers wide by 0.5 micrometers tall line that suggests that the cross-section of the printed feature from the print head was approximately 2 micrometers in diameter. Printing results also demonstrated that complete removal of the sheath fluid is not necessary for all material systems. The two-fluid printing technology could enable printing of insulated conductors and clad optical interconnects. Further development of this concept should be pursued.

  19. ARM - Measurement - Planetary boundary layer height

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    govMeasurementsPlanetary boundary layer height ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Measurement : Planetary boundary layer height Top of the planetary boundary layer; also known as depth or height of the mixing layer. Categories Atmospheric State Instruments The above measurement is considered scientifically relevant for the following instruments. Refer to the datastream (netcdf) file headers of each

  20. RACORO continental boundary layer cloud investigations. Part...

    Office of Scientific and Technical Information (OSTI)

    large-scale forcings Observation-based modeling case studies of continental boundary ... The cases developed are available to the general modeling community for studying ...

  1. Vertical Velocities in Continental Boundary Layer Stratocumulus...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Boundary Layer Stratocumulus Clouds Virendra Ghate Bruce Albrecht and Pavlos Kollias Why ... Frisch et al. (1995); Kollias and Albrecht (2000) Date Duration (Hour) LWP (gm -2 ) ...

  2. PIA - Savannah River Remediation Accreditation Boundary (SRR...

    Energy Saver

    PIA - Savannah River Nuclear Solution IBARS Srs Site Apps. Accreditation Boundary PIA - WEB Physical Security Major Application Occupational Medical Surveillance System (OMSS) PIA, ...

  3. Direct printing and reduction of graphite oxide for flexible supercapacitors

    SciTech Connect

    Jung, Hanyung; Ve Cheah, Chang; Jeong, Namjo; Lee, Junghoon

    2014-08-04

    We report direct printing and photo-thermal reduction of graphite oxide (GO) to obtain a highly porous pattern of interdigitated electrodes, leading to a supercapacitor on a flexible substrate. Key parameters optimized include the amount of GO delivered, the suitable photo-thermal energy level for effective flash reduction, and the substrate properties for appropriate adhesion after reduction. Tests with supercapacitors based on the printed-reduced GO showed performance comparable with commercial supercapacitors: the energy densities were 1.06 and 0.87 mWh/cm{sup 3} in ionic and organic electrolytes, respectively. The versatility in the architecture and choice of substrate makes this material promising for smart power applications.

  4. Coaxial connector for use with printed circuit board edge connector

    DOEpatents

    Howard, Donald R.; MacGill, Robert A.

    1989-01-01

    A coaxial cable connector for interfacing with an edge connector for a printed circuit board whereby a coaxial cable can be interconnected with a printed circuit board through the edge connector. The coaxial connector includes a body having two leg portions extending from one side for receiving the edge connector therebetween, and a tubular portion extending from an opposing side for receiving a coaxial cable. A cavity within the body receives a lug of the edge connector and the center conductor of the coaxial cable. Adjacent lugs of the edge connector can be bend around the edge connector housing to function as spring-loaded contacts for receiving the coaxial connector. The lugs also function to facilitate shielding of the center conductor where fastened to the edge connector lug.

  5. Barometric and Earth Tide Correction

    Energy Science and Technology Software Center

    2005-11-10

    BETCO corrects for barometric and earth tide effects in long-term water level records. A regression deconvolution method is used ot solve a series of linear equations to determine an impulse response function for the well pressure head. Using the response function, a pressure head correction is calculated and applied.

  6. Federal Sustainable Print Management - DOE Directives, Delegations, and

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Requirements G 436.1-1, Federal Sustainable Print Management by Jake Wooley The Guide provides acceptable approaches for implementing the IT sustainability requirements and criteria required by DOE Order 436.1, Departmental Sustainability, dated 5-2-11, and related to the sustainability requirements contained in Executive Order 13693, "Planning for Federal Sustainability in the Next Decade." Does not cancel/supersede other directives. g4361-1.pdf -- PDF Document, 450 KB Writer:

  7. Gas microstrip detectors based on flexible printed circuit

    SciTech Connect

    Salomon, M.; Crowe, K.; Faszer, W.; Lindsay, P.; Curran Maier, J.M.

    1995-09-01

    Microstrip Gas Detectors (MSGC`s) were introduced some years ago as position sensitive detectors capable of operating at very high rates. The authors have studied the properties of a new type of Gas Microstrip Counter built using flexible printed circuit technology. They describe the manufacturing procedures, the assembly of the device, as well as its operation under a variety of conditions, gases and types of radiation. They also describe two new passivation materials, tantalum and niobium, which produce effective surfaces.

  8. Transforming Wind Turbine Blade Mold Manufacturing with 3D Printing

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    (ORNL) Big Area Additive Manufacturing (BAAM) system. BAAM is 500 to 1,000 times faster and capable of printing polymer components over 10 times larger than today's industrial additive machines. With research blades measuring 13 meters (42 feet) in length, BAAM provides the necessary scale and foundation for this ground-breaking advancement in blade research and manufacturing. The U.S. Department of Energy's (DOE's) Office of Energy Efficiency and Renewable Energy (EERE) plays a strategic role

  9. Minutes from the February 23, 2012 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Minutes Printing and Mail Managers Exchange Forum Teleconference February 23, 2012 Participants: Headquarters (5) National Energy Technology Laboratory, PA National Security Complex Y-12 (2) Oak Ridge National Laboratory Y-12 Site Office (2) Hanford Site Office Oak Ridge Association University Oak Ridge Operations Office BWXT Pantex Site Office JanTec Corporation, Richland, Washington Los Alamos National Laboratory Chicago Office Bettis Atomic Power Laboratory National Security Technology C1,

  10. Minutes from the May 3, 2012 Printing and Mail Teleconference

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3, 2012 Printing and Mail Managers Exchange Forum Teleconference Al Majors opened the meeting by introducing Derrick Milner, Program Manager from the General Services Administration, Office of Governmentwide Policy. Mr. Milner discussed changes and updates to the Annual Mail Management Report, and new requirements as set by GSA. Changes to the FY- 2012 Mail Management Report and use of the SMART Tool System. The Annual Mail Management Reports are required at GSA by Oct 31 annually; DOE field

  11. Printing and papermaking: Energy consumption and conservation. (Latest citations from the Paper and Board, Printing, and Packaging Industries Research Associations database). Published Search

    SciTech Connect

    Not Available

    1993-06-01

    The bibliography contains citations concerning energy consumption and energy efficient design innovations for papermaking and printing equipment and operations. Economic analysis of energy utilization, computer controlled operations, energy efficient driers for papermaking and printing processes, ventilation systems, and heat recovery technology are included. (Contains a minimum of 181 citations and includes a subject term index and title list.)

  12. Environmental boundaries to energy development

    SciTech Connect

    Trivelpiece, A.W.

    1989-01-01

    Public concern about the environment, health and safety consequences of energy technology has been growing steadily for more than two decades in the United States. This concern forms an important boundary condition as the United States seeks to develop a new National Energy Strategy. Furthermore, the international aspects of the energy/environment interface such as acid rain global climate change and stratospheric ozone depletion are very prominent in US thinking. In fact, the energy systems of the world are becoming more closely coupled environmentally and otherwise. Now where is this coupling more important than that between the industrialized and developing world; the choices made by each will have profound effects on the other. The development of energy technologies compatible with both economic growth and improving and sustaining environmental quality represents a major R D challenge to the US and USSR. Decision about adoption of new technology and R D priorities can be improved by better measurements of how energy sources and uses are changing throughout the world and better methods to project the potential consequences of these decisions. Such projection require understanding relative risks of alternating existing and evolving technologies. All of these R D areas, technology improvement energy system monitoring and projection and comparative risk assessment are the topics of this seminar. Progress in each may be enhanced by collaboration and cooperation between our two countries. 7 refs., 27 figs., 5 tabs.

  13. MO-A-9A-01: Innovation in Medical Physics Practice: 3D Printing Applications

    SciTech Connect

    Ehler, E; Perks, J; Rasmussen, K; Bakic, P

    2014-06-15

    3D printing, also called additive manufacturing, has great potential to advance the field of medicine. Many medical uses have been exhibited from facial reconstruction to the repair of pulmonary obstructions. The strength of 3D printing is to quickly convert a 3D computer model into a physical object. Medical use of 3D models is already ubiquitous with technologies such as computed tomography and magnetic resonance imaging. Thus tailoring 3D printing technology to medical functions has the potential to impact patient care. This session will discuss applications to the field of Medical Physics. Topics discussed will include introduction to 3D printing methods as well as examples of real-world uses of 3D printing spanning clinical and research practice in diagnostic imaging and radiation therapy. The session will also compare 3D printing to other manufacturing processes and discuss a variety of uses of 3D printing technology outside the field of Medical Physics. Learning Objectives: Understand the technologies available for 3D Printing Understand methods to generate 3D models Identify the benefits and drawbacks to rapid prototyping / 3D Printing Understand the potential issues related to clinical use of 3D Printing.

  14. Cyclone separator having boundary layer turbulence control

    DOEpatents

    Krishna, Coimbatore R.; Milau, Julius S.

    1985-01-01

    A cyclone separator including boundary layer turbulence control that is operable to prevent undue build-up of particulate material at selected critical areas on the separator walls, by selectively varying the fluid pressure at those areas to maintain the momentum of the vortex, thereby preventing particulate material from inducing turbulence in the boundary layer of the vortical fluid flow through the separator.

  15. Boundary conditions for the subdiffusion equation

    SciTech Connect

    Shkilev, V. P.

    2013-04-15

    The boundary conditions for the subdiffusion equations are formulated using the continuous-time random walk model, as well as several versions of the random walk model on an irregular lattice. It is shown that the boundary conditions for the same equation in different models have different forms, and this difference considerably affects the solutions of this equation.

  16. Climate change stored below the earth`s surface

    SciTech Connect

    Cermak, V.; Safanda, J.; Kresl, M.

    1997-12-31

    Earth`s subsurface has a certain capability to remember what has happened on its surface tens to hundreds (or even thousands) years ago. Long-term climate changes accompanied by variations in tile mean annual temperature determine tile soil temperature, the time variations of which then propagate downwards with an attenuated amplitude and delayed phase. Ground surface temperature (GST) history, reflecting the past climate, can thus be evaluated by analysing its excursions left on the present-day temperature-depth T(z) distribution measured by precise temperature logging in the boreholes. Whereas the depths of several hundred metres may still keep and reveal a reliable record oil the climate of the past several centuries, tile uppermost layer of 100-150 in presents a plentiful archive of the recent global warming. Several characteristic examples of extracted climate recollections from holes all over the world will be resented and discussed.

  17. Non-Contact Printed Aluminum Metallization of Si Photovoltaic Devices: Preprint

    SciTech Connect

    Platt, H. A. S.; van Hest, M. F. A. M.; Li, Y.; Novak, J. P.

    2012-06-01

    Alternative solution-based techniques such as aerosol jet printing offer the dual benefits of contactless pattern deposition and high material utilization. We have used aerosol jet printing to investigate non-contact printed Al metal ink as a replacement for screen printed Al back contacts on wafer Si solar cells. This particle-based ink can be prepared at high loadings of 60 weight % metal, which enables rapid deposition of 1 - 10 um thick lines. Al lines printed on Si wafers and heated between 550 and 800 degrees C form low resistance contacts suitable for current extraction. The effectiveness of these printed Al back contacts has further been demonstrated by incorporating them into a series of 21 cm2 crystalline Si solar cells that produced a champion power conversion efficiency of 13%.

  18. Earth Week 2016 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    THIS YEAR, WE'RE CELEBRATING EARTH DAY ALL WEEK LONG. It's EarthWeek on Energy.gov We're focusing on climate change, highlighting how we're helping the nation ActOnClimate. ...

  19. Modeling the Earth System, volume 3

    SciTech Connect

    Ojima, D.

    1992-01-01

    The topics covered fall under the following headings: critical gaps in the Earth system conceptual framework; development needs for simplified models; and validating Earth system models and their subcomponents.

  20. EarthCraft Virginia | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    EarthCraft Virginia Jump to: navigation, search Name: EarthCraft Virginia Place: Richmond, VA Zip: 23220 Website: www.ecvirginia.org Coordinates: 37.5464259, -77.4644607 Show...

  1. EarthRise Capital | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    EarthRise Capital Jump to: navigation, search Name: EarthRise Capital Place: New York, New York Zip: NY 10111 Sector: Efficiency Product: Venture capital fund focused on new...

  2. EarthEnergy Limited | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Cornwall, United Kingdom Product: EarthEnergy Systems specialises in ground source heat pump systems. References: EarthEnergy Limited1 This article is a stub. You can help OpenEI...

  3. Alternative Earth Resources Inc | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    840 - 1140 West Pender St. Place: Vancouver, B.C. Zip: V6E 4G1 Sector: Geothermal energy Website: www.alternative-earth.comsHo References: Alternative Earth Website1...

  4. Google Earth Tour: Water reuse at LANL

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Google Earth Tour: Water reuse at LANL Google Earth Tour: Water reuse at LANL Open full screen to view more You are running an unsupported browser, some features may not work....

  5. Production method for making rare earth compounds

    DOEpatents

    McCallum, R.W.; Ellis, T.W.; Dennis, K.W.; Hofer, R.J.; Branagan, D.J.

    1997-11-25

    A method of making a rare earth compound, such as a earth-transition metal permanent magnet compound, without the need for producing rare earth metal as a process step, comprises carbothermically reacting a rare earth oxide to form a rare earth carbide and heating the rare earth carbide, a compound-forming reactant (e.g., a transition metal and optional boron), and a carbide-forming element (e.g., a refractory metal) that forms a carbide that is more thermodynamically favorable than the rare earth carbide whereby the rare earth compound (e.g., Nd{sub 2}Fe{sub 14}B or LaNi{sub 5}) and a carbide of the carbide-forming element are formed.

  6. Production method for making rare earth compounds

    DOEpatents

    McCallum, R. William; Ellis, Timothy W.; Dennis, Kevin W.; Hofer, Robert J.; Branagan, Daniel J.

    1997-11-25

    A method of making a rare earth compound, such as a earth-transition metal permanent magnet compound, without the need for producing rare earth metal as a process step, comprises carbothermically reacting a rare earth oxide to form a rare earth carbide and heating the rare earth carbide, a compound-forming reactant (e.g. a transition metal and optional boron), and a carbide-forming element (e.g. a refractory metal) that forms a carbide that is more thermodynamically favorable than the rare earth carbide whereby the rare earth compound (e.g. Nd.sub.2 Fe.sub.14 B or LaNi.sub.5) and a carbide of the carbide-forming element are formed.

  7. Earth

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Sustainable Building, achieving major federal sustainability goals by incorporating green improvements and practices. Energy usage in this building alone dropped by 20 percent

  8. Earth

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earned Value Management Earned Value Management Earned Value Management The mission of the DOE Earned Value Management website is to educate and train on theory and practice of Earned Value Management, and use it as an integrated Project Management process. Earned Value Management (EVM) is a systematic approach to the integration and measurement of cost, schedule, and technical (scope) accomplishments on a project or task. It provides both the government and contractors the ability to examine

  9. Argonne's 2012 Earth Day Event

    SciTech Connect

    2012-01-01

    Argonne's 2012 Earth Day event drew crowds from across the laboratory. Argonne and U.S. Department of Energy employees toured booths and interactive displays set up by Argonne programs and clubs. Several of Argonne's partners participated, including U.S. Department of Energy, University of Chicago, Abri Credit Union, DuPage County Forest Preserve, DuPage Water Commission, PACE and Morton Arboretum. Argonne scientists and engineers also participated in a poster session, discussing their clean energy research.

  10. Argonne's 2012 Earth Day Event

    ScienceCinema

    None

    2016-07-12

    Argonne's 2012 Earth Day event drew crowds from across the laboratory. Argonne and U.S. Department of Energy employees toured booths and interactive displays set up by Argonne programs and clubs. Several of Argonne's partners participated, including U.S. Department of Energy, University of Chicago, Abri Credit Union, DuPage County Forest Preserve, DuPage Water Commission, PACE and Morton Arboretum. Argonne scientists and engineers also participated in a poster session, discussing their clean energy research.

  11. Wood panel earth shelter construction

    SciTech Connect

    Berg, J.R.; Loveless, J.G.; Senkow, W.

    1986-05-27

    An earth sheltered building is described including an arch structure, the structure including footings, a floor extending between the footings and arch means extending between the footings and having a base having lower ends on the footings for defining an enclosure which is covered with earth and open at opposite ends. The arch structure consists of: joined, curved wooden panel sections arranged in tandem in adjacent rows with more than two panel sections in a row, each of the sections including circumferentially extending wooden side members; wooden sheathing sections overlying the top skins of panel sections, the sheathing including a plurality of plywood sheets lapped over the joints between the panel sections and treated with a preservative; an adhesive joining the panel sections together within each row and to adjacent rows; waterproofing means on the sheathing for waterproofing the exterior surface of the arch means; connecting means engaging the base of the arch means at the footings and within the floor for tying the base together at its lower ends; and end walls and fastener means for joining the end walls to lateral edges of the arch means, the end walls dimensioned to extend above the arch means to retain earth placed on the arch means.

  12. Energy Department Unveils 3D-Printed Building; New Initiatives During

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Industry Day | Department of Energy Unveils 3D-Printed Building; New Initiatives During Industry Day Energy Department Unveils 3D-Printed Building; New Initiatives During Industry Day October 1, 2015 - 12:25pm Addthis The Energy Department announced several new and exciting innovations and programs during Industry Day held at Oak Ridge National Laboratory (ORNL) in Tennessee Sept. 23-24. This included unveiling a 3-D printed building with integrated energy storage via bidirectional wireless

  13. Researchers find 3-D printed parts to provide low-cost, custom alternatives

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    for laboratory equipment | Princeton Plasma Physics Lab Researchers find 3-D printed parts to provide low-cost, custom alternatives for laboratory equipment By Raphael Rosen February 26, 2015 Tweet Widget Google Plus One Share on Facebook 3-D printed parts provide the stands for the aluminum globes in PPPL's Planeterrella, a device that simulates Northern Lights. (Photo by Elle Starkman/PPPL Office of Communications) 3-D printed parts provide the stands for the aluminum globes in PPPL's

  14. Researchers find 3-D printed parts to provide low-cost, custom alternatives

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    for laboratory equipment | Princeton Plasma Physics Lab Researchers find 3-D printed parts to provide low-cost, custom alternatives for laboratory equipment By Raphael Rosen February 26, 2015 Tweet Widget Google Plus One Share on Facebook 3-D printed parts provide the stands for the aluminum globes in PPPL's Planeterrella, a device that simulates Northern Lights. (Photo by Elle Starkman/PPPL Office of Communications) 3-D printed parts provide the stands for the aluminum globes in PPPL's

  15. Next Generation Lunch: Revealing the World's First 3D Printed Car (text

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    version) | Department of Energy Next Generation Lunch: Revealing the World's First 3D Printed Car (text version) Next Generation Lunch: Revealing the World's First 3D Printed Car (text version) Below is the text version for the Next Generation Lunch: Revealing the World's First 3D Printed Car Video. FILE NAME: AEMC_09172014_luncheonaddress_nextgeneration SPEAKER: Ladies and gentleman, welcome and good afternoon. Please give a warm welcome to Dr. Mark Johnson, U.S. Department of Energy.

