Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline Ti using high energy X-ray diffraction microscopy

Wang, L.; Zheng, Z.; Phukan, H.; Kenesei, P.; Park, J. -S.; Lind, J P; Suter, Robert; Bieler, Thomas R.

doi:10.1016/j.actamat.2017.05.015

Title: Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline Ti using high energy X-ray diffraction microscopy

Journal Article · Sun May 07 00:00:00 EDT 2017 · Acta Materialia

DOI:https://doi.org/10.1016/j.actamat.2017.05.015· OSTI ID:1373591

Wang, L.; Zheng, Z.; Phukan, H.; Kenesei, P.; Park, J. -S.; Lind, J P; Suter, Robert; Bieler, Thomas R.

Knowledge of the critical resolved shear stress (CRSS) values of different slip modes is important for accurately modeling plastic deformation of hexagonal materials. Here, we demonstrate that CRSS can be directly measured with an in-situ high energy X-ray diffraction microscopy (HEDM) experiment. A commercially pure Ti tensile specimen was deformed up to 2.6% strain. In-situ far-field HEDM experiments were carried out to track the evolution of crystallographic orientations, centers of masses, and stress states of 1153 grains in a material volume of 1.1mm×1mm×1mm. Predominant prismatic slip was identified in 18 grains, where the orientation change occurred primarily by rotation around the c-axis during specimen deformation. By analyzing the resolved shear stress on individual slip systems, the estimated CRSS for prismatic slip is 96±18 MPa. Predominant basal slip was identified in 22 other grains, where the 2 orientation change occurred primarily by tilting the c-axis about an axis in the basal plane. The estimated CRSS for basal slip is 127±33 MPa. The ratio of CRSS_basal/CRSS_prismatic is in the range of 1.7-2.1. From indirect assessment, the CRSS for pyramidal < c+a > slip is likely greater than 240MPa. Lastly, grain size and free surface effects on the CRSS value in different grains are also examined.

View Accepted Manuscript (DOE)

View Accepted Manuscript (Publisher)

Cite

Export

Save

Research Organization:: Argonne National Laboratory (ANL), Argonne, IL (United States)

Sponsoring Organization:: USDOE Office of Science (SC), Basic Energy Sciences (BES)

Grant/Contract Number:: AC02-06CH11357; DESC0002001; AC52-07NA27344

OSTI ID:: 1373591

Alternate ID(s):: OSTI ID: 1397863

Journal Information:: Acta Materialia, Vol. 132, Issue C; ISSN 1359-6454

Publisher:: ElsevierCopyright Statement

Country of Publication:: United States

Language:: English

Citation Metrics:

Cited by: 107 works

Citation information provided by
Web of Science

References (44)

Modelling and prediction of mechanical properties for materials with hexagonal symmetry (zinc, titanium and zirconium alloys) Fundenberger, J. J.; Philippe, M. J.; Wagner, F. Acta Materialia, Vol. 45, Issue 10 https://doi.org/10.1016/S1359-6454(97)00099-2	journal	October 1997
Cyclic deformation behavior of high-purity titanium single crystals: Part II. Microstructure and mechanism Tan, X.; Guo, H.; Gu, H. Metallurgical and Materials Transactions A, Vol. 29, Issue 2 https://doi.org/10.1007/s11661-998-0132-z	journal	February 1998
Slip, twinning, and fracture in hexagonal close-packed metals Yoo, M. H. Metallurgical Transactions A, Vol. 12, Issue 3 https://doi.org/10.1007/BF02648537	journal	March 1981
Analysis of the different slip systems activated by tension in a α/β titanium alloy in relation with local crystallographic orientation Bridier, F.; Villechaise, P.; Mendez, J. Acta Materialia, Vol. 53, Issue 3 https://doi.org/10.1016/j.actamat.2004.09.040	journal	February 2005
Twin Nucleation by Slip Transfer across Grain Boundaries in Commercial Purity Titanium Wang, L.; Yang, Y.; Eisenlohr, P. Metallurgical and Materials Transactions A, Vol. 41, Issue 2 https://doi.org/10.1007/s11661-009-0097-6	journal	November 2009
A study of active deformation systems in titanium alloys: dependence on alloy composition and correlation with deformation texture Zaefferer, S. Materials Science and Engineering: A, Vol. 344, Issue 1-2 https://doi.org/10.1016/S0921-5093(02)00421-5	journal	March 2003
Methodology for estimating the critical resolved shear stress ratios of α-phase Ti using EBSD-based trace analysis Li, H.; Mason, D. E.; Bieler, T. R. Acta Materialia, Vol. 61, Issue 20 https://doi.org/10.1016/j.actamat.2013.08.042	journal	December 2013
In situ monitoring of the deformation mechanisms in titanium with different oxygen contents Barkia, B.; Doquet, V.; Couzinié, J. P. Materials Science and Engineering: A, Vol. 636 https://doi.org/10.1016/j.msea.2015.03.044	journal	June 2015
New opportunities for quantitative tracking of polycrystal responses in three dimensions Schuren, Jay C.; Shade, Paul A.; Bernier, Joel V. Current Opinion in Solid State and Materials Science, Vol. 19, Issue 4 https://doi.org/10.1016/j.cossms.2014.11.003	journal	August 2015
Strain hardening due to deformation twinning in α-titanium: Constitutive relations and crystal-plasticity modeling Salem, A. A.; Kalidindi, S. R.; Semiatin, S. L. Acta Materialia, Vol. 53, Issue 12 https://doi.org/10.1016/j.actamat.2005.04.014	journal	July 2005
Prediction of crystallographic texture evolution and anisotropic stress–strain curves during large plastic strains in high purity α-titanium using a Taylor-type crystal plasticity model Wu, X.; Kalidindi, S.; Necker, C. Acta Materialia, Vol. 55, Issue 2 https://doi.org/10.1016/j.actamat.2006.08.034	journal	January 2007
Experimental Characterization and Crystal Plasticity Modeling of Heterogeneous Deformation in Polycrystalline α-Ti Wang, L.; Barabash, R. I.; Yang, Y. Metallurgical and Materials Transactions A, Vol. 42, Issue 3 https://doi.org/10.1007/s11661-010-0249-8	journal	June 2010
Quantitative Atomic Force Microscopy Characterization and Crystal Plasticity Finite Element Modeling of Heterogeneous Deformation in Commercial Purity Titanium Yang, Y.; Wang, L.; Bieler, T. R. Metallurgical and Materials Transactions A, Vol. 42, Issue 3 https://doi.org/10.1007/s11661-010-0475-0	journal	December 2010
Lattice strain evolution during tensile and compressive loading of CP Ti Warwick, J. L. W.; Jones, N. G.; Rahman, K. M. Acta Materialia, Vol. 60, Issue 19 https://doi.org/10.1016/j.actamat.2012.08.042	journal	November 2012
Modeling bending of α-titanium with embedded polycrystal plasticity in implicit finite elements Knezevic, Marko; Lebensohn, Ricardo A.; Cazacu, Oana Materials Science and Engineering: A, Vol. 564 https://doi.org/10.1016/j.msea.2012.11.037	journal	March 2013
Experimental and theoretical studies of intergranular strain in an alpha titanium alloy during plastic deformation Gloaguen, D.; Oum, G.; Legrand, V. Acta Materialia, Vol. 61, Issue 15 https://doi.org/10.1016/j.actamat.2013.06.022	journal	September 2013
Micromechanical modeling of hardening mechanisms in commercially pure α-titanium in tensile condition Amouzou, K. E. K.; Richeton, T.; Roth, A. International Journal of Plasticity, Vol. 80 https://doi.org/10.1016/j.ijplas.2015.09.008	journal	May 2016
Anisotropy in the plastic flow properties of single-crystal α titanium determined from micro-cantilever beams Gong, Jicheng; Wilkinson, Angus J. Acta Materialia, Vol. 57, Issue 19 https://doi.org/10.1016/j.actamat.2009.07.064	journal	November 2009
Micro-cantilever testing of ⟨a⟩ prismatic slip in commercially pure Ti Gong, Jicheng; Wilkinson, Angus J. Philosophical Magazine, Vol. 91, Issue 7-9 https://doi.org/10.1080/14786435.2010.495359	journal	March 2011
Sample Dimensions Influence Strength and Crystal Plasticity Uchic, M. D. Science, Vol. 305, Issue 5686 https://doi.org/10.1126/science.1098993	journal	August 2004
Tracking: a method for structural characterization of grains in powders or polycrystals Lauridsen, E. M.; Schmidt, S.; Suter, R. M. Journal of Applied Crystallography, Vol. 34, Issue 6 https://doi.org/10.1107/S0021889801014170	journal	November 2001
Three-dimensional maps of grain boundaries and the stress state of individual grains in polycrystals and powders Poulsen, H. F.; Nielsen, S. F.; Lauridsen, E. M. Journal of Applied Crystallography, Vol. 34, Issue 6 https://doi.org/10.1107/S0021889801014273	journal	November 2001
