skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion

Abstract

The objective of this calculation is twofold. First, to determine whether or not separation of interlocking drip shield (DS) segments occurs during vibratory ground motion. Second, if DS separation does not occur, to estimate the area of the DS for which the residual 1st principal stress exceeds a certain limit. (The area of DS plate-1 and DS plate-2 [see Attachment I] where the residual 1st principal stress exceeds a certain limit will be, for brevity, referred to as ''the damaged area'' throughout this document; also, DS plate-1 and DS plate-2 will be referred to, for brevity, as ''DS plates'' henceforth.) The stress limit used throughout this document is defined as 50 percent of yield strength of the DS plate material, Titanium Grade 7 (Ti-7) (SB-265 R52400), at temperature of 150 C. A set of 15 calculations is performed at two different annual frequencies of occurrence (annual exceedance frequency): 10{sup -6} per year (1/yr) and 10{sup -7} 1/yr . (Note: Due to computational problems only five realizations at 10{sup -7} 1/yr are presented in this document.) Additionally, one calculation is performed at the annual frequency of occurrence of 5 {center_dot} 10{sup -4} 1/yr. The scope of this document is limited tomore » reporting whether or not the DS separation occurs. If the DS separation does not occur the scope is limited to reporting the calculation results in terms of the damaged area. All these results are evaluated for the DS plates. This calculation is intended for use in support of the Total System Performance Assessment-License Application seismicity modeling. This calculation is associated with the DS design and was performed by the Waste Package Design group. AP-3.12Q, ''Design Calculations and Analyses'' (Ref. 1) is used to perform the calculation and develop the document. The DS is classified as Quality Level 1 (Ref. 5, p. 7). Therefore, this calculation is subject to the Quality Assurance Requirements and Description (Ref. 4). The information provided by Attachment I is that of the potential design of the type of DS considered in this calculation, and provides the potential dimensions and materials for the DS design. Designs of the 21-PWR (Pressurized Water Reactor) waste package (WP) and emplacement pallet (pallet, for brevity, throughout the document) used in this calculation are those defined in References 24 and 22, respectively. All obtained results are valid for these designs only.« less

Authors:
Publication Date:
Research Org.:
Yucca Mountain Project, Las Vegas, NV (United States)
Sponsoring Org.:
US Department of Energy (US)
OSTI Identifier:
837517
Report Number(s):
000-00C-PEC0-00100-000-00A
ENG.20030618.0009, DC 36130; TRN: US200515%%402
Resource Type:
Technical Report
Resource Relation:
Other Information: PBD: 16 Jun 2003
Country of Publication:
United States
Language:
English
Subject:
36 MATERIALS SCIENCE; DESIGN; DIMENSIONS; GROUND MOTION; PERFORMANCE; PLATES; POSITIONING; QUALITY ASSURANCE; SEISMICITY; SHIELDS; SIMULATION; TITANIUM; WASTES; WATER; YIELD STRENGTH

Citation Formats

Mastilovic, S. Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion. United States: N. p., 2003. Web. doi:10.2172/837517.
Mastilovic, S. Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion. United States. https://doi.org/10.2172/837517
Mastilovic, S. 2003. "Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion". United States. https://doi.org/10.2172/837517. https://www.osti.gov/servlets/purl/837517.
@article{osti_837517,
title = {Structural Calculations of Drip Shield Exposed to Vibratory Ground Motion},
author = {Mastilovic, S},
abstractNote = {The objective of this calculation is twofold. First, to determine whether or not separation of interlocking drip shield (DS) segments occurs during vibratory ground motion. Second, if DS separation does not occur, to estimate the area of the DS for which the residual 1st principal stress exceeds a certain limit. (The area of DS plate-1 and DS plate-2 [see Attachment I] where the residual 1st principal stress exceeds a certain limit will be, for brevity, referred to as ''the damaged area'' throughout this document; also, DS plate-1 and DS plate-2 will be referred to, for brevity, as ''DS plates'' henceforth.) The stress limit used throughout this document is defined as 50 percent of yield strength of the DS plate material, Titanium Grade 7 (Ti-7) (SB-265 R52400), at temperature of 150 C. A set of 15 calculations is performed at two different annual frequencies of occurrence (annual exceedance frequency): 10{sup -6} per year (1/yr) and 10{sup -7} 1/yr . (Note: Due to computational problems only five realizations at 10{sup -7} 1/yr are presented in this document.) Additionally, one calculation is performed at the annual frequency of occurrence of 5 {center_dot} 10{sup -4} 1/yr. The scope of this document is limited to reporting whether or not the DS separation occurs. If the DS separation does not occur the scope is limited to reporting the calculation results in terms of the damaged area. All these results are evaluated for the DS plates. This calculation is intended for use in support of the Total System Performance Assessment-License Application seismicity modeling. This calculation is associated with the DS design and was performed by the Waste Package Design group. AP-3.12Q, ''Design Calculations and Analyses'' (Ref. 1) is used to perform the calculation and develop the document. The DS is classified as Quality Level 1 (Ref. 5, p. 7). Therefore, this calculation is subject to the Quality Assurance Requirements and Description (Ref. 4). The information provided by Attachment I is that of the potential design of the type of DS considered in this calculation, and provides the potential dimensions and materials for the DS design. Designs of the 21-PWR (Pressurized Water Reactor) waste package (WP) and emplacement pallet (pallet, for brevity, throughout the document) used in this calculation are those defined in References 24 and 22, respectively. All obtained results are valid for these designs only.},
doi = {10.2172/837517},
url = {https://www.osti.gov/biblio/837517}, journal = {},
number = ,
volume = ,
place = {United States},
year = {2003},
month = {6}
}