Powered by Deep Web Technologies
Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

34th annual reed rotary rig census  

SciTech Connect

This article reports that the number of rigs active according to the 1986 census is 1052, which represents a decline of 1573 rigs from 1985 figures. This 60 percent decrease is the largest decline of active rigs in the 34-year history of the census. The 1986 census takers found 3993 rigs are available with the capacity to drill deeper than 3000 ft. The count has thus declined by 416 rigs (9 percent) from the 1985 total of 4409. Rig availability declined for the fourth consecutive year following nine straight years of fleet expansion (1974-1982). During the past four years, 1651 rigs have been removed from the drilling fleet representing a 29 percent decline from the record high number of rigs available in 1982. The 1986 decline in the available U.S. fleet is considerably less than what many industry observers had been anticipating. A larger decrease in the rig fleet has not been realized for a number of reasons.

Hutchinson, D.L.; Pastusek, P.E.

1986-10-01T23:59:59.000Z

2

Table 4.4 Crude Oil and Natural Gas Rotary Rigs in ...  

U.S. Energy Information Administration (EIA)

Table 4.4 Crude Oil and Natural Gas Rotary Rigs in Operation, 1949-2011 (Number of Rigs) Year: By Site : By Type: Total 1: Onshore

3

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation ...  

U.S. Energy Information Administration (EIA)

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation (Number of Elements) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1973: 99: 89: 90: 79: 72 ...

4

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation ...  

U.S. Energy Information Administration (EIA)

U.S. Offshore Crude Oil and Natural Gas Rotary Rigs in Operation (Number of Elements) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9 ...

5

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number of ...  

U.S. Energy Information Administration (EIA)

U.S. Crude Oil and Natural Gas Rotary Rigs in Operation (Number of Elements) Year Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec; 1973: 1,219: 1,126: 1,049: 993 ...

6

rig_specs.indd  

NLE Websites -- All DOE Office Websites (Extended Search)

RIG SPECIFICATIONS R MOTC Rig No. 1 is a 2005 Crown (Calgary, Canada) trailer-mounted drilling rig. It incor- porates several features found desirable over numerous drilling tests...

7

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

12-i Chapter 12 Rigging Hardware CHAPTER 12 RIGGING HARDWARE This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, eye nuts, links, rings, swivels, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices and implements the requirements of ANSI/ASME B30.26, "Rigging Hardware" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 12.1 GENERAL..................................................................................................................................12-1 12.1.1 Good and Bad Rigging Practices ...................................................................................12-1 12.2 RIGGING HOOKS.....................................................................................................................12-5

8

Hoisting & Rigging Fundamentals  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting and Rigging Hoisting and Rigging Fundamentals for Riaaers and ODerators Pendant Control - Components TR244C, Rev. 5 December 2002 TR244C Rev . 5 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii HOISTING AND RIGGING OBJECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 WIRE ROPE SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SYNTHETIC WEBBING SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I O CHAINSLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 METAL MESH SLINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SPREADER BEAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 RIGGING HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9

Hoisting & Rigging Lift Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

Authorized Personnel (attach more sheets if necessary) Printed name Signature Date SSRL Hoisting & Rigging Lift Plan Stanford Synchrotron Radiation Laboratory May 16, 2005...

10

A rigged market  

SciTech Connect

The mobile rig market remains a unique sector of the global upstream oil and gas industry. Big oil is continuing to emerge blinking from the darkness of its recent cash-starved existence to bask in the glory of a resurgent oil price. But the rig sector is once again lagging behind the pace being set by operators as they open up their wallets for new or delayed exploration and production projects. This paper gives statistics on worldwide count and contracts.

Thomas, M.

2000-02-01T23:59:59.000Z

11

MHK Technologies/Ocean Energy Rig | Open Energy Information  

Open Energy Info (EERE)

Rig Rig < MHK Technologies Jump to: navigation, search << Return to the MHK database homepage Ocean Energy Rig.jpg Technology Profile Primary Organization Free Flow 69 Technology Resource Click here Current Technology Type Click here Axial Flow Turbine Technology Readiness Level Click here TRL 4 Proof of Concept Technology Description The Ocean Energy Rig is a hybrid concept harnessing tidal stream with increased velocity from venturi system wave and wind power The rig also uses solar panels to power computers and warning lights Other unique features include a water ballasting system with automatic self levelling and wave ramps to maximize FreeFlow 69 s new wave power device It is envisaged that the Ocean Energy Rig would be assembled and maintained in dry docks and would be towed out into position before being semi submerged and anchored for operation Power output of the production model would be at least 10MW

12

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DOE-STD-1090-2011 DOE-STD-1090-2011 September 2011 Superseding DOE-STD-1090-2007 August 2007 DOE STANDARD HOISTING AND RIGGING U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND INTENTIONALLY BLANK DOE-STD-1090-2011 iii Introduction The U.S. Department of Energy (DOE) Hoisting and Rigging Standard is intended to be used by supervisors, line managers, safety personnel, equipment operators, riggers and other personnel responsible for the safety of hoisting and rigging operations at DOE sites. It may be used as either contract document or as a best practices guide at the site's or program office's discretion. The standard invokes applicable OSHA and national consensus standards but also delineates

13

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

13-i CHAPTER 13 LOAD HOOKS This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

14

Rig scarcity prompts innovative drilling solution  

Science Conference Proceedings (OSTI)

Unable to locate a shallow-water offshore rig for its program in Indonesia, British Gas International developed an innovative pad/ballasted barge configuration to utilize a land rig, which was available. Many non-typical problems were encountered and solved to establish the drilling location 600 m (2,000 ft) from the shore in Bintuni Bay in Irian Jaya, eastern Indonesia. The final hybrid configuration has sparked interesting debate as to whether the operation should be designated as onshore or offshore. The paper discusses the project overview, concept development, construction, and operations.

Lattimore, G.M.; Gott, T.; Feagin, J.

1997-11-01T23:59:59.000Z

15

Self propelled drilling rig starts offshore exploration  

SciTech Connect

Ocean Drilling and Exploration Co. recently commissioned its new $12 million self-propelled, semisubmersible drilling rig, Ocean Prospector, at Mitsubishi Shipyard, Japan, where the rig was built. Initial trail runs completed adjacent to the shipyard indicated that the ship has a speed of 7 kn ahead and 3 kn astern. Steering also is reported to be excellent. The rig has a minimum turning radius of approx. 2 barge lengths and shows instant response. This rig is powered by 4 Fairbanks Morse, 10-cylinder opposed piston, model 38D8-1/8 diesel engines. Each engine is rated at 1,600 hp at 720 rpm and they drive eight 1,600 kw, traction type D-C generators and two 1,000 kw A-C generators. The rated operating depth of the unit afloat is 600 ft of water. The overall length of Ocean Prospector is just over 344 ft, with the beam measuring 263-1/2 ft. During transit, when the rig will be completely deballasted, it will have a draft of approx. 20 ft. When it reaches the drilling site, ballast water will be pumped into the 18 ballast tanks until the draft is increased to 70 ft. At this point, the underside of the main deck will be 50 ft above the mean surface of the sea. Drilling operations will be conducted while the rig is at the 70 ft draft. The mooring system will consist of eight 2-3/4 in. chains, each measuring 3,300 ft in length and connected to a 15-ton anchor.

1971-05-01T23:59:59.000Z

16

Program: Hoisting and Rigging  

E-Print Network (OSTI)

The purpose of these requirements is to ensure that hoisting and rigging (H&R) equipment is safe to operate. 2 Scope These requirements cover inspections and maintenance over the life of H&R equipment. Requirements are listed in terms of ? Types of inspection (initial, pre-use, frequent, periodic, and third party) and maintenance (preventative, operational testing, and load testing) Responsibilities (person who ensures that the inspection was performed and person performing the inspection) Documentation requirements – HRED refers to the H&R Equipment Database, which is maintained by the H&R inspector. Submit inspection and maintenance data to this inspector to stay in compliance. – CR refers to custodian records, which are maintained by the equipment custodian. Details on what to look for and how to conduct the inspection are listed in Department of Energy Standard 1090, “Hoisting and Rigging ” (DOE-STD-1090-2007).

unknown authors

2009-01-01T23:59:59.000Z

17

Joint venture builds new rigs  

Science Conference Proceedings (OSTI)

Recent emphasis on increasing drilling efficiency and avoiding additional environmental damage has led Russian operator Gazprom to specify a new generation drilling rig for exploratory and development drilling in the Astrakhan gas/condensate field in southwestern Russia. The two rigs on order combine Russian and American technology and include a unique system for processing contaminated drill cuttings. The article describes the rig package and cuttings treatment system.

NONE

1995-05-01T23:59:59.000Z

18

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

19

Hoisting & Rigging Assessment Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING HOISTING & RIGGING Assessment Plan NNSA/Nevada Site Office Facility Representative Division Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging

20

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1-i 1-i CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging and implements the requirements of ASME B30.9, Slings (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). . 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays .........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices" (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials are governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

22

Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

SciTech Connect

This standard is intended as a reference document to be used by supervisors, line managers, safety personnel, equipment operators, and any other personnel responsible for safety of hoisting and rigging operations at DOE sites. It quotes or paraphrases the US OSHA and ANSI requirements. It also encompasses, under one cover,hoisting and rigging requirements, codes, standards, and regulations, eliminating the need to maintain extensive (and often incomplete) libraries of hoisting and rigging standards throughout DOE. The standard occasionally goes beyond the minimum general industry standards established by OSHA and ANSI, and also delineates the more stringent requirements necessary to accomplish the complex, diversified, critical, and often hazardous hoisting and rigging work found with the DOE complex.

NONE

1995-06-01T23:59:59.000Z

23

Hoisting and Rigging: Inspection and Maintenance Requirements  

E-Print Network (OSTI)

Devices, Slings, and Rigging Hardware and Accessories (SLAC-I-730-0A21S-036) Hoisting and Rigging: PreHoisting and Rigging: Inspection and Maintenance Requirements URL: http://www-group.slac.stanford.edu/esh/eshmanual/references/hoisting Department: Field Safety and Building Inspection Program: Hoisting and Rigging Authority: ESH Manual, Chapter

Wechsler, Risa H.

24

Rotary drive mechanism  

Science Conference Proceedings (OSTI)

This patent describes a rotary drive mechanism which includes a rotary solenoid having a stator and multi-poled rotor. A moving member rotates with the rotor and is biased by a biasing device. The biasing device causes a further rotational movement after rotation by the rotary solenoid. Thus, energization of the rotary solenoid moves the member in one direction to one position and biases the biasing device against the member. Subsequently, de- energization of the rotary solenoid causes the biasing device to move the member in the same direction to another position from where the moving member is again movable by energization and de-energization of the rotary solenoid. Preferably, the moving member is a multi-lobed cam having the same number of lobes as the rotor has poles. An anti- overdrive device is also preferably provided for preventing overdrive in the forward direction or a reverse rotation of the moving member and for precisely aligning the moving member.

Kenderdine, E.W.

1991-10-08T23:59:59.000Z

25

Rotary drive mechanism  

Science Conference Proceedings (OSTI)

A rotary drive mechanism includes a rotary solenoid having a stator and multi-poled rotor. A moving member rotates with the rotor and is biased by a biasing device. The biasing device causes a further rotational movement after rotation by the rotary solenoid. Thus, energization of the rotary solenoid moves the member in one direction to one position and biases the biasing device against the member. Subsequently, de-energization of the rotary solenoid causes the biasing device to move the member in the same direction to another position from where the moving member is again movable by energization and de-energization of the rotary solenoid. Preferably, the moving member is a multi-lobed cam having the same number of lobes as the rotor has poles. An anti-overdrive device is also preferably provided for preventing overdrive in the forward direction or a reverse rotation of the moving member and for precisely aligning the moving member.

Kenderdine, Eugene W. (Albuquerque, NM)

1991-01-01T23:59:59.000Z

26

EM Rotary Filter Program  

Electrical Junction Box Motors for Rotary Microfilters Motor Operated Valves Electrical ... savings SMPs Clarified Salt Solution Pumping System Sr-90 and actinides

27

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9-2004 9-2004 12-i Chapter 12 Rigging Accessories CHAPTER 12 RIGGING ACCESSORIES This chapter provides requirements for rigging accessories used in hoisting and rigging - shackles, eyebolts, rings, wire-rope clips, turnbuckles, rigging hooks, and load-indicating devices. 12.1 GENERAL ...............................................................................................................................12-1 12.1.1 Inspections .................................................................................................................12-1 12.1.2 Testing .....................................................................................................................12-3 12.1.3 Good and Bad Rigging Practices ...............................................................................12-3

28

PNNL Hoisting and Rigging Manual  

Science Conference Proceedings (OSTI)

This manual describes the safe and cost effective operation, inspection, maintenance, and repair requirements for cranes, hoists, fork trucks, slings, rigging hardware, and hoisting equipment. It is intended to be a user's guide to requirements, codes, laws, regulations, standards, and practices that apply to Pacific Northwest National Laboratory (PNNL) and its subcontractors.

Haynie, Todd O.; Fullmer, Michael W.

2008-12-29T23:59:59.000Z

29

Hoisting and rigging manual: Uncontrolled document  

Science Conference Proceedings (OSTI)

This document is a draft copy of a Hoisting and Rigging Manual for the Department of Energy. The manual is divided into ten chapters. The chapter titles follow: terminology and definitions; operator training and qualification; overhead and gantry cranes; mobile cranes; forklift trucks; hoists; hooks; wire rope, slings, and rigging accessories; construction hoisting and rigging equipment requirements; references.

NONE

1991-05-01T23:59:59.000Z

30

Hoisting & Rigging Lift Plan  

NLE Websites -- All DOE Office Websites (Extended Search)

Hoisting & Rigging Lift Plan Hoisting & Rigging Lift Plan Stanford Synchrotron Radiation Laboratory May 16, 2005 SSRL-HRLP-000-R0 Page 1 of 3 General Information Lift Plan Document # Plan prepared by: Describe the load or items to be lifted: Could the load, if dropped, release hazardous materials or radioactivity? No Yes (describe) Is the load irreplaceable or would it be very costly to replace if damaged? No Yes (describe) Brief description of lift activities (specify if rolling or flipping involved) Equipment Information Equipment ID: Equipment custodian: Rated capacity: Operator capacity : Personnel Protective Equipment (PPE) Steel-toed shoes Required for all personnel involved with lift activity to protect from crushing of feet/toes

31

Somebody better find some rigs  

SciTech Connect

The paper discusses the outlook for the gas and oil industries of the Middle East. Field development projects abound, as the larger exporting nations pursue ambitious policies of production expansion. However, their plans may be hampered by the growing worldwide shortage of rigs. Separate evaluations are given for Saudi Arabia, Kuwait, Neutral Zone, Abu Dhabi, Iran, Iraq, Qatar, Yemen, Syria, Dubai, Turkey, Sharjah, and briefly for Bahrain, Israel, Jordan, UAE-Ajman, and UAE-Ras al-Khaimah.

NONE

1997-08-01T23:59:59.000Z

32

Modular designs highlight several new rigs  

SciTech Connect

A new platform drilling rig for offshore Trinidad and two new land rigs for the former Soviet Union feature the latest in drilling and construction technology and modular components for quick rig up/rig down. The Sundowner 801 was mock-up tested in Galveston, TX, a few weeks ago in preparation for its load-out to the Dolphin field offshore Trinidad. Two other new units, UNOC 500 DE series land rigs, were recently constructed and mock-up tested in Ekaterinburg, Russia, for upcoming exploratory work for RAO Gazprom, a large natural gas producer in Russia. These rigs are unique in that they were constructed from new components made both in the US and in Russia. The paper describes all three units.

Rappold, K.

1995-12-04T23:59:59.000Z

33

Rotary mechanical latch  

Science Conference Proceedings (OSTI)

A rotary mechanical latch for positive latching and unlatching of a rotary device with a latchable rotating assembly having a latching gear that can be driven to latched and unlatched states by a drive mechanism such as an electric motor. A cam arm affixed to the latching gear interfaces with leading and trailing latch cams affixed to a flange within the drive mechanism. The interaction of the cam arm with leading and trailing latch cams prevents rotation of the rotating assembly by external forces such as those due to vibration or tampering.

Spletzer, Barry L.; Martinez, Michael A.; Marron, Lisa C.

2012-11-13T23:59:59.000Z

34

Solar heated rotary kiln  

SciTech Connect

A solar heated rotary kiln utilized for decomposition of materials, such as zinc sulfate. The rotary kiln has an open end and is enclosed in a sealed container having a window positioned for directing solar energy into the open end of the kiln. The material to be decomposed is directed through the container into the kiln by a feed tube. The container is also provided with an outlet for exhaust gases and an outlet for spent solids, and rests on a tiltable base. The window may be cooled and kept clear of debris by coolant gases.

Shell, Pamela K. (Tracy, CA)

1984-01-01T23:59:59.000Z

35

Scheduling Workover Rigs for Onshore Oil Production  

E-Print Network (OSTI)

available workover rigs, so as to minimize the production loss associated with the ... novic [5, 6, 7] is based on the exploration of a dynamic neighborhood model.

36

Rotary shaft sealing assembly  

DOE Patents (OSTI)

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Dietle, Lannie L. (Houston, TX); Schroeder, John E. (Richmond, TX); Kalsi, Manmohan S. (Houston, TX); Alvarez, Patricio D. (Richmond, TX)

2010-09-21T23:59:59.000Z

37

Rotary shaft sealing assembly  

DOE Patents (OSTI)

A rotary shaft sealing assembly in which a first fluid is partitioned from a second fluid in a housing assembly having a rotary shaft located at least partially within. In one embodiment a lip seal is lubricated and flushed with a pressure-generating seal ring preferably having an angled diverting feature. The pressure-generating seal ring and a hydrodynamic seal may be used to define a lubricant-filled region with each of the seals having hydrodynamic inlets facing the lubricant-filled region. Another aspect of the sealing assembly is having a seal to contain pressurized lubricant while withstanding high rotary speeds. Another rotary shaft sealing assembly embodiment includes a lubricant supply providing a lubricant at an elevated pressure to a region between a lip seal and a hydrodynamic seal with a flow control regulating the flow of lubricant past the lip seal. The hydrodynamic seal may include an energizer element having a modulus of elasticity greater than the modulus of elasticity of a sealing lip of the hydrodynamic seal.

Dietle, Lannie L; Schroeder, John E; Kalsi, Manmohan S; Alvarez, Patricio D

2013-08-13T23:59:59.000Z

38

Rotary magnetic heat pump  

DOE Patents (OSTI)

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation.

Kirol, Lance D. (Shelly, ID)

1988-01-01T23:59:59.000Z

39

Rotary pneumatic valve  

DOE Patents (OSTI)

A rotary pneumatic valve which is thrust balanced and the pneumatic pressure developed produces only radial loads on the valve cylinder producing negligible resistance and thus minimal torque on the bearings of the valve. The valve is multiplexed such that at least two complete switching cycles occur for each revolution of the cylinder spindle. 4 figs.

Hardee, H.C.

1989-08-02T23:59:59.000Z

40

Rotary Burner Demonstration  

Science Conference Proceedings (OSTI)

The subject technology, the Calcpos Rotary Burner (CRB), is a burner that is proposed to reduce energy consumption and emission levels in comparison to currently available technology. burners are used throughout industry to produce the heat that is required during the refining process. Refineries seek to minimize the use of energy in refining while still meeting EPA regulations for emissions.

Paul Flanagan

2003-04-30T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

Rotary magnetic heat pump  

DOE Patents (OSTI)

A rotary magnetic heat pump constructed without flow seals or segmented rotor accomplishes recuperation and regeneration by using split flow paths. Heat exchange fluid pumped through heat exchangers and returned to the heat pump splits into two flow components: one flowing counter to the rotor rotation and one flowing with the rotation. 5 figs.

Kirol, L.D.

1987-02-11T23:59:59.000Z

42

Scheduling workover rigs for onshore oil production  

Science Conference Proceedings (OSTI)

Many oil wells in Brazilian onshore fields rely on artificial lift methods. Maintenance services such as cleaning, reinstatement, stimulation and others are essential to these wells. These services are performed by workover rigs, which are available ... Keywords: Combinatorial optimization, Heuristics, Oil production, VNS, Workover rigs

Dario J. Aloise; Daniel Aloise; Caroline T. M. Rocha; Celso C. Ribeiro; José C. Ribeiro Filho; Luiz S. S. Moura

2006-04-01T23:59:59.000Z

43

Operators wary: Stack that rig correctly  

SciTech Connect

This article points out that reasons for planned, scheduled preservation of offshore rigs and equipment are as varied as the owner's interest in them. As a result, no single plan or procedure can meet the requirements of every rig owner. Each rig and its equipment must be treated individually for a number of reasons. The most effective and economical rig preservation program is the result of both the owner and preservation contractor understanding all the objectives and the time frame involved. Numerous questions should be answered up front. How long will preservation measures be required. Is the rig to be maintained in an operational state. Will there be frequent trips to the rig. Will the unit be kept intact, or equipment removed as needed for operation of other rigs. Is the whole unit or any of its components for sale. Will insurance and certifications be affected by the preservation methods used. Perhaps most important is the time period. If the rig is to be stacked for an extended length of time, the owner will likely opt for ''cold,'' or inoperable, preservation. In this condition, engines are treated to protect cylinders, cooling systems and drive components in a static condition.

Moriniere, J.

1987-07-01T23:59:59.000Z

44

Recirculating rotary gas compressor  

DOE Patents (OSTI)

A positive displacement, recirculating Roots-type rotary gas compressor is described which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits which return compressed discharge gas to the compressor housing, where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor. 12 figs.

Weinbrecht, J.F.

1992-02-25T23:59:59.000Z

45

Recirculating rotary gas compressor  

DOE Patents (OSTI)

A positive displacement, recirculating Roots-type rotary gas compressor which operates on the basis of flow work compression. The compressor includes a pair of large diameter recirculation conduits (24 and 26) which return compressed discharge gas to the compressor housing (14), where it is mixed with low pressure inlet gas, thereby minimizing adiabatic heating of the gas. The compressor includes a pair of involutely lobed impellers (10 and 12) and an associated port configuration which together result in uninterrupted flow of recirculation gas. The large diameter recirculation conduits equalize gas flow velocities within the compressor and minimize gas flow losses. The compressor is particularly suited to applications requiring sustained operation at higher gas compression ratios than have previously been feasible with rotary pumps, and is particularly applicable to refrigeration or other applications requiring condensation of a vapor.

Weinbrecht, John F. (601 Oakwood Loop, NE., Albuquerque, NM 87123)

1992-01-01T23:59:59.000Z

46

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i Chapter 15 Construction Hoisting and Rigging Equipment Requirements This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3

47

Study on an Electric Drilling Rig with Hydraulic Energy Storage  

Science Conference Proceedings (OSTI)

An electric drilling rig with hydraulic energy storage is researched. This rig can recover the potential energy of the drill stem lowered and owns remarkable energy-saving effect. The mathematical model of the new rig lifting the drill stem was deduced ... Keywords: electric drilling rig, energy-recovering, energy-saving

Zhang Lujun

2010-06-01T23:59:59.000Z

48

Toolpusher is key to efficient rig operation  

Science Conference Proceedings (OSTI)

Toolpushers earn a higher salary, control more personnel, and are responsible for a more expensive operation than many graduate MBAs. As a result, toolpushers are key to improved rig efficiencies and reduced crew turnover. For example, by having its toolpushers in Libya implement a new managerial approach, Santa Fe Drilling Co. reduced labor turnover 30%, reduced the number of lost-time accidents 58%, and increased average rig inspection scores 6%. During the boom years of drilling, toolpushers complained often about the poor quality of roustabouts and roughnecks assigned to them. Many toolpushers held poor screening of personnel responsible, and felt justified in firing those who were slow to adapt. Few of them considered that they were directly responsible. Today's toolpusher must realize that he is responsible not only for the rig, its maintenance, and its drilling performance, but for training and development of the rig's personnel as well.

Fortney, K.

1983-09-01T23:59:59.000Z

49

,,,,,"Rig: TOI Discoverer Enterprise"  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" Well: OCS-G 32306 002 ST00BP00",,,,"Flow Data" ,,,,,"Field: Mississippi Canyon 252" ,,,,,"Rig: TOI Discoverer Enterprise" ,,,,,"Choke Manifold",,,,"Rates",,,,,,,,,"Ratio" "Date","Time","Choke A","Choke B","BSW","WHPres","WHTemp","WHDCP","WHDCTemp","Gas Rate","Gas Cum","Uncorrected ","Uncorrected ","Water Rate","Water Cum","Uncorrected ","Uncorrected ","Cumulative Oil ","GOR1","Comments" ,,,,,,,,,,,"Oil Rate","Oil Cum ",,,"Liquid Rate","Liquid Cum","from Cargo "

50

Unique rig designed for northern areas  

SciTech Connect

The development of a new generation of drilling and support vessels specially designed to allow year-round drilling off the northern coast of Norway is discussed. New and better equipment is necessary so year-round operations can be done safely and without danger to the environment. To achieve that, a specially designed drilling rig, as well as support and standby vessels are being developed. A quantitative safety analysis of the rig is presently being carried out. The rig will be highly computerized. The computer software will contain programs for stability calculation, ballast recommendation, automatic trim, automatic ballast, automatic mud mix, strain/stress monitoring, dynamic stability, warehouse/maintenance and drilling data acquisition.

1984-05-01T23:59:59.000Z

51

Mixed Stream Test Rig (MISTER) Startup Report  

DOE Green Energy (OSTI)

This report describes the work accomplished to date to design, procure, assemble, authorize, and startup the Mixed Stream Test Rig (MISTER) at the Idaho National Laboratory (INL). It describes the reasons for establishing this capability, physical configuration of the test equipment, operations methodology, initial success, and plans for completing the initial 1,000 hour test.

Charles Park

2011-02-01T23:59:59.000Z

52

Table 4.4 Crude Oil and Natural Gas Rotary Rigs in ...  

U.S. Energy Information Administration (EIA)

1954. na: na: na: na: 2,508: 1955. na: na: na: na: 2,686: 1956. na: na: na: na: 2,620: 1957. na: na: na: na: 2,426: 1958. na: na: na: na: 1,922: 1959. ...

53

U.S. Onshore Crude Oil and Natural Gas Rotary Rigs in ...  

U.S. Energy Information Administration (EIA)

1,954: 1,979: 2,016: 2,066: 2,103: 2,122: 2,127: 2,138: 2,156: 2,169: 2,098: 1979: 1,992: 1,858: 1,768: 1,736: 1,762: 1,794: 1,889: 2,014: 2,069: ...

54

DOE-STD-1090-99; DOE Standard Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

NLE Websites -- All DOE Office Websites (Extended Search)

TS TS INCH-POUND DOE-STD-1090-99 March 1999 Superseding DOE-STD-1090-96 September 1996 DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) U.S. Department of Energy AREA SAFT Washington, D.C. 20585 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. This document has been reproduced from the best available copy. Available to DOE and DOE contractors from ES&H Technical Information Services, U.S. Department of Energy, (800) 473-4375, fax: (301) 903-9823. Available to the public from the U.S. Department of Commerce, Technology Administration, National Technical Information Service, Springfield, VA 22161; (703) 605-6000. DOE STANDARD HOISTING AND RIGGING (Formerly Hoisting and Rigging Manual) Summary of Changes as of March 1999

55

ADVANCED HOT SECTION MATERIALS AND COATINGS TEST RIG  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principal activity during this reporting period were the evaluation of syngas combustor concepts, the evaluation of test section concepts and the selection of the preferred rig configuration.

Scott Reome; Dan Davies

2004-04-30T23:59:59.000Z

56

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 CONSTRUCTION HOISTING AND RIGGING EQUIPMENT REQUIREMENTS 15-i This chapter outlines the requirements for the safe use of hoisting and rigging equipment on construction projects at DOE installations. 15.1 GENERAL ...............................................................................................................................15-1 15.2 PERSONNEL QUALIFICATIONS.........................................................................................15-2 15.2.1 Qualified Operators of Mobile Cranes.......................................................................15-2 15.2.2 Qualified Operators of Forklift Trucks ......................................................................15-3 15.2.3 Qualified Riggers .......................................................................................................15-4

57

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 LOAD HOOKS 13-i Chapter 13 Load Hooks This chapter provides safety standards for the inspection, testing, and maintenance of load hooks installed on cranes or hoists and implements the requirements of ASME B30.10, Chapter 10-1, "Hooks." See Chapter 12, "Rigging Accessories," for rigging hook requirements. 13.1 GENERAL ...............................................................................................................................13-1 13.1.1 Marking......................................................................................................................13-1 13.1.2 Attachments ...............................................................................................................13-1

58

Rotary kiln seal  

SciTech Connect

A rotary seal used to prevent the escape of contaminates from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminates pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Drexler, Robert L. (Idaho Falls, ID)

1992-01-01T23:59:59.000Z

59

Rotary kiln seal  

DOE Patents (OSTI)

A rotary seal used to prevent the escape of contaminants from a rotating kiln incinerator. The rotating seal combines a rotating disc plate which is attached to the rotating kiln shell and four sets of non-rotating carbon seal bars housed in a primary and secondary housing and which rub on the sides of the disc. A seal air system is used to create a positive pressure in a chamber between the primary and secondary seals to create a positive air flow into the contaminated gas chamber. The seal air system also employs an air inlet located between the secondary and tertiary seals to further insure that no contaminants pass the seal and enter the external environment and to provide makeup air for the air which flows into the contaminated gas chamber. The pressure exerted by the seal bars on the rotating disc is controlled by means of a preload spring. The seal is capable of operating in a thermally changing environment where the both radial expansion and axial movement of the rotating kiln do not result in the failure of the seal.

Drexler, R.L.

1990-10-17T23:59:59.000Z

60

Performance optimization of rotary dehumidifiers  

SciTech Connect

A rotary dehumidifier consists of a rotating porous matrix made of a desiccant with mechanically supporting materials. The dehumidification performance of a rotary dehumidifier wheel depends on its rotational speed, the sorption properties of the desiccant, the heat and mass transfer characteristics of the matrix, and the size of the dehumidifier. The effect of the rotational speed on the dehumidification performance of a rotary dehumidifier has been investigated by Zheng, Worek, and Novosel (1993). this paper extends that previous work and investigates the effects of desiccant sorption properties, the heat and mass transfer characteristics, and the size of the rotary dehumidifier on the dehumidification performance. The results show that the using desiccant materials in a rotary dehumidifier with different adsorption characteristics results in a wide variation in dehumidification performance. However, the maximum performance of a rotary dehumidifier occurs for a desiccant material having an isotherm shape that can be characterized to have a separation factor of 0.07. Also, as the desiccant moisture uptake increases, the dehumidifier performance also increases. However, the performance improvement for a desiccant matrix having a maximum moisture uptake of larger than 0.25 by weight is not significant. The heat and mass transfer properties and the size of rotary dehumidifier are characterized by the number of transfer units NTU. Generally, the larger the NTU, the better dehumidification performance. However, similar to the maximum moisture uptake, when the NTU is larger than 12, the performance will not improve significantly. Also, the dehumidifier with the most favorable adsorption characteristic has a slower rotational speed, which results in lower power requirements to rotate the desiccant wheel and smaller carry-over losses.

Zheng, W.; Worek, W.M. [Univ. of Chicago, IL (United States). Dept. of Mechanical Engineering; Novosel, D. [Gas Research Inst., Chicago, IL (United States)

1995-02-01T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Hoisting and Rigging: Pre-use Inspection Criteria for Below-the-Hook Lifting Devices, Slings, and Rigging  

E-Print Network (OSTI)

, and Rigging Hardware and Accessories URL: http://www-group.slac.stanford.edu/esh/eshmanual/references/hoistingHoisting and Rigging: Pre-use Inspection Criteria for Below-the-Hook Lifting Devices, Slings Department: Field Safety and Building Inspection Program: Hoisting and Rigging Authority: ESH Manual, Chapter

Wechsler, Risa H.

62

Test rig and particulate deposit and cleaning evaluation processes using the same  

DOE Patents (OSTI)

A rig and test program for determining the amount, if any, of contamination that will collect in the passages of a fluid flow system, such as a power plant fluid delivery system to equipment assemblies or sub-assemblies, and for establishing methods and processes for removing contamination therefrom. In the presently proposed embodiment, the rig and test programs are adapted in particular to utilize a high-pressure, high-volume water flush to remove contamination from substantially the entire fluid delivery system, both the quantity of contamination and as disposed or deposited within the system.

Schroder, Mark Stewart (Hendersonville, NC); Woodmansee, Donald Ernest (Schenectady, NY); Beadie, Douglas Frank (Greer, SC)

2002-01-01T23:59:59.000Z

63

Solar-heated rotary kiln  

DOE Patents (OSTI)

A solar heated rotary kiln utilized for decomposition of materials, such as zinc sulfate is disclosed. The rotary kiln has an open end and is enclosed in a sealed container having a window positioned for directing solar energy into the open end of the kiln. The material to be decomposed is directed through the container into the kiln by a feed tube. The container is also provided with an outlet for exhaust gases and an outlet for spent solids, and rests on a tiltable base. The window may be cooled and kept clear of debris by coolant gases.

Shell, P.K.

1982-04-14T23:59:59.000Z

64

Rotary actuator utilizing a shape memory alloy  

SciTech Connect

An apparatus is described comprising; (a) rotary accumulator means for accumulating a length of a shape memory alloy wire; (b) the shape memory alloy wire attached at one end to a point fixed with respect to the rotary accumulator means and attached at a second end to the rotary accumulator means; (c) biasing means for biasing the rotary accumulator means to a first position; and (d) means for heating the shape memory alloy wire to cause the shape memory alloy wire to contract, thereby rotating the rotary accumulator means from the first position to a second position.

Bloch, J.T.

1988-08-09T23:59:59.000Z

65

Surveillance Guide - CPS 8.1 Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING AND RIGGING HOISTING AND RIGGING 1.0 Objective The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used. The surveillance includes verification that hoisting and rigging work is performed in accordance with DOE requirements and best practices. 2.0 References 2.1 DOE O 440.1A, Worker Protection Management For Doe Federal And Contractor Employees 2.2 DOE-RL-92-36, Hanford Site Hoisting and Rigging Manual NOTE The DOE Hoisting and Rigging Manual should be used as the primary reference for this surveillance. 1 3.0 Requirements Implemented This surveillance is conducted to implement the RL Functions, Responsibilities, and Authorities Manual (FRAM) item No. 2504. 4.0 Surveillance Activities

66

NETL: News Release - DOE-Funded 'Microhole' Drilling Rig Demonstrated...  

NLE Websites -- All DOE Office Websites (Extended Search)

Rig Demonstrated Successfully in Midcontinent New Technology Initiative Slashes Drilling Costs, Benefits Environment, Energy Security WASHINGTON, DC - A U.S. Department of...

67

Optimization Online - Scheduling Workover Rigs for Onshore Oil ...  

E-Print Network (OSTI)

Oct 12, 2003 ... Scheduling Workover Rigs for Onshore Oil Production. Dario Aloise (dario ***at** * dimap.ufrn.br) Daniel Aloise (aloise ***at*** inf.puc-rio.br)

68

Field Demonstraton of Existing Microhole Coiled Tubing Rig (MCTR) Technology  

SciTech Connect

The performance of an advanced Microhole Coiled Tubing Rig (MCTR) has been measured in the field during the drilling of 25 test wells in the Niobrara formation of Western Kansas and Eastern Colorado. The coiled tubing (CT) rig designed, built and operated by Advanced Drilling Technologies (ADT), was documented in its performance by GTI staff in the course of drilling wells ranging in depth from 500 to nearly 3,000 feet. Access to well sites in the Niobrara for documenting CT rig performance was provided by Rosewood Resources of Arlington, VA. The ADT CT rig was selected for field performance evaluation because it is one of the most advanced commercial CT rig designs that demonstrate a high degree of process integration and ease of set-up and operation. Employing an information collection protocol, data was collected from the ADT CT rig during 25 drilling events that encompassed a wide range of depths and drilling conditions in the Niobrara. Information collected included time-function data, selected parametric information indicating CT rig operational conditions, staffing levels, and field observations of the CT rig in each phase of operation, from rig up to rig down. The data obtained in this field evaluation indicates that the ADT CT rig exhibited excellent performance in the drilling and completion of more than 25 wells in the Niobrara under varied drilling depths and formation conditions. In the majority of the 25 project well drilling events, ROP values ranged between 300 and 620 feet per hour. For all but the lowest 2 wells, ROP values averaged approximately 400 feet per hour, representing an excellent drilling capability. Most wells of depths between 500 and 2,000 feet were drilled at a total functional rig time of less than 16 hours; for wells as deep at 2,500 to 3,000 feet, the total rig time for the CT unit is usually well under one day. About 40-55 percent of the functional rig time is divided evenly between drilling and casing/cementing. The balance of time is divided among the remaining four functions of rig up/rig down, logging, lay down bottomhole assembly, and pick up bottomhole assembly. Observations made during all phases of CT rig operation at each of the project well installations have verified a number of characteristics of the technology that represent advantages that can produce significant savings of 25-35 percent per well. Attributes of the CT rig performance include: (1) Excellent hole quality with hole deviation amounting to 1-2 degrees; (2) Reduced need for auxiliary equipment; (3) Efficient rig mobilization requiring only four trailers; (4) Capability of ''Zero Discharge'' operation; (5) Improved safety; and, (6) Measurement while drilling capability. In addition, commercial cost data indicates that the CT rig reduces drilling costs by 25 to 35% compared to conventional drilling technology. Widespread commercial use of the Microhole Coiled Tubing technology in the United States for onshore Lower-48 drilling has the potential of achieving substantially positive impacts in terms of savings to the industry and resource expansion. Successfully commercialized Microhole CT Rig Technology is projected to achieve cumulative savings in Lower-48 onshore drilling expenditures of approximately 6.8 billion dollars by 2025. The reduced cost of CT microhole drilling is projected to enable the development of gas resources that would not have been economic with conventional methods. Because of the reduced cost of drilling achieved with CT rig technology, it is estimated that an additional 22 Tcf of gas resource will become economic to develop. In the future, the Microhole Coiled Tubing Rig represents an important platform for the continued improvement of drilling that draws on a new generation of various technologies to achieve goals of improved drilling cost and reduced impact to the environment.

