Control Dewar and VLPC Bayonet Can Platform Connection Design and Analysis

doi:https://doi.org/10.2172/1032129

Title: Control Dewar and VLPC Bayonet Can Platform Connection Design and Analysis

Full Record
Other Related Research

Abstract

The four connections for the control dewar and VLPC bayonet can platform are designed, using finite element analysis, to carry all dead weight and live loads. Based on the loads applied to the platform, two 1 inch thick plates and two 3/4 inch thick brackets made of ASTM A572-Grade 42 are required. The 1 inch thick plate requires a 3/8 inch thick intermediate steel material, between the 8-inch x 4-inch x 1/4-inch boom and the plate, for load reinforcement as well as weld area reinforcement. Both the plates and the brackets require 3/4 inch steel bolt connections.

Authors:: Kuwazaki, A.

Publication Date:: 1997-07-29

Research Org.:: Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

Sponsoring Org.:: USDOE Office of Science (SC)

OSTI Identifier:: 1032129

Report Number(s):: FERMILAB-D0-EN-467
TRN: US1200494

DOE Contract Number:: AC02-07CH11359

Resource Type:: Technical Report

Country of Publication:: United States

Language:: English

Subject:: 43 PARTICLE ACCELERATORS; DESIGN; DEWARS; FASTENERS; PLATES; STEELS; Experiment-HEP

Citation Formats


                    Kuwazaki, A., and /Fermilab. Control Dewar and VLPC Bayonet Can Platform Connection Design and Analysis.  United States: N. p., 1997. 
        Web.  doi:10.2172/1032129.

Copy to clipboard


                    Kuwazaki, A., & /Fermilab. Control Dewar and VLPC Bayonet Can Platform Connection Design and Analysis.  United States.  https://doi.org/10.2172/1032129

Copy to clipboard


                    Kuwazaki, A., and /Fermilab. Tue .  
        "Control Dewar and VLPC Bayonet Can Platform Connection Design and Analysis".  United States.  https://doi.org/10.2172/1032129.  https://www.osti.gov/servlets/purl/1032129.

Copy to clipboard


                    
@article{osti_1032129,

  title        = {Control Dewar and VLPC Bayonet Can Platform Connection Design and Analysis},

  author       = {Kuwazaki, A. and /Fermilab},

  abstractNote = {The four connections for the control dewar and VLPC bayonet can platform are designed, using finite element analysis, to carry all dead weight and live loads. Based on the loads applied to the platform, two 1 inch thick plates and two 3/4 inch thick brackets made of ASTM A572-Grade 42 are required. The 1 inch thick plate requires a 3/8 inch thick intermediate steel material, between the 8-inch x 4-inch x 1/4-inch boom and the plate, for load reinforcement as well as weld area reinforcement. Both the plates and the brackets require 3/4 inch steel bolt connections.},

  doi          = {10.2172/1032129},

  url          = {https://www.osti.gov/biblio/1032129},
  journal      = {},
number       = ,

  volume       = ,

  place        = {United States},

  year         = {1997},

  month        = {7}

}

Copy to clipboard

Technical Report:

View Technical Report (1.81 MB)

https://doi.org/10.2172/1032129

Save / Share:

Export Metadata

Save to My Library

Similar records in OSTI.GOV collections:

Design Document for Control Dewar and Vacuum Pump Platforms

Technical Report Rucinksi, R. ; /Fermilab

This engineering note documents the design of the control dewar and vacuum pump platform that is to be installed on the D-Zero detector. It's purpose is twofold. Firstly it is a summary and repository of the final design calculations of the structure. Secondly, it documents that design follows the American Institute of Steel Construction (AISC) manual and applicable OSHA requirements with respect to walking working surfaces. The information contained in the main body of this note is supported by raw calculations included as the appendix. The platform is a truss type frame strucrure constructed primarily of rectangular steel tubing. Themore »« less
https://doi.org/10.2172/1032125

Full Text Available
D0 Silicon Upgrade: West End Assembly Hall Platform Design Calculations

Technical Report Rucinski, Russ ; /Fermilab

This engineering note documents design calculations done for the bayonet feed can platform installed at the far west end of the assembly hall. The platform is mounted off of a cast concrete wall directly south of where the shielding block wall is stacked. A summary of the loading, reaction forces and stresses is shown on the page 3. As can be seen, the calculated stresses are very small, maximum value = 2540 psi. The material used is structural steel tubing, ASTM A500 Gr. B, with a minimum yield strength of 46 ksi and minimum ultimate tensile strength of 58 ksi.more »« less
https://doi.org/10.2172/1033290

Full Text Available
Design of a 2 Slot VLPC Cryostat Cooled by a Cryocooler

Technical Report Rucinski, Russell A. ; /Fermilab

The conceptual design and preliminary engineering calculations have been completed for a two cassette cryostat. This report summarizes the design. A cryocooler is permanently mounted in the center of a stainless steel, 0.75 inch thick top lid. The cryocooler sits upon a spacer which raises the cooling stage elevations to favorably match the cassette heat intercept elevations. The top lid (32.0-inch outside diameter) mates to a 24-inch pipe size flange with o-ring. The 24-inch pipe size vacuum vessel with end plate has a minimum internal depth of 16-inch to give adequate clearance for the depth of the cryocooler and multilayermore »« less
https://doi.org/10.2172/1033659

Full Text Available
Manufacturing and testing VLPC hybrids

Journal Article Adkins, L R ; Ingram, C M ; Anderson, E J - AIP Conference Proceedings

To insure that the manufacture of VLPC devices is a reliable, cost-effective technology, hybrid assembly procedures and testing methods suitable for large scale production have been developed. This technology has been developed under a contract from Fermilab as part of the D-Zero upgrade program. Each assembled hybrid consists of a VLPC chip mounted on an AlN substrate. The VLPC chip is provided with bonding pads (one connected to each pixel) which are wire bonded to gold traces on the substrate. The VLPC/AlN hybrids are mated in a vacuum sealer using solder preforms and a specially designed carbon boat. After mating,more »« less
https://doi.org/10.1063/1.56979
D0 Silicon Upgrade: ASME Code and Pressure Calculations for Liquid Nitrogen Subcooler

Technical Report Kuwazaki, Andrew ; Leicht, Todd ; /Fermilab

Included in this engineering note are three separate calculation divisions. The first calculations are the determination of the required thickness of the LN{sub 2} subcooler flat head according to ASME code. This section includes Appendix A-C. The minimum plate thickness determined was 0.563 in. The actual thickness chosen in fabrication was a 3/4-inch plate milled to 0.594-inch at the bolt circle. Along with the plate thickness, this section calculates the required reinforcement area at the top plate penetrations. It was found that a 1/4-inch fillet weld at each penetration was adequate. The next set of calculations were done to provemore »« less
https://doi.org/10.2172/1033296

Full Text Available

Similar Records