An introduction to three-dimensional X-ray diffraction microscopy Poulsen, Henning Friis Journal of Applied Crystallography, Vol. 45, Issue 6, p. 1084-1097 https://doi.org/10.1107/S0021889812039143	journal	October 2012
Strain tensor development in a single grain in the bulk of a polycrystal under loading Margulies, L.; Lorentzen, T.; Poulsen, H. F. Acta Materialia, Vol. 50, Issue 7 https://doi.org/10.1016/S1359-6454(02)00028-9	journal	April 2002
Simultaneous measurement of the strain tensor of 10 individual grains embedded in an Al tensile sample Martins, René V.; Margulies, Lawrence; Schmidt, Søren Materials Science and Engineering: A, Vol. 387-389 https://doi.org/10.1016/j.msea.2004.02.069	journal	December 2004
Far-field high-energy diffraction microscopy: a tool for intergranular orientation and strain analysis Bernier, J. V.; Barton, N. R.; Lienert, U. The Journal of Strain Analysis for Engineering Design, Vol. 46, Issue 7 https://doi.org/10.1177/0309324711405761	journal	July 2011
Determining grain resolved stresses in polycrystalline materials using three-dimensional X-ray diffraction Oddershede, Jette; Schmidt, Søren; Poulsen, Henning Friis Journal of Applied Crystallography, Vol. 43, Issue 3 https://doi.org/10.1107/S0021889810012963	journal	April 2010
Measuring the stress field around an evolving crack in tensile deformed Mg AZ31 using three-dimensional X-ray diffraction Oddershede, Jette; Camin, Bettina; Schmidt, Søren Acta Materialia, Vol. 60, Issue 8 https://doi.org/10.1016/j.actamat.2012.02.054	journal	May 2012
Evolution of stress in individual grains and twins in a magnesium alloy aggregate Aydıner, C. C.; Bernier, J. V.; Clausen, B. Physical Review B, Vol. 80, Issue 2 https://doi.org/10.1103/PhysRevB.80.024113	journal	July 2009
In Situ Characterization of Twin Nucleation in Pure Ti Using 3D-XRD Bieler, Thomas R.; Wang, Leyun; Beaudoin, Armand J. Metallurgical and Materials Transactions A, Vol. 45, Issue 1 https://doi.org/10.1007/s11661-013-2082-3	journal	November 2013
Mechanical twinning and detwinning in pure Ti during loading and unloading – An in situ high-energy X-ray diffraction microscopy study Wang, L.; Lind, J.; Phukan, H. Scripta Materialia, Vol. 92 https://doi.org/10.1016/j.scriptamat.2014.08.008	journal	December 2014
On the deformation twinning of Mg AZ31B: A three-dimensional synchrotron X-ray diffraction experiment and crystal plasticity finite element model Abdolvand, Hamidreza; Majkut, Marta; Oddershede, Jette International Journal of Plasticity, Vol. 70 https://doi.org/10.1016/j.ijplas.2015.03.001	journal	July 2015
Study of 3-D stress development in parent and twin pairs of a hexagonal close-packed polycrystal: Part I – in-situ three-dimensional synchrotron X-ray diffraction measurement Abdolvand, Hamidreza; Majkut, Marta; Oddershede, Jette Acta Materialia, Vol. 93 https://doi.org/10.1016/j.actamat.2015.04.020	journal	July 2015
A framework for generating synthetic diffraction images from deforming polycrystals using crystal-based finite element formulations Wong, Su Leen; Park, Jun-Sang; Miller, Matthew P. Computational Materials Science, Vol. 77 https://doi.org/10.1016/j.commatsci.2013.03.019	journal	September 2013
Connecting heterogeneous single slip to diffraction peak evolution in high-energy monochromatic X-ray experiments Pagan, Darren C.; Miller, Matthew P. Journal of Applied Crystallography, Vol. 47, Issue 3 https://doi.org/10.1107/S1600576714005779	journal	May 2014
Slip systems and dislocation densities in individual grains of polycrystalline aggregates of plastically deformed CoTi and CoZr alloys Ungár, Tamás; Ribárik, Gábor; Zilahi, Gyula Acta Materialia, Vol. 71 https://doi.org/10.1016/j.actamat.2014.03.024	journal	June 2014
Deformation-induced orientation spread in individual bulk grains of an interstitial-free steel Oddershede, J.; Wright, J. P.; Beaudoin, A. Acta Materialia, Vol. 85 https://doi.org/10.1016/j.actamat.2014.11.038	journal	February 2015
High-energy diffraction microscopy at the advanced photon source Lienert, U.; Li, S. F.; Hefferan, C. M. JOM, Vol. 63, Issue 7 https://doi.org/10.1007/s11837-011-0116-0	journal	July 2011
GrainSpotter : a fast and robust polycrystalline indexing algorithm Schmidt, Søren Journal of Applied Crystallography, Vol. 47, Issue 1 https://doi.org/10.1107/S1600576713030185	journal	January 2014
Forward modeling method for microstructure reconstruction using x-ray diffraction microscopy: Single-crystal verification Suter, R. M.; Hennessy, D.; Xiao, C. Review of Scientific Instruments, Vol. 77, Issue 12 https://doi.org/10.1063/1.2400017	journal	December 2006
Adaptive reconstruction method for three-dimensional orientation imaging Li, S. F.; Suter, R. M. Journal of Applied Crystallography, Vol. 46, Issue 2 https://doi.org/10.1107/S0021889813005268	journal	March 2013
Tensile twin nucleation events coupled to neighboring slip observed in three dimensions Lind, J.; Li, S. F.; Pokharel, R. Acta Materialia, Vol. 76 https://doi.org/10.1016/j.actamat.2014.04.050	journal	September 2014
Slip band–grain boundary interactions in commercial-purity titanium Guo, Y.; Britton, T. B.; Wilkinson, A. J. Acta Materialia, Vol. 76 https://doi.org/10.1016/j.actamat.2014.05.015	journal	September 2014
A study of deformation twinning in a titanium alloy by X-ray diffraction contrast tomography Nervo, Laura; King, Andrew; Fitzner, Arnas Acta Materialia, Vol. 105 https://doi.org/10.1016/j.actamat.2015.12.032	journal	February 2016

