skip to main content
OSTI.GOV title logo U.S. Department of Energy
Office of Scientific and Technical Information

Title: Degradation of thermally-cured silicone encapsulant under terrestrial UV

Abstract

Concentrator photovoltaic (CPV) modules operate in extreme conditions, including enhanced solar flux, elevated operating temperature, and frequent thermal cycling. Coupled with active environmental species such as oxygen and moisture, the operating conditions pose a unique materials challenge for guaranteeing operational lifetimes of greater than 25 years. Specifically, the encapsulants used in the optical elements are susceptible to environmental degradation during operation. For example, the interfaces must remain in contact to prevent optical attenuation and thermal runaway. We developed fracture mechanics based metrologies to characterize the adhesion of the silicone encapsulant and its adjacent surfaces, as well as the cohesion of the encapsulant. Further, we studied the effects of weathering on adhesion using an outdoor concentrator operating in excess of 1100 times the AM1.5 direct irradiance and in indoor environmental chambers with broadband ultraviolet (UV) irradiation combined with controlled temperature and humidity. We observed a sharp initial increase in adhesion energy followed by a gradual decrease in adhesion as a result of both outdoor concentrator exposure and indoor UV weathering. We characterized changes in mechanical properties and chemical structures using XPS, FTIR, and DMA to understand the fundamental connection between mechanical strength and the degradation of the silicone encapsulant. We developedmore » physics based models to explain the change in adhesion and to predict operational lifetimes of the materials and their interfaces.« less

Authors:
; ; ;
Publication Date:
Research Org.:
National Renewable Energy Lab. (NREL), Golden, CO (United States)
Sponsoring Org.:
USDOE SunShot Initiative, Physics of Reliability: Evaluating Design Insights for Component Technologies in Solar (PREDICTS) Program
OSTI Identifier:
1273067
Report Number(s):
NREL/JA-5J00-66789
Journal ID: ISSN 0927-0248
DOE Contract Number:
AC36-08GO28308
Resource Type:
Journal Article
Resource Relation:
Journal Name: Solar Energy Materials and Solar Cells; Journal Volume: 157
Country of Publication:
United States
Language:
English
Subject:
14 SOLAR ENERGY; 36 MATERIALS SCIENCE; adhesion; reliability; silicone; UV degradation