Kent Perry; Samih Batarseh; Sheriff Gowelly; Thomas Hayes

2006-05-09T23:59:59.000Z

69

High bandwidth rotary fast tool servos and a hybrid rotary/linear electromagnetic actuator  

E-Print Network (OSTI)

This thesis describes the development of two high bandwidth short-stroke rotary fast tool servos and the hybrid rotary/linear electromagnetic actuator developed for one of them. Design insights, trade-off methodologies, ...

Montesanti, Richard Clement

2005-01-01T23:59:59.000Z

70

Rig upkeep vital in the downturn  

Science Conference Proceedings (OSTI)

As operations came to a close in 1982, many oil and gas contractors were facing the door of no return - subsequent years worsened matters. Drilling and workover units were returned to the lender and left stacked on and off location. Lending institutions began to weaken and, in some cases, collapse. However, many of the contractors with time and grade in providing contract drilling or workover services have had no desires or options other than to continue to operate in a downward spiraling market, much as they had done in the 50s and 60s. Operating under these circumstances requires a lot less flare and flame, and careful rearrangement of financial obligations. Contractors with equipment overloads reduced inventories and stacked the leftovers. This article shows that stacking or immobilizing a modern drilling rig or workover unit can be achieved economically. A sound preventive maintenance schedule can put the equipment on the stand-by board-ready to work. Several articles have been written on the ''new way to stack rigs.'' Most of these are simply a sensible realistic approach to maintaining a corporation's assets until they can be returned to the work force.

Leabo, J.H.

1987-05-01T23:59:59.000Z

71

C:\Documents and Settings\jhr\My Documents\C_drive\RIGS\users 2013\rigs_usersApril2013.vp  

Gasoline and Diesel Fuel Update (EIA)

23 23 Reserves Information Gathering System (RIGS) User's Guide Version 2013 For Report Year 2012 Energy Information Administration U.S. Department of Energy April 2013 Form EIA-23 Reserves Information Gathering System (RIGS) User's Guide April 2013 EIA-23 Reserves Information Gathering System (RIGS) User's Guide Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hardware / Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installing the RIGS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Using the EIA-23 Reserves Information Gathering System (RIGS) System . . . . . . . . . . . . . . . . . 4 Initial Data Import from Last Year's RIGS Submission File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The RIGS Main Menu Screen.

72

Design and construction of rigs for studying surface condensation and creating anodized metal oxide surfaces  

E-Print Network (OSTI)

This thesis details the design and construction of a rig for studying surface condensation and a rig for creating anodized metal oxides (AMOs). The condensation rig characterizes condensation for different surfaces; this ...

Sun, Wei-Yang

2011-01-01T23:59:59.000Z

73

Rotary kilns - transport phenomena and transport processes  

Science Conference Proceedings (OSTI)

Rotary kilns and rotating industrial drying ovens are used for a wide variety of applications including processing raw minerals and feedstocks as well as heat-treating hazardous wastes. They are particularly critical in the manufacture of Portland cement. Their design and operation is critical to their efficient usage, which if done incorrectly can result in improperly treated materials and excessive, high fuel costs. This book treats all engineering aspects of rotary kilns, including thermal and fluid principles involved in their operation, as well as how to properly design an engineering process that uses rotary kilns. Chapter 1: The Rotary Kiln Evolution and Phenomenon Chapter 2: Basic Description of Rotary Kiln Operation Chapter 3: Freeboard Aerodynamic Phenomena Chapter 4: Granular Flows in Rotary Kilns Chapter 5: Mixing and Segregation Chapter 6: Combustion and Flame - includes section on types of fuels used in rotary kilns, coal types, ranking and analysis, petroleum coke combustion, scrap tire combustion, pulverized fuel (coal/coke) firing in kilns, pulverized fuel delivery and firing systems. Chapter 7: Freeboard Heat Transfer Chapter 8: Heat Transfer Processes in the Rotary Kiln Bed Chapter 9: Mass and Energy Balance Chapter 10: Rotary Kiln Minerals Process Applications.

Boateng, A.

2008-01-15T23:59:59.000Z

74

Development of a portable grain mass flow sensor test rig  

Science Conference Proceedings (OSTI)

A portable grain mass flow sensor test rig was built to measure the accuracy of a mass flow sensor with dual use in the field as well as in the lab. Concurrently, a synchronization method was developed that employs GPS timing data to synchronize the ... Keywords: Mass flow sensor, Test rig, Yield monitor accuracy, Yield monitor error

M. Loghavi; R. Ehsani; R. Reeder

2008-05-01T23:59:59.000Z

75

Advanced Hot Section Materials and Coatings Test Rig  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principal activities during this reporting period were the continuation of test section detail design and developing specifications for auxiliary systems and facilities.

Dan Davies

2004-10-30T23:59:59.000Z

76

CRAD, Hoisting & Rigging Assessment Plan | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Plan Hoisting & Rigging Assessment Plan CRAD, Hoisting & Rigging Assessment Plan Performance Objective: To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001 Maintenance conducts safety inspections of hoisting and rigging equipment on a scheduled basis, certifying that safe operations are in

77

Advanced Hot Section Materials and Coatings Test Rig  

DOE Green Energy (OSTI)

Phase I of the Hyperbaric Advanced Hot Section Materials & Coating Test Rig Program has been successfully completed. Florida Turbine Technologies has designed and planned the implementation of a laboratory rig capable of simulating the hot gas path conditions of coal gas fired industrial gas turbine engines. Potential uses of this rig include investigations into environmental attack of turbine materials and coatings exposed to syngas, erosion, and thermal-mechanical fatigue. The principle activities during Phase 1 of this project included providing several conceptual designs for the test section, evaluating various syngas-fueled rig combustor concepts, comparing the various test section concepts and then selecting a configuration for detail design. Conceptual definition and requirements of auxiliary systems and facilities were also prepared. Implementation planning also progressed, with schedules prepared and future project milestones defined. The results of these tasks continue to show rig feasibility, both technically and economically.

Dan Davis

2006-09-30T23:59:59.000Z

78

Comparative analysis of core drilling and rotary drilling in volcanic terrane  

DOE Green Energy (OSTI)

Initially, the goal of this report is to compare and contrast penetration rates of rotary-mud drilling and core drilling in young volcanic terranes. It is widely recognized that areas containing an abundance of recent volcanic rocks are excellent targets for geothermal resources. Exploration programs depend heavily upon reliable subsurface information, because surface geophysical methods may be ineffective, inconclusive, or both. Past exploration drilling programs have mainly relied upon rotary-mud rigs for virtually all drilling activity. Core-drilling became popular several years ago, because it could deal effectively with two major problems encountered in young volcanic terranes: very hard, abrasive rock and extreme difficulty in controlling loss of circulation. In addition to overcoming these difficulties, core-drilling produced subsurface samples (core) that defined lithostratigraphy, structure and fractures far better than drill-chips. It seemed that the only negative aspect of core drilling was cost. The cost-per-foot may be two to three times higher than an ''initial quote'' for rotary drilling. In addition, penetration rates for comparable rock-types are often much lower for coring operations. This report also seeks to identify the extent of wireline core drilling (core-drilling using wireline retrieval) as a geothermal exploration tool. 25 refs., 21 figs., 13 tabs.

Flynn, T.; Trexler, D.T.; Wallace, R.H. Jr. (ed.)

1987-04-01T23:59:59.000Z

79

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

80

Hoisting & Rigging ISMS Assessment Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Objective: Assess the institutional and department/division hoisting and Objective: Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are involved in the

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11-i Chapter 11 11-i Chapter 11 Wire Rope and Slings CHAPTER 11 WIRE ROPE AND SLINGS This chapter provides requirements for the fabrication and use of wire rope and slings used in hoisting and rigging. 11.1 GENERAL ...............................................................................................................................11-1 11.2 WIRE ROPE ............................................................................................................................11-4 11.2.1 Wire-Rope Lays.........................................................................................................11-4 11.2.2 Wire-Rope Cores .......................................................................................................11-4 11.2.3 Wire Rope for General Purposes

82

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

83

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

5 5 HOSTILE ENVIRONMENTS 5-i Chapter 5 Hostile Environments This chapter describes provisions for hoisting and rigging operations in hostile work environments. 5.1 GENERAL ................................................................................................................................5-1 5.2 HOSTILE ENVIRONMENT PLAN ......................................................................................5-2 5.2.1 Marking and Posting ....................................................................................................5-2 5.2.2 Inspection and Testing .................................................................................................5-2 EXHIBIT I Hostile Environment Plan ............................................................................................5-3

84

Rotary union for use with ultrasonic thickness measuring probe  

DOE Patents (OSTI)

A rotary union for rotatably supporting an ultrasonic probe operable to nondestructively measure the thickness of steam generator tubes to determine the amount of corrosion experienced by the tubes includes a stationary body having a bore therethrough and an outlet drain, and a fitting rotatably mounted within the upper end of the body. The fitting has a bore aligned with the bore of the body. An electrical cable positioned within a water supply tube in an annular arrangement passes through the bore of the body and the bore of the fitting. This annular arrangement, in turn, is positioned within a connector element which extends outwardly from the fitting bore and is connected to the ultrasonic probe. An elastomeric lower bushing seals the annular arrangement to the lower end of the rotary union body and an elastomeric upper bushing seals the connector element to the fitting to permit the connector element and the ultrasonic probe connected thereto to rotate with the fitting relative to the body. The lower and upper bushings permit water to be passed through the annular arrangement and into the ultrasonic probe and thereafter discharged between the annular arrangement and the connector element to the outlet drain of the rotary union body. 5 figs.

Nachbar, H.D.

1992-09-15T23:59:59.000Z

85

Floating seal system for rotary devices  

DOE Patents (OSTI)

This invention relates to a floating seal system for rotary devices to reduce gas leakage around the rotary device in a duct and across the face of the rotary device to an adjacent duct. The peripheral seal bodies are made of resilient material having a generally U-shaped cross section wherein one of the legs is secured to a support member and the other of the legs forms a contacting seal against the rotary device. The legs of the peripheral seal form an extended angle of intersection of about 10.degree. to about 30.degree. in the unloaded condition to provide even sealing forces around the periphery of the rotary device. The peripheral seal extends around the periphery of the support member except where intersected by radial seals which reduce gas leakage across the face of the rotary device and between adjacent duct portions. The radial seal assembly is fabricated from channel bars, the smaller channel bar being secured to the divider of the support member and a larger inverted rigid floating channel bar having its legs freely movable over the legs of the smaller channel bar forming therewith a tubular channel. A resilient flexible tube is positioned within the tubular channel for substantially its full length to reduce gas leakage across the tubular channel. A spacer extends beyond the face of the floating channel near each end of the floating channel a distance to provide desired clearance between the floating channel and the face of the rotary device.

Banasiuk, Hubert A. (Chicago, IL)

1983-01-01T23:59:59.000Z

86

Floating seal system for rotary devices  

DOE Patents (OSTI)

This invention relates to a floating seal system for rotary devices to reduce gas leakage around the rotary device in a duct and across the face of the rotary device to an adjacent duct. The peripheral seal bodies are made of resilient material having a generally U-shaped cross section wherein one of the legs is secured to a support member and the other of the legs forms a contacting seal against the rotary device. The legs of the peripheral seal form an extended angle of intersection of about 10[degree] to about 30[degree] in the unloaded condition to provide even sealing forces around the periphery of the rotary device. The peripheral seal extends around the periphery of the support member except where intersected by radial seals which reduce gas leakage across the face of the rotary device and between adjacent duct portions. The radial seal assembly is fabricated from channel bars, the smaller channel bar being secured to the divider of the support member and a larger inverted rigid floating channel bar having its legs freely movable over the legs of the smaller channel bar forming therewith a tubular channel. A resilient flexible tube is positioned within the tubular channel for substantially its full length to reduce gas leakage across the tubular channel. A spacer extends beyond the face of the floating channel near each end of the floating channel a distance to provide desired clearance between the floating channel and the face of the rotary device. 5 figs.

Banasiuk, H.A.

1983-08-23T23:59:59.000Z

87

EIA-23L Reserves Information Gathering System (RIGS)  

Gasoline and Diesel Fuel Update (EIA)

EIA-23L Reserves Information Gathering System (RIGS) EIA-23L Reserves Information Gathering System (RIGS) Released: April 16, 2013 Background The Form EIA-23L, "Annual Survey of Domestic Oil and Gas Reserves, " is used to collect data on reserves of crude oil, natural gas, and natural gas liquids. These data are used to develop national and regional estimates of proved reserves of domestic crude oil, natural gas, and natural gas liquids, and to facilitate national energy policy decisions. Reporting on the Form EIA-23L is mandatory. Reserves Information Gathering System The Form EIA-23L Reserves Information Gathering System (RIGS), provides respondents with an efficient and effective means for filing the form using a personal computer (PC). Hardware / Software Requirements The minimum hardware requirements needed to install and use RIGS are:

88

Hoisting & Rigging Assessment Form | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Hoisting & Rigging Assessment Form Assess the institutional and department/division hoisting and rigging (including forklift, overhead cranes small hoists, and mobile cranes) requirements, policies, procedures, and work practices for both professional and incidental activities. Review the roles and responsibilities of line managers, support personnel and workers who are involved in these activities as well as the adequacy of compliance with institutional and/or Department/Division qualifications, training requirements, and inspection requirements. Assess the laboratory's process for understanding the causes and development of effective corrective actions for incidents/accidents. Review the roles and responsibilities of line managers, support personnel and workers who are

89

Guidelines for Using Synthetic Slings for Lifting and Rigging  

Science Conference Proceedings (OSTI)

"Guidelines for Using Synthetic Slings for Lifting and Rigging" provides nuclear and fossil maintenance personnel with information on the use of synthetic slings. This information will assist personnel in the identification, protection, and inspection of synthetic slings.

2003-02-10T23:59:59.000Z

90

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

91

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

TERMINOLOGY AND DEFINITIONS 1-1 Chapter 1 Terminology and Definitions The following are specialized terms commonly used when discussing hoisting and rigging operations. Many may not be used in this standard, but are included for general information. The terms are arranged in alphabetical order. Illustrations are included for clarity. ABRASION: Surface wear. ACCELERATION STRESS: Additional stress imposed due to increasing load velocity. ALTERNATE LAY: Lay of wire rope in which the strands are alternately regular and lang lay. ANSI: American National Standards Institute. APPOINTED: Assigned specific responsibilities by the employer or the employer's representative. AREA, METALLIC: Sum of the cross- sectional areas of individual wires in a wire rope

92

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A PROCUREMENT GUIDELINES A-1 Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

93

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPENDIX A APPENDIX A PROCUREMENT GUIDELINES A-i Appendix A Procurement Guidelines This appendix provides reference guidance in preparing purchase requisitions for hoisting and rigging materials and equipment. Nationally recognized standards and specifications are referenced for listed items. However, caution should be used prior to procurement of special items in order to verify appropriate specification or standard reference and requirements. Some specific requirements listed in this appendix are more restrictive than consensus standard requirements, but are recommended to ensure materials of adequate quality and workmanship are provided. Quality receipt inspections should be provided for all received materials in order to verify compliance of all

94

ADVANCED HOT SECTION MATERIALS AND COATINGS TEST RIG  

SciTech Connect

The Hyperbaric Advanced Hot Section Materials & Coating Test Rig program initiated this quarter, provides design and implementation of a laboratory rig capable of simulating the hot gas path conditions of coal-gas fired industrial gas turbine engines. The principle activity during this first reporting period were preparing for and conducting a project kick-off meeting, working through plans for the project implementation, and beginning the conceptual design of the test section.

Scott Reome; Dan Davies

2004-01-01T23:59:59.000Z

95

Enclosed rotary disc air pulser  

DOE Patents (OSTI)

An enclosed rotary disc air pulser for use with a solvent extraction pulse olumn includes a housing having inlet, exhaust and pulse leg ports, a shaft mounted in the housing and adapted for axial rotation therein, first and second disc members secured to the shaft within the housing in spaced relation to each other to define a chamber therebetween, the chamber being in communication with the pulse leg port, the first disc member located adjacent the inlet port, the second disc member being located adjacent the exhaust port, each disc member having a milled out portion, the disc members positioned on the shaft so that as the shaft rotates, the milled out portions permit alternative cyclical communication between the inlet port and the chamber and the exhaust port and the chamber.

Olson, A. L. (Idaho Falls, ID); Batcheller, Tom A. (Idaho Falls, ID); Rindfleisch, J. A. (Arco, ID); Morgan, John M. (Arco, ID)

1989-01-01T23:59:59.000Z

96

Enclosed rotary disc air pulser  

DOE Patents (OSTI)

This invention is comprised of an enclosed rotary disc air pulser for use with a solvent extraction pulse column includes a housing having inlet, exhaust and pulse leg ports, a shaft mounted in the housing and adapted for axial rotation therein, first and second disc members secured to the shaft within the housing in spaced relation to each other to define a chamber there between, the chamber being in communication with the pulse leg port, and first disc member located adjacent the inlet port, the second disc member being located adjacent the exhaust port, each disc member having a milled out portion, the disc members positioned on the shaft so that as the shaft rotates, the milled out portions permit alternative cyclical communication between the inlet port and the chamber and the exhaust port and chamber. 5 figs.

Olson, A.L.; Batcheller, T.A.; Rindfleisch, J.A.; Morgan, J.M.

1988-08-12T23:59:59.000Z

97

Experimental Results on Advanced Rotary Desiccant Dehumidifiers  

E-Print Network (OSTI)

The Solar Energy Research Institute (SERI) has developed the Cyclic Test Facility (CTF) to develop and validate analytical methods for evaluating and predicting the performance of advanced rotary dehumidifiers. This paper describes the CTF, the dehumidifiers tested at the CTF, and the analytical methods used. The results reported provide an engineering data base and a design tool for evaluating rotary dehumidifiers for desiccant cooling applications.

Barathan, D.; Parsons, J. M.; MaClaine-Cross, I.

1986-01-01T23:59:59.000Z

98

Experimental results on advanced rotary desiccant dehumidifiers  

DOE Green Energy (OSTI)

The Solar Energy Research Institute (SERI) has developed the Cyclic Test Facility (CTF) to develop and validate analytical methods for evaluating and predicting the performance of advanced rotary dehumidifiers. This paper describes the CTF, the dehumidifiers tested at the CTF, and the analytical methods used. The results reported provide an engineering data base and a design tool for evaluating rotary dehumidifiers for desiccant cooling applications.

Bharathan, D.; Parsons, J.; Maclaine-cross, I.

1986-08-01T23:59:59.000Z

99

Structural Insights into RNA Recognition by RIG-I  

Science Conference Proceedings (OSTI)

Intracellular RIG-I-like receptors (RLRs, including RIG-I, MDA-5, and LGP2) recognize viral RNAs as pathogen-associated molecular patterns (PAMPs) and initiate an antiviral immune response. To understand the molecular basis of this process, we determined the crystal structure of RIG-I in complex with double-stranded RNA (dsRNA). The dsRNA is sheathed within a network of protein domains that include a conserved 'helicase' domain (regions HEL1 and HEL2), a specialized insertion domain (HEL2i), and a C-terminal regulatory domain (CTD). A V-shaped pincer connects HEL2 and the CTD by gripping an {alpha}-helical shaft that extends from HEL1. In this way, the pincer coordinates functions of all the domains and couples RNA binding with ATP hydrolysis. RIG-I falls within the Dicer-RIG-I clade of the superfamily 2 helicases, and this structure reveals complex interplay between motor domains, accessory mechanical domains, and RNA that has implications for understanding the nanomechanical function of this protein family and other ATPases more broadly.

Luo, Dahai; Ding, Steve C.; Vela, Adriana; Kohlway, Andrew; Lindenbach, Brett D.; Pyle, Anna Marie (Yale)

2011-10-27T23:59:59.000Z

100

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 BELOW-THE-HOOK LIFTING DEVICES 14-i Chapter 14 Below-the-Hook Lifting Devices This chapter provides the requirements for below-the-hook lifting devices used in hoisting and rigging, such as spreader bars, lifting yokes, and lift fixtures. This section implements the requirements of ASME B30.20, "Below-the-Hook Lifting Devices." NOTE: Special lifting devices for shipping containers weighing 10,000 lb or more that are used for radioactive materials may be governed by ANSI N14.6 ["Standard for Special Lifting Devices for Shipping Containers Weighing 10,000 Pounds (4,500 kg) or More for Nuclear Materials."] 14.1 GENERAL ...............................................................................................................................14-1

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Coal desulfurization in a rotary kiln combustor  

Science Conference Proceedings (OSTI)

The purpose of this project was to demonstrate the combustion of coal and coal wastes in a rotary kiln reactor with limestone addition for sulfur control. The rationale for the project was the perception that rotary systems could bring several advantages to combustion of these fuels, and may thus offer an alternative to fluid-bed boilers. Towards this end, an existing wood pyrolysis kiln (the Humphrey Charcoal kiln) was to be suitably refurbished and retrofitted with a specially designed version of a patented air distributor provided by Universal Energy, Inc. (UEI). As the project progressed beyond the initial stages, a number of issues were raised regarding the feasibility and the possible advantages of burning coals in a rotary kiln combustor and, in particular, the suitability of the Humphrey Charcoal kiln as a combustor. Instead, an opportunity arose to conduct combustion tests in the PEDCO Rotary Cascading-Bed Boiler (RCBB) commercial demonstration unit at the North American Rayon CO. (NARCO) in Elizabethton, TN. The tests focused on anthracite culm and had two objectives: (a) determine the feasibility of burning anthracite culms in a rotary kiln boiler and (b) obtain input for any further work involving the Humphrey Charcoal kiln combustor. A number of tests were conducted at the PEDCO unit. The last one was conducted on anthracite culm procured directly from the feed bin of a commercial circulating fluid-bed boiler. The results were disappointing; it was difficult to maintain sustained combustion even when large quantities of supplemental fuel were used. Combustion efficiency was poor, around 60 percent. The results suggest that the rotary kiln boiler, as designed, is ill-suited with respect to low-grade, hard to burn solid fuels, such as anthracite culm. Indeed, data from combustion of bituminous coal in the PEDCO unit suggest that with respect to coal in general, the rotary kiln boiler appears inferior to the circulating fluid bed boiler.

Cobb, J.T. Jr.

1992-09-11T23:59:59.000Z

102

Natural Gas for the Long Haul (Big Rigs Go Green)  

NLE Websites -- All DOE Office Websites (Extended Search)

the Long Haul (Big Rigs Go Green) the Long Haul (Big Rigs Go Green) JOHN DAVIS: No one has been hit harder by rising fuel prices than America's long-haul commercial truckers. A big rig can easily burn 20,000 gallons of fuel a year, and with diesel prices projected to keep rising, this not only pinches the trucker's bottom line, but that extra cost is passed on to American consumers. Meanwhile, natural gas prices have remained stable and are forecast to stay that way for years to come. Up to now, demand for natural gas as a transportation fuel has been mostly for compressed natural gas used by light and medium-duty vehicles. City buses, refuse haulers, utilities, and

103

Inventory management of steel plates at an oil rig construction company  

E-Print Network (OSTI)

Keppel Fels produces make-to-order oil exploration rigs for the global market. Each rig requires close to 6000 metric tons of steel in the course of its production. Optimal management of this steel is very critical in this ...

Tan, Chien Yung

2006-01-01T23:59:59.000Z

104

Mixed Stream Test Rig Winter FY-2011 Report  

SciTech Connect

This report describes the data and analysis of the initial testing campaign of the Mixed Stream Test Rig (MISTER) at Idaho National Laboratory (INL). It describes the test specimen selection, physical configuration of the test equipment, operations methodology, and data and analysis of specimens exposed in two environments designed to represent those expected for high temperature steam electrolysis (HTSE).

Chalres Park; Tedd Lister; Kevin DeWall

2011-04-01T23:59:59.000Z

105

Diesel Rig Mechanical Peaking System Based on Flywheel Storage Technolgy  

Science Conference Proceedings (OSTI)

Flywheel energy storage technology is an emerging energy storage technology, there is a great development in recent years promising energy storage technology, with a large energy storage, high power, no pollution, use of broad, simple maintenance, enabling ... Keywords: Flywheel energy storage technology, mechanical peaking, diesel rig, peak motor

Shuguang Liu, Jia Wang

2012-07-01T23:59:59.000Z

106

Power Production from Geothermal Brine with the Rotary Separator Turbine  

SciTech Connect

The rotary separator turbine is a new turbine device that operates with gas-liquid mixtures. This device achieves complete gas-liquid separation, generates power from the liquid and repressurizes the liquid. The use of the rotary separator turbine for geothermal power generation was investigated on this program. A pilot scale unit was designed and tested. Tests were conducted with a clean water/steam mixture and with geothermal brine/steam flows at East Mesa, California; Raft River, Idaho; and Roosevelt Hot Springs, Utah. The test results were used to calculate the performance advantage of a rotary separator turbine power system compared to a flash steam power system and a binary power system. The calculated performance advantages were then used to estimate market potential for wellhead and central station Biphase units. The measured performance in the laboratory and in the field agreed to within {+-} 10% of the predicted values. The design goal of 20 kWe was generated both in the laboratory and from brine. Separated steam quality was measured to be greater than 99.96% at all three geothermal resources and in the laboratory. Brine pressure leaving the test unit was greater than reinjection pressure requirements. Maximum brine outlet pressure of 90 psig was demonstrated. The measured performance values would result in a 34% increase in electric power production above a single stage flash steam system. Increasing the size from the pilot size unit (20kWe) to a wellhead unit (2000 kWe) gave a calculated performance advantage of 40%. Based on these favorable results, design, construction and testing of a full-size well-head unit was initiated.

Cerini, Donald J.; Hays, Lance G.

1980-12-01T23:59:59.000Z

107

Planning and scheduling a fleet of rigs using simulation-optimization  

Science Conference Proceedings (OSTI)

Some of the most important and expensive activities in the oil field development and production phases relate to using rigs. These can be used for drilling wells, or for maintenance activities. As rigs are usually scarce compared to the number of wells ... Keywords: Planning, Rigs, Scheduling, Simulation-optimization

Hugo ViníCius Bassi; VirgíLio Jose Martins Ferreira Filho; Laura Bahiense

2012-12-01T23:59:59.000Z

108

Drill Rig Safety Topics of the Presentation  

E-Print Network (OSTI)

· Check oil level daily -engine oil & coolant -compressor air/oil tank -hydraulic tank -pump oil (water injection, mud, etc.) -pump drive gearboxes · Grease daily (must purge dirt) ­ Floating Sub ­ Rollers ­ Air · Fuel and Oil Leaks · Hose Leaks and Failures · Electrical · Smoking #12;Schramm Electrical Safety

109

Department of Energy Supercomputer Helps Design More Efficient Big Rigs |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department of Energy Supercomputer Helps Design More Efficient Big Department of Energy Supercomputer Helps Design More Efficient Big Rigs Department of Energy Supercomputer Helps Design More Efficient Big Rigs February 8, 2011 - 12:00am Addthis Washington, DC - BMI Corporation, a company in South Carolina, in partnership with the Department of Energy's Oak Ridge National Laboratory (ORNL) has successfully developed a technology that will make semi trucks more fuel efficient with the potential to save millions of gallons of fuel. Utilizing the nation's most powerful computer, BMI Corp designed a SmartTruck UnderTray System, a set of integrated aerodynamic fairings that improve the aerodynamics of 18-wheeler (Class 8) long-haul trucks. If all 1.3 million Class 8 trucks in the U.S. were configured with these components, companies could achieve annual savings of 1.5 billion gallons

110

BACKPRESSURE TESTING OF ROTARY MICROFILTER DISKS  

Science Conference Proceedings (OSTI)

The Savannah River National Laboratory (SRNL), under the Department of Energy (DOE) Office of Environmental Management (EM), is modifying and testing the SpinTek{trademark} rotary microfilter (RMF) for radioactive filtration service in the Department of Energy (DOE) complex. The RMF has been shown to improve filtration throughput when compared to other conventional methods such as cross-flow filtration. A concern with the RMF was that backpressure, or reverse flow through the disk, would damage the filter membranes. Reverse flow might happen as a result of an inadvertent valve alignment during flushing. Testing was completed in the Engineering Development Laboratory (EDL) located in SRNL to study the physical effects of backpressure as well as to determine the maximum allowable back-pressure for RMF disks. The RMF disks tested at the EDL were manufactured by SpinTek{trademark} Filtration and used a Pall Corporation PMM050 filter membrane (0.5 micron nominal pore size) made from 316L stainless steel. Early versions of the RMF disks were made from synthetic materials that were incompatible with caustic solutions and radioactive service as well as being susceptible to delaminating when subjected to backpressure. Figure 1-1 shows the essential components of the RMF; 3 rotating disks and 3 stationary turbulence promoters (or shear elements) are shown. Figure 1-2 show the assembly view of a 25 disk RMF proposed for use at the Savannah River Site (SRS) and at the Hanford Facility. The purpose of the testing discussed in this report was to determine the allowable backpressure for RMF disks as well as study the physical effects of backpressure on RMF disks made with the Pall PMM050 membrane. This was accomplished by pressurizing the disks in the reverse flow direction (backpressure) until the test limit was reached or until membrane failure occurred. Backpressure was applied to the disks with air while submerged in deionized (DI) water. This method provided a visual representation of membrane integrity via bubble flow patterns. Membrane failure was defined as the inability to filter effectively at the nominal filter pore size. Effective filtration was determined by turbidity measurements of filtrate that was produced by applying forward-pressure to the disks while submerged in a representative simulant. The representative simulant was Tank 8F simulated sludge produced for SRNL by Optima Chemical. Two disks were tested. Disk 1 was tested primarily to determine approximate levels of backpressure where membrane failure occurred. These levels were then used to define the strategy for testing the Disk 2; a strategy that would better define and quantify the mode of failure.

Fowley, M.; Herman, D.

2011-04-14T23:59:59.000Z

111

Compact fast analyzer of rotary cuvette type  

DOE Patents (OSTI)

A compact fast analyzer of the rotary cuvette type is provided for simultaneously determining concentrations in a multiplicity of discrete samples using either absorbance or fluorescence measurement techniques. A rigid, generally rectangular frame defines optical passageways for the absorbance and fluorescence measurement systems. The frame also serves as a mounting structure for various optical components as well as for the cuvette rotor mount and drive system. A single light source and photodetector are used in making both absorbance and fluorescence measurements. Rotor removal and insertion are facilitated by a swing-out drive motor and rotor mount. BACKGROUND OF THE INVENTION The invention relates generally to concentration measuring instruments and more specifically to a compact fast analyzer of the rotary cuvette type which is suitable for making either absorbance or fluorescence measurements. It was made in the course of, or under, a contract with the U.S. Atomic Energy Commission.

Thacker, Louis H. (Knoxville, TN)

1976-01-01T23:59:59.000Z

112

Rotary Mode Core Sample System availability improvement  

SciTech Connect

The Rotary Mode Core Sample System (RMCSS) is used to obtain stratified samples of the waste deposits in single-shell and double-shell waste tanks at the Hanford Site. The samples are used to characterize the waste in support of ongoing and future waste remediation efforts. Four sampling trucks have been developed to obtain these samples. Truck I was the first in operation and is currently being used to obtain samples where the push mode is appropriate (i.e., no rotation of drill). Truck 2 is similar to truck 1, except for added safety features, and is in operation to obtain samples using either a push mode or rotary drill mode. Trucks 3 and 4 are now being fabricated to be essentially identical to truck 2.

Jenkins, W.W.; Bennett, K.L.; Potter, J.D. [Westinghouse Hanford Co., Richland, WA (United States); Cross, B.T.; Burkes, J.M.; Rogers, A.C. [Southwest Research Institute (United States)

1995-02-28T23:59:59.000Z

113

High Pressure Rotary Shaft Sealing Mechanism  

DOE Patents (OSTI)

A laterally translatable pressure staged rotary shaft sealing mechanism having a seal housing with a shaft passage therein being exposed to a fluid pressure P1 and with a rotary shaft being located within the shaft passage. At least one annular laterally translatable seal carrier is provided. First and second annular resilient sealing elements are supported in axially spaced relation by the annular seal carriers and have sealing relation with the rotary shaft. The seal housing and at least one seal carrier define a first pressure staging chamber exposed to the first annular resilient sealing element and a second pressure staging chamber located between and exposed to the first and second annular resilient sealing elements. A first fluid is circulated to the first pressure chamber at a pressure P1, and a second staging pressure fluid is circulated to the second pressure chamber at a fraction of pressure P1 to achieve pressure staging, cooling of the seals. Seal placement provides hydraulic force balancing of the annular seal carriers.

Dietle, Lannie (Sugar Land, TX); Gobeli, Jeffrey D. (Houston, TX)

2001-05-08T23:59:59.000Z

114

Coal desulfurization in a rotary kiln combustor  

Science Conference Proceedings (OSTI)

BCR National Laboratory (BCRNL) has initiated a project aimed at evaluating the technical and economic feasibility of using a rotary kiln, suitably modified, to burn Pennsylvania anthracite wastes, co-fired with high-sulfur bituminous coal. Limestone will be injected into the kiln for sulfur control, to determine whether high sulfur capture levels can be achieved with high sorbent utilization. The principal objectives of this work are: (1) to prove the feasibility of burning anthracite refuse, with co-firing of high-sulfur bituminous coal and with limestone injection for sulfur emissions control, in a rotary kiln fitted with a Universal Energy International (UEI) air injector system; (2) to determine the emissions levels of SO{sub x} and NO{sub x} and specifically to identify the Ca/S ratios that are required to meet New Source Performance Standards; (3) to evaluate the technical and economic merits of a commercial rotary kiln combustor in comparison to fluidized bed combustors; and, (4) to ascertain the need for further work, including additional combustion tests, prior to commercial application, and to recommend accordingly a detailed program towards this end.

Cobb, J.T. Jr.

1990-08-15T23:59:59.000Z

115

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on...

116

A unidirectional rotary solenoid as applied to stronglinks  

Science Conference Proceedings (OSTI)

This paper describes the design goals and results of an advanced development stronglink project with special emphasis on a new rotary solenoid concept. 10 figs.

Kenderdine, E.W.

1988-01-01T23:59:59.000Z

117

Rig count in Utica Shale doubles from year ago - Today in ...  

U.S. Energy Information Administration (EIA)

The number of active oil and natural gas rigs in the Appalachian Basin's Utica Shale formation for the last week of October 2012 (ending October 26) ...

118

CPS 8.1 Hoisting and Rigging, 2/25/2000  

Energy.gov (U.S. Department of Energy (DOE))

The objective of this surveillance is to examine hoisting and rigging operations to ensure that safe equipment and work practices are being used.  The surveillance includes verification that...

119

Design, Construction, and Preliminary Validation of the Turbine Reacting Flow Rig.  

E-Print Network (OSTI)

??This thesis presents the design, construction and partial operation of the Turbine Reacting Flow Rig (TuRFR), which is a high temperature turbine vane test facility… (more)

Cramer, Klaron Nathanael

2009-01-01T23:59:59.000Z

120

Slant rigs offer big payoffs in shallow drilling  

Science Conference Proceedings (OSTI)

Slant hole drilling technology can result in considerable savings over conventionally drilled deviated holes because mud motors and deviation control with measurement while drilling tools are usually unnecessary. The benefits of using slant hole rigs for development drilling improve after the bit walk tendencies and the correct bottom hole assemblies have been determined for a particular area. This article discusses three recent drilling operations that successfully used slant drilling technology on land-based projects: drilling for heavy oil in Alberta, drilling for gas in Alberta, and drilling a river crossing for a gas pipeline in British Columbia. These examples demonstrate the flexibility of slant drilling technology.

Smith, J. (George E. Failing Co., Enid, OK (US)); Edwards, B. (Sierra Drilling Co., Calgary (CA))

1992-03-30T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

TESTING OF THE SECOND GENERATION SPINTEK ROTARY FILTER -11357  

SciTech Connect

The SpinTek rotary microfilter has been developed under the Department of Energy (DOE) Office of Environmental Management (EM) for the purpose of deployment in radioactive service in the DOE complex. The unit that was fabricated and tested is the second generation of the filter that incorporates recommended improvements from previous testing. The completion of this test satisfied a key milestone for the EM technology development program and technology readiness for deployment by Savannah River Remediation in the Small Column Ion Exchange and Sludge Washing processes at the Savannah River Site (SRS). The Savannah River National Laboratory (SRNL) contracted SpinTek Filtration to fabricate a full scale 25 disk rotary filter and perform a 1000 hour endurance test with a simulated SRS sludge. Over 1500 hours of operation have been completed with the filter. SpinTek Filtration fabricated a prototypic 25 disk rotary filter including updates to manufacturing tolerances, an updated design to the rotary joint, improved cooling to the bottom journal, decreases in disk and filter shaft hydraulic resistances. The filter disks were fabricated with 0.5 {micro} pore size, sintered-metal filter media manufactured by Pall Corporation (M050). After fabrication was complete, the filter passed acceptance tests demonstrating rejection of solids and clean water flux with a 50% improvement over the previous filters. Once the acceptance test was complete, a 1000 hour endurance test was initiated simulating a sludge washing process. The test used a simulated SRS Sludge Batch 6 recipe. The insoluble solids started at 5 wt% and were raised to 10 and 15 wt% insoluble solids to simulate the concentration of a large volume tank. The filter system was automated and set up for 24 hour unattended operation. To facilitate this, process control logic was written to operate the filter. During the development it was demonstrated that the method of starting and stopping the filter can affect the build up of filter cake on the disks and therefore the performance of the filter. The filter performed well with the simulant. Very little drop in production was noticed between the 5 and 10 wt% insoluble solids feed. Increasing to 15 wt% had a more pronounced impact due to the rheology of the feed. Acid cleaning was used to clean the filter disks in-situ and restore filtration rate to almost 90% of the initial clean disk rate. Eighty liters of 0.2 M nitric acid in conjunction with water rinses were used to clean the filter in less than 2 hours. Filter testing was completed after 1000 hours of operation were performed on the final filter assembly configuration. The total run time for the testing was over 1500 hours. At the end of the test, the sludge washing was performed successfully from approximately 5.6 M to less than 1 M sodium.

