Abstract
Using high-energy irradiation initiation, isopropylacrylamide (IPAA) was grafted to a porous membrane dish composed of poly(ethylene terephthalate) (PET). IPPA demonstrates a transition from a hydrophobic to a hydrophilic structure with a simple change in temperature. The dishes were used for cell grow. Cells generally grow in an environment set at 37 deg. C, at which the IPAA polymer exhibits its hydrophobic structure. IPAA was attached uniformly to a cell culture surface, and cells were able to grow on top of the IPAA while it was in its hydrophobic state. Cells were easily removed from the surface of the dishes after changing the temperature below the LCST of IPAA. By changing the temperature polymer altered its structure to a hydrophilic state and no longer provided a suitable surface for the cells to adhere to. This caused the cells to lift off the culture surface without the use of a destructive enzyme such as trypsin or dispase. These cell sheets are useful to cell sheet engineering because the cells will retain both their extracellular matrix (ECM) and cell-to-cell junctions, which are normally lost in the harvest of cells. Poly(tetrafluoroethylene-co-hexefluoropropylene) (FEP) is a material under investigation as a polymer electrolyte membrane for fuel
More>>
Shahamat, L;
Al-Sheikhly, M
[1]
- Department of Materials Science and Engineering, College Park, MD (United States)
Citation Formats
Shahamat, L, and Al-Sheikhly, M.
Electron-Beam Induced Grafting of Isopropylacrylamide to a Poly(Ethylene-Terephthalate) Membrane for Cell Sheet Detachment, and Fuel Cell Membrane.
IAEA: N. p.,
2012.
Web.
Shahamat, L, & Al-Sheikhly, M.
Electron-Beam Induced Grafting of Isopropylacrylamide to a Poly(Ethylene-Terephthalate) Membrane for Cell Sheet Detachment, and Fuel Cell Membrane.
IAEA.
Shahamat, L, and Al-Sheikhly, M.
2012.
"Electron-Beam Induced Grafting of Isopropylacrylamide to a Poly(Ethylene-Terephthalate) Membrane for Cell Sheet Detachment, and Fuel Cell Membrane."
IAEA.
@misc{etde_22012235,
title = {Electron-Beam Induced Grafting of Isopropylacrylamide to a Poly(Ethylene-Terephthalate) Membrane for Cell Sheet Detachment, and Fuel Cell Membrane}
author = {Shahamat, L, and Al-Sheikhly, M}
abstractNote = {Using high-energy irradiation initiation, isopropylacrylamide (IPAA) was grafted to a porous membrane dish composed of poly(ethylene terephthalate) (PET). IPPA demonstrates a transition from a hydrophobic to a hydrophilic structure with a simple change in temperature. The dishes were used for cell grow. Cells generally grow in an environment set at 37 deg. C, at which the IPAA polymer exhibits its hydrophobic structure. IPAA was attached uniformly to a cell culture surface, and cells were able to grow on top of the IPAA while it was in its hydrophobic state. Cells were easily removed from the surface of the dishes after changing the temperature below the LCST of IPAA. By changing the temperature polymer altered its structure to a hydrophilic state and no longer provided a suitable surface for the cells to adhere to. This caused the cells to lift off the culture surface without the use of a destructive enzyme such as trypsin or dispase. These cell sheets are useful to cell sheet engineering because the cells will retain both their extracellular matrix (ECM) and cell-to-cell junctions, which are normally lost in the harvest of cells. Poly(tetrafluoroethylene-co-hexefluoropropylene) (FEP) is a material under investigation as a polymer electrolyte membrane for fuel cells. In order to make it ionically conductive, styrene was grafted to it and then subsequently sulfonated. Grafting of styrene to FEP was performed by simultaneous irradiation of the monomer and substrate to initiate the reaction, followed by a heat treatment to allow the reaction to undergo propagation. The effects of dose rate and heat treatment time on the weight percent yield of grafting and uniformity as a function of depth in the substrate was investigated. A 38.5 wt% graft was obtained after a 50 kGy dose of electron irradiation at a dose rate of 2,8 Gy/pulse and post-irradiation heat treatment of 60 deg. C for three hours. FTIR analysis of 10 {mu}m sections of material grafted under these conditions indicated that styrene had been grafted through the entire depth of the 125 {mu}m FEP substrate, as could be seen by the presence of bands at 2910, 2940, 1597, 1490 and 1444 cm{sup -1} which correspond to styrene. Additional characterization of the morphology and chemical composition of the material (on the surface and cross-section) was performed by atomic force microscopy (AFM), scanning electron microscopy (SEM), energy dispersive X ray spectroscopy (EDS), and X ray photoelectron spectroscopy (XPS). (author)}
place = {IAEA}
year = {2012}
month = {Sep}
}
title = {Electron-Beam Induced Grafting of Isopropylacrylamide to a Poly(Ethylene-Terephthalate) Membrane for Cell Sheet Detachment, and Fuel Cell Membrane}
author = {Shahamat, L, and Al-Sheikhly, M}
abstractNote = {Using high-energy irradiation initiation, isopropylacrylamide (IPAA) was grafted to a porous membrane dish composed of poly(ethylene terephthalate) (PET). IPPA demonstrates a transition from a hydrophobic to a hydrophilic structure with a simple change in temperature. The dishes were used for cell grow. Cells generally grow in an environment set at 37 deg. C, at which the IPAA polymer exhibits its hydrophobic structure. IPAA was attached uniformly to a cell culture surface, and cells were able to grow on top of the IPAA while it was in its hydrophobic state. Cells were easily removed from the surface of the dishes after changing the temperature below the LCST of IPAA. By changing the temperature polymer altered its structure to a hydrophilic state and no longer provided a suitable surface for the cells to adhere to. This caused the cells to lift off the culture surface without the use of a destructive enzyme such as trypsin or dispase. These cell sheets are useful to cell sheet engineering because the cells will retain both their extracellular matrix (ECM) and cell-to-cell junctions, which are normally lost in the harvest of cells. Poly(tetrafluoroethylene-co-hexefluoropropylene) (FEP) is a material under investigation as a polymer electrolyte membrane for fuel cells. In order to make it ionically conductive, styrene was grafted to it and then subsequently sulfonated. Grafting of styrene to FEP was performed by simultaneous irradiation of the monomer and substrate to initiate the reaction, followed by a heat treatment to allow the reaction to undergo propagation. The effects of dose rate and heat treatment time on the weight percent yield of grafting and uniformity as a function of depth in the substrate was investigated. A 38.5 wt% graft was obtained after a 50 kGy dose of electron irradiation at a dose rate of 2,8 Gy/pulse and post-irradiation heat treatment of 60 deg. C for three hours. FTIR analysis of 10 {mu}m sections of material grafted under these conditions indicated that styrene had been grafted through the entire depth of the 125 {mu}m FEP substrate, as could be seen by the presence of bands at 2910, 2940, 1597, 1490 and 1444 cm{sup -1} which correspond to styrene. Additional characterization of the morphology and chemical composition of the material (on the surface and cross-section) was performed by atomic force microscopy (AFM), scanning electron microscopy (SEM), energy dispersive X ray spectroscopy (EDS), and X ray photoelectron spectroscopy (XPS). (author)}
place = {IAEA}
year = {2012}
month = {Sep}
}