  16. 3D-Printed Foam Outperforms Standard Materials | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    3D-Printed Foam Outperforms Standard Materials 3D-Printed Foam Outperforms Standard Materials April 27, 2016 - 5:58pm Addthis News release from Lawrence Livermore Laboratory, April 27, 2016. Lawrence Livermore National Laboratory (LLNL) material scientists have found that 3D-printed foam works better than standard cellular materials in terms of durability and long-term mechanical performance. Foams, also known as cellular solids, are an important class of materials with applications ranging from

  17. SU-E-T-455: Characterization of 3D Printed Materials for Proton Beam Therapy

    SciTech Connect

    Zou, W; Siderits, R; McKenna, M; Khan, A; Yue, N [Rutgers University, New Brunswick, NJ (United States); McDonough, J; Yin, L; Teo, B [University of Pennsylvania, Philadelphia, PA (United States); Fisher, T [Memorial Medical Center, Modesto, CA (United States)

    2014-06-01

    Purpose: The widespread availability of low cost 3D printing technologies provides an alternative fabrication method for customized proton range modifying accessories such as compensators and boluses. However the material properties of the printed object are dependent on the printing technology used. In order to facilitate the application of 3D printing in proton therapy, this study investigated the stopping power of several printed materials using both proton pencil beam measurements and Monte Carlo simulations. Methods: Five 34 cm cubes fabricated using three 3D printing technologies (selective laser sintering, fused-deposition modeling and stereolithography) from five printers were investigated. The cubes were scanned on a CT scanner and the depth dose curves for a mono-energetic pencil beam passing through the material were measured using a large parallel plate ion chamber in a water tank. Each cube was measured from two directions (perpendicular and parallel to printing plane) to evaluate the effects of the anisotropic material layout. The results were compared with GEANT4 Monte Carlo simulation using the manufacturer specified material density and chemical composition data. Results: Compared with water, the differences from the range pull back by the printed blocks varied and corresponded well with the material CT Hounsfield unit. The measurement results were in agreement with Monte Carlo simulation. However, depending on the technology, inhomogeneity existed in the printed cubes evidenced from CT images. The effect of such inhomogeneity on the proton beam is to be investigated. Conclusion: Printed blocks by three different 3D printing technologies were characterized for proton beam with measurements and Monte Carlo simulation. The effects of the printing technologies in proton range and stopping power were studied. The derived results can be applied when specific devices are used in proton radiotherapy.

  18. E-print Network provides access to science, scientists | OSTI, US Dept of

    Office of Scientific and Technical Information (OSTI)

    Energy Office of Scientific and Technical Information E-print Network provides access to science, scientists Back to the OSTI News Listing for 2006 You can search more than 900,000 scientific documents at OSTI's E-print Network. This vast, integrated network of scientific and technical information contains e-prints in basic and applied sciences, primarily in physics but also including subject areas such as chemistry, biology and life sciences, materials science, nuclear sciences and

  19. Browse by Discipline -- E-print Network Subject Pathways: Renewable...

    Office of Scientific and Technical Information (OSTI)

    Z Zhou, Quanlin (Quanlin Zhou) - Earth Sciences Division, Lawrence Berkeley National Laboratory Go back to Individual Researchers Collections: A B C D E F G H I J K L M N O P Q R ...

  20. Browse by Discipline -- E-print Network Subject Pathways: Environmenta...

    Office of Scientific and Technical Information (OSTI)

    F G H I J K L M N O P Q R S T U V W X Y Z Ford, Andrew (Andrew Ford) - School of Earth and Environmental Sciences, Washington State University Fowlie, Meredith (Meredith Fowlie) - ...

  1. A toolkit for building earth system models

    SciTech Connect

    Foster, I.

    1993-03-01

    An earth system model is a computer code designed to simulate the interrelated processes that determine the earth`s weather and climate, such as atmospheric circulation, atmospheric physics, atmospheric chemistry, oceanic circulation, and biosphere. I propose a toolkit that would support a modular, or object-oriented, approach to the implementation of such models.

  2. Secretary Moniz Tours the 3D-Printed Shelby Cobra | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Secretary Moniz Tours the 3D-Printed Shelby Cobra Secretary Moniz Tours the 3D-Printed Shelby Cobra April 23, 2015 - 1:45pm Addthis This Shelby was printed at the Department of Energy’s Manufacturing Demonstration Facility at Oak Ridge National Laboratory (ORNL) using the BAAM (Big Area Additive Manufacturing) machine and is intended as a “plug-n-play” laboratory on wheels where sustainable components can be tested and enhanced in real time. This Shelby was printed at the

  3. ORNL Unveils 3D-Printed Home and Vehicle with the Unique Ability...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    efforts of the the lab's Additive Manufacturing Integrated Energy (AMIE) demonstration. ... by natural gas, were both printed using additive manufacturing via a large-scale 3D ...

  4. V-148: Novell iPrint Client Unspecified Buffer Overflow Vulnerability

    Energy.gov [DOE]

    A vulnerability has been reported in Novell iPrint Client, which can be exploited by malicious people to compromise a user's system

  5. Secretary Moniz Tours the 3D-Printed Shelby Cobra | Department...

    Energy Saver

    in Knoxville, Tennessee, developed a finishing process that bonds the clear coat and paint layers to the printed car parts' resulting in the highest quality finish possible in...

  6. EERE Success Story-3D Printing Enables New Generation of Heat Exchangers

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    | Department of Energy 3D Printing Enables New Generation of Heat Exchangers EERE Success Story-3D Printing Enables New Generation of Heat Exchangers March 17, 2016 - 10:32am Addthis The University of Maryland used direct metal printing—a 3D printing technology—to manufacture a unique miniaturized air-to-refrigerant heat exchanger as a single, continuous piece. Image: University of Maryland, Center for Environmental Energy Engineering. The University of Maryland used direct metal

  7. The 3D-Printed Shelby Cobra: Defining Rapid Innovation | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Energy The 3D-Printed Shelby Cobra: Defining Rapid Innovation The 3D-Printed Shelby Cobra: Defining Rapid Innovation April 24, 2015 - 9:00am Addthis The 3D-Printed Shelby Cobra: Defining Rapid Innovation img-1294_crop.jpg It's been hard to miss in the media and on its almost non-stop road tour, but AMO wanted you to know that our 3D-printed EV version of the 50th anniversary Shelby Cobra just left the Forrestal building lobby after visiting for two weeks. Secretary Moniz dropped in for a

  8. OSTIblog Articles in the e-prints Topic | OSTI, US Dept of Energy Office of

    Office of Scientific and Technical Information (OSTI)

    Scientific and Technical Information e-prints Topic Get scientific e-prints by Dennis Traylor 31 Aug, 2012 in Products and Content 4267 EPN_slide2.jpg Get scientific e-prints Read more about 4267 The E-print Network provides a vast, integrated network of electronic scientific and technical information created by scientists and research engineers active in their respective fields, all full-text searchable. Documents such as these are the means by which today's scientists and researchers

  9. Category:Earth Tidal Analysis | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Earth Tidal Analysis Jump to: navigation, search Geothermalpower.jpg Looking for the Earth Tidal Analysis page? For detailed information on Earth Tidal Analysis, click here....

  10. Eddy current gauge for monitoring displacement using printed circuit coil

    DOEpatents

    Visioli, Jr., Armando J.

    1977-01-01

    A proximity detection system for non-contact displacement and proximity measurement of static or dynamic metallic or conductive surfaces is provided wherein the measurement is obtained by monitoring the change in impedance of a flat, generally spiral-wound, printed circuit coil which is excited by a constant current, constant frequency source. The change in impedance, which is detected as a corresponding change in voltage across the coil, is related to the eddy current losses in the distant conductive material target. The arrangement provides for considerable linear displacement range with increased accuracies, stability, and sensitivity over the entire range.

  11. Polarized quantum dot emission in electrohydrodynamic jet printed photonic crystals

    SciTech Connect

    See, Gloria G.; Xu, Lu; Nuzzo, Ralph G.; Sutanto, Erick; Alleyne, Andrew G.; Cunningham, Brian T.

    2015-08-03

    Tailored optical output, such as color purity and efficient optical intensity, are critical considerations for displays, particularly in mobile applications. To this end, we demonstrate a replica molded photonic crystal structure with embedded quantum dots. Electrohydrodynamic jet printing is used to control the position of the quantum dots within the device structure. This results in significantly less waste of the quantum dot material than application through drop-casting or spin coating. In addition, the targeted placement of the quantum dots minimizes any emission outside of the resonant enhancement field, which enables an 8× output enhancement and highly polarized emission from the photonic crystal structure.

  12. System and method for 3D printing of aerogels

    DOEpatents

    Worsley, Marcus A.; Duoss, Eric; Kuntz, Joshua; Spadaccini, Christopher; Zhu, Cheng

    2016-03-08

    A method of forming an aerogel. The method may involve providing a graphene oxide powder and mixing the graphene oxide powder with a solution to form an ink. A 3D printing technique may be used to write the ink into a catalytic solution that is contained in a fluid containment member to form a wet part. The wet part may then be cured in a sealed container for a predetermined period of time at a predetermined temperature. The cured wet part may then be dried to form a finished aerogel part.

  13. Property:Building/Boundaries | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    "BuildingBoundaries" Showing 25 pages using this property. (previous 25) (next 25) S Sweden Building 05K0001 + Several buildings + Sweden Building 05K0002 + Part of a building +...

  14. ARM - Field Campaign - Boundary Layer Cloud IOP

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    govCampaignsBoundary Layer Cloud IOP Campaign Links Campaign Images ARM Data Discovery Browse Data Comments? We would love to hear from you Send us a note below or call us at ...

  15. Boundary Entropy Can Increase Under Bulk RG Flow (Journal Article...

    Office of Scientific and Technical Information (OSTI)

    Boundary Entropy Can Increase Under Bulk RG Flow Citation Details In-Document Search Title: Boundary Entropy Can Increase Under Bulk RG Flow The boundary entropy log(g) of a critical ...

  16. Earth boring machine and method

    SciTech Connect

    Sullinger, R.

    1983-09-13

    An earth boring machine and method are disclosed. An above-ground reference line, such as a laser beam, is established for a hole to be bored. The direction of the reference line is detected. The direction of a cutting head of the boring machine in a bore hole is detected and signals of the detected direction are transmitted to a control unit for comparison with the reference line direction. The boring machine is controlled with, for example, cam actuated adjustable peripheral cutters on the cutting head so that the direction of the boring machine can be adjusted to that of the reference line.

  17. Science at the interface : grain boundaries in nanocrystalline...

    Office of Scientific and Technical Information (OSTI)

    Science at the interface : grain boundaries in nanocrystalline metals. Citation Details In-Document Search Title: Science at the interface : grain boundaries in nanocrystalline ...

  18. Techno-Economic Boundary Analysis of Biological Pathways to Hydrogen...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Techno-Economic Boundary Analysis of Biological Pathways to Hydrogen Production (2009) Techno-Economic Boundary Analysis of Biological Pathways to Hydrogen Production (2009) ...

  19. ARM - Field Campaign - Lower Atmospheric Boundary Layer Experiment

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Related Campaigns 2013 Lower Atmospheric Boundary Layer Experiment 2013.05.28, Turner, SGP ... Lead Scientist : David Turner For data sets, see below. Abstract Boundary layer turbulence ...

  20. Small and Powerful: Pushing the Boundaries of Nano-Magnets |...

    Office of Science (SC)

    and Powerful: Pushing the Boundaries of Nano-Magnets Basic Energy Sciences (BES) BES ... Small and Powerful: Pushing the Boundaries of Nano-Magnets Newly discovered particles ...

  1. EA-1973: Kootenai River Restoration at Bonners Ferry, Boundary...

    Energy Saver

    73: Kootenai River Restoration at Bonners Ferry, Boundary County, Idaho EA-1973: Kootenai River Restoration at Bonners Ferry, Boundary County, Idaho Summary Bonneville Power...

  2. Suppression of Grain Boundaries in Graphene Growth on Superstructured...

    Office of Scientific and Technical Information (OSTI)

    Suppression of Grain Boundaries in Graphene Growth on Superstructured Mn-Cu(111) Surface Title: Suppression of Grain Boundaries in Graphene Growth on Superstructured Mn-Cu(111) ...

  3. Technoeconomic Boundary Analysis of Biological Pathways to Hydrogen...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Technoeconomic Boundary Analysis of Biological Pathways to Hydrogen Production Technoeconomic Boundary Analysis of Biological Pathways to Hydrogen Production Report documenting the ...

  4. A dual mass flux framework for boundary layer convection

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    A dual mass flux framework for boundary layer convection Neggers, Roel European Centre for Medium-range Weather Forecasts (ECMWF) Category: Modeling A new convective boundary layer...

  5. Iterative solution of Hermite boundary integral equations (Journal...

    Office of Scientific and Technical Information (OSTI)

    Iterative solution of Hermite boundary integral equations Citation Details In-Document Search Title: Iterative solution of Hermite boundary integral equations An efficient ...

  6. Through-the-earth radio

    DOEpatents

    Reagor, David; Vasquez-Dominguez, Jose

    2006-05-09

    A method and apparatus for effective through-the-earth communication involves a signal input device connected to a transmitter operating at a predetermined frequency sufficiently low to effectively penetrate useful distances through-the earth, and having an analog to digital converter receiving the signal input and passing the signal input to a data compression circuit that is connected to an encoding processor, the encoding processor output being provided to a digital to analog converter. An amplifier receives the analog output from the digital to analog converter for amplifying said analog output and outputting said analog output to an antenna. A receiver having an antenna receives the analog output passes the analog signal to a band pass filter whose output is connected to an analog to digital converter that provides a digital signal to a decoding processor whose output is connected to an data decompressor, the data decompressor providing a decompressed digital signal to a digital to analog converter. An audio output device receives the analog output form the digital to analog converter for producing audible output.

  7. Development and Optimization of Viable Human Platforms through 3D Printing

    SciTech Connect

    Parker, Paul R.; Moya, Monica L.; Wheeler, Elizabeth K.

    2015-08-21

    3D printing technology offers a unique method for creating cell cultures in a manner far more conducive to accurate representation of human tissues and systems. Here we print cellular structures capable of forming vascular networks and exhibiting qualities of natural tissues and human systems. This allows for cheaper and readily available sources for further study of biological and pharmaceutical agents.

  8. Multi-Layer Inkjet Printed Contacts for Silicon Solar Cells: Preprint

    SciTech Connect

    Curtis, C. J.; van hest, M.; Miedaner, A.; Kaydanova, T.; Smith, L.; Ginley, D. S.

    2006-05-01

    Ag, Cu, and Ni metallizations were inkjet printed with near vacuum deposition quality. The approach developed can be easily extended to other conductors such as Pt, Pd, Au, etc. Thick highly conducting lines of Ag and Cu demonstrating good adhesion to glass, Si, and printed circuit board (PCB) have been printed at 100-200 C in air and N2 respectively. Ag grids were inkjet-printed on Si solar cells and fired through the silicon nitride AR layer at 850 C, resulting in 8% cells. Next generation inks, including an ink that etches silicon nitride, have now been developed. Multi-layer inkjet printing of the etching ink followed by Ag ink produced contacts under milder conditions and gave solar cells with efficiencies as high as 12%.

  9. An RFC 1179 Compatible Remote Print Server for Windows 3.1

    Energy Science and Technology Software Center

    1993-11-09

    Internet RFC 1179 describes the protocol to be used for printing files on a remote printer in a TCP/IP network. The protocol is client/server, meaning that the client initiates the print request, and the server receives the request and performs the actual printing locally. This protocol has been in long use on Unix systems derived from the Berkeley Software Distribution, such as DEC''s Ultrix and Sun''s SunOS. LPD Services implements the server portion of thismore » protocol. It handles both the network communication and conformance with the protocol, and printing using the Microsoft Windows device independent printing interface.« less

  10. Pioneering Inkjet Printing Technology Produces Thin-Film Photovoltaics; The Spectrum of Clean Energy Innovation (Fact Sheet)

    SciTech Connect

    Not Available

    2010-06-01

    Fact sheet describing NREL's development of inkjet printing technology that can be used to produce thin-film solar modules.

  11. 3D%20printed%20perforated%20metal%20box.jpg | OSTI, US Dept of Energy

    Office of Scientific and Technical Information (OSTI)

    Office of Scientific and Technical Information 3D%20printed%20perforated%20metal%20box

  12. Amphoteric doping of praseodymium Pr3+ in SrTiO3 grain boundaries

    DOE PAGES [OSTI]

    Yang, H.; Lee, H. S.; Kotula, P. G.; Sato, Y.; Ikuhara, Y.; Browning, N. D.

    2015-03-26

    Charge Compensation in rare-earth Praseodymium (Pr3+) doped SrTiO3 plays an important role in determining the overall photoluminescence properties of the system. Here, the Pr3+ doping behavior in SrTiO3 grain boundaries (GBs) is analyzed using aberration corrected scanning transmission electron microscopy (STEM). The presence of Pr3+ induces structure variations and changes the statistical prevalence of GB structures. In contrast to the assumption that Pr3+ substitutes for A site as expected in the bulk, Pr3+ is found to substitute both Sr and Ti sites inside GBs with the highest concentration in the Ti sites. As a result, this amphoteric doping behavior inmore » the boundary plane is further confirmed by first principles theoretical calculations.« less

  13. Amphoteric doping of praseodymium Pr3+ in SrTiO3 grain boundaries

    DOE PAGES [OSTI]

    Yang, H.; Lee, H. S.; Kotula, P. G.; Sato, Y.; Ikuhara, Y.; Browning, N. D.

    2015-03-26

    Charge Compensation in rare-earth Praseodymium (Pr3+) doped SrTiO3 plays an important role in determining the overall photoluminescence properties of the system. Here, the Pr3+ doping behavior in SrTiO3 grain boundaries (GBs) is analyzed using aberration corrected scanning transmission electron microscopy (STEM). The presence of Pr3+ induces structure variations and changes the statistical prevalence of GB structures. In contrast to the assumption that Pr3+ substitutes for A site as expected in the bulk, Pr3+ is found to substitute both Sr and Ti sites inside GBs with the highest concentration in the Ti sites. As a result, this amphoteric doping behavior inmore »the boundary plane is further confirmed by first principles theoretical calculations.« less

  14. Boundary Layer Cloudiness Parameterizations Using ARM Observations

    SciTech Connect

    Bruce Albrecht

    2004-09-15

    This study used DOE ARM data and facilities to: (1) study macroscopic properties of continental stratus clouds at SGP and the factors controlling these properties, (2) develop a scientific basis for understanding the processes responsible for the formation of boundary layer clouds using ARM observations in conjunction with simple parametric models and LES, and (3) evaluate cumulus cloud characteristics retrieved from the MMCR operating at TWP-Nauru. In addition we have used high resolution 94 GHz observations of boundary layer clouds and precipitation to: (1) develop techniques for using high temporal resolution Doppler velocities to study large-eddy circulations and turbulence in boundary layer clouds and estimate the limitations of using current and past MMCR data for boundary layer cloud studies, (2) evaluate the capability and limitations of the current MMCR data for estimating reflectivity, vertical velocities, and spectral under low- signal-to-noise conditions associated with weak no n-precipitating clouds, (3) develop possible sampling modes for the new MMCR processors to allow for adequate sampling of boundary layer clouds, and (4) retrieve updraft and downdraft structures under precipitating conditions.

  15. Earth Systems Science and Engineering

    SciTech Connect

    Rotman, D A

    2006-02-21

    Providing the essential energy and water systems to support human needs while understanding and addressing their environmental consequences is a watershed problem for the 21st century. The LLNL Earth System Science and Engineering Program seeks to provide the scientific understanding and technological expertise to help provide solutions at both global and regional scales. Our work is highly collaborative with universities, laboratories and industrial partners across the world and involves observational data, laboratory experiments, and numerical simulations. The energy systems we have enjoyed for the last 100 years have resulted in the advanced standard of living in the developed world and a major emerging problem with climate change. Now we face a simultaneous realization that our reliance on fossil fuels is a source of conflict and economic disruption as well as causing potentially abrupt, even catastrophic global climate change. The climate and energy problem is perhaps the greatest challenge ever faced by mankind. Fossil fuel remains the least expensive and most available source of energy and the basis of our economy. The use of fossil fuels, especially over the last 100 years has led to a 30% increase in CO{sub 2} in the atmosphere. The problem is growing. The population of the Earth will increase by several billion people in the next 50 years. If economic growth is to continue, the demand for energy is estimated to approximately double in the next 50 years so that we will need approximately 10 TW more energy than the 15 TW we use now. Much of this demand will come from the developing world where most of the population growth will occur and where advanced energy technology is not generally used. The problem affects and is affected by a complex system of systems. The climate and energy problem will affect resources, social structure and the probability of increased conflict. No one person, no one nation, no one technology can solve the problem. There is no

  16. Space technology can help sustain Earth

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Space technology can help sustain Earth Space technology can help sustain Earth Satellite imagery and communication are powerful aids in confronting humanitarian and environmental issues June 12, 2016 Mars The 2014 Sabina Wildfire in California, captured by low-cost satellites created by Planet Labs Credit: Image by Planet Labs Inc via Wikimedia Commons under Creative Commons license Space technology can help sustain Earth ... Planet Labs, a San Francisco-based space startup, was born in the

  17. Local Students Celebrate Earth Day at NREL

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Students Celebrate Earth Day at NREL For more information contact: e:mail: Public Affairs Golden, Colo., April 17, 1998 — Media are invited to cover Earth Day celebration designed to inspire a new generation of scientists to discover better ways of using our natural resources. What: The U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) will host an Earth Day celebration for 60 elementary students. Hands-on activities will include building model solar cars and

  18. Educate yourself about stewardship this Earth Day

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Educate yourself about stewardship this Earth Day Educate yourself about stewardship this Earth Day WHEN: Apr 20, 2016 12:00 PM - 2:00 PM WHERE: Bradbury Science Museum 1350 Central Ave, Los Alamos, NM 87544, USA CONTACT: Linda Anderman (505) 665-9196 CATEGORY: Bradbury INTERNAL: Calendar Login Event Description Earth Day open house Open House at the Bradbury Science Museum hosted by the Lab's Environmental Protection & Compliance-Environmental Stewardship resources team. Laboratory

  19. Surface and grain boundary scattering in nanometric Cu thin films: A quantitative analysis including twin boundaries

    SciTech Connect

    Barmak, Katayun [Department of Applied Physics and Applied Mathematics, Columbia University, New York, New York 10027 and Department of Materials Science and Engineering and Materials Research Science and Engineering Center, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, Pennsylvania 15213 (United States); Darbal, Amith [Department of Materials Science and Engineering and Materials Research Science and Engineering Center, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, Pennsylvania 15213 (United States); Ganesh, Kameswaran J.; Ferreira, Paulo J. [Materials Science and Engineering, The University of Texas at Austin, 1 University Station, Austin, Texas 78712 (United States); Rickman, Jeffrey M. [Department of Materials Science and Engineering and Department of Physics, Lehigh University, Bethlehem, Pennsylvania 18015 (United States); Sun, Tik; Yao, Bo; Warren, Andrew P.; Coffey, Kevin R., E-mail: kb2612@columbia.edu [Department of Materials Science and Engineering, University of Central Florida, 4000 Central Florida Boulevard, Orlando, Florida 32816 (United States)

    2014-11-01

    The relative contributions of various defects to the measured resistivity in nanocrystalline Cu were investigated, including a quantitative account of twin-boundary scattering. It has been difficult to quantitatively assess the impact twin boundary scattering has on the classical size effect of electrical resistivity, due to limitations in characterizing twin boundaries in nanocrystalline Cu. In this study, crystal orientation maps of nanocrystalline Cu films were obtained via precession-assisted electron diffraction in the transmission electron microscope. These orientation images were used to characterize grain boundaries and to measure the average grain size of a microstructure, with and without considering twin boundaries. The results of these studies indicate that the contribution from grain-boundary scattering is the dominant factor (as compared to surface scattering) leading to enhanced resistivity. The resistivity data can be well-described by the combined FuchsSondheimer surface scattering model and MayadasShatzkes grain-boundary scattering model using Matthiessen's rule with a surface specularity coefficient of p?=?0.48 and a grain-boundary reflection coefficient of R?=?0.26.

  20. LANL | Solid Earth Geophysics | EES-17

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    to monitor underground explosions, maintain our ability to conduct tests, and develop the Yucca Mountain Project. In addition, we study the nonlinear properties of earth materials,...

  1. Improved method for preparing rare earth sesquichalcogenides

    DOEpatents

    Takeshita, T.; Beaudry, B.J.; Gschneidner, K.A. Jr.

    1982-04-14

    An improved method for the preparation of high purity rare earth sesquichalcogenides is described. The rare earth, as one or more pieces of the metal, is sealed under a vacuum with a stoichiometric amount of sulfur or selenium and a small amount of iodine into a quartz reaction vessel. The sealed vessel is then heated to above the vaporization temperature of the chalcogen and below the melting temperature of the rare earth metal and maintained until the product has been formed. The iodine is then vaporized off leaving a pure product. The rare earth sulfides and selenides thus formed are useful as semiconductors and as thermoelectric generators. 3 tables.

  2. Earth-abundant semiconductors for photovoltaic applications ...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth-abundant semiconductors for photovoltaic applications Thin film photovoltaics (solar cells) has the potential to revolutionize our energy landscape by producing clean,...

  3. Earth Power Resources Inc | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Resources Inc is a company based in Tulsa, Oklahoma. Earth Power Resources Inc in Tulsa, OK is a private company categorized under: Electric Companies. Records show it was...

  4. Earth Day Coalition | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Day Coalition Jump to: navigation, search Name: Earth Day Coalition Address: 3606 Bridge Avenue, Suite 4 Place: Cleveland, Ohio Zip: 44113 Coordinates: 41.4829135, -81.7117416...

  5. Fusion On Earth | Princeton Plasma Physics Lab

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Events Research Education Organization Contact Us News Room News Archive Fusion News ... Princeton Journal Watch Blog PPPL Experts Research at Princeton Fusion On Earth ...

  6. Earth Turbines Inc | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Earth Turbines Inc Place: Hinesburg, Vermont Zip: 5461 Sector: Wind energy Product: Start-up company developing small-scale wind technology for the residential and commercial...

  7. Clean Earth Capital LLP | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Capital LLP Jump to: navigation, search Name: Clean Earth Capital LLP Place: EDINBURGH, United Kingdom Zip: EH6 4NW Sector: Renewable Energy Product: Edinburgh-based corporate...

  8. MIT- Earth Resources Laboratory | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Name: MIT- Earth Resources Laboratory Address: 77 Massachusetts Avenue Place: Cambridge, Massachusetts Zip: 02139 Region: Greater Boston Area Website: eaps.mit.eduerl...

  9. Center for Space and Earth Science

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Deadlines, Events Partnerships NSEC CSES Center for Space and Earth Science Formerly ... Geophysics David Coblentz (505) 667-2781 Email Space Physics Geoffrey Reeves (505) ...

  10. EarthTronics Inc | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Name: EarthTronics Inc. Place: Muskegon, Michigan Zip: 49440 Product: Michigan-based firm that has licensed the Honeywell International brand for its gearless micro-scale...

  11. Earth Share Oregon | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Share Oregon Jump to: navigation, search Name: Earth Share Oregon Address: 319 SW Washington Street Place: Portland, Oregon Zip: 97204 Region: Pacific Northwest Area Website:...

  12. Leverage Earth Day to Promote Energy Efficiency

    Energy.gov [DOE]

    Learn how to leverage Earth Day and other holidays by visiting the Better Buildings Residential Program Solution Center for helpful peer exchange call summaries and case studies:

  13. Wireless boundary monitor system and method

    DOEpatents

    Haynes, H.D.; Ayers, C.W.

    1997-12-09

    A wireless boundary monitor system used to monitor the integrity of a boundary surrounding an area uses at least two housings having at least one transmitting means for emitting ultrasonic pressure waves to a medium. Each of the housings has a plurality of receiving means for sensing the pressure waves in the medium. The transmitting means and the receiving means of each housing are aimable and communicably linked. At least one of the housings is equipped with a local alarm means for emitting a first alarm indication whereby, when the pressure waves propagating from a transmitting means to a receiving means are sufficiently blocked by an object a local alarm means or a remote alarm means or a combination thereof emit respective alarm indications. The system may be reset either manually or automatically. This wireless boundary monitor system has useful applications in both indoor and outdoor environments. 4 figs.

  14. Wireless boundary monitor system and method

    DOEpatents

    Haynes, Howard D.; Ayers, Curtis W.

    1997-01-01

    A wireless boundary monitor system used to monitor the integrity of a boundary surrounding an area uses at least two housings having at least one transmitting means for emitting ultrasonic pressure waves to a medium. Each of the housings has a plurality of receiving means for sensing the pressure waves in the medium. The transmitting means and the receiving means of each housing are aimable and communicably linked. At least one of the housings is equipped with a local alarm means for emitting a first alarm indication whereby, when the pressure waves propagating from a transmitting means to a receiving means are sufficiently blocked by an object a local alarm means or a remote alarm means or a combination thereof emit respective alarm indications. The system may be reset either manually or automatically. This wireless boundary monitor system has useful applications in both indoor and outdoor environments.

  15. Browse by Discipline -- E-print Network Subject Pathways: Biology...

    Office of Scientific and Technical Information (OSTI)

    E F G H I J K L M N O P Q R S T U V W X Y Z Dashtgard, Shahin (Shahin Dashtgard) - Department of Earth Sciences, Simon Fraser University Datta-Gupta, Akhil (Akhil Datta-Gupta) - ...

  16. Bursting frequency prediction in turbulent boundary layers

    SciTech Connect

    LIOU,WILLIAM W.; FANG,YICHUNG

    2000-02-01

    The frequencies of the bursting events associated with the streamwise coherent structures of spatially developing incompressible turbulent boundary layers were predicted using global numerical solution of the Orr-Sommerfeld and the vertical vorticity equations of hydrodynamic stability problems. The structures were modeled as wavelike disturbances associated with the turbulent mean flow. The global method developed here involves the use of second and fourth order accurate finite difference formula for the differential equations as well as the boundary conditions. An automated prediction tool, BURFIT, was developed. The predicted resonance frequencies were found to agree very well with previous results using a local shooting technique and measured data.

  17. Google Earth locations of USA and seafloor hydrothermal vents with associated rare earth element data

    DOE Data Explorer

    Andrew Fowler

    2016-02-10

    Google Earth .kmz files that contain the locations of geothermal wells and thermal springs in the USA, and seafloor hydrothermal vents that have associated rare earth element data. The file does not contain the actual data, the actual data is available through the GDR website in two tier 3 data sets entitled "Compilation of Rare Earth Element Analyses from US Geothermal Fields and Mid Ocean Ridge (MOR) Hydrothermal Vents" and "Rare earth element content of thermal fluids from Surprise Valley, California"

  18. Impact of pulse thermal processing on the properties of inkjet printed metal and flexible sensors

    DOE PAGES [OSTI]

    Joshi, Pooran C.; Kuruganti, Teja; Killough, Stephen M.

    2015-03-11

    In this paper, we report on the low temperature processing of environmental sensors employing pulse thermal processing (PTP) technique to define a path toward flexible sensor technology on plastic, paper, and fabric substrates. Inkjet printing and pulse thermal processing technique were used to realize mask-less, additive integration of low-cost sensors on polymeric substrates with specific focus on temperature, humidity, and strain sensors. The printed metal line performance was evaluated in terms of the electrical conductivity characteristics as a function of post-deposition thermal processing conditions. The PTP processed Ag metal lines exhibited high conductivity with metal sheet resistance values below 100more » mΩ/{whitesquare} using a pulse width as short as 250 μs. The flexible temperature and relative humidity sensors were defined on flexible polyimide substrates by direct printing of Ag metal structures. The printed resistive temperature sensor and capacitive humidity sensor were characterized for their sensitivity with focus on future smart-building applications. Strain gauges were printed on polyimide substrate to determine the mechanical properties of the silver nanoparticle films. Finally, the observed electrical properties of the printed metal lines and the sensitivity of the flexible sensors show promise for the realization of a high performance print-on-demand technology exploiting low thermal-budget PTP technique.« less

  19. Apparatus And Method Of Using Flexible Printed Circuit Board In Optical Transceiver Device

    DOEpatents

    Anderson, Gene R.; Armendariz, Marcelino G.; Bryan, Robert P.; Carson, Richard F.; Duckett, III, Edwin B.; McCormick, Frederick B.; Peterson, David W.; Peterson, Gary D.; Reysen, Bill H.

    2005-03-15

    This invention relates to a flexible printed circuit board that is used in connection with an optical transmitter, receiver or transceiver module. In one embodiment, the flexible printed circuit board has flexible metal layers in between flexible insulating layers, and the circuit board comprises: (1) a main body region orientated in a first direction having at least one electrical or optoelectronic device; (2) a plurality of electrical contact pads integrated into the main body region, where the electrical contact pads function to connect the flexible printed circuit board to an external environment; (3) a buckle region extending from one end of the main body region; and (4) a head region extending from one end of the buckle region, and where the head region is orientated so that it is at an angle relative to the direction of the main body region. The electrical contact pads may be ball grid arrays, solder balls or land-grid arrays, and they function to connect the circuit board to an external environment. A driver or amplifier chip may be adapted to the head region of the flexible printed circuit board. In another embodiment, a heat spreader passes along a surface of the head region of the flexible printed circuit board, and a window is formed in the head region of the flexible printed circuit board. Optoelectronic devices are adapted to the head spreader in such a manner that they are accessible through the window in the flexible printed circuit board.

  20. A toolkit for building earth system models

    SciTech Connect

    Foster, I.

    1993-03-01

    An earth system model is a computer code designed to simulate the interrelated processes that determine the earth's weather and climate, such as atmospheric circulation, atmospheric physics, atmospheric chemistry, oceanic circulation, and biosphere. I propose a toolkit that would support a modular, or object-oriented, approach to the implementation of such models.

  1. Ames Lab 101: Rare-Earth Recycling

    ScienceCinema

    Ryan Ott

    2013-06-05

    Recycling keeps paper, plastics, and even jeans out of landfills. Could recycling rare-earth magnets do the same? Perhaps, if the recycling process can be improved. Scientists at the U.S. Department of Energy's Ames Laboratory are working to more effectively remove the neodymium, a rare earth, from the mix of other materials in a magnet.

  2. Ternary rare earth-lanthanide sulfides

    DOEpatents

    Takeshita, Takuo; Gschneidner JR., Karl A.; Beaudry, Bernard J.

    1987-01-06

    A new ternary rare earth sulfur compound having the formula: where M is a rare earth element selected from the group europium, samarium and ytterbium and x=0.15 to 0.8. The compound has good high-temperature thermoelectric properties and exhibits long-term structural stability up to 1000.degree. C.

  3. Equivariant preconditioners for boundary element methods

    SciTech Connect

    Tausch, J.

    1994-12-31

    In this paper the author proposes and discusses two preconditioners for boundary integral equations on domains which are nearly symmetric. The preconditioners under consideration are equivariant, that is, they commute with a group of permutation matrices. Numerical experiments demonstrate their efficiency for the GMRES method.

  4. Planetary Boundary Layer from AERI and MPL

    DOE Data Explorer

    Sawyer, Virginia

    2014-02-13

    The distribution and transport of aerosol emitted to the lower troposphere is governed by the height of the planetary boundary layer (PBL), which limits the dilution of pollutants and influences boundary-layer convection. Because radiative heating and cooling of the surface strongly affect the PBL top height, it follows diurnal and seasonal cycles and may vary by hundreds of meters over a 24-hour period. The cap the PBL imposes on low-level aerosol transport makes aerosol concentration an effective proxy for PBL height: the top of the PBL is marked by a rapid transition from polluted, well-mixed boundary-layer air to the cleaner, more stratified free troposphere. Micropulse lidar (MPL) can provide much higher temporal resolution than radiosonde and better vertical resolution than infrared spectrometer (AERI), but PBL heights from all three instruments at the ARM SGP site are compared to one another for validation. If there is agreement among them, the higher-resolution remote sensing-derived PBL heights can accurately fill in the gaps left by the low frequency of radiosonde launches, and thus improve model parameterizations and our understanding of boundary-layer processes.

  5. Thick diffusion limit boundary layer test problems

    SciTech Connect

    Bailey, T. S.; Warsa, J. S.; Chang, J. H.; Adams, M. L.

    2013-07-01

    We develop two simple test problems that quantify the behavior of computational transport solutions in the presence of boundary layers that are not resolved by the spatial grid. In particular we study the quantitative effects of 'contamination' terms that, according to previous asymptotic analyses, may have a detrimental effect on the solutions obtained by both discontinuous finite element (DFEM) and characteristic-method (CM) spatial discretizations, at least for boundary layers caused by azimuthally asymmetric incident intensities. Few numerical results have illustrated the effects of this contamination, and none have quantified it to our knowledge. Our test problems use leading-order analytic solutions that should be equal to zero in the problem interior, which means the observed interior solution is the error introduced by the contamination terms. Results from DFEM solutions demonstrate that the contamination terms can cause error propagation into the problem interior for both orthogonal and non-orthogonal grids, and that this error is much worse for non-orthogonal grids. This behavior is consistent with the predictions of previous analyses. We conclude that these boundary layer test problems and their variants are useful tools for the study of errors that are introduced by unresolved boundary layers in diffusive transport problems. (authors)

  6. Direct laser immobilization of photosynthetic material on screen printed electrodes for amperometric biosensor

    SciTech Connect

    Boutopoulos, Christos; Zergioti, Ioanna; Touloupakis, Eleftherios; Pezzotti, Ittalo; Giardi, Maria Teresa

    2011-02-28

    This letter demonstrates the direct laser printing of photosynthetic material onto low cost nonfunctionalized screen printed electrodes for the fabrication of photosynthesis-based amperometric biosensors. The high kinetic energy of the transferred material induces direct immobilization of the thylakoids onto the electrodes without the use of linkers. This type of immobilization is able to establish efficient electrochemical contact between proteins and electrode, stabilizing the photosynthetic biomolecule and transporting electrons to the solid state device with high efficiency. The functionality of the laser printed biosensors was evaluated by the detection of a common herbicide such as Linuron.

  7. EERE Success Story-ORNL Unveils 3D-Printed Home and Vehicle with the

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Unique Ability to Power One Another | Department of Energy ORNL Unveils 3D-Printed Home and Vehicle with the Unique Ability to Power One Another EERE Success Story-ORNL Unveils 3D-Printed Home and Vehicle with the Unique Ability to Power One Another November 17, 2015 - 10:42am Addthis EERE Success Story—ORNL Unveils 3D-Printed Home and Vehicle with the Unique Ability to Power One Another In September, the Department of Energy's Oak Ridge National Laboratory (ORNL) announced successful

  8. The Future of Manufacturing Takes Shape: 3D Printed Car on Display at

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Manufacturing Summit | Department of Energy The Future of Manufacturing Takes Shape: 3D Printed Car on Display at Manufacturing Summit The Future of Manufacturing Takes Shape: 3D Printed Car on Display at Manufacturing Summit September 17, 2014 - 9:50am Addthis WORLD&#039;S FIRST 1 of 6 WORLD'S FIRST The world's first 3D-printed car on display at the International Manufacturing Technology Show in Chicago last week. Arizona-based Local Motors, and Cincinnati Incorporated teamed with Oak

  9. Get science-Access E-print Network for current research documents,

    Office of Scientific and Technical Information (OSTI)

    researchers' Web sites, and scientific societies | OSTI, US Dept of Energy Office of Scientific and Technical Information science-Access E-print Network for current research documents, researchers' Web sites, and scientific societies Back to the OSTI News Listing for 2007 Gain access to more than 1 million e-print science documents, over 25,000 Web sites, and links to more than 2,900 scientific societies at OSTI's E-print Network, a fast-growing searchable scientific communications network.

  10. The 3D-Printed Shelby Cobra: Defining Rapid Innovation | Department of

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Energy The 3D-Printed Shelby Cobra: Defining Rapid Innovation The 3D-Printed Shelby Cobra: Defining Rapid Innovation "He said he’d get in if he could drive." "He said he'd get in if he could drive." It's been hard to miss in the media and on its almost non-stop road tour, but AMO wanted you to know that our 3D-printed EV version of the 50th anniversary Shelby Cobra just left the Forrestal building lobby after visiting for two weeks. Secretary Moniz dropped in for a

  11. Technical Note: Characterization of custom 3D printed multimodality imaging phantoms

    SciTech Connect

    Bieniosek, Matthew F.; Lee, Brian J.; Levin, Craig S.

