Powered by Deep Web Technologies
Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Waste to Energy Time Activities  

E-Print Network (OSTI)

SEMINAR Waste to Energy Time Activities 9:30-9:40 Brief introduction of participants 9:40-10:10 Presentation of Dr. Kalogirou, "Waste to Energy: An Integral Part of Worldwide Sustainable Waste Management" 10. Sofia Bethanis, "Production of synthetic aggregates for use in structural concrete from waste to energy

Columbia University

2

CCA-Treated wood disposed in landfills and life-cycle trade-offs with waste-to-energy and MSW landfill disposal  

E-Print Network (OSTI)

Environmental Protection Agency (US EPA) regulations, it produces energy and does not emit fossil carbonCCA-Treated wood disposed in landfills and life-cycle trade-offs with waste-to-energy and MSW in waste-to-energy (WTE) facilities. In other countries, the predominant disposal option for wood

Florida, University of

3

Waste to Energy Technologies | Open Energy Information  

Open Energy Info (EERE)

Waste to Energy Technologies Jump to: navigation, search Name Waste to Energy Technologies Place Madrid, Spain Zip 28023 Sector Biomass Product Turn key WtEbiomass plant supplier...

4

Optimizing Organic Waste to Energy Operations  

Science Conference Proceedings (OSTI)

A waste-to-energy firm that recycles organic waste with energy recovery performs two environmentally beneficial functions: it diverts waste from landfills and it produces renewable energy. At the same time, the waste-to-energy firm serves and collects ... Keywords: environment, operating strategy, organic waste to energy, regulation, sustainability

Bar?? Ata; Deishin Lee; Mustafa H. Tongarlak

2012-04-01T23:59:59.000Z

5

AUSTRIA SHOWCASE WASTE-to-ENERGY  

E-Print Network (OSTI)

1 AUSTRIA SHOWCASE WASTE-to-ENERGY in AUSTRIA AECC Aberdeen Exhibition & Conference Center (M.I.T.) #12;2 Table of Content · Development of waste management in Austria · Status-Quo of waste management in EU countries · Separated collection: Recycling and Waste-to-Energy · Development of emission

Hone, James

6

EA-1862: Oneida Seven Generation Corporation Waste-To-Energy...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

62: Oneida Seven Generation Corporation Waste-To-Energy System, Ashwaubenon, Wisconsin EA-1862: Oneida Seven Generation Corporation Waste-To-Energy System, Ashwaubenon, Wisconsin...

7

The Conversion of Waste to Energy  

E-Print Network (OSTI)

Almost every industrial operation produces some combustible waste, but conversion of this to useful energy is often more difficult than with other energy recovery projects and requires careful attention to design, operating and maintaining the facilities. Each application requires a careful approach tailored to the installation, but some general design and economic principles do exist. Several waste to energy projects will be discussed to illustrate these principles.

John, T.; Cheek, L.

1980-01-01T23:59:59.000Z

8

Waste To Energy -Strategies and Payoffs  

E-Print Network (OSTI)

Many industrial firms are taking a hard look at converting waste to energy. The opportunities for positive significant operational impact are not without large capital outlays. Past experiences indicate that an understanding of the basic alternatives, strategies, and typical economic performance can go a long way in directing corporate efforts, and in engineering an economically viable project. This paper addresses boiler-and engine-based systems, their performance and operating advantages and disadvantages, and the economic performance of each of the major hardware alternatives. This formulation and decision process for actual waste to energy projects is examined with sample energy and economic examples. These results should assist the energy manager in deciding between waste-fired cogeneration or conversion of the powerhouse to alternative fuels.

Gilbert, J. S.

1982-01-01T23:59:59.000Z

9

Energy Recovery Council (ERC) Wast to Energy (WTE) | Open Energy  

Open Energy Info (EERE)

Energy Recovery Council (ERC) Wast to Energy (WTE) Energy Recovery Council (ERC) Wast to Energy (WTE) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Energy Recovery Council (ERC) Wast to Energy (WTE) Agency/Company /Organization: Energy Recovery Council (ERC) Sector: Energy Focus Area: Biomass, - Waste to Energy Phase: Create a Vision Resource Type: Dataset, Publications, Guide/manual User Interface: Website Website: www.wte.org/ Cost: Free The Energy Recovery Council is a national trade organization representing the waste-to-energy industry and communities that own waste-to-energy facilities. Overview The Energy Recovery Council is a national trade organization representing the waste-to-energy industry and communities that own waste-to-energy facilities. The website includes information on waste-to-energy basics

10

Waste-to-Energy Biomass Digester with Decreased Water Consumption  

Waste-to-Energy Biomass Digester with Decreased Water Consumption Contact Information: Jeremy Nelson Phone: 970.491.7100 Email: ...

11

Waste-to-Energy Biomass Digester with Decreased Water ...  

Waste-to-Energy Biomass Digester with Decreased Water Consumption Contact Information: Jeremy Nelson Phone: 970.491.7100 Email: ...

12

Global Waste to Energy Conversion Company GWECC | Open Energy Information  

Open Energy Info (EERE)

Waste to Energy Conversion Company GWECC Waste to Energy Conversion Company GWECC Jump to: navigation, search Name Global Waste to Energy Conversion Company (GWECC) Place Washington, DC Product GWECC is a global alternative energy company headquartered in Washington DC, USA. References Global Waste to Energy Conversion Company (GWECC)[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Global Waste to Energy Conversion Company (GWECC) is a company located in Washington, DC . References ↑ "Global Waste to Energy Conversion Company (GWECC)" Retrieved from "http://en.openei.org/w/index.php?title=Global_Waste_to_Energy_Conversion_Company_GWECC&oldid=345924" Categories: Clean Energy Organizations

13

Waste-to-Energy Biomass Digester with Decreased Water Consumption  

Waste-to-Energy Biomass Digester with Decreased Water Consumption ... Able to digest multiple types of waste, including bovine, equine, and poultry manure

14

Waste-to-energy compendium. Final report  

DOE Green Energy (OSTI)

A survey is made of 35 waste-to-energy recovery projects throughout the US. Included are nine refuse-derived fuel (RDF) production facilities, six RDF user facilities, two combined RDF production-user facilities, and 18 mass burning facilities with energy recovery. Only those facilities that are fully operational or those in advanced stages of startup and shakedown are surveyed. Information is provided on processing capacities, operation and maintenance problems, equipment specifications, capital and operating costs, and the current status of each facility. In addition, process flow schematics are provided for each of the nine RDF production plants and both RDF production-user plants. Unless otherwise indicated, the data in this report have been updated to October or November, 1980.

Not Available

1981-04-01T23:59:59.000Z

15

An Overview of Hot Corrosion in Waste to Energy Boiler ...  

Science Conference Proceedings (OSTI)

Presentation Title, An Overview of Hot Corrosion in Waste to Energy Boiler ... boiler designers, and boiler tube manufacturers since quite a few number of boiler...

16

NREL: Technology Deployment - Biopower and Waste-to-Energy Solutions  

NLE Websites -- All DOE Office Websites (Extended Search)

Opportunities, and Options for Advancing Bioenergy Waste-to-Energy Evaluation: U.S. Virgin Islands See all our publications Printable Version Technology Deployment Home...

17

Kent County Waste to Energy Facility Biomass Facility | Open Energy  

Open Energy Info (EERE)

Kent County Waste to Energy Facility Biomass Facility Kent County Waste to Energy Facility Biomass Facility Jump to: navigation, search Name Kent County Waste to Energy Facility Biomass Facility Facility Kent County Waste to Energy Facility Sector Biomass Facility Type Municipal Solid Waste Location Kent County, Michigan Coordinates 43.0097027°, -85.520024° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":43.0097027,"lon":-85.520024,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

18

EA-1860: Richland Renewable Energy Waste-to-Energy Project, Richland...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0: Richland Renewable Energy Waste-to-Energy Project, Richland, Wisconsin EA-1860: Richland Renewable Energy Waste-to-Energy Project, Richland, Wisconsin Summary This EA evaluates...

19

EA-0952: The Louisiana State University Waste-to Energy Incinerator...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2: The Louisiana State University Waste-to Energy Incinerator, Baton Rouge, Louisiana EA-0952: The Louisiana State University Waste-to Energy Incinerator, Baton Rouge, Louisiana...

20

Waste-to-Energy and Fuel Cell Technologies Overview  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste-to-Energy and Fuel Cell Waste-to-Energy and Fuel Cell T h l i O i Innovation for Our Energy Future Technologies Overview Presented to: DOD-DOE Waste-to- Energy Workshop Energy Workshop Dr. Robert J. Remick J 13 2011 January 13, 2011 Capital Hilton Hotel Washington, DC NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. Global Approach for Using Biogas Innovation for Our Energy Future Anaerobic Digestion of Organic Wastes is a Good Source of Methane. Organic waste + methanogenic bacteria → methane (CH 4 ) Issues: High levels of contamination Time varying output of gas quantity and quality Innovation for Our Energy Future Photo courtesy of Dos Rios Water Recycling Center, San Antonio, TX

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

COST-BENEFIT ANALYSIS OF A WASTE TO ENERGY PLANT FOR MONTEVIDEO; AND WASTE TO  

E-Print Network (OSTI)

1 COST-BENEFIT ANALYSIS OF A WASTE TO ENERGY PLANT FOR MONTEVIDEO; AND WASTE TO ENERGY IN SMALL-benefit analysis by the author of a waste to energy (WTE) plant in Montevideo, Uruguay; the second part Engineering Center of Columbia University investigated the waste management system of Montevideo, Uruguay

Columbia University

22

Waste-to-Energy Evaluation: U.S. Virgin Islands  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste-to-Energy Evaluation: Waste-to-Energy Evaluation: U.S. Virgin Islands Jerry Davis, Scott Haase, and Adam Warren Technical Report NREL/TP-7A20-52308 August 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Waste-to-Energy Evaluation: U.S. Virgin Islands Jerry Davis, Scott Haase, and Adam Warren Prepared under Task No(s). IDVI.0000 and IDVI.0032 Technical Report NREL/TP-7A20-52308 August 2011 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government.

23

9th Annual North American Waste to Energy Conference A CANADIAN PERSPECTIVE ON WASTE-TO-ENERGY  

E-Print Network (OSTI)

-TO-ENERGY Ninth Annual North American Waste-To-Energy Conference May 6-9, 2001 Miami, Florida Rob C. Rivers, CET on a real time basis, via remote modem from the Region's and MacViro offices. · Providing for monthly area for the waste prior to being loaded into the incinerator. The storage area has a capacity

Columbia University

24

Waste to Energy and Absorption Chiller: A Case Study  

E-Print Network (OSTI)

All measured performance characteristics corresponded well to manufacturer's specifications or were within the expected range for this type of incinerator. The simplified economic analysis showed a payback of period 4.5 years. An optimized payback calculation based on a set of possible improvements to the waste-to-energy system showed a payback period of 3.8 years.

Wolpert, J.

1990-01-01T23:59:59.000Z

25

Waste-to-Energy Evaluation: U.S. Virgin Islands  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Waste-to-Energy Evaluation: U.S. Virgin Islands Jerry Davis, Scott Haase, and Adam Warren Technical Report NREL/TP-7A20-52308 August 2011 NREL is a national laboratory of the U.S. Department of Energy, Office of Energy Efficiency & Renewable Energy, operated by the Alliance for Sustainable Energy, LLC. National Renewable Energy Laboratory 1617 Cole Boulevard Golden, Colorado 80401 303-275-3000 * www.nrel.gov Contract No. DE-AC36-08GO28308 Waste-to-Energy Evaluation: U.S. Virgin Islands Jerry Davis, Scott Haase, and Adam Warren Prepared under Task No(s). IDVI.0000 and IDVI.0032 Technical Report NREL/TP-7A20-52308 August 2011 NOTICE This report was prepared as an account of work sponsored by an agency of the United States government.

26

Waste to Energy Power Production at DOE and DOD Sites  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste to Energy Power Production Waste to Energy Power Production at DOE and DOD Sites January 13, 2011 Overview - Federal Agency Innovations DOE: S avannah River S ite * Biomass Heat and Power US AF: Hill Air Force Base * Landfill Gas to Energy Generation Ameresco independent DOES avannah River S ite DOES avannah River S ite (DOE-S R) * Georgia / S outh Carolina border * 300+ sq miles extending into 3 counties * Began operations in 1950s Challenges faced by DOE-S R * Aging Infrastructure Ameresco independent * Coal and fuel oil power plants * Increased / new clean air requirements * New energy efficiency / sustainability requirements Business Case Analysis S ite need for both steam and power Repair, renovate, or replace Mandates and desire for renewable energy solution Appropriated funds not available

27

Waste-to-Energy using Fuel Cells Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste-to-Energy using Fuel Cells Workshop Capital Hilton Hotel, Washington DC January 13th, 2011 8:30 am to 5:00 pm Agenda 8:30 am Welcome, introductions and meeting logistics Pete Devlin, Department of Energy (DOE) Fuel Cell Technologies Program Overall Purpose * To identify DOD-DOE waste-to-energy and fuel cells opportunities * To identify challenges and determine actions to address them * To determine specific ways fuel cell and related technologies can help meet Executive Order 13514 requirements * To identify the next steps for collaboration Background Materials Provided * DOD-DOE MOU - http://www.energy.gov/news/documents/Enhance-Energy-Security-MOU.pdf * Executive Order 13514 - http://edocket.access.gpo.gov/2009/pdf/E9-24518.pdf

28

16th North American Waste to Energy Conference-May 2008 CO2 Enhanced Steam Gasification of Biomass Fuels  

E-Print Network (OSTI)

16th North American Waste to Energy Conference-May 2008 CO2 Enhanced Steam Gasification of Biomass of the decomposition of various biomass feedstocks and their conversion to gaseous fuels such as hydrogen. The steam temperatures: above 500o C for the herbaceous and non-wood samples and above 650o C for the wood biomass fuels

29

Fuel Cell Technologies Office: Waste-to-Energy using Fuel Cells...  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste-to-Energy using Fuel Cells Workshop to someone by E-mail Share Fuel Cell Technologies Office: Waste-to-Energy using Fuel Cells Workshop on Facebook Tweet about Fuel Cell...

30

Fuel Cell Technologies Office: Waste-to-Energy using Fuel Cells...  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste-to-Energy using Fuel Cells Webinar to someone by E-mail Share Fuel Cell Technologies Office: Waste-to-Energy using Fuel Cells Webinar on Facebook Tweet about Fuel Cell...

31

Waste-to-Energy Evaluation: U.S. Virgin Islands  

SciTech Connect

This NREL technical report evaluates the environmental impact and fundamental economics of waste-to-energy (WTE) technology based on available data from commercially operating WTE facilities in the United States. In particular, it considers life-cycle impacts of WTE as compared to landfill disposal and various forms of electrical generation, as well as WTE impacts on source reduction or recycling programs. In addition, it evaluates the economics and potential environmental impact of WTE in the U.S. Virgin Islands (USVI) based on existing USVI waste stream characterization data, recycling challenges unique to the USVI, and the results of cost and environmental modeling of four municipal solid waste (MSW) management options, including landfill, refuse-derived fuel (RDF) production, recycling, and gassification plus RDF.

Davis, J.; Hasse, S.; Warren, A.

2011-08-01T23:59:59.000Z

32

Prefeasibility Study for a Waste-to-EnergyApplication in Gauteng Province, South Africa.  

E-Print Network (OSTI)

?? Waste-to-Energy concept becomes increasingly popular from the perspectives of the waste management and alternative energy. South Africa, which is a country heavily dependent on (more)

Subasinghe, Gayan

2013-01-01T23:59:59.000Z

33

Proceedings of the 1st Installation Waste to Energy Workshop  

E-Print Network (OSTI)

Approved for public release; distribution is unlimited. Prepared for U.S. Army Corps of Engineers Washington, DC 20314-1000ERDC/CERL TR-08-11 ii Abstract: This first-ever waste to energy (WTE) workshop gathered Army environmental and energy subject matter experts to explore WTE at the installation and forward operating level. Historically, the Army environmental community has focused on solid waste disposal and the energy community on energy efficiency and power delivery, with no orchestrated integration of the two. The Energy Branch of the U.S. Army Engineer Research and Development Center, Construction Engineering Research Laboratory has been investigating WTE opportunities, and has found little Army analysis on WTE system providers many claims. The goals of this workshop were to share information, spread visibility on

Franklin H. Holcomb; Ren S. Parker; Thomas J. Hartranft; Kurt Preston; Harold R. Sanborn; Philip J. Darcy; Franklin H. Holcomb; Ren S. Parker; Thomas J. Hartranft; Kurt Preston; Harold R. Sanborn; Philip J. Darcy

2008-01-01T23:59:59.000Z

34

Waste-to-Energy Research and Technology Council (WTERT) | Open Energy  

Open Energy Info (EERE)

Waste-to-Energy Research and Technology Council (WTERT) Waste-to-Energy Research and Technology Council (WTERT) Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Wast-to-Energy Research and Technology Council (WTERT) Agency/Company /Organization: Wast-to-Energy Research and Technology Council (WTERT) Sector: Energy, Land, Climate Focus Area: Biomass, - Waste to Energy, Greenhouse Gas Phase: Create a Vision Resource Type: Dataset, Maps, Presentation, Publications, Guide/manual, Training materials, Case studies/examples User Interface: Website Website: www.seas.columbia.edu/earth/wtert Cost: Free The Waste-to-Energy Research and Technology Council (WTERT) brings together engineers, scientists and managers from universities and industry. The mission of WTERT is to identify and advance the best available

35

Incineration, Waste-to-energy and Catalytic Gasification: the Past, Present and Future of Medical Waste Management  

E-Print Network (OSTI)

- 1 - Incineration, Waste-to-energy and Catalytic Gasification: the Past, Present and Future Determination 19 Discussion of M.W. Disposal/Use Options Incineration 25 Waste-to-Energy 28 Gasification 29 Waste-to-Energy Ash Research 31 Dioxins 35 Discussion of Gasification/Catalytic Alternative 36 GCMS

Columbia University

36

11th North American Waste to Energy Conference Copyright C 2003 by ASME  

E-Print Network (OSTI)

11th North American Waste to Energy Conference Copyright C 2003 by ASME NAWTEC11-1688 Innovative in central Florida, Pinellas County has continuously sought to reduce potable water usage at its facilities. BACKGROUND The PCRRF is a mass bum waste-to-energy plant serving the densely populated Pinellas County

Columbia University

37

Proceedings of NAWTEC 16 North American Waste-to-Energy Conference 16  

E-Print Network (OSTI)

types and usage levels, facility energy consumption data) to account for emission reductions resulting1 Proceedings of NAWTEC 16 North American Waste-to-Energy Conference 16 May 19 -21, 2008 their carbon footprint. In an article published in the proceedings for the National Waste-to-Energy Conference

Columbia University

38

Proceedings of NAWTEC16 16th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

of the energy generated is optimized. HISTORY WTE's were constructed and began operations under regulatedProceedings of NAWTEC16 16th Annual North American Waste-to-Energy Conference May 19-21, 2008, Philadelphia, Pennsylvania, USA NAWTEC16-1913 OPTIONS AND STRATEGIES FOR WASTE TO ENERGY FACILITY ENERGY SALES

Columbia University

39

Ris-R-Report Energy Systems Analysis of Waste to Energy  

E-Print Network (OSTI)

Risø-R-Report Energy Systems Analysis of Waste to Energy Technologies by use of EnergyPLAN Marie Münster Risø-R-1667(EN) April 2009 #12;Author: Marie Münster Title: Energy Systems Analysis of Waste to Energy Technologies by use of EnergyPLAN Division: Systems Analysis Division Risø-R-1667(EN) April 2009

40

Waste-to-Energy Research and Technology Council (WTERT) | Open Energy  

Open Energy Info (EERE)

form form View source History View New Pages Recent Changes All Special Pages Semantic Search/Querying Get Involved Help Apps Datasets Community Login | Sign Up Search Page Edit with form History Facebook icon Twitter icon » Waste-to-Energy Research and Technology Council (WTERT) (Redirected from Wast-to-Energy Research and Technology Council (WTERT)) Jump to: navigation, search Tool Summary Name: Wast-to-Energy Research and Technology Council (WTERT) Agency/Company /Organization: Wast-to-Energy Research and Technology Council (WTERT) Sector: Energy, Land, Climate Focus Area: Biomass, - Waste to Energy, Greenhouse Gas Phase: Create a Vision Resource Type: Dataset, Maps, Presentation, Publications, Guide/manual, Training materials, Case studies/examples User Interface: Website

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

9th Annual North American Waste to Energy Conference Jack A. Ristau  

E-Print Network (OSTI)

made by U.S. waste-to-energy companies in the last three decades. U.S. companies have made U.S. waste-ta energy plants the least costly and most efficient plants in the world. U.S. waste-to-energy companies may or medicated? An understanding of how a global economy impacts the marketing of U.S. waste-ta-energy services

Columbia University

42

EA-0952: The Louisiana State University Waste-to Energy Incinerator, Baton  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2: The Louisiana State University Waste-to Energy 2: The Louisiana State University Waste-to Energy Incinerator, Baton Rouge, Louisiana EA-0952: The Louisiana State University Waste-to Energy Incinerator, Baton Rouge, Louisiana SUMMARY This EA evaluates the environmental impacts of the proposal for incinerating combustible, non-recyclable office wastes from Louisiana State University (LSU) administrative/academic areas and combustible, non-renderable biological and potentially infectious wastes from the School of Veterinary Medicine and Student Health Center, both part of the LSU campus complex in Baton Rouge, Louisiana. PUBLIC COMMENT OPPORTUNITIES None available at this time. DOCUMENTS AVAILABLE FOR DOWNLOAD October 24, 1994 EA-0952: Finding of No Significant Impact The Louisiana State University Waste-to Energy Incinerator

43

MacArthur Waste to Energy Facility Biomass Facility | Open Energy  

Open Energy Info (EERE)

MacArthur Waste to Energy Facility Biomass Facility MacArthur Waste to Energy Facility Biomass Facility Jump to: navigation, search Name MacArthur Waste to Energy Facility Biomass Facility Facility MacArthur Waste to Energy Facility Sector Biomass Facility Type Municipal Solid Waste Location Suffolk County, New York Coordinates 40.9848784°, -72.6151169° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":40.9848784,"lon":-72.6151169,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

44

Fuel Cell Technologies Office: Waste-to-Energy using Fuel Cells...  

NLE Websites -- All DOE Office Websites (Extended Search)

of Defense (DOD) held a webinar on July 13, 2011, in Washington, DC, to discuss waste-to-energy for fuel cell applications. Presentations DOD-DOE MOU WTE Using Fuel Cells...

45

Fuel Cell Technologies Office: Waste-to-Energy using Fuel Cells...  

NLE Websites -- All DOE Office Websites (Extended Search)

of Defense (DOD) held a workshop on January 13, 2011, in Washington, DC, to discuss waste-to-energy and fuel cell use. Workshop objectives were to (1) identify DOD-DOE...

46

Waste-to-Energy Technologies and Project Development  

NLE Websites -- All DOE Office Websites (Extended Search)

chemicals, synthetic diesel (development) *Torrefied wood for pellets, coal replacement *Pyrolysis oil for boilers and power (early commercial) * Specialty chemicals (commercial)...

47

Waste-to-Energy Projects at Army Installations  

NLE Websites -- All DOE Office Websites (Extended Search)

integrated with microturbine steam generator Others Fort Stewart 94,000 lbshr steam Wood Chip Plant (off line). Aberdeen Proving Ground - Offsite plant supplies approx...

48

Waste-to-Energy Biomass Digester with Decreased Water Consumption  

The enormous amount of biomass waste created by animal feeding operations releases methane, a valuable fuel but also a greenhouse gas, and other pollutants into the environment. Waste digesters reduce this pollution by converting the waste into ...

49

EA-1862: Oneida Seven Generation Corporation Waste-To-Energy System,  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

62: Oneida Seven Generation Corporation Waste-To-Energy 62: Oneida Seven Generation Corporation Waste-To-Energy System, Ashwaubenon, Wisconsin EA-1862: Oneida Seven Generation Corporation Waste-To-Energy System, Ashwaubenon, Wisconsin Summary This EA evaluates the environmental impacts of a proposal by Oneida's Energy Recovery Project to construct and operate a solid waste-to-electricity power plant on vacant property within the Bayport Industrial Center in the City of Green Bay, Brown County, Wisconsin. This energy recovery process would involve bringing municipal solid waste into the plant for sizing (shredding), sorting (removing recyclable material), and conveying into one of three pyrolytic gasification systems. Public Comment Opportunities No public comment opportunities available at this time. Documents Available for Download

50

12th North American Waste to Energy Conference May 17-19, 2004, Savannah, Georgia USA  

E-Print Network (OSTI)

the generation of electrical energy from those fractions of wastes that cannot be economically reused or recycled-established computational fluid dynamic codes (CFD). Previously, there has not been available a validated, comprehensive12th North American Waste to Energy Conference May 17-19, 2004, Savannah, Georgia USA NAWTEC12

Columbia University

51

10/12/2009 www.wtert.gr 1 Waste-to-Energy Research and Technology Council  

E-Print Network (OSTI)

management Conservation of the precious Greek land for future usage Empowerment of the energy balance10/12/2009 www.wtert.gr 1 Waste-to-Energy Research and Technology Council SYNERGIA Dr. Efstratios MANAGEMENT IN GREECE & POTENTIAL FOR WASTE - TO - ENERGY ISWA Beacon Conference - Strategic Waste Management

Columbia University

52

15th North American Waste to Energy Conference May 21-23, 2007, Miami, Florida USA  

E-Print Network (OSTI)

15th North American Waste to Energy Conference May 21-23, 2007, Miami, Florida USA NAWTEC15 Technology Officer, Von Roil inova Alfred Sigg, Head of Research & Development, Von Roil inova Abstract: Von further treatment. In instances where extremely high contaminant loadings are expected (usually due

Columbia University

53

CEWEP -Confederation of European Waste-to-Energy Plants Boulevard Clovis 12A  

E-Print Network (OSTI)

follow at a distance, are energy from Landfill Gas (LFG) extraction, co-incineration of SRF (Solid; BEP ­ Biomass Energy Plants; LFG ­ Landfill Gas; WtE ­ Waste-to-Energy 1 Excluding agricultural policy would be even more ambitious, replacing landfilling). Both the supply of renewable electricity

54

The Current and Future Marketplace for Waste-To-Energy Cogeneration Facilities in the United States  

E-Print Network (OSTI)

The emerging waste-to-energy marketplace within the United States is one with considerable opportunity and risk. The solid waste management crisis is resulting in record construction levels for waste-to-energy facilities due to the fact that few viable alternatives exist for waste disposal. However, opposition to the construction of such plants and cost overruns on new and existing facilities is having an impact on the market. While approximately 135 plants were operating at the end of 1987, it is believed that 425 plants and projects will be in existence by the end of 1996. Representing a total capacity of 260,000 tons per day, by 1996 over 36% of all municipal solid waste generated in the United States will be incinerated by waste-to-energy facilities. A considerable challenge faces all suppliers of products and services to the marketplace. Increasing opposition and escalating costs for such plants will place greater emphasis upon proper planning, design flexibility, and pollution control. Like any emerging industry, this business will evolve from its current unpredictable levels to a more mature and stable market opportunity for suppliers of products and services.

Jacobs, S.

1988-09-01T23:59:59.000Z

55

T:\\013.ffentlichkeitsarbeit\\05.Vortrge\\32.NAWTEC 11 Florida 2003\\A_Ways to Improve the Efficiency of Waste to Energy Plants.doc Ways to Improve the Efficiency of Waste to Energy Plants  

E-Print Network (OSTI)

@mvr-hh.de Abstract Up to now the emissions of waste-to-energy plants have been of major concern for the operators. There is also legislation in the pipeline restricting landfilling of untreated waste. In view of the discussions in mind the recovery rate of reusable materials from the incineration of waste or flue gas treatment

Columbia University

56

The potential for use of waste-to-energy facility ash: Executive summary. Final report  

DOE Green Energy (OSTI)

This executive summary presents an overview of the investigations, findings, conclusions, and recommendations of the Long Island Regional Planning Board (LIRPB) study of the Potential for Beneficial Use of Waste-to-Energy Facility Ash. The full report consists of the following volumes: Executive Summary; Volume 1: Long Island Ash Management Status; Volume 2: Sampling and Testing Procedures; Volume 3: Environmental Properties; Volume 4: Engineering Properties; Volume 5: Environmental Assessment; Volume 6: Engineering and Economic Evaluation; and Volume 7: Legal and Institutional Issues. Volumes one through seven are briefly summarized in this executive summary with the exception of Volume 2 of the report, which serves as the documentation of the sampling conditions and testing methods used in measuring chemical and physical properties of the ash tested. The study investigated the feasibility of the use of incinerator ash as a substitute for natural aggregate in construction applications.

Koppelman, L.E.; Tanenbaum, E.G. [Long Island Regional Planning Board, Hauppauge, NY (United States)

1994-05-01T23:59:59.000Z

57

Impact of Flow Control and Tax Reform on Ownership and Growth in the U.S. Waste-to-Energy Industry  

Reports and Publications (EIA)

This article analyzes two key issues that could be influencing growth and ownership (both public and private) in the Waste To Energy (WTE) industry.

Information Center

1994-09-01T23:59:59.000Z

58

15th North American Waste to Energy Conference May May 21-23, 2007, Miami, Florida USA  

E-Print Network (OSTI)

% of· cooling towers at any time, even with normal water treatment programs in place. This could pose a risk to employees and others working near cooling towers, and it could pose a risk to neighboring for waste-to-energy facility cooling towers. While a corporate policy for managing the risk due to Legiolle

Columbia University

59

Digital Gas Joins Asian Waste-to-Energy Consortium: To Eliminate Coal as a Power Plant Fuel  

E-Print Network (OSTI)

Digital Gas Joins Asian Waste-to-Energy Consortium: To Eliminate Coal as a Power Plant Fuel Digital upside in view of the power generation growth potential in Asia and the environmental friendly, cost's energy and farming centers in North America as an alternative to coal-fired power plants and a solution

Columbia University

60

Integrated assessment of a new Waste-to-Energy facility in Central Greece in the context of regional perspectives  

Science Conference Proceedings (OSTI)

The main aim of this study is the integrated assessment of a proposed Waste-to-Energy facility that could contribute in the Municipal Solid Waste Management system of the Region of Central Greece. In the context of this paper alternative transfer schemes for supplying the candidate facility were assessed considering local conditions and economical criteria. A mixed-integer linear programming model was applied for the determination of optimum locations of Transfer Stations for an efficient supplying chain between the waste producers and the Waste-to-Energy facility. Moreover different Regional Waste Management Scenarios were assessed against multiple criteria, via the Multi Criteria Decision Making method ELECTRE III. The chosen criteria were total cost, Biodegradable Municipal Waste diversion from landfill, energy recovery and Greenhouse Gas emissions and the analysis demonstrated that a Waste Management Scenario based on a Waste-to-Energy plant with an adjacent landfill for disposal of the residues would be the best performing option for the Region, depending however on the priorities of the decision makers. In addition the study demonstrated that efficient planning is necessary and the case of three sanitary landfills operating in parallel with the WtE plant in the study area should be avoided. Moreover alternative cases of energy recovery of the candidate Waste-to-Energy facility were evaluated against the requirements of the new European Commission Directive on waste in order for the facility to be recognized as recovery operation. The latter issue is of high significance and the decision makers in European Union countries should take it into account from now on, in order to plan and implement facilities that recover energy efficiently. Finally a sensitivity check was performed in order to evaluate the effects of increased recycling rate, on the calorific value of treated Municipal Solid Waste and the gate fee of the candidate plant and found that increased recycling efforts would not diminish the potential for incineration with energy recovery from waste and neither would have adverse impacts on the gate fee of the Waste-to-Energy plant. In general, the study highlighted the need for efficient planning in solid waste management, by taking into account multiple criteria and parameters and utilizing relevant tools and methodologies into this context.

Perkoulidis, G. [Laboratory of Heat Transfer and Environmental Engineering, Department of Mechanical Engineering, Aristotle University of Thessaloniki, Box 483, GR-54124 Thessaloniki (Greece); Papageorgiou, A., E-mail: giou6@yahoo.g [Laboratory of Heat Transfer and Environmental Engineering, Department of Mechanical Engineering, Aristotle University of Thessaloniki, Box 483, GR-54124 Thessaloniki (Greece); Karagiannidis, A. [Laboratory of Heat Transfer and Environmental Engineering, Department of Mechanical Engineering, Aristotle University of Thessaloniki, Box 483, GR-54124 Thessaloniki (Greece); Kalogirou, S. [Waste to Energy Research and Technology Council (Greece)

2010-07-15T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Retrofit of waste-to-energy facilities equipped with electrostatic precipitators. Volume I: Report  

Science Conference Proceedings (OSTI)

To help lower the cost of compliance for waste-to-energy facilities, a retrofit technology using water spray temperature reduction combined with dry acid gas control reagent and powdered activated carbon [PAC] injection was tested in November, 1995 as part of an American Society of Mechanical Engineers' [ASME] Center for Research and Technology Development [CRTD] effort supported in part by the Department of Energy's National Renewable Energy Laboratory [NREL] and directed by the ASME Research Committee on Industrial and Municipal Waste. 2,000 mg/dsm{sup 3} @ 7% O{sub 2} (150 lb/hr) of trona (a natural sodium sesquicarbonate ore) injected through a rapid dispersion lance successfully controlled more than 50 percent of the acid gases. This should let facilities under 250 TPD meet the small plant guidelines for acid gas control. Various levels of PAC were injected along with the trona. 300 mg/dsm{sup 3} 7% O{sub 2} of PAC provides a comfortable margin between the emissions limitations achieved and both large and small plant regulatory guidelines for tetra- through octachlorinated dibenzo-p-dioxins and dibenzofurans [PCDD/F] and mercury when the ESP is operated below 350 F. Bi-fluid nozzles were used to spray finely atomized water between the economizer outlet and ESP inlet to maintain temperatures in the desired 300-350 F range. Particulate and metals emissions limitations were met by this 400 ft{sup 2}/1,000 acft{sup 2} specific collector area [SCA], 3-field ESP. Both the water sprays and PAC improved ESP performance. The demonstration was successful. With dry PAC, acid gas reagent injection, and temperature reduction, MWC emissions guidelines for facilities smaller than 250 TPD can be reliably met. Everything except the large facilities SO{sub 2} and HCl guideline emissions limitations was achieved. Better acid gas control should be achievable with more reagent addition if the ESP is efficient enough to avoid violating particulate limits.

Rigo, H.G. [Rigo & Rigo Associates, Inc., Berea, OH (US); Chandler, A.J. [A.J. Chandler & Associates, Ltd., Toronto, Ontario (Canada)

1996-04-01T23:59:59.000Z

62

Long-term affected energy production of waste to energy technologies identified by use of energy system analysis  

Science Conference Proceedings (OSTI)

Affected energy production is often decisive for the outcome of consequential life-cycle assessments when comparing the potential environmental impact of products or services. Affected energy production is however difficult to determine. In this article the future long-term affected energy production is identified by use of energy system analysis. The focus is on different uses of waste for energy production. The Waste-to-Energy technologies analysed include co-combustion of coal and waste, anaerobic digestion and thermal gasification. The analysis is based on optimization of both investments and production of electricity, district heating and bio-fuel in a future possible energy system in 2025 in the countries of the Northern European electricity market (Denmark, Norway, Sweden, Finland and Germany). Scenarios with different CO{sub 2} quota costs are analysed. It is demonstrated that the waste incineration continues to treat the largest amount of waste. Investments in new waste incineration capacity may, however, be superseded by investments in new Waste-to-Energy technologies, particularly those utilising sorted fractions such as organic waste and refuse derived fuel. The changed use of waste proves to always affect a combination of technologies. What is affected varies among the different Waste-to-Energy technologies and is furthermore dependent on the CO{sub 2} quota costs and on the geographical scope. The necessity for investments in flexibility measures varies with the different technologies such as storage of heat and waste as well as expansion of district heating networks. Finally, inflexible technologies such as nuclear power plants are shown to be affected.

Muenster, M., E-mail: maem@risoe.dtu.d [Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, Frederiksborgvej 399, 4000 Roskilde (Denmark); Meibom, P. [Risoe National Laboratory for Sustainable Energy, Technical University of Denmark, Frederiksborgvej 399, 4000 Roskilde (Denmark)

2010-12-15T23:59:59.000Z

63

Financing options for projects converting forestry and farm wastes to energy  

DOE Green Energy (OSTI)

A significant barrier to increased use of wastes and residues as fuel by small- and medium-sized industries is financing of projects. This document covers governmental and private sector financing options available to prospective users of wood residues and agricultural wastes for industrial applications-direct combustion, steam generation, or cogeneration. This guide contains four major sections. Section I provides brief descriptions of the type of project financing options available to industry through private sector sources. This section is not intended to provide the level of detailed information required to make a final determination of the best source of private sector financing for a particular company or organization. It does, however, present a concise review of the options available on which more detailed study can be based. Section II introduces the availability of assistance for specific types of projects from federal, state, and several municipalities. Section III presents two case studies of costs, annual savings, return on investment, and payback periods for these projects, as well as the affects of depreciation, taxes, tax credits and sale of excess power. All facts and figures were supplied by the individual companies or by their engineering consulting firms. A checklist for decisions concerning bioenergy projects, as well as addresses and contacts in regional government agency offices involved in providing financial assistance, are included in the final section.

Farley, R.C.; Parker, S.K.; Hodam, R.

1980-07-01T23:59:59.000Z

64

Urban Wood Waste Resource Assessment  

DOE Green Energy (OSTI)

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

Wiltsee, G.

1998-11-20T23:59:59.000Z

65

13th North American Waste to Energy Conference May 23-25, 2005, Orlando, Florida USA  

E-Print Network (OSTI)

that can use blue stained wood and wood pellets (beyond pellet fuel) · The area of value-added products Facilities- no specific goals or incentives Federal · Dedicated biomass power vs co-firing and Production Tax-firing with coal- 456 MW Hayden Sawmill- CHP Biomass Power- 45 MWe WoodChipsGT/Year Larger Scale Biomass Heat/CHP/Co-firing/Power

Columbia University

66

Report of the DOD-DOE Workshop on Converting Waste to Energy...  

NLE Websites -- All DOE Office Websites (Extended Search)

plants (WWTPs) and landfills, food waste (such as spent cooking oil from mess halls), compost heaps, plastic waste, and paper waste (office paper and cardboard). DOD may also be...