Citation Formats

Cai, Can, Miller, David C., Tappan, Ian A., and Dauskardt, Reinhold H.. Degradation of thermally-cured silicone encapsulant under terrestrial UV. United States: N. p., 2016. Web. doi:10.1016/j.solmat.2016.05.065.
Cai, Can, Miller, David C., Tappan, Ian A., & Dauskardt, Reinhold H.. Degradation of thermally-cured silicone encapsulant under terrestrial UV. United States. doi:10.1016/j.solmat.2016.05.065.
Cai, Can, Miller, David C., Tappan, Ian A., and Dauskardt, Reinhold H.. Thu . "Degradation of thermally-cured silicone encapsulant under terrestrial UV". United States. doi:10.1016/j.solmat.2016.05.065.
@article{osti_1273067,
title = {Degradation of thermally-cured silicone encapsulant under terrestrial UV},
author = {Cai, Can and Miller, David C. and Tappan, Ian A. and Dauskardt, Reinhold H.},
abstractNote = {Concentrator photovoltaic (CPV) modules operate in extreme conditions, including enhanced solar flux, elevated operating temperature, and frequent thermal cycling. Coupled with active environmental species such as oxygen and moisture, the operating conditions pose a unique materials challenge for guaranteeing operational lifetimes of greater than 25 years. Specifically, the encapsulants used in the optical elements are susceptible to environmental degradation during operation. For example, the interfaces must remain in contact to prevent optical attenuation and thermal runaway. We developed fracture mechanics based metrologies to characterize the adhesion of the silicone encapsulant and its adjacent surfaces, as well as the cohesion of the encapsulant. Further, we studied the effects of weathering on adhesion using an outdoor concentrator operating in excess of 1100 times the AM1.5 direct irradiance and in indoor environmental chambers with broadband ultraviolet (UV) irradiation combined with controlled temperature and humidity. We observed a sharp initial increase in adhesion energy followed by a gradual decrease in adhesion as a result of both outdoor concentrator exposure and indoor UV weathering. We characterized changes in mechanical properties and chemical structures using XPS, FTIR, and DMA to understand the fundamental connection between mechanical strength and the degradation of the silicone encapsulant. We developed physics based models to explain the change in adhesion and to predict operational lifetimes of the materials and their interfaces.},
doi = {10.1016/j.solmat.2016.05.065},
journal = {Solar Energy Materials and Solar Cells},
number = ,
volume = 157,
place = {United States},
year = {Thu Dec 01 00:00:00 EST 2016},
month = {Thu Dec 01 00:00:00 EST 2016}
}
  • The aging of a commercial filled siloxane polymeric composite in states of high stress and Co-60 {gamma}-radiation exposure has been studied. DC-745 is a commercially available silicone elastomer consisting of dimethyl, methyl-phenyl, and vinyl-methyl siloxane monomers crosslinked with a peroxide vinyl specific curing agent. It is filled with {approx}30 wt.% mixture of high and low surface area silicas. This filled material is shown to be subject to permanent set if exposed to radiation while under tensile stress. Tensile modulus measurements show that the material gets marginally softer with combined radiation exposure and tensile strain as compared to material exposed tomore » radiation without tensile strain. In addition, the segmental dynamics as measured by both uniaxial NMR relaxometry and Multiple Quantum NMR methods indicate that the material is undergoes radiatively-induced crosslinking in the absence of tensile strain and a combination of crosslinking and strain dependent increase in dynamic order parameter for the network chains. The MQ-NMR also suggests a small change in the number of polymer chains associated with the silica filler surface. Comparison of the prediction of the relative change in crosslink density from the NMR data as well as solvent swelling data and from that predicted from the Tobolsky model suggest that degradation leads to a deviation from Gaussian chain statistics and the formation of increased numbers of elastically ineffective network chains.« less
  • Sn-doped and undoped nano-TiO{sub 2} particles have been synthesized by hydrotermal process without acid catalyst at 225 deg. C in 1 h. Nanostructure-TiO{sub 2} based thin films, contain at different solid ratio of TiO{sub 2} in coating, have been prepared on glass surfaces by spin-coating technique. The structure, surface morphology and optical properties of the thin films and the particles have been investigated by element analysis and XRD, BET and UV/VIS/NIR techniques. The photocatalytic performance of the films was tested for degradation of malachite green dye in solution under UV and VIS-lights. The results showed that the hydrothermally synthesized nano-TiO{submore » 2} particles are fully anatase crystalline form and are easily dispersed in water, the coated surfaces have nearly super-hydrophilic properties and, the doping of transition metal ion efficiently improved the photocatalytic performance of the TiO{sub 2} thin film. The results also proved that malachite green is decomposed catalytically due to the pseudo first-order reaction kinetics.« less
  • Highlights: • Excellent photocatalyst was obtained by introducing BiOCl–TiO{sub 2} onto attapulgite. • 100 mg L{sup −1} methyl orange (MO) was totally decomposed under UV light within 70 min. • 92.6% of 10 mg L{sup −1} MO was decomposed within 120 min under visible light. • ATT–BiOCl–TiO{sub 2} show better activity than P{sub 25} especially under visible light. • Mechanism of photocatalytic activity enhancement was identified. - Abstract: An environmental friendly composite photocatalyst with efficient UV and visible light activity has been synthesized by introducing BiOCl–TiO{sub 2} hybrid oxide onto the surface of attapulgite (ATT) (denoted as ATT–BiOCl–TiO{sub 2}), usingmore » a simple in situ depositing technique. The obtained products were characterized by XRD, TEM, BET and UV–vis diffuse reflectance spectra measurements. Results showed that BiOCl–TiO{sub 2} composite particles were successfully loaded onto attapulgite fibers' surface without obvious aggregation. The photocatalytic activity of ATT–BiOCl–TiO{sub 2} was investigated by degradation of methyl orange under UV and visible light irradiation. It was found that 100 mg L{sup −1} methyl orange was totally decomposed under UV light within 70 min and 92.57% of 10 mg L{sup −1} methyl orange was decomposed under visible light within 120 min using ATT–BiOCl–TiO{sub 2} as photocatalyst. These results were quite better than that of P{sub 25}, especially under visible light irradiation. Possible mechanism for the enhancement was proposed.« less
  • Acrylic films have been prepared by photopolymerization of mixtures of an epoxyacrylic resin with linear chain acrylic monomers having the structure H-(CH{sub 2}){sub n}-O-CO-CH {double_bond} CH{sub 2} with n ranging from 4 to 18. The resins were cast on a glass slide and cured in an inert atmosphere; their surface properties were investigated by advancing and receding contact angles and surface tension measurements according to the Zisman method. The pure resin film showed the same surface properties on both sides, that exposed to the atmosphere and that in contact with the substrate. Addition of the acrylic monomers caused an asymmetricmore » distribution of them on the two sides of the film, depending on the alkylic chain length and on the acrylic monomer concentration. The asymmetry of the film was confirmed by XPS analysis that pointed out a significant enrichment of the apolar monomer on the air side. The surface properties were correlated to the monomer polarity (ruled by its hydrocarbon chain length). The contact angle hysteresis provided insight into the heterogeneity and the roughness of the polymeric surface.« less