Thermal analytical study of polyamide copolymer/Surlyn Ionomers Blends

Title: Thermal analytical study of polyamide copolymer/Surlyn Ionomers Blends

Full Record
Other Related Research

Abstract

Thermal analytical technique was used as a screening method to study polyamide(Nylon)/ethylene-co-methacrylic acid copolymer-based ionomer(Surlyn)blends. The retardation of crystallization process from molten state of Nylon-12 by the existence of the ionomer was observed, but the crystallization of Nylon-12 can not be thwarted even at high concentration of ionomers. Zinc ionomers shows stronger effect than sodium ionomers. A Nylon copolymer, polyamide-6,6-co-polyamide-6,10, was used to blend with different ionomers and the crystallization process from molten state of Nylon copolymer could be thwarted at high concentration of zinc ionomer even at very cooling rate. Interesting cold crystallization behavior of polyamide copolymer was observed during second DSC heating cycle in the temperature range of the melting process of ionomer.

Authors:

Qin, C; Ding, Y P ^[1]

Baxter Healthcare Corp., Round Lake, IL (United States)

Publication Date:: 1993-12-31

OSTI Identifier:: 141942

Report Number(s):: CONF-930304-
TRN: 93:003688-1630

Resource Type:: Conference

Resource Relation:: Conference: 205. American Chemical Society national meeting, Denver, CO (United States), 28 Mar - 2 Apr 1993; Other Information: PBD: 1993; Related Information: Is Part Of 205th ACS national meeting; PB: 1951 p.

Country of Publication:: United States

Language:: English

Subject:: 36 MATERIALS SCIENCE; 40 CHEMISTRY; METHACRYLATES; COPOLYMERIZATION; COPOLYMERS; THERMAL ANALYSIS; CRYSTALLIZATION; NYLON

Citation Formats


                    Qin, C, and Ding, Y P. Thermal analytical study of polyamide copolymer/Surlyn Ionomers Blends.  United States: N. p., 1993. 
        Web.

Copy to clipboard


                    Qin, C, & Ding, Y P. Thermal analytical study of polyamide copolymer/Surlyn Ionomers Blends.  United States.

Copy to clipboard


                    Qin, C, and Ding, Y P. Fri .  
        "Thermal analytical study of polyamide copolymer/Surlyn Ionomers Blends".  United States.

Copy to clipboard


                    
@article{osti_141942,

  title        = {Thermal analytical study of polyamide copolymer/Surlyn Ionomers Blends},

  author       = {Qin, C and Ding, Y P},

  abstractNote = {Thermal analytical technique was used as a screening method to study polyamide(Nylon)/ethylene-co-methacrylic acid copolymer-based ionomer(Surlyn)blends. The retardation of crystallization process from molten state of Nylon-12 by the existence of the ionomer was observed, but the crystallization of Nylon-12 can not be thwarted even at high concentration of ionomers. Zinc ionomers shows stronger effect than sodium ionomers. A Nylon copolymer, polyamide-6,6-co-polyamide-6,10, was used to blend with different ionomers and the crystallization process from molten state of Nylon copolymer could be thwarted at high concentration of zinc ionomer even at very cooling rate. Interesting cold crystallization behavior of polyamide copolymer was observed during second DSC heating cycle in the temperature range of the melting process of ionomer.},

  doi          = {},

  url          = {https://www.osti.gov/biblio/141942},
  journal      = {},
number       = ,

  volume       = ,

  place        = {United States},

  year         = {1993},

  month        = {12}

}

Copy to clipboard

Conference:

Other availability

Please see Document Availability for additional information on obtaining the full-text document. Library patrons may search WorldCat to identify libraries that hold this conference proceeding.

