skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Medium-temperature solid oxide fuel cells prepared using reactive magnetron sputtering. Ph.D. Thesis

Abstract

The purpose of this research is to investigate the deposition, structure, interfacial impedances, and characteristics of medium temperature solid-oxide fuel cells (SOFC`s) with thin-film electrolytes. Three main areas have been investigated. First, the structure, chemistry, and properties of materials designed specifically for medium temperature SOFC`s have been studied. The authors have developed techniques for sputter deposition of cubic 10 mol percent Y2O3-stabilized zirconia (YSZ) and 30 mol percent Y2O3-doped bismuth oxide (YSB) thin film oxygen ion conductors. The electrical properties of the films were characterized using the complex impedance spectroscopy method. Studies of AgYSZ cermet and Ag-perovskite (perovskite = La(1-x)Sr(x)Co(Mn)O3), used as high conductivity, low overpotential air electrodes, have also been carried out. Second, interfacial impedances for various electrode-electrolyte combinations and for multilayer electrolytes have been studied. In particular, the authors have found that a layer of Y-stabilized Bi2O3 (YSB) as thin as 60 nm between the YSZ electrolyte and the electrode significantly reduces the interfacial resistance. For example, inserting YSB between YSZ and a Ag-YSZ electrode reduces the resistance from 1.5 to 0.45 Omega cm(exp 2) at 750 deg C in air. Ag-(La,Sr)CoO3 on YSB electrolytes had interfacial resistances as low as 0.3 Omega cm2, compared with 0.4 andmore » 1.5 Omega cm(exp 2) for (La,Sr)CoO3 and Ag on YSB at 750 deg C, respectively. The Ag cermet materials thus exhibited lower interfacial resistances than their component materials. Third, thin film medium temperature SOFC`s have been fabricated and characterized. SOFC`s were deposited onto porous alumina supports. The resulting cell open-circuit voltages (OCV) were approximately equal to 0.8 V, 0.3 V less than expected, due to gas cross-over.« less

Authors:
Publication Date:
Research Org.:
Northwestern Univ., Evanston, IL (United States)
OSTI Identifier:
135414
Resource Type:
Miscellaneous
Resource Relation:
Other Information: TH: Ph.D. Thesis; PBD: 1993
Country of Publication:
United States
Language:
English
Subject:
30 DIRECT ENERGY CONVERSION; SOLID ELECTROLYTE FUEL CELLS; PERFORMANCE; ELECTROLYTES; DEPOSITION; INTERFACES; ELECTRIC IMPEDANCE; THIN FILMS; ELECTRIC CONDUCTIVITY

Citation Formats

Wang, L. Medium-temperature solid oxide fuel cells prepared using reactive magnetron sputtering. Ph.D. Thesis. United States: N. p., 1993. Web.
Wang, L. Medium-temperature solid oxide fuel cells prepared using reactive magnetron sputtering. Ph.D. Thesis. United States.
Wang, L. Fri . "Medium-temperature solid oxide fuel cells prepared using reactive magnetron sputtering. Ph.D. Thesis". United States.
@article{osti_135414,
title = {Medium-temperature solid oxide fuel cells prepared using reactive magnetron sputtering. Ph.D. Thesis},
author = {Wang, L},
abstractNote = {The purpose of this research is to investigate the deposition, structure, interfacial impedances, and characteristics of medium temperature solid-oxide fuel cells (SOFC`s) with thin-film electrolytes. Three main areas have been investigated. First, the structure, chemistry, and properties of materials designed specifically for medium temperature SOFC`s have been studied. The authors have developed techniques for sputter deposition of cubic 10 mol percent Y2O3-stabilized zirconia (YSZ) and 30 mol percent Y2O3-doped bismuth oxide (YSB) thin film oxygen ion conductors. The electrical properties of the films were characterized using the complex impedance spectroscopy method. Studies of AgYSZ cermet and Ag-perovskite (perovskite = La(1-x)Sr(x)Co(Mn)O3), used as high conductivity, low overpotential air electrodes, have also been carried out. Second, interfacial impedances for various electrode-electrolyte combinations and for multilayer electrolytes have been studied. In particular, the authors have found that a layer of Y-stabilized Bi2O3 (YSB) as thin as 60 nm between the YSZ electrolyte and the electrode significantly reduces the interfacial resistance. For example, inserting YSB between YSZ and a Ag-YSZ electrode reduces the resistance from 1.5 to 0.45 Omega cm(exp 2) at 750 deg C in air. Ag-(La,Sr)CoO3 on YSB electrolytes had interfacial resistances as low as 0.3 Omega cm2, compared with 0.4 and 1.5 Omega cm(exp 2) for (La,Sr)CoO3 and Ag on YSB at 750 deg C, respectively. The Ag cermet materials thus exhibited lower interfacial resistances than their component materials. Third, thin film medium temperature SOFC`s have been fabricated and characterized. SOFC`s were deposited onto porous alumina supports. The resulting cell open-circuit voltages (OCV) were approximately equal to 0.8 V, 0.3 V less than expected, due to gas cross-over.},
doi = {},
journal = {},
number = ,
volume = ,
place = {United States},
year = {1993},
month = {12}
}

Miscellaneous:
Other availability
Please see Document Availability for additional information on obtaining the full-text document. Library patrons may search WorldCat to identify libraries that may hold this item.

Save / Share: