December 2016 Most Viewed Documents for Engineering

  1. Heat Treatment Procedure Qualification -- Final Technical Report
    Robert C. Voigt (2004)

    670

  2. Conduction heat transfer solutions
    VanSant, J.H. (1980)

    639

  3. Charpy impact test results on five materials and NIST verification specimens using instrumented 2-mm and 8-mm strikers
    Nanstad, R.K.; Sokolov, M.A. (1995)

    513

  4. Automotive vehicle sensors
    Sheen, S.H.; Raptis, A.C.; Moscynski, M.J. (1995)

    464

  5. Optimization of Operating Parameters for Minimum Mechanical Specific Energy in Drilling
    Hamrick, Todd [West Virginia Univ., Morgantown, WV (United States)] (2011)

    218

  6. Stress analysis and evaluation of a rectangular pressure vessel. [For equipment for sampling Hanford tank radwaste]
    Rezvani, M.A.; Ziada, H.H. (Westinghouse Hanford Co., Richland, WA (United States)); Shurrab, M.S. (Westinghouse Savannah River Co., Aiken, SC (United States)) (1992)

    217

  7. Heat transfer model of above and underground insulated piping systems
    Kwon, K.C. (1998)

    204

  8. Damage identification and health monitoring of structural and mechanical systems from changes in their vibration characteristics: A literature review
    Doebling, S.W.; Farrar, C.R.; Prime, M.B.; Shevitz, D.W. (1996)

    202

  9. Laser beam shaping techniques
    DICKEY,FRED M.; WEICHMAN,LOUIS S.; SHAGAM,RICHARD N. (2000)

    150

  10. An efficient method for calculating RMS von Mises stress in a random vibration environment
    Segalman, D.J.; Fulcher, C.W.G.; Reese, G.M.; Field, R.V. Jr. [Sandia National Labs., Albuquerque, NM (United States). Structural Dynamics and Vibration Control Dept.] (1998)

    145

  11. Failure Modes and Causes for Swing and Lift Type Check Valves.
    McElhaney, K.L. (1997)

    117

  12. Gating of Permanent Molds for Aluminum Casting
    David Schwam; John F. Wallace; Tom Engle; Qingming Chang (2004)

    110

  13. Wall thinning acceptance criteria for degraded carbon steel piping systems using FAD methodology
    Lam, P.S.; Gupta, N.K. (1995)

    102

  14. Work Functions of the transition Metals and Metal Silicides
    Drummond, T.J. (1999)

    101

  15. Electric motor model repair specifications
    NONE (1995)

    93

  16. Grain refinement of permanent mold cast copper base alloys. Final report
    Sadayappan, M.; Thomson, J. P.; Elboujdaini, M.; Gu, G. Ping; Sahoo, M. (2004)

    93

  17. SYNTHETIC SLING FAILURE - EVALUATIONS & RECOMMENDATIONS
    MACKEY TC; HENDERSON CS (2009)

    91

  18. Temperature effects and corrections in volume measurements based on liquid-level detection
    Suda, S.; Keisch, B. (1993)

    88

  19. Calibration interval technical basis document
    Chiaro, P.J. Jr. (1998)

    86

  20. Status on the Component Models Developed in the Modelica Framework: High-Temperature Steam Electrolysis Plant & Gas Turbine Power Plant
    Suk Kim, Jong [Idaho National Lab. (INL), Idaho Falls, ID (United States)]; McKellar, Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States)]; Bragg-Sitton, Shannon M. [Idaho National Lab. (INL), Idaho Falls, ID (United States)]; Boardman, Richard D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)] (2016)

    82

Last updated on Tuesday 17 January 2017