Herman, D.; Poirier, M.; Fowley, M.; Keefer, M.; Huff, T.

2011-02-02T23:59:59.000Z

122

Technical and economic evaluation of selected compact drill rigs for drilling 10,000 foot geothermal production wells  

DOE Green Energy (OSTI)

This report summarizes the investigation and evaluation of several {open_quotes}compact{close_quotes} drill rigs which could be used for drilling geothermal production wells. Use of these smaller rigs would save money by reducing mobilization costs, fuel consumption, crew sizes, and environmental impact. Advantages and disadvantages of currently-manufactured rigs are identified, and desirable characteristics for the {open_quotes}ideal{close_quotes} compact rig are defined. The report includes a detailed cost estimate of a specific rig, and an evaluation of the cost/benefit ratio of using this rig. Industry contacts for further information are given.

Huttrer, G.W. [Geothermal Management Company, Inc., Frisco, CO (United States)

1997-11-01T23:59:59.000Z

123

Demonstration of a rotary separator for two-phase brine and steam flows. Final report  

DOE Green Energy (OSTI)

The application of a two-phase rotary separator for geothermal energy conversion was demonstrated. Laboratory tests were conducted with clean water and steam at Biphase Energy Systems, Inc., Santa Monica, California. Field tests were conducted at the Union Oil Co., Tow No. 1 wellsite near Brawley, California. The system tested consisted of the major components of a total flow rotary separator/turbine conversion system. A nozzle converted the brine wellhead enthalpy to two-phase flow kinetic by impinging the nozzle flow tangentially on the inside of the separator. The flow was therefore subjected to the high centrifugal force field in the separator. This caused the liquid phase to collect as a film on the separator drum with very little energy loss. The steam was allowed to flow radially inward to the central steam discharge. Potable water was obtained by condensing the steam exhaust. The brine collection system converted the liquid film kinetic energy to static pressure head. The system was operated for 116 hours in a high salinity environment (115,000 ppM TDS). The system operated properly with no adverse effects from solids precipitation or scale buildup. The rotary separator produced separate flows of pure liquid and steam of greater than 99.5% quality.

Cerini, D.J.

1978-01-01T23:59:59.000Z

124

Coal desulfurization in a rotary kiln combustor  

Science Conference Proceedings (OSTI)

Several issues that could have an impact on the capability to burn anthracite culm in a rotary bed boiler were identified; specifically, questions were raised concerning the specifications of the anthracite culm itself and some relating to the equipment. The anthracite culm delivered was wet, (with more than 10 percent moisture), and coarser than feed material for fluidized boilers. It was felt that using finer fuel, ensuring that it is largely dry, would aid the combustion of anthracite culm. It also appeared that if provisions were made for more efficient internal and external recycle of ash, this would also enhance the combustion of this fuel. Accordingly, the decision was made to conduct an additional campaign of tests that would incorporate these changes. The tests, conducted on July 15 and 16, 1991, involved an anthracite culm that was, in fact, obtained from a fluidized bed a heating value of 3,000 Btu/lb and came with a top size of 1/4-inch. Despite these changes, sustained combustion could not be achieved without the use of large quantities of supplemental fuel. Based on these tests, we tend to conclude that the rotary kiln is ill suited for the combustion of hard-to-burn, low-grade solid fuels like anthracite culm.

Cobb, J.T. Jr.

1991-08-29T23:59:59.000Z

125

A Testing and Controlling System for the Combustion Test Rig of Gas Turbine Combustor  

Science Conference Proceedings (OSTI)

In this paper, a testing and controlling system is designed for the test rig of gas turbine combustor by using VXi bus and PLC technology. The system is composed of two subsystems: the data acquisition subsystem and the control subsystem. The data acquisition ... Keywords: combustion test rig, VXi bus, PLC control, Modbus agreement, data acquisition

Nihui Xie; Hua Song; Hongzhuan Qiu

2011-10-01T23:59:59.000Z

126

Affine crystal structure on rigged configurations of type $D_{n}^{(1)}$  

Science Conference Proceedings (OSTI)

Extending the work in Schilling (Int. Math. Res. Not. 2006:97376, 2006), we introduce the affine crystal action on rigged configurations which is isomorphic to the Kirillov---Reshetikhin crystal B r,s of type Keywords: Crystal bases, Quantum algebras, Rigged configurations

Masato Okado; Reiho Sakamoto; Anne Schilling

2013-05-01T23:59:59.000Z

127

The Application Research of AC Frequency Conversion Technique in Transmission Control System of Oil Rig  

Science Conference Proceedings (OSTI)

This paper mainly introduced the basic structure and work principle of transmission agent on electric drilling rig, meanwhile the frequency control and parallel operation of motors used in the transmission agent were analyzed and designed. Using parallel ... Keywords: Rig, Transmission, Frequency control, Parallel Operation Control

Ruifan Yang; Yong Peng

2010-03-01T23:59:59.000Z

128

Probabilistic structure matching for visual SLAM with a multi-camera rig  

Science Conference Proceedings (OSTI)

We propose to use a multi-camera rig for simultaneous localization and mapping (SLAM), providing flexibility in sensor placement on mobile robot platforms while exploiting the stronger localization constraints provided by omni-directional sensors. In ... Keywords: Localization, Mapping, Mobile robot, Multi-camera rig, Omni-directional, SFM

Michael Kaess; Frank Dellaert

2010-02-01T23:59:59.000Z

129

Use power factor correction to cut SCR rig fuel bills  

SciTech Connect

When drilling with SCR-powered drilling rigs, there are specific instances on every well when the kVA capacity of the AC generators prohibits efficient engine loading. It then becomes necessary to run another engine-generator set to provide sufficient kVA to power the load, even though the kW required by the load can be furnished by existing engine(s) on line. The practice of running one more engine than can be fully loaded causes all engines on line to run at a less efficient point on the brake specific fuel consumption curve (BSFC) and therefore costs more in terms of engine hours, fuel and maintenance costs. This article presents a study of the load represented by the mud pump and drawworks along with a graphical representation that shows the effect of these loads on the engine generator system both with and without a power factor correction device.

Logan, R.T.

1983-09-01T23:59:59.000Z

130

Results of the 1000 Hour Rotary Microfilter Endurance Test  

Stellite on Nitronic 60. 8 SRNL-L3100-2010-00229 Rotary Microfilter 1000 Hour Test Flux Data for 1000 Hour Test 0 1 2 3 4 5 6 0 100 200 300 400 500 ...

131

TESTING OF THE DUAL ROTARY FILTER SYSTEM  

SciTech Connect

The Savannah River National Laboratory (SRNL) installed and tested two hydraulically connected SpinTek rotary microfilter (RMF) units to determine the behavior of a multiple filter system. Both units were successfully controlled by a control scheme written in DELTA-V architecture by Savannah River Remediation (SRR) Process Control Engineering personnel. The control system was tuned to provide satisfactory response to changing conditions during the operation of the multi-filter system. Stability was maintained through the startup and shutdown of one of the filter units while the second was still in operation. The installation configuration originally proposed by the Small Colum Ion Exchange (SCIX) project of independent filter and motor mountings may be susceptible to vibration. Significant stiffening of the filter and motor mounts was required to minimize the vibration. Alignment of the motor to the filter was a challenge in this test configuration. The deployment configuration must be easy to manipulate and allow for fine adjustment. An analysis of the vibration signature of the test system identified critical speeds. Whether it corresponds to the resonance frequency of a rotor radial vibration mode that was excited by rotor unbalance is uncertain based upon the measurements. A relative motion series should be completed on the filter with the final shaft configuration to determine if the resonances exist in the final filter design. The instrumentation selected for deployment, including the concentrate discharge control valve and flow meters, performed well. Automation of the valve control integrated well with the control scheme and when used in concert with the other control variables, allowed automated control of the dual RMF system. The one area of concern with the instrumentation was the condition resulting when the filtrate flow meter operated with less than three gpm. This low flow was at the lower range of performance for the flow meter. This should not be an issue in deployment where the desired flow rate will be within the normal operating range of the meter. Testing demonstrated that the use of a flexible line for the filtrate discharge is highly desired at the outlet of the rotary union to transition to the system piping. Isolating the vibration from the rotary union will significantly improve the lifetime of the seals. Methods to monitor and isolate individual filters should be considered during deployment. The ability to diagnose issues and isolate individual filters would allow isolation prior to failure. Thus, filters may be cleaned or repaired instead of requiring complete replacement if the condition were to continue unnoticed. Isolating the filtrate line of each filter during startup will minimize the premature buildup of solids on the filter disks. Several tests have shown that the method of filter startup can improve performance lifetime of the filters. The installation must factor in an air inlet for the draining of a filter that does not involve a reverse flow through the filter disks. The reverse flow may cause deformation of the disks or may damage other components of the filters themselves.

Herman, D.; Fowley, M.; Stefanko, D.

2011-08-29T23:59:59.000Z

132

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division HOISTING & RIGGING Assessment Plan--NNSA/Nevada Site Office Facility Representative Division : To determine that hoisting and rigging operations are conducted according to "industry best standards" for increasing equipment reliability while assuring worker safety, and to verify issues being addressed in BN Hoisting assessment. Criteria: Lifts are identified and categorized appropriately for scheduled maintenance. DOE-STD-1090-2001 An integrated process ensures safety issues are identified and controls established. DOE-STD-1090-2001 Personnel operating and maintaining the hoisting equipment are trained; they understand their roles and responsibilities. DOE-STD-1090-2001

133

Nucleotide sequences and modifications that determine RIG-I/RNA binding and signaling activities  

E-Print Network (OSTI)

Cytoplasmic viral RNAs with 5? triphosphates (5?ppp) are detected by the RNA helicase RIG-I, initiating downstream signaling and alpha/beta interferon (IFN-?/?) expression that establish an antiviral state. We demonstrate ...

Urzi, Dina

134

Calibration and performance of a selective catalytic reduction (SCR) bench rig for NOx? emissions control  

E-Print Network (OSTI)

A laboratory test rig was designed and built to easily test SCR (Selective Catalytic Reduction) technology. Equipped with three 6 kW heaters, connections for liquid N2 and an assortment of test gases, and a connection with ...

Castro Galnares, Sebastián (Castro Galnares Wright Paz)

2008-01-01T23:59:59.000Z

135

U.S. Crude Oil and Natural Gas Active Well Service Rigs in ...  

U.S. Energy Information Administration (EIA)

U.S. Crude Oil and Natural Gas Active Well Service Rigs in operation (Number of Elements) Decade Year-0 Year-1 Year-2 Year-3 Year-4 Year-5 Year-6 Year-7 Year-8 Year-9;

136

Structural basis of RNA recognition and activation by innate immune receptor RIG-I  

Science Conference Proceedings (OSTI)

Retinoic-acid-inducible gene-I (RIG-I; also known as DDX58) is a cytoplasmic pathogen recognition receptor that recognizes pathogen-associated molecular pattern (PAMP) motifs to differentiate between viral and cellular RNAs. RIG-I is activated by blunt-ended double-stranded (ds)RNA with or without a 5'-triphosphate (ppp), by single-stranded RNA marked by a 5'-ppp and by polyuridine sequences. Upon binding to such PAMP motifs, RIG-I initiates a signalling cascade that induces innate immune defences and inflammatory cytokines to establish an antiviral state. The RIG-I pathway is highly regulated and aberrant signalling leads to apoptosis, altered cell differentiation, inflammation, autoimmune diseases and cancer. The helicase and repressor domains (RD) of RIG-I recognize dsRNA and 5'-ppp RNA to activate the two amino-terminal caspase recruitment domains (CARDs) for signalling. Here, to understand the synergy between the helicase and the RD for RNA binding, and the contribution of ATP hydrolysis to RIG-I activation, we determined the structure of human RIG-I helicase-RD in complex with dsRNA and an ATP analogue. The helicase-RD organizes into a ring around dsRNA, capping one end, while contacting both strands using previously uncharacterized motifs to recognize dsRNA. Small-angle X-ray scattering, limited proteolysis and differential scanning fluorimetry indicate that RIG-I is in an extended and flexible conformation that compacts upon binding RNA. These results provide a detailed view of the role of helicase in dsRNA recognition, the synergy between the RD and the helicase for RNA binding and the organization of full-length RIG-I bound to dsRNA, and provide evidence of a conformational change upon RNA binding. The RIG-I helicase-RD structure is consistent with dsRNA translocation without unwinding and cooperative binding to RNA. The structure yields unprecedented insight into innate immunity and has a broader impact on other areas of biology, including RNA interference and DNA repair, which utilize homologous helicase domains within DICER and FANCM.

Jiang, Fuguo; Ramanathan, Anand; Miller, Matthew T.; Tang, Guo-Qing; Gale, Jr., Michael; Patel, Smita S.; Marcotrigiano, Joseph (Rutgers); (RWJ-Med); (UW-MED)

2012-05-29T23:59:59.000Z

137

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

138

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Wednesday, 28 April 2010 00:00 Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

139

Rigged Hilbert space formalism as an extended mathematical formalism for quantum systems. II. Transformation theory in nonrelativistic quantum mechanics  

Science Conference Proceedings (OSTI)

Results of a previous paper are used to obtain a rigorous mathematical formulation of the transformation theory of nonrelativistic quantum mechanics within the framework of rigged Hilbert spaces.

O. Melsheimer

1974-01-01T23:59:59.000Z

140

Microwave lamp with multi-purpose rotary motor  

DOE Patents (OSTI)

In a microwave powered electrodeless lamp, a single rotary motor is used to (a) rotate the bulb and (b) provide rotary motion to a blower or pump means for providing cooling fluid to the magnetron and/or to a forced gas cooler for providing cooling gas to the bulb. The blower may consist of only of an impeller without the usual blower housing. The motor, bulb stem and bulb, or motor, bulb stem, bulb and blower may be formed as an integral unit so as to facilitate replacement. 8 figs.

Ury, M.G.; Turner, B.; Wooten, R.D.

1999-02-02T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Microwave lamp with multi-purpose rotary motor  

DOE Patents (OSTI)

In a microwave powered electrodeless lamp, a single rotary motor is used to a) rotate the bulb and b) provide rotary motion to a blower or pump means for providing cooling fluid to the magnetron and/or to a forced gas cooling for providing cooler gas to the bulb. The blower may consist of only of an impeller without the usual blower housing. The motor, bulb stem and bulb, or motor, bulb stem, bulb and blower may be formed as an integral unit so as to facilitate replacement.

Ury, Michael G. (Bethesda, MD); Turner, Brian (Myersville, MD); Wooten, Robert D. (Rockville, MD)

1999-01-01T23:59:59.000Z

142

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

143

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

144

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

145

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

146

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

147

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality  

NLE Websites -- All DOE Office Websites (Extended Search)

Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Rotary Firing in Ring-Shaped Protein Explains Unidirectionality Print Hexameric motor proteins represent a complex class of molecular machines that variously push and pull on biological molecules using adenosine triphosphate (ATP) as chemical fuel. A specialized class of ring-shaped motor proteins, hexameric helicases, can unwind DNA strands and perform large-scale manipulations of single-stranded nucleic acids in processes such as DNA replication, DNA repair, and gene expression. To understand how certain hexameric helicases walk with directional polarity along single-stranded nucleic acids, Berkeley researchers used x-ray crystallography at the ALS to solve the structure of a hexameric helicase, the Rho transcription termination factor (from E. coli), bound to both ATP mimics and an RNA substrate. The results showed that Rho functions like a rotary engine: as the motor spins, it pulls RNA strands through its interior. Interestingly, the rotary firing order of the motor is biased so that the Rho protein can walk in only one direction along the RNA chain.

148

Micro rotary machine and methods for using same  

SciTech Connect

A micro rotary machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft comprises a horizontal shaft and is operable to be rotated by the micro actuator. A micro tool is coupled to the micro shaft and is operable to perform work in response to motion of the micro shaft.

Stalford, Harold L. (Norman, OK)

2012-04-17T23:59:59.000Z

149

EVALUATION OF ALTERNATIVE FILTER MEDIA FOR THE ROTARY MICROFILTER  

SciTech Connect

SRS is currently developing and testing several processes to treat high level radioactive liquid waste. These processes include the Integrated Salt Disposition Process (ISDP), the Salt Waste Processing Facility (SWPF), and the Small Column Ion Exchange Process (SCIX). Each of these processes has a solid-liquid separation process that limits its throughput. SRNL researchers identified and tested the rotary microfilter as a technology to increase solid-liquid separation throughput. The testing showed significant improvement in filter flux with the rotary microfilter over the baseline crossflow filter (i.e., 2.5-6.5X during scoping tests, as much as 10X in actual waste tests, and approximately 3X in pilot-scale tests). SRNL received funding from DOE EM-21, and subsequently DOE EM-31 to develop the rotary microfilter for high level radioactive service. The work has included upgrading the rotary microfilter for radioactive service, testing with simulated SRS waste streams, and testing it with simulated Hanford waste streams. While the filtration rate is better than that obtained during testing of crossflow filters, the authors believe the rotary microfilter throughput can be improved by using a better filter membrane. The rotary microfilter membrane is made of stainless steel (Pall PMM050). Previous testing, funded by DOE EM-21, showed that asymmetric filters composed of a ceramic membrane on top of a stainless steel support produced higher filter flux than 100% stainless steel symmetric filters in crossflow filter tests. In that testing, the Pall Accusep and Graver filters produced 13-21% larger filter flux than the baseline 0.1 {micro}m Mott filter. While the improvement in flux is not as dramatic as the improvement of the rotary filter over a crossflow filter, a 13-21% increase could reduce the lifetime of a 30 year process by 4-6 years, with significant cost savings. Subsequent rotary filter testing showed the Pall PMM050 stainless steel filter membrane produced higher flux than the Mott filter media in bench-scale and pilot-scale testing. The Accusep and Graver filter media were not evaluated in that testing, because they are not available as flat sheets. The Accusep filter was developed at ORNL and licensed to Pall Corporation. This filter has a stainless steel support structure with a zirconium oxide ceramic membrane. The pore size is 0.1 {micro}m absolute. The Graver filter has a stainless steel support structure with a titanium dioxide ceramic membrane. The pore size is 0.07 {micro}m absolute. SRNL and ORNL are working together to develop filter media similar to the Accusep and Graver media, and to test them in a bench-scale filtration apparatus to attempt to improve the throughput of the rotary microfilter. This report describes the effort.

Poirier, M.; Herman, D.; Bhave, R.

2011-09-13T23:59:59.000Z

150

Typical fault mode determination for rotor test rig based on correlation dimension and Kolmogorov entropy  

Science Conference Proceedings (OSTI)

This paper experimentally investigates the vibration faults of rotor, such as the unbalance, the loosening and the friction, using the rotor test rig. According to the theory of fractal and chaos, the vibration signal series are reconstructed. By the ... Keywords: Kolmogorov entropy, correlation dimension, fractal and chaos, vibration fault

Fengling Zhang; Yanting Ai; Fei Liu

2009-08-01T23:59:59.000Z

151

A Built for Purpose Micro-Hole Coiled Tubing Rig (MCTR)  

Science Conference Proceedings (OSTI)

This report will serve as the final report on the work performed from the contract period October 2005 thru April 2007. The project 'A Built for Purpose Microhole Coiled Tubing Rig (MCTR)' purpose was to upgrade an existing state-of-the-art Coiled Tubing Drilling Rig to a Microhole Coiled Tubing Rig (MCTR) capable of meeting the specifications and tasks of the Department of Energy. The individual tasks outlined to meet the Department of Energy's specifications are: (1) Concept and development of lubricator and tool deployment system; (2) Concept and development of process control and data acquisition; (3) Concept and development of safety and efficiency improvements; and (4) Final unit integration and testing. The end result of the MCTR upgrade has produced a unit capable of meeting the following requirements: (1) Capable of handling 1-inch through 2-3/8-inch coiled tubing (Currently dressed for 2-3/8-inch coiled tubing and capable of running up to 3-1/2-inch coiled tubing); (2) Capable of drilling and casing surface, intermediate, production and liner hole intervals; (3) Capable of drilling with coiled tubing and has all controls and installation piping for a top drive; (4) Rig is capable of running 7-5/8-inch range 2 casing; and (5) Capable of drilling 5,000 ft true vertical depth (TVD) and 6,000 ft true measured depth (TMD).

Bart Patton

2007-09-30T23:59:59.000Z

152

Solids transportation model of an industrial rotary dryer  

SciTech Connect

A complete simulation model has been developed for an industrial rotary dryer to account for the heat and mass exchange between the solids and the gas. This simulator is mainly composed of three models: solids transportation model, furnace model, and gas model. The solids transportation model is the modified Cholette-Cloutier model. It consists of a series of interactive reservoirs which are subdivided into an active and dead compartments to account for the characteristic extended tail of the residence time distribution (RTD) curves observed in industrial dryers. To expand the validity of the model, experiments have been performed in an industrial rotary dryer to obtain RTD curves under different mineral concentrate and gas flow rates. This paper describes these experiments and presents the variation of the average residence time and model parameters as function of solids and gas flow rates.

Renaud, M.; Thibault, J.; Trusiak, A.

2000-05-01T23:59:59.000Z

153

Skew and twist resistant hydrodynamic rotary shaft seal  

DOE Patents (OSTI)

A hydrodynamically lubricated squeeze packing type rotary shaft seal suitable for lubricant retention and environmental exclusion which incorporates one or more resilient protuberances which cooperate with the gland walls to hold the seal straight in its installation groove in unpressurized and low pressure lubricant retention applications thereby preventing skew-induced wear caused by impingement of abrasive contaminants present in the environment, and which also serve as radial bearings to prevent tipping of the seal within its installation gland. 14 figs.

Dietle, L.; Kalsi, M.S.

1999-02-23T23:59:59.000Z

154

Skew and twist resistant hydrodynamic rotary shaft seal  

DOE Patents (OSTI)

A hydrodynamically lubricated squeeze packing type rotary shaft seal suitable for lubricant retention and environmental exclusion which incorporates one or more resilient protuberances which and cooperate with the gland walls to hold the seal straight in its installation groove in unpressurized and low pressure lubricant retention applications thereby preventing skew-induced wear caused by impingement of abrasive contaminants present in the environment, and which also serve as radial bearings to prevent tipping of the seal within its installation gland.

Dietle, Lannie (Sugar Land, TX); Kalsi, Manmohan Singh (Houston, TX)

1999-01-01T23:59:59.000Z

155

Evaluation of Alternative Filter Media for the Rotary Microfilter  

SciTech Connect

The Savannah River Site is currently developing and testing several processes to treat high level radioactive liquid waste. Each of these processes has a solid-liquid separation process that limits its throughput. Savannah River National Laboratory researchers identified and tested the rotary microfilter as a technology to increase solid-liquid separation throughput. The authors believe the rotary microfilter throughput can be improved by using a better filter membrane. Previous testing showed that asymmetric filters composed of a ceramic membrane on top of a stainless steel support produced higher filter flux than 100% stainless steel symmetric filters in crossflow filter tests. Savannah River National Laboratory and Oak Ridge National Laboratory are working together to develop asymmetric ceramic ? stainless steel composite filters and asymmetric 100% stainless steel filters to improve the throughput of the rotary microfilter. The Oak Ridge National Laboratory Inorganic Membrane Group fabricated samples of alternative filter membranes. In addition, Savannah River National Laboratory obtained samples of filter membranes from Pall, Porvair, and SpinTek. They tested these samples in a static test cell with feed slurries containing monosodium titanate and simulated sludge.

Poirier, M. R.; Herman, D. T.; Bhave, R.

2011-11-09T23:59:59.000Z

156

Further Characterization of New NiTi Wire and Rotary Endodontic ...  

Science Conference Proceedings (OSTI)

Presentation Title, Further Characterization of New NiTi Wire and Rotary ... Higher-resolution transmission electron microscopy examination of M-Wire used to ...

157

A rotary-airlock valve resists abrasive mixtures  

SciTech Connect

Hill and Griffith (H and G, Cincinnati, Ohio) is a leading supplier of custom-blended additives to founderies. Thousands of tons of clay and carbon blends such as bentonite, gilsonite and pulverized coal, pass through the company's rotary-airlock feeding system each month. H and G's original rotary valves had cylinders lined with chrome, and closed-end rotors with tips made from nickel-chromium alloys. These valves remained in service for a maximum of only three months each. During that time, the abrasive mixtures passing through the valves virtually eroded them, increasing tolerances and causing significant air leakage. The leaks caused the pneumatic line to plug up, reducing the velocity of the line below the minimum level needed to carry any material. To overcome the leakage, a second blower was added to the system. This unit supplied an additional 40 brake hp to the pneumatic-conveying line. With constant maintenance of the valve and the continuous operation of both blowers, H and G was able to extend the valve's life by nine months. After 20 years of trying valves with various configuration, H and G installed a Smoot Type 6 rotary-airlock valve in September of 1985. The new valve's internals were made from abrasion-resistant grades of NiHard and Stellite. This combination of alloys prolonged the active life of the valve by improving its abrasion resistance. During its first year, the Smoot valve did not break down, leak air or require use of the secondary blower. After its first year of service no wear was found on the valve's internal surfaces. Another mechanical analysis was performed in 1991, after five additional years of valve operation. The valve, which had now handled more than 250,000 tons of product, showed minimal wear. H and G's capital costs had been reduced from 25[cents]/ton to 3[cents]/ton by the new valve.

Not Available

1993-03-01T23:59:59.000Z

158

Research for the Crane Boom Length Coefficient Considering the Tower Head Flexibility in Rotary Plane  

Science Conference Proceedings (OSTI)

When the crane boom length in rotary plane is determined, the traditional methods only consider support condition, non-uniform, boom end lateral displacement constraint effect of amplitude dragline and hoist rope tensile forces. Ignoring tower head elastic ... Keywords: Equivalent elastic support method, Rotary plane, Tower head flexibility, Non-conservative loading, Length coefficient

Zhang Guangyun; Lan Peng; Lu Nianli

2011-01-01T23:59:59.000Z

159

Skew And Twist Resistant Hydrodynamic Rotary Shaft Seal  

SciTech Connect

A hydrodynamically lubricated squeeze packing type rotary shaft seal suitable for lubricant retention and environmental exclusion which incorporates one or more resilient protuberances which and cooperate with the gland walls to hold the seal straight in its installation groove in unpressurized and low pressure lubricant retention applications thereby preventing skew-induced wear caused by impingement of abrasive contaminants present in the environment, and which also serve as radial bearings to prevent tipping of the seal within its installation gland. Compared to prior art, this invention provides a dramatic reduction of seal and shaft wear in abrasive environments and provides a significant increase in seal life.

Dietle, Lannie (Sugar Land, TX); Kalsi, Manmohan Singh (Houston, TX)

2000-03-14T23:59:59.000Z

160

System and method for cooling a superconducting rotary machine  

Science Conference Proceedings (OSTI)

A system for cooling a superconducting rotary machine includes a plurality of sealed siphon tubes disposed in balanced locations around a rotor adjacent to a superconducting coil. Each of the sealed siphon tubes includes a tubular body and a heat transfer medium disposed in the tubular body that undergoes a phase change during operation of the machine to extract heat from the superconducting coil. A siphon heat exchanger is thermally coupled to the siphon tubes for extracting heat from the siphon tubes during operation of the machine.

Ackermann, Robert Adolf (Schenectady, NY); Laskaris, Evangelos Trifon (Schenectady, NY); Huang, Xianrui (Clifton Park, NY); Bray, James William (Niskayuna, NY)

2011-08-09T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

DEVELOPMENT OF A ROTARY MICROFILTER FOR RADIOACTIVE WASTE APPLICATIONS  

Science Conference Proceedings (OSTI)

The processing rate of Savannah River Site (SRS) high-level waste decontamination processes are limited by the flow rate of the solid-liquid separation. The baseline process, using a 0.1 micron cross-flow filter, produces {approx}0.02 gpm/sq. ft. of filtrate under expected operating conditions. Savannah River National Laboratory (SRNL) demonstrated significantly higher filter flux for actual waste samples using a small-scale rotary filter. With funding from the U. S. Department of Energy Office of Cleanup Technology, SRNL personnel are evaluating and developing the rotary microfilter for radioactive service at SRS. The authors improved the design for the disks and filter unit to make them suitable for high-level radioactive service. They procured two units using the new design, tested them with simulated SRS wastes, and evaluated the operation of the units. Work to date provides the following conclusions and program status: (1) The authors modified the design of the filter disks to remove epoxy and Ryton{reg_sign}. The new design includes welding both stainless steel and ceramic coated stainless steel filter media to a stainless steel support plate. The welded disks were tested in the full-scale unit. They showed good reliability and met filtrate quality requirements. (2) The authors modified the design of the unit, making installation and removal easier. The new design uses a modular, one-piece filter stack that is removed simply by disassembly of a flange on the upper (inlet) side of the filter housing. All seals and rotary unions are contained within the removable stack. (3) While it is extremely difficult to predict the life of the seal, the vendor representative indicates a minimum of one year in present service conditions is reasonable. Changing the seal face material from silicon-carbide to a graphite-impregnated silicon-carbide is expected to double the life of the seal. Replacement of the current seal with an air seal could increase the lifetime to 5 years and is undergoing testing in the current work. (4) The bottom bushing showed wear due to a misalignment during the manufacture of the filter tank. Replacing the graphite bushing with a more wear resistant material such as a carbide material will increase the lifetime of the bushing. This replacement requires a more wear resistant part or coating to prevent excessive wear of the shaft. The authors are currently conducting testing with the more wear resistant bushing. (5) The project team plans to use the rotary microfilter as a filter in advance of an ion exchange process under development for potential deployment in SRS waste tank risers.

Poirier, M; David Herman, D; Samuel Fink, S

2008-02-25T23:59:59.000Z

162

Comparison of residence time models for cascading rotary dryers  

SciTech Connect

The predictions of the models of Matchett and Baker (1988), Saeman and Mitchell (1954) and Friedman and Marshall (1949) for the solids residence time in rotary dryers have been compared with both pilot-scale and industrial-scale data. A countercurrent pilot-scale dryer of 0.2m diameter and 2m long has been used with air velocities up to 1.5 m to measure the residence times of sorghum grain. The average discrepancy for the solids residence time between the predictions and the experiments that were carried out in the pilot-scale rotary dryer is {minus}10.4%. Compared with the models of Friedman and Marshall (1949) and Saeman and Mitchell (1954) for the pilot-scale data obtained here, the Matchett and Baker model is more satisfactory for predicting the solids residence time in this pilot-scale dryer. It has also been found that the model of Matchett and Baker describes the industrial data of Saeman and Mitchell (1954) than the correlation of Friedman and Marshall (1949).

Cao, W.F.; Langrish, T.A.G. [Univ. of Sydney, New South Wales (Australia). Dept. of Chemical Engineering

1999-04-01T23:59:59.000Z

163

Wear compensating seal means for rotary piston coal feeder  

SciTech Connect

The present invention is directed to a wear compensating seal arrangement for use in a rotary piston feeder utilized for feeding pulverized coal into a gasifier operating at relatively high pressures and elevated temperatures. The rotary piston feeder has a circular casing with a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable disoidal rotor having a cylinder in which a reciprocatable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam whereby pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder and then discharged therefrom into the high pressure gasifier while maintaining minimal losses of producer gas and the expenditure of minimal energy which would detract from the efficiency of the gasification. The seal arrangement of the present invention is disposed between the rotor and the casing about the coal discharge and prevents the high pressure gases from within the gasifier from escaping between these relatively movable parts during operation of the coal feeder. The seal utilizes a primary seal in contact with the rotor and a secondary seal supporting the primary seal. The primary seal is continuously urged towards the rotor by springs and the high pressure producer gas.

Gencsoy, Hasan T. (Morgantown, WV); Gardner, John F. (Morgantown, WV)

1979-01-01T23:59:59.000Z

164

Use of fan rig data for the understanding and prediction of fan broadband noise and noise changes due to a variable area nozzle.  

E-Print Network (OSTI)

??This thesis presents the results of the research component of this EngD, entitled Use of fan rig data for the understanding and prediction of fan… (more)

Deane, Eugene Pio

2009-01-01T23:59:59.000Z

165

Passenger vehicle tire rolling resistance can be predicted from a flat-belt test rig  

Science Conference Proceedings (OSTI)

The rolling resistance of fifteen different types of tire was determined on-road by coastdown tests, using several vehicles variously fitted with 14 and 15 inch wheels. Corrections for tire pressure, and for external temperature, were deduced by data regression. The rolling resistance of the same tires was measured on a flat-belt tire test machine, and correction for tire pressure was determined in a like manner. In this paper, the results, in terms of the characteristic rolling resistance, are compared between rig and road. The various test procedures are discussed.

Ivens, J.

1989-01-01T23:59:59.000Z

166

Continuous injection of an inert gas through a drill rig for drilling into potentially hazardous areas  

DOE Patents (OSTI)

A drill rig for drilling in potentially hazardous areas includes a drill having conventional features such as a frame, a gear motor, gear box, and a drive. A hollow rotating shaft projects through the drive and frame. An auger, connected to the shaft is provided with a multiplicity of holes. An inert gas is supplied to the hollow shaft and directed from the rotating shaft to the holes in the auger. The inert gas flows down the hollow shaft, and then down the hollow auger, and out through the holes in the bottom of the auger into the potentially hazardous area.

McCormick, S.H.; Pigott, W.R.

1998-04-01T23:59:59.000Z

167

Development of a Low-Cost Rotary Steerable Drilling System  

DOE Green Energy (OSTI)

The project had the goal to develop and commercialize a low-cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures to reduce operating costs by a minimum of 50% and lost-in-hole charges by at least 50% over the currently offered systems. The LCRSS system developed under this project does reduce operating costs by 55% and lost-in-hole charges by at least 50%. The developed product is not commercializable in its current form. The overall objective was to develop and commercialize a low cost rotary steerable system (LCRSS) capable of operating downhole at conventional pressures and temperatures (20,000 psi/150 C) while reducing the operating costs by 50% and the lost-in-hole charges by 50% over the currently available systems. The proposed reduction in costs were to be realized through the significant reduction in tool complexity, a corresponding increase in tool reliability as expressed in the mean-time between failure (MTBF), and a reduction in the time and costs required to service tools after each field operation. Ultimately, the LCRSS system was to be capable of drilling 7 7/8 in. to 9 5/8 in. borehole diameters. The project was divided into three Phases, of which Phases I & II were previously completed and reported on, and are part of the case file. Therefore, the previously reported information is not repeated herein. Phase III included the fabrication of two field ready prototypes that were to be subjected to a series of drilling tests at GTI Catoosa, DOE RMOTC, and at customer partnering wells, if possible, as appropriate in the timing of the field test objectives to fully exercise all elements of the LCRSS. These tests were conducted in an iterative process based on a performance/reliability improvement cycle with the goal of demonstrating the system met all aspects required for commercial viability. These tests were conducted to achieve continuous runs of 100+ hours with well trajectories that fully exercised the tool's build/turn/drop/hold target capabilities and its higher end ratings for bit weight, torque and rotary speed. The tool teardowns were rigorously analyzed at the conclusion of each field run to assess component wear rates and to fully document any detrimental behavior(s) observed.

Roney Nazarian

2012-01-31T23:59:59.000Z

168

High pressure rotary piston coal feeder for coal gasification applications  

DOE Patents (OSTI)

The subject development is directed to an apparatus for feeding pulverized coal into a coal gasifier operating at relatively high pressures and elevated temperatures. This apparatus is a rotary piston feeder which comprises a circular casing having a coal loading opening therein diametrically opposed from a coal discharge and contains a rotatable discoid rotor having a cylinder in which a reciprocateable piston is disposed. The reciprocation of the piston within the cylinder is provided by a stationary conjugate cam arrangement whereby the pulverized coal from a coal hopper at atmospheric pressure can be introduced into the cylinder cavity and then discharged therefrom into the high-pressure gasifier without the loss of high pressure gases from within the latter.

Gencsoy, Hasan T. (Morgantown, WV)

1977-05-24T23:59:59.000Z

169

Rim for rotary inertial energy storage device and method  

DOE Patents (OSTI)

The present invention is directed to an improved rim or a high-performance rotary inertial energy storage device (flywheel). The improved rim is fabricated from resin impregnated filamentary material which is circumferentially wound in a side-by-side relationship to form a plurality of discretely and sequentially formed concentric layers of filamentary material that are bound together in a resin matrix. The improved rim is provided by prestressing the filamentary material in each successive layer to a prescribed tension loading in accordance with a predetermined schedule during the winding thereof and then curing the resin in each layer prior to forming the next layer for providing a prestress distribution within the rim to effect a self-equilibrating compressive prestress within the windings which counterbalances the transverse or radial tensile stresses generated during rotation of the rim for inhibiting deleterious delamination problems.

Knight, Jr., Charles E. (Knoxville, TN); Pollard, Roy E. (Powell, TN)

1980-01-01T23:59:59.000Z

170

Advanced coal-fueled industrial cogeneration gas turbine system: Hot End Simulation Rig  

DOE Green Energy (OSTI)

This Hot End Simulation Rig (HESR) was an integral part of the overall Solar/METC program chartered to prove the technical, economic, an environmental feasibility of a coal-fueled gas turbine, for cogeneration applications. The program was to culminate in a test of a Solar Centaur Type H engine system operated on coal slurry fuel throughput the engine design operating range. This particular activity was designed to verify the performance of the Centaur Type H engine hot section materials in a coal-fired environment varying the amounts of alkali, ash, and sulfur in the coal to assess the material corrosion. Success in the program was dependent upon the satisfactory resolution of several key issues. Included was the control of hot end corrosion and erosion, necessary to ensure adequate operating life. The Hot End Simulation Rig addressed this important issue by exposing currently used hot section turbine alloys, alternate alloys, and commercially available advanced protective coating systems to a representative coal-fueled environment at turbine inlet temperatures typical of Solar`s Centaur Type H. Turbine hot end components which would experience material degradation include the transition duct from the combustor outlet to the turbine inlet, the shroud, nozzles, and blades. A ceramic candle filter vessel was included in the system as the particulate removal device for the HESR. In addition to turbine material testing, the candle material was exposed and evaluated. Long-term testing was intended to sufficiently characterize the performance of these materials for the turbine.

