skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Non-localized deformation in Cu Zr multi-layer amorphous films under tension

Authors:
; ; ; ; ; ; ;
Publication Date:
Sponsoring Org.:
USDOE Office of Fossil Energy (FE)
OSTI Identifier:
1344943
Grant/Contract Number:
FE-0008855; FE-0024054; FE-0011194; W911NF-13-1-0438
Resource Type:
Journal Article: Publisher's Accepted Manuscript
Journal Name:
Journal of Alloys and Compounds
Additional Journal Information:
Journal Volume: 678; Journal Issue: C; Related Information: CHORUS Timestamp: 2017-10-06 15:33:37; Journal ID: ISSN 0925-8388
Publisher:
Elsevier
Country of Publication:
Netherlands
Language:
English

Citation Formats

Zhong, C., Zhang, H., Cao, Q. P., Wang, X. D., Zhang, D. X., Hu, J. W., Liaw, P. K., and Jiang, J. Z. Non-localized deformation in Cu Zr multi-layer amorphous films under tension. Netherlands: N. p., 2016. Web. doi:10.1016/j.jallcom.2016.03.305.
Zhong, C., Zhang, H., Cao, Q. P., Wang, X. D., Zhang, D. X., Hu, J. W., Liaw, P. K., & Jiang, J. Z. Non-localized deformation in Cu Zr multi-layer amorphous films under tension. Netherlands. doi:10.1016/j.jallcom.2016.03.305.
Zhong, C., Zhang, H., Cao, Q. P., Wang, X. D., Zhang, D. X., Hu, J. W., Liaw, P. K., and Jiang, J. Z. 2016. "Non-localized deformation in Cu Zr multi-layer amorphous films under tension". Netherlands. doi:10.1016/j.jallcom.2016.03.305.
@article{osti_1344943,
title = {Non-localized deformation in Cu Zr multi-layer amorphous films under tension},
author = {Zhong, C. and Zhang, H. and Cao, Q. P. and Wang, X. D. and Zhang, D. X. and Hu, J. W. and Liaw, P. K. and Jiang, J. Z.},
abstractNote = {},
doi = {10.1016/j.jallcom.2016.03.305},
journal = {Journal of Alloys and Compounds},
number = C,
volume = 678,
place = {Netherlands},
year = 2016,
month = 9
}

Journal Article:
Free Publicly Available Full Text
Publisher's Version of Record at 10.1016/j.jallcom.2016.03.305

Citation Metrics:
Cited by: 3works
Citation information provided by
Web of Science

Save / Share:
  • Tensile tests were conducted on cylindrical rock specimens, cemented to end-caps attached to nontwist cables. In other tests, the rock specimens were bonded to platens cycled between tension and compression. The results indicated that the initial tangent modulus of rock is similar, both in uniaxial tension and in compression, but in tension the modulus decreases with increase of applied load; whereas, in compression, the modulus increases up to the stage of incipient failure. The value of the 50% modulus in compression is usually greater than the value in tension. At very low stresses, the Poisson ratio of rock in tensionmore » can be greater than 0.5, but after load cycling, the ratio is around or less than 0.1. (17 refs.)« less
  • A calculation and experimental procedure is suggested for evaluating the effect of the volumetric stressed state on yielding of metals. The main features of the effect of triaxial tension and test temperature on the yielding stress are demonstrated on the example of steel 45. It is established that triaxial tension under low temperature conditions may lead to a reduction in yield strength for the steel by 30%.
  • Shot-peening is a surface treatment for metals largely used to increase their fatigue resistance. According to some authors, shot-peening gives rise to residual compressive stress in the surface layers of the metals, which could explain the fatigue resistance improvement. This is quite reasonable as this compressive stress reduces the net effect of the tensile component of the applied cyclic loading. This effect increases the fatigue resistance. There is however another point of view on this subject that ascribes less importance to the residual compressive stress influence. It is based upon work which shows that cyclic loading promotes residual surface stressmore » modification by a mechanism of local plastic microdeformation. Since in this case a surface stress decrease would occur, these papers report that in the early applied cycles, residual stress could not have any influence on the ultimate fatigue behavior of the metal. This point of view highlights the need for a study to clarify the influence of plastic deformation upon relaxation as a function of variation of the initial surface residual stress. The aim of the present work is to provide a better understanding of these questions. Steel samples of 5Cr-0.5Mo (weight percent) were submitted to shot-penning in order to build up compressive surface residual stress. The samples were plastically deformed by uniaxial tensile test until complete fracture. Longitudinal and transverse residual stresses were measured before and during the test.« less
  • The objective of this study was to evaluate the rheological properties of polyethylene composites containing highly dispersed fillers such as carbon black and aerosil, under uniaxial tension. For comparison, the rheological properties under shear and their deformation strength in the solid state were evaluated.