    2015-10-15

    Purpose: Imaging phantoms are important tools for researchers and technicians, but they can be costly and difficult to customize. Three dimensional (3D) printing is a widely available rapid prototyping technique that enables the fabrication of objects with 3D computer generated geometries. It is ideal for quickly producing customized, low cost, multimodal, reusable imaging phantoms. This work validates the use of 3D printed phantoms by comparing CT and PET scans of a 3D printed phantom and a commercial “Micro Deluxe” phantom. This report also presents results from a customized 3D printed PET/MRI phantom, and a customized high resolution imaging phantom with sub-mm features. Methods: CT and PET scans of a 3D printed phantom and a commercial Micro Deluxe (Data Spectrum Corporation, USA) phantom with 1.2, 1.6, 2.4, 3.2, 4.0, and 4.8 mm diameter hot rods were acquired. The measured PET and CT rod sizes, activities, and attenuation coefficients were compared. A PET/MRI scan of a custom 3D printed phantom with hot and cold rods was performed, with photon attenuation and normalization measurements performed with a separate 3D printed normalization phantom. X-ray transmission scans of a customized two level high resolution 3D printed phantom with sub-mm features were also performed. Results: Results show very good agreement between commercial and 3D printed micro deluxe phantoms with less than 3% difference in CT measured rod diameter, less than 5% difference in PET measured rod diameter, and a maximum of 6.2% difference in average rod activity from a 10 min, 333 kBq/ml (9 μCi/ml) Siemens Inveon (Siemens Healthcare, Germany) PET scan. In all cases, these differences were within the measurement uncertainties of our setups. PET/MRI scans successfully identified 3D printed hot and cold rods on PET and MRI modalities. X-ray projection images of a 3D printed high resolution phantom identified features as small as 350 μm wide. Conclusions: This work shows that 3D printed

  12. Bob Ellis designs a PPPL first: A 3D printed mirror for microwave launchers

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    | Princeton Plasma Physics Lab Bob Ellis designs a PPPL first: A 3D printed mirror for microwave launchers By John Greenwald October 28, 2014 Tweet Widget Google Plus One Share on Facebook Bob Ellis with a 3D-printed plastic prototype for a non-mirror part of the launcher. (Photo by Elle Starkman/PPPL Office of Communications) Bob Ellis with a 3D-printed plastic prototype for a non-mirror part of the launcher. Gallery: Completed stainless steel and copper mirror system. (Photo by Elle

  13. Bob Ellis designs a PPPL first: A 3D printed mirror for microwave launchers

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    | Princeton Plasma Physics Lab Bob Ellis designs a PPPL first: A 3D printed mirror for microwave launchers By John Greenwald October 28, 2014 Tweet Widget Google Plus One Share on Facebook Bob Ellis with a 3D-printed plastic prototype for a non-mirror part of the launcher. (Photo by Elle Starkman/PPPL Office of Communications) Bob Ellis with a 3D-printed plastic prototype for a non-mirror part of the launcher. Gallery: Completed stainless steel and copper mirror system. (Photo by Elle

  14. Method for laser drilling subterranean earth formations

    DOEpatents

    Shuck, Lowell Z.

    1976-08-31

    Laser drilling of subterranean earth formations is efficiently accomplished by directing a collimated laser beam into a bore hole in registry with the earth formation and transversely directing the laser beam into the earth formation with a suitable reflector. In accordance with the present invention, the bore hole is highly pressurized with a gas so that as the laser beam penetrates the earth formation the high pressure gas forces the fluids resulting from the drilling operation into fissures and pores surrounding the laser-drilled bore so as to inhibit deleterious occlusion of the laser beam. Also, the laser beam may be dynamically programmed with some time dependent wave form, e.g., pulsed, to thermally shock the earth formation for forming or enlarging fluid-receiving fissures in the bore.

  15. Modeling the summertime Arctic cloudy boundary layer

    SciTech Connect

    Curry, J.A.; Pinto, J.O.; McInnes, K.L.

    1996-04-01

    Global climate models have particular difficulty in simulating the low-level clouds during the Arctic summer. Model problems are exacerbated in the polar regions by the complicated vertical structure of the Arctic boundary layer. The presence of multiple cloud layers, a humidity inversion above cloud top, and vertical fluxes in the cloud that are decoupled from the surface fluxes, identified in Curry et al. (1988), suggest that models containing sophisticated physical parameterizations would be required to accurately model this region. Accurate modeling of the vertical structure of multiple cloud layers in climate models is important for determination of the surface radiative fluxes. This study focuses on the problem of modeling the layered structure of the Arctic summertime boundary-layer clouds and in particular, the representation of the more complex boundary layer type consisting of a stable foggy surface layer surmounted by a cloud-topped mixed layer. A hierarchical modeling/diagnosis approach is used. A case study from the summertime Arctic Stratus Experiment is examined. A high-resolution, one-dimensional model of turbulence and radiation is tested against the observations and is then used in sensitivity studies to infer the optimal conditions for maintaining two separate layers in the Arctic summertime boundary layer. A three-dimensional mesoscale atmospheric model is then used to simulate the interaction of this cloud deck with the large-scale atmospheric dynamics. An assessment of the improvements needed to the parameterizations of the boundary layer, cloud microphysics, and radiation in the 3-D model is made.

  16. On the interaction of solutes with grain boundaries

    SciTech Connect

    Dingreville, Remi Philippe Michel; Berbenni, Stephane

    2015-11-01

    Solute segregation to grain boundaries is considered by modeling solute atoms as misfitting inclusions within a disclination structural unit model describing the grain boundary structure and its intrinsic stress field. The solute distribution around grain boundaries is described through Fermi–Dirac statistics of site occupancy. The susceptibility of hydrogen segregation to symmetric tilt grain boundaries is discussed in terms of the misorientation angle, the defect type characteristics at the grain boundary, temperature, and the prescribed bulk hydrogen fraction of occupied sites. Through this formalism, it is found that hydrogen trapping on grain boundaries clearly correlates with the grain boundary structure (i.e. type of structural unit composing the grain boundary), and the associated grain boundary misorientation. Specifically, for symmetric tilt grain boundaries about the [001] axis, grain boundaries composed of both B and C structural units show a lower segregation susceptibility than other grain boundaries. A direct correlation between the segregation susceptibility and the intrinsic net defect density is provided through the Frank–Bilby formalism. Moreover, the present formulation could prove to be a simple and useful model to identify classes of grain boundaries relevant to grain boundary engineering.

  17. On the interaction of solutes with grain boundaries

    DOE PAGES [OSTI]

    Dingreville, Remi Philippe Michel; Berbenni, Stephane

    2015-11-01

    Solute segregation to grain boundaries is considered by modeling solute atoms as misfitting inclusions within a disclination structural unit model describing the grain boundary structure and its intrinsic stress field. The solute distribution around grain boundaries is described through Fermi–Dirac statistics of site occupancy. The susceptibility of hydrogen segregation to symmetric tilt grain boundaries is discussed in terms of the misorientation angle, the defect type characteristics at the grain boundary, temperature, and the prescribed bulk hydrogen fraction of occupied sites. Through this formalism, it is found that hydrogen trapping on grain boundaries clearly correlates with the grain boundary structure (i.e.more » type of structural unit composing the grain boundary), and the associated grain boundary misorientation. Specifically, for symmetric tilt grain boundaries about the [001] axis, grain boundaries composed of both B and C structural units show a lower segregation susceptibility than other grain boundaries. A direct correlation between the segregation susceptibility and the intrinsic net defect density is provided through the Frank–Bilby formalism. Moreover, the present formulation could prove to be a simple and useful model to identify classes of grain boundaries relevant to grain boundary engineering.« less

  18. Novel 3-D Printed Inverters for Electric Vehicles Can Improve EV Power and Efficiency

    Energy.gov [DOE]

    Plug-in electric vehicle technologies are on their way to being even lighter, more powerful and more efficient with the advent of power inverters created by 3-D printing and novel semiconductors.

  19. "Printing" Tiny Batteries | U.S. DOE Office of Science (SC)

    Office of Science (SC)

    ... Lewis' group has greatly expanded the capabilities of 3D printing. They have designed a broad range of functional inks-inks with useful chemical and electrical properties. And they ...

  20. Global Wind Day 2016 - AMO's Role in Applying 3D Printing to...

    Energy.gov [DOE] (indexed site)

    Global Wind Day 2016 AMOs Role in Applying 3D Printing to Wind Blade Mold Manufacturing Global Wind Day is a worldwide event that occurs annually on June 15 and is ...

  1. The 3D-Printed Shelby Cobra: Defining Rapid Innovation | Department...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    It's been hard to miss in the media and on its almost non-stop road tour, but AMO wanted you to know that our 3D-printed EV version of the 50th anniversary Shelby Cobra just left ...

  2. E-print Network Web Log News: Research Communications for Scientists...

    Office of Scientific and Technical Information (OSTI)

    Description This Web Log provides the latest information about changes to E-print Network ... questions, concerns and other input by using the Contact Us page. Web Log Archive

  3. Frequently Asked Questions (FAQ) for the E-print Network -- Energy...

    Office of Scientific and Technical Information (OSTI)

    ... The E-print Network pulls these vast and widely dispersed data together through a Deep Web ... available on the Web through a browse capability across more than ten thousand sites. ...

  4. Printing a Car: A Team Effort in Innovation | Department of Energy

    Energy Saver

    The story behind the realization of a unique project: the building of a 3D printed electric car, as told by team members. text version Media Coverage of the IMTS Event ...

  5. EERE Success Story-Just Plain Cool, the 3D Printed Shelby Cobra...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    This innovative 3D printing process took just six weeks, and the final result was a glistening roadster fitted with a 100-kilowatt electric motor that can still go zero to 60 mph ...

  6. Researchers find 3-D printed parts to provide low-cost, custom...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Researchers find 3-D printed parts to provide low-cost, custom alternatives for laboratory equipment By Raphael Rosen February 26, 2015 Tweet Widget Google Plus One Share on ...

  7. Notice of Intent to Develop DOE G 436.1-1, Sustainable Print...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    promote energy security, protect the interests of taxpayers, and safeguard the health of the environment. Notice of Intent to Develop DOE G 436.1-1, Sustainable Print Management...

  8. The relationship between grain boundary structure, defect mobility, and grain boundary sink efficiency

    DOE PAGES [OSTI]

    Uberuaga, Blas Pedro; Vernon, Louis J.; Martinez, Enrique; Voter, Arthur F.

    2015-03-13

    Nanocrystalline materials have received great attention due to their potential for improved functionality and have been proposed for extreme environments where the interfaces are expected to promote radiation tolerance. However, the precise role of the interfaces in modifying defect behavior is unclear. Using long-time simulations methods, we determine the mobility of defects and defect clusters at grain boundaries in Cu. We find that mobilities vary significantly with boundary structure and cluster size, with larger clusters exhibiting reduced mobility, and that interface sink efficiency depends on the kinetics of defects within the interface via the in-boundary annihilation rate of defects. Thus,more » sink efficiency is a strong function of defect mobility, which depends on boundary structure, a property that evolves with time. Further, defect mobility at boundaries can be slower than in the bulk, which has general implications for the properties of polycrystalline materials. Finally, we correlate defect energetics with the volumes of atomic sites at the boundary.« less

  9. Analytical Study on Thermal and Mechanical Design of Printed Circuit Heat Exchanger

    SciTech Connect

    Su-Jong Yoon; Piyush Sabharwall; Eung-Soo Kim

    2013-09-01

    The analytical methodologies for the thermal design, mechanical design and cost estimation of printed circuit heat exchanger are presented in this study. In this study, three flow arrangements of parallel flow, countercurrent flow and crossflow are taken into account. For each flow arrangement, the analytical solution of temperature profile of heat exchanger is introduced. The size and cost of printed circuit heat exchangers for advanced small modular reactors, which employ various coolants such as sodium, molten salts, helium, and water, are also presented.

  10. OSTI's E-print Network continues rapid growth | OSTI, US Dept of Energy

    Office of Scientific and Technical Information (OSTI)

    Office of Scientific and Technical Information Office of Scientific & Technical Information NEWS MEDIA CONTACT: Cathey Daniels, (865) 576-9539 FOR IMMEDIATE RELEASE January 17, 2006 OSTI's E-print Network continues rapid growth Created by scientists for scientists, expanded 39 percent in past year Oak Ridge, TN - The E-print Network (www.osti.gov/eprints), a communications hub created by scientists for scientists worldwide, currently provides full-text searching of more than 730,000

  11. Intense X-rays expose tiny flaws in 3-D printed titanium that can lead to

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    breakage over time | Argonne National Laboratory Intense X-rays expose tiny flaws in 3-D printed titanium that can lead to breakage over time By Katie Elyce Jones * March 4, 2016 Tweet EmailPrint Titanium is strong but light - a desirable property among metals. In the twentieth century, titanium was used in military aircraft and equipment and commercial jets. Today, we find this tough and flexible metal all around us - in sports gear, tools, surgical and dental implants, prosthetics,

  12. Earth Sciences Division collected abstracts: 1979

    SciTech Connect

    Henry, A.L.; Schwartz, L.L.

    1980-04-30

    This report is a compilation of abstracts of papers, internal reports, and talks presented during 1979 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract iself is given only under the name of the first author or the first Earth Sciences Division author. A topical index at the end of the report provides useful cross references, while indicating major areas of research interest in the Earth Sciences Division.

  13. Boundary Plasma Turbulence Simulations for Tokamaks

    SciTech Connect

    Xu, X; Umansky, M; Dudson, B; Snyder, P

    2008-05-15

    The boundary plasma turbulence code BOUT models tokamak boundary-plasma turbulence in a realistic divertor geometry using modified Braginskii equations for plasma vorticity, density (ni), electron and ion temperature (T{sub e}; T{sub i}) and parallel momenta. The BOUT code solves for the plasma fluid equations in a three dimensional (3D) toroidal segment (or a toroidal wedge), including the region somewhat inside the separatrix and extending into the scrape-off layer; the private flux region is also included. In this paper, a description is given of the sophisticated physical models, innovative numerical algorithms, and modern software design used to simulate edge-plasmas in magnetic fusion energy devices. The BOUT code's unique capabilities and functionality are exemplified via simulations of the impact of plasma density on tokamak edge turbulence and blob dynamics.

  14. Open Boundary Conditions for Dissipative MHD

    SciTech Connect

    Meier, E T

    2011-11-10

    In modeling magnetic confinement, astrophysics, and plasma propulsion, representing the entire physical domain is often difficult or impossible, and artificial, or 'open' boundaries are appropriate. A novel open boundary condition (BC) for dissipative MHD, called Lacuna-based open BC (LOBC), is presented. LOBC, based on the idea of lacuna-based truncation originally presented by V.S. Ryaben'kii and S.V. Tsynkov, provide truncation with low numerical noise and minimal reflections. For hyperbolic systems, characteristic-based BC (CBC) exist for separating the solution into outgoing and incoming parts. In the hyperbolic-parabolic dissipative MHD system, such separation is not possible, and CBC are numerically unstable. LOBC are applied in dissipative MHD test problems including a translating FRC, and coaxial-electrode plasma acceleration. Solution quality is compared to solutions using CBC and zero-normal derivative BC. LOBC are a promising new open BC option for dissipative MHD.

  15. Inkjet Printed Metallizations for Cu(In1-xGax)Se2 Photovoltaic Cells

    SciTech Connect

    Hersh, P. A.; Curtis, C. J.; van Hest, M. F. A. M.; Kreuder, J. J.; Pasquarelli, R.; Miednaer, A.; Ginley, D. S.

    2011-12-01

    This study reports the inkjet printing of Ag front contacts on Aluminum doped Zinc Oxide (AZO)/intrinsic Zinc Oxide (i-ZnO)/CdS/Cu(In{sub 1-x}Ga{sub x})Se{sub 2} (CIGS)/Mo thin film photovoltaic cells. The printed Ag contacts are being developed to replace the currently employed evaporated Ni/Al bi-layer contacts. Inkjet deposition conditions were optimized to reduce line resistivity and reduce contact resistance to the Al:ZnO layer. Ag lines printed at a substrate temperature of 200 C showed a line resistivity of 2.06 {mu}{Omega} {center_dot} cm and a contact resistance to Al:ZnO of 8.2 {+-} 0.2 m{Omega} {center_dot} cm{sup 2} compared to 6.93 {+-} 0.3 m{Omega} {center_dot} cm{sup 2} for thermally evaporated contacts. These deposition conditions were used to deposit front contacts onto high quality CIGS thin film photovoltaic cells. The heating required to print the Ag contacts caused the performance to degrade compared to similar devices with evaporated Ni/Al contacts that were not heated. Devices with inkjet printed contacts showed 11.4% conversion efficiency compared to 14.8% with evaporated contacts. Strategies to minimize heating, which is detrimental for efficiency, during inkjet printing are proposed.

  16. Screening tests of conformally-coated printed wiring boards

    SciTech Connect

    Skibo, M.D.; Even, W.R.

    1982-03-01

    Identical printed wiring boards (PWB) were fabricated using glass-triazene as substrates and were conformally coated with either conothane or parylene. The boards were then placed in sealed canisters along with TATB and other organic materials found in recent weapon systems. While subjected to electrical potentials of 120V and 250V, these PWBs were either aged at 60/sup 0/, 70/sup 0/, or 80/sup 0/ or temperature cycled for as long as 16 months. The resistivities of the boards were precisely measured before and after aging to determine the effect of time, temperature, and environment on the electrical characteristics of board materials. In all cases board resistivity increased with temperature and duration of test. This increase was believed to be related to either a reduction in water content in the board substrate or a completion of cure of the conformal coating with time elevated temperature. Both mechanisms would result in a reduction in conductive species. In spite of high humidity levels, no evidence of current - activated filament formation between adjacent active circuit paths on aged PWBs was seen. Similarly, soldered contacts were free of thermally-induced fatigue damage after as many as 500 cycles between -54 and 70/sup 0/C at 1 cycle/day.

  17. OSTIblog Articles in the earth systems modeling Topic | OSTI...

    Office of Scientific and Technical Information (OSTI)

    earth systems modeling Topic ACME - Perfecting Earth System Models by Kathy Chambers 29 Oct, 2014 in Earth system modeling as we know it and how it benefits climate change research ...

  18. An Earth-Friendly Wind Vision | Department of Energy

    Energy Saver

    An Earth-Friendly Wind Vision An Earth-Friendly Wind Vision April 22, 2015 - 7:30am Addthis An Earth-Friendly Wind Vision Wind energy is a clean, domestic energy source that ...

  19. Rare Earth Metals for Science | The Ames Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Rare Earth Metals for Science The Ames Laboratory has been actively involved in the ... More information on the rare-earth elements Quantities of high-purity rare earth metals ...

  20. News about Rare Earths, New or Critical Materials, and Their...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Rare Earths, New or Critical Materials, and Their Uses: 2016 Rare earth materials: Developing ... UK gets federal funds to research coal-based rare earth elements, Dec. 20, 2015 Salvage ...

  1. How Are You Celebrating Earth Day This Year? | Department of...

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Day This Year? How Are You Celebrating Earth Day This Year? April 21, 2011 - 7:30am Addthis Tomorrow is Earth Day We've already written about how you can resolve to make Earth Day ...

  2. Earth Day Events Flyer 2016 | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Events Flyer 2016 Earth Day Events Flyer 2016 The schedule of events for the 2016 Department of Energy Earth Day activities. PDF icon Earth Day Events Flyer 2016 More Documents & ...

  3. Boundary acquisition for setup of numerical simulation

    SciTech Connect

    Diegert, C.

    1997-12-31

    The author presents a work flow diagram that includes a path that begins with taking experimental measurements, and ends with obtaining insight from results produced by numerical simulation. Two examples illustrate this path: (1) Three-dimensional imaging measurement at micron scale, using X-ray tomography, provides information on the boundaries of irregularly-shaped alumina oxide particles held in an epoxy matrix. A subsequent numerical simulation predicts the electrical field concentrations that would occur in the observed particle configurations. (2) Three-dimensional imaging measurement at meter scale, again using X-ray tomography, provides information on the boundaries fossilized bone fragments in a Parasaurolophus crest recently discovered in New Mexico. A subsequent numerical simulation predicts acoustic response of the elaborate internal structure of nasal passageways defined by the fossil record. The author must both add value, and must change the format of the three-dimensional imaging measurements before the define the geometric boundary initial conditions for the automatic mesh generation, and subsequent numerical simulation. The author applies a variety of filters and statistical classification algorithms to estimate the extents of the structures relevant to the subsequent numerical simulation, and capture these extents as faceted geometries. The author will describe the particular combination of manual and automatic methods used in the above two examples.

  4. Planning for Earth Day | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    not do something for the good ol' Earth and save a little energy at the same time? We talk a lot about insulation and home energy audits and other fancy stuff, but energy saving...

  5. Ames Lab 101: Rare-Earth Magnets

    SciTech Connect

    McCallum, Bill

    2010-01-01

    Senior Scientist, Bill McCallum, briefly discusses rare-earth magnets and their uses and how Ames Lab is research new ways to save money and energy using magnets.

  6. Earth-Abundant Materials | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    CZTS PV cell: Mo-coated substrate, CZTS light absorber, n- CdS, i-ZnO, and transparent conductive oxide. DOE funds research into Earth-abundant materials for thin-film solar ...

  7. Earth Day, Every Day | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Week festivities at our headquarters here in Washington, D.C. throughout this week. This year's theme is "Earth Day, Every Day Changing Behavior to Reduce DOE's Carbon Footprint." ...

  8. Google Earth Tour: Waters LANL Protects

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Home > Clean the Past > What waters does LANL protect? PreviousNext Google Earth Tour: Waters LANL Protects Click here to load the tour...then click the play button below...

