skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: OTEC Cold Water Pipe-Platform Subsystem Dynamic Interaction Validation

Abstract

A commercial floating 100-megawatt (MW) ocean thermal energy conversion (OTEC) power plant will require a cold water pipe (CWP) with a diameter of 10-meter (m) and length of up to 1,000 m. The mass of the cold water pipe, including entrained water, can exceed the mass of the platform supporting it. The offshore industry uses software-modeling tools to develop platform and riser (pipe) designs to survive the offshore environment. These tools are typically validated by scale model tests in facilities able to replicate real at-sea meteorological and ocean (metocean) conditions to provide the understanding and confidence to proceed to final design and full-scale fabrication. However, today’s offshore platforms (similar to and usually larger than those needed for OTEC applications) incorporate risers (or pipes) with diameters well under one meter. Secondly, the preferred construction method for large diameter OTEC CWPs is the use of composite materials, primarily a form of fiber-reinforced plastic (FRP). The use of these material results in relatively low pipe stiffness and large strains compared to steel construction. These factors suggest the need for further validation of offshore industry software tools. The purpose of this project was to validate the ability to model numerically the dynamic interaction betweenmore » a large cold water-filled fiberglass pipe and a floating OTEC platform excited by metocean weather conditions using measurements from a scale model tested in an ocean basin test facility.« less

Authors:
 [1];  [2];  [3];  [4];  [5]
  1. Lockheed Martin Corporation, Manassas, VA (United States)
  2. John Halkyard and Associates, Houston, TX (United States)
  3. BMT Scientific Marine Services, Inc., Houston, TX (United States)
  4. Houston Offshore Engineering, Houston, TX (United States)
  5. Federal Univ. of Rio de Janeiro (Brazil). LabOceano
Publication Date:
Research Org.:
Lockheed Martin Corporation, Manassas, VA (United States)
Sponsoring Org.:
USDOE Office of Energy Efficiency and Renewable Energy (EERE), Wind and Water Technologies Office (EE-4W)
Contributing Org.:
John Halkyard and Associates, Houston, TX (United States); BMT Scientific Marine Services, Inc., Houston, TX (United States); Houston Offshore Engineering, Houston, TX (United States); Federal Univ. of Rio de Janeiro (Brazil). LabOceano
OSTI Identifier:
1326856
Report Number(s):
DE-EE0003637
DOE Contract Number:  
EE0003637
Resource Type:
Technical Report
Country of Publication:
United States
Language:
English
Subject:
13 HYDRO ENERGY; OTEC; Cold Water Pipe; Coupled Response; Model Basin

Citation Formats

Varley, Robert, Halkyard, John, Johnson, Peter, Shi, Shan, and Marinho, Thiago. OTEC Cold Water Pipe-Platform Subsystem Dynamic Interaction Validation. United States: N. p., 2014. Web. doi:10.2172/1326856.
Varley, Robert, Halkyard, John, Johnson, Peter, Shi, Shan, & Marinho, Thiago. OTEC Cold Water Pipe-Platform Subsystem Dynamic Interaction Validation. United States. https://doi.org/10.2172/1326856
Varley, Robert, Halkyard, John, Johnson, Peter, Shi, Shan, and Marinho, Thiago. 2014. "OTEC Cold Water Pipe-Platform Subsystem Dynamic Interaction Validation". United States. https://doi.org/10.2172/1326856. https://www.osti.gov/servlets/purl/1326856.
@article{osti_1326856,
title = {OTEC Cold Water Pipe-Platform Subsystem Dynamic Interaction Validation},
author = {Varley, Robert and Halkyard, John and Johnson, Peter and Shi, Shan and Marinho, Thiago},
abstractNote = {A commercial floating 100-megawatt (MW) ocean thermal energy conversion (OTEC) power plant will require a cold water pipe (CWP) with a diameter of 10-meter (m) and length of up to 1,000 m. The mass of the cold water pipe, including entrained water, can exceed the mass of the platform supporting it. The offshore industry uses software-modeling tools to develop platform and riser (pipe) designs to survive the offshore environment. These tools are typically validated by scale model tests in facilities able to replicate real at-sea meteorological and ocean (metocean) conditions to provide the understanding and confidence to proceed to final design and full-scale fabrication. However, today’s offshore platforms (similar to and usually larger than those needed for OTEC applications) incorporate risers (or pipes) with diameters well under one meter. Secondly, the preferred construction method for large diameter OTEC CWPs is the use of composite materials, primarily a form of fiber-reinforced plastic (FRP). The use of these material results in relatively low pipe stiffness and large strains compared to steel construction. These factors suggest the need for further validation of offshore industry software tools. The purpose of this project was to validate the ability to model numerically the dynamic interaction between a large cold water-filled fiberglass pipe and a floating OTEC platform excited by metocean weather conditions using measurements from a scale model tested in an ocean basin test facility.},
doi = {10.2172/1326856},
url = {https://www.osti.gov/biblio/1326856}, journal = {},
number = ,
volume = ,
place = {United States},
year = {Fri May 09 00:00:00 EDT 2014},
month = {Fri May 09 00:00:00 EDT 2014}
}