67

Ris DTU 09-06-08 Waste-to-energy technologies in TIMES models  

E-Print Network (OSTI)

-to-energy technologies in the Pan-European NEEDS- TIMES model Waste incineration for electricity and heat, landfill gas legislation on waste Directives · Waste Framework Directive, 1975 (75/442/EEC) · Directive on the landfill be accepted as recovery) Avoid · Landfill #12;Risø DTU 09-06-08 4 European waste model Econometric model

68

Copyright ASME 20091 Proceedings of the 17th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

procedure for estimating costs for industrial, on-site, waste gasification processes. However, gen eralizingECONOMICS OF ON-SITE WASTE GASIFICATION ALFRED C. W. EGGEN K. T. Lear Associates. Inc. Manchester, Charles R Velzy Associates, Inc., Elmsford, N.Y. On-site waste gasification may well be an at tractive

Columbia University

69

European waste-to-energy systems: case study of Geneva-Cheneviers (Switzerland)  

DOE Green Energy (OSTI)

The City of Geneva, population 159,000 is the administrative center of the Canton of Geneva, population 340,000. The Canton owns a number of facilities for the treatment of waste. Geneva's chief waste treatment facility is the Cheneviers Incinerator. Two Von Roll integrated boiler incinerator furnaces have a rated capacity of 200 metric tons (220 short tons) per day each. Superheated steam at 360/sup 0/C and 32.4 bars (32 atm) powers a 6200 kW turbo-generator unit. The electricity is sold to the cantonal grid. Total incinerable waste in the Canton of Geneva has varied from 120,000 to 130,000 metric tons (132,000 to 144,000 short tons) annually during the last five years. For the last two years, total per capita tonnage have been declining. Per capita incinerable waste was 363 kilograms (800 lbs) in the year 1975, of which 257 kilograms (606 lbs) were household waste. Eighty-seven thousand, five hundred metric tons (96,386 short tons) of this waste was burned in the Cheneviers Incinerator in 1975. The remainder was landfilled, due to the lack of capacity at the incinerators. The system which began operating in 1966, cost approximately 40 million Swiss Francs ($9.3 million; 1965 or $23 million; 1976). Three-quarters of this sum was for land, buildings, construction, and equipment. A large station and dock for the transfer of waste accounted for the remainder. The Von Roll design ofthis plant is now out of date. Extensive modifications were made to correct corrosion problems in the furnace.

None

1977-05-01T23:59:59.000Z

70

COMBINED HEAT AND POWER FOR A COLLEGE CAMPUS THE HARRISONBURG, VIRGINIA WASTE-TO-ENERGY FACILITY  

E-Print Network (OSTI)

of installing the super-heaters, cooling towers, condensers and auxiliary equipment needed to make and cooling needs of the campus. This facility also has a small turbine that can be brought on line to produce Madison University central heating & cooling system. This facility uses a mass-burn style waste combustion

Columbia University

71

Proceedings of NAWTEC16 16th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

's average per capita waste generation rate is 0.18 tonnes per person. Although the reported collection and there is a market for the electricity generated by the WTE facility. The main problem to overcome is the source historically been a driver of economic growth not only for the state of Maharashtra, of which it is the capital

Columbia University

72

9th Annual North American Waste to Energy Conference Ash Recycling: Partnering for Progress  

E-Print Network (OSTI)

Townships as the host municipalities, PennDOT as a potential major end-user, MYRES as the RRC opaator the RRC's ash. After exhaustive research, YCSWA selected AAR's technology and commWlicated those benefits Center (RRC) in Manchester Township, Pennsylvania; and owns and operates the Yard Waste Compot Site

Columbia University

73

Proceedings of NAWTEC17 17th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

Luxembourg 0.29 673a 21 US 226 730 56 Japan 52.4 412 7 a Estimate Table 2 shows the increase in the amount 11.48 Luxembourg 591 673a 13.87 US 736 730 -1.0 Japan 407 412 1.0 a Estimated for the year based received' MSW followed by a range of waste manipulation processes gasification and pyrolysis ­ flexible

Columbia University

74

An integrated analytical framework for quantifying the LCOE of waste-to-energy facilities for a range of greenhouse gas emissions policy and technical factors  

SciTech Connect

This study presents a novel integrated method for considering the economics of waste-to-energy (WTE) facilities with priced greenhouse gas (GHG) emissions based upon technical and economic characteristics of the WTE facility, MSW stream, landfill alternative, and GHG emissions policy. The study demonstrates use of the formulation for six different policy scenarios and explores sensitivity of the results to ranges of certain technical parameters as found in existing literature. The study shows that details of the GHG emissions regulations have large impact on the levelized cost of energy (LCOE) of WTE and that GHG regulations can either increase or decrease the LCOE of WTE depending on policy choices regarding biogenic fractions from combusted waste and emissions from landfills. Important policy considerations are the fraction of the carbon emissions that are priced (i.e. all emissions versus only non-biogenic emissions), whether emissions credits are allowed due to reducing fugitive landfill gas emissions, whether biogenic carbon sequestration in landfills is credited against landfill emissions, and the effectiveness of the landfill gas recovery system where waste would otherwise have been buried. The default landfill gas recovery system effectiveness assumed by much of the industry yields GHG offsets that are very close to the direct non-biogenic GHG emissions from a WTE facility, meaning that small changes in the recovery effectiveness cause relatively larger changes in the emissions factor of the WTE facility. Finally, the economics of WTE are dependent on the MSW stream composition, with paper and wood being advantageous, metal and glass being disadvantageous, and plastics, food, and yard waste being either advantageous or disadvantageous depending upon the avoided tipping fee and the GHG emissions price.

Townsend, Aaron K., E-mail: aarontownsend@utexas.edu [Department of Mechanical Engineering, University of Texas at Austin, 1 University Station C2200, Austin, TX 78712 (United States); Webber, Michael E. [Department of Mechanical Engineering, University of Texas at Austin, 1 University Station C2200, Austin, TX 78712 (United States)

2012-07-15T23:59:59.000Z

75

Evaluation of the impact of RCRA amendments on waste-to-energy activities by using a system simulation computer code  

DOE Green Energy (OSTI)

The primary methodology that is used for disposal of municipal solid waste is the use of land fills; 80--85% of the municipal solid waste (MSW) produced in the country currently is land filled. The two other disposal alternatives used are recycling and incineration. Waste-to-energy technology (WTE) which incinerates MSW to produce electricity and/or steam is attractive in other cases since it reduces landfill volume, reduces the consumption of fossil and other fuels, and produces a revenue stream from the sale of the electricity or steam. The gaseous effluents from landfills can also be used to fuel power plants. Recycling and material separation programs can have a substantial impact on the throughput and heating value of MSW collected and thus impact WTE plant economics; the magnitude of the impact will depend upon a number of factors such as what materials and what fraction are separated and recycled, the design of the WTE plant itself (its operating window); the contractual arrangements relative to maintaining throughput (ability to adjust catchment area), limitations on adjusting tipping fees, etc. Mandated increased recycling and landfill gaseous effluent control -- could alter substantially the economics and competitive position of the MSW-WTE industry. The objectives of this study are: (1) to simulate typical WTE plants fired with a national average waste stream, (2) to evaluate the parametric effects of waste component recycling on the performance of the typical WTE plants, and (3) to assess the impact of RCRA recycling amendments on the performance of the typical WTE plants and on the potential methane generation of typical landfills. The relevant technical issues, technical approach, results and conclusions are presented.

Chang, S.L.; Petrick, M.; Stodolsky, F.; Freckmann, A.B.

1994-09-01T23:59:59.000Z

76

Retrofit of waste-to-energy facilities equipped with electrostatic precipitators. Volume III: Test protocol  

DOE Green Energy (OSTI)

The American Society of Mechanical Engineers' [ASME] Center for Research and Technology Development [CRTD] has been awarded a subcontract by the National Renewable Energy Laboratory [NREL] to demonstrate the technical performance and viability of flue gas temperature control in combination with dry acid gas reagent and activated carbon injection at an existing electrostatic precipitator [ESP] equipped municipal waste combustor [MWC]. The objective of this proof-of-concept demonstration test is to economically and reliably meet 40 CFR 60 Subpart Cb Emissions Guidelines for MWC's at existing ESP equipped facilities. The effort is being directed by a Subcommittee of tile ASME Research Committee on Industrial and Municipal Wastes [RCIMW] chaired by Dave Hoecke. Mr. Greg Barthold of ASME/CRTD is the Project Manager. ASME/CRTD contracted with Rigo & Rigo Associates, Inc. in cooperation with A.J. Chandler & Associates, Ltd. to be the Principal Investigator for the project and manage the day-t o-day aspects of the program, conduct the testing reduce and interpret the data and prepare the report. Testing will be conducted at the 2 by 210 TPD, ESP equipped MWC at the Davis County Resource Recovery Facility in Layton, Utah. The test plan calls for duplicate metals (Cd, Pb and Hg), dioxin and acid gas runs.

Rigo, H.G. [Rigo & Rigo Associates, Inc., Berea, OH (US); Chandler, A.J. [A.J. Chandler & Associates, Inc., Toronto, Ontario (Canada)

1996-04-01T23:59:59.000Z

77

Retrofit of waste-to-energy facilities equipped with electrostatic precipitators. Volume II: Field and laboratory reports, Part 2 of 2  

DOE Green Energy (OSTI)

Volume II (part 2 of 2) of ''Retrofit of Waste-to-energy Facilities Equipped with Electrostatic Precipitators'' contains the field and laboratory reports, including: (1) field reports, (2) analytic laboratory reports, (3) chain of custody forms, and (4) TCLP laboratory reports.

Rigo, H.G. [Rigo & Rigo Associates, Inc., Berea, OH (US); Chandler, A.J. [A.J. Chandler & Associates, Ltd., Toronto, Ontario (Canada)

1996-04-01T23:59:59.000Z

78

Retrofit of waste-to-energy facilities equipped with electrostatic precipitators. Volume II: Field and Laboratory Reports, Part 1 of 2  

DOE Green Energy (OSTI)

Volume II (part 1 of 2) of ''Retrofit of Waste-to-energy Facilities Equipped with Electrostatic Precipitators'' contains the documentation and raw data, including: (1) field reports, (2) analytic laboratory reports, (3) chain of custody forms, and (4) TCLP laboratory reports.

Rigo, H.G. [Rigo & Rigo Associates, Inc., Berea, OH (US); Chandler, A.J. [A.J. Chandler & Associates, Ltd., Toronto, Ontario (Canada)

1996-04-01T23:59:59.000Z

79

Waste Not, Want Not: Analyzing the Economic and Environmental Viability of Waste-to-Energy (WTE) Technology for Site-Specific Optimization of Renewable Energy Options  

Science Conference Proceedings (OSTI)

Waste-to-energy (WTE) technology burns municipal solid waste (MSW) in an environmentally safe combustion system to generate electricity, provide district heat, and reduce the need for landfill disposal. While this technology has gained acceptance in Europe, it has yet to be commonly recognized as an option in the United States. Section 1 of this report provides an overview of WTE as a renewable energy technology and describes a high-level model developed to assess the feasibility of WTE at a site. Section 2 reviews results from previous life cycle assessment (LCA) studies of WTE, and then uses an LCA inventory tool to perform a screening-level analysis of cost, net energy production, greenhouse gas (GHG) emissions, and conventional air pollution impacts of WTE for residual MSW in Boulder, Colorado. Section 3 of this report describes the federal regulations that govern the permitting, monitoring, and operating practices of MSW combustors and provides emissions limits for WTE projects.

Funk, K.; Milford, J.; Simpkins, T.

2013-02-01T23:59:59.000Z

80

Table F24: Wood and Biomass Waste Consumption Estimates, 2011  

U.S. Energy Information Administration (EIA)

Table F24: Wood and Biomass Waste Consumption Estimates, 2011 State Wood Wood and Biomass Waste a Residential Commercial Industrial Electric Power ...

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Biomass Energy - Focus on Wood Waste  

NLE Websites -- All DOE Office Websites (Extended Search)

application for wood waste as a fuel is in the co-firing of conventional coal-fired boilers, which means using biomass as a supplementary energy source in high- efficiency...

82

Proceedings of the 17th Annual North American Waste-to-Energy Conference May 18-20, 2009, Chantilly, Virginia, USA  

E-Print Network (OSTI)

.; Mondragon, F., CO2 strong chemisorption as an estimate of coal char gasification reactivity. Fuel 1999, 78 WASTE (MSW) GASIFICATION UNDER VARIOUS PRESSURES AND CO2 CONCENTRATION ATMOSPHERES Eilhann Kwon, Kelly J, New York, NY 10027 ABSTRACT The Municipal Solid Waste (MSW) gasification process is a promising

Columbia University

83

An assessment of management practices of wood and wood-related wastes in the urban environment  

DOE Green Energy (OSTI)

The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

NONE

1996-02-01T23:59:59.000Z

84

Furniture wood wastes: Experimental property characterisation and burning tests  

Science Conference Proceedings (OSTI)

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg{sup -1} for HHV, and from 3304 to 4634 kcal kg{sup -1} for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM{sub 1} fraction during incomplete industrial wood burning.

Tatano, Fabio [Faculty of Sciences and Technologies, University of Urbino 'Carlo Bo', Campus Scientifico - Sogesta, 61029 Urbino (Italy)], E-mail: fabio.tatano@uniurb.it; Barbadoro, Luca; Mangani, Giovanna; Pretelli, Silvia; Tombari, Lucia; Mangani, Filippo [Faculty of Sciences and Technologies, University of Urbino 'Carlo Bo', Campus Scientifico - Sogesta, 61029 Urbino (Italy)

2009-10-15T23:59:59.000Z

85

FEASIBILITY ANALYSIS OF WASTE-TO-ENERGY  

E-Print Network (OSTI)

oxygen protection. Several journal articles and conference proceedings provide design details regarding of the cabling and fault-detection circuitry. Power scavenging concepts may also be considered for low photolithography combined with hydrofluoric acid wet chemical etching, chlorine-based plasma etching or CFB4

Columbia University

86

Waste-to-Energy Design Proposal for  

E-Print Network (OSTI)

of various arsenicals has led to extensive contamination of groundwater in the US (Smith et al., 1998). High transformations of arsenic and iron in water treatment sludge during aging and TCLP extraction. Environ. Sci

Columbia University

87

Improved Process control of wood waste fired boilers  

DOE Green Energy (OSTI)

This project's principal aim was the conceptual and feasibility stage development of improved process control methods for wood-waste-fired water-tube boilers operating in industrial manufacturing applications (primarily pulp and paper). The specific objectives put forth in the original project proposal were as follows: (1) fully characterize the wood-waste boiler control inter-relationships and constraints through data collection and analysis; (2) design an improved control architecture; (3) develop and test an appropriate control and optimization algorithm; and (4) develop and test a procedure for reproducing the approach and deriving the benefits on similar pulp and paper wood-waste boilers. Detailed tasks were developed supporting these objectives.

Process Control Solutions, Inc.

2004-01-30T23:59:59.000Z

88

9th Annual North American Waste to Energy Conference WASTE TO ENERGY PLANT  

E-Print Network (OSTI)

alternatives to use of gaseous chlorine for cooling tower treatment. SOLUTION: Our water treatment consultant the effectiveness of the treatment and liability concerns. Because we run our COOling towers at a pH of B.O-B.5 for the ash ram extractors for cooling, and to the fly ash pug mill. We also realized that our high sewer

Columbia University

89

Waste-to-Energy Projects at ArmyWaste to Energy Projects at Army Installations  

E-Print Network (OSTI)

13 JAN 201113 JAN 2011 US Army Corps of Engineers BUILDING STRONG® Distribution Statement A -- Approved for public release; distribution is unlimited. #12;Outline Background Intro to ERDC Army natural gas and steam by Oct 2016 [EISA 2007] Electricity use for federal government from renewable

90

Chemical Pretreatment And Enzymatic Hydrolysis Of Mixed Source-Separated Organic (SSO) And Wood Waste.  

E-Print Network (OSTI)

??This paper examines the effectiveness of two pretreatments on Source-Separated Organic waste (SSO) mixed with wood wastes: long term lime for SSO mixed with forestry (more)

Faye, Michael

2010-01-01T23:59:59.000Z

91

Waste Growth Challenges Local Democracy. The Politics of Waste between Europe and the Mediterranean: a Focus on Italy  

E-Print Network (OSTI)

The new incinerator (or waste-to-energy plant) in the Alpinedecreasing. Indeed waste-to- energy plants and recyclingDerived Fuel) and sent to a waste-to- energy plants, are now

Mengozzi, Alessandro

2010-01-01T23:59:59.000Z

92

An Economic Assessment of Market-Based Approaches to Regulating the Municipal Solid Waste Stream  

E-Print Network (OSTI)

generation of biofuel waste energy and increases the rate ofthe design and siting of waste to energy incinerators. Theregion is burned in waste-to-energy incineration facilities.

Menell, Peter S.

2004-01-01T23:59:59.000Z

93

FIRE PROTECTION DESIGN CONSIDERATIONS FOR WASTE-TO-ENERGY FACILITIES  

E-Print Network (OSTI)

. COOLING TOWERS Unless the cooling tower is constructed only of non combustible material, it should "Water Cooling Tower". For medium and large resource re covery facilities, the cooling tower system. For larger cooling towers, 20 min fire-resistant par titions that separate the cells would further minimize

Columbia University

94

EIA Energy Kids - Covanta Waste-to-Energy Plant  

U.S. Energy Information Administration (EIA)

Natural Gas; Nuclear; Oil (petroleum) Photovoltaic; Solar Thermal; Transportation; Wind; ... This means that Covanta takes garbage and turns it into electricity. Cool.

95

The 2010 ERC Directory of Waste-to-Energy Plants  

E-Print Network (OSTI)

stream would have increased the overall thermal efficiency by another 10%. 3. U.S. EPA, eGrid 2007.gov/cleanenergy/energy-resources/ egrid/index.html. (Accessed February 13, 2009.) 4. Personal communication with Joseph Staniunas, UTC

Columbia University

96

(Continued on page 2) Waste-to-Energy Technologies  

E-Print Network (OSTI)

of 7700 Btu/lb University of Iowa Main Power Plant's Boiler 10 A boiler unit rated at 170,000 lb/h steam-fireB Averages 61.3 ± 0.7 0.0060 ± 0.003 131 ± 4 % DifferenceC -17.7% -81.2% -18.3 Iowa Main Power Plant's Boiler value (LHV) of the gas by 8.5%, from 569 British thermal units per standard cubic foot (Btu/scf) to 617

97

Microsoft Word - Oneida Waste to Energy Project DOE Final EA...  

NLE Websites -- All DOE Office Websites (Extended Search)

with an array of industries. Oneida applied for SEP funding under Wisconsin's "Job Creation and Retention through Clean Energy Advanced Manufacturing." Wisconsin determined that...

98

EFFECTS OF MATERIALS RECOVERY WASTE-TO-ENERGY CO  

E-Print Network (OSTI)

met 'Multinational Nuclear Approach' MNP Milieu en Natuur Planbureau MOX Mixed oxide fuel, aanduiding

Columbia University

99

Waste-to-Energy Biomass Digester with Decreased Water Consumption  

energy costs. Anaerobic digesters work by allowing bacteria to break down the ... water is scarce, and helps to reduce the environmental impact of ...

100

Waste-to-Energy Biomass Digester with Decreased Water Consumption  

Patent Informationreleases methane, a valuable fuel but also a greenhouse gas, and other pollu-Patent Pending; U. S. Provisional

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

CONSOLIDATED DATA BASE FOR WASTE-TO-ENERGY PLANT EMISSIONS  

E-Print Network (OSTI)

in northern England and Scotland. 4. Large scale generation and co-firing Biomass has a potentially significant role to play in co-firing and large scale generation. However, the location of current plants in providing co-firing supply. Particular sensitivities relevant to this are being explored elsewhere

Columbia University

102

Wood Waste -A Modern Fuel M. A. SERRELL, P. E.  

E-Print Network (OSTI)

, designed like the vanes of a fan WOOD BO'LER SACK r-v'"",", __--J DAMF[R · I ... .... .... .... ... ... FAN and provides automatic steam generation on an unattended basis. A flyash arrestor with induced draft fan fashioned boiler design where the boiler shell is pierced by a number of longitudinal fire tubes which run

Columbia University

103

Characterization of Waste Tar Associated with Abandoned Wood Chemical Plant Sites in Northwest Pennsylvania, USA  

SciTech Connect

Over 70 wood chemical plants operated in northern Pennsylvania between ca. 1890 and 1950, all located within 72 km of the New York state border. Their original purpose was to salvage the small unwanted hardwood trees left behind by the lumber mills, and to make charcoal, calcium acetate and methanol for a number of industrial uses via destructive distillation. At many old wood chemical plant sites, unknown quantities of wood tar remain as a residual contaminant and pose a pollution threat to aquatic life in nearby streams. Research on the composition and properties of residual wood tars from five abandoned industrial sites in Pennsylvania are described. Weathered wood tars were more viscous and contained fewer volatile and semivolatile organic compounds than did soil-buried tars. Phenol, 2-methylphenol (o-cresol), 4-methylphenol (p-cresol), and 2, 4-dimethylphenol were found in all sampled tars. These water-soluble phenolic compounds were released quasi-instantaneously in aqueous solution, followed by a slower rate of release, consistent with the behavior of similar compounds in other dense non-aqueous liquids. Air-exposed wood tar deposits developed a hard crust, which contained fewer volatiles and semivolatiles and had a higher softening point than other samples. These tars eroded to form a powdered soil colonized by lichens and mosses. Residual wood tar material found at one site was shown to be thermally altered, likely during the historical destruction of the chemical plant by fire. Recovered wood tar wastes have a relatively high heating value and may have use as a potential, but limited, alternate energy source.

Edendorn, H.M.; Severson, D. (Allegheny Institute of Natural History, Bradford, PA)

2007-07-01T23:59:59.000Z

104

Isolation of levoglucosan from lignocellulosic pyrolysis oil derived from wood or waste newsprint  

DOE Patents (OSTI)

A method is provided for preparing high purity levoglucosan from lignocellulosic pyrolysis oils derived from wood or waste newsprint. The method includes reducing wood or newsprint to fine particle sizes, treating the particles with a hot mineral acid for a predetermined period of time, and filtering off and drying resulting solid wood or newsprint material; pyrolyzing the dried solid wood or newsprint material at temperatures between about 350 and 375 C to produce pyrolysis oils; treating the oils to liquid-liquid extraction with methyl isobutyl ketone to remove heavy tar materials from the oils, and to provide an aqueous fraction mixture of the oils containing primarily levoglucosan; treating the aqueous fraction mixtures with a basic metal salt in an amount sufficient to elevate pH values to a range of about 12 to about 12.5 and adding an amount of the salt in excess of the amount needed to obtain the pH range to remove colored materials of impurities from the oil and form a slurry, and freeze-drying the resulting slurry to produce a dry solid residue; and extracting the levoglucosan from the residue using ethyl acetate solvent to produce a purified crystalline levoglucosan. 2 figs.

Moens, L.

1995-07-11T23:59:59.000Z

105

Isolation of levoglucosan from lignocellulosic pyrolysis oil derived from wood or waste newsprint  

DOE Patents (OSTI)

A method is provided for preparing high purity levoglucosan from lignocellulosic pyrolysis oils derived from wood or waste newsprint. The method includes reducing wood or newsprint to fine particle sizes, treating the particles with a hot mineral acid for a predetermined period of time, and filtering off and drying resulting solid wood or newsprint material; pyrolyzing the dried solid wood or newsprint material at temperatures between about 350.degree. and 375.degree. C. to produce pyrolysis oils; treating the oils to liquid-liquid extraction with methyl isobutyl ketone to remove heavy tar materials from the oils, and to provide an aqueous fraction mixture of the oils containing primarily levoglucosan; treating the aqueous fraction mixtures with a basic metal salt in an amount sufficient to elevate pH values to a range of about 12 to about 12.5 and adding an amount of the salt in excess of the amount needed to obtain the pH range to remove colored materials of impurities from the oil and form a slurry, and freeze-drying the resulting slurry to produce a dry solid residue; and extracting the levoglucosan from the residue using ethyl acetate solvent to produce a purified crystalline levoglucosan.

Moens, Luc (Lakewood, CO)

1995-01-01T23:59:59.000Z

106

Sources of heavy metal contamination in Swedish wood waste used for combustion  

SciTech Connect

In this paper, wood waste (RWW) recovered for heat production in Sweden was studied. Previous research has concluded that RWW contains elevated amounts of heavy metals, causing environmental problems during waste management. This study extends previous work on RWW by analysing which pollution sources cause this contamination. Using existing data on the metal contents in various materials, and the amounts of these materials in RWW, the share of the elevated amounts of metals in RWW that these materials explain was quantified. Six different materials occurring in RWW were studied and the results show that they explain from 70% to 100% of the amounts of arsenic, chromium, lead, copper and zinc in RWW. The most important materials contributing to contamination of RWW are surface-treated wood, industrial preservative-treated wood, plastic and galvanised fastening systems. These findings enable the development and evaluation of strategies aiming to decrease pollution and resource loss from handling RWW. It is argued that source separation and measures taken further downstream from the generation site, such as treatment, need to be combined to substantially decrease the amount of heavy metals in RWW.

Krook, J. [Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden)]. E-mail: joakr@ikp.liu.se; Martensson, A. [Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden); Eklund, M. [Department of Mechanical Engineering, Linkoeping University, SE-581 83 Linkoeping (Sweden)

2006-07-01T23:59:59.000Z

107

Solid Waste Rules (New Hampshire) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

by the solid waste rules for authorizing construction, operation, and closure of solid waste management facilities. The act includes rules for waste-to-energy operations...

108

International Best Practices for Pre-Processing and Co-Processing Municipal Solid Waste and Sewage Sludge in the Cement Industry  

E-Print Network (OSTI)

n.d. Co-Processing of Waste and Energy Efficiency By CementAnnual North American Waste-to-Energy Conference NAWTEC17,2009. Stantec, 2011. Waste to Energy: a Technical Review of

Hasanbeigi, Ali

2013-01-01T23:59:59.000Z

109

Co-combustion of textile residues with cardboard and waste wood in a packed bed  

SciTech Connect

The combustible fraction of the municipal waste is mostly bio-derived. Energy recovery of the wastes that cannot be economically recycled is a key part of sustainable energy policy and waste management. Textile residues have high energy content. When burned alone in a packed bed system, however, their combustion efficiency is low due to the irregular propagation of the ignition front and the low burning rates. In order to achieve more efficient combustion of textile residues, a series of co-combustion tests were carried out for various mixture compositions and air flow rates in a packed bed combustor. The combustion performance of these materials was evaluated by using quantitative measures such as ignition rate, burning rate and equivalence ratio. Co-combustion of textile residues with cardboard for a textile fraction of up to 30% achieved satisfactorily high burning rate and low unburned carbon content in the bottom ash. The mixture was more resistant to convective cooling by air, which significantly expanded the range of air flow rate for combustion at high burning rates. In co-combustion with a material that has a very low ignition front speed such as waste wood, the propagation of the ignition front was governed by textile residues. Therefore, the co-combustion of textile residues can be better performed with a material having similar ignition front speeds, in which the two materials simultaneously burn at the ignition front. (author)

Ryu, Changkook; Phan, Anh N; Sharifi, Vida N; Swithenbank, Jim [Sheffield University Waste Incineration Centre (SUWIC), Department of Chemical and Process Engineering, The University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

2007-11-15T23:59:59.000Z

110

THE ROLE OF WASTE-TO-ENERGY IN SOLID WASTE MANAGEMENT Introduction  

E-Print Network (OSTI)

Quadrennial Congress, Vienna, Austria, May 1 996. The ISWA 25th Anniversary Congress, Yokohama, Japan

Columbia University

111

future science group 133ISSN 1758-300410.4155/CMT.12.11 2012 Future Science Ltd Municipal solid waste (MSW) is a ubiquitous byprod-  

E-Print Network (OSTI)

- monly known as waste-to-energy (WTE). This method reduces the land requirement for waste disposal of waste-to-energy in reducing GHG emissions Munish K Chandel1 , Gabriel Kwok2 , Robert B Jackson*1 or electricity (waste-to-energy [WTE]) could reduce net GHG emissions in the USA compared with combusting methane

Jackson, Robert B.

112

Waste as a Renewable Source of Energy  

E-Print Network (OSTI)

Waste as a Renewable Source of Energy Dr. Karsten Millrath Columbia University / Waste-To-Energy Waste Management · Status of Renewable · Current and Future Practices · The Waste-To-Energy Research management practices renewable resources> Millrath 10 #12;MSW as Renewable Energy Source · Broader

Columbia University

113

Dover Textiles - A Case History on Retrofitting Factories with a Boiler System Fueled on Coal, Wood and Waste  

E-Print Network (OSTI)

The shortage of affordable gas and oil boiler fuels and the recent Iran/Iraq war underscores the urgent need for the American industrial system to convert to domestically controlled fuels and particularly coal, wood, and waste. More talk than action has been present. However, Dover Textiles, Shelby, North Carolina, is a major textile concern which has aggressively addressed the high cost and vulnerability of oil, as well as the increasing cost of natural gas, for their boiler system by purchasing a coal, wood, and waste fired boiler system to serve two plants. This case history will document payback periods of less than three years; return on investments of 20% plus; benefits of North Carolina and federal investment tax credits; EPA considerations, which in this case required no additional capital investment; fuel supply; material handling; ash removal; and other design considerations.

Pincelli, R. D.

1981-01-01T23:59:59.000Z

114

Potential use of wood and agriculture wastes as steam generator fuel for thermal enhanced oil recovery. Final report  

DOE Green Energy (OSTI)

Enhanced oil recovery by steam injection methods produces over 200,000 barrels per day of crude oil in California. A sizeable portion of the produced crude, up to 40% for some projects, may be burned to generate steam for injection into the reservoir. The purpose of this study is to evaluate the potential to use wood and agriculture wastes to replace crude oil as steam generator fuel. The Bakersfield area of California's San Joaquin Valley is the focus for this paper. Production from thermal EOR methods centers around Bakersfield and agriculture and wood wastes are available from the San Joaquin Valley and the nearby Sierra Nevada mountains. This paper documents the production of waste materials by county, estimated energy value of each material, and estimated transportation cost for each material. Both agriculture and wood wastes were found to be available in sizeable quantities and could become attractive steam generation fuels. However, some qualifications need to be made on the use of these materials. Transportation costs will probably limit the range of shipping these materials to perhaps 50 to 100 miles. Availability is subject to competition from existing and developing uses of these materials, such as energy sources in their immediate production area. Existing steam generators probably cannot be retrofitted to burn these materials. Fluidized bed combustion, or low Btu gasification, may be a good technology for utilization. FBC or FBG could accept a variety of waste materials. This will be important because the amount of any single waste may not be large enough to support the energy requirements of a good size thermal f a good size thermal EOR operation.

Kosstrin, H.M.; McDonald, R.K.

1979-01-01T23:59:59.000Z

115

Zero Waste Program 2011 Recycling Benefits  

E-Print Network (OSTI)

of the following homes per month: 10,343 286 tons of plastic 95 tons of aluminum 0 KW-Hrs of Electricity from Waste-to-Energy: This provides enough energy to heat and cool at a Waste-to-Energy (WTE) the following homes per month: 10Rutgers Zero Waste Program 2011 Recycling Benefits Through WM's Recycling Program, our company

Delgado, Mauricio

116

Environmental assessment of the atlas bio-energy waste wood fluidized bed gasification power plant. Final report  

DOE Green Energy (OSTI)

The Atlas Bio-Energy Corporation is proposing to develop and operate a 3 MW power plant in Brooklyn, New York that will produce electricity by gasification of waste wood and combustion of the produced low-Btu gas in a conventional package steam boiler coupled to a steam-electric generator. The objectives of this project were to assist Atlas in addressing the environmental permit requirements for the proposed power plant and to evaluate the environmental and economic impacts of the project compared to more conventional small power plants. The project`s goal was to help promote the commercialization of biomass gasification as an environmentally acceptable and economically attractive alternative to conventional wood combustion. The specific components of this research included: (1) Development of a permitting strategy plan; (2) Characterization of New York City waste wood; (3) Characterization of fluidized bed gasifier/boiler emissions; (4) Performance of an environmental impact analysis; (5) Preparation of an economic evaluation; and (6) Discussion of operational and maintenance concerns. The project is being performed in two phases. Phase I, which is the subject of this report, involves the environmental permitting and environmental/economic assessment of the project. Pending NYSERDA participation, Phase II will include development and implementation of a demonstration program to evaluate the environmental and economic impacts of the full-scale gasification project.

Holzman, M.I.

1995-08-01T23:59:59.000Z

117

Exergy analysis of the Chartherm process for energy valorization and material recuperation of chromated copper arsenate (CCA) treated wood waste  

Science Conference Proceedings (OSTI)

The Chartherm process (Thermya, Bordeaux, France) is a thermochemical conversion process to treat chromated copper arsenate (CCA) impregnated wood waste. The process aims at maximum energy valorization and material recuperation by combining the principles of low-temperature slow pyrolysis and distillation in a smart way. The main objective of the exergy analysis presented in this paper is to find the critical points in the Chartherm process where it is necessary to apply some measures in order to reduce exergy consumption and to make energy use more economic and efficient. It is found that the process efficiency can be increased with 2.3-4.2% by using the heat lost by the reactor, implementing a combined heat and power (CHP) system, or recuperating the waste heat from the exhaust gases to preheat the product gas. Furthermore, a comparison between the exergetic performances of a 'chartherisation' reactor and an idealized gasification reactor shows that both reactors destroy about the same amount of exergy (i.e. 3500 kW kg{sub wood}{sup -1}) during thermochemical conversion of CCA-treated wood. However, the Chartherm process possesses additional capabilities with respect to arsenic and tar treatment, as well as the extra benefit of recuperating materials.

Bosmans, A., E-mail: anouk.bosmans@mech.kuleuven.be [Department of Mechanical Engineering, Katholieke Universiteit Leuven, Celestijnenlaan 300A, 3001 Heverlee (Belgium); Auweele, M. Vanden; Govaerts, J.; Helsen, L. [Department of Mechanical Engineering, Katholieke Universiteit Leuven, Celestijnenlaan 300A, 3001 Heverlee (Belgium)

2011-04-15T23:59:59.000Z

118

TOTAL WATER REUSE AT A WASTE-TO-ENERGY DAVID CHILD  

E-Print Network (OSTI)

. It has been used as makeup to cooling towers and for use in condensers for many years. In some, the cooling tower blowdown, miscellaneous washwaters and makeup from the Elizabethtown WWTP facility

Columbia University

119

12th North American Waste to Energy Conference May 17-19. 2004. Savannah. Georgia USA  

E-Print Network (OSTI)

of recyclable ferrous and nonferrous metals and about 165,000 MWHR per year of power. Significant Historical by EBIIDA associated with installation time and forced outage time. A comparison was made between costs reduced. The analysis shows that costs chargeable to the superheater will be reduced by 46% per year

Columbia University

120

Microsoft Word - Oneida Waste to Energy Project DOE Final EA 1862  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

ONEIDA SEVEN GENERATIONS ONEIDA SEVEN GENERATIONS CORPORATION: ENERGY RECOVERY PROJECT, GREEN BAY, WISCONSIN U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Golden Field Office NOVEMBER 2011 DOE/EA-1862 FINAL ENVIRONMENTAL ASSESSMENT FOR THE ONEIDA SEVEN GENERATIONS CORPORATION: ENERGY RECOVERY PROJECT, GREEN BAY, WISCONSIN U.S. Department of Energy Office of Energy Efficiency and Renewable Energy Golden Field Office NOVEMBER 2011 DOE/EA-1862 DOE/EA-1862 iii November 2011 COVER SHEET RESPONSIBLE AGENCY: U.S. Department of Energy TITLE: Environmental Assessment for Oneida Seven Generations Corporation: Energy Recovery Project, Green Bay, Wisconsin (DOE/EA-1862) CONTACT: For more information on this Environmental Assessment (EA), please contact:

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Proceedings of NAWTEC16 16th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

advanced oxygen enrichment technology. However, there are also over 100 thermal treatment plants based: Stoker (CFB) (Figure and they are c e feed, to mak of Chinese MS he total ther is estimated 50 facilities Institute o f the Chinese y Prof. Yunhan of Zhejiang U eported to be s/day are unde cy of scaveng results

Columbia University

122

DOD-DOE Workshop Summary on Converting Waste to Energy Using Fuel Cells Table of Contents  

E-Print Network (OSTI)

streams into usable fuel for energy conversion devices (such as combustion engines, boilers, gas turbines of the Union: President Obama's Plan to Win the Future," The White House, January 25, 2011, http://www.whitehouse.gov/the-press-office/2011/01/25/fact-sheet-state-union-president-obamas-plan- win-future; Office of the Press Secretary

123

10th North American Waste to Energy Conference NAWTEC10-1004  

E-Print Network (OSTI)

superheater 1, passes through a spray attemperator and enters platen superheater 2 located in the right hand attemperator and into superheater 3 located in the 5th pass between superheater 4 and economizer 3. Steam from

Columbia University

124

13th North American Waste to Energy Conference May 23-25, 2005, Orlando, Florida USA  

E-Print Network (OSTI)

identify this parameter, was again the acoustic valve leak detection survey. In checking the attemperator it to operate at a slightly higher back pressure resulting in additional power loss Attemperator or de. The superheater attemperator block valves were found leaking. By repairing these during subsequent outages

Columbia University

125

11th North American Waste to Energy Conference Copyright Q 2003 by ASME  

E-Print Network (OSTI)

through a secondary section also in the 2"4 pass. An attemperator for final steam temperature contro valves. A steam attemperator section was installed between the high-temperature primary and the secondary

Columbia University

126

13th North American Waste to Energy Conference May 23-25, 2005, Orlando, Florida USA  

E-Print Network (OSTI)

. Water is not used for boiler cleaning. The superheater sections utilize dual attemperators a small amount of superheater attemperation spray. The achievement of rated steam temperatures has

Columbia University

127

Proceedings of the 18th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

will be combined with petroleum coke as fuel in fluidized bed combustion facilities to generate steam and electric and St. Thomas, have a projected cost of $440 million and will convert an estimated 146,000 tons per year MW of electric power to St. Croix, and will help to provide long-term cost stability for electric

Columbia University

128

11th North American Waste to Energy Conference Copyright 2003 by ASME  

E-Print Network (OSTI)

flue gas in an intensive contact with Ca(OH)z, open hearth furnace coke, water and recirculated, in the TURBOSORP® FGC process open-hearth oven coke (HOC) is injected in addition to the sorbent containing calcium during the operation of the pilot plant. As already mentioned above open-hearth oven coke is added

Columbia University

129

13th North American Waste to Energy Conference May 23-25, 2005, Orlando, Florida USA  

E-Print Network (OSTI)

-permeability sand packs [41]. The layer-partitioning technique may produce a significant error when applied to tight in the experiment. The absolute permeability of the sand packs used in the experiments was between 17.8 and 262

Columbia University

130

11th North American Waste to Energy Conference Copyright 2003 by ASME  

E-Print Network (OSTI)

of synthesis gas from gasification of animal manure was estimated to be around 4.2 MJ/m3 (113 Btu/ft3 ................................................................................................5 Gasification Experiments ............................................................................................................8 Manure gasification experiment conducted on July, 9 2008

Columbia University

131

10th North American Waste to Energy Conference NAWTEC10-1012  

E-Print Network (OSTI)

, and production cost estimates for gasification-based thermochemical conversion of switchgrass into FischerOctober 2005 Gasification-Based Fuels and Electricity Production from Biomass, without......................................................................... 9 3.1.1 Biomass Gasification

Columbia University

132

13th North American Waste to Energy Conference May 23-25, 2005, Orlando, Florida USA  

E-Print Network (OSTI)

, renewables, and coal gasification-based energy supply technologies, can enable China to meet economic), and (3) coal gasification technolo- gies co-producing electricity and clean liquid and gaseous energy-induced oil price shocks. · Estimate the relative costs of achieving target levels of reductions in air

Columbia University

133

11th North American Waste to Energy Conference Copyright 2003 by ASME  

E-Print Network (OSTI)

equipment, as well as validate Phase I cost estimates for pelletization. Further gasification tests-3154 GASIFICATION I COGENERATION USING MSW RESIDUALS AND BIOMASS ABSTRACT Jim Schubert, P. Eng. General Supervisor estimated at 50,000 tonnes per year. Objective and Approach The City of Edmonton, in partnership

Columbia University

134

12th North American Waste to Energy Conference May 17-19, 2004, Savannah, Georgia USA  

E-Print Network (OSTI)

receiver hitch and mounting frame. 100.00$ #12008 Great Plains Air drill distributor tower 10.00$ #12009 cogs 2.00$ #12017 Sewer line rueter 5.00$ #12018 Craftsman spray gun and canister 5.00$ #12019 4 water

Columbia University

135

PEER-REVIEW Air PollutionControl for Waste to Energy Plants -  

E-Print Network (OSTI)

included two plate and frame coolers along with two pumps located next to the existing cooling tower (C to increased air supply demand by the spray dryer absorbers (SDAs) and fabric filters (FFs). A system of air-cell cooling tower (located 160 feet east of the dry coolers) with chlorides and biocides attaching

Columbia University

136

HIGH CAPACITY WASTE-TO-ENERGY CONVERSION AT THE KIEL DISTRICT HEATING STATION  

E-Print Network (OSTI)

as from its participation in a joint · 9 venture with Nordwestdeutsche Kraftwerke A.G. . The latter

Columbia University

137

10th North American Waste to Energy Conference NAWTEC10-1005  

E-Print Network (OSTI)

) to control the particulate emissions. Dry sorbent (trona) was injected just upstream of the economizer controlled by dry sorbent injection (trona) at the economizer inlet. Performance of the dry sorbent injection

Columbia University

138

New Mercury Control Technology for the Ft. Dix Waste-to-Energy Plant Sid Nelson Jr.  

