skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: EMPLACEMENT GANTRY ITS STANDARDS IDENTIFICATION STUDY

Abstract

To date, the project has established ITS performance requirements for SSCs based on identification and categorization of event sequences that may result in a radiological release. These performance requirements are defined within the NSDB. Further, SSCs credited with performing safe functions are classified as ITS. In turn, perform confirmation for these SSCs is sought through the use of consensus code and standards. The purpose of this study is to identify applicable codes and standards for the WP Emplacement Gantry ITS SSCs. Further, this study will form the basis for selection and the extent of applicability of each code and standard. This study is based on the design development completed for LA only. Accordingly, identification of ITS SSCs beyond those defined within the NSDB are based on designs that may be subject to further development during detail design. Furthermore, several design alternatives may still be under consideration to satisfy certain safety functions, and that final selection will not be determined until further design development has occurred. Therefore, for completeness, throughout this study alternative designs currently under considered will be discussed. Further, the results of this study will be subject to evaluation as part of a follow-on GAP analysis study. Based onmore » the results of this study the GAP analysis will evaluate each code and standard to ensure each ITS performance requirement is fully satisfied. When a performance requirement is not fully satisfied a ''gap'' is highlighted. Thereafter, the study will identify supplemental requirements to augment the code or standard to meet performance requirements. Further, the GAP analysis will identify non-standard areas of the design that will be subject to a Development Plan. Non-standard components and non-standard design configurations are defined as areas of the design that do not follow standard industry practices or codes and standards. Whereby, performance confirmation cannot be readily sought though use of consensus standards. The ITS codes and standards identified in this document were developed by the Yucca Mountain Project personnel from the Emplacement & Retrieval Project and are intended solely for the use of the Design and Engineering group in its work regarding the Emplacement and Retrieval system, specifically identification of Emplacement and Retrieval equipment codes and standards.« less

Authors:
Publication Date:
Research Org.:
Yucca Mountain Project, Las Vegas, Nevada
Sponsoring Org.:
USDOE
OSTI Identifier:
841264
Report Number(s):
800-30R-HE00-00200-000-00A
ENG.20050406.0015, DC#44727; TRN: US0600516
DOE Contract Number:  
AC28-01RW12101
Resource Type:
Technical Report
Country of Publication:
United States
Language:
English
Subject:
12 MANAGEMENT OF RADIOACTIVE WASTES, AND NON-RADIOACTIVE WASTES FROM NUCLEAR FACILITIES; DESIGN; EVALUATION; PERFORMANCE; PERSONNEL; POSITIONING; SAFETY; YUCCA MOUNTAIN

Citation Formats

M. Voegele. EMPLACEMENT GANTRY ITS STANDARDS IDENTIFICATION STUDY. United States: N. p., 2005. Web. doi:10.2172/841264.
M. Voegele. EMPLACEMENT GANTRY ITS STANDARDS IDENTIFICATION STUDY. United States. doi:10.2172/841264.
M. Voegele. Wed . "EMPLACEMENT GANTRY ITS STANDARDS IDENTIFICATION STUDY". United States. doi:10.2172/841264. https://www.osti.gov/servlets/purl/841264.
@article{osti_841264,
title = {EMPLACEMENT GANTRY ITS STANDARDS IDENTIFICATION STUDY},
author = {M. Voegele},
abstractNote = {To date, the project has established ITS performance requirements for SSCs based on identification and categorization of event sequences that may result in a radiological release. These performance requirements are defined within the NSDB. Further, SSCs credited with performing safe functions are classified as ITS. In turn, perform confirmation for these SSCs is sought through the use of consensus code and standards. The purpose of this study is to identify applicable codes and standards for the WP Emplacement Gantry ITS SSCs. Further, this study will form the basis for selection and the extent of applicability of each code and standard. This study is based on the design development completed for LA only. Accordingly, identification of ITS SSCs beyond those defined within the NSDB are based on designs that may be subject to further development during detail design. Furthermore, several design alternatives may still be under consideration to satisfy certain safety functions, and that final selection will not be determined until further design development has occurred. Therefore, for completeness, throughout this study alternative designs currently under considered will be discussed. Further, the results of this study will be subject to evaluation as part of a follow-on GAP analysis study. Based on the results of this study the GAP analysis will evaluate each code and standard to ensure each ITS performance requirement is fully satisfied. When a performance requirement is not fully satisfied a ''gap'' is highlighted. Thereafter, the study will identify supplemental requirements to augment the code or standard to meet performance requirements. Further, the GAP analysis will identify non-standard areas of the design that will be subject to a Development Plan. Non-standard components and non-standard design configurations are defined as areas of the design that do not follow standard industry practices or codes and standards. Whereby, performance confirmation cannot be readily sought though use of consensus standards. The ITS codes and standards identified in this document were developed by the Yucca Mountain Project personnel from the Emplacement & Retrieval Project and are intended solely for the use of the Design and Engineering group in its work regarding the Emplacement and Retrieval system, specifically identification of Emplacement and Retrieval equipment codes and standards.},
doi = {10.2172/841264},
journal = {},
number = ,
volume = ,
place = {United States},
year = {2005},
month = {4}
}