Pulsed atmospheric fluidized bed combustion. Quarterly report, July 1--September 30, 1995

doi:10.2172/663337

Title: Pulsed atmospheric fluidized bed combustion. Quarterly report, July 1--September 30, 1995

Full Record
Other Related Research

Abstract

The report summarizes progress in design, fabrication, and construction activities. Progress on the fluid bed combustor, piping, fuel feeding system, ash system, and the control and instrumentation design is described. The report lists the construction activities completed during this quarter which included bed tubes installation, fan inlet flow measuring duct, bag filter, silencers for roots blowers, electric power cabling connections, light distributor panel and transformer installation inside the control panel, steam/water recirculation piping, fine coal receiving vent filter, and partial painting of ash silo and boiler.

Publication Date:: Sun Dec 31 00:00:00 EST 1995

Research Org.:: ThermoChem, Inc., Columbia, MD (United States)

Sponsoring Org.:: USDOE Assistant Secretary for Fossil Energy, Washington, DC (United States)

OSTI Identifier:: 663337

Report Number(s):: DOE/MC/27229-5749
ON: DE97053808; TRN: AHC29818%%174

DOE Contract Number:: FC21-90MC27229

Resource Type:: Technical Report

Resource Relation:: Other Information: PBD: [1995]

Country of Publication:: United States

Language:: English

Subject:: 01 COAL, LIGNITE, AND PEAT; PROGRESS REPORT; FLUIDIZED BED BOILERS; DESIGN; FABRICATION; CONSTRUCTION; AUXILIARY SYSTEMS; MATERIALS HANDLING EQUIPMENT; POLLUTION CONTROL EQUIPMENT

Citation Formats


                    . Pulsed atmospheric fluidized bed combustion. Quarterly report, July 1--September 30, 1995.  United States: N. p., 1995. 
        Web.  doi:10.2172/663337.

Copy to clipboard


                    . Pulsed atmospheric fluidized bed combustion. Quarterly report, July 1--September 30, 1995.  United States.  https://doi.org/10.2172/663337

Copy to clipboard


                    . 1995.  
        "Pulsed atmospheric fluidized bed combustion. Quarterly report, July 1--September 30, 1995".  United States.  https://doi.org/10.2172/663337.  https://www.osti.gov/servlets/purl/663337.

Copy to clipboard


                    
@article{osti_663337,

  title        = {Pulsed atmospheric fluidized bed combustion. Quarterly report, July 1--September 30, 1995},

  author       = {},

  abstractNote = {The report summarizes progress in design, fabrication, and construction activities. Progress on the fluid bed combustor, piping, fuel feeding system, ash system, and the control and instrumentation design is described. The report lists the construction activities completed during this quarter which included bed tubes installation, fan inlet flow measuring duct, bag filter, silencers for roots blowers, electric power cabling connections, light distributor panel and transformer installation inside the control panel, steam/water recirculation piping, fine coal receiving vent filter, and partial painting of ash silo and boiler.},

  doi          = {10.2172/663337},

  url          = {https://www.osti.gov/biblio/663337},
  journal      = {},
number       = ,

  volume       = ,

  place        = {United States},

  year         = {Sun Dec 31 00:00:00 EST 1995},

  month        = {Sun Dec 31 00:00:00 EST 1995}

}

Copy to clipboard

Technical Report:

View Technical Report (1.43 MB)

https://doi.org/10.2172/663337

Save / Share:

Export Metadata

Save to My Library

Similar records in OSTI.GOV collections:

Pulsed atmospheric fluidized bed combustion. Technical progress report, April--June 1995

Technical Report

Design activities for this report period included: (1) Mechanical. Stress analysis calculations were performed on the steam/water pressure piping. Pipe support design and drawings were completed by Duke Fluor Daniel. The fluid bed distributor bubble cap design was revisited and changes made for ease of maintenance. (2) Electrical and Instrumentation. Control and instrumentation scheme proposed earlier, was based on independent single loop controllers. After careful review, it is decided to go for state of art distributed control system (DCS) which uses programmable logic controllers (PLC). In addition, coal/limestone pickup hopper fabrication was completed during this period and shipped to themore »« less
https://doi.org/10.2172/113918

Full Text Available
Establishment of an Environmental Control Technology Laboratory with a Circulating Fluidized-Bed Combustion System

Technical Report Pan, Wei-Ping; Cao, Yan; Smith, John

This report is to present the progress made on the project entitled ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period January 1, 2007 through March 31, 2007. The effort in this quarter has concentrated on installing the CFBC Facility and for conducting cold fluidization operations tests in the CFBC facility. The assembly of the ash recirculation pipe duct from the cyclones back to the bed area of the combustor, including the upper and lower loop seals was completed. The electric bed pre-heater was installed to heat the fluidizing air asmore »« less
https://doi.org/10.2172/902975

Full Text Available
Pulsed atmospheric fluidized bed combustion. Quarterly technical progress report, April--June 1993

Technical Report

In this quarter the design of the plant structures was completed 70%. The design philosophy of the structure economizes on the use of steel by providing supports for the hot cyclone and hot gas duct connecting the cyclone to the boiler while fulfilling the needs for platforms and walkways at the various levels necessary for operational access. Figures 1 through 6 indicate the layout of the plant structure. At the same time the structure for the Coarse Coal Silo V-2 and Limestone Silo V-4 were incorporated and completed. Following completion of the piping pressure drop calculations, pipe sizing and layoutmore »« less
https://doi.org/10.2172/10115231

Full Text Available
Pulsed atmospheric fluidized bed combustion

Technical Report

The Design and Engineering of most components in the Pulsed Atmospheric Fluidized Bed System was completed prior to September 1992. The components remaining to be designed at that time were: Aerovalves for the Pulse Combustor; Gas and coal injectors for the Pulse Combustor; Lines for PC tailpipes; Air plenum and inlet silencer; Refractory lined hot gas duct connecting outlet hot cyclone to boiler; Structure and platforms, and ladders around PAFBC vessel access and major equipment. Design work is currently in progress on all of the above components. Items 1, 2, 3 and 4 are 50% completed, and items 5 6more » are 75% complete.« less
https://doi.org/10.2172/6735746

Full Text Available
Pulsed atmospheric fluidized bed combustion. Quarterly technical progress report, October 1992--December 1992

Technical Report

The Design and Engineering of most components in the Pulsed Atmospheric Fluidized Bed System was completed prior to September 1992. The components remaining to be designed at that time were: Aerovalves for the Pulse Combustor; Gas and coal injectors for the Pulse Combustor; Lines for PC tailpipes; Air plenum and inlet silencer; Refractory lined hot gas duct connecting outlet hot cyclone to boiler; Structure and platforms, and ladders around PAFBC vessel access and major equipment. Design work is currently in progress on all of the above components. Items 1, 2, 3 and 4 are 50% completed, and items 5 &more » 6 are 75% complete.« less
https://doi.org/10.2172/10135060

Full Text Available

Similar Records