  9. New Earth Energy Limited | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Zip: BH31 6AT Sector: Renewable Energy Product: UK-based subsidiary of British waste treatment and renewable energy company New Earth Group, formed to deploy thermal conversion...

  10. Ames Lab 101: Rare-Earth Magnets

    ScienceCinema

    McCallum, Bill

    2012-08-29

    Senior Scientist, Bill McCallum, briefly discusses rare-earth magnets and their uses and how Ames Lab is research new ways to save money and energy using magnets.

  11. Boundary Entropy Can Increase Under Bulk RG Flow (Journal Article...

    Office of Scientific and Technical Information (OSTI)

    Boundary Entropy Can Increase Under Bulk RG Flow Citation Details In-Document Search Title: Boundary Entropy Can Increase Under Bulk RG Flow You are accessing a document from ...

  12. A Scalable and Extensible Earth System Model for Climate Change...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: A Scalable and Extensible Earth System Model for Climate Change Science Citation Details In-Document Search Title: A Scalable and Extensible Earth System Model ...

  13. Preparations of rare earth-iron alloys by thermite reduction

    DOEpatents

    Schmidt, Frederick A.; Peterson, David T.; Wheelock, John T.

    1986-09-16

    An improved method for the preparation of high-purity rare earth-iron alloys by the aluminothermic reduction of a mixture of rare earth and iron fluorides.

  14. Climate Change as Recorded in Earth Surface Processes

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    climate change earth surface processes Climate Change as Recorded in Earth Surface Processes Not surprisingly significant changes in climate leave their imprint on the landscape. ...

  15. Agencies, Hoping to Deflect Comets and Asteroids, Step Up Earth...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Agencies, Hoping to Deflect Comets and Asteroids, Step Up Earth Defense Agencies, Hoping to Deflect Comets and Asteroids, Step Up Earth Defense In grappling with the threat of ...

  16. Earth Week 2015 Schedule of Events | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Schedule of Events Schedule of Events for Energy Department Earth Week 2015 PDF icon doeearthday2015schedule.pdf More Documents & Publications DOE Headquarters Earth Day 2015...

  17. ORNL Licenses Rare Earth Magnet Recycling Process to Momentum...

    Office of Environmental Management (EM)

    ORNL Licenses Rare Earth Magnet Recycling Process to Momentum Technologies ORNL Licenses ... Dallas-based Momentum Technologies is focused on extraction of rare earth elements and ...

  18. Characterization and Recovery of Rare Earths from Coal and By...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: Characterization and Recovery of Rare Earths from Coal and By-Products Citation Details In-Document Search Title: Characterization and Recovery of Rare Earths ...

  19. Evolution Energy formerly Earth Biofuels Inc | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Energy formerly Earth Biofuels Inc Jump to: navigation, search Name: Evolution Energy (formerly Earth Biofuels Inc) Place: Dallas, Texas Zip: 75205 Sector: Renewable Energy...

  20. Transport of transient solar wind particles in Earth's cusps...

    Office of Scientific and Technical Information (OSTI)

    Transport of transient solar wind particles in Earth's cusps Citation Details In-Document Search Title: Transport of transient solar wind particles in Earth's cusps An important ...

  1. Nan Sauer named Associate Director for Chemistry, Life, and Earth...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Sauer named AD for Chemistry, Life, and Earth Sciences Nan Sauer named Associate Director for Chemistry, Life, and Earth Sciences Sauer has a distinguished track record as a ...

  2. New Model of Earth's Interior Reveals Clues to Hotspot Volcanoes

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    detected previously unknown channels of slow-moving seismic waves in Earth's upper mantle. ... computer simulations of how these waves travel through the Earth's mantle- the ...

  3. Seismic Imaging of the Earth's Interior (LBNL Summer Lecture Series)

    ScienceCinema

    Romanowicz, Barbara

    2011-04-28

    Summer Lecture Series 2006: Earth scientist Barbara Romanowicz discusses how she explores the deep structure and dynamics of the Earth using seismic tomography.

  4. USGS-Earth Resources Observation and Science (EROS) Center |...

    OpenEI (Open Energy Information) [EERE & EIA]

    USGS-Earth Resources Observation and Science (EROS) Center Jump to: navigation, search Tool Summary LAUNCH TOOL Name: USGS-Earth Resources Observation and Science (EROS) Center...

  5. Ternary rare earth-lanthanide sulfides

    DOEpatents

    Takeshita, Takuo; Gschneidner, Jr., Karl A.; Beaudry, Bernard J.

    1987-01-06

    A new ternary rare earth sulfur compound having the formula: La.sub.3-x M.sub.x S.sub.4 where M is a rare earth element selected from the group europium, samarium and ytterbium and x=0.15 to 0.8. The compound has good high-temperature thermoelectric properties and exhibits long-term structural stability up to 1000.degree. C.

  6. Lab joins in global Earth Day celebrations

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Lab joins in global Earth Day celebrations Community Connections: Your link to news and opportunities from Los Alamos National Laboratory Latest Issue:November 2, 2016 all issues All Issues » submit Lab joins in global Earth Day celebrations A personal message from Laboratory Director Charlie McMillan April 1, 2014 Charlie McMillan, Laboratory Director Charlie McMillan, Laboratory Director Contacts Community Programs Office Director Kurt Steinhaus Email Editor Linda Anderman Email Los Alamos

  7. Earth Sciences Division collected abstracts: 1980

    SciTech Connect

    Henry, A.L.; Hornady, B.F.

    1981-10-15

    This report is a compilation of abstracts of papers, reports, and talks presented during 1980 at national and international meetings by members of the Earth Sciences Division, Lawrence Livermore National Laboratory. The arrangement is alphabetical (by author). For a given report, a bibliographic reference appears under the name of each coauthor, but the abstract itself is given only under the name of the first author (indicated in capital letters) or the first Earth Sciences Division author.

  8. Earth Sciences Division annual report 1989

    SciTech Connect

    Not Available

    1990-06-01

    This Annual Report presents summaries of selected representative research activities from Lawrence Berkeley Laboratory grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrology, Geology and Geochemistry, and Geophysics and Geomechanics. We are proud to be able to bring you this report, which we hope will convey not only a description of the Division's scientific activities but also a sense of the enthusiasm and excitement present today in the Earth Sciences.

  9. Constructing earth sheltered housing with concrete

    SciTech Connect

    Spears, R.E.

    1981-01-01

    This manual provides a state - of - the - art review of the design and construction of an earth - sheltered house using cast - in - place concrete, precast concrete, and concrete masonry. Based on a literature survey, theoretical work, and discussions with researchers and engineers in the concrete industry, the text is designed for use by architects, engineers, and homebuilders. The features of concrete construction that are current accepted practice for the concrete products discussed are shown to be applicable with reasonable care to building a safe, dry, and comfortable earth - sheltered house. The main considerations underlying the recommendations were the use of the earth's mass and passive solar effects to minimize energy needs, the structural capacity of the separate concrete products and their construction methods, and drainage principles and waterproofing details. Shelter ranging from those with at least 2 feet of earth cover to those with an uncovered roof of usual construction are included. To be considered an earth - sheltered residential building, at least half of the exterior wall and roof area that is in direct contact with the conditioned living space must be sheltered from the environment by earth berm or earthfill. Siting considerations, the fundamentals of passive solar heating, planning considerations, and structural considerations are discussed. Detailed guidelines are provided on concrete masonry construction, joint details in walls and floors, waterproofing, formwork and form removal, concrete construction practices, concrete masonry, and surface finishes. Numerous illustrations, tables, and a list of 32 references are provided. (Author abstract modified).

  10. Planetary Boundary Layer from AERI and MPL (Dataset) | Data Explorer

    Office of Scientific and Technical Information (OSTI)

    Planetary Boundary Layer from AERI and MPL Title: Planetary Boundary Layer from AERI and MPL The distribution and transport of aerosol emitted to the lower troposphere is governed by the height of the planetary boundary layer (PBL), which limits the dilution of pollutants and influences boundary-layer convection. Because radiative heating and cooling of the surface strongly affect the PBL top height, it follows diurnal and seasonal cycles and may vary by hundreds of meters over a 24-hour period.

  11. Stable Boundary Layer Education (STABLE) Final Campaign Summary (Technical

    Office of Scientific and Technical Information (OSTI)

    Report) | SciTech Connect Stable Boundary Layer Education (STABLE) Final Campaign Summary Citation Details In-Document Search Title: Stable Boundary Layer Education (STABLE) Final Campaign Summary The properties of, and the processes that occur in, the nocturnal stable boundary layer are not well understood, making it difficult to represent adequately in numerical models. The nocturnal boundary layer often is characterized by a temperature inversion and, in the Southern Great Plains region,

  12. Evolution of Grain Boundary Networks in Extreme Radiation Environments

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    of the Evolution of Grain Boundary Networks in Extreme Radiation Environments. Evolution of Grain Boundary Networks in Extreme Radiation Environments Research Our objective is to understand the characteristics of an "optimal" grain boundary (GB) network that minimizes microstructural evolution in radiation environments. Through our research we have elucidated that this optimal network requires a balance between two populations of grain boundaries: low free volume (low free energy)

  13. Infiltration of Nanoparticles into Porous Binder Jet Printed Parts

    DOE PAGES [OSTI]

    Elliott, Amelia; AlSalihi, Sarah; Merriman, Abbey L.; Basti, Mufeed M.

    2016-01-01

    The densification of parts that are produced by binder jetting Additive Manufacturing (AM; a.k.a. “3D Printing”) is an essential step in making them mechanically useful. By increasing the packing factor of the powder bed by incorporating nanoparticles into the binder has potential to alleviate the amount of shrinkage needed for full densification of binder jet parts. We present preliminary data on the use of 316L Stainless Steel Nanoparticles (SSN) to densify 316L stainless steel binder jet parts. Aqueous solutions of Diethylene Glycol (DEG) or Ethylene Glycol (EG) were prepared at different DEG/water and EG/water molar ratios; pH of the solutionsmore » was adjusted by the use of 0.10 M sodium hydroxide. Nanoparticles were suspended in a resulted solution at a volume percentage of SSN/solution at 0.5%. The suspension was then sonicated for thirty minutes. One milliliter of the suspension was added stepwise to a sintered, printed disk with the dimensions: (d = 10 mm, h = 3 mm) in the presence of a small magnet. The 3D part was then sintered again. Moreover, the increase in the mass of the 3D part was used as indication of the amount of nanoparticles that diffused in the 3D part. This mass percent increase was studied as a function of pH of the suspension and as function DEG/water molar ratio. Unlike EG, data show that change in pH affects the mass percent when the suspension was made with DEG. Finally, optical analysis of the discs’ cross sections revealed trends metallic densities similar to trends in the data for mass increase with changing pH and water molar ratio.« less

  14. Infiltration of Nanoparticles into Porous Binder Jet Printed Parts

    SciTech Connect

    Elliott, Amelia; AlSalihi, Sarah; Merriman, Abbey L.; Basti, Mufeed M.

    2016-01-01

    The densification of parts that are produced by binder jetting Additive Manufacturing (AM; a.k.a. “3D Printing”) is an essential step in making them mechanically useful. By increasing the packing factor of the powder bed by incorporating nanoparticles into the binder has potential to alleviate the amount of shrinkage needed for full densification of binder jet parts. We present preliminary data on the use of 316L Stainless Steel Nanoparticles (SSN) to densify 316L stainless steel binder jet parts. Aqueous solutions of Diethylene Glycol (DEG) or Ethylene Glycol (EG) were prepared at different DEG/water and EG/water molar ratios; pH of the solutions was adjusted by the use of 0.10 M sodium hydroxide. Nanoparticles were suspended in a resulted solution at a volume percentage of SSN/solution at 0.5%. The suspension was then sonicated for thirty minutes. One milliliter of the suspension was added stepwise to a sintered, printed disk with the dimensions: (d = 10 mm, h = 3 mm) in the presence of a small magnet. The 3D part was then sintered again. Moreover, the increase in the mass of the 3D part was used as indication of the amount of nanoparticles that diffused in the 3D part. This mass percent increase was studied as a function of pH of the suspension and as function DEG/water molar ratio. Unlike EG, data show that change in pH affects the mass percent when the suspension was made with DEG. Finally, optical analysis of the discs’ cross sections revealed trends metallic densities similar to trends in the data for mass increase with changing pH and water molar ratio.

  15. GRAIN BOUNDARY STRENGTHENING PROPERTIES OF TUNGSTEN ALLOYS

    SciTech Connect

    Setyawan, Wahyu; Kurtz, Richard J.

    2012-10-10

    Density functional theory was employed to investigate grain boundary (GB) properties of W alloys. A range of substitutional solutes across the Periodic Table was investigated to understand the behavior of different electronic orbitals in changing the GB cleavage energy in the Σ27a[110]{525} GB. A number of transition metals were predicted to enhance the GB cohesion. This includes Ru, Re, Os, Ir, V, Cr, Mn, Fe, Co, Ti, Hf, Ta and Nb. While lanthanides, s and p elements were tended to cause GB embrittlement.

  16. Earth Sciences Division annual report 1990

    SciTech Connect

    1991-06-01

    This Annual Report presents summaries of selected representative research activities grouped according to the principal disciplines of the Earth Sciences Division: Reservoir Engineering and Hydrogeology, Geology and Geochemistry, and Geophysics and Geomechanics. Much of the Division`s research deals with the physical and chemical properties and processes in the earth`s crust, from the partially saturated, low-temperature near-surface environment to the high-temperature environments characteristic of regions where magmatic-hydrothermal processes are active. Strengths in laboratory and field instrumentation, numerical modeling, and in situ measurement allow study of the transport of mass and heat through geologic media -- studies that now include the appropriate chemical reactions and the hydraulic-mechanical complexities of fractured rock systems. Of particular note are three major Division efforts addressing problems in the discovery and recovery of petroleum, the application of isotope geochemistry to the study of geodynamic processes and earth history, and the development of borehole methods for high-resolution imaging of the subsurface using seismic and electromagnetic waves. In 1989 a major DOE-wide effort was launched in the areas of Environmental Restoration and Waste Management. Many of the methods previously developed for and applied to deeper regions of the earth will in the coming years be turned toward process definition and characterization of the very shallow subsurface, where man-induced contaminants now intrude and where remedial action is required.

  17. Structural color printing based on plasmonic metasurfaces of perfect light absorption

    DOE PAGES [OSTI]

    Cheng, Fei; Gao, Jie; Luk, Ting S.; Yang, Xiaodong

    2015-06-05

    Subwavelength structural color filtering and printing technologies employing plasmonic nanostructures have recently been recognized as an important and beneficial complement to the traditional colorant-based pigmentation. However, the color saturation, brightness and incident angle tolerance of structural color printing need to be improved to meet the application requirement. Here we demonstrate a structural color printing method based on plasmonic metasurfaces of perfect light absorption to improve color performances such as saturation and brightness. Thin-layer perfect absorbers with periodic hole arrays are designed at visible frequencies and the absorption peaks are tuned by simply adjusting the hole size and periodicity. Near perfectmore » light absorption with high quality factors are obtained to realize high-resolution, angle-insensitive plasmonic color printing with high color saturation and brightness. Moreover, the fabricated metasurfaces can be protected with a protective coating for ambient use without degrading performances. The demonstrated structural color printing platform offers great potential for applications ranging from security marking to information storage.« less

  18. Structural color printing based on plasmonic metasurfaces of perfect light absorption

    SciTech Connect

    Cheng, Fei; Gao, Jie; Luk, Ting S.; Yang, Xiaodong

    2015-06-05

    Subwavelength structural color filtering and printing technologies employing plasmonic nanostructures have recently been recognized as an important and beneficial complement to the traditional colorant-based pigmentation. However, the color saturation, brightness and incident angle tolerance of structural color printing need to be improved to meet the application requirement. Here we demonstrate a structural color printing method based on plasmonic metasurfaces of perfect light absorption to improve color performances such as saturation and brightness. Thin-layer perfect absorbers with periodic hole arrays are designed at visible frequencies and the absorption peaks are tuned by simply adjusting the hole size and periodicity. Near perfect light absorption with high quality factors are obtained to realize high-resolution, angle-insensitive plasmonic color printing with high color saturation and brightness. Moreover, the fabricated metasurfaces can be protected with a protective coating for ambient use without degrading performances. The demonstrated structural color printing platform offers great potential for applications ranging from security marking to information storage.

  19. RACORO long-term, systematic aircraft observations of boundary layer clouds

    SciTech Connect

    Vogelmann, A.M.; McFarquhar, G.; Ogren, J.; Turner, D. D.; Comstock, J. M.; Feingold, G.; Long, C. N.; Jonsson, H. H.; Bucholtz, A.; Collins, D. R.; Diskin, G.; Gerber, H.; Lawson, R. P.; Woods, R. K.; Hubbe, J.; Tomlinson, J.; Schmid, B.

    2010-06-27

    Our knowledge of boundary layer cloud processes is insufficient to resolve pressing scientific problems. Boundary layer clouds often have liquid-water paths (LWPs) less than 100 gm{sup 2}, which are defined here as being 'thin' Clouds with Low Optical Water Depths (CLOWD). This type of cloud is common globally, and the Earth's radiative energy balance is particularly sensitive to small changes in their optical properties. However, it is difficult to retrieve accurately their cloud properties via remote sensing because they are tenuous and often occur in partly cloudy skies. This interferes with our ability to obtain the routine, long-term statistics needed to improve their representation in climate models. To address this problem, in-situ data are needed to investigate cloud processes and to evaluate and refine existing retrieval algorithms. Coordinated by the ARM Aerial Facility (AAF), the Routine AAF CLOWD Optical Radiative Observations (RACORO) field campaign conducted long-term, systematic flights in boundary layer, liquid-water clouds over the ARM Southern Great Plains (SGP) site between 22 January and 30 June 2009. This was the first time that a long-term aircraft campaign was undertaken for systematic in-situ sampling of cloud properties. Using the CIRPAS Twin Otter aircraft equipped with a comprehensive set of instruments to measure solar and thermal radiation, cloud microphysics, aerosol properties and atmospheric state, the RACORO team logged an unprecedented 59 flights and 259 research hours above the SGP site. Data gathered during the RACORO campaign will provide researchers with a statistically relevant data set of boundary-layer cloud and aerosol properties for future study. These data can be used to validate retrieval algorithms and support process studies and model simulations of boundary layer clouds and, in particular, CLOWD-type clouds. In addition to cloud observations, complementary clear-sky flight patterns were conducted to map the surface

  20. Rare earth phosphors and phosphor screens

    DOEpatents

    Buchanan, Robert A.; Maple, T. Grant; Sklensky, Alden F.

    1981-01-01

    This invention relates to rare earth phosphor screens for converting image carrying incident radiation to image carrying visible or near-visible radiation and to the rare earth phosphor materials utilized in such screens. The invention further relates to methods for converting image carrying charged particles to image carrying radiation principally in the blue and near-ultraviolet region of the spectrum and to stabilized rare earth phosphors characterized by having a continuous surface layer of the phosphors of the invention. More particularly, the phosphors of the invention are oxychlorides and oxybromides of yttrium, lanthanum and gadolinium activated with trivalent cerium and the conversion screens are of the type illustratively including x-ray conversion screens, image amplifier tube screens, neutron imaging screens, cathode ray tube screens, high energy gamma ray screens, scintillation detector screens and screens for real-time translation of image carrying high energy radiation to image carrying visible or near-visible radiation.

  1. Earth Sciences report, 1989--1990

    SciTech Connect

    Younker, L.W.; Peterson, S.J.; Price, M.E.

    1991-03-01

    The Earth Sciences Department at Lawrence Livermore National Laboratory (LLNL) conducts work in support of the Laboratory's energy, defense, environmental, and basic research programs. The Department comprises more than 100 professional scientific personnel spanning a variety of subdisciplines: geology, seismology, physics, geophysics, geochemistry, geohydrology, chemical engineering, and mechanical engineering. Resident technical support groups add significant additional technical expertise, including Containment Engineering, Computations, Electronic Engineering, Mechanical Engineering, Chemistry and Materials Science, and Technical Information. In total, approximately 180 professional scientists and engineers are housed in the Earth Sciences Department, making it one of the largest geo-science research groups in the nation. Previous Earth Sciences reports have presented an outline of the technical capabilities and accomplishments of the groups within the Department. In this FY 89/90 Report, we have chosen instead to present twelve of our projects in full-length technical articles. This Overview introduces those articles and highlights other significant research performed during this period.