E-Print Network (OSTI)

temperature. Mercury chloride (HgCI2) tends to be found in incinerator flue gases and this species may be well mercury measurement with no interference from acidic gases, such as S02. Low-Temperature Sorbents After of the oxidized mercury species, such as mercury chloride. Then, the large surface area in the baghouse would

Columbia University

139

13th North American Waste to Energy Conference May 23-25, 2005, Orlando, Florida USA  

E-Print Network (OSTI)

was mercury adsorption onto calcium sulfate (CaSO4), a byproduct of the flue gas desulfurization (FGD) wet., Powers K.W., and Pitoniak E.R. (2004) Method for Purifying Flue Gases from Combustion Sources. PatentCoupling of Advanced Oxidation and Adsorption Processes onto Silica-Titania Composites for Low

Columbia University

140

9th Annual North American Waste to Energy Conference NEW FGD DEVELOPMENTS IN EUROPE  

E-Print Network (OSTI)

in the exhaust flue gases from the MSW incinerators consist of nitric oxide (NO) and nitrogen dioxide (N02) which/fabric filter system to reduce nitrogen oxide, mercury and dioxin levels to meet the most recent Ontario combustion. The flue gases that exit the secondary chamber enter the heat recovery boilers where high

Columbia University

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

9th Annual North American Waste to Energy Conference MERCURY CEMs: TECHNOLOGY UPDATE  

E-Print Network (OSTI)

in Baltimore, MD, Scrubber Dry Adsorber (SDA), SNCR and Mercury APC systems were added to the existing technology (Baghouse). Most large MWCs have to install a Mercury Control system to meet the Federal Emission Guidelines. New Jersey and Florida have developed more stringent mercury standards than the federal limits

Columbia University

142

ANALYSIS OF THERMAL PLASMA ASSISTED WASTE-TO ENERGY Caroline Ducharme, Nickolas Themelis  

E-Print Network (OSTI)

............................................................. 7 Gasification Direct Solar Gasification...................................................................... 11 Miscellaneous Gasification Processes.................................................... 11 Biomass

Columbia University

143

Technical and economic analysis of Plasma-assisted Waste-to-Energy processes  

E-Print Network (OSTI)

on a process of a hydrothermal gasification to produce hydrogen from wet biomass, such as sewage treatment energy efficiency. Thus, scientists in the KIT experimental center of the world's largest microwave is provided by powerful gyrotron tubes, a kind of microwave oven. This 140 gigahertz gyrotron developed at KIT

Columbia University

144

10th North American Waste to Energy Conference NAWTEC10-1028  

E-Print Network (OSTI)

diamond. We describe a new ultrananocrystalline diamond (UNCD) film technology based on a microwave plasma 542 3.2. Ar-rich CH4/Ar microwave plasma growth process for ultrananocrystalline diamond (UNCD) films-rich CH4/Ar microwave plasma growth process for ultrananocrystalline diamond (UNCD) films In the process

Columbia University

145

11th North American Waste to Energy Conference Copyright 2003 by ASME  

E-Print Network (OSTI)

added for NOx control. Some WTE facilities as a result of their specific combustion technology andlor/dscm 0.49 mg/dscm 1.6 mg/dscm Mercury 0.080 mg/dscm or 0.080 mg/dscm or .080 mg/dscm or 85% reduction 85% reduction 85% reduction ACID GASES Sulfur Dioxide (S02) 29 ppmv or 75% 31 ppmv or 75% 77 ppmv or 50

Columbia University

146

REDUCING OXIDES OF NITROGEN EMISSIONS FROM WASTE-TO-ENERGY FACILITIES WITH  

E-Print Network (OSTI)

compromising combustion ef ficiency. Further research to determine the potential for NOx reduction via to a lower level by applying combustion control for the reduction of NOx, while still maintaining acceptable, resulting in a 30% reduction of NOx' The techniques developed from this test program are used today

Columbia University

147

PERFORMANCE OF NOx CONTROL TECHNOLOGIES ON THREE CALIFORNIA WASTE-TO-ENERGY  

E-Print Network (OSTI)

catalytic reduction (SNCR) technology. There is a sub stantial volume of literature available discussing NOx in the first three undergrate zones on the SERRF units. Preliminary indications were that some NOx reduction) to quantify the effect of FGR's contribution to NOx reduction during simultaneous FGRIThermal DeNOx use; (b

Columbia University

148

9th Annual North American Waste to Energy Conference USING FLAME QUENCHING TO REDUCE  

E-Print Network (OSTI)

; · Reductions in NOx by lowering flame temperature; and , · The generation of new revenues by utilizing for NOx reduction include load reduction, excess air reduction, stage firing, chemical injection (urea; · Reductions in combustion velocities and tube erosion rate; · Reductions in thermal NOx by loweringflame

Columbia University

149

Waste-to-Energy and Fuel Cell T h l i O i  

E-Print Network (OSTI)

. Compressor Station PSA Cleanup System #12;Landfill Gas Contaminants vs Fuel Cell Specs. Contaminant Landfill: High levels of contamination Time varying output of gas quantity and quality Innovation for Our Energy-scale Food Processing · LandfillsLandfills · Dairy and Pig Farms (~200 W/Cow) · Pulp and Paper Mills

150

Proceedings of NAWTEC 17 Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

, there are about 20 large scale fluidized bed incinerators of co-firing MSW with coal that have been commercially co-firing MSW with coal in China. J. Hazard. Mater. A135, 47­51. Zhang, H.J., Ni, Y.W., Chen, J

Columbia University

151

14th North American Waste to Energy Conference May 1-3,2006, Tampa, Florida USA  

E-Print Network (OSTI)

,000 references > Operation and maintenance > Modernisation and upgrades > Co-firing of biomass > Emission

Columbia University

152

15th North American Waste to Energy Conference May 21-23, 2007, Miami, Florida USA  

E-Print Network (OSTI)

tidal stream, others nuclear, with most supporting co-firing of biomass with coal on the sites be given to a long term future for co-firing of biomass in the few remaining large coal-fired power

Columbia University

153

14th North American Waste to Energy Conference May 1-3, 2006, Tampa, Florida USA  

E-Print Network (OSTI)

.000 +---.-..--.......;..------........---...-.....oio;;;;_............,...............+__I......._I1 3.500 +------------..-..._-.......,,-I

Columbia University

154

10th North American Waste to Energy Conference NAWTEC10-1007  

E-Print Network (OSTI)

: GLOSSARY kBg kilobecquerels kwH kilowatt hours LED light emitting diode LIE Long Island Expressway LINAC trichloroethylene TCLP toxicity characteristic leaching procedure TLD thermoluminescent dosimeter TSCA Toxic

Columbia University

155

Reducing Waste and Harvesting Energy This Halloween | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

process work? Similar to composting, one method of converting waste to energy is called anaerobic digestion. This is a natural process where microorganisms are used to break down...

156

WASTE TO WATTS Waste is a Resource!  

E-Print Network (OSTI)

WASTE TO WATTS Waste is a Resource! energy forum Case Studies from Estonia, Switzerland, Germany BREFs and their BATs Next Generation of Waste Fired Power Plants: Getting the most out of your trash Bossart,· ABB Waste-to-Energy Plants Edmund Fleck,· ESWET Marcel van Berlo,· Afval Energie Bedrijf From

Columbia University

157

Energy Basics: Wood and Pellet Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

EERE: Energy Basics Wood and Pellet Heating Wood-burning and pellet fuel appliances use biomass or waste resources to heat homes or buildings. Types of Wood- and Pellet-Burning...

158

Energy Basics: Wood and Pellet Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Heating & Cooling Systems Water Heating Wood and Pellet Heating Wood-burning and pellet fuel appliances use biomass or waste resources to heat homes or buildings. Types of Wood-...

159

Evaluation of the Natick enzymatic hydrolysis process for use in the production of ethanol from municipal solid waste or from wood. Final report  

DOE Green Energy (OSTI)

Economic evaluation of a conceptual, large-scale, commercial ethanol production facility using the enzymatic hydrolysis technology are presented. Designs and cost estimates for the mechanical processing and the ethanol fermentation and recovery are included. Production of ethanol from both wood and solid wastes is covered. (MHR)

Jones, J. L.; Fong, W. S.; Chatterjee, A. K.

1979-10-01T23:59:59.000Z

160

WOOD FLOORING 1. INTRODUCTION TO WARM AND WOOD FLOORING  

E-Print Network (OSTI)

This chapter describes the methodology used in EPAs Waste Reduction Model (WARM) to estimate streamlined life-cycle greenhouse gas (GHG) emission factors for wood flooring beginning at the waste generation reference point. 1 The WARM GHG emission factors are used to compare the net emissions associated with wood flooring in the following three waste management alternatives: source reduction, combustion, and landfilling.

unknown authors

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Using the sun and waste wood to heat a central Ohio home. Final technical report  

DOE Green Energy (OSTI)

The description of a house in Ohio built on a south facing slope with two levels above ground on the north, east, and west sides and three levels exposed to the southern winter Sun is presented. The floor plan, a general history of the project, the operation of the system, the backup heat source (wood), the collection of data, and the procedure for determining actual heat loss are described. Additionally, the calculation of the solar contribution percentage and the amount of mass to be included in the greenhouse and problems with an indirect gain wall are discussed. The location of the wood stove in the system is noted. The east wall temperature data are given. Soil temperature, air infiltration, thermal comfort, and energy usage are discussed. (MCW).

Not Available

1981-01-01T23:59:59.000Z

162

Online elemental analysis of process gases with ICP-OES: A case study on waste wood combustion  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Simultaneous measurements of 23 elements in process gases of a waste wood combustor. Black-Right-Pointing-Pointer Mobile ICP spectrometer allows measurements of high quality at industrial plants. Black-Right-Pointing-Pointer Continuous online measurements with high temporal resolution. Black-Right-Pointing-Pointer Linear correlations among element concentrations in the raw flue gas were detected. Black-Right-Pointing-Pointer Novel sampling and calibration methods for ICP-OES analysis of process gases. - Abstract: A mobile sampling and measurement system for the analysis of gaseous and liquid samples in the field was developed. An inductively coupled plasma optical emission spectrometer (ICP-OES), which is built into a van, was used as detector. The analytical system was calibrated with liquid and/or gaseous standards. It was shown that identical mass flows of either gaseous or liquid standards resulted in identical ICP-OES signal intensities. In a field measurement campaign trace and minor elements in the raw flue gas of a waste wood combustor were monitored. Sampling was performed with a highly transport efficient liquid quench system, which allowed to observe temporal variations in the elemental process gas composition. After a change in feedstock an immediate change of the element concentrations in the flue gas was detected. A comparison of the average element concentrations during the combustion of the two feedstocks showed a high reproducibility for matrix elements that are expected to be present in similar concentrations. On the other hand elements that showed strong differences in their concentration in the feedstock were also represented by a higher concentration in the flue gas. Following the temporal variations of different elements revealed strong correlations between a number of elements, such as chlorine with sodium, potassium and zinc, as well as arsenic with lead, and calcium with strontium.

Wellinger, Marco, E-mail: marco.wellinger@gmail.com [General Energy Research Department, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Ecole Polytechnique Federale de Lausanne (EPFL), School of Architecture, Civil and Environmental Engineering (ENAC-IIE), CH-1015 Lausanne (Switzerland); Wochele, Joerg; Biollaz, Serge M.A. [General Energy Research Department, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Ludwig, Christian, E-mail: christian.ludwig@psi.ch [General Energy Research Department, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Ecole Polytechnique Federale de Lausanne (EPFL), School of Architecture, Civil and Environmental Engineering (ENAC-IIE), CH-1015 Lausanne (Switzerland)

2012-10-15T23:59:59.000Z

163

WASTE SEPARATION-DOES IT INFLUENCE MUNICIPAL WASTE COMBUSTOR EMISSIONS?  

E-Print Network (OSTI)

WASTE SEPARATION- DOES IT INFLUENCE MUNICIPAL WASTE COMBUSTOR EMISSIONS? A. John Chandler A a commendable job in proving that trace emissions from a modem waste to energy plant have little to do with the trace compounds in individual components of municipal solid waste. Ogden, the leader in designing

Columbia University

164

WOOD PRODUCTS 1. INTRODUCTION TO WARM AND WOOD PRODUCTS  

E-Print Network (OSTI)

This chapter describes the methodology used in EPAs Waste Reduction Model (WARM) to estimate streamlined life-cycle greenhouse gas (GHG) emission factors for wood products beginning at the point of waste generation. The WARM GHG emission factors are used to compare the net emissions associated with wood products in the following four materials management alternatives: source

unknown authors

2012-01-01T23:59:59.000Z

165

Capacity-to-Act in India's Solid Waste Management and Waste-to-  

E-Print Network (OSTI)

1 Capacity-to-Act in India's Solid Waste Management and Waste-to- Energy Industries Perinaz Bhada and disposal of garbage, or municipal solid waste, compounded by increasing consumption levels. Another serious of converting waste into different forms of energy. The process of using waste as a fuel source and converting

Columbia University

166

Waste incineration and the community -  

E-Print Network (OSTI)

Waste incineration and the community - The Amsterdam experience The successful community relations strategy followed by the operator of Amsterdam's waste-to- energy plant has convinced the public and other stakeholders of the benefits of incineration for treating the city's waste Thomas McCarthy Article by Thomas Mc

Columbia University

167

9th Annual North American Waste to Energy Conference WATER RECLAMATION PRACTICES AT THE PINELLAS COUNTY (FL)  

E-Print Network (OSTI)

.7 million gallons per day (MGD) of makeup water for the cooling tower and up to 200 thousand gallons per day in the cooling towers. Reclaimed water for boiler makeup will require membrane treatment followed by ion exchange cooling is achieved by a circulating water system through a five (5) cell mechanical draft cooling tower

Columbia University

168

15th North American Waste to Energy Conference May May 21-23, 2007, Miami, Florida USA  

E-Print Network (OSTI)

as its standard for about the last 10 years. Even when combined with scheduled maintenance outages that has typically had 4 outages per year involving off-line cleaning, including the 2 annual maintenance for 4-112 months, which was the longest run without an off-line cleaning in over 4 years. Cost

Columbia University

169

THERMAL TREATMENT REVIEW . WTE I THERMAL TREATMENT Since the beginning of this century, global waste-to-energy capacity  

E-Print Network (OSTI)

at the dust source, changed intensity of the atmospheric flow or to changed scavenging parameters. Furthermore supported by funding agencies in Denmark (SNF), Belgium (FNRS-CFB), France (IFRTP and INSU/CNRS), Ger-5 many.: Oxygen isotope and palaeotem- perature records from six Greenland ice-core stations: Camp Century, Dye-3

Columbia University

170

15th North American Waste to Energy Conference May May 21-23, 2007, Miami, Florida USA  

E-Print Network (OSTI)

temperature was reduced by changing the original steam flow path and adding a second attemperator and Primary II. Two attemperators are used. One is placed between Primary II and the Intennediate temperature. Figure 2 depicts the present configuration of the two Copyright © 2007 by ASME #12;attemperators

Columbia University

171

1 Copyright 2010 by ASME Proceedings of the 18th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

. The temperature control principle for live steam is not as conventional by attemperators; it is done by load

Columbia University

172

Copyright 2009 by ASME Proceedings of the 17th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

metals and dioxin/furans from the process gas; and the handling of a relatively large amount of ash costly WTE plants. Some of the factors to be examined are: Feed-stock handling; heat generation rate per thermal efficiency; cost of APC (air pollution control) system because of the need to remove volatile

Columbia University

173

1 Copyright 2009 by ASME Proceedings of the 17th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

Influence of Ceria on the NOx Storage/Reduction Behavior of Lean NOx Trap Catalysts Yaying Jia diesel exhaust conditions, employing NOx storage/reduction cycles. NOx storage efficiency an imbalance in the rates of nitrate decomposition and NOx reduction. Optimal NOx conversion was obtained

Columbia University

174

C o p y r i Proceedings of the 18th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

, they represent all gall types and crucial life history traits that are found in the Fordinae (Wool, 1984 belonging to the genus Baizongiini, are included in the present study (Table 1; Table 1 Life history traits in Koach and Wool, 1977). The life cycle of the Fordinae includes sexual and asexual reproduction

Columbia University

175

Wood as a fuel. (Latest citations from the NTIS Bibliographic database). Published Search  

SciTech Connect

The bibliography contains citations concerning the availability, combustion aspects, economics, and feasibility of using wood as fuel. Topics include wood-fuel power plants, wood waste fuels, district heating systems, wood burning furnaces and appliances, and wood waste generators. (Contains a minimum of 128 citations and includes a subject term index and title list.)

Not Available

1994-05-01T23:59:59.000Z

176

Development of METHANE de-NOX Reburn Process for Wood Waste and Biomass Fired Stoker Boilers - Final Report - METHANE de-NOX Reburn Technology Manual  

Science Conference Proceedings (OSTI)

The overall objective of this project was to demonstrate the effectiveness of the METHANE de-NOX (MdN) Reburn process in the Forest Products Industry (FPI) to provide more efficient use of wood and sludge waste (biosolids) combustion for both energy generation and emissions reduction (specifically from nitrogen oxides (NOx)) and to promote the transfer of the technology to the wide range of wood waste-fired stoker boilers populating the FPI. This document, MdN Reburn Commercial Technology Manual, was prepared to be a resource to promote technology transfer and commercialization activities of MdN in the industry and to assist potential users understand its application and installation requirements. The Manual includes a compilation of MdN commercial design data from four different stoker boiler designs that were baseline tested as part of the development effort. Design information in the Manual include boiler CFD model studies, process design protocols, engineering data sheets and commercial installation drawings. Each design package is unique and implemented in a manner to meet specific mill requirements.

J. Rabovitser; B. Bryan; S. Wohadlo; S. Nester; J. Vaught; M. Tartan (Gas Technology Institute) L. Szymanski; R. Glickert (ESA Environmental Solutions)

2007-12-31T23:59:59.000Z

177

Clean Energy Portfolio Goal | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

forest thinnings, mill residue wood, animal wastes, animal byproducts, aquatic plants and algae; hydropower; fuel cells; hydrogen; energy from waste to energy facilities, including...

178

Clean Energy Portfolio Goal | Open Energy Information  

Open Energy Info (EERE)

thinnings, mill residue wood, animal wastes, animal byproducts, aquatic plants and algae; hydropower; fuel cells; hydrogen; energy from waste to energy facilities, including...

179

Waste in a land of plenty -Solid waste generation and management  

E-Print Network (OSTI)

Waste in a land of plenty - Solid waste generation and management in the US The US generates the highest amount of waste per person in the world and continues to rely on landfilling at the expense of recycling and waste-to- energy, according to the latest in an annual series of national surveys on municipal

Columbia University

180

Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2010;  

U.S. Energy Information Administration (EIA) Indexed Site

Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2010; Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2010; Level: National and Regional Data; Row: Selected NAICS Codes; Column: Energy Sources; Unit: Trillion Btu. Wood Residues and Wood-Related Pulping Liquor Wood Byproducts and NAICS or Biomass Agricultural Harvested Directly from Mill Paper-Related Code(a) Subsector and Industry Black Liquor Total(b) Waste(c) from Trees(d) Processing(e) Refuse(f) Total United States 311 Food 0 44 43 * * 1 311221 Wet Corn Milling 0 1 1 0 0 0 312 Beverage and Tobacco Products 0 1 0 0 1 0 321 Wood Products 0 218 * 13 199 6 321113 Sawmills 0 100 * 5 94 1 3212 Veneer, Plywood, and Engineered Woods 0 95 * 6 87 2 321219 Reconstituted Wood Products 0 52 0 6 46 1 3219 Other Wood Products

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Waste as a Renewable Source of Energy  

E-Print Network (OSTI)

Waste as a Renewable Source of Energy Karsten Millrath and N.J. Themelis Columbia University) Overview · Waste-To-Energy · Municipal Solid Waste Management · Status of Renewable · Current and Future renewable resources> Millrath 9 MSW as Renewable Energy Source · Broader definition of renewable energy

Columbia University

182

Turning waste into energy beats landfilling  

E-Print Network (OSTI)

Turning waste into energy beats landfilling By Christopher Hume The Hamilton Spectator (Nov 16 it in Europe, "waste-to-energy," this is a technology that is needed. Objections to it are based on information lots, perhaps $300 million. But what Miller and others fail to understand is that energy-to-waste

Columbia University

183

Comments of the Integrated Waste Services Association Florida PSC Renewable Portfolio Standard Workshop  

E-Print Network (OSTI)

The following comments are submitted by the Integrated Waste Services Association (IWSA). IWSA is the national trade association representing the nations waste-to-energy industry and municipalities. Waste-to-energy facilities produce clean, renewable energy through the combustion of municipal solid waste in specially designed power plants equipped with the most modern pollution control equipment to clean emissions. Trash volume is reduced by 90 % and the remaining residue is safely reused or disposed in landfills. There are 87 waste-to-energy plants operating in 25 states managing about 13 percent of Americas trash, or about 95,000 tons each day. Waste-toenergy generates about 2,700 megawatts of electricity to meet the power needs of nearly 2.3 million homes while serving the trash disposal needs of more than 36 million people. In Florida, 11 WTE plants process over 18,000 tons per day of municipal solid waste, and 514 megawatts of electricity. Waste to Energy benefits in relation to Greenhouse Gases: In response to recent discussions regarding greenhouse gases at the workshop, IWSA would like to point out that a number of studies have shown that waste-to-energy is better than carbon neutral. Use of waste-to-energy avoids emissions from fossil fuel-fired electric generation, fugitive methane emissions from decomposing trash in landfills and avoidance of emissions from production of new

unknown authors

2007-01-01T23:59:59.000Z

184

A survey of state clean energy fund support for biomass  

E-Print Network (OSTI)

as wood, agricultural, or food wastes, energy crops, biogas,v) landfill gas; (vi) waste-to-energy which is a componentChop Energy Costs and Recycle Wood Waste. http://

Fitzgerald, Garrett; Bolinger, Mark; Wiser, Ryan

2004-01-01T23:59:59.000Z

185

Annual Transuranic Waste Inventory Report - 2013  

NLE Websites -- All DOE Office Websites (Extended Search)

contain both combustible and noncombustible waste items. Combustible waste may include wood, plastics, paper, and rags. Noncombustible waste items may include metals, glass,...

186

OpenEI - Wood and Derived Fuels  

Open Energy Info (EERE)

UK Energy Statistics: UK Energy Statistics: Renewables and Waste, Commodity Balances (2010) http://en.openei.org/datasets/node/82 Annual commodity balances (supply, consumption) for renewables and waste in the UK from 1998 to 2009. Published as part of the Digest of UK energy statistics (DUKES), by the UK Department of Energy & Climate Change (DECC). Waste includes: wood waste, farm waste, sewage gas, landfill gas, waste and tyres. Renewables includes: wood, plant-based biomass, geothermal and active solar heat, hydro, wind, wave and tidal, and liquid biofuels.

License
Type of

187

Wood compost process engineering, properties and its impact on extreme soil characteristics.  

E-Print Network (OSTI)

??The landfilling of biodegradable waste is proven to contribute to environmental degradation. Much wood and lumber is discharged as waste from the cleared fields. These (more)

Nada, Wael Mohamed Abdel-Rahman

2011-01-01T23:59:59.000Z

188

Jordan Woods  

NLE Websites -- All DOE Office Websites (Extended Search)

Jordan Woods Windows and Envelope Materials Group Lawrence Berkeley National Laboratory 1 Cyclotron Road MS 90R2000 Berkeley CA 94720 Office Location: 90-2052C (510) 486-4931...

189

Drew Wood  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood Indoor Air Quality Research Collaborative drew@iaqrc.org This speaker was a visiting speaker who delivered a talk or talks on the date(s) shown at the links below. This...

190

Hot Issue and Burning Options in Waste Management: A Social Cost Benefit Analysis of Waste-to-Energy in the UK.  

E-Print Network (OSTI)

in the form of the Renewable Obligation Order, replacing the Non-Fossil Fuel Obligation (NFFO) as the instrument for supporting the development of renewable energy. Suppliers must purchase annually increasing percentages of their electricity from accredited... to exclude WtE (and large hydro) from ROCs is justified by the Government on the grounds that the technology is already capable of competing with electricity from fossil fuels without additional support (DTI, 2000). By distinguishing between renewable...

Jamasb, Tooraj; Kiamil, H; Nepal, R

191

Municipal Solid Waste Resources and Technologies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies October 7, 2013 - 9:28am Addthis Black and white photo of a bulldozer pushing a large mound of trash in a landfill. The National Renewable Energy Laboratory's high-solids digester converts wastes to biogas and compost for energy production. This page provides a brief overview of municipal solid waste energy resources and technologies supplemented by specific information to apply waste to energy within the Federal sector. Overview Municipal solid waste, also known as waste to energy, generates electricity by burning solid waste as fuel. This generates renewable electricity while also incinerating landfill and other municipal waste products such as trash, yard clippings and debris, furniture, food scraps, and other

192

Municipal Solid Waste Resources and Technologies | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies Municipal Solid Waste Resources and Technologies October 7, 2013 - 9:28am Addthis Black and white photo of a bulldozer pushing a large mound of trash in a landfill. The National Renewable Energy Laboratory's high-solids digester converts wastes to biogas and compost for energy production. This page provides a brief overview of municipal solid waste energy resources and technologies supplemented by specific information to apply waste to energy within the Federal sector. Overview Municipal solid waste, also known as waste to energy, generates electricity by burning solid waste as fuel. This generates renewable electricity while also incinerating landfill and other municipal waste products such as trash, yard clippings and debris, furniture, food scraps, and other

193

Wood and Derived Fuels | OpenEI  

Open Energy Info (EERE)

1 1 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142288361 Varnish cache server Wood and Derived Fuels Dataset Summary Description Annual commodity balances (supply, consumption) for renewables and waste in the UK from 1998 to 2009. Published as part of the Digest of UK energy statistics (DUKES), by the UK Department of Energy & Climate Change (DECC). Waste includes: wood waste, farm waste, sewage gas, landfill gas, waste and tyres. Renewables includes: wood, plant-based biomass, geothermal and active solar heat, hydro, wind, wave and tidal, and liquid biofuels. Source UK Department of Energy and Climate Change (DECC) Date Released July 29th, 2010 (4 years ago)

194

From wood to waste and waste to wood.  

E-Print Network (OSTI)

??In this thesis the flow of elements from the forest to the pulp mill and the possibility to recycle nutrients in solid pulp-mill residues back (more)

Rothpfeffer, Caroline

2007-01-01T23:59:59.000Z

195

STOICHIOMETRY OF WOOD LIQUEFACTION  

E-Print Network (OSTI)

co 2 By decomposition to (2) - 0 in H cf 0 in wood TABLE VForced Balance - Wood to Char Output - 55 lbs char lbsuc -61 STOICHIOMETRY OF WOOD LIQUEFACTION Hubert G. Davis

Davis, Hubert G.

2013-01-01T23:59:59.000Z

196

Wood Burning Combined Cycle Power Plant  

E-Print Network (OSTI)

A combined cycle power plant utilizing wood waste products as a fuel has been designed. This plant will yield a 50% efficiency improvement compared to conventional wood-fueled steam power plants. The power plant features an externally-fired gas turbine combined cycle system that obtains its heat input from a high temperature, high pressure ceramic air heater burning wood waste products as a fuel. This paper presents the results of the design study including the cycle evaluation and a description of the major components of the power plant. The cycle configuration is based on maximum fuel efficiency with minimum capital equipment risk. The cycle discussion includes design point performance of the power plant. The design represents a significant step forward in wood-fueled power plants.

Culley, J. W.; Bourgeois, H. S.

1984-01-01T23:59:59.000Z

197

Alaska Wood Biomass Energy Project Final Report  

SciTech Connect

The purpose of the Craig Wood Fired Boiler Project is to use waste wood from local sawmilling operations to provide heat to local public buildings, in an effort to reduce the cost of operating those buildings, and put to productive use a byproduct from the wood milling process that otherwise presents an expense to local mills. The scope of the project included the acquisition of a wood boiler and the delivery systems to feed wood fuel to it, the construction of a building to house the boiler and delivery systems, and connection of the boiler facility to three buildings that will benefit from heat generated by the boiler: the Craig Aquatic Center, the Craig Elementary School, and the Craig Middle School buildings.

Jonathan Bolling

2009-03-02T23:59:59.000Z

198

Cow2Joules: Distributed Conversion of Organic Waste to Energy Resources Background to the project THEY are undertaking at ESF DLJohnson, Feb. 2009  

E-Print Network (OSTI)

large-scale biogas plants have been constructed to extract energy from residential, agricultural for simple, stable, small-scale operations. 1 http://www.iea-biogas.net/ 2 http://www.epa://www.morrisville.edu/alternativeenergy/methanedigester.aspx 5 Arthur Wellinger (unpublished) http://homepage2.nifty.com/biogas/cnt/refdoc/whrefdoc/d14prdgn

Chatterjee, Avik P.

199

Proceedings of the 18th Annual North American Waste-to-Energy Conference May 11-13, 2010, Orlando, Florida, USA  

E-Print Network (OSTI)

shell (biomass) cellulosa type of reaction flash pyrolysis pyrolysis flash pyrolysis slow pyrolysis. Scott, J. Piskorz, D. Radlein; Liquid Products from the Continuous Flash Pyrolysis of Biomass, Ind. Eng; The Continous Flash Pyrolysis of Biomass, The Canadian Journal of Chemical Engineering, 1984, 62, 404-412 #12

Columbia University

200

Copyright 2010 Babcock Power Inc. All Rights Reserved Proceedings of the 18th Annual North American Waste-to-Energy Conference  

E-Print Network (OSTI)

to develop effective Hg0 capture or oxidation technologies. In coal combustion flue gases, Hg0 is oxidized mercury in the gas phase upon introduction of KI, indicating that the oxidation product HgI2 was captured and hydrogen bromide gas16 to flue gas was demonstrated to enhance Hg0 oxidation, but the extent of enhancement

Columbia University

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Proceedings of the 17th Annual North American Waste-to-Energy Conference May 18-20, 2009, Chantilly, Virginia, USA  

E-Print Network (OSTI)

by an estimated 30%. However, the capital, operating and maintenance costs of the shredding equipment should realized through the pre-processing of MSW by means of modern shredding equipment are evaluated both take place at the WTS, thus increasing density and decreasing transportation costs

Columbia University

202

Proceedings of the 17th Annual North American Waste-to-Energy Conference May 18-20, 2009, Chantilly, Virginia, USA  

E-Print Network (OSTI)

with 100ml/min of purge gas at 825o C). Two main steps of thermal degradation have been observed. The first the optimal operating regime for MSW gasification, a series of tests covering a range of temperatures (280) was landfilled and more than 31 million tons (12.4% of total) of materials were combusted with energy recovery[1

Columbia University

203

Trends and Market Effects of Wood Energy Policies  

E-Print Network (OSTI)

Trends and Market Effects of Wood Energy Policies Bengt Hillring SLU SWEDEN http is the main international energy source · Climate change ­ Energy production ­ CO2 · European Union different the plans to increase #12;#12;Energy Sector Waste Sector Recovered Wood Sawdust Logging Residues Forest

204

BEE 4760. Solid Waste Engineering Spring Semester 2010  

E-Print Network (OSTI)

chemistry, energy balance, environmental impacts & controls Sanitary Landfills: planning & operation, gas characterization and reduction; collection and transport systems; waste-to-energy combustion; sanitary landfills) management. 2. An ability to plan and design MSW disposal facilities ­ landfills and incineration. 3

Walter, M.Todd

205

BEE 476. Solid Waste Engineering Spring Semester 2007  

E-Print Network (OSTI)

chemistry, energy balance, environmental impacts & controls Sanitary Landfills: planning & operation, gas characterization and reduction; collection and transport systems; waste-to-energy combustion; sanitary landfills) management. 2. An ability to plan and design MSW disposal facilities ­ landfills and incineration. 3

Walter, M.Todd

206

BEE 476. Solid Waste Engineering Spring Semester 2008  

E-Print Network (OSTI)

chemistry, energy balance, environmental impacts & controls Sanitary Landfills: planning & operation, gas characterization and reduction; collection and transport systems; waste-to-energy combustion; sanitary landfills) management. 2. An ability to plan and design MSW disposal facilities ­ landfills and incineration. 3

Walter, M.Todd

207

The Texarkana Wood Preserving Company Superfund site  

E-Print Network (OSTI)

is a former wood-treating site located in Texas that treated various wood products with chemical preservatives. These activities left behind contaminated soil and sludge, that led to contaminated groundwater. In 1990 Environmental Protection Agency (EPA) selected incineration as the means to clean up contaminated soil at this site. In 1994 Congressman Jim Chapman (D-Texas) asked the Office of Technology Assessment (OTA) to review alternative technologies that might be used instead of incineration at the Texarkana site. A second, separate study to assess the safety of incineration was also requested by Representative Chapman. This report reviews technologies available for hazardous waste cleanup at wood-treating sites throughout the United States. OTA found that there are many Superfund wood-treatment sites located in this country that are very similar in terms of the contaminants

Roger C. Herdman; Frank Avvisato

1995-01-01T23:59:59.000Z

208

Wood Use Across Time  

E-Print Network (OSTI)

?Forest products history and use ?Forest resource- the big picture ?Consumption- the big picture ?Trends forest products industry ? pulp & paper ? solid woodBack in Time ?1492 ? Columbus sailed the ocean blue! ? wood use- fuelwood American Indians ?1634: Jean Nicolet

Scott Bowe; United States Wood Use

2005-01-01T23:59:59.000Z

209

Energie-Cits 2001 BIOMASS -WOOD  

E-Print Network (OSTI)

Energie-Cités 2001 BIOMASS - WOOD Gasification / Cogeneration ARMAGH United Kingdom Gasification is transferring the combustible matters in organic waste or biomass into gas and pure char by burning the fuel via it allows biomass in small-scaled engines and co-generation units ­ which with conventional technologies

210

Residential Wood Residential wood combustion (RWC) is  

E-Print Network (OSTI)

Residential Wood Combustion Residential wood combustion (RWC) is increasing in Europe because PM2.5. Furthermore, other combustion- related sources of OA in Europe may need to be reassessed. Will it affect global OA emission estimates? Combustion of biofuels is globally one of the major OA sources

211

Wood and Pellet Heating Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood and Pellet Heating Basics Wood and Pellet Heating Basics Wood and Pellet Heating Basics August 16, 2013 - 3:02pm Addthis Wood-burning and pellet fuel appliances use biomass or waste resources to heat homes or buildings. Types of Wood- and Pellet-Burning Appliances The following is a brief overview of the different types of wood and pellet fuel appliances available. High-Efficiency Fireplaces and Fireplace Inserts Designed more for show, traditional open masonry fireplaces should not be considered heating devices. Traditional fireplaces draw in as much as 300 cubic feet per minute of heated room air for combustion, then send it straight up the chimney. Fireplaces also produce significant air pollution. Although some fireplace designs seek to address these issues with dedicated air supplies, glass doors, and heat recovery systems, fireplaces are still

212

STEO October 2012 - wood  

U.S. Energy Information Administration (EIA) Indexed Site

More U.S. households burning wood this winter to stay warm, More U.S. households burning wood this winter to stay warm, reversing two-decade decline Burning wood as the primary heating source in U.S. households has risen over the last 10 years, reversing the decline seen in the 1980s and 1990s. About 2.6 million households out of 115 million will rely on wood as the main way to warm their homes this winter. That's up 3 percent from last year, according to the U.S. Energy Information Administration's new winter fuels forecast. The West will have the most households using wood as their primary space heating fuel, followed by the Midwest, South and Northeast regions of the United States. Wood is also the second most common backup fuel, after electricity, that households across the U.S. use as a supplemental heating source. Almost half of all rural households use wood this

213

Waste Management & Research290 Waste Manage Res 2002: 20: 290301  

E-Print Network (OSTI)

Waste Management & Research290 Waste Manage Res 2002: 20: 290­301 Printed in UK ­ all rights reserved Copyright © ISWA 2002 Waste Management & Research ISSN 0734­242X Introduction Chromated copper of sorting technologies for CCA treated wood waste Monika Blassino Helena Solo-Gabriele University of Miami

Florida, University of

214

Wood pellet production  

Science Conference Proceedings (OSTI)

Southern Energy Limited's wood pellet refinery, Bristol, Florida, produces wood pellets for fuel from scrap wood from a nearby sawmill and other hog fuel delivered to the plant from nearby forest lands. The refinery will provide 50,000 tons of pellets per year to the Florida State Hospital at Chattahoochee to fire recently converted boilers in the central power plant. The pellets are densified wood, having a moisture content of about 10% and a heating value of 8000 Btu/lb. They are 0.5 inches in diameter and 2 to 3 inches in length.

Moore, J.W.

1983-08-01T23:59:59.000Z

215

HYDROLYZED WOOD SLURRY FLOW MODELING  

E-Print Network (OSTI)

LBL-10090 UC-61 HYDROLYZED WOOD SLURRY FLOW MODELING JimLBL-10090 HYDROLYZED WOOD SLURRY FLOW MODELING Jim Wrathallconversion of hydrolyzed wood slurry to fuel oil, Based on

Wrathall, Jim

2012-01-01T23:59:59.000Z

216

Integrated Waste Management in Sweden Where incineration is not a dirty word  

E-Print Network (OSTI)

the opportunity to visit a Swedish waste-to-energy plant in Malmö and was amazed at how clean and technologically on their own or through public or private contractors. Needless to say, there is a strong economic incentive, rather than deal with it later. By mixing economic incentives, such as garbage collection fees, with easy

Columbia University

217

Effects of wood fuel use on plant management  

SciTech Connect

During the winter of 1979-80, about 20% of homeowners in the New England region relied on wood fuel as their primary source of heat; an additional 30% used wood heat on a supplementary basis. The demand for wood put a great strain on the New England forests. However, experts in forest management believe that with proper management and utilization, national forest growth could replace as much as four billion gpy of oil by 2023. Implications for the forests of the Upper Great Lakes region of increased use of public and private woodlands for fuel are examined. Conflicts that could arise with the tourist and recreation industry, and with wilderness preservation interests, and discussed. Wood wastes generated by timber harvesting, sawmills, and lumber manufacturing could be collected and used as fuel, thus reducing the amount of raw wood resources needed to fill the increasing demand. (6 photos)

Harris, M.; Buckmann, C.A.