Cited By (5)

Investigation of strain redistribution mechanism in α titanium by image-based crystal plasticity analysis Kawano, Yoshiki; Ohashi, Tetsuya; Mayama, Tsuyoshi The European Physical Journal B, Vol. 92, Issue 9 https://doi.org/10.1140/epjb/e2019-100238-3	journal	September 2019
A Planar Biaxial Experiment Platform for In Situ High-Energy Diffraction Studies Hommer, G. M.; Park, J. -S.; Brunson, Z. D. Experimental Mechanics, Vol. 59, Issue 5 https://doi.org/10.1007/s11340-019-00509-z	journal	May 2019
Heterogeneous Internal Strain Evolution in Commercial Purity Titanium Due to Anisotropic Coefficients of Thermal Expansion Zheng, Zebang; Eisenlohr, Philip; Bieler, T. R. JOM, Vol. 72, Issue 1 https://doi.org/10.1007/s11837-019-03743-x	journal	September 2019
Optimization of VPSC Model Parameters for Two-Phase Titanium Alloys: Flow Stress Vs Orientation Distribution Function Metrics Miller, V. M.; Semiatin, S. L.; Szczepanski, C. Metallurgical and Materials Transactions A, Vol. 49, Issue 8 https://doi.org/10.1007/s11661-018-4716-y	journal	June 2018
Combined Effects of Texture and Grain Size Distribution on the Tensile Behavior of α-Titanium Richeton, Thiebaud; Wagner, Francis; Chen, Cai Materials, Vol. 11, Issue 7 https://doi.org/10.3390/ma11071088	journal	June 2018

Similar Records

Study of slip activity in a Mg-Y alloy by in situ high energy X-ray diffraction microscopy and elastic viscoplastic self-consistent modeling

Journal Article · Thu May 31 00:00:00 EDT 2018 · Acta Materialia · OSTI ID:1373591

Wang, Leyun; Huang, Zhonghe; Wang, Huamiao; +6 more

Critical Shape for the Growth of Grain Boundary Twin Embryos in Mg and Mg Alloys: Crystal Plasticity Modeling

Journal Article · Mon Sep 05 00:00:00 EDT 2022 · Alloys · OSTI ID:1373591

Su, Yanqing; Arul Kumar, M.; Beyerlein, Irene J.

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Journal Article · Fri Mar 06 00:00:00 EST 2020 · Acta Materialia · OSTI ID:1373591

Zhang, Dingchang; Wang, Leyun; Zhang, Huan; +6 more

Related Subjects

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND TECHNOLOGY
Critical resolved shear stress
Crystal plasticity
High-energy X-ray diffraction
In situ tension test
Titanium

Title: Direct measurement of critical resolved shear stress of prismatic and basal slip in polycrystalline Ti using high energy X-ray diffraction microscopy

Citation Formats

References (44)

Cited By (5)

Similar Records

Related Subjects