  2. Solar Power Beaming: From Space to Earth

    SciTech Connect

    Rubenchik, A M; Parker, J M; Beach, R J; Yamamoto, R M

    2009-04-14

    Harvesting solar energy in space and power beaming the collected energy to a receiver station on Earth is a very attractive way to help solve mankind's current energy and environmental problems. However, the colossal and expensive 'first step' required in achieving this goal has to-date stifled its initiation. In this paper, we will demonstrate that recent advance advances in laser and optical technology now make it possible to deploy a space-based system capable of delivering 1 MW of energy to a terrestrial receiver station, via a single unmanned commercial launch into Low Earth Orbit (LEO). Figure 1 depicts the overall concept of our solar power beaming system, showing a large solar collector in space, beaming a coherent laser beam to a receiving station on Earth. We will describe all major subsystems and provide technical and economic discussion to support our conclusions.

  3. A CONTINUUM OF PLANET FORMATION BETWEEN 1 AND 4 EARTH RADII

    SciTech Connect

    Schlaufman, Kevin C.

    2015-02-01

    It has long been known that stars with high metallicity are more likely to host giant planets than stars with low metallicity. Yet the connection between host star metallicity and the properties of small planets is only just beginning to be investigated. It has recently been argued that the metallicity distribution of stars with exoplanet candidates identified by Kepler provides evidence for three distinct clusters of exoplanets, distinguished by planet radius boundaries at 1.7 R{sub ⨁} and 3.9 R{sub ⨁}. This would suggest that there are three distinct planet formation pathways for super-Earths, mini-Neptunes, and giant planets. However, as I show through three independent analyses, there is actually no evidence for the proposed radius boundary at 1.7 R{sub ⨁}. On the other hand, a more rigorous calculation demonstrates that a single, continuous relationship between planet radius and metallicity is a better fit to the data. The planet radius and metallicity data therefore provides no evidence for distinct categories of small planets. This suggests that the planet formation process in a typical protoplanetary disk produces a continuum of planet sizes between 1 R{sub ⨁} and 4 R{sub ⨁}. As a result, the currently available planet radius and metallicity data for solar-metallicity F and G stars give no reason to expect that the amount of solid material in a protoplanetary disk determines whether super-Earths or mini-Neptunes are formed.

  4. Amphoteric doping of praseodymium Pr3+ in SrTiO3 grain boundaries

    SciTech Connect

    Yang, H.; Lee, H. S.; Kotula, P. G.; Sato, Y.; Ikuhara, Y.; Browning, N. D.

    2015-03-26

    Charge Compensation in rare-earth Praseodymium (Pr3+) doped SrTiO3 plays an important role in determining the overall photoluminescence properties of the system. Here, the Pr3+ doping behavior in SrTiO3 grain boundaries (GBs) is analyzed using aberration corrected scanning transmission electron microscopy (STEM). The presence of Pr3+ induces structure variations and changes the statistical prevalence of GB structures. In contrast to the assumption that Pr3+ substitutes for A site as expected in the bulk, Pr3+ is found to substitute both Sr and Ti sites inside GBs with the highest concentration in the Ti sites. As a result, this amphoteric doping behavior in the boundary plane is further confirmed by first principles theoretical calculations.

  5. Alkaline earth filled nickel skutterudite antimonide thermoelectrics

    DOEpatents

    Singh, David Joseph

    2013-07-16

    A thermoelectric material including a body centered cubic filled skutterudite having the formula A.sub.xFe.sub.yNi.sub.zSb.sub.12, where A is an alkaline earth element, x is no more than approximately 1.0, and the sum of y and z is approximately equal to 4.0. The alkaline earth element includes guest atoms selected from the group consisting of Be, Mb, Ca, Sr, Ba, Ra and combinations thereof. The filled skutterudite is shown to have properties suitable for a wide variety of thermoelectric applications.

  6. Flow-enhanced solution printing of all-polymer solar cells

    SciTech Connect

    Diao, Ying; Zhou, Yan; Kurosawa, Tadanori; Shaw, Leo; Wang, Cheng; Park, Steve; Guo, Yikun; Reinspach, Julia A.; Gu, Kevin; Gu, Xiaodan; Tee, Benjamin C. K.; Pang, Changhyun; Yan, Hongping; Zhao, Dahui; Toney, Michael F.; Mannsfeld, Stefan C. B.; Bao, Zhenan

    2015-08-12

    Morphology control of solution coated solar cell materials presents a key challenge limiting their device performance and commercial viability. Here we present a new concept for controlling phase separation during solution printing using an all-polymer bulk heterojunction solar cell as a model system. The key aspect of our method lies in the design of fluid flow using a microstructured printing blade, on the basis of the hypothesis of flow-induced polymer crystallization. Our flow design resulted in a similar to 90% increase in the donor thin film crystallinity and reduced microphase separated donor and acceptor domain sizes. The improved morphology enhanced all metrics of solar cell device performance across various printing conditions, specifically leading to higher short-circuit current, fill factor, open circuit voltage and significantly reduced device-to-device variation. However, we expect our design concept to have broad applications beyond all-polymer solar cells because of its simplicity and versatility.

  7. Printed assemblies of ultrathin, microscale inorganic light emitting diodes for deformable and semitransparent displays

    DOEpatents

    Rogers, John A; Nuzzo, Ralph; Kim, Hoon-sik; Brueckner, Eric; Park, Sang Il; Kim, Rak Hwan

    2014-10-21

    Described herein are printable structures and methods for making, assembling and arranging electronic devices. A number of the methods described herein are useful for assembling electronic devices where one or more device components are embedded in a polymer which is patterned during the embedding process with trenches for electrical interconnects between device components. Some methods described herein are useful for assembling electronic devices by printing methods, such as by dry transfer contact printing methods. Also described herein are GaN light emitting diodes and methods for making and arranging GaN light emitting diodes, for example for display or lighting systems.

  8. Using 3D Printing to Redesign Santa's Sleigh | GE Global Research

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Using 3D Printing to Redesign Santa's Sleigh Click to email this to a friend (Opens in new window) Share on Facebook (Opens in new window) Click to share (Opens in new window) Click to share on LinkedIn (Opens in new window) Click to share on Tumblr (Opens in new window) Using 3D Printing to Redesign Santa's Sleigh Thomas The Elf 2013.12.03 Hello Everyone! I am so excited to be back this year to share another way GE researchers are taking part in the holiday cheer. In the past, we've utilized GE

  9. Connect to researchers around the world at OSTI's E-Print Network | OSTI,

    Office of Scientific and Technical Information (OSTI)

    US Dept of Energy Office of Scientific and Technical Information Connect to researchers around the world at OSTI's E-Print Network Back to the OSTI News Listing for 2008 You can browse more than 28,500 Web sites of researchers from around the world, read their abstracts, download their papers, and explore their research institutions, all at OSTI's E-print Network. This rapidly growing service is free and open to the public. Simply go to the browse by disciplines page, and select from an

  10. Sintering Kinetics of Inkjet Printed Conductive Silver Lines on Insulating Plastic Substrate

    DOE PAGES [OSTI]

    Zhou, Wenchao; List, III, Frederick Alyious; Duty, Chad E; Babu, Sudarsanam Suresh

    2015-01-24

    This paper focuses on sintering kinetics of inkjet printed lines containing silver nanoparticles deposited on a plastic substrate. Upon heat treatment, the change of resistance in the printed lines was measured as a function of time and sintering temperatures from 150 to 200 C. A critical temperature was observed for the sintering process, beyond which there was no further reduction in resistance. Analysis shows the critical temperature correlates to the boiling point of the solvent, which is attributed to a liquid-mediated sintering mechanism. It is demonstrated that the sintering process shuts down after the solvent has completely evaporated.

  11. Labs in NNSA lead the way in 3D printing - the next industrial revolution

    National Nuclear Security Administration (NNSA)

    | National Nuclear Security Administration | (NNSA) Labs in NNSA lead the way in 3D printing - the next industrial revolution Monday, June 13, 2016 - 10:29am The power to create useful items from raw materials recently entered regular homes via small-scale 3D-printers, but the concept of additive manufacturing isn't so new. From defense, aerospace, automotive, medicine, and metals manufacturing, the capabilities enabled by 3D printing have wide-reaching effects. Additive manufacturing builds

  12. Crystalline rare-earth activated oxyorthosilicate phosphor

    DOEpatents

    McClellan, Kenneth J.; Cooke, D. Wayne

    2004-02-10

    Crystalline, transparent, rare-earth activated lutetium oxyorthosilicate phosphor. The phosphor consists essentially of lutetium yttrium oxyorthosilicate activated with a rare-earth metal dopant M and having the general formula Lu(.sub.2-x-z)Y.sub.x M.sub.z SiO.sub.5, wherein 0.00.ltoreq.x.ltoreq.1.95, wherein 0.001.ltoreq.z.ltoreq.0.02, and wherein M is selected from Sm, Tb, Tm, Eu, Yb, and Pr. The phosphor also consists essentially of lutetium gadolinium oxyorthosilicate activated with a rare-earth metal dopant M and having the general formula Lu(.sub.2-x-z)Gd.sub.x M.sub.z SiO.sub.5, wherein 0.00.ltoreq.x.ltoreq.1.95, wherein 0.001.ltoreq.z.ltoreq.0.02, and wherein M is selected from Sm, Tb, Tm, Eu, Yb, and Pr. The phosphor also consists essentially of gadolinium yttrium oxyorthosilicate activated with a rare-earth metal dopant M and having the general formula Gd(.sub.2-x-z)Y.sub.x M.sub.z SiO.sub.5, wherein 0.00.ltoreq.x.ltoreq.1.95, wherein 0.001.ltoreq.z.ltoreq.0.02, and wherein M is selected from Sm, Tb, Tm, Eu, Yb, and Pr. The phosphor may be optically coupled to a photodetector to provide a radiation detector.

  13. Replacing the Rare Earth Intellectual Capital

    SciTech Connect

    Gschneidner, Jr., Karl

    2011-04-01

    The rare earth crisis slowly evolved during a 10 to 15 year period beginning in the mid-1980s, when the Chinese began to export mixed rare earth concentrates. In the early 1990s, they started to move up the supply chain and began to export the individual rare earth oxides and metals. By the late 1990s the Chinese exported higher value products, such as magnets, phosphors, polishing compounds, catalysts; and in the 21st century they supplied finished products including electric motors, computers, batteries, liquid-crystal displays (LCDs), TVs and monitors, mobile phones, iPods and compact fluorescent lamp (CFL) light bulbs. As they moved to higher value products, the Chinese slowly drove the various industrial producers and commercial enterprises in the US, Europe and Japan out of business by manipulating the rare earth commodity prices. Because of this, the technically trained rare earth engineers and scientists who worked in areas from mining to separations, to processing to production, to manufacturing of semifinished and final products, were laid-off and moved to other fields or they retired. However, in the past year the Chinese have changed their philosophy of the 1970s and 1980s of forming a rare earth cartel to control the rare earth markets to one in which they will no longer supply the rest of the world (ROW) with their precious rare earths, but instead will use them internally to meet the growing demand as the Chinese standard of living increases. To this end, they have implemented and occasionally increased export restrictions and added an export tariff on many of the high demand rare earth elements. Now the ROW is quickly trying to start up rare earth mines, e.g. Molycorp Minerals in the US and Lynas Corp. in Australia, to cover this shortfall in the worldwide market, but it will take about five years for the supply to meet the demand, even as other mines in the ROW become productive. Unfortunately, today there is a serious lack of technically trained

  14. Earth Sciences Department Annual Report, 1984

    SciTech Connect

    Henry, A.L.; Donohue, M.L.

    1985-09-01

    The Earth Sciences Department at Lawrence Livermore National Laboratory comprises nine different disciplinary and programmatic groups that provide research in the geosciences, including nuclear waste management, containment of nuclear weapons tests, seismic treaty verification, stimulation of natural gas production by unconventional means, and oil shale retorting. Each group's accomplishments in 1984 are discussed, followed by a listing of the group's publications for the year.

  15. Atomistic simulations of dislocation pileup: Grain boundaries interaction

    DOE PAGES [OSTI]

    Wang, Jian

    2015-05-27

    Here, using molecular dynamics (MD) simulations, we studied the dislocation pileup–grain boundary (GB) interactions. Two Σ11 asymmetrical tilt grain boundaries in Al are studied to explore the influence of orientation relationship and interface structure on dislocation activities at grain boundaries. To mimic the reality of a dislocation pileup in a coarse-grained polycrystalline, we optimized the dislocation population in MD simulations and developed a predict-correct method to create a dislocation pileup in MD simulations. MD simulations explored several kinetic processes of dislocations–GB reactions: grain boundary sliding, grain boundary migration, slip transmission, dislocation reflection, reconstruction of grain boundary, and the correlation ofmore » these kinetic processes with the available slip systems across the GB and atomic structures of the GB.« less

  16. Atomistic simulations of dislocation pileup: Grain boundaries interaction

    SciTech Connect

    Wang, Jian

    2015-05-27

    Here, using molecular dynamics (MD) simulations, we studied the dislocation pileup–grain boundary (GB) interactions. Two Σ11 asymmetrical tilt grain boundaries in Al are studied to explore the influence of orientation relationship and interface structure on dislocation activities at grain boundaries. To mimic the reality of a dislocation pileup in a coarse-grained polycrystalline, we optimized the dislocation population in MD simulations and developed a predict-correct method to create a dislocation pileup in MD simulations. MD simulations explored several kinetic processes of dislocations–GB reactions: grain boundary sliding, grain boundary migration, slip transmission, dislocation reflection, reconstruction of grain boundary, and the correlation of these kinetic processes with the available slip systems across the GB and atomic structures of the GB.

  17. Observing and modeling Earths energy flows

    SciTech Connect

    Stevens B.; Schwartz S.

    2012-05-11

    This article reviews, from the authors perspective, progress in observing and modeling energy flows in Earth's climate system. Emphasis is placed on the state of understanding of Earth's energy flows and their susceptibility to perturbations, with particular emphasis on the roles of clouds and aerosols. More accurate measurements of the total solar irradiance and the rate of change of ocean enthalpy help constrain individual components of the energy budget at the top of the atmosphere to within {+-}2 W m{sup -2}. The measurements demonstrate that Earth reflects substantially less solar radiation and emits more terrestrial radiation than was believed even a decade ago. Active remote sensing is helping to constrain the surface energy budget, but new estimates of downwelling surface irradiance that benefit from such methods are proving difficult to reconcile with existing precipitation climatologies. Overall, the energy budget at the surface is much more uncertain than at the top of the atmosphere. A decade of high-precision measurements of the energy budget at the top of the atmosphere is providing new opportunities to track Earth's energy flows on timescales ranging from days to years, and at very high spatial resolution. The measurements show that the principal limitation in the estimate of secular trends now lies in the natural variability of the Earth system itself. The forcing-feedback-response framework, which has developed to understand how changes in Earth's energy flows affect surface temperature, is reviewed in light of recent work that shows fast responses (adjustments) of the system are central to the definition of the effective forcing that results from a change in atmospheric composition. In many cases, the adjustment, rather than the characterization of the compositional perturbation (associated, for instance, with changing greenhouse gas concentrations, or aerosol burdens), limits accurate determination of the radiative forcing. Changes in clouds

  18. Absorbing boundary conditions for relativistic quantum mechanics equations

    SciTech Connect

    Antoine, X.; Sater, J.; Fillion-Gourdeau, F.; Bandrauk, A.D.

    2014-11-15

    This paper is devoted to the derivation of absorbing boundary conditions for the Klein–Gordon and Dirac equations modeling quantum and relativistic particles subject to classical electromagnetic fields. Microlocal analysis is the main ingredient in the derivation of these boundary conditions, which are obtained in the form of pseudo-differential equations. Basic numerical schemes are derived and analyzed to illustrate the accuracy of the derived boundary conditions.

  19. Grain boundary energy in 5 degrees of freedom space

    Energy Science and Technology Software Center

    2012-09-21

    GB5DOF is a program written in MatLab for computing excess energy of an arbitrary grain boundary defined by its 5 geometrical degrees of freedom. The program is written in the form of a single self-contained function callable from within commercially available MatLab software package. The function takes a geometric description of the boundary and material identity as input parameters and returns the predicted boundary energy.

  20. ARM - PI Product - Planetary Boundary Layer from AERI and MPL

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    ProductsPlanetary Boundary Layer from AERI and MPL ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send PI Product : Planetary Boundary Layer from AERI and MPL The distribution and transport of aerosol emitted to the lower troposphere is governed by the height of the planetary boundary layer (PBL), which limits the dilution of pollutants and influences boundary-layer convection. Because radiative heating and cooling of

  1. Two-dimensional heavy fermions on the strongly correlated boundaries...

    Office of Scientific and Technical Information (OSTI)

    Two-dimensional heavy fermions on the strongly correlated boundaries of Kondo topological insulators Prev Next Title: Two-dimensional heavy fermions on the strongly ...

  2. ARM - Field Campaign - 2013 Lower Atmospheric Boundary Layer...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Lower Atmospheric Boundary Layer Experiment 2012.09.17, Turner, SGP Comments? We would ... Lead Scientist : David Turner For data sets, see below. Abstract Instruments were deployed ...

  3. On the interaction of solutes with grain boundaries (Journal...

    Office of Scientific and Technical Information (OSTI)

    is considered by modeling solute atoms as misfitting inclusions within a disclination structural unit model describing the grain boundary structure and its intrinsic stress field. ...

  4. Influence of point defects on grain boundary diffusion in oxides

    SciTech Connect

    Stubican, V.S.

    1991-03-15

    The influence of point defects on grain boundary diffusion of Co ions in NiO was studied using polycrystalline films and bicrystals. Grain boundary diffusion was studied at 750 C at oxygen partial pressure. Two diffusion regions were found. At low oxygen pressures, extrinsic diffusion was observed. Above oxygen pressure of 10{sup {minus}7}, influence of intrinsic point defects was detected. It was determined that grain boundary diffusion was > 3 orders of magnitude faster than volume diffusion. However, it seems that grain boundary diffusion is influenced by the point defects in a similar way as the volume diffusion. 4 figs.

  5. Evaluation of Wall Boundary Condition Parameters for Gas-Solids

    Office of Scientific and Technical Information (OSTI)

    ... constitutive relations for antigranulocytes-materials, with application to plane shearing. ... Study of wall boundary condition in numerical simulations of 2D bubbling fluidized beds. ...

  6. "Lidar Investigations of Aerosol, Cloud, and Boundary Layer Properties...

    Office of Scientific and Technical Information (OSTI)

    Technical Report: "Lidar Investigations of Aerosol, Cloud, and Boundary Layer Properties Over the ARM ACRF Sites" Citation Details In-Document Search Title: "Lidar Investigations ...

  7. Joint retrievals of cloud and drizzle in marine boundary layer...

    Office of Scientific and Technical Information (OSTI)

    radar, lidar and zenith radiances Prev Next Title: Joint retrievals of cloud and drizzle in marine boundary layer clouds using ground-based radar, lidar and zenith ...

  8. [Perovskite and Fluorite Grain Boundary Properties]. Final Project Report

    SciTech Connect

    Browning, N. D.

    2004-02-24

    One of the main areas of research in the last two years in this program has been the properties of grain boundaries in perovskite and fluorite structure materials.

  9. Boundary condition and fuel composition effects on injection...

    Office of Scientific and Technical Information (OSTI)

    Publisher's Accepted Manuscript: Boundary condition and fuel composition effects on injection processes of high-pressure sprays at the microscopic level This content will become ...

  10. Planetary Boundary Layer from AERI and MPL (Dataset) | Data Explorer

    Office of Scientific and Technical Information (OSTI)

    Because radiative heating and cooling of the surface strongly affect the PBL top height, ... thus improve model parameterizations and our understanding of boundary-layer processes. ...

  11. Thermal benefits and cost effectiveness of earth berming

    SciTech Connect

    Speltz, J.; Haves, P.

    1980-01-01

    A number of advantages are claimed for earth sheltered buildings; the earth provides both insulation and thermal storage and also serves to reduce infiltration and noise. This paper seeks to quantify the thermal advantages of both earth sheltering and perimeter insulation by comparing the simulated thermal performance of an earth sheltered house, a house with perimeter insulation and a house with neither. The fuel savings are then compared to the estimated construction costs to determine cost-effectiveness. The major saving from an earth sheltered building is obtained in colder climates where the effective elevation of the frost line due to the earth berms considerably reduces the cost of the foundation.