1980-09-01T23:59:59.000Z

218

Pellet stoves wood energy for all  

Science Conference Proceedings (OSTI)

While it`s true that specialized pellet stoves, capable of burning fuels as diverse as reprocessed paper waste and feed corn, are expensive and occasionally clunky, they also represent one of the best hopes for introducing clean burning, reliable renewable energy to those now heating with gas and oil. This article explores the benefits and operation of the stoves including discussions of the following: ecological benefits, combustion, stove venting, ashes, costs, fuels, and the future of wood heat. 1 tab.

NONE

1995-10-01T23:59:59.000Z

219

Wood Heating Fuel Exemption  

Energy.gov (U.S. Department of Energy (DOE))

This statute exempts from the state sales tax all wood or "refuse-derived" fuel used for heating purposes. The law does not make any distinctions about whether the qualified fuels are used for...

220

Gregory H. Woods  

Energy.gov (U.S. Department of Energy (DOE))

Gregory H. Woods was sworn in as the General Counsel of the Department of Energy on April 16, 2012, following the unanimous confirmation of his appointment by the United States Senate. Mr....

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Gregory H. Woods  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

H. Woods H. Woods Department· of Energy Fermi Site Office Post Office Box 2000 Batavia, Illinois 60510 JAN 1 1 2DD Office of the General Counsel GC-1, FORS SUBJECT: FERMI SITE OFFICE (FSO) 2013 ANNUAL NATIONAL ENVIRONMENTAL POLICY ACT (NEPA) PLANNING SUMMARY Section 5(a) (7) of Department Of Energy Order 451.1 B Change 2, NEPA Compliance Program, requires each Secretarial Officer and Head of Field Organization to submit an annual NEPA

222

Finishing Wood Decks  

E-Print Network (OSTI)

Wood decks have become an important part of residential construction in recent years. However, there is considerable confusion regarding how these structures should be protected with finish. This paper summarizes the types, application techniques, and expected service lives of various finishes on both preservative treated and untreated lumber. Recommendations are made on the basis of decades of research on various wood species using a wide variety of finishes.

R. Sam Williams; et al.

1993-01-01T23:59:59.000Z

223

Treated Wood Pole Management  

Science Conference Proceedings (OSTI)

This document characterizes similarities and differences in international wood pole and wood pole preservative management. The research team identified practices for selection, regulation, and disposition of utility poles outside the United States. Most information is based on interviews and website and published literature searches. Additional research will clarify regulatory positions in other countries and generate improved understanding, which will support strategic planning for U.S. utilities. Utili...

2008-10-29T23:59:59.000Z

224

HOW ENVIRONMENTAL RISK FROM LEACH ING OF HEAVY METALS IN ASH RESIDUES FROM COMBUSTION OF MUNIC IPAL SOLID WASTE  

E-Print Network (OSTI)

Laboratories which led to the use of acid tests such as the EP and TCLP tests. [25] 13 #12;CONCLUSIONS and soluble metals in the ash from Waste-to Energy (WTE) facilities has led to a public concern about why has led to the requirement for continuous monitoring of oxygen , carbon monoxide (CO) , and acid gases

Columbia University

225

Creosote-Treated Wood Poles and Crossarms: Toxicity Characteristic Leaching Procedure (TCLP) Results  

Science Conference Proceedings (OSTI)

If creosote-treated wood poles and crossarms are classified as hazardous waste by the EPA's revised toxicity characteristic rule, disposal costs will rise dramatically. However, when the rule is applied to data obtained from this EPRI study, creosote-treated utility wood poles and crossarms receive a nonhazardous classification.

1992-08-06T23:59:59.000Z

226

Pentachlorophenol (PCP)-Treated Wood Poles and Crossarms: Toxicity Characteristic Leaching Procedure (TCLP) Results  

Science Conference Proceedings (OSTI)

If pentachlorophenol (PCP)-treated wood poles and crossarms are classified as hazardous waste by the revised toxicity characteristic (TC) rule, disposal costs will rise dramatically. However, when the ruling is applied to data obtained during this study, PCP-treated utility wood poles and crossarms receive a nonhazardous classification.

1991-01-03T23:59:59.000Z

227

Prototype demonstration of dual sorbent injection for acid gas control on municipal solid waste combustion units  

SciTech Connect

This report gathered and evaluated emissions and operations data associated with furnace injection of dry hydrated lime and duct injection of dry sodium bicarbonate at a commercial, 1500 ton per day, waste-to-energy facility. The information compiled during the project sheds light on these sorbents to affect acid gas emissions from municipal solid waste combustors. The information assesses the capability of these systems to meet the 1990 Clean Air Act and 1991 EPA Emission Guidelines.

None

1994-05-01T23:59:59.000Z

228

Cofiring Wood and Coal to Stoker Boilers in Pittsburgh  

DOE Green Energy (OSTI)

The prime objective of the University of Pittsburgh's overall wood/coal cofiring program is the successful introduction of commercial cofiring of urban wood wastes into the stoker boilers of western Pennsylvania. Central to this objective is the demonstration test at the Pittsburgh Brewing Company. In this test the project team is working to show that two commercially-available clean wood wastes - tub-ground pallet waste and chipped clearance wood - can be included in the fuel fed daily to an industrial stoker boiler. Irrespective of its economic outcome, the technical success of the demonstration at the brewery will allow the local air quality regulation agency to permit a parametric test at the Bellefield Boiler Plant. The objective of this test is to obtain comprehensive data on all key parameters of this operational boiler while firing wood with coal. The data would then be used for thorough generic technical and economic analyses. The technical analysis would be added to the open literature for the general planning and operational guidance for boiler owners and operators. The economic analysis would gage the potential for providing this stoker fuel commercially in an urban setting and for purchasing it regularly for combustion in an urban stoker boiler.

Cobb, J.T., Jr.; Elder, W.W.

1997-07-01T23:59:59.000Z

229

Principle Wood Scientist  

E-Print Network (OSTI)

Wood, bark, and the wax-coated seeds from Chinese tallow tree (Sapium sebiferum (L.) Roxb. syn. Triadica sebifera (L.) Small), an invasive tree species in the southeastern United States, were subjected to extractions and degradative chemical analyses in an effort to better understand the mechanism(s) by which this tree species aggressively competes against native vegetation, and also to facilitate utilization efforts. Analysis of the wood extractives by FTIR spectroscopy showed functionalities analogous to those in hydrolyzable tannins, which appeared to be abundant in the bark; as expected, the seeds had a high wax/oil content (43.1%). Compared to other fast-growing hardwoods, the holocellulose content for the Chinese tallow tree wood was somewhat higher (83.3%). The alpha-cellulose (48.3%) and Klason lignin (20.3%) contents were found to be similar to those for most native North American hardwoods. Results suggest that Chinese tallow tree wood utilization along with commercial wood species should not present any significant processing problems related to the extractives or cell-wall chemistry. Keywords: Cellulose, Chinese tallow tree, extractives, Klason lignin, utilization.

Thomas L. Eberhardt; Usda Forest Service; Xiaobo Li; Chung Y. Hse; Usda Forest Service

2005-01-01T23:59:59.000Z

230

The Pitfalls of Realist Analysis of Global Capitalism: A Critique of Ellen Meiksins Woods Empire of Capitalism: A Critique of Ellen Meiksins Wood's "Empire of Capital"  

E-Print Network (OSTI)

Boulder: Paradigm Press. Wood, Ellen Meiksins 2002, Globalgroups. 13 Indeed, Wood 2003, p. 23. Wood 2003, p. 132.Ibid. Wood 2003, p. 129. Wood 2003, p. 133. Wood 2003, p.

Robinson, William I.

2007-01-01T23:59:59.000Z

231

Precision wood particle feedstocks  

DOE Patents (OSTI)

Wood particles having fibers aligned in a grain, wherein: the wood particles are characterized by a length dimension (L) aligned substantially parallel to the grain, a width dimension (W) normal to L and aligned cross grain, and a height dimension (H) normal to W and L; the L.times.H dimensions define two side surfaces characterized by substantially intact longitudinally arrayed fibers; the W.times.H dimensions define two cross-grain end surfaces characterized individually as aligned either normal to the grain or oblique to the grain; the L.times.W dimensions define two substantially parallel top and bottom surfaces; and, a majority of the W.times.H surfaces in the mixture of wood particles have end checking.

Dooley, James H; Lanning, David N

2013-07-30T23:59:59.000Z

232

Burls and Other Unusual Woods  

NLE Websites -- All DOE Office Websites (Extended Search)

President Roland F. Eisenbeis, Supt. of Conservation BURLS AND OTHER UNUSUAL WOODS Wood worked by the hands of skilled craftsmen puts a wealth of quiet beauty into our daily...

233

Waste wood processing and combustion for energy  

DOE Green Energy (OSTI)

This volume contains the proceedings of the Fifth Annual National Biofuels Conference and Exhibition held October 19--22, 1992 in Newton, Massachusetts. Individual papers have been abstracted and indexed for the database.

Not Available

1992-12-31T23:59:59.000Z

234

The Asian Wood Pellet Markets  

E-Print Network (OSTI)

. 25 p. This study examines the three major wood pellet markets in Asia: China, Japan, and South Korea, South Korea is striving to increase its per- centage of renewable energy, which could benefit the wood pellets industry. We found that China, the largest energy consumer in Asia, has an established wood pellet

235

China: Changing Wood Products Markets  

E-Print Network (OSTI)

#12;China: Changing Wood Products Markets less is probably known about the forestry and wood products market in China than most other U.S. trading partners. In the 1980s China emerged as the world,11,12). However, U.S. wood products exports to China declined nearly 93 percent from 1988 to 1996, from $-I%3

Zhang, Daowei

236

The Wood Duck  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood Duck Wood Duck Nature Bulletin No. 502-A October 13, 1973 Forest Preserve District of Cook County George W. Dunne, President Roland F. Eisenbeis, Supt. of Conservation THE WOOD DUCK Of all the fowl that swim, the Wood Duck is a most unusual bird. They perch in trees like jaybirds, and nest in tree holes like woodpeckers. The hens do not quack like the females of most ducks, and the drakes are dressed in a riot of gaudy colors. Each summer we see dozens of them -- more than any other kind of wild duck -- rear their families of ducklings on and around the streams, ponds, lakes and sloughs of Cook County's forest preserves. Words can scarcely describe the brilliance of the drake's plumage. The head, crest and back glint with iridescent greens, purples and blues. The eyes are red, the throat white, and the bill orange-red. The breast is wine-colored flecked with white, the belly is white, and the sides are buff. The woodie is about midway in size between the mallard and the blue-winged teal. The drakes weigh about a pound and a half. The hen is smaller and plainer, with a gray-brown head and body, a white throat, and a conspicuous white ring around the eye. Her voice is a shrill, squealing "whoo-eek", while the male's is a mere squeak.

237

Wood Inspection by Infrared Thermography  

E-Print Network (OSTI)

Wood is used everywhere and for everything. With times, this material presents many adulterations, witch degrade his physical properties. This work present a study of infrared thermography NDT for wood decay detection. The study is based on the difference of moisture content between sound wood and decay. In the first part, moisture content influence on response signal is determine. The second part define the limits of infrared thermography for wood decay detection. Results show that this method could be used, but with many cautions on depth and size of wood defects.

A. Wyckhuyse; X. Maldague; X. Maldague Corresponding

2002-01-01T23:59:59.000Z

238

Review of the Regional Biomass Energy Program: Technical projects  

Science Conference Proceedings (OSTI)

This article summarizes technical projects of the regional Biomass Energy Program. Projects included are as follows: economic impact studies for renewable energy resources; alternative liquid fuels; Wood pellets fuels forum; residential fuel wood consumption; waste to energy decision-makers guide; fuel assessment for cogeneration facilities; municipal solid waste combustion characteristics.

Lusk, P.

1994-12-31T23:59:59.000Z

239

Short rotation Wood Crops Program  

DOE Green Energy (OSTI)

This report synthesizes the technical progress of research projects in the Short Rotation Woody Crops Program for the year ending September 30, 1989. The primary goal of this research program, sponsored by the US Department of Energy's Biofuels and Municipal Waste Technology Division, is the development of a viable technology for producing renewable feedstocks for conversion to biofuels. One of the more significant accomplishments was the documentation that short-rotation woody crops total delivered costs could be $40/Mg or less under optimistic but attainable conditions. By taking advantage of federal subsidies such as those offered under the Conservation Reserve Program, wood energy feedstock costs could be lower. Genetic improvement studies are broadening species performance within geographic regions and under less-than-optimum site conditions. Advances in physiological research are identifying key characteristics of species productivity and response to nutrient applications. Recent developments utilizing biotechnology have achieved success in cell and tissue culture, somaclonal variation, and gene-insertion studies. Productivity gains have been realized with advanced cultural studies of spacing, coppice, and mixed-species trials. 8 figs., 20 tabs.

Wright, L.L.; Ehrenshaft, A.R.

1990-08-01T23:59:59.000Z

240

Inside the guts of wood-eating catfishes: can they digest wood?  

E-Print Network (OSTI)

the cellulolytic system of the wood-boring marine mollusk2008), how diVerent are the wood-eating catWshes from otherendosymbionts and digest wood, or are these wood- eating

German, Donovan P.

2009-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Hazardous Waste: Resource Pack for Trainers and Communicators | Open Energy  

Open Energy Info (EERE)

Hazardous Waste: Resource Pack for Trainers and Communicators Hazardous Waste: Resource Pack for Trainers and Communicators Jump to: navigation, search Tool Summary Name: Hazardous Waste: Resource Pack for Trainers and Communicators Agency/Company /Organization: International Solid Waste Association (ISWA), United Nations Development Programme (UNDP), United Nations Industrial Development Organization (UNIDO) Sector: Energy, Land, Water Focus Area: Renewable Energy, - Waste to Energy Phase: Evaluate Options Topics: Adaptation, Implementation, Low emission development planning, -LEDS Resource Type: Guide/manual, Training materials Website: www.trp-training.info/ Cost: Paid Language: English References: Training Resource Pack[1] "The new TRP+ provides a structured package of notes, technical summaries, visual aids and other training material concerning the (hazardous) waste

243

CHEMISTRY AND STOICHIOMETRY OF WOOD LIQUEFACTION  

E-Print Network (OSTI)

V. , Anderson, Carry, Academic, New York. Pyrolysis of WoodT.J. Elder, E.J. Soltes, Wood and Fiber, 12(4), 1980, "Phenolic Constituents of a Wood Pyrolytic Oil." J.A. Knight,

Davis, H.G.

2012-01-01T23:59:59.000Z

244

Methanol production from eucalyptus wood chips. Attachment VIII. The wood-fueled gasification system, Evergreen Energy Corporation's final engineering report  

DOE Green Energy (OSTI)

Evergreen Energy Corporation provided projected cost and operating data on the Evergreen/Texaco entrained-bed wood gasification system currently under development as an alternative to the state-of-the-art fixed-bed wood gasification system proposed by Davy McKee. Overall capital costs for the total plant remain about the same at approx. $250 million. The Evergreen/Texaco system will provide significant capital cost savings in the gasifiers, gas cleanup, and waste water treatment sections, and eliminate the need for a large off-site wood-fired power boiler. These reductions are offset by higher investments in the feedstock preparation, drying, and feeding section plus the need for a larger air separation plant and compressor to supply oxygen at high pressure to the gasifier.

Fishkind, H.H.

1982-06-01T23:59:59.000Z

245

An overview of the sustainability of solid waste management at military installations  

SciTech Connect

Sustainable municipal solid waste management at military solutions necessitates a combined approach that includes waste reduction, alternative disposal techniques, and increased recycling. Military installations are unique because they often represent large employers in the region in which they are located, thereby making any practices they employ impact overall waste management strategies of the region. Solutions for waste sustainability will be dependent on operational directives and base location, availability of resources such as water and energy, and size of population. Presented in this paper are descriptions of available waste strategies that can be used to support sustainable waste management. Results presented indicate source reduction and recycling to be the most sustainable solutions. However, new waste-to-energy plants and composting have potential to improve on these well proven techniques and allow military installations to achieve sustainable waste management.

Borglin, S.; Shore, J.; Worden, H.; Jain, R.

2009-08-15T23:59:59.000Z

246

GLOBAL WOOD SUPPLY Sten Nilsson  

E-Print Network (OSTI)

· Increasing demand for wood through population and economic growth · More expensive wood · Where should America Expansion potential USA Deficit Canada Deficit #12;RUSSIA Advantages: Raw Materials Source LEAVED ­ EASTERN USA Source: http://www.cas.vanderbilt.edu/bioimages/biohires/ecoregions/h50404bottomland

247

Daniel Wood | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Wood About Us Daniel Wood - Data Integration Specialist Daniel Wood Daniel Wood is the Data Visualization and Cartographic Specialist in the Office of Public Affairs at the Department of Energy. He develops creative and interactive ways of viewing the Energy Department's vast array of data. You can check out some of his work here. Prior to joining the Energy.gov team, Daniel worked at a large PR firm in Washington, D.C, doing web development and technical project management. Daniel is a graduate of Boston University but a true Philadelphian at heart. On his off days you are likely to find him exploring new neighborhoods on his bike or hanging out with the awesome kids over at Little Lights Urban Ministries. Most Recent The History of the Light Bulb November 22

248

Weathering and Protection of Wood  

E-Print Network (OSTI)

Introduction When wood is exposed outdoors, above ground, a complex combination of chemical, mechanical, and light energy factors contribute to what is described as weathering (38). Weathering is not to be confused with decay, which results from decay organisms (fungi) acting in the presence of excess moisture and air for an extended period of time (34). Under conditions suitable for the development of decay, wood can deteriorate rapidly and the result is far different than that observed for natural outdoor weathering, Outdoor Weathering Process In outdoor weathering of smooth wood, original surfaces become rough as grain raises and the wood checks, and the checks grow into large cracks; grain may loosen, boards cup and warp and pull away from fasteners (Figs. 1 and 2), The roughened surface changes color, gathers dirt and mildew, and may become unsightly; the wood loses its surface coherence and becomes friable, splinters, and frag ments come off. All these e

William C. Feist

1983-01-01T23:59:59.000Z

249

Pollution Prevention Procedure and Case Studies for Utility Waste  

Science Conference Proceedings (OSTI)

Utilities are working to eliminate or minimize the production of waste in all of their operations. This report presents a six-step process for pollution prevention and seven case studies demonstrating successful application of the process to eight utility wastes, including oily absorbents, municipal wastes, paint solvents, waste paint, blast grit, wood waste, unused chemicals, and unknown drum contents. The procedures for each waste are applicable to any utility site.

1996-09-17T23:59:59.000Z

250

Wood Handbook Wood as an Engineering Material Centennial EditionCentennial Edition  

E-Print Network (OSTI)

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

United States; Forest Service; Wood Handbook; Wood As An Engineering Material

2010-01-01T23:59:59.000Z

251

Modelling piloted ignition of wood and plastics  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer We model piloted ignition times of wood and plastics. Black-Right-Pointing-Pointer The model is applied on a packed bed. Black-Right-Pointing-Pointer When the air flow is above a critical level, no ignition can take place. - Abstract: To gain insight in the startup of an incinerator, this article deals with piloted ignition. A newly developed model is described to predict the piloted ignition times of wood, PMMA and PVC. The model is based on the lower flammability limit and the adiabatic flame temperature at this limit. The incoming radiative heat flux, sample thickness and moisture content are some of the used variables. Not only the ignition time can be calculated with the model, but also the mass flux and surface temperature at ignition. The ignition times for softwoods and PMMA are mainly under-predicted. For hardwoods and PVC the predicted ignition times agree well with experimental results. Due to a significant scatter in the experimental data the mass flux and surface temperature calculated with the model are hard to validate. The model is applied on the startup of a municipal waste incineration plant. For this process a maximum allowable primary air flow is derived. When the primary air flow is above this maximum air flow, no ignition can be obtained.

Blijderveen, Maarten van [TNO, Schoemakerstraat 97, 2628 VK Delft (Netherlands); University of Twente, Department of Thermal Engineering, Drienerlolaan 5, 7522 NB Enschede (Netherlands); Bramer, Eddy A. [University of Twente, Department of Thermal Engineering, Drienerlolaan 5, 7522 NB Enschede (Netherlands); Brem, Gerrit, E-mail: g.brem@utwente.nl [University of Twente, Department of Thermal Engineering, Drienerlolaan 5, 7522 NB Enschede (Netherlands)

2012-09-15T23:59:59.000Z

252

Wood and energy in connecticut. Staff report  

SciTech Connect

Telephone surveys of Connecticut households conducted in 1979 indicate a transition to wood heating in response to a series of conventional energy price increases and uncertainty in conventional energy supplies. Connecticut households consumed 668,000 cords of wood in the winter of 1978-79. The airtight wood stove has become the most commonly used wood-burning apparatus. Survey data of residential wood cutting, purchasing, and burning were analyzed by household tenure, wood-burning apparatus, and county. Residential use of wood for energy constitutes a new demand on the forest resource, increases local income and employment, displaces fuel oil and electricity, but may compromise household safety.

Bailey, M.R.; Wheeling, P.R.; Lenz, M.I.

1983-03-01T23:59:59.000Z

253

The reduction of packaging waste  

Science Conference Proceedings (OSTI)

Nationwide, packaging waste comprises approximately one third of the waste being sent to our solid waste landfills. These wastes range from product and shipping containers made from plastic, glass, wood, and corrugated cardboard to packaging fillers and wraps made from a variety of plastic materials such as shrink wrap and polystyrene peanuts. The amount of packaging waste generated is becoming an important issue for manufacturers, retailers, and consumers. Elimination of packaging not only conserves precious landfill space, it also reduces consumption of raw materials and energy, all of which result in important economic and environmental benefits. At the US Department of Energy-Richland Field Office's (DOE-RL) Hanford Site as well as other DOE sites the generation of packaging waste has added importance. By reducing the amount of packaging waste, DOE also reduces the costs and liabilities associated with waste handling, treatment, storage, and disposal.

Raney, E.A.; McCollom, M.; Hogan, J.

1993-04-01T23:59:59.000Z

254

The reduction of packaging waste  

Science Conference Proceedings (OSTI)

Nationwide, packaging waste comprises approximately one third of the waste being sent to our solid waste landfills. These wastes range from product and shipping containers made from plastic, glass, wood, and corrugated cardboard to packaging fillers and wraps made from a variety of plastic materials such as shrink wrap and polystyrene peanuts. The amount of packaging waste generated is becoming an important issue for manufacturers, retailers, and consumers. Elimination of packaging not only conserves precious landfill space, it also reduces consumption of raw materials and energy, all of which result in important economic and environmental benefits. At the US Department of Energy-Richland Field Office`s (DOE-RL) Hanford Site as well as other DOE sites the generation of packaging waste has added importance. By reducing the amount of packaging waste, DOE also reduces the costs and liabilities associated with waste handling, treatment, storage, and disposal.

Raney, E.A.; McCollom, M.; Hogan, J.

1993-04-01T23:59:59.000Z

255

Managing Transmission Line Wood Structures  

Science Conference Proceedings (OSTI)

The objective of this project is to reduce capital cost by extending life expectancy of overhead transmission wood structures through inspection and assessment procedures and through aging mitigation techniques and tools.

2005-11-29T23:59:59.000Z

256

Treated Wood Planted Post Study  

Science Conference Proceedings (OSTI)

This Technical Update describes the interim results of a planted post study currently under way at the Austin Cary Memorial Forest (ACMF), operated by The University of Florida, in Gainesville. The purpose of this research is to examine the effectiveness of commercially available prevention methods to reduce preservative migration from treated wood poles, compare the migration of constituents of various wood treatments, and assess the environmental impacts and performance of untreated chestnut.

2009-11-12T23:59:59.000Z

257

Chromoblastomycosis associated with in a carpenter handling exotic woods  

E-Print Network (OSTI)

in a carpenter handling exotic woods Nuno Menezes 1 , Pauloas saprophytes in the soil, wood and vegetation [ 3 ]. Theyare normally made of tropical wood [ 9 ]. The inoculation

2008-01-01T23:59:59.000Z

258

Energy aspects of solid waste management: Proceedings  

Science Conference Proceedings (OSTI)

The Eighteenth Annual Illinois Energy Conference entitled Energy Aspects of Solid Waste Management'' was held in Chicago, Illinois on October 29--30, 1990. The conference program was developed by a planning committee that drew upon Illinois energy and environmental specialists from the major sectors including energy industries, environmental organizations, research universities, utility companies, federal, state and local government agencies, and public interest groups. Within this framework, the committee identified a number of key topic areas surrounding solid waste management in Illinois which were the focus of the conference. These issues included: review of the main components of the solid waste cycle in the Midwest and what the relative impact of waste reduction, recycling, incineration and land disposal might be on Illinois' and the Midwest's solid waste management program. Investigation of special programs in the Midwest dealing with sewage sludge, combustion residuals and medical/infectious wastes. Review of the status of existing landfills in Illinois and the Midwest and an examination of the current plans for siting of new land disposal systems. Review of the status of incinerators and waste-to-energy systems in Illinois and the Midwest, as well as an update on activities to maximize methane production from landfills in the Midwest.

Not Available

1990-01-01T23:59:59.000Z

259

Short rotation wood crops program: Annual progress report for 1986  

DOE Green Energy (OSTI)

This report describes accomplishments in the Short Rotation Woody Crops Program (SRWCP) for the year ending September 30, 1986. The program is sponsored by the US Department of Energy's Biofuels and Municipal Waste Technology Division and consists of research projects at 29 institutions and corporations. The SRWCP is an integrated program of research and development devoted to a single objective: improving the productivity, cost efficiency, and fuel quality of wood energy crops as feedstocks for conversion to liquid and gaseous fuels. SRWCP directives have shifted from species-screening and productivity evaluations to large-scale viability trials of model species selected for their productivity potential and environmental compatibility. Populus was chosen the lead genera of five model species, and initial steps were taken toward organizing a Populus Research Consortium. Production yields from SRWCP research plots and coppice studies are discussed along with new efforts to model growth results and characteristics on a tree and stand basis. Structural and chemical properties of short-rotation intensive culture wood have been evaluated to determine the desirability of species traits and the potential for genetic improvements. Innovative wood energy crop handling techniques are presented as significant cost reduction measures. The conclusion is that new specialized wood energy crops can be feasible with the advances that appear technically possible over the next 10 years. 34 refs., 9 figs., 7 tabs.

Ranney, J.W.; Wright, L.L.; Layton, P.A.; McNabb, W.A.; Wenzel, C.R.; Curtin, D.T.

1987-11-01T23:59:59.000Z

260

Wood and Pellet Heating | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood and Pellet Heating Wood and Pellet Heating Wood and Pellet Heating November 25, 2013 - 2:24pm Addthis A wood stove on a stone hearth. | Photo courtesy of ©iStockphoto/King_Louie A wood stove on a stone hearth. | Photo courtesy of ©iStockphoto/King_Louie What does this mean for me? Wood or pellets may be an economical and environmentally sound heating fuel choice. If you live in an area where you can cut your own wood for heating, your fuel will be local and inexpensive. Today you can choose from a new generation of wood- and pellet-burning appliances that are cleaner burning, more efficient, and powerful enough to heat many average-sized, modern homes. Pellet fuel appliances burn small pellets that measure 3/8 to 1 inch in length. Choosing and Installing Wood- and Pellet-Burning Appliances

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

A Research Needs Assessment for waste plastics recycling: Volume 1, Executive summary. Final report  

SciTech Connect

This first volume provides a summary of the entire project. The study utilized the talents of a large number of participants, including a significant number of peer reviewers from industrial companies, government agencies, and research institutes. in addition, an extensive analysis of relevant literature was carried out. In considering the attractiveness of recycling technologies that are alternatives to waste-to-energy combustion units, a systems approach was utilized. Collection of waste streams containing plastics, sortation, and reclamation of plastics and plastic mixtures, reprocessing or chemical conversion of the reclaimed polymers, and the applicability of the products to specific market segments have been analyzed in the study.

1994-12-01T23:59:59.000Z

262

Wood-Composites Industry Benefits from ALS Research  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood-Composites Industry Benefits from ALS Research Wood-Composites Industry Benefits from ALS Research Print Thursday, 25 October 2012 10:44 paris-wood composites Wood scientist...

263

Categorical Exclusion for Wood Pole  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Pole Wood Pole Replacement at two structures (11/6 & 11/9) located along the Oracle-Tucson 115-kV Transmission Line, in Oro Valley, Pima County, Arizona. RECORD OF CATEGORICAL EXCLUSION DETERMINATION A. Proposed Action: Western plans to replace deteriorated wood poles, cross arms and X-braces at two existing H-frame structures (11/6 & 1119) located along the Oracle Tucson 115-kV Transmission Line in Pima, Arizona (Figure 1). Built in 1943, its aging components are beyond repair and require replacement. These poles performed poorly during structural tests, and we consider them unstable. This replacement project will ensure the safety of Western's workers and the public as well as reliability of the bulk electric system. Western will accomplish the work by clearing vegetation and blading a level pad at

264

Marin County- Wood Stove Replacement Rebate Program  

Energy.gov (U.S. Department of Energy (DOE))

The County of Marin has created a rebate program to encourage homeowners to remove or replace non-EPA certified wood-burning heaters (wood stoves and fireplace inserts) with cleaner burning stoves...

265

Structure-Infesting Wood-Boring Beetles  

E-Print Network (OSTI)

Several kinds of beetles damage stored wood, structural timbers and other wood products. This publication explains how to detect, identify, prevent and control powderpost beetle, old house borer and others.

Jackman, John A.

2006-03-28T23:59:59.000Z

266

Wood Cofiring in a Cyclone Boiler at TVA's Allen Fossil Plant  

Science Conference Proceedings (OSTI)

Tests in a 272-MW cyclone boiler show that cofiring wood waste in the form of sawdust and small chips with coal is possible in a stable and routine operation. This report presents biomass data for five series of tests conducted from 1994 through 1996 and an analysis of the NOx reduction achieved.

1997-12-22T23:59:59.000Z

267

Metals Concentrations in Soils Below Decks Made of CCA-Treated Wood  

E-Print Network (OSTI)

the report titled: New Lines of CCA-Treated Wood Research, In-Service and Disposal Issues Which was finalized 13 Street, Suite D Gainesville, FL 32609 Excerpts from Report #00-12 #12;This page left intentionally.S. Environmental Protection Agency UV Ultra Violet UV/Vis Ultra Violet ­ Visible Light Region WET Waste Extraction

Florida, University of

268

Bioenergy and Wood Fiber in Virginia and Beyond John F. Munsell  

E-Print Network (OSTI)

­ Grayson County and others · Northern Virginia ­ Municipal Waste · Bio-fuels / Ethanol Goals ­ VA Energy energy productiongy p · 9% renewable: 47% biomass: 72% wood-based 17.00% 9.00% 31.00% 2% Wind 45% Hydroelectric 11.00% Petroleum Renewable Energy Nuclear Electric Hydroelectric 5% Geothermal 47% 32.00% Coal

Wynne, Randolph H.

269

Field Guide: Visual Inspection of Wood Structures  

Science Conference Proceedings (OSTI)

The Field Guide: Visual Inspection of Wood Structures is a catalog of photographs illustrating various conditions and factors that commonly affect transmission line wood structures, along with their likely causes, a Maintenance Priority Rating, and suggested actions to be taken by utility personnel. Poles, cross-arms, cross-arm braces, X-braces, brackets, anchor rods, guy wires, and direct imbedded foundations are covered. Other sections include types of wood structures, the anatomy of wood ...

2013-10-28T23:59:59.000Z

270

Table 3.6 Selected Wood and Wood-Related Products in Fuel Consumption, 2002  

U.S. Energy Information Administration (EIA) Indexed Site

6 Selected Wood and Wood-Related Products in Fuel Consumption, 2002;" 6 Selected Wood and Wood-Related Products in Fuel Consumption, 2002;" " Level: National and Regional Data; " " Row: Selected NAICS Codes; Column: Energy Sources;" " Unit: Trillion Btu." ,,"S e l e c t e d","W o o d","a n d","W o o d -","R e l a t e d","P r o d u c t s" ,,,,,"B i o m a s s" ,,,,,,"Wood Residues" ,,,,,,"and","Wood-Related" " "," ","Pulping Liquor"," "," ","Wood","Byproducts","and","RSE",," " "NAICS"," ","or","Biomass","Agricultural","Harvested Directly","from Mill","Paper-Related","Row"

271

Table N5.2. Selected Wood and Wood-Related Products in Fuel Consumption, 1998  

U.S. Energy Information Administration (EIA) Indexed Site

2. Selected Wood and Wood-Related Products in Fuel Consumption, 1998;" 2. Selected Wood and Wood-Related Products in Fuel Consumption, 1998;" " Level: National and Regional Data; " " Row: Selected NAICS Codes; Column: Energy Sources;" " Unit: Trillion Btu." ,,"S e l e c t e d","W o o d","a n d","W o o d -","R e l a t e d","P r o d u c t s" ,,,,,"B i o m a s s" ,,,,,,"Wood Residues" ,,,,,,"and","Wood-Related" " "," ","Pulping Liquor"," "," ","Wood","Byproducts","and","RSE",," " "NAICS"," ","or","Biomass","Agricultural","Harvested Directly","from Mill","Paper-Related","Row"

272

Autonomous Underwater Gliders Wood, Stephen  

E-Print Network (OSTI)

26 Autonomous Underwater Gliders Wood, Stephen Florida Institute of Technology United States underwater vehicles to perform ocean surveys. With these vehicles it is now possible for the scientist substances in the ocean such as chemicals from an underwater vent or toxic algae such as red tide

Wood, Stephen L.

273

Wood-Coal Fired "Small" Boiler Case Study  

E-Print Network (OSTI)

Galaxy Carpet Corporation installed a coal and wood waste fired boiler approximately twelve months ago. Its first year net savings were $195,000.00 Total capital investment was paid off in 1.9 years. 20% investment tax credits were granted by the Federal Government. Galaxy Carpet Corporation has been sufficiently impressed with performance, both economically and technically, to place a follow-up order of $1,500,000.00 for a second solid fuel fired boiler system at its Dalton, Georgia Dye House operation.

Pincelli, R. D.

1980-01-01T23:59:59.000Z

274

James F. Wood | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

James F. Wood James F. Wood About Us James F. Wood - Deputy Assistant Secretary for Clean Coal Photo of James Wood Photo of James Wood James F. Wood is currently Deputy Assistant Secretary for Clean Coal in the Office of Fossil Energy (FE). In this position, he is responsible for the management and direction of the Office's clean coal research and development programs. Chief among these is the Carbon Sequestration program, the Clean Coal Power Initiative, and FE's $3.4 billion portfolio of Recovery Act projects. Wood has over 30 years of experience in the power industry. Most recently, he was president and CEO of Babcock Power Inc. (BPI), one of the major US-based designer/manufacturers of environmental, pressure part, heat exchanger, combustion equipment and after-market

275

Qualifying Wood Stove Deduction | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Qualifying Wood Stove Deduction Qualifying Wood Stove Deduction Qualifying Wood Stove Deduction < Back Eligibility Residential Savings Category Bioenergy Maximum Rebate 500 Program Info Start Date 1/1/1994 State Arizona Program Type Personal Deduction Rebate Amount Total cost, exclusive of taxes, interest and other finance charges Provider Arizona Department of Revenue This incentive allows Arizona taxpayers to deduct the cost of converting an existing wood fireplace to a qualifying wood stove. The cost to purchase and install all necessary equipment is tax deductible, up to a maximum $500 deduction. Qualifying wood stoves must meet the standards of performance for new wood heaters manufactured after July 1990, or sold after July 1992 pursuant to [http://www.epa.gov/oecaerth/resources/policies/monitoring/caa/woodstover...

276

WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 December 5, 2013 - 12:00pm Addthis WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP’s wood waste diversion program. WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP's wood waste diversion program. CARLSBAD, N.M. - EM's Waste Isolation Pilot Plant (WIPP) almost doubled its solid waste reduction rate from 15.5 percent in fiscal year 2012 to 33 percent in fiscal year 2013 through programs that diverted WIPP's wood waste from the municipal landfill by reusing, repurposing or recycling.

277

WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Doubles Solid Waste Reduction Rate in Fiscal Year 2013 Doubles Solid Waste Reduction Rate in Fiscal Year 2013 WIPP Doubles Solid Waste Reduction Rate in Fiscal Year 2013 December 5, 2013 - 12:00pm Addthis WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP’s wood waste diversion program. WIPP environmental and operations personnel gather next to pallets that will be provided to the local community as part of WIPP's wood waste diversion program. CARLSBAD, N.M. - EM's Waste Isolation Pilot Plant (WIPP) almost doubled its solid waste reduction rate from 15.5 percent in fiscal year 2012 to 33 percent in fiscal year 2013 through programs that diverted WIPP's wood waste from the municipal landfill by reusing, repurposing or recycling.

278

Summary of Recommendations: Legislative and Regulatory Actions to Consider for Ensuring the Long-Term Effectiveness of the Nevada Renewable Portfolio Standard  

E-Print Network (OSTI)

to the existing RPS. Include Waste-to-Energy as an Eligibleat the workshop for including waste-to-energy as an eligiblepolicy objectives? Waste-to-energy Imports Recap: Policy

Porter, Kevin; Grace, Robert; Wiser, Ryan

2004-01-01T23:59:59.000Z

279

Investment under Regulatory Uncertainty: U.S. Electricity Generation Investment Since 1996  

E-Print Network (OSTI)

orts were mostly mass-burn waste-to-energy plants, but morelonger develops non-waste-to-energy projects in the U.S. ,its core business is waste-to-energy facilities 58 After

Ishii, Jun; Yan, Jingming

2004-01-01T23:59:59.000Z

280

Public Health Benefits of End-Use Electrical Energy Efficiency in California: An Exploratory Study  

E-Print Network (OSTI)

gas, oil, and waste-to-energy (WTE) fired electricityoil, natural gas, or waste-to-energy, or WTE), the generalthose plants burning waste-to- energy (WTE) fuels, such as

McKone, Thomas E.

2011-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

URBAN WOOD/COAL CO-FIRING IN THE BELLEFIELD BOILERPLANT  

DOE Green Energy (OSTI)

An Environmental Questionnaire for the demonstration at the Bellefield Boiler Plant (BBP) was submitted to the national Energy Technology Laboratory. An R&D variance for the air permit at the BBP was sought from the Allegheny County Health Department (ACHD). R&D variances for the solid waste permits at the J. A. Rutter Company (JARC), and Emery Tree Service (ETS) were sought from the Pennsylvania Department of Environmental Protection (PADEP). Construction wood was acquired from Thompson Properties and Seven D Corporation. Verbal authorizations were received in all cases. Memoranda of understanding were executed by the University of Pittsburgh with BBP, JARC and ETS. Construction wood was collected from Thompson Properties and from Seven D Corporation. Forty tons of pallet and construction wood were ground to produce BioGrind Wood Chips at JARC and delivered to Mon Valley Transportation Company (MVTC). Five tons of construction wood were hammer milled at ETS and half of the product delivered to MVTC. Blends of wood and coal, produced at MVTC by staff of JARC and MVTC, were shipped by rail to BBP. The experimental portion of the project was carried out at BBP in late March and early April 2001. Several preliminary tests were successfully conducted using blends of 20% and 33% wood by volume. Four one-day tests using a blend of 40% wood by volume were then carried out. Problems of feeding and slagging were experienced with the 40% blend. Light-colored fly ash was observed coming from the stack during all four tests. Emissions of SO{sub 2}, NOx and total particulates, measured by Energy Systems Associates, decreased when compared with combusting coal alone. A procedure for calculating material and energy balances on BBP's Boiler No.1 was developed, using the results of an earlier compliance test at the plant. Material and energy balances were then calculated for the four test periods. Boiler efficiency was found to decrease slightly when the fuel was shifted from coal to the 40% blend. Neither commercial production of sized urban waste wood for the energy market in Pittsburgh nor commercial cofiring of wood/coal blends at BBP are anticipated in the near future.