Galica, M.A.

1994-02-01T23:59:59.000Z

171

Modeling and simulation of two-leaf semi-rotary VAWT  

Science Conference Proceedings (OSTI)

In this paper, according to the structural characteristics of two-leaf semi-rotary VAWT (vertical axis wind turbine), the microelement method and the coordinate system rotation method are used to establish the mathematical model of wind turbine and, ...

Qian Zhang; Haifeng Chen; Binbin Wang

2010-09-01T23:59:59.000Z

172

Bias in hard disk drive rotary actuator pivot bearings: measurements and lubrication phenomena  

Science Conference Proceedings (OSTI)

Bias in disk drive rotary actuator bearings exhibits complex behavior related to the history of the actuator movement. This paper investigates the hysteresis component of bias present after seeks. Measurements of bias during full stroke actuator movements ...

Daniel Helmick; William Messner; C. Fred Higgs, III

2007-04-01T23:59:59.000Z

173

Generation of Optimal Unit Distance Codes for Rotary Encoders through Simulated Evolution  

Science Conference Proceedings (OSTI)

An evolutionary algorithm is used to generate unit distance codes for absolute rotary encoders. The target is to obtain a code suitable for disk size reduction, or for resolution increase, thus overcoming the limitations of conventional Gray codes. Obtained ...

Stefano Gregori; Roberto Rossi; Guido Torelli; Valentino Liberali

2001-04-01T23:59:59.000Z

174

GA 200-500 (VSD): Oil-injected rotary screw compressors, 200 ...  

U.S. Energy Information Administration (EIA)

GA 200-500 (VSD): Oil-injected rotary screw compressors, 200-500 kW / 268-670 hp.,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

175

GA 30+-90 / GA 37-90 VSD: Oil-injected rotary screw ...  

U.S. Energy Information Administration (EIA)

GA 30+-90 / GA 37-90 VSD: Oil-injected rotary screw compressors, 30-90 kW / 40-125 hp,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

176

GAe11-30 / GAe 18-30 VSD: Oil-injected rotary screw ...  

U.S. Energy Information Administration (EIA)

GAe11-30 / GAe 18-30 VSD: Oil-injected rotary screw compressors, 11-30 kW / 15-40 hp,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

177

GA 11+-30/GA 15-30 VSD: Oil-injected rotary screw compressors ...  

U.S. Energy Information Administration (EIA)

GA 11+-30/GA 15-30 VSD: Oil-injected rotary screw compressors, 11-30 kW / 15-40 hp,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading air ...

178

GA 90+-160+ / GA 110-160 VSD: Oil-injected rotary screw ...  

U.S. Energy Information Administration (EIA)

GA 90+-160+ / GA 110-160 VSD: Oil-injected rotary screw compressors, 90-160 kW / 125-200 hp.,Kunshan CompAirs Machinery Plant Co.,Ltd is the leading ...

179

Granular Attrition due to Rotary Valve in a Pneumatic Conveying System  

E-Print Network (OSTI)

The rotary valve is a widely used mechanical device in many solids-handling industrial processes. However, it may also be responsible for most of the attrition effects occurring in a typical process. In this study, the ...

Yao, Jun

180

Specific features in building hardware-software complexes operating in real-time: An example of test rig used in periodic tests of reducers  

Science Conference Proceedings (OSTI)

Test rig for periodic tests of reducers is involved as an example to discuss specific features in building automatic test systems (ATS); the test rig is designed at ZAO NPP MIKS Engineering. A certain approach to ATS design based on adaptation of universal ...

A. A. Urakov; M. A. Rylov; D. S. Shutov; P. G. Dorofeev

2011-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Laws Envirosearch Institutional Controls NEPA Activities RCRA RQ*Calculator Water HSS Logo Water Laws Overview of water-related legislation affecting DOE sites Clean...

182

The Feasibility of Natural Gas as a Fuel Source for Modern Land-Based Drilling Rigs  

E-Print Network (OSTI)

The purpose of this study is to determine the feasibility of replacing diesel with natural gas as a fuel source for modern drilling rigs. More specifically, this thesis (1) establishes a control baseline by examining operational characteristics (response, fuel usage, and cost) of an existing diesel-powered land rig during the drilling of a well in the Haynesville Shale; (2) estimates operational characteristics of a natural gas engine under identical conditions; and (3) draws a comparison between diesel and natural gas engines, determining the advantages and disadvantages of those fuel sources in drilling applications. Results suggest that diesel engines respond to transient loads very effectively because of their inherently higher torque, especially when compared with natural gas engines of a similar power rating. Regarding fuel consumption, the engines running on diesel for this study were more efficient than on natural gas. On a per-Btu basis, the natural gas engines consumed nearly twice as much energy in drilling the same well. However, because of the low price of natural gas, the total cost of fuel to drill the well was lowered by approximately 54%, or 37,000 USD. Based on the results, it is possible to infer that the use of natural gas engines in drilling environments is feasible, and in most cases, an economical and environmental advantage. First, when compared with diesel, natural gas is a cleaner fuel with less negative impact on the environment. Second, fuel cost can be reduced by approximately half with a natural gas engine. On the other hand, natural gas as a fuel becomes less practical because of challenges associated with transporting and storing a gas. In fact, this difficulty is the main obstacle for the use of natural gas in drilling environments. In conclusion, because of its minimal drawback on operations, it is recommended that in situations where natural gas is readily available near current market prices, natural gas engines should be utilized because of the cost savings and reduced environmental impact. In all other cases, particularly where transport and storage costs encroach on the cost benefit, it may still be advantageous to continue powering rigs with diesel because of its ease of use.

Nunn, Andrew Howard

2011-12-01T23:59:59.000Z

183

Hydrodynamically Lubricated Rotary Shaft Having Twist Resistant Geometry  

SciTech Connect

A hydrodynamically lubricated squeeze packing type rotary shaft with a cross-sectional geometry suitable for pressurized lubricant retention is provided which, in the preferred embodiment, incorporates a protuberant static sealing interface that, compared to prior art, dramatically improves the exclusionary action of the dynamic sealing interface in low pressure and unpressurized applications by achieving symmetrical deformation of the seal at the static and dynamic sealing interfaces. In abrasive environments, the improved exclusionary action results in a dramatic reduction of seal and shaft wear, compared to prior art, and provides a significant increase in seal life. The invention also increases seal life by making higher levels of initial compression possible, compared to prior art, without compromising hydrodynamic lubrication; this added compression makes the seal more tolerant of compression set, abrasive wear, mechanical misalignment, dynamic runout, and manufacturing tolerances, and also makes hydrodynamic seals with smaller cross-sections more practical. In alternate embodiments, the benefits enumerated above are achieved by cooperative configurations of the seal and the gland which achieve symmetrical deformation of the seal at the static and dynamic sealing interfaces. The seal may also be configured such that predetermined radial compression deforms it to a desired operative configuration, even through symmetrical deformation is lacking.

Dietle, Lannie (Houston, TX); Gobeli, Jeffrey D. (Houston, TX)

1993-07-27T23:59:59.000Z

184

Sway control method and system for rotary cranes  

DOE Patents (OSTI)

Methods and apparatuses for reducing the oscillatory motion of rotary crane payloads during operator-commanded or computer-controlled maneuvers. An Input-shaping filter receives input signals from multiple operator input devices and converts them into output signals readable by the crane controller to dampen the payload tangential and radial sway associated with rotation of the jib. The input signals are characterized by a hub rotation trajectory .gamma.(t), which includes a jib angular acceleration .gamma., a trolley acceleration x, and a load-line length velocity L. The system state variables are characterized by a tangential rotation angle .theta.(t) and a radial rotation angle .phi.(t) of the load-line. The coupled equations of motion governing the filter are non-linear and configuration-dependent. In one embodiment, a filter is provided between the operator and the crane for filtering undesired frequencies from the angular .gamma. and trolley x velocities to suppress payload oscillation. In another embodiment, crane commands are computer generated and controlled to suppress vibration of the payload using a postulated asymmetrical shape for the acceleration profiles of the jib, which profiles are uniquely determined by a set of parameters (including the acceleration pulse amplitude and the duration and coast time between pulses), or a dynamic programming approach.

Robinett, Rush D. (Tijeras, NM); Parker, Gordon G. (Houghton, MI); Feddema, John T. (Albuquerque, NM); Dohrmann, Clark R. (Albuquerque, NM); Petterson, Ben J. (Albuquerque, NM)

1999-01-01T23:59:59.000Z

185

Coal desulfurization in a rotary kiln combustor. Final report, March 15, 1990--July 31, 1991  

Science Conference Proceedings (OSTI)

The purpose of this project was to demonstrate the combustion of coal and coal wastes in a rotary kiln reactor with limestone addition for sulfur control. The rationale for the project was the perception that rotary systems could bring several advantages to combustion of these fuels, and may thus offer an alternative to fluid-bed boilers. Towards this end, an existing wood pyrolysis kiln (the Humphrey Charcoal kiln) was to be suitably refurbished and retrofitted with a specially designed version of a patented air distributor provided by Universal Energy, Inc. (UEI). As the project progressed beyond the initial stages, a number of issues were raised regarding the feasibility and the possible advantages of burning coals in a rotary kiln combustor and, in particular, the suitability of the Humphrey Charcoal kiln as a combustor. Instead, an opportunity arose to conduct combustion tests in the PEDCO Rotary Cascading-Bed Boiler (RCBB) commercial demonstration unit at the North American Rayon CO. (NARCO) in Elizabethton, TN. The tests focused on anthracite culm and had two objectives: (a) determine the feasibility of burning anthracite culms in a rotary kiln boiler and (b) obtain input for any further work involving the Humphrey Charcoal kiln combustor. A number of tests were conducted at the PEDCO unit. The last one was conducted on anthracite culm procured directly from the feed bin of a commercial circulating fluid-bed boiler. The results were disappointing; it was difficult to maintain sustained combustion even when large quantities of supplemental fuel were used. Combustion efficiency was poor, around 60 percent. The results suggest that the rotary kiln boiler, as designed, is ill-suited with respect to low-grade, hard to burn solid fuels, such as anthracite culm. Indeed, data from combustion of bituminous coal in the PEDCO unit suggest that with respect to coal in general, the rotary kiln boiler appears inferior to the circulating fluid bed boiler.

Cobb, J.T. Jr.

1992-09-11T23:59:59.000Z

186

Rotary seal with enhanced lubrication and contaminant flushing  

DOE Patents (OSTI)

A resilient, ring shaped interference-type hydrodynamic rotary seal having waves on the lubricant side which provide increased film thickness and flushing action by creating contact pressure induced angulated restrictions formed by abrupt restrictive diverters. The angulated restrictions are defined by projecting ridges, corners at the trailing edge of the waves, or simply by use of a converging shape at the trailing edge of the waves which is more abrupt than the gently converging hydrodynamic inlet shape at the leading edge of the waves. The abrupt restrictive diverter performs two functions; a restricting function and a diverting function. The angulated restrictions cause a local film thickness restriction which produces a damming effect preventing a portion of the lubricant from leaking out of the dynamic sealing interface at the trailing edge of the wave, and results in a much thicker lubricant film thickness under the waves. This contributes to more film thickness in the remainder of the dynamic sealing interface toward the environment because film thickness tends to decay gradually rather than abruptly due to the relative stiffness of the seal material. Because of the angle of the abrupt restrictive diverter relative to the relative rotation direction, in conjunction with the restriction or damming effect, a strong diverting action is produced which pumps lubricant across the dynamic sealing interface toward the environment. The lubricant diversion is caused by the component of the rotational velocity tangent to the abrupt restrictive diverter. The component of rotational velocity normal to the abrupt restrictive diverter causes a portion of the lubricant film to be pumped past the abrupt restrictive diverter, thereby assuring adequate lubrication thereof.

Dietle, Lannie L. (Sugar Land, TX)

2000-01-01T23:59:59.000Z

187

Design and Analysis of a Test Rig for Modeling the Bit/Formation Interface in Petroleum Drilling Applications  

E-Print Network (OSTI)

Equipment failure and well deviations are prevailing contributors to production delays within the petroleum industry. Particular monetary focus is given to the drilling operations of wells to overcome these deficits, in order to extract natural resources as efficiently, and as safely, as possible. The research presented here focuses on minimizing vibrations of the drill string near the bottom-hole assembly (BHA) by identifying the cause of external forcing on the drillstring in vertical and horizontal wells and measuring the effects of various factors on the stability of perturbations on the system. A test rig concept has been developed to accurately measure the interaction forces and torques between the bit, formation and fluids during drilling in order to clearly define a bit/formation interface law (BFIL) for the purpose vibrational analysis. As a secondary function, the rig will be able to measure the potential inputs to a drilling simulation code that can be used to model drillstring vibrations. All notable quantities will be measured including torque on bit (TOB), weight on bit (WOB), lateral impact loads (LIL), formation stiffness, bit specific properties, fluid damping coefficients and rate of penetration (ROP). The conceptual design has been analyzed and refined, in detail, to verify its operational integrity and range of measurement error. The operational envelope of the rig is such that a drill bit of up to 8 ½ inches in diameter can be effectively tested at desired operational parameters (WOB: 0-55,000 lbf, RPM: 60-200) with various rock formations and multiple fluid types. Future use and design possibilities are also discussed to enhance the functionality of the rig and the potential for further research in the area of oil and gas drilling and vibrational modeling.

Wilson, Joshua Kyle

2013-05-01T23:59:59.000Z

188

ALTERNATE POWER AND ENERGY STORAGE/REUSE FOR DRILLING RIGS: REDUCED COST AND LOWER EMISSIONS PROVIDE LOWER FOOTPRINT FOR DRILLING OPERATIONS  

E-Print Network (OSTI)

Diesel engines operating the rig pose the problems of low efficiency and large amount of emissions. In addition the rig power requirements vary a lot with time and ongoing operation. Therefore it is in the best interest of operators to research on alternate drilling energy sources which can make entire drilling process economic and environmentally friendly. One of the major ways to reduce the footprint of drilling operations is to provide more efficient power sources for drilling operations. There are various sources of alternate energy storage/reuse. A quantitative comparison of physical size and economics shows that rigs powered by the electrical grid can provide lower cost operations, emit fewer emissions, are quieter, and have a smaller surface footprint than conventional diesel powered drilling. This thesis describes a study to evaluate the feasibility of adopting technology to reduce the size of the power generating equipment on drilling rigs and to provide ?peak shaving? energy through the new energy generating and energy storage devices such as flywheels. An energy audit was conducted on a new generation light weight Huisman LOC 250 rig drilling in South Texas to gather comprehensive time stamped drilling data. A study of emissions while drilling operation was also conducted during the audit. The data was analyzed using MATLAB and compared to a theoretical energy audit. The study showed that it is possible to remove peaks of rig power requirement by a flywheel kinetic energy recovery and storage (KERS) system and that linking to the electrical grid would supply sufficient power to operate the rig normally. Both the link to the grid and the KERS system would fit within a standard ISO container. A cost benefit analysis of the containerized system to transfer grid power to a rig, coupled with the KERS indicated that such a design had the potential to save more than $10,000 per week of drilling operations with significantly lower emissions, quieter operation, and smaller size well pad.

Verma, Ankit

2009-05-01T23:59:59.000Z

189

ROTARY FILTER FINES TESTING FOR SMALL COLUMN ION EXCHANGE  

SciTech Connect

SRNL was requested to quantify the amount of 'fines passage' through the 0.5 micron membranes currently used for the rotary microfilter (RMF). Testing was also completed to determine if there is any additional benefit to utilizing a 0.1 micron filter to reduce the amount of fines that could pass through the filter. Quantifying of the amount of fines that passed through the two sets of membranes that were tested was accomplished by analyzing the filtrate by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) for titanium. Even with preparations to isolate the titanium, all samples returned results of less than the instrument's detection limit of 0.184 mg/L. Test results show that the 0.5 micron filters produced a significantly higher flux while showing a negligible difference in filtrate clarity measured by turbidity. The first targeted deployment of the RMF is with the Small Column Ion Exchange (SCIX) at the Savannah River Site (SRS). SCIX uses crystalline silicotitanate (CST) to sorb cesium to decontaminate a clarified salt solution. The passage of fine particles through the filter membranes in sufficient quantities has the potential to impact the downstream facilities. To determine the amount of fines passage, a contract was established with SpinTek Filtration to operate a 3-disk pilot scale unit with prototypic filter disk and various feeds and two different filter disk membranes. SpinTek evaluated a set of the baseline 0.5 micron filter disks as well as a set of 0.1 micron filter disks to determine the amount of fine particles that would pass the membrane and to determine the flux each set produced. The membrane on both disk sets is manufactured by the Pall Corporation (PMM 050). Each set of disks was run with three feed combinations: prototypically ground CST, CST plus monosodium titanate (MST), and CST, MST, plus Sludge Batch 6 (SB6) simulant. Throughout the testing, samples of the filtrate were collected, measured for turbidity, and sent back to SRNL for analysis to quantify the amount of fines that passed through the membrane. It should be noted that even though ground CST was tested, it will be transferred to the Defense Waste Processing Facility (DWPF) feed tank and is not expected to require filtration.

Herman, D.

2011-08-03T23:59:59.000Z

190

Burning state recognition of rotary kiln using ELMs with heterogeneous features  

Science Conference Proceedings (OSTI)

Image based burning state recognition plays an important role in sintering process control of rotary kiln. Although many efforts on dealing with this problem have been made over the past years, the recognition performance cannot be satisfactory due to ... Keywords: Burning state, ELM, Eigen-flame image, Latent semantic analysis, Multivariate image analysis

Weitao Li; Dianhui Wang; Tianyou Chai

2013-02-01T23:59:59.000Z

191

Loads on Tie-Down Systems for Floating Drilling Rigs during Hurricane Conditions  

E-Print Network (OSTI)

Tie-down systems are used to fasten drilling rigs to the deck of offshore structures during harsh environmental conditions such as hurricanes. During Hurricane Ivan (2004) and Katrina (2005), a number of offshore structures were moved and several tie-down systems were damaged. In the present study, the reaction force and connection capacity of tie-down systems for a TLP and SPAR are investigated. The environmental conditions are taken from the API Bulletin 2INT-MET which has been updated after several major storms during 2004-2005. The hydrodynamic coefficients of the TLP and SPAR are obtained using a 3D diffraction/radiation panel method. The motions of the TLP and SPAR are then simulated in the time domain by using the hull-mooring-riser coupled dynamic analysis tool CHARM3D. Based on the simulated motion and acceleration time series, the inertial and gravity loads on derrick and skid base footing are calculated. In addition to the inertial-gravity loads, wind forces exerted on the derrick are also calculated. All the external forces and resultant hull motions are simulated for 100-year, 200-year and 1000-year storms to observe the derrick structural integrity with increasing environmental intensity. Various environmental headings are also considered to find the maximum reaction forces. In the present method, the phase differences between gravity-inertia forces and wind forces are taken into consideration to obtain more realistic loads on derrick and skid base footings. This research shows that the maximum and minimum load values are appreciably higher for the SPAR. In addition, the direction of external forces is also important to determine maximum reaction forces on footings. The capacities of the clamps in slip, bolt tension, and bolt shear can be also analyzed using the resultant data to provide guidance on appropriate design values.

Bae, Yoon Hyeok

2009-05-01T23:59:59.000Z

192

Radioactive air emissions program notice of construction, rotary mode core-sampling truck and exhauster  

SciTech Connect

Efforts have been ongoing to obtain core samples from the contents of each of the Hanford Site`s 149 single-shell tanks (SSTs). The SSTs contain various amounts and combinations of liquid, sludge, and saltcake. Existing sampling equipment is unable to retrieve samples of hardened waste within established tank safety restrictions (particularly limits on temperature). A new rotary mode core-sampling system has been designed to sample tanks containing hardened wastes. The prominent feature of this new system is the use of a nitrogen gas purge. The nitrogen gas purge will cool the drill bit and prevent cross contamination of different waste layers in the tank. The nitrogen gas purge will also allow more complete sample recovery, by clearing cuttings that might otherwise obstruct the sampler or drill bit. Nitrogen was chosen over other compressed gases for its inherent safety. Many of the tanks to be sampled with the rotary mode core-sampling system are not actively ventilated, these tanks are operated at atmospheric pressure with passive (breather) high-efficiency particulate air (HEPA) filters. Unless a ventilation system of the proper capacity is used, addition of the nitrogen purge gas to SSTs will cause the tanks to pressurize. Additionally, the use of the rotary mode core-sampling system will generate aerosols and dusts potentially containing radioactive particles in the tank vapor space. Consequently, an exhauster will be required during operation of the rotary mode core-sampling system on SSTs to prevent tank pressurization and to control emissions. This exhauster will be required to be moved from tank farm to tank farm with the rotary mode core-sampling system.

Not Available

1993-05-01T23:59:59.000Z

193

Design of Automation Control System for Water Chillers  

Science Conference Proceedings (OSTI)

Energy crisis led to the recognition that the energy conservation is important. The aim of performance test rig of a water chiller which is introduced in this paper is just for the energy saving. In order to get the better efficiency, a monitoring system ...

Yuhong Sun; Yuying Sun; Junmei Li; Xiaowei Yin

2009-12-01T23:59:59.000Z

194

Experimental evaluation of a metal-mesh bearing damper in a high speed test rig  

E-Print Network (OSTI)

Metal mesh is a commercially available material used in many applications including seals, heat shields, filters, gaskets, aircraft engine mounts, and vibration absorbers. This material has been tested in the Turbomachinery Laboratory at Texas A&M University (TAMU) as a bearing damper in a rotordynamic test rig. The test facility was originally used to support the design of a turboprop engine at TAMU, developing squirrel cage bearing supports and squeeze film dampers for both the gas generator and power turbine rotors. To design the metal mesh damper, static stiffness and dynamic rap test measurements were first made on metal mesh samples in a specially designed non-rotating test fixture. These property tests were performed on samples of various densities and press fits. One sample was also tested in an Instron machine as an ancillary and redundant way to determine the stiffness. Using the stiffness test results and equations derived by a previous investigator, a spreadsheet program was written and used to size metal mesh donuts that have the radial stiffness value required to replace the squirrel cage in the power turbine. The squirrel cage and squeeze-film bearing damper developed for the power turbine rotor was then replaced by a metal mesh donut sized by the computer code. Coast-down tests were conducted through the first critical speed of the power turbine. The results of the metal mesh tests were compared with those obtained from previous testing with the squeeze film damper. The results show that the metal mesh damper has the same damping as the squeeze film at room temperature but does not lose its damping at elevated temperatures up to 210F?. Experiments were run under several different conditions including balanced rotor hot oil soaked, unbalanced rotor hot oil soaked, balanced dry, and unbalanced dry. Over all, metal mesh dampers appear to be a viable and attractive substitute for squeeze film dampers in gas turbine engines. The advantages shown to date include less variation of damping with temperature, ability to handle large rotor unbalance, and the ability (if required) to operate effectively in an oil free environment.

Zarzour, Mark Joseph

1999-01-01T23:59:59.000Z

195

Internal combustion engine with rotary valve assembly having variable intake valve timing  

DOE Patents (OSTI)

An internal combustion engine has rotary valves associated with movable shutters operable to vary the closing of intake air/fuel port sections to obtain peak volumetric efficiency over the entire range of speed of the engine. The shutters are moved automatically by a control mechanism that is responsive to the RPM of the engine. A foot-operated lever associated with the control mechanism is also used to move the shutters between their open and closed positions.

Hansen, Craig N. (Eden Prairie, MN); Cross, Paul C. (Shorewood, MN)

1995-01-01T23:59:59.000Z

196

Mathematical model and the dynamic simulation of an electromechanical rotary device. [SLENOID  

SciTech Connect

A mathematical model of an electro-mechanical rotary device is presented. This device contains a rotor, stator, and two spring-loaded arms which restrict the rotor motion. The desired action is the alignment of the rotor and the consequent movement of the arms. The SLENOID computer program for calculating the magnetic torque, air gap permeance, spring torque, damping effects, and motion of the rotor and arms is described. (LCL)

Emergy, J.D.

1980-02-01T23:59:59.000Z

197

Modeling of the solids transportation within an industrial rotary dryer: A simple model  

SciTech Connect

To better understand the underlying phenomena taking place in an industrial rotary dryer and to determine the optimum operating conditions, a simulator in which the solids transportation, the gas flow, and the heat and mass transfer are modeled is currently being developed. This paper describes the use of interactive perfect mixers in series to model the solids transportation within an industrial rotary dryer, on the basis of an experimental residence time distribution curve (RTD). Two simple models are proposed: a series of perfect well-mixed interacting tanks and a modified Cholette-Cloutier model. The first model is not able to account for the nonideal behavior of the solids transportation in the rotary dryer. To account for the characteristic extended tail of the RTD curves observed in industrial dryers, in a second model, the solid phase is divided between an active and a dead zone. This model, with 36 cells and 25% of the volume occupied by the dead zones, modeled very well the industrial RTD curve. In addition, the model produces bed depth and axial velocity profiles that are consistent with those reported in the literature.

Duchesne, C.; Thibault, J.; Bazin, C. [Laval Univ., Sainte-Foy, Quebec (Canada)] [Laval Univ., Sainte-Foy, Quebec (Canada)

1996-07-01T23:59:59.000Z

198

www.myresources.com.au OIL & GAS BULLETIN VOL. 15, NO. 11 PAGE 9 Safety first: Oil rigs off the north west shelf will be studied for  

E-Print Network (OSTI)

www.myresources.com.au OIL & GAS BULLETIN VOL. 15, NO. 11 PAGE 9 NEWS Safety first: Oil rigs off for future successful tight gas exploration projects in Western Australia has been set up and studies the tight gas sand field at its exploration permit in the South Perth Basin. Professor Rezaee said

199

EVALUATION OF AP-FARM SIMULANT COMPOSITION FOR ROTARY MICROFILTER TESTING  

SciTech Connect

This document identifies the feed composition of a Hanford AP tank farm simulant for rotary microfiltration testing. The composition is based on an Hanford Tank Waste Operations Simulator (HTWOS) model run in combination with Tank Waste Information Network (TWINS) data and mineralogical studies of actual waste solids. The feed simulant is intended to be used in test runs at SRNL. The simulant will be prepared in two parts: (1) A supernate, composed of water-soluble salts and (2) The undissolved (actually, undissolvable) solids. Test slurries with distinct solids concentrations (e.g., 0.5, 5 and 10 wt%) are then prepared as needed. The base for the composition of supernate and solids is the modeled feed sequence for a deployment scenario of the Supplemental Pretreatment units within AP-farm. These units comprise a filtration part, the RMF, and a Cesium-removal part, a Small Column Ion Exchange. The primary use of this simulant is for filtration testing - however, in case that it is also used for ion-exchange tests, the amount of Cs-137 that would need to be added is available in Table 1 and Attachment 3. A modified model run (MMR-049) of the Hanford Tank Waste Operations Simulator (HTWOS) system plan 6 case 3 was performed to identify the feed sequence. Case 3 assumed supplemental treatment besides the low activity waste (LAW) melter with supplemental pretreatment supporting the pretreatment facility. The MMR did not cap the duration of supplemental pretreatment to 15 months, but rather used it throughout the entire treatment mission as an add-on option to the pretreatment facility at the Waste Treatment and Immobilization Plant (WTP). Tank 241-AP-105 (AP-105) was chosen as the feed tank to the filtration unit. Other parameters included a fixed minimum of 0.5 wt% solids in the feed and a maximum Na-concentration of 5M in the supernate. The solids rejection from the filtration unit was set to 99.99% and the maximum allowed amount of solids within tank AP-105 was set to 10 wt%. A comprehensive description of the run and the full suite of results were issued as SVF-2364-00. The list of individual feed events including the amounts of liquid and solids transferred for the first five years is added as Attachment 2; the chemical composition of the supernate feed comprises Attachment 3. For the simulant composition, only the first five years of proposed feed delivery were taken into account. The main outcome of MMR-049 was that for the first five years, the feed would come mostly from AP-farms. Multiple delivery campaigns to AP-105 are included in this average feed, while minimizing the amount of contributing tanks to the solids in the feed mix.

HUBER HJ

2011-09-19T23:59:59.000Z

200

Integrated Status and Effectiveness Monitoring Program - Entiat River Snorkel Surveys and Rotary Screw Trap, 2007.  

DOE Green Energy (OSTI)

The USFWS Mid-Columbia River Fishery Resource Office conducted snorkel surveys at 24 sites during the summer and fall periods of 2006 survey periods as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. A total of 37,938 fish from 15 species/genera and an unknown category were enumerated. Chinook salmon were the overall most common fish observed and comprised 15% of fish enumerated followed by rainbow trout (10%) and mountain whitefish (7%). Day surveys were conducted during the summer period 2007 (August), while night surveys were conducted during the fall 2007 (October) surveys. The USFWS Mid-Columbia River Fishery Resource Office (MCFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program (ISEMP) program from August through November of 2007. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 999 wild Oncorhynchus mykiss and 5,107 wild run O. tshawytscha were PIT tagged during the study period. Rotary screw trap efficiencies averaged 22.3% for juvenile O. tshawytscha and 9.0% for juvenile O. mykiss. Rotary screw traps operated 7 days a week and remote capture operations were conducted when flow and temperature regimes permitted. This is third annual progress report to Bonneville Power Administration for the snorkel surveys conducted in the Entiat River as related to long-term effectiveness monitoring of restoration programs in this watershed. The objective of this study is to monitor the fish habitat utilization of planned in-stream restoration efforts in the Entiat River by conducting pre- and post-construction snorkel surveys at selected treatment and control sites.

Nelle, R.D.

2008-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

Experimental studies of heat and mass exchange in parallel-passage rotary desiccant dehumidifiers for solar cooling applications  

DOE Green Energy (OSTI)

This report presents results of work done to experimentally characterize the performance of rotary desiccant dehumidifiers and to develop and validate analytical methods for evaluating their performance in air-conditioning systems. A facility, the Cyclic Test Facility, and a test-and-analysis procedure were developed to evaluate the performance of the rotary dehumidifiers. Experiments were performed to develop a basic understanding of the simultaneous heat- and mass-transfer processes in the dehumidifiers. Two test articles were tested under cyclic operation to characterize their performance. Detailed accounts of the Cyclic Test Facility, its hardware and instrumentation, the two test articles, and data reduction and analysis methods are provided. The data provide an engineering data base for evaluating rotary desiccant dehumidifiers for cooling applications. 46 refs., 26 figs., 3 tabs.

Bharathan, D.; Parsons, J.M.; Maclaine-cross, I.L.

1987-11-01T23:59:59.000Z

202

Obtaining pressures in the 10?5 Pa range with oil?sealed rotary vacuum pumps  

Science Conference Proceedings (OSTI)

Trapped oil?sealed rotary pumps are usually considered capable of ultimate pressures no lower than about 10?3 Pa. Experiments are described which confirm that most of this residual gas originates from air dissolved in the pump oil. Replacement of the air with a less soluble gas (helium) or an easily trapped gas (carbon dioxide) is shown to give a useful reduction in ultimate pressure and to reduce the oxygen partial pressure to essentially zero. Operation with completely degassed oil is shown to give ultimate pressures in the 10?5 Pa range. The design of pumps based on these principles is discussed.

B. R. F. Kendall

1982-01-01T23:59:59.000Z

203

On the use of the parabolic concentration profile assumption for a rotary desiccant dehumidifier  

SciTech Connect

The current work describes a model for a desiccant dehumidifier which uses a parabolic concentration profile assumption to model the diffusion resistance inside the desiccant particle. The relative merits of the parabolic concentration profile model compared with widely utilized rotary desiccant wheel models are discussed. The periodic steady-state parabolic concentration profile model developed is efficient and can accommodate a variety of materials. These features make it an excellent tool for design studies requiring repetitive desiccant wheel simulations. A quartic concentration profile assumption was also investigated which yielded a 2.8 percent average improvement in prediction error over the parabolic model.

Chant, E.E. [Univ. of Turabo, Gurabo (Puerto Rico); Jeter, S.M. [Georgia Inst. of Technology, Atlanta, GA (United States). George W. Woodruff School of Mechanical Engineering

1995-02-01T23:59:59.000Z

204

Local entropy generation analysis of a rotary magnetic heat pump regenerator  

SciTech Connect

The rotary magnetic heat pump has attractive thermodynamic performance but it is strongly influenced by the effectiveness of the regenerator. This study uses local entropy generation analysis to evaluate the regenerator design and to suggest design improvements. The results show that performance of the proposed design is dominated by heat transfer related entropy generation. This suggests that enhancement concepts that improve heat transfer should be considered, even if the enhancement causes a significant increase in viscous losses (pressure drop). One enhancement technique, the use of flow disrupters, was evaluated and the results showed that flow disrupters can significantly reduce thermodynamic losses.

Drost, M.K.; White, M.D.

1990-04-01T23:59:59.000Z

205

COMPENDIUM OF COMPLETED TESTING IN SUPPORT OF ROTARY MICROFILTRATION AT SAVANNAH RIVER SITE AND HANFORD  

SciTech Connect

This report presents a chronological summary of previous technology development efforts concerning the rotary microfiltration (RMF) unit from SpinTek{trademark}. Rotary microfiltration has been developed for high radiation application over the last decades as one of the optional filtration techniques for supplemental treatment. Supplemental treatment includes a near- or in-tank solids separation and subsequent cesium removal unit, followed by an immobilization technique; this includes options such as steam reforming, bulk vitrification or cast stone (grout). The main difference between RMF and standard cross flow filtration (CFF) is the disconnection of filtrate flux from feed velocity; i.e., filtrate flux is only dependent on transmembrane pressure, filter fouling and temperature. These efforts have been supported by the U.S. Department of Energy (DOE), Office of Cleanup Technologies since the 1990s by their Environmental Management Program (currently EM-31). In order to appropriately address future testing needs, a compilation of the relevant previous testing reports was essential. This compendium does not intend to cover all of the presentations/reports that were produced over the last decades but focuses on those of relevance for developing an RMF unit fit for deployment at the Hanford site. The report is split into three parts: (1) an introductory overview, (2) Figure 1 graphically covering the main development steps and its key players and (3) a more detailed table of the citations and brief descriptions of results and recommendations.

HUBER HJ

2011-05-24T23:59:59.000Z

206

Baseline Design Compliance Matrix for the Rotary Mode Core Sampling System  

SciTech Connect

The purpose of the design compliance matrix (DCM) is to provide a single-source document of all design requirements associated with the fifteen subsystems that make up the rotary mode core sampling (RMCS) system. It is intended to be the baseline requirement document for the RMCS system and to be used in governing all future design and design verification activities associated with it. This document is the DCM for the RMCS system used on Hanford single-shell radioactive waste storage tanks. This includes the Exhauster System, Rotary Mode Core Sample Trucks, Universal Sampling System, Diesel Generator System, Distribution Trailer, X-Ray Cart System, Breathing Air Compressor, Nitrogen Supply Trailer, Casks and Cask Truck, Service Trailer, Core Sampling Riser Equipment, Core Sampling Support Trucks, Foot Clamp, Ramps and Platforms and Purged Camera System. Excluded items are tools such as light plants and light stands. Other items such as the breather inlet filter are covered by a different design baseline. In this case, the inlet breather filter is covered by the Tank Farms Design Compliance Matrix.

LECHELT, J.A.

2000-10-17T23:59:59.000Z

207

Comparison of the performance of open cycle air conditioners utilizing rotary desiccant dehumidifiers  

DOE Green Energy (OSTI)

This paper presents the results of an investigation of open cycle cooling systems using rotary desiccant dehumidifiers. Three systems, the ventilation, recirculation, and Dunkle cycles have been modeled. The performance of these systems coupled with an air-based solar system has been determined using TRNSYS simulations of system operation in four representative US climates. The system COP, fraction of the total cooling load met by the desiccant system, and fraction of the thermal energy provided by solar energy are compared. An assessment of the effect of climate and system parameters on the relative performance of the three system configurations is made. It is shown that in order to meet residential loads of 7 to 11 kW with a COP on the order of unity, systems with high effectiveness must be employed. These systems were also found to perform well when operated solely with a solar thermal input.

Jurinak, J.J.; Beckman, W.A.

1985-01-01T23:59:59.000Z

208

Control schemes for an industrial rotary calciner with a heat shield around the combustion zone  

SciTech Connect

Soda ash (sodium carbonate) is produced by calcining natural trona ore (sodium sesquicarbonate) in rotary calciners. Shell overheating, the consequent deformation of the calciner shell, and heat loss are frequently encountered problems during this operation. Installation of a concentric, metallic heat shield around the calciner`s combustion zone can help to reduce the shell temperature and recover some of the energy that would otherwise be lost. Another problem often encountered is the deterioration of product quality when the system inputs deviate from their design rates. A mathematical model of the calciner with a heat shield is used to design different control schemes in order to maintain the product quality. Performance of the designed control schemes is demonstrated via computer simulation.

Ciftci, S.; Kim, N.K. [Michigan Technological Univ., Houghton, MI (United States). Dept. of Chemical Engineering] [Michigan Technological Univ., Houghton, MI (United States). Dept. of Chemical Engineering

1999-03-01T23:59:59.000Z

209

Method and apparatus for maximizing throughput of indirectly heated rotary kilns  

DOE Patents (OSTI)

An apparatus and method for achieving improved throughput capacity of indirectly heated rotary kilns used to produce pyrolysis products such as shale oils or coal oils that are susceptible to decomposition by high kiln wall temperatures is disclosed. High throughput is achieved by firing the kiln such that optimum wall temperatures are maintained beginning at the point where the materials enter the heating section of the kiln and extending to the point where the materials leave the heated section. Multiple high velocity burners are arranged such that combustion products directly impact on the area of the kiln wall covered internally by the solid material being heated. Firing rates for the burners are controlled to maintain optimum wall temperatures.