  12. Earth Day, Every Day | National Nuclear Security Administration | (NNSA)

    National Nuclear Security Administration (NNSA)

    Earth Day, Every Day Monday, April 18, 2016 - 10:21am The 2016 theme for the Earth Day observance raises expectations for everyone: "Earth Day, Every Day." Instead of observing Earth Day only on April 22, the theme encourages us to think regularly about ways to save energy and live sustainably. As NNSA celebrates Earth Day this week, its leaders are demonstrating that NNSA is taking the 2016 Earth Day theme seriously. NNSA's Associate Administrator for Safety, Infrastructure and

  13. RACORO continental boundary layer cloud investigations. 3. Separation...

    Office of Scientific and Technical Information (OSTI)

    Brookhaven National Lab. (BNL), Upton, NY (United States) NASA Goddard Space Flight Center (GSFC), Greenbelt, MD (United States) UCLA Joint Institute for Regional Earth System ...

  14. Rare earths for life: an 85th birthday visit with Mr. Rare Earth...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Rare Earth While scientists often talk about their life's work, few lives have been fuller than that of Ames Laboratory's Karl A. Gschneidner, Jr. who's being honored for over...

  15. Applications of large-eddy simulation: Synthesis of neutral boundary layer models

    SciTech Connect

    Ohmstede, W.D.

    1987-12-01

    The object of this report is to describe progress made towards the application of large-eddy simulation (LES), in particular, to the study of the neutral boundary layer (NBL). The broad purpose of the study is to provide support to the LES project currently underway at LLNL. The specific purpose of this study is to lay the groundwork for the simulation of the SBL through the establishment and implementation of model criteria for the simulation of the NBL. The idealistic NBL is never observed in the atmosphere and therefore has little practical significance. However, it is of considerable theoretical interest for several reasons. The report discusses the concept of Rossby-number similarity theory as it applies to the NBL. A particular implementation of the concept is described. Then, the results from prior simulations of the NBL are summarized. Model design criteria for two versions of the Brost LES (BLES) model are discussed. The general guidelines for the development of Version 1 of the Brost model (BV1) were to implement the model with a minimum of modifications which would alter the design criteria as established by Brost. Two major modifications of BLES incorporated into BV1 pertain to the initialization/parameterization of the model and the generalization of the boundary conditions at the air/earth interface. 18 refs., 4 figs.

  16. The interstellar boundary explorer (IBEX): Update at the end of phase B

    SciTech Connect

    McComas, D. J.; Allegrini, F.; Pope, S.; Scherrer, J.; Bartolone, L.; Knappenberger, P.; Bochsler, P.; Wurz, P.; Bzowski, M.; Collier, M.; Moore, T.; Fahr, H.; Fichtner, H.; Frisch, P.; Funsten, H.; Fuselier, Steve; Gloeckler, G.; Gruntman, M.; Izmodenov, V.; Lee, M.

    2006-09-26

    The Interstellar Boundary Explorer (IBEX) mission will make the first global observations of the heliosphere's interaction with the interstellar medium. IBEX achieves these breakthrough observations by traveling outside of the Earth's magnetosphere in a highly elliptical orbit and taking global Energetic Neutral Atoms (ENA) images over energies from {approx}10 eV to 6 keV. IBEX's high-apogee ({approx}50 RE) orbit enables heliospheric ENA measurements by providing viewing from far above the Earth's relatively bright magnetospheric ENA emissions. This high energy orbit is achieved from a Pegasus XL launch vehicle by adding the propulsion from an IBEX-supplied solid rocket motor and the spacecraft's hydrazine propulsion system. IBEX carries two very large-aperture, single-pixel ENA cameras that view perpendicular to the spacecraft's Sun-pointed spin axis. Each six months, the continuous spinning of the spacecraft and periodic re-pointing to maintain the sun-pointing spin axis naturally lead to global, all-sky images. Over the course of our NASA Phase B program, the IBEX team optimized the designs of all subsystems. In this paper we summarize several significant advances in both IBEX sensors, our expected signal to noise (and background), and our groundbreaking approach to achieve a very high-altitude orbit from a Pegasus launch vehicle for the first time. IBEX is in full scale development and on track for launch in June of 2008.

  17. Guidelines for waste reduction and recycling: Metal finishing, electroplating, printed circuit board manufacturing

    SciTech Connect

    Not Available

    1989-07-01

    The guidance manual describes waste reduction techniques for metal finishing, metal fabricating, electroplating, and printed circuitboard manufacturing operations. Techniques which can be applied to a wide range of industrial processes and those which are process-specific are discussed. Evaporation, reverse osmosis, ion exchange, electrodialysis, ultrafiltration, and electrolytic recovery are described. The manual also describes waste reduction assessment procedures.

  18. 3D printed cellular solid outperforms traditional stochastic foam in long-term mechanical response

    DOE PAGES [OSTI]

    Maiti, A.; Small, W.; Lewicki, J.; Weisgraber, T. H.; Duoss, E. B.; Chinn, S. C.; Pearson, M. A.; Spadaccini, C. M.; Maxwell, R. S.; Wilson, T. S.

    2016-04-27

    3D printing of polymeric foams by direct-ink-write is a recent technological breakthrough that enables the creation of versatile compressible solids with programmable microstructure, customizable shapes, and tunable mechanical response including negative elastic modulus. However, in many applications the success of these 3D printed materials as a viable replacement for traditional stochastic foams critically depends on their mechanical performance and micro-architectural stability while deployed under long-term mechanical strain. To predict the long-term performance of the two types of foams we employed multi-year-long accelerated aging studies under compressive strain followed by a time-temperature-superposition analysis using a minimum-arc-length-based algorithm. The resulting master curvesmore » predict superior long-term performance of the 3D printed foam in terms of two different metrics, i.e., compression set and load retention. To gain deeper understanding, we imaged the microstructure of both foams using X-ray computed tomography, and performed finite-element analysis of the mechanical response within these microstructures. As a result, this indicates a wider stress variation in the stochastic foam with points of more extreme local stress as compared to the 3D printed material, which might explain the latter’s improved long-term stability and mechanical performance.« less

  19. Screen printed silver top electrode for efficient inverted organic solar cells

    SciTech Connect

    Kim, Junwoo; Duraisamy, Navaneethan; Lee, Taik-Min; Kim, Inyoung; Choi, Kyung-Hyun

    2015-10-15

    Highlights: • Screen printing of silver pattern. • X-ray diffraction pattern confirmed the face centered cubic structure of silver. • Uniform surface morphology of silver pattern with sheet resistance of 0.06 Ω/sq. • The power conversion efficiency of fabricated solar cell is found to be 2.58%. - Abstract: The present work is mainly focused on replacement of the vacuum process for top electrode fabrication in organic solar cells. Silver top electrode deposited through solution based screen printing on pre-deposited polymeric thin film. The solution based printing technology provides uniform top electrode without damaging the underlying organic layers. The surface crystallinity and surface morphology of silver top electrode are examined through X-ray diffraction, field-emission scanning electron microscope and atomic force microscope. The purity of silver is examined through X-ray energy dispersive spectroscopy. The top electrode exhibits face centered cubic structure with homogeneous morphology. The sheet resistance of top electrode is found to be 0.06 Ω/sq and an average pattern thickness of ∼15 μm. The power conversion efficiency is 2.58%. Our work demonstrates that the solution based screen printing is a significant role in the replacement of vacuum process for the fabrication of top electrode in organic solar cells.

  20. Assessing the operational life of flexible printed boards intended for continuous flexing applications : a case study.

    SciTech Connect

    Beck, David Franklin

    2011-01-01

    Through the vehicle of a case study, this paper describes in detail how the guidance found in the suite of IPC (Association Connecting Electronics Industries) publications can be applied to develop a high level of design assurance that flexible printed boards intended for continuous flexing applications will satisfy specified lifetime requirements.

  1. Recycling of rare earth metals from rare earth-transition metal alloy scrap by liquid metal extraction

    DOEpatents

    Ellis, T.W.; Schmidt, F.A.

    1995-08-01

    A method is described for treating rare earth metal-bearing scrap, waste or other material (e.g. Nd--Fe--B or Dy--Tb--Fe scrap) to recover the rare earth metal comprising melting the rare earth metal-bearing material, melting a Group IIA metal extractant, such as Mg, Ca, or Ba, in which the rare earth is soluble in the molten state, and contacting the melted material and melted extractant at a temperature and for a time effective to extract the rare earth from the melted material into the melted extractant. The rare earth metal is separated from the extractant metal by vacuum sublimation or distillation. 2 figs.

  2. Recycling of rare earth metals from rare earth-transition metal alloy scrap by liquid metal extraction

    DOEpatents

    Ellis, Timothy W.; Schmidt, Frederick A.

    1995-08-01

    Method of treating rare earth metal-bearing scrap, waste or other material (e.g. Nd--Fe--B or Dy--Tb--Fe scrap) to recover the rare earth metal comprising melting the rare earth metal-bearing material, melting a Group IIA metal extractant, such as Mg, Ca, or Ba, in which the rare earth is soluble in the molten state, and contacting the melted material and melted extractant at a temperature and for a time effective to extract the rare earth from the melted material into the melted extractant. The rare earth metal is separated from the extractant metal by vacuum sublimation or distillation.

  3. SUPERSONIC SHEAR INSTABILITIES IN ASTROPHYSICAL BOUNDARY LAYERS

    SciTech Connect

    Belyaev, Mikhail A.; Rafikov, Roman R., E-mail: rrr@astro.princeton.edu [Department of Astrophysical Sciences, Princeton University, Ivy Lane, Princeton, NJ 08540 (United States)

    2012-06-20

    Disk accretion onto weakly magnetized astrophysical objects often proceeds via a boundary layer (BL) that forms near the object's surface, in which the rotation speed of the accreted gas changes rapidly. Here, we study the initial stages of formation for such a BL around a white dwarf or a young star by examining the hydrodynamical shear instabilities that may initiate mixing and momentum transport between the two fluids of different densities moving supersonically with respect to each other. We find that an initially laminar BL is unstable to two different kinds of instabilities. One is an instability of a supersonic vortex sheet (implying a discontinuous initial profile of the angular speed of the gas) in the presence of gravity, which we find to have a growth rate of order (but less than) the orbital frequency. The other is a sonic instability of a finite width, supersonic shear layer, which is similar to the Papaloizou-Pringle instability. It has a growth rate proportional to the shear inside the transition layer, which is of order the orbital frequency times the ratio of stellar radius to the BL thickness. For a BL that is thin compared to the radius of the star, the shear rate is much larger than the orbital frequency. Thus, we conclude that sonic instabilities play a dominant role in the initial stages of nonmagnetic BL formation and give rise to very fast mixing between disk gas and stellar fluid in the supersonic regime.

  4. Irradiation Assisted Grain Boundary Segregation in Steels

    SciTech Connect

    Lu, Zheng; Faulkner, Roy G.

    2008-07-01

    The understanding of radiation-induced grain boundary segregation (RIS) has considerably improved over the past decade. New models have been introduced and much effort has been devoted to obtaining comprehensive information on segregation from the literature. Analytical techniques have also improved so that chemical analysis of layers 1 nm thick is almost routine. This invited paper will review the major methods used currently for RIS prediction: namely, Rate Theory, Inverse Kirkendall, and Solute Drag approaches. A summary is made of the available data on phosphorus RIS in reactor pressure vessel (RPV) steels. This will be discussed in the light of the predictions of the various models in an effort to show which models are the most reliable and easy to use for forecasting P segregation behaviour in steels. A consequence of RIS in RPV steels is a radiation induced shift in the ductile to brittle transition temperature (DBTT). It will be shown how it is possible to relate radiation-induced P segregation levels to DBTT shift. Examples of this exercise will be given for RPV steels and for ferritic steels being considered for first wall fusion applications. Cr RIS in high alloy stainless steels and associated irradiation-assisted stress corrosion cracking (IASCC) will be briefly discussed. (authors)

  5. Emerging Technologies in the Built Environment: Geographic Information Science (GIS), 3D Printing, and Additive Manufacturing

    SciTech Connect

    New, Joshua Ryan

    2014-01-01

    Abstract 1: Geographic information systems emerged as a computer application in the late 1960s, led in part by projects at ORNL. The concept of a GIS has shifted through time in response to new applications and new technologies, and is now part of a much larger world of geospatial technology. This presentation discusses the relationship of GIS and estimating hourly and seasonal energy consumption profiles in the building sector at spatial scales down to the individual parcel. The method combines annual building energy simulations for city-specific prototypical buildings and commonly available geospatial data in a GIS framework. Abstract 2: This presentation focuses on 3D printing technologies and how they have rapidly evolved over the past couple of years. At a basic level, 3D printing produces physical models quickly and easily from 3D CAD, BIM (Building Information Models), and other digital data. Many AEC firms have adopted 3D printing as part of commercial building design development and project delivery. This presentation includes an overview of 3D printing, discusses its current use in building design, and talks about its future in relation to the HVAC industry. Abstract 3: This presentation discusses additive manufacturing and how it is revolutionizing the design of commercial and residential facilities. Additive manufacturing utilizes a broad range of direct manufacturing technologies, including electron beam melting, ultrasonic, extrusion, and laser metal deposition for rapid prototyping. While there is some overlap with the 3D printing talk, this presentation focuses on the materials aspect of additive manufacturing and also some of the more advanced technologies involved with rapid prototyping. These technologies include design of carbon fiber composites, lightweight metals processing, transient field processing, and more.

  6. Aljazeera story on rare earths features Alex King | The Ames...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Aljazeera story on rare earths features Alex King Aljazeera America recently did a story on the demand and scarcity of rare-earth metals and spoke to Ames Laboratory scientist and...

  7. The Materials Preparation Center - Making Rare Earth Metals - Part 3

    ScienceCinema

    Riedemann, Trevor

    2013-03-01

    Trevor Riedeman, manager of the MPC Rare Earth Materials Section, gives a presentation on the importance of rare earth metals and how they are made at Ames Laboratory. Part 3 of 4.

  8. Preparations of rare earth-iron alloys by thermite reduction

    DOEpatents

    Schmidt, F.A.; Peterson, D.T.; Wheelock, J.T.

    1985-10-28

    Disclosed is an improved method for the preparation of high-purity rare earth-iron alloys by the aluminothermic reduction of a mixture of rare earth and iron fluorides.

  9. 2013 Community Earth System Model (CESM) Tutorial-Proposal to...

    Office of Scientific and Technical Information (OSTI)

    3 Community Earth System Model (CESM) Tutorial-Proposal to DOE Citation Details In-Document Search Title: 2013 Community Earth System Model (CESM) Tutorial-Proposal to DOE THE SAME ...

  10. The Materials Preparation Center - Making Rare Earth Metals - Part 4

    ScienceCinema

    Riedemann, Trevor

    2016-07-12

    Trevor Riedeman, manager of the MPC Rare Earth Materials Section, gives a presentation on the importance of rare earth metals and how they are made at Ames Laboratory. Part 4 of 4.

  11. The Materials Preparation Center - Making Rare Earth Metals - Part 1

    ScienceCinema

    Riedemann, Trevor

    2016-07-12

    Trevor Riedeman, manager of the MPC Rare Earth Materials Section, gives a presentation on the importance of rare earth metals and how they are made at Ames Laboratory. Part 1 of 4.

  12. Blue Earth-Nicollet-Faribault | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    Earth-Nicollet-Faribault Jump to: navigation, search Name: Blue Earth-Nicollet-Faribault Place: Minnesota Phone Number: 507-387-7963 Website: www.benco.org Facebook: https:...

  13. City of Blue Earth, Minnesota (Utility Company) | Open Energy...

    OpenEI (Open Energy Information) [EERE & EIA]

    Earth, Minnesota (Utility Company) Jump to: navigation, search Name: City of Blue Earth Place: Minnesota Phone Number: (507) 526-2191 or (507) 526-5382 or (507) 526-2402 Website:...

  14. Earth plus Mars: Los Alamos National Lab partners with Spain...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Earth plus Mars: Los Alamos National Lab partners with Spain and France Earth plus Mars: Los Alamos National Lab partners with Spain and France New Mexico's role in the next...

  15. What are the Rare Earths? | The Ames Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    What are the Rare Earths? Rare-earth metals or elements typically include scandium (Sc-21), yttrium (Y-39) and the lanthanides: lanthanum (La-57), cerium (Ce-58), praseodymium ...

  16. DOE-Led Research Team Makes Significant Rare Earth Discovery...

    Office of Environmental Management (EM)

    DOE-Led Research Team Makes Significant Rare Earth Discovery DOE-Led Research Team Makes ... Energy (DOE) has found that rare earth elements (REEs) can be removed from two U.S. ...

  17. Modeling Magnetism in Rare-Earth Intermetallic Materials | The...

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Modeling Magnetism in Rare-Earth Intermetallic Materials Theoretical modeling has led to a ... Rare-earth elements are unique in that their cores hold strongly localized electrons that ...

  18. BlueEarth Biofuels LLC | Open Energy Information

    OpenEI (Open Energy Information) [EERE & EIA]

    BlueEarth Biofuels LLC Jump to: navigation, search Name: BlueEarth Biofuels LLC Place: Hawaii Zip: 96813 Sector: Renewable Energy Product: Developer of power and renewable-energy...

  19. Proposal Title: Community Earth System Model (CESM) Tutorial

    Office of Scientific and Technical Information (OSTI)

    Proposal Title: Community Earth System Model (CESM) Tutorial PI: James W. Hurrell In fiscal year 2011, the Community Earth System Model (CESM) tutorial was taught at NCAR from 1-5 ...

  20. DOE Science Showcase - Rare Earth Metal Research from DOE Databases...

    Office of Scientific and Technical Information (OSTI)

    DOE Science Showcase - Rare Earth Metal Research from DOE Databases Information Bridge ... electrode in Ni-MH rechargeable cells Science.gov - H.R.4866 - Rare Earths Supply-Chain ...

  1. How Are You Celebrating Earth Day? | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    22, 2010 - 7:30am Addthis Happy Earth Day Today marks the 40th anniversary of celebrating Earth Day, and we hope you're getting into the spirit and committing to protecting the ...

  2. The integrated Earth System Model Version 1: formulation and...

    Office of Scientific and Technical Information (OSTI)

    Title: The integrated Earth System Model Version 1: formulation and functionality The integrated Earth System Model (iESM) has been developed as a new tool for pro- jecting the ...

  3. The Materials Preparation Center - Making Rare Earth Metals - Part 2

    ScienceCinema

    Riedemann, Trevor

    2013-03-01

    Trevor Riedeman, manager of the MPC Rare Earth Materials Section, gives a presentation on the importance of rare earth metals and how they are made at Ames Laboratory. Part 2 of 4.

  4. Ideas for What to Do this Earth Day

    Energy.gov [DOE]

    Given that Earth Day's coming up in a couple of days, you might find a few things you can do if you choose to celebrate Earth Day this year.

  5. Earth sheltered housing performance: a summary report

    SciTech Connect

    Boyer, L.L.; Grondzik, W.T.; Fitzgerald, D.K.

    1981-01-01

    Oklahoma and the surrounding interior plains region is being studied with respect to the extensive development of earth sheltered housing. An understanding of the occupant responses to this rediscovered dwelling concept is being determined through extended questionnaires and telephone interviews. Statistical evaluation of these responses should suggest regional relationships between the interior human environment and the exterior environment as expressed by earth sheltered architecture. Habitability and passive energy design are the main topics of interest being investigated at Oklahoma State University. Initial results indicate that occupants are generally satisfied with such attributes as structural safety, thermal comfort, and acoustic environment; but have some reservations concerning daylighting, site design, privacy of family members, and energy design and performance. Despite reservations on energy performance, owners have still achieved significant savings in comparison to their previous homes. A most promising fact is that these savings have been realized with little decrease and often an increase in comfort and habitability aspects.

  6. METHOD AND APPARATUS FOR EARTH PENETRATION

    DOEpatents

    Adams, W.M.

    1963-12-24

    A nuclear reactor apparatus for penetrating into the earth's crust is described. The apparatus comprises a cylindrical nuclear core operating at a temperature that is higher than the melting temperature of rock. A high-density ballast member is coupled to the nuclear core such that the overall density of the core-ballast assembly is greater than the density of molten rock. The nuclear core is thermally insulated so that its heat output is constrained to flow axially, with radial heat flow being minimized. In operation, the apparatus is placed in contact with the earth's crust at the point desired to be penetrated. The heat output of the reactor melts the underlying rock, and the apparatus sinks through the resulting magma. The fuel loading of the reactor core determines the ultimate depth of crust penetration. (AEC)

  7. Weather Research and Forecasting Model with the Immersed Boundary Method

    Energy Science and Technology Software Center

    2012-05-01

    The Weather Research and Forecasting (WRF) Model with the immersed boundary method is an extension of the open-source WRF Model available for wwww.wrf-model.org. The new code modifies the gridding procedure and boundary conditions in the WRF model to improve WRF's ability to simutate the atmosphere in environments with steep terrain and additionally at high-resolutions.

