skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel

Abstract

In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr{sub 2}N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV{sub 0.025}. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.

Authors:
; ; ;  [1];  [2]
  1. Department of Metallurgical and Materials Engineering, Engineering Faculty, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey)
  2. Department of Metallurgical and Materials Engineering, Institute of Arts and Sciences, Sakarya University, Esentepe Campus, 54187 Sakarya (Turkey)
Publication Date:
OSTI Identifier:
22391301
Resource Type:
Journal Article
Resource Relation:
Journal Name: AIP Conference Proceedings; Journal Volume: 1653; Journal Issue: 1; Conference: APMAS 2014: 4. International Congress in Advances in Applied Physics and Materials Science, Fethiye (Turkey), 24-27 Apr 2014; Other Information: (c) 2015 AIP Publishing LLC; Country of input: International Atomic Energy Agency (IAEA)
Country of Publication:
United States
Language:
English
Subject:
36 MATERIALS SCIENCE; ALUMINIUM OXIDES; AMMONIUM CHLORIDES; CHROMIUM; CHROMIUM NITRIDES; COATINGS; DIFFUSION COATING; FRICTION FACTOR; HARDNESS; LAYERS; POWDERS; SCANNING ELECTRON MICROSCOPY; STEELS; WEAR; X-RAY DIFFRACTION

Citation Formats

Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr, Abakay, E., Sen, U., Sen, S., and Kilinc, B. Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel. United States: N. p., 2015. Web. doi:10.1063/1.4914225.
Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr, Abakay, E., Sen, U., Sen, S., & Kilinc, B. Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel. United States. doi:10.1063/1.4914225.
Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr, Abakay, E., Sen, U., Sen, S., and Kilinc, B. Mon . "Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel". United States. doi:10.1063/1.4914225.
@article{osti_22391301,
title = {Tribological properties of CrN coatings deposited by nitro-chromizing treatment on AISI D2 steel},
author = {Durmaz, M., E-mail: mdurmaz@sakarya.edu.tr and Abakay, E. and Sen, U. and Sen, S. and Kilinc, B.},
abstractNote = {In this work, the wear test of uncoated and chromium nitride coated AISI D2 cold work tool steel against alumina ball realized at 0.1 m/s sliding speeds and under the loads of 2.5N, 5N and 10N. Steel samples were nitrided at 575°C for 8 h in the first step of the coating process, and then chromium nitride coating was performed thermo-reactive deposition technique (TRD) in a powder mixture consisting of ferro-chromium, ammonium chloride and alumina at 1000°C for 2 h. Nitro-chromized samples were characterized by X-Ray diffraction analysis (XRD), scanning electron microscopy (SEM), micro-hardness and ball on disk wear tests. The coating layer formed on the AISI D2 steel was compact and homogeneous. X-ray studies showed that the phase formed in the coated layer is Cr{sub 2}N. The depth of the layer was 8.15 µm. The average hardness of the layer was 2160±15 HV{sub 0.025}. For uncoated and chromium nitride materials, wear rate increased with increasing load. The results of friction coefficient and wear rate of the tested materials showed that the CrN coating presents the lowest results.},
doi = {10.1063/1.4914225},
journal = {AIP Conference Proceedings},
number = 1,
volume = 1653,
place = {United States},
year = {Mon Mar 30 00:00:00 EDT 2015},
month = {Mon Mar 30 00:00:00 EDT 2015}
}