Coates, Ralph L; Smoot, L. Douglas; Hatfield, Kent E

2012-10-30T23:59:59.000Z

210

An Advanced Solar-Powered Rotary Solid Adsorption Refrigerator with High Performance  

E-Print Network (OSTI)

In this paper, according to practical consideration, a new solar powered rotary solid adsorption refrigerator system adopting activated carbon fibre + ethanol as its adsorption pair has been designed with higher performance. Moreover, the principle of the refrigeration cycle, different components of the machine, selection of working pairs and feasible theory analysis of the refrigeration system all have been presented in detail. In addition, it shows that the new refrigerator has many great advantages including a simple structure, fast refrigeration, higher thermodynamic coefficient, friendly to the atmospheric environment, etc. This paper explains that the refrigerating process is constant, which has a promising potential for competing the 'intermittent' cycle reported before. Through improving the refrigerant performance of heat and mass transfer in the adsorbent bed, the refrigeration cycle has been advanced from the aspect of utilization of the thermal energy from low-temperature level resources. In addition, it is shown that the commercial solar powered refrigerator will be existent in the near future.

Zheng, A.; Gu, J.

2006-01-01T23:59:59.000Z

211

Stable five axes cryogenic photoemission manipulator without a differentially pumped rotary feedthrough  

Science Conference Proceedings (OSTI)

We report on the design and construction of an ultrahigh vacuum compatible cryogenic manipulator for angle resolved photoemission spectroscopy. Unlike designs that have been used so far, our design allows five motions (three translational and two angular) without a differentially pumped rotary feedthrough. The design greatly reduces the sample motion upon rotation, which is crucial in automatic data acquisition over a large area in the momentum space. The constructed manipulator shows smooth motions in vacuum and the lowest temperature it could reach is about 8 K at the sample position. Angular reproducibilities are found to be about 0.02 deg. for both of the angular motions. The wobbling motion from the rotation around the vertical rotation axis is found to be virtually nonexistent (less than 0.1 mm)

Kim, Bum Joon; Kim, Hyeong-Do; Cho, Deok-Yong; Kim, Myongjin; Oh, S.-J.; Kim, Changyoung [School of Physics and Center for Strongly Correlated Materials Research, Seoul National University, Seoul 151-742 (Korea, Republic of); Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); School of Physics and Center for Strongly Correlated Materials Research, Seoul National University, Seoul 151-742 (Korea, Republic of); Pohang Accelerator Laboratory, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); School of Physics and Center for Strongly Correlated Materials Research, Seoul National University, Seoul 151-742 (Korea, Republic of); Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of)

2005-06-15T23:59:59.000Z

212

Unsteady-state material balance model for a continuous rotary dissolver  

Science Conference Proceedings (OSTI)

The unsteady-state continuous rotary dissolver material balance code (USSCRD) is a useful tool with which to study the performance of the rotary dissolver under a wide variety of operating conditions. The code does stepwise continuous material balance calculations around each dissolver stage and the digester tanks. Output from the code consists of plots and tabular information on the stagewise concentration profiles of UO{sub 2}, PuO{sub 2}, fission products, Pu(NO{sub 3}){sub 4}, UO{sub 2}(NO{sub 3}){sub 2}, fission product nitrates, HNO{sub 3}, H{sub 2}O, stainless steel, total particulate, and total fuel in pins. Other information about material transfers, stagewise liquid volume, material inventory, and dissolution performance is also provided. This report describes the development of the code, its limitations, key operating parameters, usage procedures, and the results of the analysis of several sets of operating conditions. Of primary importance in this work was the estimation of the steady-state heavy metal inventory in a 0.5-t/d dissolver drum. Values ranging from {similar_to}12 to >150 kg of U + Pu were obtained for a variety of operating conditions. Realistically, inventories are expected to be near the lower end of this range. Study of the variation of operating parameters showed significant effects on dissolver product composition from intermittent solids feed. Other observations indicated that the cycle times for the digesters and shear feed should be closely coupled in order to avoid potential problems with off-specification product. 19 references, 14 tables.

Lewis, B.E.

1984-09-01T23:59:59.000Z

213

Carderock Circulating Water Channel | Open Energy Information  

Open Energy Info (EERE)

Circulating Water Channel Circulating Water Channel Jump to: navigation, search Basic Specifications Facility Name Carderock Circulating Water Channel Overseeing Organization United States Naval Surface Warfare Center Hydrodynamic Testing Facility Type Channel Length(m) 18.3 Beam(m) 6.7 Depth(m) 2.7 Water Type Freshwater Cost(per day) Contact POC Special Physical Features The Circulating Water Channel is a vertical plane, open to the atmosphere test section with a free surface in a closed recirculating water circuit, variable speed, rectangular cross-sectional shape facility. There are 10 large viewing windows on either side of the test section at different elevations and 9 in the bottom; movable bridge spans the test section for ease and versatility in mounting models, rigging bridge is capable of taking towing loads at any one of numerous points up to 35,584 N

214

EPRI Clean Water Act 316(b) Fish Protection Technology Workshop Proceedings: September 30, 2004, Holden, Massachusetts  

Science Conference Proceedings (OSTI)

This compact disc (CD) contains presentations made at the EPRI Clean Water Act §316(b) Fish Protection Technology Workshop held at the facilities of Alden Research Laboratory in Holden, Massachusetts on September 30, 2004. The presentations provide engineering and visual information on many types of cooling water intake structure fish protection technologies, including barrier nets, behavioral barriers (strobe lights and acoustic systems), traveling water screens, rotary screens, flat panel and cyli...

2004-12-27T23:59:59.000Z

215

DSP-Based Sensor-less Permanent Magnet Synchronous Motor Driver With Quasi-Sine PWM for Air-Conditioner Rotary Compressor.  

E-Print Network (OSTI)

??This thesis presented a sensor-less permanent magnet synchronous motor (PMSM) driver for controlling air-conditioner rotary compressor speed. In this thesis, a quasi-sine pulse-width modulation (PWM)… (more)

Liu, Li-hsiang

2012-01-01T23:59:59.000Z

216

Coal desulfurization in a rotary kiln combustor. Quarterly report No. 1, April 16, 1990--July 15, 1990  

Science Conference Proceedings (OSTI)

BCR National Laboratory (BCRNL) has initiated a project aimed at evaluating the technical and economic feasibility of using a rotary kiln, suitably modified, to burn Pennsylvania anthracite wastes, co-fired with high-sulfur bituminous coal. Limestone will be injected into the kiln for sulfur control, to determine whether high sulfur capture levels can be achieved with high sorbent utilization. The principal objectives of this work are: (1) to prove the feasibility of burning anthracite refuse, with co-firing of high-sulfur bituminous coal and with limestone injection for sulfur emissions control, in a rotary kiln fitted with a Universal Energy International (UEI) air injector system; (2) to determine the emissions levels of SO{sub x} and NO{sub x} and specifically to identify the Ca/S ratios that are required to meet New Source Performance Standards; (3) to evaluate the technical and economic merits of a commercial rotary kiln combustor in comparison to fluidized bed combustors; and, (4) to ascertain the need for further work, including additional combustion tests, prior to commercial application, and to recommend accordingly a detailed program towards this end.

Cobb, J.T. Jr.

1990-08-15T23:59:59.000Z

217

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter specifies the design and inspection requirements for personnel lift platforms as well as the operational requirements for such platforms and appurtenant hoisting equipment. It implements the requirements of ASME B30.23, Personnel Lifting Systems (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 4.1 GENERAL ................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1

218

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Change Notice No. 1 DOE-STD-1090-2007 Change Notice No. 1 DOE-STD-1090-2007 December 2007 Chapter 4 Provide ASME attribution at introduction to the Table on Contents and on Figures 4-3,4 and Exhibits 1 & 2 Chapter 7 Provide ASME attribution at introduction to the Table on Contents and on Figures 7-1,2,3,4,5 and Table 7-1 Chapter 8 Provide ASME attribution at introduction to the Table on Contents and on Figures 8-1,2,3,4,5,6,7,8,9 and Table 8-1 Chapter 9 Provide ASME attribution at introduction to the Table on Contents and on Figures 9-1,2,3,4,5,6 and Table 9-2 Chapter 11 Provide ASME attribution at introduction to the Table on Contents and on Figures 11-10,15 and Tables 11-10,11,14,15,16 Chapter 12 Provide ASME attribution at introduction to the Table on Contents and on

219

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

220

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")] (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 7.1 GENERAL .................................................................................................................................7-1 7.1.1 Operator Training/Qualification

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 9 MOBILE CRANES 9-i This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes") (for latest ASME standards, see http://catalog.asme.org/home.cfm?Category=CS). 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

222

rig upgrades2.qxp  

NLE Websites -- All DOE Office Websites (Extended Search)

D E T I N U S O F A M E R I C A E A s the oil and gas industry continues to drill in more remote areas, at deeper depths, and in more challenging environments, the advancement of...

223

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A frames (sometimes referred to as portable gantries), Truck mounted cranes with a capacity of 1 ton or less not covered in ASME B30.5 (.Mobile and Locomotive Cranes.) and self...

224

Hoisting and Rigging  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Four-pad pow ered vacuum lifting device Four-pad pow ered vacuum lifting device manipulator DOE-STD-1090-2007 14.3 VACUUM LIFTING DEVICES 14-11 Chapter 14 Below-the-Hook...

225

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method of destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500.degree. C. to heat the particulate material to a temperature in the range of from about 200.degree. C. to about 900.degree. C. in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, Michael J. (Bolingbrook, IL); Arzoumanidis, Gregory G. (Naperville, IL)

1997-01-01T23:59:59.000Z

226

Method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet. 5 figs.

McIntosh, M.J.; Arzoumanidis, G.G.

1997-09-02T23:59:59.000Z

227

Apparatus and methods for cooling and sealing rotary helical screw compressors  

DOE Patents (OSTI)

In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor center lines or alternatively the channel paths coincide with the helical path of the rotor edges. 14 figs.

Fresco, A.N.

1997-08-05T23:59:59.000Z

228

Apparatus and methods for cooling and sealing rotary helical screw compressors  

DOE Patents (OSTI)

In a compression system which incorporates a rotary helical screw compressor, and for any type of gas or refrigerant, the working liquid oil is atomized through nozzles suspended in, and parallel to, the suction gas flow, or alternatively the nozzles are mounted on the suction piping. In either case, the aim is to create positively a homogeneous mixture of oil droplets to maximize the effectiveness of the working liquid oil in improving the isothermal and volumetric efficiencies. The oil stream to be atomized may first be degassed at compressor discharge pressure by heating within a pressure vessel and recovering the energy added by using the outgoing oil stream to heat the incoming oil stream. The stripped gas is typically returned to the compressor discharge flow. In the preferred case, the compressor rotors both contain a hollow cavity through which working liquid oil is injected into channels along the edges of the rotors, thereby forming a continuous and positive seal between the rotor edges and the compressor casing. In the alternative method, working liquid oil is injected either in the same direction as the rotor rotation or counter to rotor rotation through channels in the compressor casing which are tangential to the rotor edges and parallel to the rotor centerlines or alternatively the channel paths coincide with the helical path of the rotor edges.

Fresco, Anthony N. (P.O. Box 734, Upton, NY 11973)

1997-01-01T23:59:59.000Z

229

Independent one-way acting hydraulic jar sections for a rotary drill string  

SciTech Connect

First and second separate one-way acting hydraulic jar sections each include inner and outer telescopically arranged tubular members with means for connecting one end of each the inner and outer tubular members of each jar section in the drill string. Spaced seal means between the inner and outer tubular members form a chamber in each jar section for confining hydraulic operating fluid. Hydraulic jar means are formed by cooperating means on the inner and outer tubular members within each operating fluid chamber. The cooperating means is spaced axially and disengaged in each fluid chamber when the drill string is in tension and compression during rotary drilling operation to inhibit damage and wear thereto. The hydraulic jar means in the first jar section is constructed to deliver an up jar and the jar means in the separate second jar section is constructed to deliver a down jar to the drill string. Drive means in a sealed chamber in each jar section connect the inner and outer tubular members of each jar section to allow relative longitudinal movement while preventing relative rotation therebetween. Means to equalize pressure adjacent one end of each of the chambers with the pressure in the well bore is provided in each jar section, which accommodates relative longitudinal movement of the inner and outer tubular members of each jar section for selectively creating an up or down jarring force independently of the well bore pressure.

Anderson, E.A.; Webb, D.D.

1980-10-07T23:59:59.000Z

230

A method and system including a double rotary kiln pyrolysis or gasification of waste material  

DOE Patents (OSTI)

A method is described for destructively distilling an organic material in particulate form wherein the particulates are introduced through an inlet into one end of an inner rotating kiln ganged to and coaxial with an outer rotating kiln. The inner and outer kilns define a cylindrical annular space with the inlet being positioned in registry with the axis of rotation of the ganged kilns. During operation, the temperature of the wall of the inner rotary kiln at the inlet is not less than about 500 C to heat the particulate material to a temperature in the range of from about 200 C to about 900 C in a pyrolyzing atmosphere to reduce the particulate material as it moves from the one end toward the other end. The reduced particulates including char are transferred to the annular space between the inner and the outer rotating kilns near the other end of the inner rotating kiln and moved longitudinally in the annular space from near the other end toward the one end in the presence of oxygen to combust the char at an elevated temperature to produce a waste material including ash. Also, heat is provided which is transferred to the inner kiln. The waste material including ash leaves the outer rotating kiln near the one end and the pyrolysis vapor leaves through the particulate material inlet.

McIntosh, M.J.; Arzoumanidis, G.G.

1995-12-31T23:59:59.000Z

231

EVALUATION OF ALTERNATIVE FILTER MEDIA FOR THE ROTARY MICROFILTER, PHASE 2  

SciTech Connect

Testing was conducted at the Savannah River National Laboratory (SRNL) to investigate filter membrane performance in an effort to increase rotary microfilter (RMF) throughput. Membranes were tested in the SpinTek Filtration, Inc. Static Test Cell (STC), which permitted quick and easy testing of several different membranes. Testing consisted of 100 hours tests with two different slurry feeds, based on recommendations from the phase 1 testing. One feed contained Monosodium Titanate (MST) solids in a simulated salt solution. The other feed contained simulated sludge batch 6 (SB6) solids in a simulated salt solution. Five membranes were tested, one each from filter manufactures Pall and Porvair and three from the Oak Ridge National Laboratory (ORNL). The membrane from Pall is the current membrane used on the latest generation RMF. The Porvair membrane performed well in previous STC tests as well as one of the ORNL membranes. The other two membranes from ORNL were recently developed and not available for the previous STC test. The results indicate that the Porvair filter performed best with the MST slurry and the ORNL SVB6-1B filter performed best with the SB6 slurry. Difficulty was encountered with the ORNL filters due to their dimensional thickness, which was greater than the recommended filter thickness for the STC. The STC equipment was modified to complete the testing of the ORNL filters.

Fowley, M.

2012-07-31T23:59:59.000Z

232

U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Reserves 2006 ...  

U.S. Energy Information Administration (EIA)

... and the Average Number of Active Rotary Drilling Rigs, 1977-2006: PDF: 4: ... Glossary: A listing of terms used within the Reserves Report, and their ...

233

U.S. Crude Oil, Natural Gas, and Natural Gas Liquids Reserves 2005 ...  

U.S. Energy Information Administration (EIA)

... and the Average Number of Active Rotary Drilling Rigs, 1977-2005: PDF: 4: ... Glossary: A listing of terms used within the Reserves Report, and their ...

234

Crude Oil and Natural Gas Drilling Activity  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Rotary rigs in operation ...

235

Crude Oil and Natural Gas Drilling Activity  

U.S. Energy Information Administration (EIA)

-No Data Reported; --= Not Applicable; NA = Not Available; W = Withheld to avoid disclosure of individual company data. Notes: Rotary rigs in ...

236

Performance investigation on a novel two-stage solar driven rotary desiccant cooling system using composite desiccant materials  

Science Conference Proceedings (OSTI)

In this study, a two-stage solar driven rotary desiccant cooling (TSRDC) system with novel configuration and newly developed silica gel-haloid composite desiccant is proposed aiming to reduce regeneration temperature and to achieve high energy performance. Simulated results show that there also exists an optimal rotation speed for TSRDC system. Compared with one-stage system, it is found that for the similar supply air state, the required regeneration temperature of TSRDC system is lower and for the same regeneration temperature, the cooling capacity of TSRDC is bigger. (author)

Ge, T.S.; Li, Y.; Dai, Y.J.; Wang, R.Z. [Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University, Shanghai 200240 (China)

2010-02-15T23:59:59.000Z

237

Analysis of the Energy-Saving Potential of a Three-Rotary Wheel Fresh Air-Handling Unit  

E-Print Network (OSTI)

To evaluate the energy-saving potential of a proposed three-rotary wheel fresh air-handling unit (TRWFAHU), it is numerically simulated with weather data of Changsha by using a mathematical model. Compared with a conventional fresh air-handling unit, TRWFAHU can save 10.2% of primary energy and greatly decrease the energy consumption of chiller. If waste heat is available for regenerating the desiccant, the system can achieve greater energy savings. It is feasible to improve indoor air quality (IAQ) by increasing ventilation while without increasing energy consumption.

Hao, X.; Zhang, G.; Zou, S.; Liu, H.

2006-01-01T23:59:59.000Z

238

Integrated Status and Effectiveness Monitoring Program - Entiat River Rotary Screw Traps,Snorkel Surveys, and Steelhead Redd Surveys, 2008.  

DOE Green Energy (OSTI)

The USFWS Mid-Columbia River Fishery Resource Office (MCRFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program from March through November of 2008. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 16,782 wild salmonids were PIT tagged during the study period. Of this, 3,961(23.6%) were wild Oncorhynchus mykiss, 6,987 (41.6%) were wild spring run O. tshawytscha, and 5,591 (33.3%) were identified as wild O. tshawytscha of unknown run. Rotary screw trap efficiencies averaged 40.3% at the upper (Rkm 11.0) trap and 7.8% for the lower (Rkm 2.0) trap. These efficiencies were pooled for emigrant O. tshawytscha and O. mykiss. The MCRFRO conducted effectiveness monitoring snorkel surveys at 24 sites during the winter period and 30 sites during the summer and fall periods of 2008 as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. The 2008 steelhead spawning grounds surveys were conducted weekly in the main Entiat River from rkm 1.1 to 44.2. A total of 222 steelhead redds were identified over the period from February 28 to June 16 2008 with April being the peak spawning month. Approximately 80% of the steelhead redds were located downstream of the rkm 26.

Nelle, R.D.; Desgroseiller, Tom; Cotter, Michael (U.S. Fish and Wildlife Service)

2009-02-17T23:59:59.000Z

239

Integrated Status and Effectiveness Monitoring Program - Entiat River Rotary Screw Traps, Snorkel Surveys, and Steelhead Redd Surveys, 2008-2009.  

DOE Green Energy (OSTI)

The USFWS Mid-Columbia River Fishery Resource Office (MCRFRO) operated two rotary screw traps on the Entiat River as part of the Integrated Status and Effectiveness Monitoring Program from March through November of 2008. Along with the smolt traps, juvenile emigrants were also captured at remote locations throughout the Entiat watershed and its major tributary, the Mad River. A total of 16,782 wild salmonids were PIT tagged during the study period. Of this, 3,961(23.6%) were wild Oncorhynchus mykiss, 6,987 (41.6%) were wild spring run O. tshawytscha, and 5,591 (33.3%) were identified as wild O. tshawytscha of unknown run. Rotary screw trap efficiencies averaged 40.3% at the upper (Rkm 11.0) trap and 7.8% for the lower (Rkm 2.0) trap. These efficiencies were pooled for emigrant O. tshawytscha and O. mykiss. The MCRFRO conducted effectiveness monitoring snorkel surveys at 24 sites during the winter period and 30 sites during the summer and fall periods of 2008 as part of the Integrated Status and Effectiveness Monitoring Program in the Entiat River. The 2008 steelhead spawning grounds surveys were conducted weekly in the main Entiat River from rkm 1.1 to 44.2. A total of 222 steelhead redds were identified over the period from February 28 to June 16 2008 with April being the peak spawning month. Approximately 80% of the steelhead redds were located downstream of the rkm 26.

Nelle, R.D.; Desgroseillier, Tom; Cotter, Michael [U.S. Fish and Wildlife Service

2009-04-14T23:59:59.000Z

240

EVALUATION OF SUPPLEMENTAL PRE-TREATMENT DEVELOPMENT REQUIREMENTS TO MEET TRL 6 ROTARY MICROFILTRATION  

SciTech Connect

In spring 2011, the Technology Maturation Plan (TMP) for the Supplemental Treatment Project (RPP-PLAN-49827, Rev. 0), Technology Maturation Plan for the Treatment Project (T4S01) was developed. This plan contains all identified actions required to reach technical maturity for a field-deployable waste feed pretreatment system. The supplemental pretreatment system has a filtration and a Cs-removal component. Subsequent to issuance of the TMP, rotary microfiltration (RMF) has been identified as the prime filtration technology for this application. The prime Cs-removal technology is small column ion exchange (ScIX) using spherical resorcinol formaldehyde (sRF) as the exchange resin. During fiscal year 2011 (FY2011) some of the tasks identified in the TMP have been completed. As of September 2011, the conceptual design package has been submitted to DOE as part of the critical decision (CD-1) process. This document describes the remaining tasks identified in the TMP to reach technical maturity and evaluates the validity of the proposed tests to fill the gaps as previously identified in the TMP. The potential vulnerabilities are presented and the completed list of criteria for the DOE guide DOE G 413.3-4 different technology readiness levels are added in an attachment. This evaluation has been conducted from a technology development perspective - all programmatic and manufacturing aspects were excluded from this exercise. Compliance with the DOE G 413.3-4 programmatic and manufacturing requirements will be addressed directly by the Treatment Project during the course of engineering design. The results of this evaluation show that completion of the proposed development tasks in the TMP are sufficient to reach TRL 6 from a technological point of view. The tasks involve actual waste tests using the current baseline configuration (2nd generation disks, 40 psi differential pressure, 30 C feed temperature) and three different simulants - the PEP, an AP-Farm and an S-saltcake. Based on FY2011 dollars used in the TMP, these tests will have ROM costs of $950K and require up to 10 months to complete. Completion of the simulant testing will satisfy the TRL 5 and TRL 6 criteria that are related to system testing with materials that represent the full range of properties in a relevant environment.

HUBER HJ

2011-10-03T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Evaluation of rotary drum screens used to protect juvenile salmonids in the Yakima River Basin, Washington, USA  

DOE Green Energy (OSTI)

The purpose of this study is to assess the design and operation of rotary drum screens. Chinook salmon Oncorhynchus tshawytscha and steelhead O. mykiss are the potentially affected fish. Cold-branded fish are released upstream of the screen facilities. For descaling tests, the fish are captured as they exit the facility and are examined for injuries, descaling, and post-test mortalities. For screen passage tests, nets are placed in the irrigation ditch, downstream of the screen facilities, to determine if fish can pass through or over the screens. More than 100 tests have been conducted with almost 35,000 fish. Additionally, nearly 2000 native fish have been evaluated. Usually less than 2% of the test fish are injured or dead, and the condition of test fish does not differ from the controls. Less than 2% of the fish pass through or over the screens when the screen seals are properly installed and maintained.

Neitzel, D.A.; Abernethy, C.S. (Pacific Northwest Lab., Richland, WA (USA)); Clune, T.J. (USDOE Bonneville Power Administration, Yakima, WA (USA))

1990-10-01T23:59:59.000Z

242

SERI Desiccant Cooling Test Facility. Status report. Preliminary data on the performance of a rotary parallel-passage silica-gel dehumidifier  

DOE Green Energy (OSTI)

This report describes the SERI Desiccant Cooling Test Facility. The facility can test bench-scale rotary dehumidifiers over a wide range of controlled conditions. We constructed and installed in the test loop a prototype parallel-passage rotary dehumidifier that has spirally wound polyester tape coated with silica gel. The initial tests gave satisfactory results indicating that approximately 90% of the silica gel was active and the overall Lewis number of the wheel was near unity. The facility has several minor difficulties including an inability to control humidity satisfactorily and nonuniform and highly turbulent inlet velocities. To completely validate the facility requires a range of dehumidifier designs. Several choices are available including constructing a second parallel-passage dehumidifier with the passage spacing more uniform.

Schultz, K.J.

1986-04-01T23:59:59.000Z

243

Apparatus and method for controlling the rotary airlocks in a coal processing system by reversing the motor current rotating the air lock  

SciTech Connect

An improvement to a coal processing system where hard materials found in the coal may cause jamming of either inflow or outflow rotary airlocks, each driven by a reversible motor. The instantaneous current used by the motor is continually monitored and compared to a predetermined value. If an overcurrent condition occurs, indicating a jamming of the airlock, a controller means starts a "soft" reverse rotation of the motor thereby clearing the jamming. Three patterns of the motor reversal are provided.

Groombridge, Clifton E. (Hardin, MT)

1996-01-01T23:59:59.000Z

244

Investigation of a rotary valving system with variable valve timing for internal combustion engines: Final technical report  

DOE Green Energy (OSTI)

The objective of the program was to provide a functional demonstration of the Hansen Rotary Valving System with Variable Valve timing (HRVS/VVT), capable of throttleless inlet charge control, as an alternative to conventional poppet-valves for use in spark ignited internal combustion engines. The goal of this new technology is to secure benefits in fuel economy, broadened torque band, vibration reduction, and overhaul accessibility. Additionally, use of the variable valve timing capability to vary the effective compression ratio is expected to improve multi-fuel tolerance and efficiency. Efforts directed at the design of HRVS components proved to be far more extensive than had been anticipated, ultimately requiring that proof-trial design/development work be performed. Although both time and funds were exhausted before optical or ion-probe types of in-cylinder investigation could be undertaken, a great deal of laboratory data was acquired during the course of the design/development work. This laboratory data is the basis for the information presented in this Final Report.

Cross, P.C.; Hansen, C.N.

1994-11-18T23:59:59.000Z

245

Build a Floating Oil Rig  

Energy.gov (U.S. Department of Energy (DOE))

The U.S. Department of the Interior's Minerals Management Service developed this teacher's guide about the many energy resources found in, over, and under the ocean. Includes sections on petroleum,...

246

Well servicing rig market report  

Science Conference Proceedings (OSTI)

This article profiles the well servicing industry, focusing on the problems facing the industry under currently depressed market conditions. The problems of rising operating costs, oil price uncertainty, and aging equipment are addressed specifically.

Killalea, M

1989-01-01T23:59:59.000Z

247

Enumeration of Juvenile Salmonids in the Okanogan Basin Using Rotary Screw Traps, Performance Period: March 15, 2006 - July 15, 2006.  

DOE Green Energy (OSTI)

The Colville Tribes identified the need for collecting baseline census data on the timing and abundance of juvenile salmonids in the Okanogan River basin for the purpose of documenting local fish populations, augmenting existing fishery data and assessing natural production trends of salmonids. This report documents and assesses the pilot year of rotary trap capture of salmonid smolts on the Okanogan River. The project is a component of the Colville Tribes Okanogan Basin Monitoring and Evaluation Program (OBMEP) which began in 2004. Trapping for outmigrating fish began on 14 March 2006 and continued through 11 July 2006. Anadromous forms of Oncorhynchus, including summer steelhead (O. mykiss), Chinook (O. tshawytscha), and sockeye (O. nerka), were targeted for this study; all have verified, natural production in the Okanogan basin. Both 8-ft and 5-ft rotary screw traps were deployed on the Okanogan River from the Highway 20 Bridge and typically fished during evening hours or 24 hours per day, depending upon trap position and discharge conditions. Juvenile Chinook salmon were the most abundant species trapped in 2006 (10,682 fry and 2,024 smolts), followed by sockeye (205 parr and 3,291 smolts) and steelhead (1 fry and 333 smolts). Of the trapped Chinook, all fry were wild origin and all but five of the smolts were hatchery-reared. All trapped sockeye were wild origin and 88% of the steelhead smolts were hatchery-reared. Mark-recapture experiments were conducted using Chinook fry and hatchery-reared steelhead smolts (sockeye were not used in 2006 because the peak of the juvenile migration occurred prior to the onset of the mark-recapture experiments). A total of 930 chinook fry were marked and released across eight separate release dates (numbers of marked Chinook fry released per day ranged from 34 to 290 fish). A total of 11 chinook fry were recaptured for an overall trap efficiency of 1.18%. A total of 710 hatchery-reared steelhead were marked and released across three separate release dates (numbers of steelhead released per day ranged from 100 to 500 fish). A total of 12 steelhead were recaptured for an overall trap efficiency of 1.69%. A pooled Peterson estimator with a Chapman modification was used to produce population estimates for wild Chinook fry and hatchery-reared steelhead based on the results of the mark-recapture experiments. The 2006 populations for Chinook and steelhead were estimated to be 381,554 (95% confidence intervals: 175,731-587,377) and 14,164 (6,999-21,330), respectively. The population estimates were based on the periods in which mark-recapture experiments were initialized through the end of the trapping season (10 May for steelhead and 1 June for Chinook).

Johnson, Peter N.; Rayton, Michael D.

2007-05-01T23:59:59.000Z

248

Development of a cable reel development system using a rotary joint for kilometer lengths of two-fiber multi-mode fiber optic cable  

SciTech Connect

Brookhaven National Laboratory (BNL) recently developed a two-component system for use during remote inspections. The system consists of a mobile unit with television cameras and other equipment and a stationary base station. A variety of signals must be continually transmitted between the two system components as the mobile unit is moved from the location to another. Two channels of broadband (10MHz) NTSC video are transmitted from the mobile unit to the base station, and a bi-directional ``talk set`` provides audio communication between personnel at each location. In addition, several channels of RS-232 are required to support present and future instruments used at the mobile unit and controlled by personnel at the base station. Brookhaven developed a mobile unit which communicated with a base station over a 2-fiber multimode fiber optic cable. One of the design requirements was maintaining constant communication with the base station during the time the mobile unit was moved about. To provide uninterrupted communications, deployment of the 1-km long fiber optic cable was initially performed with a ``spinning reel`` mechanism. The spinning reel mechanism proved to be mechanically unsuitable, and so the cable deployment mechanism was redesigned to spool the cable off the reel. The requirement for uninterrupted communications required a two-channel fiber optic rotary joint in the design. Incorporation of the rotary joint into the design is described, and appropriate reference material is included.

Curtiss, J.A.; Jahelka, J.R.

1995-08-11T23:59:59.000Z

249

A safety assessment of rotary mode core sampling in flammable gas single shell tanks: Hanford Site, Richland, Washington  

SciTech Connect

This safety assessment (SA) addresses each of the required elements associated with the installation, operation, and removal of a rotary-mode core sampling (RMCS) device in flammable-gas single-shell tanks (SSTs). The RMCS operations are needed in order to retrieve waste samples from SSTs with hard layers of waste for which push-mode sampling is not adequate for sampling. In this SA, potential hazards associated with the proposed action were identified and evaluated systematically. Several potential accident cases that could result in radiological or toxicological gas releases were identified and analyzed and their consequences assessed. Administrative controls, procedures and design changes required to eliminate or reduce the potential of hazards were identified. The accidents were analyzed under nine categories, four of which were burn scenarios. In SSTS, burn accidents result in unacceptable consequences because of a potential dome collapse. The accidents in which an aboveground burn propagates into the dome space were shown to be in the ``beyond extremely unlikely`` frequency category. Given the unknown nature of the gas-release behavior in the SSTS, a number of design changes and administrative controls were implemented to achieve these low frequencies. Likewise, drill string fires and dome space fires were shown to be very low frequency accidents by taking credit for the design changes, controls, and available experimental and analytical data. However, a number of Bureau of Mines (BOM) tests must be completed before some of the burn accidents can be dismissed with high confidence. Under the category of waste fires, the possibility of igniting the entrapped gases and the waste itself were analyzed. Experiments are being conducted at the BOM to demonstrate that the drill bit is not capable of igniting the trapped gas in the waste. Laboratory testing and thermal analysis demonstrated that, under normal operating conditions, the drill bit will not create high enough temperatures to initiate a propagating reaction in the waste. However, system failure that coincides in a waste layer with high organic content and low moisture may initiate an exothermic reaction in the waste. Consequently, a conservative approach based on the current state of the knowledge resulted in limiting the drilling process to a subset of the flammable-gas tanks. Accidents from the chemical reactions and criticality category are shown to result in acceptable risk. A number of accidents are shown to potentially result in containment (tank liner) breach below the waste level. Mitigative features are provided for these accidents. Gas-release events without burn also are analyzed, and radiological and toxicological consequences are shown to be within risk guidelines. Finally, the consequences of potential spills are shown to be within the risk guidelines.

Raymond, R.E.

1996-04-15T23:59:59.000Z

250

Rotary bulk solids divider  

DOE Patents (OSTI)

An apparatus for the disbursement of a bulk solid sample comprising, a gravity hopper having a top open end and a bottom discharge end, a feeder positioned beneath the gravity hopper so as to receive a bulk solid sample flowing from the bottom discharge end, and a conveyor receiving the bulk solid sample from the feeder and rotating on an axis that allows the bulk solid sample to disperse the sample to a collection station.

Maronde, Carl P. (McMurray, PA); Killmeyer, Jr., Richard P. (Pittsburgh, PA)

1992-01-01T23:59:59.000Z

251

Rotary drilling jar  

SciTech Connect

This patent describes an improved jar for use in freeing well tools and the like stuck in a well bore. The improvement comprises: tubular, inner mandrel means having a downwardly facing shoulder and having an annular groove in an exterior surface located relatively below the shoulder. The annular groove in the inner mandrel means tapers inwardly from an exterior surface of the inner mandrel means. The inner mandrel means are arranged for connection to a conduit when positioned in the well bore; and tubular, outer mandrel means encircling the inner mandrel means and arranged at a lower end for connection to the well to tool and having an upwardly facing abutment engageable with the downwardly facing shoulder.

Loeb, J.B.; Osborne, A.J.; Miglierini, R.A.

1987-05-05T23:59:59.000Z

252

Rotary slot dog  

SciTech Connect

A clamp or dog is disclosed which preferably comprises a slotted stepped cylindrical body which is inserted into a hole in a workpiece and then fastened to a base or fixture using a screw which is inserted through the slot. The stepped configuration provides an annular clamping surface which securely clamps the workpiece against the base or fixture. The slotted cylindrical configuration permits adjustment of the workpiece and retaining clamp in any direction, i.e., over 360.degree., relative to the mounting position of the screw in the base or fixture.

Cutburth, Ronald W. (Tracy, CA); Smauley, David A. (Livermore, CA)

1987-01-01T23:59:59.000Z

253

Plan for support of large-plant (post-CRBR) needs in large-leak sodium-water reaction area  

SciTech Connect

Work in the large leak test and analysis area of steam generator development has been carried out at GE-ARSD under 189a SG037 since 1973. The currently planned master schedule for the SG037 program is shown. Principal activities are the large leak testing program being carried out at the Large Leak Test Rig and the analysis methods development. The plan for supporting the large plant (post-CRBR) needs in the large leak sodium-water reaction area is outlined. Most of the needs will be answered in the current SG037 large leak program. (DLC)

Whipple, J.C.

1980-03-01T23:59:59.000Z

254

Water Quality  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Quality Water Quality We protect water quality through stormwater control measures and an extensive network of monitoring wells and stations encompassing groundwater, surface...

255

Turbid water Clear water  

E-Print Network (OSTI)

: The submersible laser bathymetric (LBath) optical system is capable of simultaneously providing visual images- dynamical wing. This underwater package is pulled through the water by a single towed cable with fiber optic special high energy density optical fibers. A remote Pentium based PC also at the surface is used

Jaffe, Jules

256

Water Intoxication  

E-Print Network (OSTI)

2008, May 14). Too much water raises seizure risk in babies.id=4844 9. Schoenly, Lorry. “Water Intoxication and Inmates:article/246650- overview>. 13. Water intoxication alert. (

Lingampalli, Nithya

2013-01-01T23:59:59.000Z

257

Pharmaceutical Waters  

Science Conference Proceedings (OSTI)

Table 3   Water treatment process for water for injection (WFI)...deionization WFI production Evaporation still or vapor compression...

258

Water Snakes  

NLE Websites -- All DOE Office Websites (Extended Search)

of Cook County George W. Dunne, President Roland F. Eisenbeis, Supt. of Conservation WATER SNAKES Contrary to popular belief, the Water Moccasin commonly known as the...

259

Investigating Water  

E-Print Network (OSTI)

This 3-ring binder contains teaching plans for 12 lessons on topics such as "Water in Our Daily Lives," "The Water Cycle," "Amazing Aquifers," "Water and Soil," "Aquatic Ecosystems," and "Water Wise Use." Accompanying each lesson plan are activity and record sheets for hands-on learning experiences. This curriculum is intended for students in about 4th to 8th grades.

Howard Jr., Ronald A.

2002-01-02T23:59:59.000Z

260

Energy Basics: Water Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

Storage Water Heaters Tankless Demand Water Heaters Heat Pump Water Heaters Solar Water Heaters Tankless Coil & Indirect Water Heaters Water Heating A variety of...

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

High-Temperature-Turbine Technology Program: Phase II. Technology test and support studies. Design and development of the liquid-fueled high-temperature combustor for the Turbine Spool Technology Rig  

SciTech Connect

The concept selected by Curtiss-Wright for this DOE sponsored High Temperature Turbine Technology (HTTT) Program utilizes transpiration air-cooling of the turbine subsystem airfoils. With moderate quantities of cooling air, this method of cooling has been demonstrated to be effective in a 2600 to 3000/sup 0/F gas stream. Test results show that transpiration air-cooling also protects turbine components from the aggressive environment produced by the combustion of coal-derived fuels. A new single-stage, high work transpiration air-cooled turbine has been designed and fabricated for evaluation in a rotating test vehicle designated the Turbine Spool Technology Rig (TSTR). The design and development of the annular combustor for the TSTR are described. Some pertinent design characteristics of the combustor are: fuel, Jet A; inlet temperature, 525/sup 0/F; inlet pressure, 7.5 Atm; temperature rise, 2475/sup 0/F; efficiency, 98.5%; exit temperature pattern, 0.25; and exit mass flow, 92.7 pps. The development program was conducted on a 60/sup 0/ sector of the full-round annular combustor. Most design goals were achieved, with the exception of the peak gas exit temperature and local metal temperatures at the rear of the inner liner, both of which were higher than the design values. Subsequent turbine vane cascade testing established the need to reduce both the peak gas temperature (for optimum vane cooling) and the inner liner metal temperature (for combustor durability). Further development of the 60/sup 0/ combustor sector achieved the required temperature reductions and the final configuration was incorporated in the TSTR full-annular burner.