Save / Share:

Export Metadata

Save to My Library

Similar records in OSTI.GOV collections:

Semicrystalline polyamide engineering thermoplastics based on the renewable monomer, 1,9-nonane diamine: Thermal properties and water absorption

Journal Article Kugel, Alex ; He, Jie ; Samanta, Satyabrata ; ... - Polymer-Plastics Technology and Engineering

Here, a series of poly(1,9-nonamethylene adipamide-co-1,9-nonamethylene terephthalamide) copolymers were produced using melt polymerization and the thermal properties, crystal structure, and moisture uptake characterized. The results confirmed that the copolymers exhibit isomorphism. As expected, glass transition temperature and the apparent melting temperature increased with increasing terephthalmide content. Using the difference in the apparent melting temperature to the crystallization temperature as a measure of relative crystallization rate, it was observed that crystallization rate decreased as the terephthalamide content of the copolymer was increased from 0 to 50 mole percent but then sharply increased when increased beyond 50 mole percent. This behavior maymore »« less
Cited by 6
https://doi.org/10.1080/03602559.2012.699576

Full Text Available
Investigation of the room temperature annealing peak in ionomers

Conference Goddard, R J ; Grady, B P ; Cooper, S L

A number of studies appearing in the literature have documented an endothermic peak in differential scanning calorimetry (DSC) scans for ethylene-methacrylic acid copolymer ionomers which appears only upon annealing at room temperature. This peak has been attributed to either polyethylene crystallites, ionic crystallite, or water absorption. In a novel polyurethane cationomer with a quarternized amine contained in hard segment, the same phenomena has been found in DSC scans when the neutralizing anion is bromine or iodine. Since this material does not crystallize, the authors were able to conclusively eliminate crystallization as the cause of the endotherm. The extended x-ray absorptionmore »« less
Compositions and extruded articles compromising polyolefin, polyamide and fatty acid amide

Patent Su, T K

This patent describes a film produced from a blend comprising at least 50 weight percent of a solid polymeric polyolefin selected from the group consisting of linear homopolymers of ethylene and of propylene and linear copolymers of ethylene and olefins of C/sub 4/ and higher. At least 5 weight percent of polymeric polyamide is selected from the class of polyamides known as nylons; and, N,N'-ethylene bis-oleamide fatty acid amide in an amount sufficient to increase the surface smoothness of an extrudate prepared from the same proportions of the polyolefin and the polyamide without the fatty acid amide.
The room temperature annealing peak in ionomers: Ionic crystallites or water absorption

Journal Article Goddard, R J ; Grady, B P ; Cooper, S L - Macromolecules; (United States)

A quaternized diol, 3-(trimethylammonio)-1,2-propanediol neutralized with either bromine or iodine, was used to produce a polyurethane cationomer with a poly(tetramethylene oxide) soft segment and a 4,4[prime]-diphenylmethane diisocyanate hard segment. If those cationomers were annealed at room temperature for a period of approximately 1 month in a desiccator filled with dry CaSO[sub 4], differential scanning calorimetry (DSC) studies showed an endotherm centered near 70 C which was not present in the unannealed polymer and did not reappear upon subsequent cooling and heating cycles in the DSC. Some authors have suggested that a very similar endotherm found in other ionomers, most notablymore »« less
https://doi.org/10.1021/ma00085a008
Morphological studies on block copolymer modified PA 6 blends

Journal Article Poindl, M., E-mail: marcus.poindl@ikt.uni-stuttgart.de, E-mail: christian.bonten@ikt.uni-stuttgart.de ; Bonten, C., E-mail: marcus.poindl@ikt.uni-stuttgart.de, E-mail: christian.bonten@ikt.uni-stuttgart.de - AIP Conference Proceedings

Recent studies show that compounding polyamide 6 (PA 6) with a PA 6 polyether block copolymers made by reaction injection molding (RIM) or continuous anionic polymerization in a reactive extrusion process (REX) result in blends with high impact strength and high stiffness compared to conventional rubber blends. In this paper, different high impact PA 6 blends were prepared using a twin screw extruder. The different impact modifiers were an ethylene propylene copolymer, a PA PA 6 polyether block copolymer made by reaction injection molding and one made by reactive extrusion. To ensure good particle matrix bonding, the ethylene propylene copolymermore »« less
https://doi.org/10.1063/1.4873864

Similar Records