March 2016 Most Viewed Documents for Materials

  1. The influence of grain size on the mechanical properties ofsteel
    Morris Jr., J.W. (2001)

    1234

  2. Fatigue design curves for 6061-T6 aluminum
    Yahr, G.T. (1993)

    981

  3. Heat Treatment Procedure Qualification -- Final Technical Report
    Robert C. Voigt (2004)

    946

  4. Charpy impact test results on five materials and NIST verification specimens using instrumented 2-mm and 8-mm strikers
    Nanstad, R.K.; Sokolov, M.A. (1995)

    855

  5. Mechanical properties and energy absorption characteristics of a polyurethane foam
    Goods, S.H.; Neuschwanger, C.L.; Henderson, C.; Skala, D.M. (1997)

    720

  6. Results of charpy V-notch impact testing of structural steel specimens irradiated at {approximately}30{degrees}C to 1 x 10{sup 16} neutrons/cm{sup 2} in a commercial reactor cavity
    Iskander, S.K.; Stoller, R.E. (1997)

    568

  7. Ferrite Measurement in Austenitic and Duplex Stainless Steel Castings - Literature Review
    Lundin, C.D.; Zhou, G.; Ruprecht, W. (1999)

    415

  8. Overcoming residual stresses and machining distortion in the production of aluminum alloy satellite boxes.
    Younger, Mandy S.; Eckelmeyer, Kenneth Hall (2007)

    352

  9. Work Functions of the transition Metals and Metal Silicides
    Drummond, T.J. (1999)

    287

  10. Verification of Allowable Stresses In ASME Section III Subsection NH For Grade 91 Steel & Alloy 800H
    R. W. Swindeman; M. J. Swindeman; B. W. Roberts; B. E. Thurgood; D. L. Marriott (2007)

    273

  11. Comparison of three Ni-Hard I alloys
    Dogan, Omer N.; Hawk, Jeffrey A.; Rice, J. (Texaloy Foundry Co., Inc., Floresville, Texas) (2004)

    259

  12. Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review
    Doebling, S.W.; Farrar, C.R.; Prime, M.B.; Shevitz, D.W. (1996)

    252

  13. A study of polyether-polyol- and polyester-polyol-based rigid urethane foam systems
    Madden, J.P.; Baker, G.K.; Smith, C.H. (1971)

    240

  14. Enhancing thermal conductivity of fluids with nanoparticles
    Choi, S.U.S.; Eastman, J.A. (1995)

    235

  15. Grain refinement of permanent mold cast copper base alloys. Final report
    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M. (2004)

    193

  16. PROPERTIES AND PERFORMANCE OF CEMENT-BASED GROUTS FOR GEOTHERMAL HEAT PUMP APPLICATIONS.
    ALLAN,M.L. (1999)

    156

  17. Corrosion Testing of Carbon Steel in Acid Cleaning Solutions
    Wiersma, B.J. (2002)

    154

  18. Optimization of Squeeze Casting for Aluminum Alloy Parts
    David Schwam; John F. Wallace; Qingming Chang; Yulong Zhu (2002)

    144

  19. Graphite design handbook
    Ho, F.H. (1988)

    143

  20. Yield improvement and defect reduction in steel casting
    Kent Carlson (2004)

    134