1981-06-01T23:59:59.000Z

262

Ground Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Nature Bulletin No. 408-A February 27, 1971 Forest Preserve District of Cook County George W. Dunne, President Roland F. Eisenbeis, Supt. of Conservation GROUND WATER We take...

263

Water Dogs  

NLE Websites -- All DOE Office Websites (Extended Search)

NA Question: I'd like to know about the water dogs and their life cycle? Replies: Water dog, or mud puppy, is a common name for a type of salamander that never develops lungs, but...

264

Water Bugs  

NLE Websites -- All DOE Office Websites (Extended Search)

Bugs Bugs Nature Bulletin No. 221-A March 12, 1966 Forest Preserve District of Cook County Seymour Simon, President Roland F. Eisenbeis, Supt. of Conservation WATER BUGS It is fascinating to lie in a boat or on a log at the edge of the water and watch the drama that unfolds among the small water animals. Among the star performers in small streams and ponds are the Water Bugs. These are aquatic members of that large group of insects called the "true bugs", most of which live on land. Moreover, unlike many other types of water insects, they do not have gills but get their oxygen directly from the air. Those that do go beneath the surface usually carry an oxygen supply with them in the form of a shiny glistening sheath of air imprisoned among a covering of fine waterproof hairs. The common water insect known to small boys at the "Whirligig Bug" is not a water bug but a beetle.

265

EXTENSION WATER SUMMIT PRIORITY: WATER CONSERVATION  

E-Print Network (OSTI)

EXTENSION WATER SUMMIT PRIORITY: WATER CONSERVATION Leadership Team Subcommittee: Joan Bradshaw Michael Dukes Pierce Jones Kati Migliaccio #12;Water Conservation - Situation · Florida water supplies;Water Conservation Initiative 2: Enhancing and protecting water quality, quantity, and supply Priority 1

Slatton, Clint

266

Reusing Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Reusing Water Reusing Water Reusing Water Millions of gallons of industrial wastewater is recycled at LANL by virtue of a long-term strategy to treat wastewater rather than discharging it into the environment. April 12, 2012 Water from cooling the supercomputer is release to maintain a healthy wetland. Contact Environmental Communication & Public Involvement P.O. Box 1663 MS M996 Los Alamos, NM 87545 (505) 667-0216 Email We reuse the same water up to six times before releasing it back into the environment cleaner than when it was pumped. How many times does LANL reuse water? Wastewater is generated from some of the facilities responsible for the Lab's biggest missions, such as the cooling towers of the Los Alamos Neutron Science Center, one of the Lab's premier science research

267

Water Analysis  

NLE Websites -- All DOE Office Websites (Extended Search)

- National Energy Technology Laboratory Office of Systems Analyses and Planning EUEC Energy & Environment Conference 2008, EPS,1292008 2 * Water Scarcity Seen Dampening Case...

268

Natural Gas - U.S. Energy Information Administration (EIA) - U.S. Energy  

Gasoline and Diesel Fuel Update (EIA)

23, 2012 | Release Date: May 24, 23, 2012 | Release Date: May 24, 2012 | Next Release: May 31, 2012 Previous Issues Week: 01/19/2014 (View Archive) JUMP TO: In The News | Overview | Prices/Demand/Supply | Storage In the News: Natural Gas Rig Count Briefly Drops Below 600. The natural gas rotary rig count, as reported by Baker Hughes Incorporated, rose by 2 this week to 600, after falling to a 10-year low of 598 last week. After increasing modestly to 936 active rigs in the fall of 2011, the natural gas rig count has dropped sharply. The oil rig count, currently at 1,382, has generally risen steadily since 2009, largely in response to increasing crude oil prices. Natural gas rigs are currently down about 31 percent from their level at the same time last year, while oil rigs have risen by 45 percent over the

269

Water and Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

Water in swimming pool Water and Energy The water and energy technology research focuses on improving the efficiency of energy and water use in water delivery, supply and...

270

Energy Basics: Water Heating  

Office of Energy Efficiency and Renewable Energy (EERE) Indexed Site

about: Conventional Storage Water Heaters Demand (Tankless or Instantaneous) Water Heaters Heat Pump Water Heaters Solar Water Heaters Tankless Coil and Indirect Water Heaters...

271

Rigs Drilling Gas Wells Are At  

U.S. Energy Information Administration (EIA)

The increasing number of resulting gas well completions have been expanding production in major producing States, such as Texas. For the year 2000, ...

272

Reduction of iron-oxide-carbon composites: part II. Rates of reduction of composite pellets in a rotary hearth furnace simulator  

SciTech Connect

A new ironmaking concept is being proposed that involves the combination of a rotary hearth furnace (RHF) with an iron-bath smelter. The RHF makes use of iron-oxide-carbon composite pellets as the charge material and the final product is direct-reduced iron (DRI) in the solid or molten state. This part of the research includes the development of a reactor that simulated the heat transfer in an RHF. The external heat-transport and high heating rates were simulated by means of infrared (IR) emitting lamps. The reaction rates were measured by analyzing the off-gas and computing both the amount of CO and CO{sub 2} generated and the degree of reduction. The reduction times were found to be comparable to the residence times observed in industrial RHFs. Both artificial ferric oxide (PAH) and naturally occurring hematite and taconite ores were used as the sources of iron oxide. Coal char and devolatilized wood charcoal were the reductants. Wood charcoal appeared to be a faster reductant than coal char. However, in the PAH-containing pellets, the reverse was found to be true because of heat-transfer limitations. For the same type of reductant, hematite-containing pellets were observed to reduce faster than taconite-containing pellets because of the development of internal porosity due to cracking and fissure formation during the Fe2O{sub 3}-to-Fe3O{sub 4} transition. This is, however, absent during the reduction of taconite, which is primarily Fe3O{sub 4}. The PAH-wood-charcoal pellets were found to undergo a significant amount of swelling at low-temperature conditions, which impeded the external heat transport to the lower layers. If the average degree of reduction targeted in an RHF is reduced from 95 to approximately 70 pct by coupling the RHF with a bath smelter, the productivity of the RHF can be enhanced 1.5 to 2 times. The use of a two- or three-layer bed was found to be superior to that of a single layer, for higher productivities.

Halder, S.; Fruehan, R.J. [Praxair Inc., Tonawanda, NY (United States). Praxair Technological Center

2008-12-15T23:59:59.000Z

273

Water pollution  

SciTech Connect

Ballast water, which is sea water that is carried in oil tankers to provide stability, can become contaminated with oil. Alyeska Pipeline Service Company runs a water treatment plant at its pipeline terminal at Prot Valdez, Alaska, to treat ballast water before it is discharged into the sea. GAO reviewed EPA's recently reissued National Pollution Discharge Elimination System permit for the Port Valdez facility. In this report, GAO compares the effluent limits and other requirements under the reissued permit with those of the old permit, determines the reasons for changes in the reissued permit, and examines Alyeska's initial efforts to comply with the reissued permit's effluent limits and reporting requirements.

1990-06-01T23:59:59.000Z

274

Conveyor with rotary airlock apparatus  

DOE Patents (OSTI)

This invention is comprised of an apparatus for transferring objects from a first region to a second region, the first and second regions having differing atmospheric environments. The apparatus includes a shell having an entrance and an exit, a conveyer belt running through the shell from the entrance to the exit, and a horizontally mounted `revolving door` with at least four vanes revolving about its axis. The inner surface of the shell and the top surface of the conveyer belt act as opposing walls of the `revolving door`. The conveyer belt dips as it passes under but against the revolving vanes so as not to interfere with them but to engage at least two of the vanes and define thereby a moving chamber. Preferably, the conveyer belt has ridges or grooves on its surface that engage the edges of the vanes and act to rotate the vane assembly. Conduits are provided that communicate with the interior of the shell and allow the adjustment of the atmosphere of the moving chamber or recovery of constituents of the atmosphere of the first region from the moving chamber before they escape to the second region.

Kronbert, J.W.

1993-01-01T23:59:59.000Z

275

Rotary powder feed through apparatus  

DOE Patents (OSTI)

A device for increasing the uniformity of solids within a solids fabrication system, such as a direct light fabrication (DLF) system in which gas entrained powders are passed through the focal point of a moving high-power light which fuses the particles in the powder to a surface being built up in layers. The invention provides a feed through interface wherein gas entrained powders input from stationary input lines are coupled to a rotating head of the fabrication system. The invention eliminates the need to provide additional slack in the feed lines to accommodate head rotation, and therefore reduces feed line bending movements which induce non-uniform feeding of gas entrained powder to a rotating head.

Lewis, Gary K. (Los Alamos, NM); Less, Richard M. (Los Alamos, NM)

2001-01-01T23:59:59.000Z

276

The Development of an Energy Evaluation Tool for Chilled Water Systems  

E-Print Network (OSTI)

An energy evaluation tool for chilled water systems was developed. This tool quantifies the energy usage of various chilled water systems and typical energy conservation measures that are applied to these systems. It can be used as a screening tool to identify potential areas that can be further examined while only requiring a minimum number of inputs. The tool is useful for analyzing chiller plants with up to three electric chillers consisting of reciprocating, helical rotary, and/or centrifugal chillers. Both air-cooled and water-cooled systems can be analyzed with the tool, however, this article focuses on water-cooled systems. The tool is capable of analyzing the economics of the following energy conservation measures: 1) raising the chilled water temperature, 2) lowering the condenser temperature, 3) replacing the chiller(s), 4) using variable speed drives on centrifugal compressors, 5) utilizing free cooling, and 6) replacing electric chiller(s) with gas engine centrifugal chillers. For each of these measures, the tool calculates the annual energy and cost savings.

Stocki, M.; Kosanovic, D.; Ambs, L.

2001-05-01T23:59:59.000Z

277

WIND AND WATER POWER PROGRAM BUILDINGACLEAN  

E-Print Network (OSTI)

turbine research rig benefits from both single layered deposited thin film sensors and two- layered gauges used to test a single HP turbine stage. The facility was recently extended to 1.5 turbine stages in axial turbines. A set of phase-locked LDA measurements clearly show the extent of tip vortical flow near

278

Water Boatman  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Boatman Water Boatman Name: Joshua Location: N/A Country: N/A Date: N/A Question: I am doing a research on water boatman. I go through your web, I only find little information about it. Can you give me its habitat, its appearance, life cycles and communication between themselves and they defenses themselves? Replies: Find a good book in the library on insects, also on pond biology/ecology, as boatmen live in ponds and marshes. It should be easy to find. J.Elliott Try this web site: http://www.dnr.state.il.us/ctap.ctaphome.htm or http://www.dnr.state.il.us/nredu/nredpage.htm this is the state of Illinois Dept. of Natural Resources homepage and somewhere on there is a page called "bugpage". They have pictures and characteristics of aquatic insects there. good luck

279

Water Heaters and Hot Water Distribution Systems  

E-Print Network (OSTI)

gas water heaters; and pressure loss calculations for residentialgas water heaters; and pressure loss calculations for residential

Lutz, Jim

2012-01-01T23:59:59.000Z

280

Natural Gas - U.S. Energy Information Administration (EIA) - U.S. Energy  

Gasoline and Diesel Fuel Update (EIA)

30, 2012 | Release Date: May 31, 30, 2012 | Release Date: May 31, 2012 | Next Release: June 7, 2012 Previous Issues Week: 12/29/2013 (View Archive) JUMP TO: In The News | Overview | Prices/Demand/Supply | Storage In the News: Natural Gas Rigs Decline in Key Areas Active natural gas rotary rigs currently total 594, according to the latest weekly data released by Baker Hughes Incorporated. According to Baker Hughes data, natural gas-directed horizontal rigs have driven the decline in total natural gas rigs over the past several months. Horizontal-directed natural gas rig counts have fallen to 411, from levels in the low-600s a year ago. Declines have occurred in key areas of dry shale gas production, particularly in Louisiana, where the Haynesville Shale is located. The number of horizontal natural gas rigs drilling in Louisiana has fallen from

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 PREENGINEERED PRODUCTION LIFT DETERMINATION.......................................3-1 3.2 LIFTING FIXTURES..............................................................................................................3-2 3.2.1 Design ..........................................................................................................................3-2 3.2.2 Fabrication ...................................................................................................................3-2

282

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2007 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2007 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

283

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

2 2 CRITICAL LIFTS 2-i Chapter 2 Critical Lifts This chapter provides guidelines for critical-lift determination and requirements for planning and performing a critical lift safely and judiciously. 2.1 CRITICAL-LIFT DETERMINATION ................................................................ 2-1 2.2 CRITICAL-LIFT REQUIREMENTS ............................................................. 2-2 DOE-STD-1090-2004 Chapter 2 2-ii Critical Lifts INTENTIONALLY BLANK DOE-STD-1090-2004 2.1 CRITICAL-LIFT DETERMINATION 2-1 Chapter 2 Critical Lifts a. An appointed person shall classify each lift into one of the DOE categories (ordinary, critical, or preengineered production) prior to planning the lift. b. A lift shall be designated critical if any of

284

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

4 4 LIFTING PERSONNEL 4-i Chapter 4 Lifting Personnel This chapter describes requirements for lifting personnel. 4.1 GENERAL................................................................................................................................4-1 4.1.1 Personnel Lifting Evaluation .......................................................................................4-1 4.1.2 Designated Leader .......................................................................................................4-1 4.1.3 Trial Lift.......................................................................................................................4-2 4.1.4 Lifting Operations........................................................................................................4-2

285

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

CHAPTER 17 CHAPTER 17 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings. ASME B30.10, Hooks.

286

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS........................................1-1 DEFINITIONS........................................1-1 CHAPTER 2 CRITICAL LIFTS .......................................................................2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 PRENGINEERED PRODUCTION LIFT DETERMINATION................ 3-1 3.2 LIFTING FIXTURES .................................................................................... 3-2 3.3.1 Design ................................................................................................... 3-2 3.3.2 Fabrication ............................................................................................

287

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

9 9 MOBILE CRANES 9-i Chapter 9 Mobile Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of mobile cranes and implements the requirements of ASME B30.5 ("Mobile and Locomotive Cranes"). Only equipment built to appropriate design standards shall be used at DOE installations. 9.1 GENERAL .................................................................................................................................9-1 9.1.1 Operator Training/Qualification ..................................................................................9-1 9.1.2 Load Limits..................................................................................................................9-1 9.1.3 Load Rating Chart........................................................................................................9-1

288

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

8 8 HOISTS 8-i Chapter 8 Hoists This chapter provides safety standards for inspecting, testing, and operating hoists not permanently mounted on overhead cranes and implements the requirements of ASME B30.11 ("Monorail Systems and Underhung Cranes"), B30.16["Overhead Hoists (Underhung)"], and B30.21 ("Manually Lever Operated Hoists"). 8.1 GENERAL .................................................................................................................................8-1 8.1.1 Operator Training/Qualification ..................................................................................8-4 8.1.2 Marking........................................................................................................................8-4

289

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL ................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cab-Operated and Pulpit-Operated Cranes .............................................6-2

290

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i Chapter 10 Forklift Trucks This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ASME B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion-Engine-Powered Industrial Trucks") and 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

291

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

019-2004 019-2004 CHAPTER 16 MISCELLANEOUS LIFTING DEVICES 16-i Chapter 16 Miscellaneous Lifting Devices This chapter provides safety standards designated to sign verify, based on personal observations, certified records, or direct reports, that a specific action has been performed in accordance with specified requirements. For the operation, inspection, testing, and maintenance for miscellaneous lifting devices, (truck mounted cranes - capacity 1 ton or less not covered in ASME B30.5 ("Mobile and Locomotive Cranes") and implements the requirements of ASME PALD ("Portable Automotive Lifting Devices") for self contained shop cranes. 16.1 GENERAL ..................................................................................................................................

292

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 OVERHEAD AND GANTRY CRANES 7-i Chapter 7 Overhead and Gantry Cranes This chapter specifies operation, inspection, maintenance, and testing requirements for the use of overhead and gantry cranes and implements the requirements of ASME B30.2 ["Overhead and Gantry Cranes (Top- Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist)"], B30.11 ("Monorail Systems and Underhung Cranes"), and B30.17 ["Overhead and Gantry Cranes (Top-Running Bridge, Single Girder, Underhung Hoist")]. Only equipment built to the appropriate design standards shall be used in DOE installations. 7.1 GENERAL .................................................................................................................................7-1

293

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 6 PERSONNEL QUALIFICATION AND TRAINING 6-i Chapter 6 Personnel Qualification and Training This chapter describes personnel qualification and training. Only qualified personnel shall operate the equipment covered in this standard. 6.1 GENERAL................................................................................................................................6-1 6.2 QUALIFICATION...................................................................................................................6-2 6.2.1 General.........................................................................................................................6-2 6.2.2 Operators of Cap-Operated and Pulpit-Operated Cranes .............................................6-2

294

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

DEFINITIONS DEFINITIONS ................................................. 1-1 CHAPTER 2 CRITICAL LIFTS................................................................................. 2-1 2.1 CRITICAL-LIFT DETERMINATION........................................................ 2-1 2.2 CRITIAL-LIFT REQUIREMENTS............................................................. 2-2 CHAPTER 3 PREENGINEERED PRODUCTION LIFTS................................3-1 3.1 GENERAL....................................................................................................... 3-1 3.2 OPERATION EVALUATION ...................................................................... 3-2 3.2.1 Load Identification................................................................................

295

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0 0 FORKLIFT TRUCKS 10-i This chapter specifies operation, inspection, testing, and maintenance requirements for forklift trucks powered by internal-combustion engines or electric motors and implements the requirements of ANSI/ITSDF B56.1 ("Safety Standard for powered Industrial Trucks - Low Lift and High lift Trucks") and ANSI/ITSDF B56.6 ("Rough Terrain Fork Lift Trucks"), and ANSI/UL 558 ("Internal-Combustion- Engine-Powered Industrial Trucks") and ANSI/UL 583 ("Electric-Battery-Powered Industrial Trucks"). 10.1 GENERAL ...............................................................................................................................10-1 10.1.1 Operator Training/Qualification ................................................................................10-1

296

DOE-STD-1090-2004; Hoisting and Rigging (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

3 3 PREENGINEERED PRODUCTION LIFTS 3-i Chapter 3 Preengineered Production Lifts This chapter provides requirements for the design, evaluation, and performance of preengineered production lifts. This lift designation may be used at the discretion of the contractor for selected operations. 3.1 GENERAL................................................................................................................................3-1 3.2 OPERATION EVALUATION................................................................................................3-2 3.2.1 Load Identification.......................................................................................................3-2 3.2.2 Task Determination......................................................................................................3-2

297

DOE-STD-1090-2007; Hoisting and Rigging Standard (Formerly Hoisting and Rigging Manual)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

7 7 REFERENCES 17-1 Chapter 17 References American Institute of Steel Construction AISC Specifications for the design, fabrication, and erection of structural steel for buildings. American Iron and Steel Institute AISI Standards for Type-302 or Type-304 stainless steel. American National Standards Institute and the American Society of Mechanical Engineers ANSI A10.28, Work Platforms Suspended From Cranes or Derricks. ANSI A10.18, Floor and Wall Openings, Railings and Toe Boards. ASME B30.1, Jacks ASME B30.2, Overhead and Gantry Cranes (Top-Running Bridge, Single or Multiple Girder, Top-Running Trolley Hoist). ASME B30.5, Mobile and Locomotive Cranes. ASME B30.6, Derricks. ASME B30.7, Base-Mounted Drum Hoists. ASME B30.9, Slings.

298

U.S. oil rig count overtakes natural gas rig count - Today in ...  

U.S. Energy Information Administration (EIA)

Petroleum & Other Liquids. Crude oil, gasoline, heating oil, diesel, propane, and other liquids including biofuels and natural gas liquids. Natural Gas

299

Water Heaters and Hot Water Distribution Systems  

E-Print Network (OSTI)

The effect on water and gas usage from cross-flow betweencontrols have on water and gas usage over a large number ofsystems, and their water and gas usage. Hourly schedules for

Lutz, Jim

2012-01-01T23:59:59.000Z

300

Efficient Water Use & Management  

NLE Websites -- All DOE Office Websites (Extended Search)

Sustainability Goals Water Use Goal 4: Efficient Water Use & Management Aware of the arid climate of northern New Mexico, water reduction and conservation remains a primary...

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Water and Energy Interactions  

E-Print Network (OSTI)

A white paper describing produced water from production ofCE, Veil JA. 2009. Produced Water Volumes and Managementunderground formations (produced water) are often extracted

McMahon, James E.

2013-01-01T23:59:59.000Z

302

Saving Water Saves Energy  

E-Print Network (OSTI)

of California’s Water Conservation Standards for ResidentialCalifornia Urban Water Conservation Council, 2006. http://http://www.nrdc.org/water/conservation/edrain/edrain.pdf

McMahon, James E.; Whitehead, Camilla Dunham; Biermayer, Peter

2006-01-01T23:59:59.000Z

303

Texas Hot Water Report  

NLE Websites -- All DOE Office Websites (Extended Search)

coil hot water storage tank, a backup instantaneous electric water heater, a hydronic fan coil unit for space heating, and an efficient plumbing manifold for domestic hot water...

304

Water Permits (Louisiana)  

Energy.gov (U.S. Department of Energy (DOE))

The Water Permits Division authorizes permits administered under the Water Quality Regulations. Louisiana's Water Quality Regulations require permits for the discharge of pollutants from any point...

305

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil and Natural Gas Crude Oil and Natural Gas Resource Development Figure 5.1 Crude Oil and Natural Gas Resource Development Indicators Rotary Rigs in Operation by Type, 1949-2012 Rotary Rigs in Operation by Type, Monthly Active Well Service Rig Count, Monthly Total Wells Drilled by Type, 1949-2010 . 76 U.S. Energy Information Administration / Monthly Energy Review November 2013 Total 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 1 2 3 4 Thousand Rigs 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 10 20 30 40 50 Thousand Wells Dry Wells Crude Oil Wells Web Page: http://www.eia.gov/totalenergy/data/monthly/#crude. Sources: Tables 5.1 and 5.2.

306

Word Pro - S5  

U.S. Energy Information Administration (EIA) Indexed Site

Crude Oil and Natural Gas Resource Development Indicators Rotary Rigs in Operation by Type, 1949-2012 Rotary Rigs in Operation by Type, Monthly Active Well Service Rig Count, Monthly Total Wells Drilled by Type, 1949-2010 . 76 U.S. Energy Information Administration / Monthly Energy Review November 2013 Total 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 1 2 3 4 Thousand Rigs 1950 1955 1960 1965 1970 1975 1980 1985 1990 1995 2000 2005 2010 0 10 20 30 40 50 Thousand Wells Dry Wells Crude Oil Wells Web Page: http://www.eia.gov/totalenergy/data/monthly/#crude. Sources: Tables 5.1 and 5.2. Crude Oil J FMAMJ J A SOND J FMAMJ J A SOND J FMAMJ J

307

Water Beetles  

NLE Websites -- All DOE Office Websites (Extended Search)

Beetles Beetles Nature Bulletin No. 639-A April 29, 1961 Forest Preserve District of Cook County George W. Dunne, President Roland F. Eisenbeis Supt. of Conservation WATER BEETLES The world is full of beetles. They live everywhere except in the oceans and in the polar regions. There are more of them than any other kind of insect. A quarter of a million species are known and new ones are being discovered every year. Whether it is a microscopic mushroom beetle a hundredth of an inch long, or a giant six-inch Hercules beetle from South America, it can be recognized by its wings. The upper pair forms a hard shell curving like a shield over the thin folded lower wings and the abdomen. In flight, the upper pair is extended like the wings of an airplane and the lower two become buzzing propellers.

308

Water watch  

Science Conference Proceedings (OSTI)

The Hydropower Generation Report provides generation figures for the largest hydropower producers in each of six regions in the US. The report compares, for each month, the amount of hydroelectricity generated (in thousands of megawatt-hours) by each producers in the last two years to the ten-year average for that month. This database is used to figure long-term generation averages and percent of averages. The producers regularly provide current generation data to update the database. This issue of [open quotes]Water Watch[close quotes] focuses on winter snow conditions across the US as of mid-January. In addition, the department provides an outlook of spring flood potential. The information presented is based on data from the US Geological Survey, the National Weather Service, and the Soil Conservation Service.

Not Available

1991-02-01T23:59:59.000Z

309

Water Conservation Tips  

E-Print Network (OSTI)

Gardener Water Conservation Tips fo r t h e UCSC Farm &share some of the water-conservation techniques used at theWinter Squash Water Conservation Mulches will save water,

Brown, Martha

2008-01-01T23:59:59.000Z

310

Drinking Water Problems: Lead  

E-Print Network (OSTI)

Lead in drinking water can damage the brain, kidneys, nervous system and red blood cells. This publication explains how lead can enter drinking water, how to have your water tested, and how to eliminate lead from drinking water.

Dozier, Monty; McFarland, Mark L.

2004-02-20T23:59:59.000Z

311

Water Conservation Tips  

E-Print Network (OSTI)

Gardener Water Conservation Tips fo r t h e UCSC Farm &we share some of the water-conservation techniques used atWinter Squash Water Conservation Mulches will save water,

Brown, Martha

2008-01-01T23:59:59.000Z

312

NIST: NIF - Water Sensitivity  

Science Conference Proceedings (OSTI)

Water Sensitivity. Neutrons are extremely sensitive to small amounts of water. To quantify and calibrate this sensitivity we ...

313

Conventional Storage Water Heaters  

Energy.gov (U.S. Department of Energy (DOE))

Conventional storage water heaters remain the most popular type of water heating system for homes and buildings.

314

ARM: Microwave Radiometer data (MWR Profiles - QME), water vapor, temp, cloud liquid water, precip water retrievals  

DOE Data Explorer (OSTI)

Microwave Radiometer data (MWR Profiles - QME), water vapor, temp, cloud liquid water, precip water retrievals

Maria Cadeddu

315

WATER AND GROWTH: FUTURE WATER SUPPLIES FOR  

E-Print Network (OSTI)

. Reclaimed Water As people use water, a wastewater stream is produced. Once cleaned to acceptable standards and is available as reclaimed water. #12;20 New growth in central Arizona will produce significant quantities to return for wastewater treatment51 . Of the reclaimed water produced, 30% is assumed available to meet

Gelt, Joe

316

Partnering to Save Water  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Partnering Partnering to Save Water Phill Consiglio Southern California Edison What We Are Going to Discuss * A Little Bit About Water * The Energy Cost of Water * Water Technologies * What We Have Done * Where We Are Going A Little Bit About Water *The Earth Has A Finite Supply Of Fresh Water. - Water Is Stored In Aquifers, Surface Waters And The Atmosphere - Sometimes Oceans Are Mistaken For Available Water, But The Amount Of Energy Needed To Convert Saline Water To Potable Water Is Prohibitive Today *This Has Created A Water Crisis Due To: - Inadequate Access To Safe Drinking Water For About 884 Million People - Inadequate Access To Water For Sanitation And Waste Disposal For 2.5 Billion People - Groundwater Overdrafting (Excessive Use) Leading To Diminished Agricultural Yields

317

Office of Legacy Management Categorical Exclusion Determination Form  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Install two groundwater monitoring wells at the Bluewater Uranium Mill Tailings Radiation Install two groundwater monitoring wells at the Bluewater Uranium Mill Tailings Radiation Control Act site near Grants, New Mexico. LM # 10-12 Location : Near Grants, New Mexico Proposed Action or Project Description: DO E proposes to install two groundwater monitoring wells- 20(M) and 11 (SG)- on the Bluewater disposal site using a truck-mounted rotary drill rig. The boreholes would extend to depths of 140 to 280 feet below ground surface and would be completed with a polyvinyl chloride casing that has an outside diameter of 4.5 inches . Water and bentonite would be used for the drilling fluid ; if the drilling company requires additives , DOE would require the use of green products . Drill cuttings , which would consist of ground-up native rock with bentonite

318

Water Heaters and Hot Water Distribution Systems  

E-Print Network (OSTI)

Water Distribution System Recommendations for the 2008 Title- 24 Residential Building Energy Efficiency Standards .. 4 Multi-FamilyWater Distribution System Recommendations for the 2008 Title- 24 Residential Building Energy Efficiency Standards 11 Multi-FamilyWater Distribution System Recommendations for the 2008 Title- 24 Residential Building Energy Efficiency Standards 48 Multi-Family

Lutz, Jim

2012-01-01T23:59:59.000Z

319

Water heater heat reclaimer  

SciTech Connect

This invention relates to the conservation of energy in a domestic gas water heater by utilizing the hot exhaust gases in a gas water heater for the preheating of the incoming unheated water into the water heater. The exhaust gases from a domestic gas water heater carry wasted heat and the present invention provides a mean to reclaim part of the wasted heat for the preheating of the incoming unheated water during hot water usage periods. During non hot water usage periods the heat in the exhaust gases is not reclaimed to prevent overheating of the water and also to prevent the formation of water deposit in the preheating assembly or heat reclaimer. During the non hot water usage periods the heat produced in the water heater is normally needed only to maintain the desired water temperature of the stored water in the water tank of the water heater. Due to the rapid heating or recovery rate, the present invention enables the use of a smaller water heater. The use of a smaller water heater reduces the normal heat loss from the stored hot water thereby further reduces energy consumption.

Wie, C.T.

1983-08-09T23:59:59.000Z

320

Feature - WATER Tool Released  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Assessment for Transportation Energy Resources (WATER) Tool Released Water Assessment for Transportation Energy Resources (WATER) Tool Released Argonne National Laboratory recently released an open access online tool called WATER (Water Assessment for Transportation Energy Resources), which quantifies water footprint of fuel production stages from feedstock production to conversion process for biofuel with county, state, and regional level spatial resolution. WATER provides analysis on water consumption and its impact on water quality. It contains biofuel pathways for corn grain ethanol, soybean biodiesel, and cellulosic ethanol produced from corn stover and wheat straw. Perennial grass (Switchgrass and Miscanthus) and forest wood residue-based biofuel pathways are currently under development. The WATER tool enables users to conduct pathway comparison, scenario development, and regional specific feedstock analysis in supporting of biofuel industry development and planning. It is available at http://water.es.anl.gov/.

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Tankless Demand Water Heaters  

Energy.gov (U.S. Department of Energy (DOE))

Demand (tankless or instantaneous) water heaters have heating devices that are activated by the flow of water, so they provide hot water only as needed and without the use of a storage tank. They...

322

Review: Globalization of Water  

E-Print Network (OSTI)

Review: Globalization of Water: Sharing the Planet’sAshok K. Globalization of Water: Sharing the Planet’s140) liters of virtual water (p. 15). This is one of the

Tennant, Matthew Aaron

2009-01-01T23:59:59.000Z

323

Saving Water Saves Energy  

E-Print Network (OSTI)

H. , Groves D. California Water 2030: An Efficient Future,Preemption of California’s Water Conservation Standards for2Epdf Biermayer P. Potential Water and Energy Savings from

McMahon, James E.; Whitehead, Camilla Dunham; Biermayer, Peter

2006-01-01T23:59:59.000Z

324

Water, Water Everywhere: How Can We Understand It?  

Science Conference Proceedings (OSTI)

... Science Afternoon. Water, Water Everywhere: How Can We Understand It? An exploration of water using physical models and computer simulation. ...

2012-10-01T23:59:59.000Z

325

Water Rx - The Problem of Pharmaceuticals in Our Nation's Waters  

E-Print Network (OSTI)

IN OUR NATION'S WATERS intake via drinking water wastherapeutic dose and intake via drinking water was 150,000

Leitman, Melanie

2011-01-01T23:59:59.000Z

326

Drinking Water Standards  

E-Print Network (OSTI)

This publication explains the federal safety standards for drinking water provided by public water supply systems. It discusses the legal requirements for public water supplies, the maximum level allowed for contaminants in the water, and the potential health effects of each contaminant regulated. People who use water from private sources such as wells can also use these standards as a guide in checking whether their water is safe.

Dozier, Monty; McFarland, Mark L.

2006-04-26T23:59:59.000Z

327

Carbon and Water Resource Management for Water Distribution Systems  

E-Print Network (OSTI)

4 April, 2013. (4) 2010 Water Use Survey Summary Estimates –State Totals; Texas Water Development Board: Austin, TX,indicators for urban water systems. Urban Water. 2004, 4,

Hendrickson, Thomas Peter

2013-01-01T23:59:59.000Z

328

Ultraviolet Water Treatment  

Science Conference Proceedings (OSTI)

UV Ray of Hope for Safer Drinking Water. ... It is not, however, too soon for the American Water Works Association to express its appreciation. ...

2013-01-03T23:59:59.000Z

329

NETL: Water - Energy Interface  

NLE Websites -- All DOE Office Websites (Extended Search)

Home > Technologies > Coal & Power Systems > Innovations for Existing Plants > Water - Energy Interface Innovations for Existing Plants Water - Energy Interface Previous Next...

330

Membranes for Clean Water  

Science Conference Proceedings (OSTI)

Membranes for Clean Water. Summary: ... Description: Impact. Access to affordable, clean water is vital to the nation's economic growth and security. ...

2013-02-02T23:59:59.000Z

331

Drinking Water Problems: Copper  

E-Print Network (OSTI)

High levels of copper in drinking water can cause health problems. This publication explains the effects of copper in water and methods of removing it. 4 pp.

Dozier, Monty; McFarland, Mark L.; Lesikar, Bruce J.

2006-01-25T23:59:59.000Z

332

Water and Energy Interactions  

E-Print Network (OSTI)

water and wasted embodied energy. While 5% of California'senergy intensive (94). Water- inefficient fixtures and fittings (toilets, showerheads, urinals, faucets) represent both wasted

McMahon, James E.

2013-01-01T23:59:59.000Z

333

Review: Globalization of Water  

E-Print Network (OSTI)

using virtual water (e.g. coffee produced in an environmentis produced in an environment in which it takes less water

Tennant, Matthew Aaron

2009-01-01T23:59:59.000Z

334

Water-heating dehumidifier  

DOE Patents (OSTI)

A water-heating dehumidifier includes a refrigerant loop including a compressor, at least one condenser, an expansion device and an evaporator including an evaporator fan. The condenser includes a water inlet and a water outlet for flowing water therethrough or proximate thereto, or is affixed to the tank or immersed into the tank to effect water heating without flowing water. The immersed condenser design includes a self-insulated capillary tube expansion device for simplicity and high efficiency. In a water heating mode air is drawn by the evaporator fan across the evaporator to produce cooled and dehumidified air and heat taken from the air is absorbed by the refrigerant at the evaporator and is pumped to the condenser, where water is heated. When the tank of water heater is full of hot water or a humidistat set point is reached, the water-heating dehumidifier can switch to run as a dehumidifier.

Tomlinson, John J. (Knoxville, TN)

2006-04-18T23:59:59.000Z

335

Research Addressing Power Plant Water  

NLE Websites -- All DOE Office Websites (Extended Search)

Addressing Power Plant Water Management to Minimize Water Use while Providing Reliable Electricity Generation Water and Energy 2 Water and Energy are inextricably linked. Because...

336

Movement and Injury Rates for Three Life Stages of Spring Chinook Salmon Oncorhynchus Tshawytscha : A Comparison of Submerged Orifices and an Overflow Weir for Fish Bypass in a Modular Rotary Drum Fish Screen : Annual Report 1995.  

DOE Green Energy (OSTI)

The Pacific Northwest National Laboratory (PNNL) evaluated the effectiveness of 6-in. and 2-in. submerged orifices, and an overflow weir for fish bypass at a rotary drum fish screening facility. A modular drum screen built by the Washington Department of Fish and Wildlife (WDFW) was installed at PNNL`s Aquatic Ecology research laboratory in Richland, Washington. Fry, subyearlings, and smolts of spring chinook salmon (Oncorhynchus tshawyacha) were introduced into the test system, and their movement and injury rates were monitored. A total of 33 tests (100 fish per test) that lasted from 24 to 48 hr were completed from 1994 through 1995. Passage rate depended on both fish size and bypass configuration. For fry/fingerling spring chinook salmon, there was no difference in passage rate through the three bypass configurations (2-in. orifice, 6-in. orifice, or overflow weir). Subyearlings moved sooner when the 6-in. orifice was used, with more than 50% exiting through the fish bypass in the first 8 hr. Smolts exited quickly and preferred the 6-in. orifice, with over 90% of the smolts exiting through the bypass in less than 2 hr. Passage was slightly slower when a weir was used, with 90% of the smolts exiting in about 4 hr. When the 2-in. orifice was used in the bypass, 90% of the smolts did not exit until after 8 hr. In addition, about 7% of the smolts failed to migrate from the forebay within 24 hr, indicating that smolts were significantly delayed when the 2-in. orifice was used. Few significant injuries were detected for any of the life stages. However, light descaling occurred on about 15% of chinook salmon smolts passing through the 2-in. orifice. Although a single passage through the orifice did not appear to cause significant scale loss or other damage, passing through several screening facilities with 2-in. orifices could cause cumulative injuries.

Abernethy, C. Scott; Neitzel, Duane A.; Mavros, William V.

1996-03-01T23:59:59.000Z

337

Lawn Water Management  

E-Print Network (OSTI)

Water is a limited resource in Texas. This booklet explains how homeowners can establish a water management program for a home lawn that both maintains a healthy sod and also conserves water. The publication discusses soil types, grass varieties, management practices and watering techniques.