James T. Cobb Jr.; Gene E. Geiger; William W. Elder III; William P. Barry; Jun Wang; Hongming Li

2004-04-08T23:59:59.000Z

282

Managing Transmission Line Wood Structures  

Science Conference Proceedings (OSTI)

Transmission and distribution infrastructures throughout the world are aging. As such, inspection, assessment, and maintenance of existing facilities have become increasingly important topics. This valuable reference provides an in-depth look at all facets of an inspection, assessment, and maintenance program for transmission line wood structures to help utilities develop and refine individual maintenance programs. The report is part of a broader multi-year effort by EPRI to develop a comprehensive handb...

2006-09-28T23:59:59.000Z

283

Distribution Library--Wood Poles  

Science Conference Proceedings (OSTI)

EPRI has sponsored research and published information on a wide variety of topics related to wood poles for overhead lines. Many of these resources, particularly older publications, are difficult for EPRI members to find and use. To help ensure retention of this valuable knowledge base, EPRI sponsored the project reported herein to capture this information and make it accessible in an easy-to-use electronic media (E-Media) repository.

2005-12-22T23:59:59.000Z

284

Wood Poles Population with Testing  

Science Conference Proceedings (OSTI)

EPRI's asset management research focuses on developing a rational basis for selecting repair or replacement options for specific classes of equipment by balancing the risks of equipment failure against the costs of continued maintenance or capital replacement. This Model User Guide is a companion to Guidelines for Intelligent Asset Replacement: Volume 4Wood Poles (Expanded Edition), EPRI, Palo Alto, CA: 2006. 1012500, the fourth report on guidelines for asset replacement, which discusses methods for maki...

2006-12-18T23:59:59.000Z

285

Commercial Demonstration of Wood Recovery, Recycling, and Value Adding Technologies  

DOE Green Energy (OSTI)

This commercial demonstration project demonstrated the technical feasibility of converting low-value, underutilized and waste stream solid wood fiber material into higher valued products. With a growing need to increase product/production yield and reduce waste in most sawmills, few recovery operations and practically no data existed to support the viability of recovery operations. Prior to our efforts, most all in the forest products industry believed that recovery was difficult, extremely labor intensive, not cost effective, and that recovered products had low value and were difficult to sell. This project provided an opportunity for many within the industry to see through demonstration that converting waste stream material into higher valued products does in fact offer a solution. Our work, supported by the U.S. Department of Energy, throughout the project aimed to demonstrate a reasonable approach to reducing the millions of recoverable solid wood fiber tons that are annually treated as and converted into low value chips, mulch and fuel. Consequently sawmills continue to suffer from reduced availability of forest resources, higher raw material costs, growing waste disposal problems, increased global competition, and more pressure to operate in an Environmentally Friendly manner. It is our belief (based upon the experience of this project) that the successful mainstreaming of the recovery concept would assist in alleviating this burden as well as provide for a realistically achievable economic benefit to those who would seriously pursue the concept and tap into the rapidly growing ''GREEN'' building marketplace. Ultimately, with participation and aggressive pursuit of the recovery concept, the public would benefit in that: (1) Landfill/disposal waste volume could be reduced adding greater life to existing municipal landfill sites thereby minimizing the need to prematurely license and open added facilities. Also, there would be a cost avoidance benefit associated to what would have been the added municipal (community) management costs involved with maintaining closed landfills. (2) With greater quantities of recovered material being returned to and integrated into manufacturing and the marketplace, reduced demand upon virgin wood sources could help lead the way to promoting improved relations and environmental balance between producers and consumers further expanding the value of our natural resource without adding environmental burden.

Auburn Machinery, Inc.

2004-07-15T23:59:59.000Z

286

Generating Steam by Waste Incineration  

E-Print Network (OSTI)

Combustible waste is a significant source of steam at the new John Deere Tractor Works assembly plant in Waterloo, Iowa. The incinerators, each rated to consume two tons of solid waste per hour, are expected to provide up to 100 percent of the full production process steam requirements. The waste incineration system consists of a wood dunnage shredder, two Skid-Steer Loaders for incinerator charging, two incinerators, and a wet ash conveyor. The equipment is housed in a building with floor space to accommodate loads of combustible waste delivered for incineration. Incombustible material is segregated at the source. A review of operational experience and the results of a study on actual steam production costs will be presented with the intent that others will be able to use the information to advance the state of the art of high volume controlled air waste incineration.

Williams, D. R.; Darrow, L. A.

1981-01-01T23:59:59.000Z

287

EIA Energy Kids - Wood - Energy Information Administration  

U.S. Energy Information Administration (EIA)

1860: Wood was the primary fuel for heating and cooking in homes and businesses, and was used for steam in industries, trains, and boats.

288

The Bending of Wood With Steam.  

E-Print Network (OSTI)

??Based on experimentation with the steam bending of wood to curved shapes, this thesis describes my involvement with three basic aspects of the process. First (more)

Cottey Jr., James H.

2008-01-01T23:59:59.000Z

289

Successful biomass (wood pellets ) implementation in  

E-Print Network (OSTI)

Successful biomass (wood pellets ) implementation in Estonia Biomass Utilisation of Local in Estonia in 1995 - 2002 Regional Energy Centres in Estonia http://www.managenergy.net/conference/biomass

290

Life Cycle Assessment of Wood Pellet.  

E-Print Network (OSTI)

??The primary purpose of this project is to assess the environmental impacts associated with the wood pellet production. The study has extended to the entire (more)

Chen, Siyu

2009-01-01T23:59:59.000Z

291

Methanol production from eucalyptus wood chips  

DOE Green Energy (OSTI)

The technical feasibility of producing methanol from wood is demonstrated and sufficient cost data is provided to allow an assessment of the economic viability.

Fishkind, H.H.

1982-06-01T23:59:59.000Z

292

Wood, Wisconsin: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Wood, Wisconsin: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 43.568752, -90.330887 Loading map... "minzoom":false,"mappingservice":"googlem...

293

Emerging Technologies in Wood Energy Wood can already be used to produce heat and  

E-Print Network (OSTI)

for extension of wood pellet production is lack of appropriate technology in Slovakia. Several typesOverview 1 Development of Wood Chips and Pellets market in Slovakia Jozef Viglasky, SK systems. · Co-combustion of wood residues in existing coal fired power systems. #12;Overview 3

294

Mathematical simulation of temperature profiles within microwave heated wood made for wood-based nanocomposites  

Science Conference Proceedings (OSTI)

High intensive microwave pretreatment is a new method to modify wood for the fabrication of wood-based nanocomposites. Based on the physical law on heat transfer, a mathematical model to describe the temperature profiles within wood heated by high intensive ...

Xianjun Li, Yongfeng Luo, Hongbin Chen, Xia He, Jianxiong Lv, Yiqiang Wu

2013-01-01T23:59:59.000Z

295

Management of offshore wastes in the United States.  

SciTech Connect

During the process of finding and producing oil and gas in the offshore environment operators generate a variety of liquid and solid wastes. Some of these wastes are directly related to exploration and production activities (e.g., drilling wastes, produced water, treatment workover, and completion fluids) while other types of wastes are associated with human occupation of the offshore platforms (e.g., sanitary and domestic wastes, trash). Still other types of wastes can be considered generic industrial wastes (e.g., scrap metal and wood, wastes paints and chemicals, sand blasting residues). Finally, the offshore platforms themselves can be considered waste materials when their useful life span has been reached. Generally, offshore wastes are managed in one of three ways--onsite discharge, injection, or transportation to shore. This paper describes the regulatory requirements imposed by the government and the approaches used by offshore operators to manage and dispose of wastes in the US.

Veil, J. A.

1998-10-22T23:59:59.000Z

296

Textile Drying Via Wood Gasification  

E-Print Network (OSTI)

This project was carried out to investigate the possibility of using wood gas as a direct replacement for natural gas in textile drying. The Georgia Tech updraft gasifier was used for the experimental program. During preliminary tests, the 1 million Btu/hr pilot plant produced clean burning gas which appeared viable for drying textiles. The gasifier was coupled to a modified textile drying oven and a series of tests were carried out to assess product degradation of white, colored, and chemically treated fabrics.

McGowan, T. F.; Jape, A. D.

1983-01-01T23:59:59.000Z

297

Modeling and Rendering Physically-Based Wood Combustion  

Science Conference Proceedings (OSTI)

This paper describes extensions to existing methods for rendering of the effects of combustion on a wood object, adding considerations for wood grain and moisture content.

Riensche, Roderick M.; Lewis, Robert R.

2009-08-01T23:59:59.000Z

298

Compound and Elemental Analysis At Little Valley Area (Wood,...  

Open Energy Info (EERE)

Area (Wood, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Compound and Elemental Analysis At Little Valley Area (Wood, 2002) Exploration...

299

URBAN WOOD/COAL CO-FIRING IN THE BELLEFIELD BOILERPLANT  

DOE Green Energy (OSTI)

During the third quarter, important preparatory work was continued so that the experimental activities can begin early in the fourth quarter. Authorization was awaited in response to the letter that was submitted to the Allegheny County Health Department (ACHD) seeking an R&D variance for the air permit at the Bellefield Boiler Plant (BBP). Verbal authorizations were received from the Pennsylvania Department of Environmental Protection (PADEP) for R&D variances for solid waste permits at the J. A. Rutter Company (JARC), and Emery Tree Service (ETS). Construction wood was acquired from Thompson Properties and Seven D Corporation. Forty tons of pallet and construction wood were ground to produce BioGrind Wood Chips at JARC and delivered to Mon Valley Transportation Company (MVTC). Five tons of construction wood were milled at ETS and half of the product delivered to MVTC. Discussions were held with BBP and Energy Systems Associates (ESA) about the test program. Material and energy balances on Boiler No.1 and a plan for data collection were prepared. Presentations describing the University of Pittsburgh Wood/Coal Co-Firing Program were provided to the Pittsburgh Chapter of the Pennsylvania Society of Professional Engineers, and the Upgraded Coal Interest Group and the Biomass Interest Group (BIG) of the Electric Power Research Institute (EPRI). An article describing the program appeared in the Pittsburgh Post-Gazette. An application was submitted for authorization for a Pennsylvania Switchgrass Energy and Conservation Program.

James T. Cobb, Jr.; Gene E. Geiger; William W. Elder III; William P. Barry; Jun Wang; Hongming Li

2001-08-21T23:59:59.000Z

300

Management Practices for Used Treated Wood  

Science Conference Proceedings (OSTI)

Pentachlorophenol, creosote, and other chemicals are used to preserve poles, crossarms, and railroad ties for the electric, telecommunications, and railroad industries. Each year, millions of pieces of treated wood are retired. This report provides information on current and potential options for management of used treated wood.

1995-08-02T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Treatment of Wood Preserving Wastewater  

E-Print Network (OSTI)

The wastewater produced by the wood preserving industry presents a difficult problem to treat economically. A review of the literature indicates the size of the industry has limited the pursuit of an orderly and economic solution. Atmospheric evaporation was one possible means of treatment which had not been studied to any great degree. Two bench scale evaporation units were employed to determine the fundamental relationships affecting wastewater quality during such treatment. In batch evaporation tests, it was repeatedly demonstrated that a constant rate of total organic carbon and chemical oxygen demand removal occurred as the wastewater was evaporated. A procedure for designing atmospheric evaporation ponds was developed and applied to a hypothetical wood preserving plant. From this example design estimates of equivalent hydrocarbon concentrations in the air downwind of the pond are made. Various other design considerations such as the input data, modifications to the design procedure, solids accumulation, and miscellaneous design aspects are discussed. A treatment scheme incorporating atmospheric evaporation ponds after chemical coagulation and settling is proposed.

Reynolds, T. D.; Shack, P. A.

1976-10-01T23:59:59.000Z

302

Wood3 Resources | Open Energy Information  

Open Energy Info (EERE)

Wood3 Resources Wood3 Resources Jump to: navigation, search Name Wood3 Resources Place Houston, Texas Zip 77056-2409 Product Wood3 Resources is an energy project development firm run by former Federal Energy Regulatory Commission Chairman Pat Wood. Coordinates 29.76045°, -95.369784° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":29.76045,"lon":-95.369784,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

303

Wood Energy Production Credit | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Energy Production Credit Wood Energy Production Credit Wood Energy Production Credit < Back Eligibility Commercial Industrial Savings Category Bioenergy Maximum Rebate Credit may be claimed for a period of five years Program Info Start Date 12/30/1998 (most recent revision) State Missouri Program Type Corporate Tax Credit Rebate Amount $5 per ton of processed materials Provider Missouri Department of Natural Resources Note: No new credits are being issued, effective July 1, 2013. This entry is for informational purposes only. The Wood Energy Tax Credit, as effective January 1, 1997, allows individuals or businesses processing Missouri forestry industry residues into fuels an income tax credit of $5.00 per ton of processed material (e.g., wood pellets). A multiplier of 4 applies to charcoal, based on the

304

UK Energy Statistics: Renewables and Waste, Commodity Balances (2010) |  

Open Energy Info (EERE)

403 403 Varnish cache server Browse Upload data GDR 429 Throttled (bot load) Error 429 Throttled (bot load) Throttled (bot load) Guru Meditation: XID: 2142288403 Varnish cache server UK Energy Statistics: Renewables and Waste, Commodity Balances (2010) Dataset Summary Description Annual commodity balances (supply, consumption) for renewables and waste in the UK from 1998 to 2009. Published as part of the Digest of UK energy statistics (DUKES), by the UK Department of Energy & Climate Change (DECC). Waste includes: wood waste, farm waste, sewage gas, landfill gas, waste and tyres. Renewables includes: wood, plant-based biomass, geothermal and active solar heat, hydro, wind, wave and tidal, and liquid biofuels. These data were used to produce Tables 7.1 to 7.3 in the Digest of United Kingdom Energy Statistics 2010 (available: http://decc.gov.uk/assets/decc/Statistics/publications/dukes/348-dukes-2...).

305

Mutiny on the Bounty or Bountiful Mutants? Diversity and Composition of Wood-Decaying Macrofungi on Hibiscus Tiliaceus Wood in French Polynesia  

E-Print Network (OSTI)

B. G. Jonsson. 1995. Wood-inhabiting fungi and substratumand S. C. Watkinson. 1995. Wood decomposition, higher fungi,combative interaction between wood-decaying basidiomycetes.

Wheaton, Felicia

2006-01-01T23:59:59.000Z

306

Waste2Tricity | Open Energy Information  

Open Energy Info (EERE)

Tricity Tricity Jump to: navigation, search Name Waste2Tricity Place London, United Kingdom Zip EC1V 9EE Sector Hydro, Hydrogen Product W2T is seeking to developer a waste to energy plant combining plasma gasification and hydrogen fuel cells to achieve highly efficient conversion of municipal solid waste to electricity. Coordinates 51.506325°, -0.127144° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":51.506325,"lon":-0.127144,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

307

Converting sensitive waste into cleaner energy  

DOE Green Energy (OSTI)

The destruction of sensitive unclassified information (SUI) has always been expensive due to the need for special controls to ensure its protection from disclosure to unauthorized persons. The sensitive documents were shredded, buried at the landfill, or sent to a recycling company. The Department of Energy (DOE) Idaho National Engineering and Environmental Laboratory (INEEL), operated by Lockheed Martin Idaho Technologies Company (LMITCO), has created an innovative method to dispose of its sensitive unclassified paper waste which has security, economic, and environmental benefits. A new cubing facility at the INEEL converts office and industrial waste into compact cubes which are then combined with coal and burned as a source of heat and process steam to run the Idaho Chemical Processing Plant (ICPP) facility. The process-engineered fuel, consisting of 25% cubes and 75% coal, bums cleaner than coal with lower emissions of sulfur dioxide and nitrogen oxides. The alternative fuel also reduces fuel costs, eliminates paying a recycling company, reduces the expense of landfill disposal, increases the life of the landfill, and provides energy to operate a large facility. The Operations Security (OPSEC) team capitalized on this waste to energy technology by recommending that the large quantities of sensitive information (documents) generated at the INEEL be disposed of in this manner. In addition to the economic and environmental benefits, this disposal method minimizes the vulnerabilities of SUI from disclosure to unauthorized personnel. The {open_quotes}cuber{close_quotes} technology has potential application in government and industry for protection of SUI.

Schriner, D.; Skinner, R.

1997-10-01T23:59:59.000Z

308

Solvolytic liquefaction of wood under mild conditions  

DOE Green Energy (OSTI)

Conversion of wood to liquid products requires cleavage of bonds which crosslink the wood structure. This study examines a low-severity wood solubilization process utilizing a solvent medium consisting of a small amount of sulfuric acid and a potentially wood-derivable alcohol. In one half hour of reaction time at 250/sup 0/C under 15 psia starting nitrogen pressure, over 95% of the wood (maf) was rendered acetone-soluble. The product is a soft, black, bitumen-like solid at room temperature but readily softens at 140/sup 0/C. Between 25 and 50% of the original wood oxygen, depending on alcohol used, was removed as water. Approximately 2 to 17% of the alcohols were retained in the product. Gel permeation chromatography showed that the product's median molecular weight is around 300. Based on experimental and literature results, a mechanism for wood solubilization is proposed. This involves protonation of the etheric oxygen atoms, leading to subsequent bond scission to form carbonium ions which are stabilized by solvent alkoxylation. At severe conditions, polymerization and condensation reactions result in acetone-insoluble materials.

Yu, S.M.

1982-04-01T23:59:59.000Z

309

Solid waste integrated cost analysis model: 1991 project year report  

SciTech Connect

The purpose of the City of Houston's 1991 Solid Waste Integrated Cost Analysis Model (SWICAM) project was to continue the development of a computerized cost analysis model. This model is to provide solid waste managers with tool to evaluate the dollar cost of real or hypothetical solid waste management choices. Those choices have become complicated by the implementation of Subtitle D of the Resources Conservation and Recovery Act (RCRA) and the EPA's Integrated Approach to managing municipal solid waste;. that is, minimize generation, maximize recycling, reduce volume (incinerate), and then bury (landfill) only the remainder. Implementation of an integrated solid waste management system involving all or some of the options of recycling, waste to energy, composting, and landfilling is extremely complicated. Factors such as hauling distances, markets, and prices for recyclable, costs and benefits of transfer stations, and material recovery facilities must all be considered. A jurisdiction must determine the cost impacts of implementing a number of various possibilities for managing, handling, processing, and disposing of waste. SWICAM employs a single Lotus 123 spreadsheet to enable a jurisdiction to predict or assess the costs of its waste management system. It allows the user to select his own process flow for waste material and to manipulate the model to include as few or as many options as he or she chooses. The model will calculate the estimated cost for those choices selected. The user can then change the model to include or exclude waste stream components, until the mix of choices suits the user. Graphs can be produced as a visual communication aid in presenting the results of the cost analysis. SWICAM also allows future cost projections to be made.

Not Available

1991-01-01T23:59:59.000Z

310

The reduction of packaging waste  

Science Conference Proceedings (OSTI)

Nationwide, packaging waste comprises approximately one-third of the waste disposed in sanitary landfills. the US Department of Energy (DOE) generated close to 90,000 metric tons of sanitary waste. With roughly one-third of that being packaging waste, approximately 30,000 metric tons are generated per year. The purpose of the Reduction of Packaging Waste project was to investigate opportunities to reduce this packaging waste through source reduction and recycling. The project was divided into three areas: procurement, onsite packaging and distribution, and recycling. Waste minimization opportunities were identified and investigated within each area, several of which were chosen for further study and small-scale testing at the Hanford Site. Test results, were compiled into five ``how-to`` recipes for implementation at other sites. The subject of the recipes are as follows: (1) Vendor Participation Program; (2) Reusable Containers System; (3) Shrink-wrap System -- Plastic and Corrugated Cardboard Waste Reduction; (4) Cardboard Recycling ; and (5) Wood Recycling.

Raney, E.A.; Hogan, J.J.; McCollom, M.L.; Meyer, R.J.

1994-04-01T23:59:59.000Z

311

Supporting rural wood industry through timber utilization research. Research paper  

SciTech Connect

The report evaluates the potential impact of USDA Forest Service wood utilization and wood energy research on rural employment and income. Recent projections suggest employment will decrease in many forest products industries, such as softwood sawmilling, but will eventually increase in softwood plywood and reconstituated panel mills. Forest products industries expected to provide wages exceeding the average manufacturing production wage include logging, softwood sawmills, millwork, softwood plywood--veneer, structural wood members, particle-board, wood partitions, pulp mills, paper mills, and paperboard mills. Industries expected to pay 90 percent of the average manufacturing production wage include wood kitchen cabinets, mobile homes, prefabricated wood buildings, and wood preservatives.

Skog, K.

1991-10-01T23:59:59.000Z

312

Environmental-performance research priorities: Wood products. Final report  

Science Conference Proceedings (OSTI)

This report describes a research plan to establish environmental, energy, and economic performance measures for renewable building materials, and to identify management and technology alternatives to improve environmental performance in a cost-effective manner. The research plan is designed to: (1) collect environmental and economic data on all life-cycle stages of the materials, (2) ensure that the data follows consistent definitions and collection procedures, and (3) develop analytical procedures for life-cycle analysis to address environmental performance questions. The research will be subdivided into a number of individual project modules. The five processing stages of wood used to organize the research plan are: (1) resource management and harvesting; (2) processing; (3) design and construction of structures; (4) use, maintenance, and disposal; and (5) waste recycling. Individual research module descriptions are provided in the report, as well as assessment techniques, research standards and protocol, and research management. 13 refs., 5 figs., 3 tabs.

NONE

1998-01-15T23:59:59.000Z

313

Inside the guts of wood-eating catfishes: can they digest wood?  

E-Print Network (OSTI)

T (2009) Non-native suckermouth armored catWshes in Florida:Loricariidae), wood-eating armored catWshes from Tropical

German, Donovan P.

2009-01-01T23:59:59.000Z

314

Characterization of household waste in Greenland  

Science Conference Proceedings (OSTI)

The composition of household waste in Greenland was investigated for the first time. About 2 tonnes of household waste was sampled as every 7th bag collected during 1 week along the scheduled collection routes in Sisimiut, the second largest town in Greenland with about 5400 inhabitants. The collection bags were sorted manually into 10 material fractions. The household waste composition consisted primarily of biowaste (43%) and the combustible fraction (30%), including anything combustible that did not belong to other clean fractions as paper, cardboard and plastic. Paper (8%) (dominated by magazine type paper) and glass (7%) were other important material fractions of the household waste. The remaining approximately 10% constituted of steel (1.5%), aluminum (0.5%), plastic (2.4%), wood (1.0%), non-combustible waste (1.8%) and household hazardous waste (1.2%). The high content of biowaste and the low content of paper make Greenlandic waste much different from Danish household waste. The moisture content, calorific value and chemical composition (55 elements, of which 22 were below detection limits) were determined for each material fraction. These characteristics were similar to what has been found for material fractions in Danish household waste. The chemical composition and the calorific value of the plastic fraction revealed that this fraction was not clean but contained a lot of biowaste. The established waste composition is useful in assessing alternative waste management schemes for household waste in Greenland.

Eisted, Rasmus, E-mail: raei@env.dtu.dk [Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby (Denmark); Christensen, Thomas H. [Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby (Denmark)

2011-07-15T23:59:59.000Z

315

Arbuthnott Wood Pellets Ltd | Open Energy Information  

Open Energy Info (EERE)

Arbuthnott Wood Pellets Ltd Arbuthnott Wood Pellets Ltd Jump to: navigation, search Name Arbuthnott Wood Pellets Ltd Place Kincardineshire, Scotland, United Kingdom Zip AB30 1PA Product Wood pellet producer. Coordinates 56.932781°, -2.42531° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":56.932781,"lon":-2.42531,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

316

Wood-Burning Heating System Deduction  

Energy.gov (U.S. Department of Energy (DOE))

This statute allows individual taxpayers a deduction for the purchase and installation of a wood-burning heating system. The deduction is equal to the total cost of purchase and installation for...

317

Chemistry and stoichiometry of wood liquefaction  

DOE Green Energy (OSTI)

The approximate stoichiometry of liquefaction, from data of two PDU runs and a laboratory run is Wood (100 g) + CO (0.1 - 0.4 Mol) ..-->.. CO/sub 2/ (0.5 - 1.0 Mol) + H/sub 2/O (0.4 - 0.8 Mol) + Product (55 - 64 g). Product includes wood oil, water soluble organics and residues. Water is formed by decomposition, carbon dioxide by decomposition and reduction of wood oxygen by CO. Aqueous products include many carboxylic acids plus a roughly equal percentage of non-acids. The wood oil is divided into a neutral fraction and three phenolic fractions of varying molecular weight. Some specific compounds found in water and oil phases are listed.

Davis, H.G.; Kloden, D.J.; Schaleger, L.L.

1981-06-01T23:59:59.000Z

318

Feasibility study of wood-fired cogeneration at a Wood Products Industrial Park, Belington, WV. Phase II  

DOE Green Energy (OSTI)

Customarily, electricity is generated in a utility power plant while thermal energy is generated in a heating/cooling plant; the electricity produced at the power plant is transmitted to the heating/cooling plant to power equipments. These two separate systems waste vast amounts of heat and result in individual efficiencies of about 35%. Cogeneration is the sequential production of power (electrical or mechanical) and thermal energy (process steam, hot/chilled water) from a single power source; the reject heat of one process issued as input into the subsequent process. Cogeneration increases the efficiency of these stand-alone systems by producing these two products sequentially at one location using a small additional amount of fuel, rendering the system efficiency greater than 70%. This report discusses cogeneration technologies as applied to wood fuel fired system.

Vasenda, S.K.; Hassler, C.C.

1992-06-01T23:59:59.000Z

319

Energy implications of the thermal recovery of biodegradable municipal waste materials in the United Kingdom  

SciTech Connect

Highlights: > Energy balances were calculated for the thermal treatment of biodegradable wastes. > For wood and RDF, combustion in dedicated facilities was the best option. > For paper, garden and food wastes and mixed waste incineration was the best option. > For low moisture paper, gasification provided the optimum solution. - Abstract: Waste management policies and legislation in many developed countries call for a reduction in the quantity of biodegradable waste landfilled. Anaerobic digestion, combustion and gasification are options for managing biodegradable waste while generating renewable energy. However, very little research has been carried to establish the overall energy balance of the collection, preparation and energy recovery processes for different types of wastes. Without this information, it is impossible to determine the optimum method for managing a particular waste to recover renewable energy. In this study, energy balances were carried out for the thermal processing of food waste, garden waste, wood, waste paper and the non-recyclable fraction of municipal waste. For all of these wastes, combustion in dedicated facilities or incineration with the municipal waste stream was the most energy-advantageous option. However, we identified a lack of reliable information on the energy consumed in collecting individual wastes and preparing the wastes for thermal processing. There was also little reliable information on the performance and efficiency of anaerobic digestion and gasification facilities for waste.

Burnley, Stephen, E-mail: s.j.burnley@open.ac.uk [Open University, Walton Hall, Milton Keynes MK7 6AA (United Kingdom); Phillips, Rhiannon, E-mail: rhiannon.jones@environment-agency.gov.uk [Strategy Unit, Welsh Assembly Government, Ty Cambria, 29 Newport Road, Cardiff CF24 0TP (United Kingdom); Coleman, Terry, E-mail: terry.coleman@erm.com [Environmental Resources Management Ltd, Eaton House, Wallbrook Court, North Hinksey Lane, Oxford OX2 0QS (United Kingdom); Rampling, Terence, E-mail: twa.rampling@hotmail.com [7 Thurlow Close, Old Town Stevenage, Herts SG1 4SD (United Kingdom)

2011-09-15T23:59:59.000Z

320

How Wood Chip Size Affects Pretreatment Effectiveness of Woody Biomass for Biological Processing  

E-Print Network (OSTI)

explosion pretreatment of wood: effect of chip size, acid,In: Soltes, E.J. (Ed. ), Wood and Agriculture Residues D. , Wegener, G. , 1984. Wood: Chemistry, Ultrastructure,

Tam, Jerry

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

PATTERNS OF DIFFUSIBILITY OF LIGNIN AND CARBOHYDRATE DEGRADING SYSTEMS IN WOOD-ROTTING FUNGI  

E-Print Network (OSTI)

selected Delignification of wood chips by mutant white-rotTemperature relations of wood-destroying fungi. Kaneshiro.phenoloxidases of selected wood-decaying basidiomycetes. J,

Rosenberg, S. L.

2011-01-01T23:59:59.000Z

322

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Using crop straws and wood wastes for paper production should be promoted. Black-Right-Pointing-Pointer Bagasse and textile waste recycling should be properly limited. Black-Right-Pointing-Pointer Imports of scrap paper should be encouraged. Black-Right-Pointing-Pointer Sensitivity analysis, uncertainties and policy implications are discussed. - Abstract: Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China's paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for paper production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment.

Liang Sai [School of Environment, State Key Joint Laboratory of Environment Simulation and Pollution Control, Tsinghua University, Beijing 100084 (China); Zhang, Tianzhu, E-mail: zhangtz@mail.tsinghua.edu.cn [School of Environment, State Key Joint Laboratory of Environment Simulation and Pollution Control, Tsinghua University, Beijing 100084 (China); Xu Yijian [School of Environment, State Key Joint Laboratory of Environment Simulation and Pollution Control, Tsinghua University, Beijing 100084 (China); China Academy of Urban Planning and Design, Beijing 100037 (China)

2012-03-15T23:59:59.000Z

323

Use of Wood Energy in the United States  

E-Print Network (OSTI)

The use of wood for energy including the burning of solid wood and black liquor from pulping has been growing at a rate significantly greater than that for all other uses such as lumber, pulp, or particleboard. in the United States, the end of most wood is not lumber or pulp and paper but feed for energy. In 1983, 155. 5 M Mg of wood were used for energy. This could threaten to increase the price of wood for those other uses, or it can stimulate us to seek more creative ways of using untapped wood resources for fuel. on the basis of estimates of heavy wood energy use relative to other uses for wood, and estimates of continuing high costs for fossil fuels, we suggest here the feasibility of meeting the demand for fuelwood through small-scale cooperatives. Such an approach can improve forestry practices and can avoid unduly increasing the cost of wood for other end uses.

John W. Koning; Kenneth E. Skog

1986-01-01T23:59:59.000Z

324

Wastes and by-products - alternatives for agricultural use  

Science Conference Proceedings (OSTI)

Top address a growing national problem with generation of wastes and by-products, TVA has been involved for several years with developing and commercializing environmentally responsible practices for eliminating, minimizing, or utilizing various wastes/by-products. In many cases, reducing waste generation is impractical, but the wastes/by-products can be converted into other environmentally sound products. In some instances, conversion of safe, value-added agricultural products in the best or only practical alternative. TVA is currently involved with a diversity of projects converting wastes/by-products into safe, economical, and agriculturally beneficial products. Environmental improvement projects have involved poultry litter, cellulosic wastes, used battery acid, ammonium sulfate fines, lead smelting effluents, deep-welled sulfuric acid/ammonium bisulfate solutions, wood ash, waste magnesium ammonium sulfate slurry from recording tape production, and ammunition plant waste sodium nitrate/ammonium nitrate streams.

Boles, J.L.; Craft, D.J.; Parker, B.R.

1994-10-01T23:59:59.000Z

325

International Journal of Engineering & Technology IJET-IJENS Vol: 11 No: 03 7 Co-combustion of Biosolids with Wood Pellets in a  

E-Print Network (OSTI)

Abstract- Co-combustion of biosolids with coal or other biomass fuel can play a significant role in combustion facilities for energy production and waste management policy context. This paper presents the results of an experimental study to investigate the use of biosolids for cocombustion with wood pellets in a wood pellet stove. Fuel property, gas emissions and stove efficiency are compared. In regard to fuel properties, proximate analysis, ultimate analysis and heating values are determined and emissions of carbon monoxide (CO), nitrogen oxides (NOx) and sulphur dioxide (SO2) are measured and compared. Pilot scale combustion tests revealed that cocombustion of 10 % biosolids with 90% wood pellets resulted in successful combustion without any significant degradation of efficiency and emissions. Nitrogen oxides (NOx) emissions were found to be proportional with the N2 content in the fuel. Sulphur dioxide (SO2) emissions were negligible. Index Terms- Biosolids, co-combustion, wood pellet stove, performance and emissions.

Wood Pellet Stove; Murari Mohon Roy; Animesh Dutta; Kenny Corscadden; Peter Havard

2011-01-01T23:59:59.000Z

326

ZERO WASTE.  

E-Print Network (OSTI)

??The aim of the thesis was to develop a clear vision on better waste management system. The thesis introduced the sustainable waste management along with (more)

Upadhyaya, Luv

2013-01-01T23:59:59.000Z

327

Maximization of revenues for power sales from a solid waste resources recovery facility  

Science Conference Proceedings (OSTI)

The report discusses the actual implementation of the best alternative in selling electrical power generated by an existing waste-to-energy facility, the Metro-Dade County Resources Recovery Plant. After the plant processes and extracts various products out of the municipal solid waste, it burns it to produce electrical power. The price for buying power to satisfy the internal needs of our Resources Recovery Facility (RRF) is substantially higher than the power price for selling electricity to any other entity. Therefore, without any further analysis, it was decided to first satisfy those internal needs and then export the excess power. Various alternatives were thoroughly explored as to what to do with the excess power. Selling power to the power utilities or utilizing the power in other facilities were the primary options.

Not Available

1991-12-01T23:59:59.000Z

328

Wood Fuel LP | Open Energy Information  

Open Energy Info (EERE)

Fuel LP Fuel LP Jump to: navigation, search Logo: Wood Fuel LP Name Wood Fuel LP Address 5900 Haynesworth Lane Place Houston, Texas Zip 77034 Sector Biomass Product Wood by-products consulting and marketing Website http://www.woodfuel.com/ Coordinates 29.6221328°, -95.1872605° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":29.6221328,"lon":-95.1872605,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

329

Energy recovery from waste incineration: Assessing the importance of district heating networks  

SciTech Connect

Municipal solid waste incineration contributes with 20% of the heat supplied to the more than 400 district heating networks in Denmark. In evaluation of the environmental consequences of this heat production, the typical approach has been to assume that other (fossil) fuels could be saved on a 1:1 basis (e.g. 1 GJ of waste heat delivered substitutes for 1 GJ of coal-based heat). This paper investigates consequences of waste-based heat substitution in two specific Danish district heating networks and the energy-associated interactions between the plants connected to these networks. Despite almost equal electricity and heat efficiencies at the waste incinerators connected to the two district heating networks, the energy and CO{sub 2} accounts showed significantly different results: waste incineration in one network caused a CO{sub 2} saving of 48 kg CO{sub 2}/GJ energy input while in the other network a load of 43 kg CO{sub 2}/GJ. This was caused mainly by differences in operation mode and fuel types of the other heat producing plants attached to the networks. The paper clearly indicates that simple evaluations of waste-to-energy efficiencies at the incinerator are insufficient for assessing the consequences of heat substitution in district heating network systems. The paper also shows that using national averages for heat substitution will not provide a correct answer: local conditions need to be addressed thoroughly otherwise we may fail to assess correctly the heat recovery from waste incineration.

Fruergaard, T.; Christensen, T.H. [Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby (Denmark); Astrup, T., E-mail: tha@env.dtu.d [Department of Environmental Engineering, Technical University of Denmark, Kongens Lyngby (Denmark)

2010-07-15T23:59:59.000Z

330

Greenhouse gases emission from municipal waste management: The role of separate collection  

Science Conference Proceedings (OSTI)

The municipal solid waste management significantly contributes to the emission in the atmosphere of greenhouse gases (e.g. CO{sub 2}, CH{sub 4}, N{sub 2}O) and therefore the management process from collection to treatment and disposal has to be optimized in order to reduce these emissions. In this paper, starting from the average composition of undifferentiated municipal solid waste in Italy, the effect of separate collection on greenhouse gases emissions from municipal waste management has been assessed. Different combinations of separate collection scenarios and disposal options (i.e. landfilling and incineration) have been considered. The effect of energy recovery from waste both in landfills and incinerators has also been addressed. The results outline how a separate collection approach can have a significant effect on the emission of greenhouse gases and how wise municipal solid waste management, implying the adoption of Best Available Technologies (i.e. biogas recovery and exploitation system in landfills and energy recovery system in Waste to Energy plants), can not only significantly reduce greenhouse gases emissions but, in certain cases, can also make the overall process a carbon sink. Moreover it has been shown that separate collection of plastic is a major issue when dealing with global warming relevant emissions from municipal solid waste management.

Calabro, Paolo S. [Dipartimento di Meccanica e Materiali, Universita degli Studi Mediterranea di Reggio Calabria, via Graziella - loc. Feo di Vito, 89122 Reggio Calabria (Italy)], E-mail: paolo.calabro@unirc.it

2009-07-15T23:59:59.000Z

331

Marin County - Wood Stove Replacement Rebate Program (California...  

Open Energy Info (EERE)

DSIRE1 Summary The County of Marin has created a rebate program to encourage homeowners to remove or replace non-EPA certified wood-burning heaters (wood stoves and...

332

A study of the molecular mechanics of wood cell walls  

E-Print Network (OSTI)

Wood is the original structural material, developed by nature to support tall plants. Every advantageous feature of wood as used in artificial structures is rooted in the plant's evolved capability to withstand the conditions ...

Adler, David, S.M. (David C.). Massachusetts Institute of Technology

2013-01-01T23:59:59.000Z

333

Final Report: Development of Renewable Microbial Polyesters for Cost Effective and Energy- Efficient Wood-Plastic Composites  

SciTech Connect

In this project, we proposed to produce wood fiber reinforced thermoplastic composites (WFRTCs) using microbial thermoplastic polyesters in place of petroleum-derived plastic. WFRTCs are a rapidly growing product area, averaging a 38% growth rate since 1997. Their production is dependent on substantial quantities of petroleum based thermoplastics, increasing their overall energy costs by over 230% when compared to traditional Engineered Wood Products (EWP). Utilizing bio-based thermoplastics for these materials can reduce our dependence on foreign petroleum. We have demonstrated that biopolymers (polyhydroxyalkanoates, PHA) can be successfully produced from wood pulping waste streams and that viable wood fiber reinforced thermoplastic composite products can be produced from these materials. The results show that microbial polyester (PHB in this study) can be extruded together with wastewater-derived cell mass and wood flour into deck products having performance properties comparable to existing commercial HDPE/WF composite products. This study has thus proven the underlying concept that the microbial polyesters produced from waste effluents can be used to make cost-effective and energy-efficient wood-plastic composites. The cost of purified microbial polyesters is about 5-20 times that of HDPE depending on the cost of crude oil, due to high purification (40%), carbon substrate (40%) and sterilized fermentation (20%) costs for the PHB. Hence, the ability to produce competitive and functional composites with unpurified PHA-biomass mixtures from waste carbon sources in unsterile systemswithout cell debris removalis a significant step forward in producing competitive value-added structural composites from forest products residuals using a biorefinery approach. As demonstrated in the energy and waste analysis for the project, significant energy savings and waste reductions can also be realized using this approach. We recommend that the next step for development of useful products using this technology is to scale the technology from the 700-L pilot reactor to a small-scale production facility, with dedicated operation staff and engineering controls. In addition, we recommend that a market study be conducted as well as further product development for construction products that will utilize the unique properties of this bio-based material.