  8. Effects of tricritical points and morphotropic phase boundaries on the

    Office of Scientific and Technical Information (OSTI)

    piezoelectric properties of ferroelectrics (Journal Article) | DOE PAGES Effects of tricritical points and morphotropic phase boundaries on the piezoelectric properties of ferroelectrics Title: Effects of tricritical points and morphotropic phase boundaries on the piezoelectric properties of ferroelectrics Authors: Porta, Marcel ; Lookman, Turab Publication Date: 2011-05-13 OSTI Identifier: 1099369 Type: Publisher's Accepted Manuscript Journal Name: Physical Review B Additional Journal

  9. White Earth Nation Biomass Feasibility Study

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    March 27, 2014 Mike Triplett, Planner White Earth Nation Presentation Overview * Study Objectives * Accomplishments to Date * Initial Findings * Observations * Plans Forward 2 Study Objectives * Primary Objectives: * Conduct a due diligence grade feasibility study to assess the opportunity to convert existing thermal and power systems at the Shooting Star Casino to a sustainable bioenergy system. * Background * The Casino is utilizing fuel oil and propane fired boilers as primary source of

  10. rare earth recycling | Critical Materials Institute

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    recycling Electronic Waste: DOD is Recovering Materials but Several Factors May Hinder Near-Term Expansion of These Efforts File: Author: U.S. Government Accountability Office Publication Year: 2016 Read more about Electronic Waste: DOD is Recovering Materials but Several Factors May Hinder Near-Term Expansion of These Efforts Meet CMI Researcher David Reed CMI researcher David Reed is the principal investigator for the CMI project bioleaching for recovery of recycled rare earth elements. CMI

  11. White Earth Biomass/Biogas Feasibility Study

    SciTech Connect

    Triplett, Michael

    2015-03-12

    The White Earth Nation examined the feasibility of cost savings and fossil energy reduction through the installation of biogas/biomass boiler at the tribal casino. The study rejected biogas options due to availability and site constraints, but found a favorable environment for technical and financial feasibility of installing a 5 MMBtu hot water boiler system to offset 60-70 percent of current fuel oil and propane usage.

  12. Earth Sciences Division annual report 1980

    SciTech Connect

    Not Available

    1981-07-01

    Summaries of the highlights of programs in the Earth Sciences Division are presented under four headings; Geosciences, Geothermal Energy Development, Nuclear Waste Isolation, and Marine Sciences. Utilizing both basic and applied research in a wide spectrum of topics, these programs are providing results that will be of value in helping to secure the nation's energy future. Separate abstracts have been prepared for each project for inclusion in the Energy Data Base. (DMC)

  13. SEPARATION OF RARE EARTHS BY SOLVENT EXTRACTION

    DOEpatents

    Peppard, D.F.; Mason, G.W.

    1960-10-11

    A process is given for separating lanthanide rare earths from each other from an aqueous mineral acid solution, e.g., hydrochloric or nitric acid of a concentration of above 3 M, preferably 12 to 16 M, by extraction with a water- immiscible alkyl phosphate, such as tributyl phosphate or a mixture of mono-, di- and tributyl phosphate, and fractional back-extraction with mineral acid whereby the lanthanides are taken up by the acid in the order of increasing atomic number.

  14. Center for Space and Earth Science

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Institute of Geophysics, Planetary Physics, and Signatures Center for Space and Earth Science Promoting and supporting high-quality, cutting-edge science in the areas of astrophysics, space physics, solid planetary geoscience, and climate science. Contact Director Reiner Friedel (505) 665-1936 Email Professional Staff Assistant Georgia Sanchez (505) 665-0855 Email Astophysics and Cosmology Hui Li (505) 665-3131 Email Climate Keeley Costigan (505) 665-4788 Email Geophysics David Coblentz (505)

  15. Alkaline earth cation extraction from acid solution

    DOEpatents

    Dietz, Mark; Horwitz, E. Philip

    2003-01-01

    An extractant medium for extracting alkaline earth cations from an aqueous acidic sample solution is described as are a method and apparatus for using the same. The separation medium is free of diluent, free-flowing and particulate, and comprises a Crown ether that is a 4,4'(5')[C.sub.4 -C.sub.8 -alkylcyclohexano]18-Crown-6 dispersed on an inert substrate material.

  16. Earth Day Celebration at Nationals Park

    Energy.gov [DOE]

    As a part of the Earth Day celebration, Deputy Secretary Elizabeth Sherwood-Randall will represent DOE during the pregame acknowledgements and Presidents Race at Nationals Park on Friday, April 22, when the Nationals play the Minnesota Twins beginning at 7:05 p.m. The Sustainability Performance Office (SPO) is assisting with this "Celebration of Sustainability" to have some fun while promoting workplace sustainability to staff and citizens.

  17. Webtrends Archives by Fiscal Year — Earth Day

    Office of Energy Efficiency and Renewable Energy (EERE)

    From the EERE Web Statistics Archive: Corporate sites, Webtrends archives for the Earth Day site by fiscal year.

  18. New Rare Earth Element Extraction Technology | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Rare Earth Element Extraction Technology New Rare Earth Element Extraction Technology September 27, 2016 - 10:34am Addthis By looking at a problem at a nanoscale level, Pacific Northwest National Laboratory researchers are developing an economic way to extract valuable rare earth elements from geothermal fluids. This novel approach may help meet the high demand for rare earth elements that are used in many clean energy technologies. Watch our Energy 101 video to learn more about Geothermal

  19. The earth is in your hands

    SciTech Connect

    Browner, C.M.

    1995-08-01

    Earth Day 25 is a time to reflect on how mankind is doing in protecting their environment. Twenty-five years ago, in the wake of the first Earth Day, the US has created, virtually from scratch, the most advanced system of environmental protection in the world. In the course of a very short history--a mere quarter-century--man has made tremendous progress. Their skies and rivers are cleaner. And US environmental expertise and technology are in demand throughout the world. In the years since the first Earth Day, EPA banned lead in gasoline, lowering lead levels in the air by more than 90 percent and protecting millions of children from harm. Dangerous and widely used pesticides were banned. Unsafe local garbage dumps all over the nation were closed and recycling has become a household habit. American towns have been provided with substantial funding for wastewater treatment--the second biggest public works effort in US history, resulting in cleaner rivers all over the US. All cars and trucks now have standards for fuel economy, set by EPA, that allow consumers to choose a car for its energy efficiency. And EPA has played an important role in ensuring that companies and others comply with their environmental laws or face stiff penalties. Perhaps most important, the nation has gained a new understanding. More Americans than ever understand that to ensure a good quality of life they must act as responsible stewards of their air, their water, and their land.

  20. CADMIUM-RARE EARTH BORATE GLASS AS REACTOR CONTROL MATERIAL

    DOEpatents

    Ploetz, G.L.; Ray, W.E.

    1958-11-01

    A reactor control rod fabricated from a cadmiumrare earth-borate glass is presented. The rare earth component of this glass is selected from among those rare earths having large neutron capture cross sections, such as samarium, gadolinium or europium. Partlcles of this glass are then dispersed in a metal matrix by standard powder metallurgy techniques.

  1. The Ames Process for Rare Earth Metals | The Ames Laboratory

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    The Ames Process for Rare Earth Metals The Ames Process for the preparation of high purity rare earth metals (REM) is a descendent of the Ames Process for the preparation of uranium for the Manhattan Project - the metallothermic reduction of a metal-salt by an alkaline earth metal: 2RF3 + 3Ca -> 2R + 3CaF2 In this case the rare earth fluoride is reduced by calcium metal, resulting in the rare earth metal and a calcium fluoride slag. The fluoride input is prepared from high purity oxide via

  2. Note: Portable rare-earth element analyzer using pyroelectric crystal

    SciTech Connect

    Imashuku, Susumu Fuyuno, Naoto; Hanasaki, Kohei; Kawai, Jun

    2013-12-15

    We report a portable rare-earth element analyzer with a palm-top size chamber including the electron source of a pyroelectric crystal and the sample stage utilizing cathodoluminescence (CL) phenomenon. The portable rare-earth element analyzer utilizing CL phenomenon is the smallest reported so far. The portable rare-earth element analyzer detected the rare-earth elements Dy, Tb, Er, and Sm of ppm order in zircon, which were not detected by scanning electron microscopy-energy dispersive X-ray spectroscopy analysis. We also performed an elemental mapping of rare-earth elements by capturing a CL image using CCD camera.

  3. Efficient Earth-Sheltered Homes | Department of Energy

    Office of Energy Efficiency and Renewable Energy (EERE) (indexed site)

    Design » Types of Homes » Efficient Earth-Sheltered Homes Efficient Earth-Sheltered Homes This house in Tempe, Arizona, uses earth-sheltered construction methods to help decrease cooling costs. | Photo by Pamm McFadden This house in Tempe, Arizona, uses earth-sheltered construction methods to help decrease cooling costs. | Photo by Pamm McFadden If you are looking for a home with energy-efficient features that will provide a comfortable, tranquil, weather-resistant dwelling, an earth-sheltered

  4. (Environmental and geophysical modeling, fracture mechanics, and boundary element methods)

    SciTech Connect

    Gray, L.J.

    1990-11-09

    Technical discussions at the various sites visited centered on application of boundary integral methods for environmental modeling, seismic analysis, and computational fracture mechanics in composite and smart'' materials. The traveler also attended the International Association for Boundary Element Methods Conference at Rome, Italy. While many aspects of boundary element theory and applications were discussed in the papers, the dominant topic was the analysis and application of hypersingular equations. This has been the focus of recent work by the author, and thus the conference was highly relevant to research at ORNL.

  5. A Cartesian embedded boundary method for hyperbolic conservation laws

    SciTech Connect

    Sjogreen, B; Petersson, N A

    2006-12-04

    The authors develop an embedded boundary finite difference technique for solving the compressible two- or three-dimensional Euler equations in complex geometries on a Cartesian grid. The method is second order accurate with an explicit time step determined by the grid size away from the boundary. Slope limiters are used on the embedded boundary to avoid non-physical oscillations near shock waves. They show computed examples of supersonic flow past a cylinder and compare with results computed on a body fitted grid. Furthermore, they discuss the implementation of the method for thin geometries, and show computed examples of transonic flow past an airfoil.

  6. ARM - Field Campaign - Stable Boundary Layer Education (StaBLE)

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    govCampaignsStable Boundary Layer Education (StaBLE) Campaign Links Final Campaign Summary ARM Data Discovery Browse Data Comments? We would love to hear from you! Send us a note below or call us at 1-888-ARM-DATA. Send Campaign : Stable Boundary Layer Education (StaBLE) 2011.10.01 - 2014.05.31 Lead Scientist : David Turner For data sets, see below. Abstract The properties and processing in the nocturnal stable boundary layer are not well understood, which makes it difficult to represent

  7. Rare-Earth-Free Traction Motor: Rare Earth-Free Traction Motor for Electric Vehicle Applications

    SciTech Connect

    2012-01-01

    REACT Project: Baldor will develop a new type of traction motor with the potential to efficiently power future generations of EVs. Unlike todays large, bulky EV motors which use expensive, imported rare-earth-based magnets, Baldors motor could be light, compact, contain no rare earth materials, and have the potential to deliver more torque at a substantially lower cost. Key innovations in this project include the use of a unique motor design, incorporation of an improved cooling system, and the development of advanced materials manufacturing techniques. These innovations could significantly reduce the cost of an electric motor.

  8. Earth shelter performance and evaluation proceedings

    SciTech Connect

    Boyer, L.L. (ed.)

    1983-01-01

    Papers from 16 states, plus New South Wales, Australia, Alberta, Canada, and the Eastern Province of Saudi Arabia were presented in the conference. About one-third of the papers are authored by architects, nearly one-half by engineers, and the remainder are mainly by building contractors. Slightly over half of the authors are associated with universities, of which 13 are represented. The scale of the projects discussed varies from domestic, to commercial, to institutional; with an increased emphasis on passive solar inputs and earth cooling. Of the 32 papers presented, 19 were indexed separately for inclusion in the Energy Data Base. (JMT)

  9. An analysis of different insulation strategies for earth-sheltered buildings

    SciTech Connect

    Forowicz, T.Z. [Warsaw Univ. of Technology (Poland). Dept. of Architecture; [Polish Academy of Sciences, Warsaw (Poland). Inst. of Fundamental Technological Research; [Univ. of Colorado, Boulder, CO (United States). Joint Center for Energy Management

    1994-12-31

    This paper provides a comparative analysis of the energy performance of various insulation configurations for earth-sheltered buildings. It discusses the effectiveness of each insulation configuration in reducing the heating and cooling load. The long-term unsteady thermal processes between the building and the surrounding soil are considered. The mathematical model of the problem consists of a heat conduction equation with appropriate boundary and initial conditions. The variations in outside air temperature are driven by a harmonic function. The set of algebraic equations obtained by balancing the elementary heat flows into control elements is solved by an explicit scheme. The simulation program enables a two-dimensional thermal analysis in two cross sections for an underground building of any size situated at any depth. It predicts the heat flow between the building and the surrounding soil and through the ground`s surface. Internal building surface and soil temperatures are also calculated.

  10. VOLATILE TRANSPORT INSIDE SUPER-EARTHS BY ENTRAPMENT IN THE WATER-ICE MATRIX

    SciTech Connect

    Levi, A.; Podolak, M.; Sasselov, D.

    2013-05-20

    Whether volatiles can be entrapped in a background matrix composing planetary envelopes and be dragged via convection to the surface is a key question in understanding atmospheric fluxes, cycles, and composition. In this paper, we consider super-Earths with an extensive water mantle (i.e., water planets), and the possibility of entrapment of methane in their extensive water-ice envelopes. We adopt the theory developed by van der Waals and Platteeuw for modeling solid solutions, often used for modeling clathrate hydrates, and modify it in order to estimate the thermodynamic stability field of a new phase called methane filled ice Ih. We find that in comparison to water ice VII the filled ice Ih structure may be stable not only at the high pressures but also at the high temperatures expected at the core-water mantle transition boundary of water planets.

  11. Fabrication of contacts for silicon solar cells including printing burn through layers

    SciTech Connect

    Ginley, David S; Kaydanova, Tatiana; Miedaner, Alexander; Curtis, Calvin J; Van Hest, Marinus Franciscus Antonius Maria

    2014-06-24

    A method for fabricating a contact (240) for a solar cell (200). The method includes providing a solar cell substrate (210) with a surface that is covered or includes an antireflective coating (220). For example, the substrate (210) may be positioned adjacent or proximate to an outlet of an inkjet printer (712) or other deposition device. The method continues with forming a burn through layer (230) on the coating (220) by depositing a metal oxide precursor (e.g., using an inkjet or other non-contact printing method to print or apply a volume of liquid or solution containing the precursor). The method includes forming a contact layer (240) comprising silver over or on the burn through layer (230), and then annealing is performed to electrically connect the contact layer (240) to the surface of the solar cell substrate (210) through a portion of the burn through layer (230) and the coating (220).

  12. GraphPrints: Towards a Graph Analytic Method for Network Anomaly Detection

    SciTech Connect

    Harshaw, Chris R; Bridges, Robert A; Iannacone, Michael D; Reed, Joel W; Goodall, John R

    2016-01-01

    This paper introduces a novel graph-analytic approach for detecting anomalies in network flow data called \\textit{GraphPrints}. Building on foundational network-mining techniques, our method represents time slices of traffic as a graph, then counts graphlets\\textemdash small induced subgraphs that describe local topology. By performing outlier detection on the sequence of graphlet counts, anomalous intervals of traffic are identified, and furthermore, individual IPs experiencing abnormal behavior are singled-out. Initial testing of GraphPrints is performed on real network data with an implanted anomaly. Evaluation shows false positive rates bounded by 2.84\\% at the time-interval level, and 0.05\\% at the IP-level with 100\\% true positive rates at both.

  13. LLNL researchers outline what happens during metal 3D printing, enhancing

    National Nuclear Security Administration (NNSA)

    confidence | National Nuclear Security Administration | (NNSA) LLNL researchers outline what happens during metal 3D printing, enhancing confidence Friday, February 19, 2016 - 12:00am NNSA Blog From left, Lawrence Livermore National Laboratory researchers Ibo Matthews, a principal investigator leading the lab's effort on the joint open source software project; Wayne King, director of the Accelerated Certification of Additively Manufactured Metals Initiative; and Gabe Guss, engineering

  14. SU-C-213-06: Dosimetric Verification of 3D Printed Electron Bolus

    SciTech Connect

    Rasmussen, K; Corbett, M; Pelletier, C; Huang, Z; Feng, Y; Jung, J

    2015-06-15

    Purpose: To determine the dosimetric effect of 3D printed bolus in an anthropomorphic phantom. Methods: Conformable bolus material was generated for an anthropomorphic phantom from a DICOM volume. The bolus generated was a uniform expansion of 5mm applied to the nose region of the phantom, as this is a difficult area to uniformly apply bolus clinically. A Printrbot metal 3D Printer using PLA plastic generated the bolus. A 9MeV anterior beam with a 5cm cone was used to deliver dose to the nose of the phantom. TLD measurements were compared to predicted values at the phantom surface. Film planes were analyzed for the printed bolus, a standard 5mm bolus sheet placed on the phantom, and the phantom with no bolus applied to determine depth and dose distributions. Results: TLDs measured within 2.5% of predicted value for the 3D bolus. Film demonstrated a more uniform dose distribution in the nostril region for the 3d printed bolus than the standard bolus. This difference is caused by the air gap created around the nostrils by the standard bolus, creating a secondary build-up region. Both demonstrated a 50% central axis dose shift of 5mm relative to the no bolus film. HU for the bolus calculated the PLA electron density to be ∼1.1g/cc. Physical density was measured to be 1.3g/cc overall. Conclusion: 3D printed PLA bolus demonstrates improved dosimetric performance to standard bolus for electron beams with complex phantom geometry.

  15. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Sep 2016 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Hot Cell Complex - Building interfaces and cost optimization This document aims at specifying two transverse activities to be performed in parallel: 1 - Interfaces management: review of the input data for building design activities, elaboration of the Interfaces Sheets between the building (PBS62) and the systems, 2 - Cost optimization: continuous effort

  16. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    9 Sep 2016 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Technical Specifications_Engineering expertise for structural integrity This document describes technical needs on engineering structural integrity justification for diagnostic attachments to the ITER VV and Finite Element Analysis for the PPD Division. IDM UID TWU382 VERSION CREATED ON / VERSION / STATUS 28 Sep 2016 / 1.1 / Approved EXTERNAL REFERENCE

  17. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Oct 2016 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Technical_Specifications_Project, Integration of ITER Neutron Diagnostics This document describes technical needs of ITER/TED/PPD Diagnostics Division, with particular reference to engineering expertise for the Neutron Diagnostics project, integration and follow up activities, as appropriate. IDM UID TZV98M VERSION CREATED ON / VERSION / STATUS 17 Oct

  18. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    Oct 2016 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Summary Technical Specification - Metrology Equipment The purpose of this Call for Nomination (CFN) is to identify potential companies or consortia having the capacity to supply metrology equipment to be utilized in the Building 13 Metrology Laboratory and portable metrology instruments to be utilized during construction of the ITER Tokamak Machine and

  19. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    5 Sep 2016 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Technical summary for the supply and installation of a warehouse equipped with overhead crane This technical summary is prepared for the call for nomination of the supply and installation of a warehouse equipped with overhead crane. IDM UID THPYBL VERSION CREATED ON / VERSION / STATUS 15 Sep 2016 / 1.1 / Approved EXTERNAL REFERENCE / VERSION The supply

  20. DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM

    U.S. Department of Energy (DOE) - all webpages (Extended Search)

    6 Nov 2016 DISCLAIMER : UNCONTROLLED WHEN PRINTED - PLEASE CHECK THE STATUS OF THE DOCUMENT IN IDM Technical Specifications (In-Cash Procurement) Technical specification CATIA-ENOVIA QA and QC The present technical specification defines the needs of CIO/DO in CATIA/ENOVIA QA and QC tasks as well as in the implementation of DO processes such as CAD collaboration and Catalogues production IDM UID SWAFCG VERSION CREATED ON / VERSION / STATUS 02 Nov 2016 / 1.0 / Approved EXTERNAL REFERENCE / VERSION