McAfee, James

2006-06-26T23:59:59.000Z

338

WaterSense Program: Methodology for National Water Savings Analysis Model Indoor Residential Water Use  

E-Print Network (OSTI)

Fixtures Market Overview: Water Savings Potential forNew Jersey. American Water Works Association ResearchResidential End Uses of Water (REUWS). 1999. American Water

McNeil, Michael

2008-01-01T23:59:59.000Z

339

Service Water Piping Guideline  

Science Conference Proceedings (OSTI)

In the years 1988 and 1989, EPRI organized the Service Water Working Group (SWWG) to identify and help resolve the many issues surrounding service water (SW) systems in nuclear power plants. One issue identified by the SWWG was corrosion in service water piping systems. Interest in this issue resulted in the development of several technical reports: Guidelines for the Repair/Replacement Welding of Nuclear Service Water Systems, TR-100386; Guide for the Examination of Service Water System Piping, TR-10206...

2005-09-30T23:59:59.000Z

340

Energy Water Linkage: Projected Water Needs  

NLE Websites -- All DOE Office Websites (Extended Search)

June 2004 Executive Summary Thermoelectric generation requires large volumes of water, primarily for cooling. An analysis was conducted to estimate the demand...

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Engineering Task Plan for Water Supply for RMCS Spray Wash Trailer  

Science Conference Proceedings (OSTI)

This ETP defines the task and deliverables associated with the design, fabrication and testing of an improved spray wash system for the Rotary Mode Core Sampling (RMCS)Spray Wash Trailer.

BOGER, R.M.

2000-04-20T23:59:59.000Z

342

Engineering Task Plan for Water Supply for Spray Washers on the Support Trucks  

SciTech Connect

This Engineering Task Plan (ETP) defines the task and deliverables associated with the design, fabrication and testing of an improved spray wash system for the Rotary Mode Core Sampling (RMCS) System Support Trucks.

BOGER, R.M.

2000-02-03T23:59:59.000Z

343

Becker, K., Malone, M.J., et al., 1998 Proceedings of the Ocean Drilling Program, Initial Reports, Vol. 174B  

E-Print Network (OSTI)

(drill-pipe measurement from rig floor, mbrf): 4457.1 Total depth (drill-pipe measurement from rig floor, mbrf): 4526.6 Distance between rig floor and sea level (m): 11.6 Water depth (drill-pipe measurement Unit II (63.5-69.5 mbsf): Aphyric basalt Principal results: Sixty-four meters of sediment and 0.58 m

344

Reactor water cleanup system  

DOE Patents (OSTI)

A reactor water cleanup system includes a reactor pressure vessel containing a reactor core submerged in reactor water. First and second parallel cleanup trains are provided for extracting portions of the reactor water from the pressure vessel, cleaning the extracted water, and returning the cleaned water to the pressure vessel. Each of the cleanup trains includes a heat exchanger for cooling the reactor water, and a cleaner for cleaning the cooled reactor water. A return line is disposed between the cleaner and the pressure vessel for channeling the cleaned water thereto in a first mode of operation. A portion of the cooled water is bypassed around the cleaner during a second mode of operation and returned through the pressure vessel for shutdown cooling.

Gluntz, Douglas M. (San Jose, CA); Taft, William E. (Los Gatos, CA)

1994-01-01T23:59:59.000Z

345

Instantaneous gas water heater  

SciTech Connect

Hot water supply temperature is set by a temperature setting device in response to an instantaneous flow rate signal from a water flow rate sensor arranged in a water supply pipe and a feeding water temperature signal from a feeding water temperature sensor which are compared with a predetermined hot water supply temperature and calculated in a control unit. A proportional valve and other devices in a gas supply pipe are controlled in response to the result of the comparison and calculation to define a required volume of gas for ignition and heating. At the same time, a fan damper is controlled by a damper control device so as to adjust the volume of combustion air. A signal representing discharging hot water temperature from a discharging hot water temperature sensor arranged in a hot water feeding pipe is fed back to the control unit and calculated therein, and a valve in the hot water supply pipe is adjusted in response to the result of calculation to attain the desired hot water supply temperature. In order to prevent freezing in the system in winter season, a signal from a thermostat in the water feeding pipe is transmitted to a heater arranged in an air supply chamber so as to heat a heat exchanger pipe and, at the same time, heaters arranged in the water feeding pipe and the hot water supply pipe are also controlled to prevent freezing.

Tsutsui, O.; Kuwahara, H.; Murakami, Sh.; Yasunaga, Sh.

1985-02-26T23:59:59.000Z

346

Arnold Schwarzenegger WATER HEATERS AND HOT WATER  

E-Print Network (OSTI)

controls. This response applies to markets that have a demand for central water heating systems Distribution Systems Subtask 2.1 Multifamily Water Heating Construction Practices, Pricing and Availability systems in multifamily buildings. This market characterization study is helping HMG develop

347

ii Produced Water Pretreatment for Water Recovery  

E-Print Network (OSTI)

Horizontal drilling and slickwater hydrofracturing have enabled shale gas to become a significant contributor to the United States ’ energy supply. Hydrofracturing typically requires 2MM – 6.5MM gallons of water per shale gas well. About 15-25 % of this water returns to the surface as “flowback ” within 30 days after hydrofracturing. “Produced water ” continues to flow at a much reduced rate, e.g. 2-10 bbl/day, for the life of the well. In addition to high salinity and hardness levels (Mg, Ca, Sr, Ba), much Marcellus produced water also contains significant levels of naturally occurring radioactive materials (NORM), particularly radium. The near absence of disposal wells in Pennsylvania initially forced much of the produced water to be trucked into Ohio for disposal by deep-well injection (UIC). Currently up to 95 % of the

Principal Investigator; James M. Silva; James M. Silva; Hope Matis; William L. Kostedt Iv; Vicki Watkins

2012-01-01T23:59:59.000Z

348

Energy-Water Overview  

U.S. Energy Information Administration (EIA) Indexed Site

Emerging Issues and Challenges Emerging Issues and Challenges DOE/EIA 2010 Energy Conference Mike Hightower Sandia National Laboratories mmhight@sandia.gov, 505-844-5499 Energy and Water are ... Interdependent Water for Energy and Energy for Water Energy and power production require water: * Thermoelectric cooling * Hydropower * Energy minerals extraction/mining * Fuel Production (fossil fuels, H 2 , biofuels) * Emission control Water production, processing, distribution, and end-use require energy: * Pumping * Conveyance and Transport * Treatment * Use conditioning * Surface and Ground water Water Consumption by Sector U.S. Freshwater Consumption, 100 Bgal/day Livestock 3.3% Thermoelectric 3.3% Commercial 1.2% Domestic 7.1% Industrial 3.3% Mining 1.2% Irrigation 80.6% Energy uses 27 percent of all non-agricultural fresh water

349

Water Management Planning  

NLE Websites -- All DOE Office Websites (Extended Search)

water efficiency water efficiency at Federal sites Background The Federal Energy Management Program (FEMP) sponsored a water assessment at the Y-12 National Security Complex (Y-12) located in Oak Ridge, Tennessee, during fiscal year 2010. Driven by mandated water reduction goals of Executive Orders 13423 and 13514, the objective of the water assessment was to develop a comprehensive understanding of the current water-consuming applications and equipment at Y-12 and to identify key areas for water efficiency improvements. The water-assessment team learned key lessons from the Y-12 assessment. Therefore, the aim of this document is to share these key lessons to help other large process-driven sites at the Department of Energy (DOE) and beyond develop a comprehensive

350

Water Management Planning  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

water efficiency water efficiency at Federal sites Background The Federal Energy Management Program (FEMP) sponsored a water assessment at the Y-12 National Security Complex (Y-12) located in Oak Ridge, Tennessee, during fiscal year 2010. Driven by mandated water reduction goals of Executive Orders 13423 and 13514, the objective of the water assessment was to develop a comprehensive understanding of the current water-consuming applications and equipment at Y-12 and to identify key areas for water efficiency improvements. The water-assessment team learned key lessons from the Y-12 assessment. Therefore, the aim of this document is to share these key lessons to help other large process-driven sites at the Department of Energy (DOE) and beyond develop a comprehensive

351

Water | OpenEI  

Open Energy Info (EERE)

Water Water Dataset Summary Description This dataset is from the report Operational water consumption and withdrawal factors for electricity generating technologies: a review of existing literature (J. Macknick, R. Newmark, G. Heath and K.C. Hallett) and provides estimates of operational water withdrawal and water consumption factors for electricity generating technologies in the United States. Estimates of water factors were collected from published primary literature and were not modified except for unit conversions. Source National Renewable Energy Laboratory Date Released August 28th, 2012 (2 years ago) Date Updated Unknown Keywords coal consumption csp factors geothermal PV renewable energy technologies Water wind withdrawal Data application/vnd.openxmlformats-officedocument.spreadsheetml.sheet icon Operational water consumption and withdrawal factors for electricity generating technologies (xlsx, 77.7 KiB)

352

Report on Produced Water  

NLE Websites -- All DOE Office Websites (Extended Search)

water is the largest volume by-product or waste stream associated with oil and gas exploration and production. The cost of managing such a large volume of water is a key...

353

Boiling Water in Microwave  

NLE Websites -- All DOE Office Websites (Extended Search)

Boiling Water in Microwave A 26-year old man decided to have a cup of coffee. He took a cup of water and put it in the microwave to heat it up (something that he had done numerous...

354

A gathering of water  

E-Print Network (OSTI)

The act of immersion is a powerful catalyst for the affirmation or transformation of identity. How we place ourselves in water expresses cultural valuations of our bodies, water, and social relations, as well as categories ...

Horowitz, Naomi Leah, 1970-

2005-01-01T23:59:59.000Z

355

Walking on water  

E-Print Network (OSTI)

The ingenious methods employed by insects and spiders to move across a water surface rely on microphysics that is of little use to larger water walkers but of considerable interest to the microfluidics community.

Bush, John W. M.

356

Madrid Hot Water Report  

NLE Websites -- All DOE Office Websites (Extended Search)

Comprehensive Assessment of Hot Water System Page 1 of 2 HOT WATER SYSTEM In general, the plumbing system in MAGIC BOX is designed to concentrate all devices, be they storage,...

357

Water Conservation Tips  

E-Print Network (OSTI)

Water Needs breath. Adding compost to sandy soils helps thesoil retain water longer—the compost acts like a sponge,from applications of compost and other organic matter. For

Brown, Martha

2008-01-01T23:59:59.000Z

358

Drinking Water Problems: Arsenic  

E-Print Network (OSTI)

High levels of arsenic in drinking water can poison and even kill people. This publication explains the symptoms of arsenic poisoning and common treatment methods for removing arsenic from your water supply.

Lesikar, Bruce J.; Melton, Rebecca; Hare, Michael; Hopkins, Janie; Dozier, Monty

2005-12-02T23:59:59.000Z

359

Water Prism Volume 1  

Science Conference Proceedings (OSTI)

This report documents the design and implementation of Water Prism, a decision support system that evaluates alternative management plans to obtain water resource sustainability at the regional, watershed or local levels. It considers surface, ground and impoundment waters, and all water using sectors (industrial, agricultural, municipal, electric power and the environment). This report will be of value to environment, generation, and planning managers within power companies, government agencies, ...

2012-12-06T23:59:59.000Z

360

Demystifying water treatment  

SciTech Connect

Increasingly accountable for the environmental quality and cost of managing their waste and process water streams, customers require more precise data about the constituents in their water. This has forced suppliers to unlock some of the secrets of water treatment. In the open exchange of information, users are trading in esoteric formulations for products that are more chemical efficient and environmentally benign. Factoring more prominently in the water treatment equation are service and supply. This paper reviews some of these simpler treatments.

Hairston, D.

1994-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Water and Energy Interactions  

E-Print Network (OSTI)

History 4 Water Used For Fuel Production.. 4 Coal Production .. 6 Carbon Capture and Sequestration .. 7 Natural Gas

McMahon, James E.

2013-01-01T23:59:59.000Z

362

Water and Energy Interactions  

E-Print Network (OSTI)

Hydroelectricity for agriculture and hydroelectricity. Large volumes of waterElectricity Production Hydroelectricity The most common type

McMahon, James E.

2013-01-01T23:59:59.000Z

363

What's In My Water?  

E-Print Network (OSTI)

You can learn about the quality of your water by sending a sample to a laboratory for analysis. This publication will help you understand the lab report by explaining the properties, components and contaminants often found in water. It describes the sources of water contaminants, problems that can be caused by those contaminants, suggestions for correcting problems, and the safe levels of each contaminant in water for household use, for irrigation and for livestock.

Provin, Tony; Pitt, John L.

2003-04-21T23:59:59.000Z

364

Saving Water Saves Energy  

SciTech Connect

Hot water use in households, for showers and baths as wellas for washing clothes and dishes, is a major driver of household energyconsumption. Other household uses of water (such as irrigatinglandscaping) require additional energy in other sectors to transport andtreat the water before use, and to treat wastewater. In California, 19percent of total electricity for all sectors combined and 32 percent ofnatural gas consumption is related to water. There is a criticalinterdependence between energy and water systems: thermal power plantsrequire cooling water, and water pumping and treatment require energy.Energy efficiency can be increased by a number of means, includingmore-efficient appliances (e.g., clothes washers or dishwashers that useless total water and less heated water), water-conserving plumbingfixtures and fittings (e.g., showerheads, faucets, toilets) and changesin consumer behavior (e.g., lower temperature set points for storagewater heaters, shorter showers). Water- and energy-conserving activitiescan help offset the stress imposed on limited water (and energy) suppliesfrom increasing population in some areas, particularly in drought years,or increased consumption (e.g., some new shower systems) as a result ofincreased wealth. This paper explores the connections between householdwater use and energy, and suggests options for increased efficiencies inboth individual technologies and systems. Studies indicate that urbanwater use can be reduced cost-effectively by up to 30 percent withcommercially available products. The energy savings associated with watersavings may represent a large additional and largely untappedcost-effective opportunity.

McMahon, James E.; Whitehead, Camilla Dunham; Biermayer, Peter

2006-06-15T23:59:59.000Z

365

Energy-Water Nexus  

SciTech Connect

Conclusions of this presentation are: (1) energy and water are interconnected; (2) new energy sources will place increased demands on water supplies; (3) existing energy sources will be subjected to increasing restrictions on their water use; and (4) integrated decision support tools will need to be developed to help policy makers decide which policies and advanced technologies can address these issues.

Horak, W.

2010-07-26T23:59:59.000Z

366

Corrosion in Water  

Science Conference Proceedings (OSTI)

Table 1   Corrosion of chemical lead in industrial and domestic waters...ppm hardness 22 72 Yes Slow 6.35 0.25 Cooling tower water, oxygenated, from Lake Erie 16â??29 60â??85 Complete None 134.6 5.3 Los Angeles aqueduct water, treated with chlorine

367

Water treatment method  

DOE Patents (OSTI)

A method for reducing the concentration of any undesirable metals dissolved in contaminated water, such as waste water. The method involves uniformly reacting the contaminated water with an excess amount of solid particulate calcium sulfite to insolubilize the undesirable metal ions, followed by removal thereof and of the unreacted calcium sulfite.

Martin, Frank S. (Farmersville, OH); Silver, Gary L. (Centerville, OH)

1991-04-30T23:59:59.000Z

368

Water treatment on wheels  

Science Conference Proceedings (OSTI)

Design options and combinations of fixed and mobile demineralization equipment give power plant operators the flexibility to continually optimize their water treatment system to meet rapidly changing needs. The article classifies water treatment service contracts for demineralized water into four categories and presents associated design, economic and operational advantages to power plant designers, constructors, owners and operators. 1 tab.

Taylor, R.T.

2005-09-01T23:59:59.000Z

369

Water treatment method  

DOE Patents (OSTI)

A method for reducing the concentration of many undesirable metals dissolved in contaminated water, such as waste water. The method involves uniformly reacting the contaminated water with an excess amount of solid particulate calcium sulfite to insolubilize the undesirable metal ions, followed by removal thereof and of the unreacted calcium sulfite. 1 tab.

Martin, F.S.; Silver, G.L.

1990-02-02T23:59:59.000Z

370

Drinking Water Problems: Radionuclides  

E-Print Network (OSTI)

Radionuclides in drinking water can cause serious health problems for people. This publication explains what the sources of radionuclides in water are, where high levels have been found in Texas, how they affect health and how to treat water to remove them.

Lesikar, Bruce J.; Melton, Rebecca; Hare, Michael; Hopkins, Janie; Dozier, Monty

2006-08-04T23:59:59.000Z

371

Reduction of Water Consumption  

E-Print Network (OSTI)

Cooling systems using water evaporation to dissipate waste heat, will require one pound of water per 1,000 Btu. To reduce water consumption, a combination of "DRY" and "WET" cooling elements is the only practical answer. This paper reviews the various options available: WET-DRY towers, or DRY-WET, or combination WET and DRY towers!

Adler, J.

1985-05-01T23:59:59.000Z

372

Water treatment method  

DOE Patents (OSTI)

A method is described for reducing the concentration of any undesirable metals dissolved in contaminated water, such as waste water. The method involves uniformly reacting the contaminated water with an excess amount of solid particulate calcium sulfite to insolubilize the undesirable metal ions, followed by removal thereof and of the unreacted calcium sulfite.

Martin, F.S.; Silver, G.L.

1991-04-30T23:59:59.000Z

373

Division of Water, Part 675: Great Lakes Water Withdrawal Registration...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

75: Great Lakes Water Withdrawal Registration Regulations (New York) Division of Water, Part 675: Great Lakes Water Withdrawal Registration Regulations (New York) Eligibility...

374

Carbon and Water Resource Management for Water Distribution Systems  

E-Print Network (OSTI)

5 March 2013. (12) Water Conservation Master Plan; East Baywww.ebmud.com/for-customers/water-conservation- rebates-and-services/water-conservation-master-plan, accessed 15

Hendrickson, Thomas Peter

2013-01-01T23:59:59.000Z

375

Water-Miscible (Water-Soluble) Fluids  

Science Conference Proceedings (OSTI)

...the growth of microorganisms such as bacteria, algae, and fungi. If disposal is of no concern, phenolics can be used. The soaps, wetting agents, and couplers used as emulsifiers in water-miscible fluids reduce surface

376

Water News | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Water News Water News Bioenergy Buildings Geothermal Government Energy Management Homes Hydrogen & Fuel Cells Advanced Manufacturing Solar Vehicles Water Wind Blog Archive Recent...

377

The economic conception of water  

E-Print Network (OSTI)

American City: municipal water supply investments. Ph. D.A . (2004). Boosting Water Productivity. In: Worldwatch1975). Issues in Village Water Supply. Washington, D . C ,

Hanemann, W. Michael

2005-01-01T23:59:59.000Z

378

Planning Water Use in California  

E-Print Network (OSTI)

the University of Maryland Water Policy Collaborative, 2006.FURTH ER READ ING California Department of Water Resources.California Water Plan Update 2005: A Framework for Action.

Eisenstein, William; Kondolf, G. Mathias

2008-01-01T23:59:59.000Z

379

Par Pond water balance  

SciTech Connect

A water budget for the Par Pond hydrologic system was established in order to estimate the rate of groundwater influx to Par Pond. This estimate will be used in modeling exercises to predict Par Pond reservoir elevation and spillway discharge in the scenario where Savannah River water is no longer pumped and discharged into Par Pond. The principal of conservation of mass was used to develop the water budget, where water inflow was set equal to water outflow. Components of the water budget were identified, and the flux associated with each was determined. The water budget was considered balanced when inflow and outflow summed to zero. The results of this study suggest that Par Pond gains water from the groundwater system in the upper reaches of the reservoir, but looses water to the groundwater system near the dam. The rate of flux of groundwater from the water table aquifer into Par Pond was determined to be 13 cfs. The rate of flux from Par Pond to the water table aquifer near the dam was determined to be 7 cfs.

Hiergesell, R.A.; Dixon, K.L.

1996-06-01T23:59:59.000Z

380

Water Heating | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Water Heating Water Heating Water Heating Infographic: Water Heaters 101 Everything you need to know about saving money on water heating costs Read more Selecting a New Water Heater Tankless? Storage? Solar? Save money on your water heating bill by choosing the right type of energy-efficient water heater for your needs. Read more Sizing a New Water Heater When buying a new water heater, bigger is not always better. Learn how to buy the right size of water heater. Read more You can reduce your monthly water heating bills by selecting the appropriate water heater for your home or pool and by using some energy-efficient water heating strategies. Some simple do-it-yourself projects, like insulating hot water pipes and lowering your water heating temperature, can also help you save money and energy on your water heating.

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Water Data Report: An Annotated Bibliography  

E-Print Network (OSTI)

Table 5: Public supply water withdrawals, 2000. water withdrawals, 2000. water withdrawals, 2000.

Dunham Whitehead, Camilla; Melody, Moya

2007-01-01T23:59:59.000Z

382

Water Heating | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Water Heating Water Heating August 19, 2013 - 11:15am Addthis A variety of systems are available for water heating in homes and buildings. Learn about: Conventional Storage Water...

383

Virginia Tech Hot Water Report  

NLE Websites -- All DOE Office Websites (Extended Search)

The team chose to use a water-to-water heat pump (WWHP) connected to an earth coupled heat exchanger to provide water heating. This system provides not only domestic hot water...

384

Water | OpenEI Community  

Open Energy Info (EERE)

Water Home Water Power Forum Description: Forum for information related to the Water Power Gateway The Water Power Community Forum provides you with a way to engage with other...

385

Ultrapdeep water blowouts: COMASim dynamic kill simulator validation and best practices recommendations  

E-Print Network (OSTI)

The petroleum industry is in a constant state of change. Few industries have advanced as far technologically as the petroleum industry has in its relatively brief existence. The produced products in the oil and gas industry are finite. As such, the easier to find and produce hydrocarbons are exploited first. This forces the industry to enter new areas and environments to continue supplying the world's hydrocarbons. Many of these new frontiers are in what is considered ultradeep waters, 5000 feet or more of water. While all areas of the oil and gas industry have advanced their ultradeep water technology, one area has had to remain at the forefront: drilling. Unfortunately, while drilling as a whole may be advancing to keep up with these environments, some segments lag behind. Blowout control is one of these areas developed as an afterthought. This lax attitude towards blowouts does not mean they are not a major concern. A blowout can mean injury or loss of life for rig personnel, as well as large economic losses, environmental damage and damage to the oil or gas reservoir itself. Obviously, up-to-date technology and techniques for the prevention and control of ultradeep water blowouts would be an invaluable part of any oil and gas company's exploration planning and technology suite. To further the development of blowout prevention and control, COMASim Cherokee Offshore, MMS, Texas A&M Simulator) was developed. COMASim simulates the planning and execution of a dynamic kill delivered to a blowout. Through a series of over 800 simulation runs, we were able to find several key trends in both the initial conditions as well as the kill requirements. The final phase of this study included a brief review of current industry deepwater well control best practices and how the COMASim results fit in with them. Overall, this study resulted in a better understanding of ultradeep water blowouts and what takes to control them dynamically. In addition to this understanding of blowouts, COMASim's strengths and weaknesses have now been exposed in order to further develop this simulator for industry use.

Noynaert, Samuel F.

2004-12-01T23:59:59.000Z

386

Stabilizing geometry for hydrodynamic rotary seals  

DOE Patents (OSTI)

A hydrodynamic sealing assembly including a first component having first and second walls and a peripheral wall defining a seal groove, a second component having a rotatable surface relative to said first component, and a hydrodynamic seal comprising a seal body of generally ring-shaped configuration having a circumference. The seal body includes hydrodynamic and static sealing lips each having a cross-sectional area that substantially vary in time with each other about the circumference. In an uninstalled condition, the seal body has a length defined between first and second seal body ends which varies in time with the hydrodynamic sealing lip cross-sectional area. The first and second ends generally face the first and second walls, respectively. In the uninstalled condition, the first end is angulated relative to the first wall and the second end is angulated relative to the second wall. The seal body has a twist-limiting surface adjacent the static sealing lip. In the uninstalled condition, the twist-limiting surface is angulated relative to the peripheral wall and varies along the circumference. A seal body discontinuity and a first component discontinuity mate to prevent rotation of the seal body relative to the first component.

Dietle, Lannie L. (Houston, TX); Schroeder, John E. (Richmond, TX)

2010-08-10T23:59:59.000Z

387

Rotary steerable motor system for underground drilling  

Science Conference Proceedings (OSTI)

A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

Turner, William E. (Durham, CT); Perry, Carl A. (Middletown, CT); Wassell, Mark E. (Kingwood, TX); Barbely, Jason R. (Middletown, CT); Burgess, Daniel E. (Middletown, CT); Cobern, Martin E. (Cheshire, CT)

2010-07-27T23:59:59.000Z

388

Continuous Flow Differential Pressure Rotary Transport ...  

This patent-pending active material transport system design concept provides solutions to several process challenges associated with moving materials ...

389

Publicly Submitted White Papers - Water  

Science Conference Proceedings (OSTI)

*. Bookmark and Share. Water. Advanced ... Strategies; AQUEOUS PHASE MERCURY REMOVAL: Strategies for a Secure Future Water Supply; ...

2012-08-01T23:59:59.000Z

390

Suppressant:Water & Aqueous Solutions  

Science Conference Proceedings (OSTI)

Suppressant:Water & Aqueous Solutions. ... Reuther, JJ; 1991. Fine Water Sprays for Fire Protection: A Halon Replacement Option.. ...

2011-10-28T23:59:59.000Z

391

Rethinking rig count as a predictor of natural gas production ...  

U.S. Energy Information Administration (EIA)

Uranium fuel, nuclear reactors, ... What is the role of coal in the United States? ... Using historical data ...

392

Flow field survey in a transonic compressor rig .  

E-Print Network (OSTI)

??As the Navy prepares to transition to F-35C Joint Strike Fighter the need to understand "pop stalls – caused by steam leakage in catapult systems is… (more)

Rose, Christopher W.

2006-01-01T23:59:59.000Z

393

Pad drilling and rig mobility lead to more efficient drilling ...  

U.S. Energy Information Administration (EIA)

Biofuels: Ethanol & Biodiesel ... Pad drilling allows producers to target a significant area of underground resources while minimizing impact on the surface.

394

Basic Rigging Workbook Training and Qualifications Program Office  

E-Print Network (OSTI)

................................................................................................................... 42 Carbon Steel Pipe Size Chart. This instructor handbook incorporates the Subject Area's requirements, as well as information from the Department

Homes, Christopher C.

395

Rigs Drilling Gas Wells Are At - Energy Information Administration  

U.S. Energy Information Administration (EIA)

The increasing number of resulting gas well completions have been expanding production in major producing States, such as Texas. For the year 2000, ...

396

Pad drilling and rig mobility lead to more efficient drilling ...  

U.S. Energy Information Administration (EIA)

Tools; Glossary › All Reports ... weather; gasoline; capacity; nuclear; exports; forecast; View All Tags ...

397

Rethinking rig count as a predictor of natural gas ...  

U.S. Energy Information Administration (EIA)

Includes hydropower, solar, wind, geothermal, biomass and ethanol. Nuclear & Uranium. Uranium fuel, nuclear reactors, generation, spent fuel. ... ...

398

Solar Water Heating  

NLE Websites -- All DOE Office Websites (Extended Search)

publication provides basic informa- publication provides basic informa- tion on the components and types of solar water heaters currently available and the economic and environmental benefits of owning a system. Although the publica- tion does not provide information on building and installing your own system, it should help you discuss solar water heating systems intelligently with a solar equipment dealer. Solar water heaters, sometimes called

399

Selecting a new water heater  

SciTech Connect

This fact sheet describes the types of water heaters available (storage water heaters, demand water heaters, heat pump water heaters, tankless coil and indirect water heaters, and solar water heaters). The criteria for selection are discussed. These are capacity, efficiency rating, and cost. A resource list is provided for further information.

NONE

1995-03-01T23:59:59.000Z

400

Water | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

daylighting, passive solar and active solar. They also have an 80 gallon solar hot water heater. | Photo by Dennis Schroeder, National Renewable Energy Laboratory. A guide to...

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Shield for Water Boiler  

SciTech Connect

Siimplified shielding calculations indicating the proposed design for the water boiler assembly will reduce the radiation at normal operaton to values well below those which are considered tolerable.

Balent, R.

1951-08-08T23:59:59.000Z

402

Saving Water Saves Energy  

E-Print Network (OSTI)

for Consumer Products: California Energy Commission PetitionCLOTHES_WASHERS.PDF> California Energy Commission. ApplianceMapTesting.lasso California Energy Commission, The Water

McMahon, James E.; Whitehead, Camilla Dunham; Biermayer, Peter

2006-01-01T23:59:59.000Z

403

Influence of Water Quality  

Science Conference Proceedings (OSTI)

...BP. Boffardi, Corrosion Inhibitors in the Water Treatment Industry, Corrosion: Fundamentals, Testing, and Protection, Vol 13A, ASM Handbook, ASM International, 2003, p 891â??906...

404

Cooling water distribution system  

DOE Patents (OSTI)

A passive containment cooling system for a nuclear reactor containment vessel. Disclosed is a cooling water distribution system for introducing cooling water by gravity uniformly over the outer surface of a steel containment vessel using an interconnected series of radial guide elements, a plurality of circumferential collector elements and collector boxes to collect and feed the cooling water into distribution channels extending along the curved surface of the steel containment vessel. The cooling water is uniformly distributed over the curved surface by a plurality of weirs in the distribution channels.

Orr, Richard (Pittsburgh, PA)

1994-01-01T23:59:59.000Z

405

ELDON water heater  

SciTech Connect

Experience with the installation of an ELDON water heater in the TLC Services, Inc. laundry facility is reported. Piping diagram and pictures are included. (MHR)

Wood, H.E.

1980-07-18T23:59:59.000Z

406

Water and Energy Interactions  

E-Print Network (OSTI)

technologies integrated with desalination systems. Renew.IC, Soldatos PG. 2008. Water desalination cost literature:review and assessment. Desalination 223(1–3): 448–56 107.

McMahon, James E.

2013-01-01T23:59:59.000Z

407

Water and Energy Interactions  

E-Print Network (OSTI)

oil recovery involves the injection of large quantities ofbarrel of oil equivalent (2). Although large quantities ofvarying, quantities of often low-quality water (2, 32). Oil

McMahon, James E.

2013-01-01T23:59:59.000Z

408

Water and Energy Interactions  

E-Print Network (OSTI)

Nuclear plants use steam turbines, and cooling water asmajority is used for steam-driven turbines, which generatedelectricity using steam engines, gas turbines, or Stirling

McMahon, James E.

2013-01-01T23:59:59.000Z

409

Salty Water Cerenkov Detectors  

E-Print Network (OSTI)

The addition of certain solutes to a water Cerenkov detector will introduce new charge-current channels for the detection of $\

W. C. Haxton

1995-11-28T23:59:59.000Z

410

Wool and Water.  

E-Print Network (OSTI)

?? Wool and Water is a creative work of 36 poems. This collection examines the relationship between the silent and vocal, between the pastoral and… (more)

Frederick, Kira

2009-01-01T23:59:59.000Z

411

Wool and water.  

E-Print Network (OSTI)

??Wool and Water is a creative work of 36 poems. This collection examines the relationship between the silent and vocal, between the pastoral and urban.… (more)

Frederick, Kira.

2009-01-01T23:59:59.000Z

412

UV Treated Water Dangers  

NLE Websites -- All DOE Office Websites (Extended Search)

there are chances of developing cancer or such growth due to radiation on drinking water & it's continuous intake? What are other hazards that may cause problems for human...

413

Supplying Water Social Studies  

NLE Websites -- All DOE Office Websites (Extended Search)

Handbook of Engaged Learning Projects SUPPLYING OUR WATER NEEDS: Africa Project Summary Scenario Student Pages References Index SubjectContent Area: World CulturesSocial Studies...

414

Saving Water Saves Energy  

E-Print Network (OSTI)

Test Procedure for Dishwashers, Federal Register, Vol. 68,e.g. , ,clothes washers or dishwashers that use less totalhes Washers Toilet s Dishwashers Figure 2a. Household Water

McMahon, James E.; Whitehead, Camilla Dunham; Biermayer, Peter

2006-01-01T23:59:59.000Z

415

Water and Energy Interactions  

E-Print Network (OSTI)

produced water into aging oil wells to help maximize oilpores until it reaches oil wells. This process can last forrock formations and reach oil wells. Using both processes,

McMahon, James E.

2013-01-01T23:59:59.000Z

416

OpenEI - Water  

Open Energy Info (EERE)

for years 1989 through 2010 for UT at Austin; specifically, electricity usage (kWh), natural gas usage (Mcf), associated costs. Also provides water consumption for 2005...

417

Water Heating Basics | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Heaters Solar Water Heaters Tankless Coil and Indirect Water Heaters Addthis Related Articles Tankless Demand Water Heater Basics Solar Water Heater Basics Heat Pump Water Heater...

418

Modeling 18° Water Variability  

Science Conference Proceedings (OSTI)

Variability of 18° Water formation is investigated with an isopycnic-coordinate model of the North Atlantic. A 30-year spinup integration is used as a “control” experiment in which the upper water column in the Sargasso Sea is shown to be in ...

Robert Marsh; Adrian L. New

1996-06-01T23:59:59.000Z

419

Purge water management system  

DOE Patents (OSTI)

A purge water management system for effectively eliminating the production of purge water when obtaining a groundwater sample from a monitoring well. In its preferred embodiment, the purge water management system comprises an expandable container, a transportation system, and a return system. The purge water management system is connected to a wellhead sampling configuration, typically permanently installed at the well site. A pump, positioned with the monitoring well, pumps groundwater through the transportation system into the expandable container, which expands in direct proportion with volume of groundwater introduced, usually three or four well volumes, yet prevents the groundwater from coming into contact with the oxygen in the air. After this quantity of groundwater has been removed from the well, a sample is taken from a sampling port, after which the groundwater in the expandable container can be returned to the monitoring well through the return system. The purge water management system prevents the purge water from coming in contact with the outside environment, especially oxygen, which might cause the constituents of the groundwater to oxidize. Therefore, by introducing the purge water back into the monitoring well, the necessity of dealing with the purge water as a hazardous waste under the Resource Conservation and Recovery Act is eliminated.

Cardoso-Neto, Joao E. (North Augusta, SC); Williams, Daniel W. (Aiken, SC)

1996-01-01T23:59:59.000Z

420

Purge water management system  

DOE Patents (OSTI)

A purge water management system is described for effectively eliminating the production of purge water when obtaining a groundwater sample from a monitoring well. In its preferred embodiment, the purge water management system comprises an expandable container, a transportation system, and a return system. The purge water management system is connected to a wellhead sampling configuration, typically permanently installed at the well site. A pump, positioned with the monitoring well, pumps groundwater through the transportation system into the expandable container, which expands in direct proportion with volume of groundwater introduced, usually three or four well volumes, yet prevents the groundwater from coming into contact with the oxygen in the air. After this quantity of groundwater has been removed from the well, a sample is taken from a sampling port, after which the groundwater in the expandable container can be returned to the monitoring well through the return system. The purge water management system prevents the purge water from coming in contact with the outside environment, especially oxygen, which might cause the constituents of the groundwater to oxidize. Therefore, by introducing the purge water back into the monitoring well, the necessity of dealing with the purge water as a hazardous waste under the Resource Conservation and Recovery Act is eliminated.

Cardoso-Neto, J.E.; Williams, D.W.

1995-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

Water Waves and Integrability  

E-Print Network (OSTI)

The Euler's equations describe the motion of inviscid fluid. In the case of shallow water, when a perturbative asymtotic expansion of the Euler's equations is taken (to a certain order of smallness of the scale parameters), relations to certain integrable equations emerge. Some recent results concerning the use of integrable equation in modeling the motion of shallow water waves are reviewed in this contribution.

Rossen I. Ivanov

2007-07-12T23:59:59.000Z

422

Drinking Water Problems: Nitrates  

E-Print Network (OSTI)

High levels of nitrates in drinking water can be harmful for very young infants and susceptible adults. This publication explains how people are exposed to nitrates, what health effects are caused by them in drinking water and how to remove them.

Dozier, Monty; Melton, Rebecca; Hare, Michael; Hopkins, Janie; Lesikar, Bruce J.

2008-03-28T23:59:59.000Z

423

Arkansas Water Resources Center  

E-Print Network (OSTI)

nutrients are available. Blowdown - the water discharged from a boiler or cooling tower to dispose and explains the procedures the owner/operator intends to take to perform assessment monitoring. Attenuation procedures. Equipotential Line - a line in a two-dimensional ground-water flow field such that the total

Soerens, Thomas

424

Water, Land and People  

NLE Websites -- All DOE Office Websites (Extended Search)

Water, Land and People Water, Land and People Nature Bulletin No. 251 January 8, 1983 Forest Preserve District of Cook County George W. Dunne, President Roland F. Eisenbeis, Supt. of Conservation WATER, LAND AND PEOPLE "Water, Land and People" is the title of a book which, like "Road to Survival", should be read by every American. Water, and its uses or control, has become a vital national problem. Some places, some years, we have too much of it and suffer disastrous floods. Elsewhere we have too little. In cities like New York and Los Angeles -- even in many inland towns -- and in the western lands which depend upon irrigation, the demand far exceeds the supply. Our Congress is beseeched for huge appropriations to provide flood control, navigation, electric power and irrigation.