David N. Thompson, Robert W. Emerick, Alfred B. England, James P. Flanders, Frank J. Loge, Katherine A. Wiedeman, Michael P. Wolcott

2010-03-31T23:59:59.000Z

334

International Trade of Wood Pellets (Brochure)  

DOE Green Energy (OSTI)

The production of wood pellets has increased dramatically in recent years due in large part to aggressive emissions policy in the European Union; the main markets that currently supply the European market are North America and Russia. However, current market circumstances and trade dynamics could change depending on the development of emerging markets, foreign exchange rates, and the evolution of carbon policies. This fact sheet outlines the existing and potential participants in the wood pellets market, along with historical data on production, trade, and prices.

Not Available

2013-05-01T23:59:59.000Z

335

Urban Wood-Based Bio-Energy Systems in Seattle  

SciTech Connect

Seattle Steam Company provides thermal energy service (steam) to the majority of buildings and facilities in downtown Seattle, including major hospitals (Swedish and Virginia Mason) and The Northwest (Level I) Regional Trauma Center. Seattle Steam has been heating downtown businesses for 117 years, with an average length of service to its customers of 40 years. In 2008 and 2009 Seattle Steam developed a biomass-fueled renewable energy (bio-energy) system to replace one of its gas-fired boilers that will reduce greenhouse gases, pollutants and the amount of waste sent to landfills. This work in this sub-project included several distinct tasks associated with the biomass project development as follows: a. Engineering and Architecture: Engineering focused on development of system control strategies, development of manuals for start up and commissioning. b. Training: The project developer will train its current operating staff to operate equipment and facilities. c. Flue Gas Clean-Up Equipment Concept Design: The concept development of acid gas emissions control system strategies associated with the supply wood to the project. d. Fuel Supply Management Plan: Development of plans and specifications for the supply of wood. It will include potential fuel sampling analysis and development of contracts for delivery and management of fuel suppliers and handlers. e. Integrated Fuel Management System Development: Seattle Steam requires a biomass Fuel Management System to track and manage the delivery, testing, processing and invoicing of delivered fuel. This application will be web-based and accessed from a password-protected URL, restricting data access and privileges by user-level.

Stan Gent, Seattle Steam Company

2010-10-25T23:59:59.000Z

336

The potential of wood residue streams for industrial wood pellet production in the Baltic Countries and Poland.  

E-Print Network (OSTI)

??Currently most solid biomass in the European Union (EU-27) is made from high grade secondary wood residues, e.g. clean saw dust and wood chips. The (more)

Jong, B. de

2012-01-01T23:59:59.000Z

337

Availability of wood as a heating fuel for Colorado  

SciTech Connect

As Colorado homeowners turn to wood as an alternative space-heating fuel, supplies--particularly along the heavily populated Front Range--dwindle. The report reexamines the resource base and presents alternatives to wood in the event of a shortage (for instance, many wood stoves can burn coal as well).

1982-01-01T23:59:59.000Z

338

Wood Fuel Future: The Potential Web Text December 2010  

E-Print Network (OSTI)

and power, the wood products industry and major independent power producers also have significant production of heat and power. Table 3.1 Canadian Wood Residue Heat & Power Generation - 2003 13 Forest Products SAWMILLS LTD LACRETE 50,000 TONNE WOOD PELLET PRODUCTION IN WESTERN CANADA 2004 / 2005 PINNACLE PEL LET INC

339

The ambient wood journals: replaying the experience  

Science Conference Proceedings (OSTI)

The Ambient Wood project aims to facilitate a learning experience using an adaptive infrastructure in an outdoor environment. This involves sensor technology, virtual world orchestration, and a wide range of devices ranging from hand-held computers to ... Keywords: adaptive infrastructure, consolidation, record and replay, storytelling

Mark J. Weal; Danius T. Michaelides; Mark K. Thompson; David C. DeRoure

2003-08-01T23:59:59.000Z

340

Energie-Cits 2001 BIOMASS-WOOD  

E-Print Network (OSTI)

Energie-Cités 2001 BIOMASS-WOOD Power plant LIENZ Austria By the year 2010, 12% of the gross inland this goal, intensified use needs to be made of biomass, both for heating purposes and for power generation to this rule. Thus, for instance, the town of Lienz started up the largest biomass facility of Austria

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Successful biomass (wood pellets ) implementation in  

E-Print Network (OSTI)

Regional Energy centres in Estonia This presentation will cover Regional Energy Centres in Estonia ! Supply Regional Energy Centres in Estonia Supply of primary energy in Estonia Regional Energy Centres in Estonia of primary energy in Estonia ! Wood fuels production ! Pellet firing projects in Estonia ­ SIDA Demo East

342

Wood combustion systems: status of environmental concerns  

DOE Green Energy (OSTI)

This document addresses the uncertainties about environmental aspects of Wood Combustion Systems that remain to be resolved through research and development. The resolution of these uncertainties may require adjustments in the technology program before it can be commercialized. The impacts and concerns presented in the document are treated generically without reference to specific predetermined sites unless these are known. Hence, site-specific implications are not generally included in the assessment. The report consists of two main sections which describe the energy resource base involved, characteristics of the technology, and introduce the environmental concerns of implementing the technology; and which review the concerns related to wood combustion systems which are of significance for the environment. It also examines the likelihood and consequence of findings which might impede wood commercialization such as problems and uncertainties stemming from current or anticipated environmental regulation, or costs of potential environmental controls. This document is not a formal NEPA document. Appropriate NEPA documentation will be prepared after a formal wood combustion commercialization program is approved by DOE.

Dunwoody, J.E.; Takach, H.; Kelley, C.S.; Opalanko, R.; High, C.; Fege, A.

1980-01-01T23:59:59.000Z

343

Estimating Waste Inventory and Waste Tank Characterization |...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Estimating Waste Inventory and Waste Tank Characterization Estimating Waste Inventory and Waste Tank Characterization Summary Notes from 28 May 2008 Generic Technical Issue...

344

Fast Curing of Composite Wood Products  

SciTech Connect

The overall objective of this program is to develop low temperature curing technologies for UF and PF resins. This will be accomplished by: Identifying the rate limiting UF and PF curing reactions for current market resins; Developing new catalysts to accelerate curing reactions at reduced press temperatures and times. In summary, these new curing technologies will improve the strength properties of the composite wood products and minimize the detrimental effects of wood extractives on the final product while significantly reducing energy costs for wood composites. This study is related to the accelerated curing of resins for wood composites such as medium density fiberboard (MDF), particle board (PB) and oriented strandboard (OSB). The latter is frequently manufactured with a phenol-formaldehyde resin whereas ureaformaldehyde (UF) resins are usually used in for the former two grades of composite wood products. One of the reasons that hinder wider use of these resins in the manufacturing of wood composites is the slow curing speed as well as inferior bondability of UF resin. The fast curing of UP and PF resins has been identified as an attractive process development that would allow wood to be bonded at higher moisture contents and at lower press temperatures that currently employed. Several differing additives have been developed to enhance cure rates of PF resins including the use of organic esters, lactones and organic carbonates. A model compound study by Conner, Lorenz and Hirth (2002) employed 2- and 4-hydroxymethylphenol with organic esters to examine the chemical basis for the reported enhanced reactivity. Their studies suggested that the enhance curing in the presence of esters could be due to enhanced quinone methide formation or enhanced intermolecular SN2 reactions. In either case the esters do not function as true catalysts as they are consumed in the reaction and were not found to be incorporated in the polymerized resin product. An alternative approach to accelerated PF curing can be accomplished with the addition amines or amides. The later functionality undergoes base catalyzed hydrolysis yielding the corresponding carboxyl ate and free amine which rapidly reacts with the phenolic methylol groups facilitating polymerization and curing of the PF resin (Pizzi, 1997).

Dr. Arthur J. Ragauskas

2006-04-26T23:59:59.000Z

345

Effect of species and wood to bark ratio on pelleting of southern woods  

Science Conference Proceedings (OSTI)

Six common southern hardwoods and loblolly pine were pelleted in a laboratory pellet mill. The pellet furnishes were blended to test the effect of different wood to bark ratios on pellet durability and production rate. Included was a ratio chosen to simulate the wood to bark ratio found in whole-tree chips. This furnish produced good quality pellets for all species tested. Pelleting of the pure wood of hardwoods was not successful; furnish routinely blocked the pellet mill dies. Pure pine wood, however, did produce acceptable pellets. It was noted that, as lignin and extractive content increased above a threshold level, the precentage of fines produced in a pellet durability test increased. Thus, all pine and tupelo wood/bark mixes produces high fines. This reduces the desirability of the pellets in the marketplace. Further research is necessary to confirm this relationship. This study suggests that both tree species and wood/bark ratio affect the durability of pellets and the rate with which they can be produced in a laboratory pellet mill. 9 references.

Bradfield, J.; Levi, M.P.

1984-01-01T23:59:59.000Z

346

Near-term potential of wood as a fuel  

DOE Green Energy (OSTI)

A summary of near-term conversion technologies, which could be used to expand utilization of wood residues and standing forests, is presented. The forest products industry is identified as a principal candidate for expanded wood-fuel use. Sources of wood-fuel are identified and conversion technologies and costs are discussed. Possible near-term incentives to encourage the use of wood as a fuel are examined. These incentives include a retirement tax credit and an investment tax credit. Suppliers of commercial wood conversion systems are identified.

Salo, D.; Gsellman, L.; Medville, D.; Price, G.

1978-08-01T23:59:59.000Z

347

Analysis of energy recovery potential using innovative technologies of waste gasification  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer Energy recovery from waste by gasification was simulated. Black-Right-Pointing-Pointer Two processes: high temperature gasification and gasification associated to plasma. Black-Right-Pointing-Pointer Two types of feeding waste: Refuse Derived Fuel (RDF) and pulper residues. Black-Right-Pointing-Pointer Different configurations for the energy cycles were considered. Black-Right-Pointing-Pointer Comparison with performances from conventional Waste-to-Energy process. - Abstract: In this paper, two alternative thermo-chemical processes for waste treatment were analysed: high temperature gasification and gasification associated to plasma process. The two processes were analysed from the thermodynamic point of view, trying to reconstruct two simplified models, using appropriate simulation tools and some support data from existing/planned plants, able to predict the energy recovery performances by process application. In order to carry out a comparative analysis, the same waste stream input was considered as input to the two models and the generated results were compared. The performances were compared with those that can be obtained from conventional combustion with energy recovery process by means of steam turbine cycle. Results are reported in terms of energy recovery performance indicators as overall energy efficiency, specific energy production per unit of mass of entering waste, primary energy source savings, specific carbon dioxide production.

Lombardi, Lidia, E-mail: lidia.lombardi@unifit.it [Dipartimento di Energetica, University of Florence, via Santa Marta 3, 50139 Florence (Italy); Carnevale, Ennio [Dipartimento di Energetica, University of Florence, via Santa Marta 3, 50139 Florence (Italy); Corti, Andrea [Dipartimento di Ingegneria dell'Informazione, University of Siena, via Roma 56, 56100 Siena (Italy)

2012-04-15T23:59:59.000Z

348

Process and technological aspects of municipal solid waste gasification. A review  

Science Conference Proceedings (OSTI)

Highlights: Black-Right-Pointing-Pointer Critical assessment of the main commercially available MSW gasifiers. Black-Right-Pointing-Pointer Detailed discussion of the basic features of gasification process. Black-Right-Pointing-Pointer Description of configurations of gasification-based waste-to-energy units. Black-Right-Pointing-Pointer Environmental performance analysis, on the basis of independent sources data. - Abstract: The paper proposes a critical assessment of municipal solid waste gasification today, starting from basic aspects of the process (process types and steps, operating and performance parameters) and arriving to a comparative analysis of the reactors (fixed bed, fluidized bed, entrained bed, vertical shaft, moving grate furnace, rotary kiln, plasma reactor) as well as of the possible plant configurations (heat gasifier and power gasifier) and the environmental performances of the main commercially available gasifiers for municipal solid wastes. The analysis indicates that gasification is a technically viable option for the solid waste conversion, including residual waste from separate collection of municipal solid waste. It is able to meet existing emission limits and can have a remarkable effect on reduction of landfill disposal option.

Arena, Umberto, E-mail: umberto.arena@unina2.it [Department of Environmental Sciences, Second University of Naples, Via A. Vivaldi, 43, 81100 Caserta (Italy)

2012-04-15T23:59:59.000Z

349

Wood and energy in New Hampshire. Staff report  

SciTech Connect

Telephone surveys of New Hampshire households conducted in 1979 and 1980 indicate a transition to wood heating in response to a series of conventional energy price increases and uncertainty in conventional energy supplies. New Hampshire households consumed 394,000 cords of wood in the winter of 1978-79; 504,000 cords were burnt during the next winter. The airtight wood stove has become the most commonly used wood-burning apparatus. Survey data of residential wood cutting, purchasing, and burning were analyzed by household tenure, wood-burning apparatus, and county. Residential use of wood for energy constitutes a new demand on the forest resource, increases local income and employment, displaces fuel oil and electricity, and may compromise household safety.

Bailey, M.R.; Wheeling, P.R.

1982-06-01T23:59:59.000Z

350

Energy Information Directory of the Energy Information Administration  

U.S. Energy Information Administration (EIA)

Waste to energy; Waste management; Water companies; Water conservation apparatus; Weather; Weatherization material; Weatherization Program; Western Area Power ...

351

Developing an energy efficiency service industry in Shanghai  

E-Print Network (OSTI)

vast potential of reducing energy waste and improving energyindustrial sector (e.g. , waste-to-energy, compressed air,

Lin, Jiang; Goldman, Charles; Levine, Mark; Hopper, Nicole

2004-01-01T23:59:59.000Z

352

Wood power - its potential in our energy crisis  

Science Conference Proceedings (OSTI)

Wood is meeting about 2% of total U.S. energy needs and may eventually supply up to 7% of our nation's energy. Many forms of direct combustion equipment are available for residential heating and range from supplemental wood-burning stoves to complete house-heating multi-fuel furnaces. A recent survey conducted in New York indicated that one-third of the people contacted used wood for home heating. The total amount of fuelwood used in New York State in 1978 amounted to 1,716,000 standard cords. A Wisconsin study indicates that more than 1.2 million cords of firewood were burned by Wisconsin households during the 1979-80 heating season. A Pennsylvania survey indicated that 22% of single family households used wood for home heating. Corning Glass Works recently conducted a wood-burning stove market survey and found that 18% of all U.S. households own wood-burning stoves. On the basis of cost per unit of heat, wood heat is cheaper than its next closest commonly available rival (fuel oil) and is also cheaper than anthracite coal and electricity. Industrial wood-burning furnaces are commonly incorporated into boiler systems. Nearly 1700 wood-fired boiler systems are in operation in the United States. The economic value of a wood fuel will depend on its heating value and moisture content. For an indsutry considering use of densified wood for fuel, there is a question of whether the added expense is justified by increased ease of handling and improved burning efficiency. Where high sulfur emissions from coal are a problem, burning sulfur-free pellets in combination with coal may be a solution. In Maine a $3 million pellet-making plant is producing 600 tons of pellets per day. Nationally, the overall generating capacity of all known electrical generating plants using wood and wood derived fuels is about 4500 megawatts. Wood can be processed to produce liquid fuels and other chemicals.

Johnson, W.W.

1982-01-01T23:59:59.000Z

353

Waste Equals Food: Developing a Sustainable Agriculture Support Cluster for a Proposed Resource Recovery Park in Puerto Rico  

E-Print Network (OSTI)

This paper analyzes and makes recommendations for plans to develop an eco-industrial park (EIP) in Puerto Rico. This project began with two basic goals: first, to supply cheaper energy to the island, which has suffered economic losses due to expensive energy; and second, to deal with the solid waste management problem. Thus, a proposal for a waste-to-energy (WTE) facility entered the picture, and close behind came an ambitious plan to convert the surrounding area into an EIP to be called the Renova Resource Recovery Park (RRRP). The EIP has been designed to include industries such as an existing paper mill, a steel casting plant, and a cement kiln. However, given the fact that the proposed site of RRRP is on abandoned sugar cane land, a new member was proposed a sustainable agriculture cluster.

Alethea Abuyuan; Iona Hawken; Michael Newkirk; Roger Williams

1999-01-01T23:59:59.000Z

354

Comparing the greenhouse gas emissions from three alternative waste combustion concepts  

Science Conference Proceedings (OSTI)

Highlights: Black-Right-Pointing-Pointer Significant GHG reductions are possible by efficient WtE technologies. Black-Right-Pointing-Pointer CHP and high power-to-heat ratio provide significant GHG savings. Black-Right-Pointing-Pointer N{sub 2}O and coal mine type are important in LCA GHG emissions of FBC co-combustion. Black-Right-Pointing-Pointer Substituting coal and fuel oil by waste is beneficial in electricity and heat production. Black-Right-Pointing-Pointer Substituting natural gas by waste may not be reasonable in CHP generation. - Abstract: Three alternative condensing mode power and combined heat and power (CHP) waste-to-energy concepts were compared in terms of their impacts on the greenhouse gas (GHG) emissions from a heat and power generation system. The concepts included (i) grate, (ii) bubbling fluidised bed (BFB) and (iii) circulating fluidised bed (CFB) combustion of waste. The BFB and CFB take advantage of advanced combustion technology which enabled them to reach electric efficiency up to 35% and 41% in condensing mode, respectively, whereas 28% (based on the lower heating value) was applied for the grate fired unit. A simple energy system model was applied in calculating the GHG emissions in different scenarios where coal or natural gas was substituted in power generation and mix of fuel oil and natural gas in heat generation by waste combustion. Landfilling and waste transportation were not considered in the model. GHG emissions were reduced significantly in all of the considered scenarios where the waste combustion concepts substituted coal based power generation. With the exception of condensing mode grate incinerator the different waste combustion scenarios resulted approximately in 1 Mton of fossil CO{sub 2}-eq. emission reduction per 1 Mton of municipal solid waste (MSW) incinerated. When natural gas based power generation was substituted by electricity from the waste combustion significant GHG emission reductions were not achieved.

Vainikka, Pasi, E-mail: pasi.vainikka@vtt.fi [VTT, Koivurannantie 1, FIN 40101 Jyvaeskylae (Finland); Tsupari, Eemeli; Sipilae, Kai [VTT, Koivurannantie 1, FIN 40101 Jyvaeskylae (Finland); Hupa, Mikko [Aabo Akademi Process Chemistry Centre, Piispankatu 8, FIN 20500 Turku (Finland)

2012-03-15T23:59:59.000Z

355

Solid waste integrated cost analysis model: 1991 project year report. Part 2  

SciTech Connect

The purpose of the City of Houston`s 1991 Solid Waste Integrated Cost Analysis Model (SWICAM) project was to continue the development of a computerized cost analysis model. This model is to provide solid waste managers with tool to evaluate the dollar cost of real or hypothetical solid waste management choices. Those choices have become complicated by the implementation of Subtitle D of the Resources Conservation and Recovery Act (RCRA) and the EPA`s Integrated Approach to managing municipal solid waste;. that is, minimize generation, maximize recycling, reduce volume (incinerate), and then bury (landfill) only the remainder. Implementation of an integrated solid waste management system involving all or some of the options of recycling, waste to energy, composting, and landfilling is extremely complicated. Factors such as hauling distances, markets, and prices for recyclable, costs and benefits of transfer stations, and material recovery facilities must all be considered. A jurisdiction must determine the cost impacts of implementing a number of various possibilities for managing, handling, processing, and disposing of waste. SWICAM employs a single Lotus 123 spreadsheet to enable a jurisdiction to predict or assess the costs of its waste management system. It allows the user to select his own process flow for waste material and to manipulate the model to include as few or as many options as he or she chooses. The model will calculate the estimated cost for those choices selected. The user can then change the model to include or exclude waste stream components, until the mix of choices suits the user. Graphs can be produced as a visual communication aid in presenting the results of the cost analysis. SWICAM also allows future cost projections to be made.

Not Available

1991-12-31T23:59:59.000Z

356

Hazardous Waste  

Science Conference Proceedings (OSTI)

Table 6   General refractory disposal options...D landfill (b) Characterized hazardous waste by TCLP

357

Inexpensive solar-wood water heating combinations  

SciTech Connect

A promising batch heater recently built and now being tested consists of lengths of eight-inch galvanized culvert pipe painted with semiselective black coating, hooked in series and tied in as part of a passive closed loop, unpressurized solar-wood water heating combination. One 10-foot length of eight-inch culvert contains 14.6 gallons of water. Eight-inch culvert provides a near optimum surface area per unit volume ratio, resulting in quicker, more efficient solar water heating. Moreover, the proposed arrangement minimizes the mixing of hot with cold water as warm water is used, often a problem with many types of batch heaters. Details for constructing this type of batch heater are provided. The system is an unpressurized, closed loop set-up, which means that the same liquid circulates continually from solar heater to wood heater to storage tank heat exchanger. The collector design is a variation on the inverted batch heater which takes its inspiration from a number of solar designers of similar units and introduces several additional measures to take advantage of the wood heating connection and to improve the design based on operating experience.

Poitras, R.

1980-01-01T23:59:59.000Z

358

Leonard Wood and the American Empire  

E-Print Network (OSTI)

During the ten years following the Spanish American War (1898 to 1908), Major General Leonard Wood served as the primary agent of American imperialism. Wood was not only a proconsul of the new American Empire; he was a symbol of the empire and the age in which he served. He had the distinction of directing civil and military government in Cuba and the Philippines where he implemented the imperial policies given to him by the administrations of William McKinley and Theodore Roosevelt. In Cuba, he labored to rebuild a state and a civil society crippled by decades of revolutionary ferment and guided the administration's policy through the dangerous channels of Cuban politics in a way that satisfied at least to the point of avoiding another revolution both the Cubans and the United States. In the Philippines, Wood took control of the Moro Province and attempted to smash the tribal-religious leadership of Moro society in order to bring it under direct American rule. His personal ideology, the imperial policies he shepherded, and the guidance he provided to fellow military officers and the administrations he served in matters of colonial administration and defense shaped the American Empire and endowed it with his personal stamp.

Pruitt, James Herman

2011-05-01T23:59:59.000Z

359

Biohazardous Waste Disposal Guidelines Sharps Waste Solid Lab Waste Liquid Waste Animals Pathological Waste  

E-Print Network (OSTI)

Biohazardous Waste Disposal Guidelines Sharps Waste Solid Lab Waste Liquid Waste Animals Pathological Waste Description Biohazard symbol Address: UCSD 9500 Gilman Drive La Jolla, CA 92093 (858) 534) and identity of liquid waste Biohazard symbol Address: UCSD 9500 Gilman Drive La Jolla, CA 92093 (858) 534

Russell, Lynn

360

Biohazardous Waste Disposal Guidelines Sharps Waste Solid Lab Waste Liquid Waste Animals Pathological Waste  

E-Print Network (OSTI)

2/2009 Biohazardous Waste Disposal Guidelines Sharps Waste Solid Lab Waste Liquid Waste Animals Pathological Waste Description Biohazard symbol Address: UCSD 200 West Arbor Dr. San Diego, CA 92103 (619 (9:1) OR Biohazard symbol (if untreated) and identity of liquid waste Biohazard symbol Address

Firtel, Richard A.

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Regenerao de Floresta Secundria Eric A. Davidson Woods...  

NLE Websites -- All DOE Office Websites (Extended Search)

299 a 309. 1 Limitaes de Nutrientes para a Regenerao de Floresta Secundria Eric A. Davidson Woods Hole Research Center, Falmouth, Massachusetts, USA Luiz A. Martinelli...

362

Water Sampling At Little Valley Area (Wood, 2002) | Open Energy...  

Open Energy Info (EERE)

Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Water Sampling At Little Valley Area (Wood, 2002) Exploration Activity Details Location...

363

Wood County Electric Coop, Inc | Open Energy Information  

Open Energy Info (EERE)

Wood County Electric Coop, Inc Place Texas Utility Id 20927 Utility Location Yes Ownership C NERC Location SPP NERC SPP Yes Activity Transmission Yes Activity Distribution Yes...

364

Wood-boring Insects of Trees and Shrubs  

E-Print Network (OSTI)

This publication explains how to identify and control wood-boring insects that invade shrubs and shade trees in Texas. 12 pages, 9 figures, 6 photographs, 1 table

Drees, Bastiaan M.; Jackman, John A.; Merchant, Michael E.

2008-06-17T23:59:59.000Z

365

Graphite/Copper Composites from Natural Wood Precursors  

Science Conference Proceedings (OSTI)

Graphite derived from natural wood precursors provides a uniquely anisotropic porous scaffold for the fabrication of graphite/copper composites. The wettability...

366

The Viscoelastic Properties of Wood Cell Walls after Minimally ...  

Science Conference Proceedings (OSTI)

Samples were prepared on dried wood with no embedding resin within the cellular structure. Four types of analysis methods were used; the standard method,...

367

City of Wood River, Nebraska (Utility Company) | Open Energy...  

Open Energy Info (EERE)

Nebraska (Utility Company) Jump to: navigation, search Name City of Wood River Place Nebraska Utility Id 20945 Utility Location Yes Ownership M NERC Location MRO NERC SPP Yes...

368

Hazardous Waste Program (Alabama)  

Energy.gov (U.S. Department of Energy (DOE))

This rule states criteria for identifying the characteristics of hazardous waste and for listing hazardous waste, lists of hazardous wastes, standards for the management of hazardous waste and...

369

Section 7.1.3 Wood Products: Greening Federal Facilities; Second...  

NLE Websites -- All DOE Office Websites (Extended Search)

wood is being used in a building, there is an opportunity to advance good forest management by specifying certified wood products. When wood is be- ing used for framing-more...

370

How Wood Chip Size Affects Pretreatment Effectiveness of Woody Biomass for Biological Processing  

E-Print Network (OSTI)

Parameters employed for heating of wood chips employed inParameters employed for heating of wood chips employed inW.T. , 2006. Estimating heating times of wood boards, square

Tam, Jerry

2013-01-01T23:59:59.000Z

371

Life in the woods : production and consumption of the urban forest  

E-Print Network (OSTI)

The use of wood is fraught with paradox. Wood as a building material is embraced for its naturalness, while the cutting of trees is indicted as a destruction of nature. Wood is lauded for its structural properties and ...

Volicer, Nadine (Nadine M.)

2012-01-01T23:59:59.000Z

372

Wood Pellet Heating Systems: The Earthscan Expert Handbook of Planning, Design and Installation  

Science Conference Proceedings (OSTI)

Wood Pellet Heating Systems is a comprehensive handbook covering all aspects of wood pellet heating technology. The use of wood pellets as an alternative heating fuel is already well established in several countries and is becoming widespread as fossil ...

Dilwyn Jenkins

2010-04-01T23:59:59.000Z

373

My voice shall fill the woods : Lydgate, poetic authority, and the canonization of Philomela  

E-Print Network (OSTI)

My Voice Shall Fill the Woods: Lydgate, Poetic Authority,My Voice Shall Fill the Woods: Lydgate, Poetic Authority,the nightingale fills the woods with song, beautiful and

Gillespie, Mary Elizabeth

2010-01-01T23:59:59.000Z

374

Digestive enzyme activities and gastrointestinal fermentation in wood-eating catfishes  

E-Print Network (OSTI)

our data on wild-caught wood-eating catWshes appear to bein the Amazo- nian basin, and the wood-eating species likelyby reducing the particle size of wood from coarse debris to

German, Donovan P.; Bittong, Rosalie A.

2009-01-01T23:59:59.000Z

375

North Woods River: The St. Croix River in Upper Midwest History  

E-Print Network (OSTI)

Review: North Woods River: The St. Croix River in Upperand Karamanski, Theodore J. North Woods River: The St. Croixbeauty and splendor. In North Woods River, Eileen M. McMahon

Karalus, Daniel E

2011-01-01T23:59:59.000Z

376

Metagenomic and functional analysis of hindgut microbiota of a wood-feeding higher termite  

E-Print Network (OSTI)

and western branches of the Wood/Ljungdahl pathway: how the1993). 55. Wood, T. Preparation of crystalline,of hindgut microbiota of a wood-feeding higher termite Falk

Warnecke, Falk

2008-01-01T23:59:59.000Z

377

Daughters of Dissent: Women as Warriors in Sembene Ousmane's God's Bits of Wood  

E-Print Network (OSTI)

Sembene. Gods Bits of Wood. Heinemann, Soyinka, Wole. Myth,novel, God's Bits of Wood, with particular reference to theOusmane's novel, God's Bits of Wood. It is important to note

Abdurrahman, Umar

2004-01-01T23:59:59.000Z

378

Save the tree of life or get lost in the woods  

E-Print Network (OSTI)

of life or get lost in the woods Biology Direct 2010, 5:44of life or get lost in the woods Ruben E Valas* 1 and PhilipOtherwise one gets lost in the woods of neutral evolution.

Valas, Ruben E; Bourne, Philip E

2010-01-01T23:59:59.000Z

379

The use of a permanent magnet for water content measurements of wood chips  

E-Print Network (OSTI)

Water Content Measurements of Wood Chips * P. J. Barale, C.measures the water content of wood chips, pulp and brownwater content measurements in wood chips in a magnetic field

2001-01-01T23:59:59.000Z

380

Wood Pulp Digetster Wall Corrosion Investigation  

DOE Green Energy (OSTI)

The modeling of the flow in a wood pulp digester is but one component of the investigation of the corrosion of digesters. This report describes the development of a Near-Wall-Model (NWM) that is intended to couple with a CFD model that determines the flow, heat, and chemical species transport and reaction within the bulk flow of a digester. Lubrication theory approximations were chosen from which to develop a model that could determine the flow conditions within a thin layer near the vessel wall using information from the interior conditions provided by a CFD calculation of the complete digester. The other conditions will be determined by coupled solutions of the wood chip, heat, and chemical species transport and chemical reactions. The NWM was to couple with a digester performance code in an iterative fashion to provide more detailed information about the conditions within the NW region. Process Simulations, Ltd (PSL) is developing the digester performance code. This more detailed (and perhaps more accurate) information from the NWM was to provide an estimate of the conditions that could aggravate the corrosion at the wall. It is intended that this combined tool (NWM-PSL) could be used to understand conditions at/near the wall in order to develop methods to reduce the corrosion. However, development and testing of the NWM flow model took longer than anticipated and the other developments (energy and species transport, chemical reactions and linking with the PSL code) were not completed. The development and testing of the NWM are described in this report. In addition, the investigation of the potential effects of a clear layer (layer reduced in concentration of wood chips) near the wall is reported in Appendix D. The existence of a clear layer was found to enhance the flow near the wall.

Giles, GE

2003-09-18T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Wood Fired Steam Plants in Georgia  

E-Print Network (OSTI)

During the 1970's, Georgia industry experienced problems obtaining fuel for operations on several occasions. In particular, the very cold winter of 1976-77 resulted in natural gas curtailments which virtually shut down many of Georgia's industries. Shortly after that time, Georgia Tech and the Georgia Forestry Commission embarked on a number of projects directed toward providing the use of wood as an industrial energy source. This paper will present an overview of these programs with an emphasis on three demonstration plants that were built with partial financing by state and federal government.

Bulpitt, W. S.

1983-01-01T23:59:59.000Z

382

Waste= Capital.  

E-Print Network (OSTI)

??The evolution of manufacturing practices over the last century has led to the creation of excess waste during the production process, depleting resources and overwhelming (more)

Stidham, Steve P.

2011-01-01T23:59:59.000Z

383

Modeling and Rendering Physically-Based Wood Combustion  

Science Conference Proceedings (OSTI)

Rendering of wood combustion has received some attention recently, but prior work has not incorporated effects of internal wood properties such as density variation (i.e. "grain") and pre-combustion processes such as drying. In this paper we present ...

Roderick M. Riensche; Robert R. Lewis

2009-11-01T23:59:59.000Z

384

www.eia.gov  

U.S. Energy Information Administration (EIA)

Wood and Wood-derived fuels include wood/wood waste solids (including paper pellets, railroad ties, utility poles, wood chips, bark, and wood waste solids), ...

385

www.eia.gov  

U.S. Energy Information Administration (EIA)

Wood and wood-derived fuels include wood/wood waste solids (including paper pellets, railroad ties, utility poles, wood chips, bark, and wood waste solids), ...

386

A Wood-Fired Gas Turbine Plant  

E-Print Network (OSTI)

This paper covers the research and development of a wood-fired gas turbine unit that is used for generating electricity. The system uses one large cyclonic combustor and a cyclone cleaning system in series to provide hot gases to drive an Allison T-56 aircraft engine (the industrial version is the 501-k). A Westinghouse 3,000-kW generator is used on the prototype facility with a Philadelphia gear system reducing the 14,000-rpm turbine output speed to the 3,600-rpm generator operating speed. Fuel is fed into the combustor by a rotary valve system. The swirling effect of the cyclone combustor ensures that residence time is adequate to completely burn all solid particles in the combustor ahead of the cyclone filter. Burning of particles on the metal walls of the cyclone filter could cause overheating and deterioration of the walls. This wood-fired gas turbine unit could provide a low cost source of power for areas where conventional methods are now prohibitive and provide a means for recovering energy from a source that now poses disposal problems.

Powell, S. H.; Hamrick, J. T.

1986-06-01T23:59:59.000Z

387

Silviculture: growing more wood on less land  

SciTech Connect

Maximizing the production of a concentrated, homogeneous wood supply virtually dictates intensively managed plantations. This management system implies: (1) improving the composite genotype of plantation trees; (2) optimizing their morphological and physiological condition prior to and at planting time; (3) improving the physiological environment of the crop at all stages of development; (4) protecting the plantation from pests and catastrophic events; and (5) modifying the shapes, dimensions, and qualities of crop trees to enhance the utility and value of harvested timber. Beneficiation of forest residuals for fiber and fuel is pushing forest industry relentlessly toward total stand utilization. Relative to the productivity of undisturbed or partially logged humid tropical forests, plantation growth rates represent four-fold to ten-fold increases in volume production. Displacement of some proportion of shifting agriculture and natural forest management systems by intensively managed plantations is desirable and biologically feasible. A key to successful tropical forest management and preservation is population stability, a condition toward which integrated wood conversion facilities supplied by a reliable plantation system can make a major contribution. There are some pressing and many esoteric reasons for conserving forest resources but pressures for utilizing and renewing these resources are immediate and unavoidable.

Gladstone, W.T.

1980-01-01T23:59:59.000Z

388

Municipal solid waste management: A bibliography of US Department of Energy contractor reports through 1993  

Science Conference Proceedings (OSTI)

US Department of Energy contractors continue to conduct research targeting the productive and responsible use of the more than 536,000 tons of municipal solid waste (MSW) that is generated each day in the United States. It is becoming more and more prudent to improve current methods of MSW management and to continue to search for additional cost-effective, energy-efficient means to manage our MSW resource. This bibliography is an updated version of Municipal Waste to Energy: An Annotated Bibliography of US Department of Energy Contractor Reports, by Caroline Brooks, published in 1987. Like its predecessor, this bibliography provides information about technical reports on energy from municipal waste that were prepared under grants or contracts from the US Department of Energy. The reports listed focus on energy from municipal waste technologies and energy conservation in wastewater treatment. The bibliography contains three indexes -- an author index, a subject index, and a title index. The reports are listed alphabetically in the subject areas and may appear under more than one subject. All of the reports cited in the original MSW bibliography are also included in this update. The number of copies of each report originally published varied according to anticipated public demand. However, all reports are available in either microfiche or hard copy form and may be ordered from the National Technical Information Service (NTIS), US Department of Commerce, Springfield, VA 22161. Explicit information on ordering reports is included in Appendix A.

Shepherd, P.

1994-07-01T23:59:59.000Z

389

MUSHROOM WASTE MANAGEMENT PROJECT LIQUID WASTE MANAGEMENT  

E-Print Network (OSTI)

#12;MUSHROOM WASTE MANAGEMENT PROJECT LIQUID WASTE MANAGEMENT PHASE I: AUDIT OF CURRENT PRACTICE The Mushroom Waste Management Project (MWMP) was initiated by Environment Canada, the BC Ministry of solid and liquid wastes generated at mushroom producing facilities. Environmental guidelines

390

NREL: News Feature - Wood-Boring Gribbles Intrigue Researchers  

NLE Websites -- All DOE Office Websites (Extended Search)

Wood-Boring Gribbles Intrigue Researchers Wood-Boring Gribbles Intrigue Researchers July 24, 2013 This is a light-enhanced close-up of a tiny crustacean's head and torso, with what looks like fluorescent-blue antennae. Three of its legs are showing. Enlarge image A gribble is a tiny wood borer that produces its own enzyme that can devastate wood efficiently. Researchers hope that by studying gribbles they can learn ways to improve the process of turning biomass into liquid fuels. Courtesy Laura Michie, University of Portsmouth, United Kingdom Tiny wood borers known colloquially as gribbles make their own enzymes and use them to eat through docks in harbor towns, earning enmity from fishermen all around the world. Now, researchers from the Energy Department's National Renewable Energy Laboratory (NREL) and elsewhere are exploring whether that curse can be

391

Steam gasification of wood in the presence of catalysts  

SciTech Connect

Catalytic steam gasification of wood, including sawdust, chipped forest slash, and mill shavings, is being investigated. Results of laboratory, process development unit (PDU), and feasibility studies illustrate attractive processes for conversion of wood to methanol and a substitute natural gas (SNG). Recent laboratory studies developed a long-lived alloy catalyst for generation of a methanol synthesis gas by steam gasification of wood. Modification of the PDU for operation at 10 atm (150 psia) is nearly complete. The modified PDU will be operated at the elevated pressure to confirm yields and design parameters used in process feasibility studies. Feasibility studies were completed on wood-to-methane (SNG) and wood-to-methanol plants with capacities of 2000 and 200 oven dried tons (1800 and 180 metric t) per day using catalytic gasification. The results showed that generation of methanol on the large scale is economically viable today while SNG generation is competitive with future prices.

Mitchell, D.H.; Mudge, L.K.; Baker, E.G.

1981-01-01T23:59:59.000Z

392

Performance of bolted wood connections using supplemental confining devices  

E-Print Network (OSTI)

In the aftermath of the 1994 Northridge Earthquake, extensive field investigations revealed damage in wood frame construction in the form of splitting the 2x4 or 2x6 dimension lumber sill plates along the line of anchor bolts which typically connect shear walls to the masonry or concrete foundation. This paper presents an experimental investigation on the performance of bolted wood connections at the yield and ultimate limit states during monotonic and incremental quasi-static reversed cyclic loading and suggests possible retrofit strategies for their improved seismic performance. Proposed retrofit strategies are based on providing confinement to the bolted wood member using metal reinforcing ;traps and reinforcing clamps to increase the deformation capability and energy dissipation capacity of the connection, while maintaining substantial levels of connection strength. Connection types included in the investigation are: (1) double shear wood-to-wood connections; and (2) single shear simulated sill plate-to-concrete foundation connections.

