A hardenability test proposal

Murthy, N V.S.N.

Title: A hardenability test proposal

Full Record
Other Related Research

Abstract

A new approach for hardenability evaluation and its application to heat treatable steels will be discussed. This will include an overview and deficiencies of the current methods and discussion on the necessity for a new approach. Hardenability terminology will be expanded to avoid ambiguity and over-simplification as encountered with the current system. A new hardenability definition is proposed. Hardenability specification methods are simplified and rationalized. The new hardenability evaluation system proposed here utilizes a test specimen with varying diameter as an alternative to the cylindrical Jominy hardenability test specimen and is readily applicable to the evaluation of a wide variety of steels with different cross-section sizes.

Authors:

Murthy, N V.S.N. ^[1]

Ingersoll-Rand (I) Ltd., Bangalore (India)

Publication Date:: Tue Dec 31 00:00:00 EST 1996

OSTI Identifier:: 484254

Report Number(s):: CONF-961140-
TRN: 97:000168-0015

Resource Type:: Conference

Resource Relation:: Conference: 2. international conference on quenching and the control of distortion, Cleveland, OH (United States), 4-7 Nov 1996; Other Information: PBD: 1996; Related Information: Is Part Of 2nd International conference on quenching and the control of distortion; Totten, G.E.; Howes, M.A.H.; Sjoestrom, S.J.; Funatani, Kiyoshi [eds.]; PB: 652 p.

Country of Publication:: United States

Language:: English

Subject:: 36 MATERIALS SCIENCE; STEELS; QUENCH HARDENING; MEASURING METHODS

Citation Formats


                    Murthy, N V.S.N. A hardenability test proposal.  United States: N. p., 1996. 
        Web.

Copy to clipboard


                    Murthy, N V.S.N. A hardenability test proposal.  United States.

Copy to clipboard


                    Murthy, N V.S.N. 1996.  
        "A hardenability test proposal".  United States.

Copy to clipboard


                    
@article{osti_484254,

  title        = {A hardenability test proposal},

  author       = {Murthy, N V.S.N.},

  abstractNote = {A new approach for hardenability evaluation and its application to heat treatable steels will be discussed. This will include an overview and deficiencies of the current methods and discussion on the necessity for a new approach. Hardenability terminology will be expanded to avoid ambiguity and over-simplification as encountered with the current system. A new hardenability definition is proposed. Hardenability specification methods are simplified and rationalized. The new hardenability evaluation system proposed here utilizes a test specimen with varying diameter as an alternative to the cylindrical Jominy hardenability test specimen and is readily applicable to the evaluation of a wide variety of steels with different cross-section sizes.},

  doi          = {},

  url          = {https://www.osti.gov/biblio/484254},
  journal      = {},
number       = ,

  volume       = ,

  place        = {United States},

  year         = {Tue Dec 31 00:00:00 EST 1996},

  month        = {Tue Dec 31 00:00:00 EST 1996}

}

Copy to clipboard

Conference:

Other availability

Please see Document Availability for additional information on obtaining the full-text document. Library patrons may search WorldCat to identify libraries that hold this conference proceeding.

Save / Share:

Export Metadata

Save to My Library

Similar records in OSTI.GOV collections:

Correction of Specimen Strain Measurement in Kolsky Tension Bar Experiments on Work-Hardening Materials

Journal Article Song, Bo; Sanborn, Brett; Susan, Donald; ... - International Journal of Impact Engineering

Cylindrical dog-bone (or dumbbell) shaped samples have become a common design for dynamic tensile tests of ductile materials with a Kolsky tension bar. When a direct measurement of displacement between the bar ends is used to reveal the specimen strain, the actual strain in the specimen gage section is overestimated due to strain in the specimen shoulder and needs to be corrected. The currently available correction method works well for elastic-perfectly plastic materials but may not be applicable to materials that exhibit significant work-hardening behavior. Here, we developed a new specimen strain correction method for materials possessing an elastic-plastic withmore »« less
Cited by 5
https://doi.org/10.1016/j.ijimpeng.2019.103328

Full Text Available
Effect of the Ti/N ratio on the hardenability and mechanical properties of a quenched-and-tempered C-Mn-B steel

Journal Article Shen, Y; Hansen, S - Metallurgical and Materials Transactions. A, Physical Metallurgy and Materials Science

Ten experimental 0.18 pct C-1.2 pct Mn-0.002 pct B steels with various Ti/N ratios were evaluated in this study. The hardenability of these steels was first determined using Jominy tests. Slab sections were then rolled to produce 12.5-mm-thick plates, and subsequently quenched and tempered for mechanical property evaluation. The volume fraction of coarse (greater than 1 {micro}m) TiN particles was measured in all steels using quantitative metallographic techniques. Scanning transmission electron microscopy was used to investigate fine precipitates, and scanning electron microscopy was used to examine the fracture surface of Charpy specimens. The results show that a complete boron (B)more »« less
https://doi.org/10.1007/s11661-997-0159-6
Implementation of ANL’s Mechanics Based Evolutionary Fatigue Modeling Through ABAQUS-WARP3D Based High-Performance Computing Framework

Technical Report Mohanty, Subhasish; Barua, Bipul; Listwan, Joseph; ...

This report presents an update on the environmental fatigue research that is being conducted at Argonne National Laboratory in support of the Department of Energy’s Light Water Reactor Sustainability (LWRS) program. Argonne is developing a fully mechanistic fatigue evaluation approach without using empirical fatigue (S~N) curves. This approach is based on the fundamental concept of the time evolution of progressive fatigue damage rather than on the conventional S~N curve approaches using end-of-life data. In FY 2017, we performed extensive validation of this approach with respect to fatigue test data for 316 stainless steel [1]. This validation was performed for differentmore »« less
https://doi.org/10.2172/1480516

Full Text Available
Determination of Anisotropic Hardening of Sheet Metals by Shear Tests

Journal Article Schikorra, Marco; Brosius, Alexander; Kleiner, Matthias - AIP Conference Proceedings

With regard to the increasing necessity of accurate material data determination for the prediction of springback, a material testing equipment has been developed and set up for the measurement of material hardening within cyclic loading. One reason for inaccurate springback predictions can be seen in a missing consideration of load reversal effects in a realistic material model description. Due to bending and unbending while the material is drawn from the flange over a radius of a deep drawing tool, a hardening takes place which leads to an expanding or shifting of the elastic area and yield locus known as isotropic,more »« less
https://doi.org/10.1063/1.2011251
Novel Carbon (C)-Boron (B)-Nitrogen (N)-Containing H2 Storage Materials

Technical Report Liu, Shih-Yuan; Giustra, Zachary; Autrey, Tom; ...

The following summarizes the research conducted for DOE project DE-EE0005658 “Novel Carbon(C)-Boron(B)-Nitrogen(N)-Containing H2 Storage Materials”. This work focused in part on the continued study of two materials identified from the preceding project DE-FG360GO18143 (“Hydrogen Storage by Novel CBN Heterocycle Materials”) as lead candidates to meet the DOE technical targets for either vehicular or non-automotive hydrogen storage applications. Specifically, a room-temperature liquid, 3-methyl-1,2-cyclopentane (B), and a high H2 capacity solid, 1,2-BN-cyclohexane (J), were selected for further characterization and performance optimization. In addition to these compounds, the current project also aimed to prepare several new materials predicted to be disposed towards directmore »« less
https://doi.org/10.2172/1393260

Full Text Available

Similar Records