425

Water Efficiency Program Prioritization  

NLE Websites -- All DOE Office Websites (Extended Search)

Efficiency Program Efficiency Program Prioritization Federal Energy Management Program Office of Energy Efficiency and Renewable Energy January 2009 Will Lintner (william.lintner@ee.doe.gov) Federal Energy Management The Goal - EO 13423 Beginning in 2008, Federal agencies must reduce water consumption intensity through life- effective measures, relative to the baseline of the agency's water consumption in fiscal year 2007 by 2 percent annually through the end of FY 2015 or 16 percent by the end of FY 2015. 2 Water Use Intensit ty (gal/sqft) Federal Sector Glide-Path to Meeting WUI Reduction Goal 55 50 45 40 35 30 25 20 FY 07 FY 08 FY 09 FY 10 FY 11 FY 12 FY 13 FY 14 FY 15 Total Federal sector FY07 WUI Glide-Path for meeting WUI reduction goal (16%) 3 Next Steps * Compile Water Data FY 2008. The baseline for water

426

INEEL Source Water Assessment  

SciTech Connect

The Idaho National Engineering and Environmental Laboratory (INEEL) covers approximately 890 mi2 and includes 12 public water systems that must be evaluated for Source water protection purposes under the Safe Drinking Water Act. Because of its size and location, six watersheds and five aquifers could potentially affect the INEEL’s drinking water sources. Based on a preliminary evaluation of the available information, it was determined that the Big Lost River, Birch Creek, and Little Lost River Watersheds and the eastern Snake River Plain Aquifer needed to be assessed. These watersheds were delineated using the United States Geologic Survey’s Hydrological Unit scheme. Well capture zones were originally estimated using the RESSQC module of the Environmental Protection Agency’s Well Head Protection Area model, and the initial modeling assumptions and results were checked by running several scenarios using Modflow modeling. After a technical review, the resulting capture zones were expanded to account for the uncertainties associated with changing groundwater flow directions, a thick vadose zone, and other data uncertainties. Finally, all well capture zones at a given facility were merged to a single wellhead protection area at each facility. A contaminant source inventory was conducted, and the results were integrated with the well capture zones, watershed and aquifer information, and facility information using geographic information system technology to complete the INEEL’s Source Water Assessment. Of the INEEL’s 12 public water systems, three systems rated as low susceptibility (EBR-I, Main Gate, and Gun Range), and the remainder rated as moderate susceptibility. No INEEL public water system rated as high susceptibility. We are using this information to develop a source water management plan from which we will subsequently implement an INEEL-wide source water management program. The results are a very robust set of wellhead protection areas that will protect the INEEL’s public water systems yet not too conservative to inhibit the INEEL from carrying out its missions.

Sehlke, Gerald

2003-03-01T23:59:59.000Z

427

Optimization of Chilled Water Systems  

E-Print Network (OSTI)

Chilled water systems are one of the major energy consumers in industrial, commercial, and institutional complexes. The centralization of chilled water systems presents numerous advantages, including simplified controls, reduced installation capacity due to diversity, and consolidated maintenance and operation. Centrally chilled water systems present potential energy and cost savings in the following areas: • Chilled water reset. • Condenser water reset. • Chiller sequencing. • Chilled water storage. • Variable chilled water pumping. The feasibility aspect of the above items will be discussed in this paper.

Gidwani, B. N.

1987-09-01T23:59:59.000Z

428

Pressurized Water Reactor Secondary Water Chemistry Guidelines – Revision 6  

Science Conference Proceedings (OSTI)

State-of-the-art water chemistry programs reduce equipment corrosion and enhance steam generator reliability. A committee of industry experts prepared these revised "Pressurized Water Reactor Secondary Water Chemistry Guidelines" to incorporate the latest field and laboratory data on secondary system corrosion and performance issues. Pressurized water reactor (PWR) operators can use these guidelines to update their secondary water chemistry programs.

2004-12-13T23:59:59.000Z

429

Recent California Water Transfers: Emerging Options in Water  

E-Print Network (OSTI)

IN TRANSFERS Recent years have produced increased interest in the transfer of water and waterRecent California Water Transfers: Emerging Options in Water Management by Jay R. Lund Associate for Environmental and Water Resources Engineering DEPARTMENT OF CIVIL AND ENVIRONMENTAL ENGINEERING University

Lund, Jay R.

430

A Membrane Process for Industrial Water Treatment: From Bench to Pilot Demonstration  

Science Conference Proceedings (OSTI)

A rotary membrane filtration system was used to separate die lubricant from a manufacturing wastewater stream consisting of various oils, hydrocarbons, heavy metals, and silicones. The ultrafiltration membranes reduced organics from initial oil and grease contents by factors of 20 to 25, carbon oxygen demand by 1.5 to 2, and total organic carbon by 0.6, while the biological oxygen demand remained constant. The rotary membranes were not fouled as badly as static membranes, and the rotary membrane flux levels were consistently higher and more stable than those of the static membranes tested. Field testing demonstrated that the rotary ultrafilter can concentrate the die lubricant, remove the glycerin component, and produce a die lubricant suitable for in-plant recycling. The recycling system operated for 6 weeks with only seven cleaning cycles and no mechanical or electrical failures. Test data and quality records indicate that when recycled die lubricant was used, the die casting scrap was reduced from 8.4 to 7.8%. Rotary ultrafiltration presents significant opportunities that can be evaluated further.

Eric S. Peterson; Bill Cleary; Michael Hackett; Jessica Trudeau

2005-01-01T23:59:59.000Z

431

WATER-TRAPPED WORLDS  

Science Conference Proceedings (OSTI)

Although tidally locked habitable planets orbiting nearby M-dwarf stars are among the best astronomical targets to search for extrasolar life, they may also be deficient in volatiles and water. Climate models for this class of planets show atmospheric transport of water from the dayside to the nightside, where it is precipitated as snow and trapped as ice. Since ice only slowly flows back to the dayside upon accumulation, the resulting hydrological cycle can trap a large amount of water in the form of nightside ice. Using ice sheet dynamical and thermodynamical constraints, I illustrate how planets with less than about a quarter the Earth's oceans could trap most of their surface water on the nightside. This would leave their dayside, where habitable conditions are met, potentially dry. The amount and distribution of residual liquid water on the dayside depend on a variety of geophysical factors, including the efficiency of rock weathering at regulating atmospheric CO{sub 2} as dayside ocean basins dry up. Water-trapped worlds with dry daysides may offer similar advantages as land planets for habitability, by contrast with worlds where more abundant water freely flows around the globe.

Menou, Kristen [Department of Astronomy, Columbia University, 550 West 120th Street, New York, NY 10027 (United States)

2013-09-01T23:59:59.000Z

432

The politics of water  

Science Conference Proceedings (OSTI)

Wars have been waged over oil and gold, but it is water that now poses the greatest potential for provoking conflict among nations-and the greatest need for new guarantees of cooperation. Athough water is a renewable resource, it is also a finite one. Nearly 40 percent of the world's population depends on river systems shared by two or more countries, leading to political hot spots, most critically in the middle east. This article describes in detail the water problems in the middle east, starting with the Jordan River basin, the Golan Heights, and the coastal aquifer, partly polluted. On the Sinai Peninsula the Nile River is the water source for nine countries, and the Tigris-Euphrates, although still providing water in relative abundance, is prey to the failure of Iraq, Syria, and Turkey to reach water-sharing agreements. Discussion includes the possibilities of turning the win-lose situations into win-win situations by appropriate water management and the problem of lack of a clear legal framework for settling disputes.

Postel, S.

1993-08-01T23:59:59.000Z

433

Water's Hydrogen Bond Strength  

E-Print Network (OSTI)

Water is necessary both for the evolution of life and its continuance. It possesses particular properties that cannot be found in other materials and that are required for life-giving processes. These properties are brought about by the hydrogen bonded environment particularly evident in liquid water. Each liquid water molecule is involved in about four hydrogen bonds with strengths considerably less than covalent bonds but considerably greater than the natural thermal energy. These hydrogen bonds are roughly tetrahedrally arranged such that when strongly formed the local clustering expands, decreasing the density. Such low density structuring naturally occurs at low and supercooled temperatures and gives rise to many physical and chemical properties that evidence the particular uniqueness of liquid water. If aqueous hydrogen bonds were actually somewhat stronger then water would behave similar to a glass, whereas if they were weaker then water would be a gas and only exist as a liquid at sub-zero temperatures. The overall conclusion of this investigation is that water's hydrogen bond strength is poised centrally within a narrow window of its suitability for life.

Martin Chaplin

2007-06-10T23:59:59.000Z

434

Brookhaven's Drinking-Water Quality  

NLE Websites -- All DOE Office Websites (Extended Search)

Water Quality Water Quality The Lab's finished drinking water is produced with pride by the staff of BNL's Water Treatment Facility Home Groundwater Consumer Confidence Reports Water Treatment Process Resources Tap Water Recommendations Water Cooler Cleaning Additional Resources Brookhaven Lab Drinking Water Brookhaven produces its own drinking water for all employees, facility-users, guests, residents, and visitors on site at its Water Treatment Facility (WTF). BNL's drinking water is pumped from groundwater by five active wells and processed at the WTF which can handle up to 6 million gallons per day. The "finished" water is sent to the Lab's two storage towers and then distributed around the site via 45 miles of pipeline. To ensure that Brookhaven's water meets all applicable local, state, and

435

Water Sampling | Open Energy Information  

Open Energy Info (EERE)

Water Sampling Water Sampling Jump to: navigation, search GEOTHERMAL ENERGYGeothermal Home Exploration Technique: Water Sampling Details Activities (51) Areas (45) Regions (5) NEPA(2) Exploration Technique Information Exploration Group: Field Techniques Exploration Sub Group: Field Sampling Parent Exploration Technique: Field Sampling Information Provided by Technique Lithology: Stratigraphic/Structural: Hydrological: Water composition and source of fluids Thermal: Water temperature Dictionary.png Water Sampling: Water sampling is done to characterize the chemical, thermal, or hydrological properties of a surface or subsurface aqueous system. Other definitions:Wikipedia Reegle Introduction Water sampling is done to characterize the geothermal system under investigation. A geothermal water typically has a unique chemical signature

436

Wind/Water Nexus  

DOE Green Energy (OSTI)

Nobel laureate Richard Smalley cited energy and water as among humanity's top problems for the next 50 years as the world's population increases from 6.3 billion to 9 billion. The U.S. Department of Energy's Wind and Hydropower Program has initiated an effort to explore wind energy's role as a technical solution to this critically important issue in the United States and the world. This four-page fact sheet outlines five areas in which wind energy can contribute: thermoelectric power plant/water processes, irrigation, municipal water supply, desalination, and wind/hydropower integration.

Not Available

2006-04-01T23:59:59.000Z

437

EXPERIMENTAL ANIMAL WATERING DEVICE  

SciTech Connect

A device for watering experimental animals confined in a battery of individual plastic enclosures is described. It consists of a rectangular plastic enclosure having a plurality of fluid-tight compartments, each with a drinking hole near the bottom and a filling hole on the top. The enclosure is immersed in water until filled, its drinking holes sealed with a strip of tape, and it is then placed in the battery. The tape sealing prevents the flow of water from the device, but permits animals to drink by licking the drinking holes. (AEC)

Finkel, M.P.

1964-04-01T23:59:59.000Z

438

Green Systems Solar Hot Water  

E-Print Network (OSTI)

Green Systems Solar Hot Water Heating the Building Co-generation: Heat Recovery System: Solar Thermal Panels (Trex enclosure) Hot Water Storage Tank (TS-5; basement) Hot Water Heaters (HW-1,2; basement) Pre-heats water so water heaters don't need to use as much energy Gas-powered, high efficiency

Schladow, S. Geoffrey

439

Burbank Water and Power - Solar Water Heater Rebate Program (California) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Burbank Water and Power - Solar Water Heater Rebate Program Burbank Water and Power - Solar Water Heater Rebate Program (California) Burbank Water and Power - Solar Water Heater Rebate Program (California) < Back Eligibility Residential Savings Category Heating & Cooling Solar Water Heating Program Info State California Program Type Utility Rebate Program Rebate Amount $1,500 Provider Rebates Burbank Water and Power is providing incentives for the purchase of solar water heaters. Incentives are only available to residential customers with electric water heaters. There is a limit of one solar water heater per year per property. Applicants must provide access to their residence for a pre-inspection to verify the existing use of an electric water heater. Customers must comply with all code and permit requirements. More

440

Water and Energy Interactions  

E-Print Network (OSTI)

US DOE). Energy Sources: Bioenergy. http://www.energy.gov/comparison of algae to other bioenergy feedstocks. Environ.The water footprint of bioenergy. Proc. Natl. Acad. Sci. USA

McMahon, James E.

2013-01-01T23:59:59.000Z

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Optimization of Cooling Water  

E-Print Network (OSTI)

A cooling water system can be optimized by operation at the highest possible cycles of concentration without risking sealing and fouling on heat exchanger surfaces. The way to optimize will be shown, with a number of examples of new systems.

Matson, J.

1985-05-01T23:59:59.000Z

442

Water | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Renewables » Water Renewables » Water Water EERE plays a key role in advancing America's "all of the above" energy strategy, leading a large network of researchers and other partners to deliver innovative technologies that will make renewable electricity generation cost-competitive with traditional sources of energy. EERE plays a key role in advancing America's "all of the above" energy strategy, leading a large network of researchers and other partners to deliver innovative technologies that will make renewable electricity generation cost-competitive with traditional sources of energy. Image of a buoy used for creating electricity from waves on the water. An american flag is attached to the top of the yellow buoy. The U.S. Department of Energy (DOE) leads the growing global effort to

443

Report on Produced Water  

NLE Websites -- All DOE Office Websites (Extended Search)

September 2009 Produced Water Volumes and Management Practices Page 3 Table of Contents Executive Summary ........................................................................................................................ 7 Chapter 1 - Introduction ............................................................................................................. 11 1.1 Purpose .......................................................................................................................... 11 1.2 Background ................................................................................................................... 11 1.3 Overview ....................................................................................................................... 11

444

Water and Energy Interactions  

E-Print Network (OSTI)

water from production of crude oil, natural gas, and coaleach gallon (3.79 liters) of crude oil. When combined withto refine each gallon of crude oil, between 3.6 and 7.0

McMahon, James E.

2013-01-01T23:59:59.000Z

445

Solar hot water heater  

SciTech Connect

A solar hot water heater includes an insulated box having one or more hot water storage tanks contained inside and further having a lid which may be opened to permit solar radiation to heat a supply of water contained within the one or more hot water storage tanks. A heat-actuated control unit is mounted on an external portion of the box, such control unit having a single pole double throw thermostat which selectively activates an electric winch gear motor to either open or close the box lid. The control unit operates to open the lid to a predetermined position when exposed to the sun's rays, and further operates to immediately close the lid in response to any sudden drop in temperature, such as might occur during a rainstorm, clouds moving in front of the sun, or the like.

Melvin, H.A.

1982-12-28T23:59:59.000Z

446

Water Treatment Plants  

NLE Websites -- All DOE Office Websites (Extended Search)

to see the operation than have us explain it. Basically, most treatment plants remove the solid material and use living organisms and chlorine to clean up the water. Steve Sample...

447

Water and Energy Interactions  

E-Print Network (OSTI)

past 15 years, nine solar thermal power plants, with a totala) colocating thermal power plants that use seawater forWater used in thermal electric power plants is extracted

McMahon, James E.

2013-01-01T23:59:59.000Z

448

UV water disinfector  

DOE Patents (OSTI)

A UV disinfector with a gravity driven feed water delivery system and an air-suspended bare UV lamp are disclosed. The disinfector is hydrodynamically optimized with a laminerizing, perforated baffle wall, beveled treatment chamber, and outlet weir. 7 figs.

Gadgil, A.; Garud, V.

1998-07-14T23:59:59.000Z

449

UV water disinfector  

DOE Patents (OSTI)

A UV disinfector with a gravity driven feed water delivery system, and an air-suspended bare UV lamp. The disinfector is hydrodynamically optimized with a laminerizing, perforated baffle wall, beveled treatment chamber, and outlet weir.

Gadgil, Ashok (El Cerrito, CA); Garud, Vikas (Bombay, IN)

1998-07-14T23:59:59.000Z

450

Water and Energy Interactions  

E-Print Network (OSTI)

opportunities at U.S. nuclear power plants. U.S. Dep. EnergyAlthough coal and nuclear power plants tend to supply baseis difficult to develop nuclear power plants in water-scarce

McMahon, James E.

2013-01-01T23:59:59.000Z

451

Water and Energy Interactions  

E-Print Network (OSTI)

US Dep. Energy, Washington, DC. http://www1.eere.energy.gov/Alliance Save Energy, Washington, DC. http://watergy.org/of Energy and Water. US DOE, Washington, DC. http://

McMahon, James E.

2013-01-01T23:59:59.000Z

452

Storm Water Detention Pond  

NLE Websites -- All DOE Office Websites (Extended Search)

allow water to meander through them. * Amend soil on the banks of the drainages with a compost-based soil builder. * Plant or stake the channel with with appropriate vegetation...

453

Contaminating Fresh Waters (Florida)  

Energy.gov (U.S. Department of Energy (DOE))

It is illegal to discharge any dyestuff, coal tar, oil, sawdust, poison, or deleterious substances into any fresh running waters in Florida in quantities sufficient to injure, stupefy, or kill fish...

454

Makeshift cold water aquarium  

NLE Websites -- All DOE Office Websites (Extended Search)

Location: NA Country: NA Date: NA Question: Hi- I am a student teacher in the Seattle area. As a hobby, I scuba dive in the icy waters of Puget Sound. I would love to set...

455

Water and Energy Interactions  

E-Print Network (OSTI)

oil, natural gas, and coal bed methane. Argonne Natl. Lab. ,gallons of water (31). Coal-bed methane, the availability ofnatural gas production. Coal-bed methane produces large, but

McMahon, James E.

2013-01-01T23:59:59.000Z

456

September 2004 Water Sampling  

Office of Legacy Management (LM)

was not identified at many groundwater locations. 18. Was the presence or absence of ice in the cooler documented at every sample location? Yes 19. Were water levels measured...

457

air_water.cdr  

Office of Legacy Management (LM)

Office of Legacy Management Weldon Spring Site Air and Water Monitoring 32008 This fact sheet provides information at Weldon Spring, Missouri. This site is managed by the U.S....

458

Arkansas Water Resources Center  

E-Print Network (OSTI)

Alluvial Aquifer, that has resulted from oil and gas operations in the area, particularly in south, discharge from poultry and hog plants, and leaky landfills, among others. Saline water intrusion and near

Soerens, Thomas

459

Water Heater Safety FAQs  

NLE Websites -- All DOE Office Websites (Extended Search)

from 30 gallons to 80 gallons in a variety of fuel sources (gas, electric, liquid propane). We also offer a wide selection of Rheem gas and electric tankless water heaters....

460

NETL: Water-Energy Interface - Power Plant Water Management  

NLE Websites -- All DOE Office Websites (Extended Search)

Transport Membrane Condenser for Water and Energy Recovery from Power Plant Flue Gas Gas Technology Institute (GTI) will develop a membrane separation technology to recover water...

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

IEP - Water-Energy Interface: Innovative Water Reuse and Recovery  

NLE Websites -- All DOE Office Websites (Extended Search)

is being performed in this program area to develop advanced technologies to reuse power plant cooling water and associated waste heat and to investigate methods to recover water...

462

NETL: Water-Energy Interface - Power Plant Water Management  

NLE Websites -- All DOE Office Websites (Extended Search)

Use of Produced Water in Recirculated Cooling Systems at Power Generating Facilities - EPRI The objective of this project is evaluation and development of the use of produced water...

463

Santa Clara Water & Sewer- Solar Water Heating Program  

Energy.gov (U.S. Department of Energy (DOE))

In 1975, the City of Santa Clara established the nation's first municipal solar utility. Under the Solar Water Heating Program, the Santa Clara Water & Sewer Utilities Department supplies,...

464

IEP - Water-Energy Interface: Cooling Water Intake Structures  

NLE Websites -- All DOE Office Websites (Extended Search)

The types of cooling water systems to be evaluated are: Wet Cooling Tower - The condenser is cooled with water recirculated to a mechanical draft cooling tower. Because there...

465

The Relationship between Water and Energy: Optimizing Water and Energy  

E-Print Network (OSTI)

In an effort to conserve water, drought-proof operating plants and control costs, the critical relationship of water and energy is clearly exposed. Five years of effort has transpired into countless studies, more than 100 projects and a clear understanding that the highest value opportunities for water conservation usually exist where there is the strongest interaction of water and energy. Steam management systems, process cooling, high quality water production and waste water treatment represent high probability areas for water conservation and value capture. These are not the only areas to reduce water management infrastructure and environmental footprint but they represent areas with the high potential for efforts to return bottom line value.

Finley, T.; Fennessey, K.; Light, R.

2007-01-01T23:59:59.000Z

466

A Realistic Hot Water Draw Specification for Rating Solar Water...  

NLE Websites -- All DOE Office Websites (Extended Search)

thornton@tess-inc.com ABSTRACT In the United States, annual performance ratings for solar water heaters are simulated, using TMY weather and specified water draw. Bias...

467

September 2004 Water Sampling  

Office of Legacy Management (LM)

3 3 Groundwater and Surface Water Sampling at the Slick Rock East and West, Colorado, Processing Sites November 2013 LMS/SRE/SRW/S0913 This page intentionally left blank U.S. Department of Energy DVP-September 2013, Slick Rock, Colorado November 2013 RIN 13095593 Page i Contents Sampling Event Summary ...............................................................................................................1 Slick Rock East and West, Colorado, Processing Sites, Sample Location Map .............................5 Data Assessment Summary ..............................................................................................................7 Water Sampling Field Activities Verification Checklist .............................................................9

468

September 2004 Water Sampling  

NLE Websites -- All DOE Office Websites (Extended Search)

3 3 Groundwater and Surface Water Sampling at the Tuba City, Arizona, Disposal Site November 2013 LMS/TUB/S00813 This page intentionally left blank U.S. Department of Energy DVP-August 2013, Tuba City, Arizona November 2013 RIN 13085553 Page i Contents Sampling Event Summary ...............................................................................................................1 Tuba City, Arizona, Disposal Site, Sample Location Map ..............................................................7 Data Assessment Summary ..............................................................................................................9 Water Sampling Field Activities Verification Checklist ...........................................................11

469

Water softening process  

DOE Patents (OSTI)

This invention involves an improved process for softening hard water which comprises selectively precipitaing CaCO.sub.3 to form a thin layer thereof, increasing the pH of said water to precipitate magnesium as magnesium hydroxide and then filtering the resultant slurry through said layer. The CaCO.sub.3 layer serves as a thin permeable layer which has particularly useful application in cross-flow filtration applications.

Sheppard, John D. (Oak Ridge, TN); Thomas, David G. (Oak Ridge, TN)

1976-01-01T23:59:59.000Z

470

Purifying contaminated water  

DOE Patents (OSTI)

Process for removing biorefractory compounds from contaminated water (e.g., oil shale retort waste-water) by contacting same with fragmented raw oil shale. Biorefractory removal is enhanced by preactivating the oil shale with at least one member of the group of carboxylic, acids, alcohols, aldehydes, ketones, ethers, amines, amides, sulfoxides, mixed ether-esters and nitriles. Further purification is obtained by stripping, followed by biodegradation and removal of the cells.

Daughton, Christian G. (San Pablo, CA)

1983-01-01T23:59:59.000Z

471

Water Cooling | Open Energy Information  

Open Energy Info (EERE)

Cooling: Cooling: Water cooling is commonly defined as a method of using water as a heat conduction to remove heat from an object, machine, or other substance by passing cold water over or through it. In energy generation, water cooling is typically used to cool steam back into water so it can be used again in the generation process. Other definitions:Wikipedia Reegle Water Cooling Typical water cooled condenser used for condensing steam Water or liquid cooling is the most efficient cooling method and requires the smallest footprint when cold water is readily available. When used in power generation the steam/vapor that exits the turbine is condensed back into water and reused by means of a heat exchanger. Water cooling requires a water resource that is cold enough to bring steam, typically

472

Water Heating | Department of Energy  

NLE Websites -- All DOE Office Websites (Extended Search)

need to know about saving money on water heating costs Read more Selecting a New Water Heater Tankless? Storage? Solar? Save money on your water heating bill by choosing the right...

473

FEMP-Solar Water Heating  

Energy.gov (U.S. Department of Energy (DOE))

Fact sheet details solar water heating and how to use the sun to heat domestic water in any climate. Document explains how solar water heating helps to save energy, reduce utility costs, and preserve the environment.

474

Clean Water Legacy Act (Minnesota)  

Energy.gov (U.S. Department of Energy (DOE))

This Act provides authority, direction, and resources to achieve and maintain water quality standards for groundwater and surface waters by implementing the federal Clean Water Act as well as...

475

NETL: Water-Energy Interface - Power Plant Water Management  

NLE Websites -- All DOE Office Websites (Extended Search)

Thermoelectric Power Plant Water Demands Using Alternative Water Supplies: Thermoelectric Power Plant Water Demands Using Alternative Water Supplies: Power Demand Options in Regions of Water Stress and Future Carbon Management Sandia National Laboratories (SNL) is conducting a regional modeling assessment of non-traditional water sources for use in thermoelectric power plants. The assessment includes the development of a model to characterize water quantity and quality from several sources of non-traditional water, initially focused within the Southeastern United States. The project includes four primary tasks: (1) identify water sources, needs, and treatment options; (2) assess and model non-traditional water quantity and quality; (3) identify and characterize water treatment options including an assessment of cost; and (4) develop a framework of metrics, processes, and modeling aspects that can be applied to other regions of the United States.

476

NETL: Water-Energy Interface - Power Plant Water Management  

NLE Websites -- All DOE Office Websites (Extended Search)

Internet-Based, GIS Catalog of Non-Traditional Sources of Cooling Water for Use at Coal-Fired Power Plants Internet-Based, GIS Catalog of Non-Traditional Sources of Cooling Water for Use at Coal-Fired Power Plants GIS Catalog Graphic Arthur Langhus Layne, LLC will create an internet-based, geographic information system (GIS) catalog of non-traditional sources of cooling water for coal-fired power plants. The project will develop data to identify the availability of oil and gas produced water, abandoned coal mine water, industrial waste water, and low-quality ground water. By pairing non-traditional water sources to power plant water needs, the research will allow power plants that are affected by water shortages to continue to operate at full-capacity without adversely affecting local communities or the environment. The nationwide catalog will identify the location, water withdrawal, and

477

Mitigation, Adaptation, Uncertainty -- Growing Water  

E-Print Network (OSTI)

UrbanLab is Sarah Dunn + Martin Felsen, with Lee Greenberg,Growing Water Martin Felsen and Sarah Dunn The Growing Water

Felsen, Martin; Dunn, Sarah

2008-01-01T23:59:59.000Z

478

Reading Comprehension - The Water Cycle  

NLE Websites -- All DOE Office Websites (Extended Search)

three phases that water can be found in are atom, molecule, compound solids, liquids, and gas . During condensation precipitation evaporation , water turns...

479

How Water Molecules are Connected  

NLE Websites -- All DOE Office Websites (Extended Search)

Science (Dec. 17, 2004) * *Online subscription needed. How Water Molecules are Connected Water may be the most important molecule on Earth, but our understanding of its properties...

480

Conservation of Water Resources (Virginia)  

Energy.gov (U.S. Department of Energy (DOE))

The State Water Control Board is responsible for formulating and implementing a comprehensive water use policy for the Commonwealth of Virginia. Implemented by the Department of Environmental...

Note: This page contains sample records for the topic "water rotary rig" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

Disinfecting Water after a Disaster  

E-Print Network (OSTI)

This publication explains how to disinfect water after a flood, as well as where to find water in an emergency when supplies are limited.

Dozier, Monty; Schoessow, Courtney

2005-09-30T23:59:59.000Z

482

NREL: Water Power Research - Projects  

NLE Websites -- All DOE Office Websites (Extended Search)

Search More Search Options Site Map Printable Version Projects NREL's water power R&D projects support industry efforts to develop and deploy cost-effective water power...

483

Columbia Water & Light- Solar Rebates  

Energy.gov (U.S. Department of Energy (DOE))

Columbia Water & Light (CWL) offers rebates to its commercial and residential customers for the purchase of solar water heaters and solar photovoltaic systems. These rebates are available for...

484

Water Heaters | Open Energy Information  

Open Energy Info (EERE)

Heaters Jump to: navigation, search TODO: Add description List of Water Heaters Incentives Retrieved from "http:en.openei.orgwindex.php?titleWaterHeaters&oldid267202...

485

Soil and Water Conservation (Indiana)  

Energy.gov (U.S. Department of Energy (DOE))

The Indiana Association of Soil and Water Conservation Districts is an association of the 92 soil and water conservation districts, each representing one of the 92 Indiana counties.

486

System for treating produced water  

DOE Patents (OSTI)

A system and method were used to treat produced water. Field-testing demonstrated the removal of contaminants from produced water from oil and gas wells.

Sullivan, Enid J. (Los Alamos, NM); Katz, Lynn (Austin, TX); Kinney, Kerry (Austin, TX); Bowman, Robert S. (Lemitar, NM); Kwon, Soondong (Kyungbuk, KR)

2010-08-03T23:59:59.000Z

487

Fluid Metrology Calibration Services - Water Flow  

Science Conference Proceedings (OSTI)

Fluid Metrology Calibration Services - Water Flow. Water Flow Calibrations 18020C. ... NIST provides calibration services for water flow meters. ...

2011-10-03T23:59:59.000Z

488

Pressurized Water Reactor Secondary Water Chemistry Guidelines - Revision 7  

Science Conference Proceedings (OSTI)

State-of-the-art water chemistry programs reduce equipment corrosion and enhance steam generator reliability. A committee of industry experts prepared these revised PWR Secondary Water Chemistry Guidelines to incorporate the latest field and laboratory data on secondary system corrosion and performance issues. Pressurized water reactor (PWR) operators can use these guidelines to update their secondary water chemistry programs.

2009-02-17T23:59:59.000Z

489

Regulations Establishing Water Quality Standards for Surface...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Establishing Water Quality Standards for Surface Water of the State of Arkansas (Arkansas) Regulations Establishing Water Quality Standards for Surface Water of the State of...

490

Colorado Ground Water Commission | Open Energy Information  

Open Energy Info (EERE)

Water Commission Jump to: navigation, search Name Colorado Ground Water Commission Place Colorado Website http:water.state.co.usgroun References Colorado Ground Water Commission...

491

Regulations Establishing Water Quality Standards for Surface Water of the  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Establishing Water Quality Standards for Surface Water Establishing Water Quality Standards for Surface Water of the State of Arkansas (Arkansas) Regulations Establishing Water Quality Standards for Surface Water of the State of Arkansas (Arkansas) < Back Eligibility Agricultural Commercial Construction Fed. Government Fuel Distributor General Public/Consumer Industrial Installer/Contractor Institutional Investor-Owned Utility Local Government Low-Income Residential Multi-Family Residential Municipal/Public Utility Nonprofit Residential Retail Supplier Rural Electric Cooperative Schools State/Provincial Govt Systems Integrator Transportation Tribal Government Utility Savings Category Water Buying & Making Electricity Home Weatherization Program Info State Arkansas Program Type Environmental Regulations Siting and Permitting

492

Water Usage Law, Major Water Users (Missouri) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Water Usage Law, Major Water Users (Missouri) Water Usage Law, Major Water Users (Missouri) Water Usage Law, Major Water Users (Missouri) < Back Eligibility Agricultural Commercial Construction Fed. Government Industrial Institutional Investor-Owned Utility Local Government Municipal/Public Utility Retail Supplier Rural Electric Cooperative Systems Integrator Tribal Government Utility Savings Category Water Buying & Making Electricity Program Info State Missouri Program Type Environmental Regulations Provider Missouri Department of Natural Resources Any water user with the capability to withdraw or divert 100,000 gallons or more per day from any stream, river, lake, well, spring or other water source must register and file for a permit for water withdrawal and diversion from the Department of Natural Resources. Additionally, no major

493

Water Transport Exploratory Studies  

NLE Websites -- All DOE Office Websites (Extended Search)

Exploratory Studies Exploratory Studies Office of Hydrogen, Fuel Cells, and Infrastructure Technologies 2007 kickoff meeting February 13-14, 2007 DOE Forrestal Building Rod Borup Mukundan Rangachary, Bryan Pivovar, Yu Seung Kim, John Davey, David Wood, Tom Springer, Muhammad Arif , Ken Chen, Simon Cleghorn, Will Johnson, Karren More, Peter Wilde, Tom Zawodzinski Los Alamos National Lab This presentation does not contain any proprietary or confidential information Objectives * Develop understanding of water transport in PEM Fuel Cells (non-design-specific) * Evaluate structural and surface properties of materials affecting water transport and performance * Develop (enable) new components and operating methods * Accurately model water transport within the fuel cell * Develop a better understanding of the effects of

494

Alternate Water Supply System  

Office of Legacy Management (LM)

Alternate Water Supply Alternate Water Supply System Flushing Report Riverton, Wyoming, Processing Site January 2008 Office of Legacy Management DOE M/1570 2008 - -L Work Performed Under DOE Contract No. for the U.S. Department of Energy Office of Legacy Management. DE-AC01-02GJ79491 Approved for public release; distribution is unlimited. Office of Legacy Management Office of Legacy Management Office of Legacy Management U.S. Department of Energy This page intentionally left blank DOE-LM/1570-2008 Alternate Water Supply System Flushing Report Riverton, Wyoming, Processing Site January 2008 Work Performed by S.M. Stoller Corporation under DOE Contract No. DE-AC01-02GJ79491 for the U.S. Department of Energy Office of Legacy Management, Grand Junction, Colorado This page intentionally left blank

495

Energy and Water Act  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Acquisition Letter 2004-02 - FY 2004 Le2islation Provisions (dated March 1.2004) Acquisition Letter 2004-02 - FY 2004 Le2islation Provisions (dated March 1.2004) Energy and Water Act AL-2004-02 provides guidance regarding the implementation of Section 30 I. 304. 307. 501,502, and Legislative Direction as provided in the Energy and Water Development Appropriation:) Act Pub. L, 108-137, also known as the E&W Act. RFP's for unfunded programs, UseJ' facilities, lobbying restrictions, and purchase of American made products are carried ovc:r from the FY 2003 Energy and Water Development Appropriations Act Pub, L, 108-7 {Division D), However, while the provision regarding competition still exists in the F'" 2004 legislation, the direction provided by Congress regarding the extend/compete process for 5 Management and Operating (M&O)contracts is

496

Biological denitrification of water  

SciTech Connect

The authors discuss research regarding the denitrification of drinking water. Most work has been done in Europe. As a consequence there may be a gap in the understanding of the international state of the art with regard to drinking-water denitrification. Numerous substrates have been evaluated including methanol, ethanol, acetic acid, methane, carbon monoxide, hydrogen, and various sulfur compounds. Various unit processes have been utilized including biofilters, fluidized-bed and packed-bed reactors, packed towers containing cells immobilized in polymer gels, and completely mixed reactors with cells attached to bouyant porous carriers. There are several commercial facilities currently providing drinking water to European communities. Most include post-treatment with flocculation, filtration, and disinfection. A common concern in denitrification operations is the minimization of nitrite accumulation.

Gayle, B.P. (Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (USA)); Boardman, G.D.; Sherrard, J.H. (Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (USA). Dept. of Civil Engineering); Benoit, R.E. (Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (USA). Dept. of Biology)

1989-10-01T23:59:59.000Z

497

Water, law, science  

SciTech Connect

In a world with water resources severely impacted bytechnology, science must actively contribute to water law. To this end,this paper is an earth scientist s attempt to comprehend essentialelements of water law, and to examine their connections to science.Science and law share a common logical framework of starting with apriori prescribed tenets, and drawing consistent inferences. In science,observationally established physical laws constitute the tenets, while inlaw, they stem from social values. The foundations of modern water law inEurope and the New World were formulated nearly two thousand years ago byRoman jurists who were inspired by Greek philosophy of reason.Recognizing that vital natural elements such as water, air, and the seawere governed by immutable natural laws, they reasoned that theseelements belonged to all humans, and therefore cannot be owned as privateproperty. Legally, such public property was to be governed by jusgentium, the law of all people or the law of all nations. In contrast,jus civile or civil law governed private property. Remarkably, jusgentium continues to be relevant in our contemporary society in whichscience plays a pivotal role in exploiting vital resources common to all.This paper examines the historical roots of modern water law, followstheir evolution through the centuries, and examines how the spirit ofscience inherent in jus gentium is profoundly influencing evolving waterand environmental laws in Europe, the United States and elsewhere. In atechnological world, scientific knowledge has to lie at the core of waterlaw. Yet, science cannot formulate law. It is hoped that a philosophicalunderstanding of the relationships between science and law willcontribute to their constructively coming together in the service ofsociety.

Narasimhan, T.N.

2007-10-17T23:59:59.000Z

498

Impacts of Water Quality on Residential Water Heating Equipment  

SciTech Connect

Water heating is a ubiquitous energy use in all residential housing, accounting for 17.7% of residential energy use (EIA 2012). Today, there are many efficient water heating options available for every fuel type, from electric and gas to more unconventional fuel types like propane, solar, and fuel oil. Which water heating option is the best choice for a given household will depend on a number of factors, including average daily hot water use (total gallons per day), hot water draw patterns (close together or spread out), the hot water distribution system (compact or distributed), installation constraints (such as space, electrical service, or venting accommodations) and fuel-type availability and cost. While in general more efficient water heaters are more expensive than conventional water heating technologies, the savings in energy use and, thus, utility bills can recoup the additional upfront investment and make an efficient water heater a good investment over time in most situations, although the specific payback period for a given installation will vary widely. However, the expected lifetime of a water heater in a given installation can dramatically influence the cost effectiveness and savings potential of a water heater and should be considered, along with water use characteristics, fuel availability and cost, and specific home characteristics when selecting the optimum water heating equipment for a particular installation. This report provides recommendations for selecting and maintaining water heating equipment based on local water quality characteristics.

Widder, Sarah H.; Baechler, Michael C.

2013-11-01T23:59:59.000Z

499

Water drives peptide conformational transitions  

E-Print Network (OSTI)

Transitions between metastable conformations of a dipeptide are investigated using classical molecular dynamics simulation with explicit water molecules. The distribution of the surrounding water at different moments before the transitions and the dynamical correlations of water with the peptide's configurational motions indicate that water is the main driving force of the conformational changes.

Nerukh, Dmitry

2011-01-01T23:59:59.000Z

500

Brief No. 9 WATER SECURITY,  

E-Print Network (OSTI)

Brief No. 9 WATER SECURITY, RISK & SOCIETY 1 of 4 Water Security and Federal Rivers March 2012 Australian National University Key messages · Water security in a hydroclimatic risk society. Climate risks interact with rapidly changing social, demographic and economic forces to position water security

New, Mark