Stromatt, Rebecca Faye

1996-01-01T23:59:59.000Z

393

Biomass plants face wood supply risks Report warns giant new biomass power plants will be hugely reliant on wood chip  

E-Print Network (OSTI)

Biomass plants face wood supply risks Report warns giant new biomass power plants will be hugely's biomass energy sector could be undermined unless businesses move to resolve the supply chain issues-scale biomass plants will leave generators largely reliant on biomass from overseas such as wood chips, elephant

394

WASTE DISPOSAL WORKSHOPS: ANTHRAX CONTAMINATED WASTE  

E-Print Network (OSTI)

WASTE DISPOSAL WORKSHOPS: ANTHRAX CONTAMINATED WASTE January 2010 Prepared for the Interagency DE-AC05-76RL01830 Waste Disposal Workshops: Anthrax-Contaminated Waste AM Lesperance JF Upton SL #12;#12;PNNL-SA-69994 Waste Disposal Workshops: Anthrax- Contaminated Waste AM Lesperance JF Upton SL

395

Chapter 1. Net Generation - Energy Information Administration  

U.S. Energy Information Administration (EIA)

1 Wood/wood waste solids (including paper pellets, railroad ties, utility poles, wood chips, bark, and wood waste solids), wood waste liquids (red liquor, ...

396

Implementing Strategies for Drying and Pressing Wood Without Emissions Controls  

DOE Green Energy (OSTI)

Drying and pressing wood for the manufacture of lumber, particleboard, oriented strand board (OSB), veneer and medium density fiberboard (MDF) release volatile organic compounds (VOCs) into the atmosphere. These emissions require control equipment that are capital-intensive and consume significant quantities of natural gas and electricity. The objective of our work was to understand the mechanisms through which volatile organic compounds are generated and released and to develop simple control strategies. Of the several strategies developed, two have been implemented for OSB manufacture over the course of this study. First, it was found that increasing final wood moisture by about 2-4 percentage points reduced the dryer emissions of hazardous air pollutants by over 70%. As wood dries, the escaping water evaporatively cools the wood. This cooling tapers off wood when the wood is nearly dry and the wood temperature rises. Thermal breakdown of the wood tissue occurs and VOCs are released. Raising the final wood moisture by only a few percentage points minimizes the temperature rise and reduces emissions. Evaporative cooling also impacts has implications for VOC release from wood fines. Flaking wood for OSB manufacture inevitable generates fines. Fines dry out rapidly because of their high surface area and evaporative cooling is lost more rapidly than for flakes. As a result, fines emit a disproportionate quantity of VOCs. Fines can be reduced in two ways: through screening of the green furnish and through reducing their generation during flaking. The second approach is preferable because it also increased wood yield. A procedure to do this by matching the sharpness angle of the flaker knife to the ambient temperature was also developed. Other findings of practical interests are as follows: Dielectric heating of wood under low-headspace conditions removes terpenes and other extractives from softwood; The monoterpene content in trees depend upon temperature and seasonal effects; Method 25A emissions from lumber drying can be modeled from a knowledge of the airflow through the kiln; A heat transfer model shows that VOCs released during hot-pressing mainly originate from the surface of the board; and Boiler ash can be used to adsorb formaldehyde from air streams.

Sujit Banerjee; Terrance Conners

2007-09-07T23:59:59.000Z

397

Reducing the solid waste stream: reuse and recycling at Lawrence Livermore National Laboratory  

Science Conference Proceedings (OSTI)

In Fiscal Year (FY) 1996 Lawrence Livermore National Laboratory (LLNL) increased its solid waste diversion by 365 percent over FY 1992 in five solid waste categories - paper, cardboard, wood, metals, and miscellaneous. (LLNL`s fiscal year is from October 1 to September 30.) LLNL reused/ recycled 6,387 tons of waste, including 340 tons of paper, 455 tons of scrap wood, 1,509 tons of metals, and 3,830 tons of asphalt and concrete (Table1). An additional 63 tons was diverted from landfills by donating excess food, selling toner cartridges for reconditioning, using rechargeable batteries, redirecting surplus equipment to other government agencies and schools, and comporting plant clippings. LLNL also successfully expanded its demonstration program to recycle and reuse construction and demolition debris as part of its facility-wide, comprehensive solid waste reduction programs.

Wilson, K. L.

1997-08-01T23:59:59.000Z

398

Homeowners energy conservation and consumption behavior: wood users and non/low wood users  

SciTech Connect

Relationships among energy expenditure, energy consumption, energy-budget share, energy managerial practices, housing, and household-membership factors for non/low wood-user and high wood-user households were examined to explain substitution of fuelwood for primary fuels. Data were from a nationwide representative sample of 1599 homeowners collected by the Department of Energy in 1982-1983 Residential Energy Conservation Survey. In three multivariate regression models, different dependent variables - energy expenditure, energy consumption, and energy budget share, were used. The same independent variables - housing factors, household energy managerial practices, and household membership factors, were used in the three models. Finally, in a fourth model, discriminant analysis with the dichotomous criterion variable of non/low or high wood users and significant variables from the multivariate regressions models were used to explain 34% of the variance. The amount of space heated, their appliance use, whether they had teenage children, and if they were single-earner households were significant explanatory variables in all four models.

Urich, J.R.

1986-01-01T23:59:59.000Z

399

Industrial Wastes as a Fuel  

E-Print Network (OSTI)

With the advent of scarce supplies and rising costs for traditional industrial fuels such as natural gas and fuel oil, a large amount of technical data has been collected and published to encourage their efficient use. This same data is readily available for coal since it was at one time a major industrial fuel and is still used extensively for electric power generation. However, combustion data for other fuels such as wood and solid materials typically generated as industrial wastes can only be found in widely scattered and more obscure sources. Therefore, this information is not always easily accessible to operating personnel at plants where these type fuels are being utilized. The resulting lack of proper information many times leads to poor fuel utilization because of less than optimum combustion efficiencies. Operational and maintenance problems may also be caused by a misunderstanding of combustion characteristics.

Richardson, G.; Hendrix, W.

1980-01-01T23:59:59.000Z

400

Ionic liquid pretreatment of poplar wood at room temperature: swelling and incorporation of nanoparticles  

DOE Green Energy (OSTI)

Lignocellulosic biomass represents a potentially sustainable source of liquid fuels and commodity chemicals. It could satisfy the energy needs for transportation and electricity generation, while contributing substantially to carbon sequestration and limiting the accumulation of greenhouse gases in the atmosphere. Potential feedstocks are abundant and include crops, agricultural wastes, forest products, grasses, and algae. Among those feedstocks, wood is mainly constituted of three components: cellulose, hemicellulose, and lignin. The conversion process of lignocellulosic biomass typically consists of three steps: (1) pretreatment; (2) hydrolysis of cellulose and hemicellulose into fermentable sugars; and (3) fermentation of the sugars into liquid fuels (ethanol) and other commodity chemicals. The pretreatment step is necessary due to the complex structure of the plant cell wall and the chemical resistance of lignin. Most current pretreatments are energy-intensive and/or polluting. So it is imperative to develop new pretreatments that are economically viable and environmentally friendly. Recently, ionic liquids have attracted considerable interest, due to their ability to dissolve biopolymers, such as cellulose, lignin, native switchgrass, and others. Ionic liquids are also considered green solvents, since they have been successfully recycled at high yields for further use with limited efficiency loss. Also, a few microbial cellulases remain active at high ionic liquid concentration. However, all studies on the dissolution of wood in ionic liquids have been conducted so far at high temperatures, typically above 90 C. Development of alternative pretreatments at room temperature is desirable to eliminate the additional energy cost. In this study, thin sections of poplar wood were swollen at room temperature by a 3 h ionic liquid (1-ethyl-3-methylimidazolium acetate or EMIMAc) pretreatment. The pretreated sample was then exposed to an aqueous suspension of nanoparticles that resulted in the sample contraction and the deposition of nanoparticles onto the surface and embedded into the cell wall. To date, both silver and gold particles ranging in size from 40-100 nm have been incorporated into wood. Penetration of gold nanoparticles of 100 nm diameter in the cell walls was best confirmed by near-infrared confocal Raman microscopy, since the deposition of gold nanoparticles induces a significant enhancement of the Raman signal from the wood in their close proximity, an enhancement attributed to the surface-enhanced Raman effect (SERS). After rinsing with water, scanning electron microscopy (SEM) and Raman images of the same areas show that most nanoparticles remained on the pretreated sample. Raman images at different depths reveal that a significant number of nanoparticles were incorporated into the wood sample, at depths up to 4 {micro}m, or 40 times the diameter of the nanoparticles. Control experiments on an untreated wood sample resulted in the deposition of nanoparticles only at the surface and most nanoparticles were removed upon rinsing. This particle incorporation process enables the development of new pretreatments, since the nanoparticles have a high surface-to-volume ratio and could be chemically functionalized. Other potential applications for the incorporated nanoparticles include isotope tracing, catalysis, imaging agents, drug-delivery systems, energy-storage devices, and chemical sensors.

Lucas, Marcel [Los Alamos National Laboratory; Macdonald, Brian A [Los Alamos National Laboratory; Wagner, Gregory L [Los Alamos National Laboratory; Joyce, Steven A [Los Alamos National Laboratory; Rector, Kirk D [Los Alamos National Laboratory

2010-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Uses and Desirable Properties of Wood in the 21st Century  

E-Print Network (OSTI)

of commercial de- velopment is use of wood pellet fuel to pro- duce heat or electric power. Wood pellets for the pellet Figure 2. Global production of paper and paperboard and wood panels by principal (continental, and production of nano-enabled materials and products are expected to increasingly shape wood use as the 21st

402

Prioritizing wood energy crop feedstock qualities for biofuel systems improvement  

SciTech Connect

Knowledge engineering or expert systems is needed in biofuel systems to adequately prioritize wood energy crop traits on which research and development should focus. Objectives at the various stages of the total biofuel process are clarifying the demands that will be placed on feedstock qualities. These objectives are forming more clearly from developments in the growing, handling, and conversion of wood under operational and regulatory circumstances. A process for systematic prioritization of wood qualities for possible improvement is presented in the content of the entire biofuel process.

Ranney, J.W.

1991-01-01T23:59:59.000Z

403

Prioritizing wood energy crop feedstock qualities for biofuel systems improvement  

SciTech Connect

Knowledge engineering or expert systems is needed in biofuel systems to adequately prioritize wood energy crop traits on which research and development should focus. Objectives at the various stages of the total biofuel process are clarifying the demands that will be placed on feedstock qualities. These objectives are forming more clearly from developments in the growing, handling, and conversion of wood under operational and regulatory circumstances. A process for systematic prioritization of wood qualities for possible improvement is presented in the content of the entire biofuel process.

Ranney, J.W.

1991-12-31T23:59:59.000Z

404

Wood-Polymer composites obtained by gamma irradiation  

Science Conference Proceedings (OSTI)

In this work we impregnate three Peruvian woods (Calycophy spruceanum Be, Aniba amazonica Meiz and Hura crepitans L) with styrene-polyester resin and methyl methacrylate. The polymerization of the system was promoted by gamma radiation and the experimental optimal condition was obtained with styrene-polyester 1:1 and 15 kGy. The obtained composites show reduced water absorption and better mechanical properties compared to the original wood. The structure of the wood-polymer composites was studied by light microscopy. Water absorption and hardness were also obtained.

Gago, J. [Instituto Peruano de Energia Nuclear, Av. Canada 1470 Lima 41 (Peru); Lopez, A.; Rodriguez, J. [Instituto Peruano de Energia Nuclear, Av. Canada 1470 Lima 41 (Peru); Facultad de Ciencias, Universidad Nacional de Ingenieria, Av. Tupac Amaru 210, Lima 25 (Peru); Santiago, J. [Instituto Peruano de Energia Nuclear, Av. Canada 1470 Lima 41 (Peru); Facultad de Quimica e Ing. Quimica, Universidad Nacional Mayor de San Marcos, Lima 1 (Peru); Acevedo, M. [Facultad de Ciencias Forestales, Universidad Nacional Agraria la Molina, Lima 12 (Peru)

2007-10-26T23:59:59.000Z

405

An economical and market analysis of Canadian wood pellets.  

Science Conference Proceedings (OSTI)

This study systematically examined the current and future wood pellet market, estimated the cost of Canadian torrefied pellets, and compared the torrefied pellets with the conventional pellets based on literature and industrial data. The results showed that the wood pellet industry has been gaining significant momentum due to the European bioenergy incentives and the rising oil and natural gas prices. With the new bioenergy incentives in USA, the future pellets market may shift to North America, and Canada can potentially become the largest pellet production centre, supported by the abundant wood residues and mountain pine beetle (MPB) infested trees.

Peng, J. [University of British Columbia, Vancouver

2010-08-01T23:59:59.000Z

406

Waste Hoist  

NLE Websites -- All DOE Office Websites (Extended Search)

45-ton Rope-Guide Friction Hoist Completely enclosed (for contamination control), the waste hoist at WIPP is a modern friction hoist with rope guides. With a 45-ton capacity, it...

407

Method for lowering the VOCS emitted during drying of wood products  

DOE Patents (OSTI)

The present invention is directed to a method for removal of VOCs from wood products prior to drying the wood products. The method of the invention includes the steps of providing a chamber having an opening for receiving wood and loading the chamber with green wood. The wood is loaded to an extent sufficient to provide a limited headspace in the chamber. The chamber is then closed and the wood is heated in the chamber for a time and at a temperature sufficient to saturate the headspace with moisture and to substantially transfer VOCs from the wood product to the moisture in the headspace.

Banerjee, Sujit (1832 Jacksons Creek Point, Marietta, GA 30068); Boerner, James Robert (154 Junedale Rd., Cincinnati, OH 45218); Su, Wei (2262 Orleans Ave., Marietta, GA 30062)

2000-01-01T23:59:59.000Z

408

Solid industrial wastes and their management in Asegra (Granada, Spain)  

Science Conference Proceedings (OSTI)

ASEGRA is an industrial area in Granada (Spain) with important waste management problems. In order to properly manage and control waste production in industry, one must know the quantity, type, and composition of industrial wastes, as well as the management practices of the companies involved. In our study, questionnaires were used to collect data regarding methods of waste management used in 170 of the 230 businesses in the area of study. The majority of these companies in ASEGRA are small or medium-size, and belong to the service sector, transport, and distribution. This was naturally a conditioning factor in both the type and management of the wastes generated. It was observed that paper and cardboard, plastic, wood, and metals were the most common types of waste, mainly generated from packaging (49% of the total volume), as well as material used in containers and for wrapping products. Serious problems were observed in the management of these wastes. In most cases they were disposed of by dumping, and very rarely did businesses resort to reuse, recycling or valorization. Smaller companies encountered greater difficulties when it came to effective waste management. The most frequent solution for the disposal of wastes in the area was dumping.

Casares, M.L. [Department of Civil Engineering, E.T.S. I.C.C.P., University of Granada (Spain), Campus Universitario de Fuentenueva s/n, 18071 Granada (Spain); Ulierte, N. [Department of Civil Engineering, E.T.S. I.C.C.P., University of Granada (Spain), Campus Universitario de Fuentenueva s/n, 18071 Granada (Spain); Mataran, A. [Area of Urban and Regional Planning, University of Granada (Spain), Laboratorio de Urbanistica y Ordenacion del Territorio, Campus Universitario de Fuentenueva s/n, 18071 Granada (Spain); Ramos, A. [Department of Civil Engineering, E.T.S. I.C.C.P., University of Granada (Spain), Campus Universitario de Fuentenueva s/n, 18071 Granada (Spain); Zamorano, M. [Department of Civil Engineering, E.T.S. I.C.C.P., University of Granada (Spain), Campus Universitario de Fuentenueva s/n, 18071 Granada (Spain)]. E-mail: zamorano@ugr.es

2005-07-01T23:59:59.000Z

409

Advanced Electrochemical Waste Forms  

Science Conference Proceedings (OSTI)

... of Fluidized Bed Steam Reforming (FBSR) with Hanford Low Activity Wastes ... Level Waste at the Defense Waste Processing Facility through Sludge Batch 7b.

410

Contribution of organic carbon to wood smoke particulate matter absorption  

NLE Websites -- All DOE Office Websites (Extended Search)

Contribution of organic carbon to wood smoke particulate matter absorption Contribution of organic carbon to wood smoke particulate matter absorption of solar radiation Title Contribution of organic carbon to wood smoke particulate matter absorption of solar radiation Publication Type Journal Article Year of Publication 2012 Authors Kirchstetter, Thomas W., and Tracy L. Thatcher Journal Atmospheric Chemistry and Physics Volume 12 Pagination 6067-6072 Abstract A spectroscopic analysis of 115 wintertime partic- ulate matter samples collected in rural California shows that wood smoke absorbs solar radiation with a strong spectral se- lectivity. This is consistent with prior work that has demon- strated that organic carbon (OC), in addition to black car- bon (BC), appreciably absorbs solar radiation in the visible and ultraviolet spectral regions. We apportion light absorp-

411

International WoodFuels LLC | Open Energy Information  

Open Energy Info (EERE)

WoodFuels LLC WoodFuels LLC Jump to: navigation, search Name International WoodFuels LLC Place Portland, Maine Zip 4101 Product Maine-based pellet producer and installer of commercial wood pellet heating systems. Coordinates 45.511795°, -122.675629° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":45.511795,"lon":-122.675629,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

412

Stanford - Woods Institute for the Environment | Open Energy Information  

Open Energy Info (EERE)

Stanford - Woods Institute for the Environment Stanford - Woods Institute for the Environment Jump to: navigation, search Logo: Stanford- Woods Institute for the Environment Name Stanford- Woods Institute for the Environment Address 473 Via Ortega Place Stanford, California Zip 94305 Region Bay Area Coordinates 37.427774°, -122.175672° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":37.427774,"lon":-122.175672,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

413

Residential Wood Heating Fuel Exemption (New York) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Wood Heating Fuel Exemption (New York) Wood Heating Fuel Exemption (New York) Residential Wood Heating Fuel Exemption (New York) < Back Eligibility Multi-Family Residential Residential Savings Category Bioenergy Maximum Rebate None Program Info State New York Program Type Sales Tax Incentive Rebate Amount 100% exemption Provider New York State Department of Taxation and Finance New York exempts retail sales of wood used for residential heating purposes from the state sales tax. The law also permits local governments (municipalities and counties) to grant an exemption from local sales taxes. If a city with a population of 1 million or more chooses to grant the local exemption, it must enact a specific resolution that appears in the state law. Local sales tax rates in New York range from 1.5% to more than 4% in

414

Qualifying Wood Stove Deduction (Idaho) | Open Energy Information  

Open Energy Info (EERE)

Share this page on Facebook icon Twitter icon Qualifying Wood Stove Deduction (Idaho) This is the approved revision of this page, as well as being the most recent. Jump...

415

John H. Wood Gary R. Long David F. Morehouse Energy ...  

U.S. Energy Information Administration (EIA)

Long-Term World Oil Supply Scenarios The Future Is Neither as Bleak or Rosy as Some Assert John H. Wood Gary R. Long David F. Morehouse Energy Information Administration

416

Test evaluation of a laminated wood wind turbine blade concept  

SciTech Connect

Because of the high stiffness and fatigue strength of wood (as compared to density) along with the low cost manufacturing techniques available, a laminated wood wind turbine blade application has been studied. This report presents the results of the testing performed on elements of the wood blade-to-hub transition section which uses steel studs cast into a laminated wood spar with a filled epoxy. Individual stud samples were tested for both ultimate load carrying capability and fatigue strength. A one-time pull-out load of 78,000 lb was achieved for a 15 in. long stud with a diameter of 1 in. Tension-tension fatigue indicated that peak loads on the order of 40% of ultimate could be maintained as an endurance limit (mean load = 20,000 lb, cyclic load = +-15,000 lb). Following the individual stud testing, a full-scale inboard blade section (20 ft in length) was tested.

Faddoul, J.R.

1981-05-01T23:59:59.000Z

417

DOE Joint Genome Institute: Rot's Unique Wood Degrading Machinery...  

NLE Websites -- All DOE Office Websites (Extended Search)

February 5, 2009 Rot's Unique Wood Degrading Machinery to be Harnessed for Better Biofuels Production WALNUT CREEK, CA-An international team led by scientists from the U.S....

418

Wood Products Marketing And Value-Added Opportunities  

E-Print Network (OSTI)

Opportunities -MDF- Market Opportunities -MDF- The first MDF plant started up four years ago and now there are 3 the substrate of choice for exotic wood veneer layup. Pressing veneer on MDF will give the most defect

419

Signatures of surface bundles and Milnor Wood inequalities  

E-Print Network (OSTI)

Let E be a surface bundle over a surface. We use a variant of the Milnor Wood inequality to show that $|3\\sigma(E)|\\leq \\chi(E)$.

Hamenstaedt, Ursula

2012-01-01T23:59:59.000Z

420

Municipal solid waste management in Beijing City  

Science Conference Proceedings (OSTI)

This paper presents an overview of municipal solid waste (MSW) management in Beijing City. Beijing, the capital of China, has a land area of approximately 1368.32 km{sup 2} with an urban population of about 13.33 million in 2006. Over the past three decades, MSW generation in Beijing City has increased tremendously from 1.04 million tons in 1978 to 4.134 million tons in 2006. The average generation rate of MSW in 2006 was 0.85 kg/capita/day. Food waste comprised 63.39%, followed by paper (11.07%), plastics (12.7%) and dust (5.78%). While all other wastes including tiles, textiles, glass, metals and wood accounted for less than 3%. Currently, 90% of MSW generated in Beijing is landfilled, 8% is incinerated and 2% is composted. Source separation collection, as a waste reduction method, has been carried out in a total of 2255 demonstration residential and commercial areas (covering about 4.7 million people) up to the end of 2007. Demonstration districts should be promoted over a wider range instead of demonstration communities. The capacity of transfer stations and treatment plants is an urgent problem as these sites are seriously overloaded. These problems should first be solved by constructing more sites and converting to new treatment technologies. Improvements in legislation, public education and the management of waste pickers are problematic issues which need to be addressed.

Li Zhenshan [Department of Environmental Engineering, Peking University, Key Laboratory of Water and Sediment Sciences, Ministry of Education, No. 5, Yi Heyuan Road, Haidian District, Beijing 100871 (China); Key Laboratory for Environmental and Urban Sciences, Shenzhen Graduate School, Peking University, Shenzhen 518055 (China)], E-mail: lizhenshan@pku.edu.cn; Yang Lei [Department of Environmental Engineering, Peking University, Key Laboratory of Water and Sediment Sciences, Ministry of Education, No. 5, Yi Heyuan Road, Haidian District, Beijing 100871 (China); Qu XiaoYan [Key Laboratory for Environmental and Urban Sciences, Shenzhen Graduate School, Peking University, Shenzhen 518055 (China); Sui Yumei [Department of Environmental Engineering, Peking University, Key Laboratory of Water and Sediment Sciences, Ministry of Education, No. 5, Yi Heyuan Road, Haidian District, Beijing 100871 (China)

2009-09-15T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Methanol synthesis gas from catalytic steam reforming of wood  

DOE Green Energy (OSTI)

Laboratory studies were successful in developing catalyst systems and operating conditions for generation of a methanol synthesis gas, a mixture of hydrogen, carbon monoxide and carbon dioxide. Some methane remained in the gas mixture. Wood was reacted with steam at a steam-to-wood weight ratio of about 0.9 and a temperature of 750/sup 0/C (1380/sup 0/F) in the presence of several catalysts. Results are presented for two different catalyst systems.

Mudge, L.K.; Mitchell, D.H.; Robertus, R.J.; Weber, S.L.; Sealock, L.J. Jr.

1981-01-01T23:59:59.000Z

422

The adoption of e-commerce for wood enterprises  

Science Conference Proceedings (OSTI)

Lately, the internet has become a major means in electronic commerce (e-commerce), as it offers various advantages and benefits. In Greece, there are many Small- and Medium-sized Enterprises (SMEs) in the context of the timber ... Keywords: Greece, ICT adoption, PROMETHEE II method, SMEs, e-commerce, electronic commerce, multi-criteria analysis, small and medium-sized enterprises, timber trade, web content, website ranking, wood processing, wood products

Z. S. Andreopoulou; T. Koutroumanidis; B. Manos

2009-04-01T23:59:59.000Z

423

Municipal solid waste combustion: Fuel testing and characterization  

DOE Green Energy (OSTI)

The objective of this study is to screen and characterize potential biomass fuels from waste streams. This will be accomplished by determining the types of pollutants produced while burning selected municipal waste, i.e., commercial mixed waste paper residential (curbside) mixed waste paper, and refuse derived fuel. These materials will be fired alone and in combination with wood, equal parts by weight. The data from these experiments could be utilized to size pollution control equipment required to meet emission standards. This document provides detailed descriptions of the testing methods and evaluation procedures used in the combustion testing and characterization project. The fuel samples will be examined thoroughly from the raw form to the exhaust emissions produced during the combustion test of a densified sample.

Bushnell, D.J.; Canova, J.H.; Dadkhah-Nikoo, A.

1990-10-01T23:59:59.000Z

424

Material and energy recovery in integrated waste management systems: Project overview and main results  

Science Conference Proceedings (OSTI)

Highlights: > The source separation level (SSL) of waste management system does not qualify adequately the system. > Separately collecting organic waste gives less advantages than packaging materials. > Recycling packaging materials (metals, glass, plastics, paper) is always attractive. > Composting and anaerobic digestion of organic waste gives questionable outcomes. > The critical threshold of optimal recycling seems to be a SSL of 50%. - Abstract: This paper describes the context, the basic assumptions and the main findings of a joint research project aimed at identifying the optimal breakdown between material recovery and energy recovery from municipal solid waste (MSW) in the framework of integrated waste management systems (IWMS). The project was carried out from 2007 to 2009 by five research groups at Politecnico di Milano, the Universities of Bologna and Trento, and the Bocconi University (Milan), with funding from the Italian Ministry of Education, University and Research (MIUR). Since the optimization of IWMSs by analytical methods is practically impossible, the search for the most attractive strategy was carried out by comparing a number of relevant recovery paths from the point of view of mass and energy flows, technological features, environmental impact and economics. The main focus has been on mature processes applicable to MSW in Italy and Europe. Results show that, contrary to a rather widespread opinion, increasing the source separation level (SSL) has a very marginal effects on energy efficiency. What does generate very significant variations in energy efficiency is scale, i.e. the size of the waste-to-energy (WTE) plant. The mere value of SSL is inadequate to qualify the recovery system. The energy and environmental outcome of recovery depends not only on 'how much' source separation is carried out, but rather on 'how' a given SSL is reached.

Consonni, Stefano, E-mail: stefano.consonni@polimi.it [Department of Energy, Politecnico di Milano, Via Lambruschini 4, 20156 Milan (Italy); Giugliano, Michele [DIIAR, Environmental Section, Politecnico di Milano, P.za L. Da Vinci 32, 20133 Milan (Italy); Massarutto, Antonio [Dse, Universita degli Studi di Udine and IEFE, Via Tomadini 30/a, 33100 Udine (Italy); Ragazzi, Marco [Department of Civil and Environmental Engineering, University of Trento, Via Mesiano 77, 38123 Trento (Italy); Saccani, Cesare [DIEM, University of Bologna, Viale Risorgimento 2, 40136 Bologna (Italy)

2011-09-15T23:59:59.000Z

425

U.S. Energy Information Administration - EIA - Independent ...  

U.S. Energy Information Administration (EIA)

To meet the renewable electricity standard, PREPA is focusing on wind, solar, and waste-to-energy projects.

426

Assessing recycling versus incineration of key materials in municipal waste: The importance of efficient energy recovery and transport distances  

SciTech Connect

Highlights: Black-Right-Pointing-Pointer We model the environmental impact of recycling and incineration of household waste. Black-Right-Pointing-Pointer Recycling of paper, glass, steel and aluminium is better than incineration. Black-Right-Pointing-Pointer Recycling and incineration of cardboard and plastic can be equally good alternatives. Black-Right-Pointing-Pointer Recyclables can be transported long distances and still have environmental benefits. Black-Right-Pointing-Pointer Paper has a higher environmental benefit than recyclables found in smaller amounts. - Abstract: Recycling of materials from municipal solid waste is commonly considered to be superior to any other waste treatment alternative. For the material fractions with a significant energy content this might not be the case if the treatment alternative is a waste-to-energy plant with high energy recovery rates. The environmental impacts from recycling and from incineration of six material fractions in household waste have been compared through life cycle assessment assuming high-performance technologies for material recycling as well as for waste incineration. The results showed that there are environmental benefits when recycling paper, glass, steel and aluminium instead of incinerating it. For cardboard and plastic the results were more unclear, depending on the level of energy recovery at the incineration plant, the system boundaries chosen and which impact category was in focus. Further, the environmental impact potentials from collection, pre-treatment and transport was compared to the environmental benefit from recycling and this showed that with the right means of transport, recyclables can in most cases be transported long distances. However, the results also showed that recycling of some of the material fractions can only contribute marginally in improving the overall waste management system taking into consideration their limited content in average Danish household waste.

Merrild, Hanna [Department of Environmental Engineering, Technical University of Denmark, Miljoevej, Building 113, DK-2800 Kongens Lyngby (Denmark); Larsen, Anna W., E-mail: awla@env.dtu.dk [Department of Environmental Engineering, Technical University of Denmark, Miljoevej, Building 113, DK-2800 Kongens Lyngby (Denmark); Christensen, Thomas H. [Department of Environmental Engineering, Technical University of Denmark, Miljoevej, Building 113, DK-2800 Kongens Lyngby (Denmark)

2012-05-15T23:59:59.000Z

427

Contesting Governance in the Global Marketplace: A Sociological Assessment of British Efforts to Build New Markets for NGO-Certified Sustainable Wood Products  

E-Print Network (OSTI)

Towards Environmentally Sound Wood Products In the Britishof the Earth. 1995. The Good Wood Guide. Friends of theRamachandra. 1990. The Unquiet Woods: Ecological Change and

McNichol, Jason

2000-01-01T23:59:59.000Z

428

Extracellular oxidative metabolism of wood decay fungi  

DOE Green Energy (OSTI)

Substantial progress has been made toward understanding the fundamental physiology and genetics of wood decay fungi, microbes that are capable of degrading all major components of plant cell walls. Efficient utilization of lignocellulosic biomass has been hampered in part by limitations in our understanding of enzymatic mechanisms of plant cell wall degradation. This is particularly true of woody substrates where accessibility and high lignin content substantially complicate enzymatic 'deconstruction'. The interdisciplinary research has illuminated enzymatic mechanisms essential for the conversion of lignocellulosics to simple carbohydrates and other small molecular weight products. Progress was in large part dependent on substantial collaborations with the Department of Energy's Joint Genome Institute (JGI) in Walnut Creek and Los Alamos, as well as the Catholic University, Santiago, Chile, the Royal Institute of Technology, Stockholm, the University of Minnesota, St. Paul, and colleagues at the University of Wisconsin and the Forest Products Laboratory. Early accomplishments focused on the development of experimental tools (2, 7, 22, 24-26, 32) and characterization of individual genes and enzymes (1, 3-5, 8, 9, 11, 14, 15, 17, 18, 23, 27, 33). In 2004, the genome of the most intensively studied lignin-degrading fungus, Phanerochaete chrysosporium, was published (21). This milestone lead to additional progress on this important model system (6, 10, 12, 13, 16, 28-31) and was further complemented by genome analysis of other important cellulose-degrading fungi (19, 20). These accomplishments have been highly cited and have paved the way for whole new research areas.

Daniel Cullen

2010-04-21T23:59:59.000Z

429

Understanding Cement Waste Forms  

Science Conference Proceedings (OSTI)

Oct 29, 2009 ... Ongoing nuclear operations, decontamination and decommissioning, salt waste disposal, and closure of liquid waste tanks result in...

430

Waste Minimization Contents  

Science Conference Proceedings (OSTI)

About the 1996 International Symposium on Extraction and Processing for the Treatment and Minimization of Wastes: Waste Minimization Contents...

431

Moisture Distribution and Flow During Drying of Wood and Fiber  

DOE Green Energy (OSTI)

New understanding, theories, and techniques for moisture flow and distribution were developed in this research on wood and wood fiber. Improved understanding of the mechanisms of flake drying has been provided. Observations of flake drying and drying rate curves revealed that rate of moisture loss consisted of two falling rate periods and no constant rate drying period was observed. Convective heat transfer controls the first period, and bound water diffusion controls the second period. Influence of lower drying temperatures on bending properties of wood flakes was investigated. Drying temperature was found to have a significant influence on bending stiffness and strength. A worksheet for calculation of the energy required to dry a single strandboard flake was developed but has not been tested in an industrial setting yet. A more complete understanding of anisotropic transverse shrinkage of wood is proposed based on test results and statistical analysis. A simplified mod el of a wood cell's cross-section was drawn for calculating differential transverse shrinkage. The model utilizes cell wall thickness and microfibrillar packing density and orientation. In spite of some phenomena of cell wall structure not yet understood completely, the results might explain anisotropic transverse shrinkage to a major extent. Boundary layer theory was found useful for evaluating external moisture resistance during drying. Simulated moisture gradients were quire comparable to the actual gradients in dried wood. A mathematical procedure for determining diffusion and surface emission coefficients was also developed. Thermal conductivity models of wood derived from its anatomical structure were created and tested against experimental values. Model estimations provide insights into changes in heat transfer parameters during drying. Two new techniques for measuring moisture gradients created in wood during drying were developed. A new technique that utilizes optical properties of cobalt chloride was developed for nondestructive determination of surface moisture content. Fundamental new understanding of drying characteristics in wood and fiber has been provided that can be used by researchers to improve drying of wood and fiber. The three techniques for measuring moisture content and gradients provided in this study are efficient, practical, and economical - easy to apply by industry and researchers. An energy consumption worksheet is provided as a first step toward reducing energy consumed during drying of lumber and strandboard flakes. However, it will need additional verification and testing.

Zink-Sharp, Audrey; Hanna, Robert B.

2001-12-28T23:59:59.000Z

432

CX-009166: Categorical Exclusion Determination | Department of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Determination Bioelectrochemical Integration of Waste Heat Recovery, Waste-to-Energy Conversion, and Waste-to-Chemical Conversion with Industrial Gas and Chemical...

433

Guidebook for Using the Tool BEST Cement: Benchmarking and Energy Savings Tool for the Cement Industry  

E-Print Network (OSTI)

This practice wastes substantial energy and should never beHeat recovery from waste-to-energy boilers increases theway to recover energy from waste. The carbon dioxide

Galitsky, Christina

2009-01-01T23:59:59.000Z

434

Attracting "Green Industry": An Economic Development Approach for the City of Los Angeles  

E-Print Network (OSTI)

air emissions and waste and to energy conservation measures.emissions and waste, and take various energy conservationand scooters. Biomass / Waste-to-Energy Power: Processing

Laurie Kaye

2006-01-01T23:59:59.000Z

435

PROCEEDINGS OF 1976 SUMMER WORKSHOP ON AN ENERGY EXTENSION SERVICE  

E-Print Network (OSTI)

PROGRAM THRUSTS: 1. WASTE ENERGY REDUCTION (REDUCE ENERGYtypes that consume and waste energy during the long periodscycle energy systems, waste-to-energy conversion systems,

Authors, Various

2010-01-01T23:59:59.000Z

436

A distributed approach to accounting for carbon in wood products  

SciTech Connect

With an evolving political environment of commitments to limit emissions of greenhouse gases, and of markets to trade in emissions permits, there is growing scientific, political, and economic need to accurately evaluate carbon (C) stocks and flows especially those related to human activities. One component of the global carbon cycle that has been contentious is the stock of carbon that is physically held in harvested wood products. The carbon stored in wood products has been sometimes overlooked, but the amount of carbon contained in wood products is not trivial, it is increasing with time, and it is significant to some Parties. This paper is concerned with accurate treatment of harvested wood products in inventories of CO2 emissions to the atmosphere. The methodologies outlined demonstrate a flexible way to expand current methods beyond the assumption of a simple, first-order decay to include the use of more accurate and detailed data while retaining the simplicity of simple formulas. The paper demonstrates that a more accurate representation of decay time can have significant economic implications in a system where emissions are taxed or emissions permits are traded. The method can be easily applied using only data on annual production of wood products and two parameters to characterize their expected lifetime. These methods are not specific to wood products but can be applied to long-lived, carbon-containing products from sources other than wood, e.g. long-lived petrochemical products. A single unifying approach that is both simple and flexible has the potential to be both more accurate in its results, more efficient in its implementation, and economically important to some Parties.

Marland, Eric [Appalachian State University; Stellar, Kirk [Appalachian State University; Marland, Gregg [ORNL

2010-01-01T23:59:59.000Z

437

Decision-maker's guide to wood fuel for small industrial energy users. Final report. [Includes glossary  

DOE Green Energy (OSTI)

The technology and economics of various wood energy systems available to the small industrial and commercial energy user are considered. This book is designed to help a plant manager, engineer, or others in a decision-making role to become more familiar with wood fuel systems and make informed decisions about switching to wood as a fuel. The following subjects are discussed: wood combustion, pelletized wood, fuel storage, fuel handling and preparation, combustion equipment, retrofitting fossil-fueled boilers, cogeneration, pollution abatement, and economic considerations of wood fuel use. (MHR)

Levi, M. P.; O'Grady, M. J.

1980-02-01T23:59:59.000Z

438

The evolution and ecology of interspecific territoriality: Studies of Anolis lizards and North American wood-warblers  

E-Print Network (OSTI)

and E. Bermingham. 2002. What is a wood-warbler? Molecularmultilocus phylogeny for the wood-warblers and a revisedplayback experiments with wood warblers. Ecology 82:207-218.

Losin, Neil

2012-01-01T23:59:59.000Z

439

ENERGY BUDGETS AND MASONRY HOUSES: A PRELIMINARY ANALYSIS OF THE COMPARATIVE ENERGY PERFORMANCE OF MASONRY AND WOOD-FRAME HOUSES  

E-Print Network (OSTI)

ENERGY PERFORMANCE OF MASONRY AND WOOD-FRAME HOUSES David B.PERFORMANCE OF MASONRY AND WOOD-FRAME HOUSES David B. Goldsfor those studies used wood- frame construction, The energy

Goldstein, David B.

2012-01-01T23:59:59.000Z

440

Understanding wood-pool dynamics using long-term monitoring data from the Gualala River Watershed: What can we learn?  

E-Print Network (OSTI)

and D. R. Montgomery. 2003. Wood in river rehabilitation andPatterns and process of wood debris accumulation in theand S. V. Gregory. 2002. Large wood and fluvial processes.

Church, Tamara

2012-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Linda Sargent Wood. A More Perfect Union: Holistic Worldviews and the Transformation of American Culture after World War II.  

E-Print Network (OSTI)

23 No. 1 Linda Sargent Wood. A More Perfect Union: HolisticCold War era, Linda Sargent Wood argues that the equallyWorld War II period. For Wood, this cultural perspective

Promnitz, Sarah

2012-01-01T23:59:59.000Z

442

Comminution process to produce precision wood particles of uniform size and shape with disrupted grain structure from wood chips  

DOE Patents (OSTI)

A process of comminution of wood chips (C) having a grain direction to produce a mixture of wood particles (P), wherein the wood chips are characterized by an average length dimension (L.sub.C) as measured substantially parallel to the grain, an average width dimension (W.sub.C) as measured normal to L.sub.C and aligned cross grain, and an average height dimension (H.sub.C) as measured normal to W.sub.C and L.sub.C, and wherein the comminution process comprises the step of feeding the wood chips in a direction of travel substantially randomly to the grain direction through a counter rotating pair of intermeshing arrays of cutting discs (D) arrayed axially perpendicular to the direction of wood chip travel, wherein the cutting discs have a uniform thickness (T.sub.D), and wherein at least one of L.sub.C, W.sub.C, and H.sub.C is greater than T.sub.D.

Dooley, James H; Lanning, David N

2013-08-13T23:59:59.000Z

443

Water Sampling At Heber Area (Wood, 2002) | Open Energy Information  

Open Energy Info (EERE)

Heber Area (Wood, 2002) Heber Area (Wood, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Water Sampling At Heber Area (Wood, 2002) Exploration Activity Details Location Heber Area Exploration Technique Water Sampling Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Geothermal fluids from hot springs and wells have been sampled from a number of locations, including: 1) the North Island of New Zealand (three sets of samples from three different years) and the South Island of New Zealand (1 set of samples); 2) the Cascades of Oregon; 3) the Harney, Alvord Desert and Owyhee geothermal areas of Oregon; 4) the Dixie Valley and Beowawe fields in Nevada; 5) Palinpiiion, the Philippines; 6) the Salton Sea and Heber geothermal fields of southern California; and 7) the

444

Hancock-Wood Electric Coop Inc | Open Energy Information  

Open Energy Info (EERE)

Hancock-Wood Electric Coop Inc Hancock-Wood Electric Coop Inc Jump to: navigation, search Name Hancock-Wood Electric Coop Inc Place Ohio Utility Id 8034 Utility Location Yes Ownership C NERC Location RFC NERC RFC Yes RTO PJM Yes Activity Distribution Yes References EIA Form EIA-861 Final Data File for 2010 - File1_a[1] LinkedIn Connections CrunchBase Profile No CrunchBase profile. Create one now! This article is a stub. You can help OpenEI by expanding it. Utility Rate Schedules Grid-background.png Farm Service-R-107 Commercial Farm Sevice R-207 Commercial Farm Sevice R-207(Transformer Capacity in Excess of 25kVA) Commercial LPS Rate 12 (Mainland) Industrial LPS Rate 12KI (Kelleys Island) Industrial NR Rate GS-8KI (Kelleys Island) Commercial NR Rate GS-8M (Mainland) Commercial NR Rate GS-9KI - Kelleys Island Over 25 kW Commercial

445

Water Sampling At International Geothermal Area, New Zealand (Wood, 2002) |  

Open Energy Info (EERE)

International Geothermal Area, New Zealand (Wood, 2002) International Geothermal Area, New Zealand (Wood, 2002) Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Activity: Water Sampling At International Geothermal Area New Zealand (Wood, 2002) Exploration Activity Details Location International Geothermal Area New Zealand Exploration Technique Water Sampling Activity Date Usefulness could be useful with more improvements DOE-funding Unknown Notes Geothermal fluids from hot springs and wells have been sampled from a number of locations, including: 1) the North Island of New Zealand (three sets of samples from three different years) and the South Island of New Zealand (1 set of samples); 2) the Cascades of Oregon; 3) the Harney, Alvord Desert and Owyhee geothermal areas of Oregon; 4) the Dixie Valley

446

Hogged Wood Fuel Supply and Price Analysis : Final Report.  

SciTech Connect

This study discusses the factors that determine the supply and demand for hogged wood in the Pacific Northwest, with particular emphasis on the role of the regional pulp and paper industry and lumber industry. Because hogged wood is often a substitute for conventional fuels, the consumption and price of natural gas, electricity, fuel oil and coal are also addressed. A detailed and comprehensive examination of the indicies relating to the hogged wood market is provided, including analysis and graphing of all time series variables. A spreadsheet- based forecasting model is developed and presented with an emphasis on explaining the process used to arrive at the final model. 42 refs., 46 figs., 14 tabs. (MHB)

Biederman, Richard T.; Blazek, Christopher F.

1991-05-01T23:59:59.000Z

447

Wood for energy and rural development: the Philippine experience  

Science Conference Proceedings (OSTI)

The Philippine wood energy programme (dendro-thermal system) was originally developed as a source of energy independent of imported oil, and at a lower cost than oil. It has social benefits: new jobs, land distribution, rural income increment, and reforestation by tree farmers. Tree farming, its administration and organization of farmer institutions are essential to the programme, as are the development of farming techniques to produce energy, trees (growth of ipil-ipil), and an improved tree growth rate. An analysis of the economics of wood energy led to the conclusion that raw wood fuel can be cheaper than oil. In estimated costs of electricity, the dendro-thermal plants can produce power at competitive rates. 36 references.

Denton, F.H.

1983-01-01T23:59:59.000Z

448

Waste Hoist  

NLE Websites -- All DOE Office Websites (Extended Search)

Primary Hoist: 45-ton Rope-Guide Friction Hoist Largest friction hoist in the world when it was built in 1985 Completely enclosed (for contamination control), the waste hoist at WIPP is a modern friction hoist with rope guides (uses a balanced counterweight and tail ropes). With a 45-ton capacity, it was the largest friction hoist in the world when it was built in 1986. Hoist deck footprint: 2.87m wide x 4.67m long Hoist deck height: 2.87m wide x 7.46m high Access height to the waste hoist deck is limited by a high-bay door at 4.14m high Nominal configuration is 2-cage (over/under), with bottom (equipment) cage interior height of 4.52m The photo, at left, shows the 4.14m high-bay doors at the top collar of the waste hoist shaft. The perpendicular cross section of the opening is 3.5m x 4.14m, but the bottom cage cross section is 2.87m x 4.5m (and 4.67m into the plane of the photo).

449

Clean-Burning Wood Stove Grant Program (Maryland) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Clean-Burning Wood Stove Grant Program (Maryland) Clean-Burning Wood Stove Grant Program (Maryland) Clean-Burning Wood Stove Grant Program (Maryland) < Back Eligibility Residential Savings Category Bioenergy Program Info Start Date 09/07/2012 State Maryland Program Type State Rebate Program Rebate Amount Stick Burning Stove: $500 Pellet Burning Stove: $700 The Maryland Energy Administration (MEA) now offers the Clean Burning Wood Stove Grant program as part of its Residential Clean Energy Grant Program. The Clean Burning Wood Stove Grant program offers a flat grant award of $500 for stick burning wood stoves and $700 for pellet burning wood stoves that meet program eligibility requirements. Basic requirements for grant funding include: *The property must serve as primary residence *Clean burning wood stove must replace existing electric or non-natural gas

450

Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program Residential Bulk-Fed Wood-Pellet Central Boilers and Furnace Rebate Program Eligibility Multi-Family Residential...

451

Name: Qinglin Wu Title: Roy O Martin Sr. Professor, Composites and Engineered Wood Products  

E-Print Network (OSTI)

Department: School of Renewable Natural Resources Mailing Address: 107 Renewable-Natural-Resources Building Louisiana Forest Products Development Center (LFPDC) School of Renewable Natural Resources Louisiana State. China. RESEARCH INTERESTS Wood and natural fiber polymer composites, engineered wood products, composite

452

Assessment of existing feuds data base for identification of potential industrial wood users in North Carolina  

DOE Green Energy (OSTI)

The North Carolina Wood Assistance Team's evaluation of the Ultrasystems' computerized methodology for identifying high potential wood conversion facilities is presented. The analysis, methodology, and data are found to be inadequate for the intended use.

Gustashaw, D.H.

1981-03-01T23:59:59.000Z

453

EA-1850: Flambeau River BioFuels, Inc. Proposed Wood Biomass...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

850: Flambeau River BioFuels, Inc. Proposed Wood Biomass-to-Liquid Fuel Biorefinery, Park Falls, Wisconsin EA-1850: Flambeau River BioFuels, Inc. Proposed Wood Biomass-to-Liquid...

454

EA-1811: NewPage Corporation Wood Biomass to Liquid Fuel, Wisconsin...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1: NewPage Corporation Wood Biomass to Liquid Fuel, Wisconsin Rapids, Wisconsin EA-1811: NewPage Corporation Wood Biomass to Liquid Fuel, Wisconsin Rapids, Wisconsin Summary This...

455

Medical School Biomedical Waste  

E-Print Network (OSTI)

Medical School Biomedical Waste Labware, gloves, pipets, pipet tips Stock cultures, bacterial with or without needles, razor blades, scalpel blades) Key: Pathological waste BL1 & BL2 waste (low risk ­ LR) BL2 waste (moderate risk - MR)/BL3 waste Blood Blood Autoclave Needle box Metal Cart Must either bleach

Cooley, Lynn

456

Waste Sorting Activity Introduction  

E-Print Network (OSTI)

Waste Sorting Activity Introduction: This waste sorting game was originally designed to be one have completed the waste sorting activity quickly, no team was able to complete the waste sorting task who were unfamiliar with Dalhousie's waste management system. Goals: The primary goal of the activity

Beaumont, Christopher

457

University of Waste Procedures  

E-Print Network (OSTI)

University of Maryland Hazardous And Regulated Waste Procedures Manual Revised July 2001 #12;Review II. HAZARDOUS WASTE MANAGEMENT III. BIOLOGICAL, PATHOLOGICAL AND MEDICAL WASTE (BPMW) MANAGEMENT IV. LOW-LEVEL RADIOACTIVE WASTE (LLRW) MANAGEMENT V. EMERGENCY PROCEDURES VI. WASTE MINIMIZATION VII

Rubloff, Gary W.

458

Field Guide: Visual Inspection of Wood Structures (Optimized for Electronic Viewing)  

Science Conference Proceedings (OSTI)

The Field Guide: Visual Inspection of Wood Structures is a catalog of photographs illustrating various conditions and factors that commonly affect transmission line wood structures, along with their likely causes, a Maintenance Priority Rating, and suggested actions to be taken by utility personnel. Poles, cross-arms, cross-arm braces, X-braces, brackets, anchor rods, guy wires, and direct imbedded foundations are covered. Other sections include types of wood structures, the anatomy of wood ...

2011-11-09T23:59:59.000Z

459

Fate of Cu, Cr, and As during combustion of impregnated wood with and without peat additive  

SciTech Connect

The EU Directive on incineration of waste regulates the harmful emissions of particles and twelve toxic elements, including copper, chromium, and arsenic. Using a 15 kW pellets-fueled grate burner, experiments were performed to determine the fate of copper, chromium, and arsenic during combustion of chromate copper arsenate (CCA) preservative wood. The fate and speciation of copper, chromium, and arsenic were determined from analysis of the flue gas particles and the bottom ash using SEM-EDS, XRD, XPS, and ICP-AES. Chemical equilibrium model calculations were performed to interpret the experimental findings. The results revealed that about 5% copper, 15% chromium, and 60% arsenic were volatilized during combustion of pure CCA-wood, which is lower than predicted volatilization from the individual arsenic, chromium, and copper oxides. This is explained by the formation of more stable refractory complex oxide phases for which the stability trends and patterns are presented. When co-combusted with peat, an additional stabilization of these phases was obtained and thus a small but noteworthy decrease in volatilization of all three elements was observed. The major identified phases for all fuels were CuCrO{sub 2}(s), (Fe,Mg,Cu)(Cr,Fe,Al)O{sub 4}(s), Cr{sub 2}O{sub 3}(s), and Ca{sub 3}(AsO{sub 4}){sub 2}(s). Arsenic was also identified in the fine particles as KH{sub 2}AsO{sub 4}(s) and As{sub 2}O{sub 3}). A strong indication of hexavalent chromium in the form of K{sub 2}CrO{sub 4} or as a solid solution between K{sub 3}Na(CrO{sub 4}){sub 2} and K{sub 3}Na(SO{sub 4}){sub 2} was found in the fine particles. Good qualitative agreement was observed between experimental data and chemical equilibrium model calculations. 38 refs., 6 figs., 2 tabs.

Karin Lundholm; Dan Bostroem; Anders Nordin; Andrei Shchukarev [Umeaa University, Umeaa (Sweden). Energy Technology and Thermal Process Chemistry

2007-09-15T23:59:59.000Z

460

Modern Wood Energy Systems and Markets 16-17 September 2008, Timisoara, Romania  

E-Print Network (OSTI)

Modern Wood Energy Systems and Markets 16-17 September 2008, Timisoara, Romania International Wood Energy Market Developments Ed Pepke Forest Products Marketing Specialist UNECE/FAO Timber Section, Geneva #12;Modern Wood Energy Systems and Markets 16-17 September 2008, Timisoara, Romania Subjects I

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Development of Wood Chips and Pellets market in Slovakia Jozef Viglasky, SK-BIOM, Slovakia  

E-Print Network (OSTI)

is supported by the Danish Government. One of the main barriers for extension of wood pellet production is lack1 Development of Wood Chips and Pellets market in Slovakia Jozef Viglasky, SK-BIOM, Slovakia-combustion of wood residues in existing coal fired power systems. #12;3 · Implementation of low cost anaerobic

462

Hydrologic and Water-Quality Conditions During Restoration of the Wood River Wetland,  

E-Print Network (OSTI)

.S. Geological Survey #12;Front Cover: Aerial view of the lower Wood River Valley showing the Wood River Wetland.S. Geological Survey, January 2003. #12;Hydrologic and Water-Quality Conditions During Restoration of the Wood­5004 U.S. Department of the Interior U.S. Geological Survey #12;U.S. Department of the Interior KEN

463

Discrimination of bark from wood chips through texture analysis by image processing  

Science Conference Proceedings (OSTI)

Utilization of wood chips for bioenergy requires classification and segregation of the constituents of the chipped mass to help optimize energy conversion. Wood chips obtained from processes such as forest thinning can contain a considerable amount of ... Keywords: Bark, Biomass, Image processing, Texture analysis, Wood chip

James R. Wooten; S. D. Filip To; C. Igathinathane; L. O. Pordesimo

2011-10-01T23:59:59.000Z

464

EFFECTS OF SAMPLE SIZE ON CHARACTERIZATION OF WOOD-PARTICLE LENGTH DISTRIBUTION  

E-Print Network (OSTI)

EFFECTS OF SAMPLE SIZE ON CHARACTERIZATION OF WOOD-PARTICLE LENGTH DISTRIBUTION Quang V. Cao of sample size on fitting length distribution of wood particles used for manufacturing wood-based composites moments and the ability of the sample distributions to characterize the population represented

465

Radioactive Waste Management (Minnesota)  

Energy.gov (U.S. Department of Energy (DOE))

This section regulates the transportation and disposal of high-level radioactive waste in Minnesota, and establishes a Nuclear Waste Council to monitor the federal high-level radioactive waste...

466

Waste Management Program  

NLE Websites -- All DOE Office Websites (Extended Search)

Waste Management Facility ISO 14001 Registered A wide range of wastes are generated during the normal course of business at BNL. These waste streams are common to many businesses...

467

Woods Hole Research Center Wind Turbine | Open Energy Information  

Open Energy Info (EERE)

Hole Research Center Wind Turbine Hole Research Center Wind Turbine Jump to: navigation, search Name Woods Hole Research Center Wind Turbine Facility Woods Hole Research Center Wind Turbine Sector Wind energy Facility Type Small Scale Wind Facility Status In Service Owner Woods Hole Research Center Developer Sustainable Energy Developments Energy Purchaser Woods Hole Research Center Location Falmouth MA Coordinates 41.548637°, -70.64326° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":41.548637,"lon":-70.64326,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

468

Production of chemical feedstock by the methanolysis of wood  

DOE Patents (OSTI)

A process is discussed for the production of ethylene, benzene and carbon monoxide from particulated biomass such as wood by reaction with methane at a temperature of from 700/sup 0/C to 1200/sup 0/C, at a pressure of from 20 psi to 100 psi for a period of from 0.2 to 10 seconds.

Steinberg, M.; Fallon, P.

1983-06-01T23:59:59.000Z

469

Wood Products Marketing And Value-Added Opportunities  

E-Print Network (OSTI)

Point, NC, 27261, USA Tel.: (336) 841 8535 Fax.: (336) 841 5435 151 Randall St. Oakville, ON Canada, L6J SituationThe Situation As global populations continue to grow, the demand for wood products will increase in: Cultures Technology Infrastructure #12;Demand: Overall ClimateDemand: Overal

470

Temperature Measurements in Full-Scale Wood Stud Shear Walls  

E-Print Network (OSTI)

This report presents the results of 10 full-scale fire resistance tests conducted at the National Fire Laboratory on load-bearing gypsum board protected, wood stud shear wall assemblies with and without resilient channels on the fire-exposed side. The two assembly arrangements studied were: symmetrical installation 1x1 (one layer of gypsum board on each of the exposed and unexposed sides) and asymmetrical installation of the shear membrane (one layer of gypsum board on both the exposed and unexposed sides and a shear wall membrane as a base layer alternating between the exposed (2x1) and unexposed sides (1x2)) on a wood stud frame. The gypsum board was 12.7 mm thick Type X. The insulations used were glass and rock fibres. The shear membranes used were plywood and oriented strand board (OSB). Tests were conducted to determine the effects of the placement of the shear membrane on the exposed/unexposed face, type of shear membrane, insulation type, load intensity and resilient channel installations on the fire resistance of gypsum board protected, wood stud shear wall assemblies. Details of the results, including the temperatures and deflections measured during the fire tests, are presented. ACKNOWLEDGEMENTS This research is part of a consortium project on the fire resistance and sound performance of wall assemblies - Phase II, among the following partners: . Canadian Wood Council . Canadian Home Builders Association . Canadian Sheet Steel Building Institute . Gypsum Manufacturers of Canada . Owens-Corning Canada . Roxul Inc.

V. K. R. Sultan; M. A. Denham; V. K. R. Kodur; M. A. Sultan; E. M. A. Denham; Canadian Wood Council; Shear Walls; Shear Walls; Shear Walls; Shear Walls

1996-01-01T23:59:59.000Z

471

An Overview of the Louisiana Secondary Wood Products Industry  

E-Print Network (OSTI)

the State of Louisiana. In addition, because the origin of material purchased from in-state suppliers cannot of the development of buying or manufacturing cooperatives that could create purchasing and sales/marketing leverage Secondary Wood Product Manufacturers Number of Employees by Establishment (Percent of respondent companies

472

Production of chemical feedstock by the methanolysis of wood  

DOE Patents (OSTI)

A process for the production of ethylene, benzene and carbon monoxide from particulated biomass such as wood by reaction with methane at a temperature of from 700.degree. C. to 1200.degree. C., at a pressure of from 20 psi to 100 psi for a period of from 0.2 to 10 seconds.

Steinberg, Meyer (Melville, NY); Fallon, Peter (East Moriches, NY)

1984-07-31T23:59:59.000Z

473

Vertical feed stick wood fuel burning furnace system  

DOE Patents (OSTI)

A new and improved stove or furnace for efficient combustion of wood fuel including a vertical feed combustion chamber for receiving and supporting wood fuel in a vertical attitude or stack, a major upper portion of the combustion chamber column comprising a water jacket for coupling to a source of water or heat transfer fluid and for convection circulation of the fluid for confining the locus of wood fuel combustion to the bottom of the vertical gravity feed combustion chamber. A flue gas propagation delay channel extending from the laterally directed draft outlet affords delayed travel time in a high temperature environment to assure substantially complete combustion of the gaseous products of wood burning with forced air as an actively induced draft draws the fuel gas and air mixture laterally through the combustion and high temperature zone. Active sources of forced air and induced draft are included, multiple use and circuit couplings for the recovered heat, and construction features in the refractory material substructure and metal component superstructure.

Hill, Richard C. (Orono, ME)

1984-01-01T23:59:59.000Z

474

Vertical feed stick wood fuel burning furnace system  

DOE Patents (OSTI)

A stove or furnace for efficient combustion of wood fuel includes a vertical feed combustion chamber (15) for receiving and supporting wood fuel in a vertical attitude or stack. A major upper portion of the combustion chamber column comprises a water jacket (14) for coupling to a source of water or heat transfer fluid for convection circulation of the fluid. The locus (31) of wood fuel combustion is thereby confined to the refractory base of the combustion chamber. A flue gas propagation delay channel (34) extending laterally from the base of the chamber affords delayed travel time in a high temperature refractory environment sufficient to assure substantially complete combustion of the gaseous products of wood burning with forced air prior to extraction of heat in heat exchanger (16). Induced draft draws the fuel gas and air mixture laterally through the combustion chamber and refractory high temperature zone to the heat exchanger and flue. Also included are active sources of forced air and induced draft, multiple circuit couplings for the recovered heat, and construction features in the refractory material substructure and metal component superstructure.

Hill, Richard C. (Orono, ME)

1982-01-01T23:59:59.000Z

475

Wood pellet market and trade: a global perspective  

SciTech Connect

This perspective provides an overview of wood pellet markets in a number of countries of high significance, together with an inventory of market factors and relevant past or existing policies. In 2010, the estimated global wood pellet production and consumption were close to 14.3 Mt (million metric tonnes) and 13.5 Mt, respectively, while the global installed production capacity had reached over 28 Mt. Two types of pellets are mainly traded (i) for residential heating and (ii) for large-scale district heating or co-fi ring installations. The EU was the primary market, responsible for nearly 61% and 85% of global production and consumption, respectively in 2010. EU markets were divided according to end use: (i) residential and district heating, (ii) power plants driven market, (iii) mixed market, and (iv) export-driven countries. North America basically serves as an exporter, but also with signifi cant domestic consumption in USA. East Asia is predicted to become the second-largest consumer after the EU in the near future. The development perspective in Latin America remains unclear. Five factors that determine the market characteristics are: (i) the existence of coal-based power plants, (ii) the development of heating systems, (iii) feedstock availability, (iv) interactions with wood industry, and (v) logistics factor. Furthermore, intervention policies play a pivotal role in market development. The perspective of wood pellets industry was also analyzed from four major aspects: (i) supply potential, (ii) logistics issues, (iii) sustainability considerations, and (iv) technology development.

Chun Sheng Goh; Martin Junginger; Maurizio Cocchi; Didier Marchal; Daniela Thran; Christiane Hennig; Jussi Heinimo; Lars Nikolaisen; Peter-Paul Schouwenberg; Douglas Bradley; J. Richard Hess; Jacob J. Jacobson; Leslie Ovard; Michael Deutmeyer

2001-01-01T23:59:59.000Z

476

Environmental Impacts of Preservative-Treated Wood Conference  

E-Print Network (OSTI)

This article was written and prepared by U.S. Government employees on official time, For decades chromated copper arsenate (CCA) was the primary preservative for treated wood used in residential construction. However, recent label changes submitted by CCA registrants will withdraw CCA from most residential applications. This action has increased interest in arsenic-free preservative systems that have been standardized by the American Wood Preservers Association. These include acid copper chromate (ACC), alkaline copper quat (ACQ), copper azole (CBA-A and CA-B), copper citrate (CC), copper dimethyldithiocarbamate (CDDC), and copper HDO (CX-A). All of these CCA alternatives rely on copper as their primary biocide, although some have co-biocides to help prevent attack by copper-tolerant fungi. They have appearance and handling properties similar to CCA and are likely to be readily accepted by consumers. Prior studies indicate that these CCA alternatives release preservative components into the environment at a rate greater than or equal to that of CCA, but because these components have lower mammalian toxicity they are less likely to cause concern in residential applications. As the treated wood industry evolves it is probable that a wider range of types and retentions of wood preservatives will become available, with the treatment more closely tailored to a specific type of construction application.

Stan Lebow

2004-01-01T23:59:59.000Z

477

Wood Products Marketing And Value-Added Opportunities  

E-Print Network (OSTI)

; Vlosky 2002 #12;s The first MDF plant started up four years ago and now there are 3 or 4, so furniture for exotic wood veneer layup. Pressing veneer on MDF will give the most defect-free, flat and smooth surface

478

Scattering of Woods-Saxon Potential in Schrodinger Equation  

E-Print Network (OSTI)

The scattering solutions of the one-dimensional Schrodinger equation for the Woods-Saxon potential are obtained within the position-dependent mass formalism. The wave functions, transmission and reflection coefficients are calculated in terms of Heun's function. These results are also studied for the constant mass case in detail.

Altug Arda; Oktay Aydogdu; Ramazan Sever

2010-09-27T23:59:59.000Z

479

Mitigation for the Endangered Wood Stork on Savannah River Site  

DOE Green Energy (OSTI)

The wood stork is a recently classified federally endangered species. The species forages throughout the facility. The facility impact was mitigated by replacing the affected area with artificially created impoundment. Studies conducted in conjunction with the mitigation have assisted with the recovery effort for this species.

Bryan, A.L.; Coulter, M.C.; Brisbin, I.L.

2000-10-01T23:59:59.000Z

480

Waste Logic Decommissioning Waste Manager 2.0 Users Manual  

Science Conference Proceedings (OSTI)

The Decommissioning Waste Manager, part of EPRI's Waste Logic series of computer programs, analyzes decommissioning waste cost and volume reduction strategies with the intent of quantifying the existing waste management program for any given waste generator.

2001-10-29T23:59:59.000Z

Note: This page contains sample records for the topic "wood waste waste-to-energy" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

RD & D priorities for energy production and resource conservation from municipal solid waste  

Science Conference Proceedings (OSTI)

This report identifies research, development, and demonstration (RD&D) needs and priorities associated with municipal solid waste (MSW) management technologies that conserve or produce energy or resources. The changing character of MSW waste management and the public`s heightened awareness of its real and perceived benefits and costs creates opportunities for RD&D in MSW technologies. Increased recycling, for example, creates new opportunities for energy, chemicals, and materials recovery. New technologies to control and monitor emissions from MSW combustion facilities are available for further improvement or application. Furthermore, emerging waste-to-energy technologies may offer environmental, economic, and other advantages. Given these developments, DOE identified a need to assess the RD&D needs and pdodties and carefully target RD&D efforts to help solve the carbon`s waste management problem and further the National Energy Strategy. This report presents such an assessment. It identifies and Documents RD&D needs and priorities in the broad area of MSW resource . recovery, focusing on efforts to make MSW management technologies commercially viable or to improve their commercial deployment over a 5 to l0 year period. Panels of technical experts identifies 279 RD&D needs in 12 technology areas, ranking about one-fifth of these needs as priorities. A ``Peer Review Group`` identified mass-burn combustion, ``systems studies,`` landfill gas, and ash utilization and disposal as high priority areas for RD&D based on cost and the impacts of further RD&D. The results of this assessment are intended to provide guidance to DOE concerning possible future RD&D projects.

Not Available

1992-08-01T23:59:59.000Z

482

Solid Waste (New Mexico)  

Energy.gov (U.S. Department of Energy (DOE))

The New Mexico Environment Department's Solid Waste Bureau manages solid waste in the state. The Bureau implements and enforces the rules established by the Environmental Improvement Board.

483

Industrial Waste Generation  

NLE Websites -- All DOE Office Websites (Extended Search)

9) Page 2 of 7 Industrial Waste Generation Work with Engineered Nanomaterials Power Consumption Historical Contamination (groundwater, soil) Hazardous Waste Generation Atmospheric...

484

Recycling Electronic Waste - Website  

Science Conference Proceedings (OSTI)

Jun 18, 2010 ... Joined: 2/13/2007. Below is a link to a website that has articles on recycling electronic waste. http://www.scientificamerican....ectronic-waste-...

485

International Trade with Waste.  

E-Print Network (OSTI)

?? In this thesis, trade with waste between developed countries and the third world will be presented to analyze whether waste?trading can create a possible (more)

Willn, Jenny

2008-01-01T23:59:59.000Z

486

Development of polypropylene/wood flour ecocomposites. Evaluation of silane as coupling agent  

SciTech Connect

The effects of Pinus Sylvestris wood flour as filler in polypropylene matrix was evaluated. The mechanical properties and the morphology of different wood flour/polypropylene composites (WPC) were studied. The composites materials were prepared with several amounts of wood flour from 10 to 30% wt. Mechanical properties show that the wood flour incorporation increases the rigidity of the composites. Morphological analysis indicates that agglomerates are formed, with amounts exceeding 30% of wood flour. For the silane--treated composites, the dispersion of the filler into the polypropylene (PP) matrix improved. Shore D hardness of the composites is decreased with the addition of the coupling agent.

Bouza, R.; Barral, L.; Abad, M. J.; Montero, B. [Grupo de Polimeros, Dpto. de Fisica, E.U.P. Ferrol, Universidad de A Coruna, Avda. 19 de Febrero s/n, 15405 Ferrol (Spain)

2010-06-02T23:59:59.000Z

487

Technical and economic review of wood energy systems for military bases  

DOE Green Energy (OSTI)

This report combines two reports dealing with industrial-sized wood combustion technology. As part of its industrial wood combustion effort, SERI's former Industrial Applications and Analysis Branch (IAAB) contracted with the Air Force through the Department of Energy (DOE) to review wood fuels and equipment and to perform an economic sensitivity analysis of small-scale industrial-sized wood combustion investments that might be considered for steam and/or electricity generation at Air Force Bases. Additionally, in 1979, SERI's IAAB contracted with North Carolina State University to produce the Decision Makers' Guide to Wood Fuel for Small Industrial Energy Use. These two reports have been combined to provide the Air Force with a comprehensive guide to wood energy combustion. Discussion is presented under the headings: comparison of wood fuels with conventional boiler fuels; densified biomass; fuel storage; fuel handling and preparation; wood-fired equipment; gasification of wood; retrofitting fossil-fuel boilers; cogeneration; pollution abatement; wood energy system economics and procurement of wood fuels. (DMC)

Flowers, L.; Junge, D.; Levi, M.; O'Grady, M.

1983-06-01T23:59:59.000Z

488

Waste analysis plan for central waste complex  

SciTech Connect

This waste analysis plan (WAP) has been prepared for the Central Waste Complex which is located in the 200 West Area of the Hanford Facility, Richland, Washington. This WAP documents the methods used to characterize, and obtain and analyze representative samples of waste managed at this unit.

Weston, N.L.

1996-09-20T23:59:59.000Z

489

How Much Wood Would a North Country School Chip | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip November 3, 2011 - 11:19am Addthis This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School Alice Dasek Project Officer, Department of Energy State Energy Program

490

How Much Wood Would a North Country School Chip | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip How Much Wood Would a North Country School Chip November 3, 2011 - 11:19am Addthis This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School This is the North Country School's 32,000-square-foot main building. Aligning with the school's commitment to a simple, sustainable lifestyle, the school is heated with a wood chip boiler that uses wood sourced from their sustainably managed woodlot and local forests. | Courtesy of North Country School Alice Dasek Project Officer, Department of Energy State Energy Program

491

Hanford Site annual dangerous waste report: Volume 4, Waste Management Facility report, Radioactive mixed waste  

SciTech Connect

This report contains information on radioactive mixed wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, handling method and containment vessel, waste number, waste designation and amount of waste.

NONE

1994-12-31T23:59:59.000Z

492

Hanford Site annual dangerous waste report: Volume 2, Generator dangerous waste report, radioactive mixed waste  

Science Conference Proceedings (OSTI)

This report contains information on radioactive mixed wastes at the Hanford Site. Information consists of shipment date, physical state, chemical nature, waste description, waste number, waste designation, weight, and waste designation.

NONE

1994-12-31T23:59:59.000Z

493

URBAN WOOD/COAL CO-FIRING IN THE NIOSH BOILER PLANT  

DOE Green Energy (OSTI)

Phase I of this project began by obtaining R&D variances for permits at the NIOSH boilerplant (NBP), Emery Tree Service (ETS) and the J. A. Rutter Company (JARC) for their portions of the project. Wood for the test burn was obtained from the JARC inventory (pallets), Thompson Properties and Seven D Corporation (construction wood), and the Arlington Heights Housing Project (demolition wood). The wood was ground at ETS and JARC, delivered to the Three Rivers Terminal and blended with coal. Three one-day tests using wood/coal blends of 33% wood by volume (both construction wood and demolition wood) were conducted at the NBP. Blends using hammermilled wood were operationally successful. Emissions of SO{sub 2} and NOx decreased and that of CO increased when compared with combusting coal alone. Mercury emissions were measured and evaluated. During the first year of Phase II the principal work focused upon searching for a replacement boilerplant and developing a commercial supply of demolition wood. The NBP withdrew from the project and a search began for another stoker boilerplant in Pennsylvania to replace it on the project. Three potential commercial demolition wood providers were contacted. Two were not be able to supply wood. At the end of the first year of Phase II, discussions were continuing with the third one, a commercial demolition wood provider from northern New Jersey. During the two-and-a-third years of the contract extension it was determined that the demolition wood from northern New Jersey was impractical for use in Pittsburgh, in another power plant in central New Jersey, and in a new wood gasifier being planned in Philadelphia. However, the project team did identify sufficient wood from other sources for the gasifier project. The Principal Investigator of this project assisted a feasibility study of wood gasification in Clarion County, Pennsylvania. As a result of the study, an independent power producer in the county has initiated a small wood gasification project at its site. Throughout much of this total project the Principal Investigator has counseled two small businesses in developing a waxed cardboard pellet business. A recent test burn of this biofuel appears successful and a purchase contract is anticipated soon. During the past two months a major tree-trimming firm has shown an active interest in entering the wood-chip fuel market in the Pittsburgh area and has contacted the NBP, among others, as potential customers. The NBP superintendent is currently in discussion with the facilities management of the Bruceton Research Center about resuming their interest in cofiring this renewable fuel to the stoker there.

James T. Cobb Jr.

2005-02-10T23:59:59.000Z

494

Renewable energy annual 1996  

DOE Green Energy (OSTI)

This report presents summary data on renewable energy consumption, the status of each of the primary renewable technologies, a profile of each of the associated industries, an analysis of topical issues related to renewable energy, and information on renewable energy projects worldwide. It is the second in a series of annual reports on renewable energy. The renewable energy resources included in the report are biomass (wood and ethanol); municipal solid waste, including waste-to-energy and landfill gas; geothermal; wind; and solar energy, including solar thermal and photovoltaic. The report also includes various appendices and a glossary.

NONE

1997-03-01T23:59:59.000Z

495

Effectiveness of three bulking agents for food waste composting  

Science Conference Proceedings (OSTI)

Rather than landfilling, composting the organic fraction of municipal solid wastes recycles the waste as a safe and nutrient enriched soil amendment, reduces emissions of greenhouse gases and generates less leachate. The objective of this project was to investigate the composting effectiveness of three bulking agents, namely chopped wheat (Triticum) straw, chopped mature hay consisting of 80% timothy (milium) and 20% clover (triphullum) and pine (pinus) wood shavings. These bulking agents were each mixed in duplicates at three different ratios with food waste (FW) and composted for 10 days using prototype in-vessel composters to observe their temperature and pH trends. Then, each mixture was matured in vertical barrels for 56 days to measure their mass loss and final nutrient content and to visually evaluate their level of decomposition. Chopped wheat straw (CWS) and chopped hay (CH) were the only two formulas that reached thermophilic temperatures during the 10 days of active composting when mixed with FW at a wet mass ratio of 8.9 and 8.6:1 (FW:CWS and FW:CH), respectively. After 56 days of maturation, these two formulas were well decomposed with no or very few recognizable substrate particles, and offered a final TN exceeding the original. Wood shavings (WS) produced the least decomposed compost at maturation, with wood particles still visible in the final product, and with a TN lower than the initial. Nevertheless, all bulking agents produced compost with an organic matter, TN, TP and TK content suitable for use as soil amendment.

Adhikari, Bijaya K. [Department of Bioresource Engineering, Macdonald Campus of McGill University, 21 111 Lakeshore, Ste Anne de Bellevue (Quebec), H9X 3V9 (Canada); Barrington, Suzelle [Department of Bioresource Engineering, Macdonald Campus of McGill University, 21 111 Lakeshore, Ste Anne de Bellevue (Quebec), H9X 3V9 (Canada)], E-mail: suzelle.barrington@mcgill.ca; Martinez, Jose [Cemagref, Rennes Regional Centre, 7 avenue du Cucille, CS 64427, F-35044 Rennes (France); King, Susan [Department of Bioresource Engineering, Macdonald Campus of McGill University, 21 111 Lakeshore, Ste Anne de Bellevue (Quebec), H9X 3V9 (Canada)

2009-01-15T23:59:59.000Z

496

Analysis of drying wood waste fuels with boiler exhaust gases: simulation, performance, and economics  

DOE Green Energy (OSTI)

This study evaluates the feasibility of retrofitting a rotary dryer to a hog fuel boiler, using the boiler exhaust gases as the drying medium. Two simulation models were developed. Each model accurately predicts system performance given site-specific parameters such as boiler steam demand, fue moisture content, boiler exhaust temperature and combustion excess air. Three rotary dryers/hog fuel boilers currently in operation in the forest products industry were analyzed. The data obtained were used to validate te accuracy of the simulation models and to establish the performance of boiler/dryer systems under field conditions. The boiler exhaust temperatures observed ranged from 340 to 500/sup 0/F and indicated that significant drying could be realized at moderate stack temperatures, as substantitated by experimental moisture content data. The simulation models were used to evaluate a general boiler/dryer system's sensitivity to variation in operating conditions. The sensitivity analyses indicated that under moderate conditions (400/sup 0/F boiler exhaust, etc.) the installation of a rotary dryer results in a 15% increase in boiler efficiency and a 13% decrease in fuel consumption. Both the field data and sensitivity analyses indicated that a greater increase in boiler efficiency could be realized at higher stack temperatures, approximately a 30% increase in boiler efficiency for a stack temperature of 600/sup 0/F. The cash flow basis payback periods based on hog fuel savings due to dryer installation ranged from 2.7 years for a used dryer to 3.9 years for a new dryer. The payback periods for equivalent BTU savings of gas and oil ranged from 1.2 to 2.0 for gas and from 1.3 to 2.1 years for oil. This study concludes that retrofitting a rotary dryer to an existing hog fuel boiler is an economically feasible option to the forest products industry. 31 references, 24 figures, 18 tables.

Kirk, R.W.; Wilson, J.B.

1984-09-01T23:59:59.000Z

497

Today in Energy - U.S. Energy Information Administration (EIA)  

U.S. Energy Information Administration (EIA)

Nuclear & Uranium. Uranium fuel ... waste-to-energy September 18, 2012 More recycling raises average energy content of waste used to generate electricity. September ...

498

Infectious waste feed system  

DOE Patents (OSTI)

An infectious waste feed system for comminuting infectious waste and feeding the comminuted waste to a combustor automatically without the need for human intervention. The system includes a receptacle for accepting waste materials. Preferably, the receptacle includes a first and second compartment and a means for sealing the first and second compartments from the atmosphere. A shredder is disposed to comminute waste materials accepted in the receptacle to a predetermined size. A trough is disposed to receive the comminuted waste materials from the shredder. A feeding means is disposed within the trough and is movable in a first and second direction for feeding the comminuted waste materials to a combustor.

Coulthard, E. James (York, PA)

1994-01-01T23:59:59.000Z

499

Understanding radioactive waste  

SciTech Connect

This document contains information on all aspects of radioactive wastes. Facts are presented about radioactive wastes simply, clearly and in an unbiased manner which makes the information readily accessible to the interested public. The contents are as follows: questions and concerns about wastes; atoms and chemistry; radioactivity; kinds of radiation; biological effects of radiation; radiation standards and protection; fission and fission products; the Manhattan Project; defense and development; uses of isotopes and radiation; classification of wastes; spent fuels from nuclear reactors; storage of spent fuel; reprocessing, recycling, and resources; uranium mill tailings; low-level wastes; transportation; methods of handling high-level nuclear wastes; project salt vault; multiple barrier approach; research on waste isolation; legal requiremnts; the national waste management program; societal aspects of radioactive wastes; perspectives; glossary; appendix A (scientific American articles); appendix B (reference material on wastes). (ATT)

Murray, R.L.

1981-12-01T23:59:59.000Z

500

Nuclear waste solidification  

DOE Patents (OSTI)

High level liquid waste solidification is achieved on a continuous basis by atomizing the liquid waste and introducing the atomized liquid waste into a reaction chamber including a fluidized, heated inert bed to effect calcination of the atomized waste and removal of the calcined waste by overflow removal and by attrition and elutriation from the reaction chamber, and feeding additional inert bed particles to the fluidized bed to maintain the inert bed composition.

Bjorklund, William J. (Richland, WA)

1977-01-01T23:59:59.000Z