Powered by Deep Web Technologies
Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


1

Wall Street vs. Main Street: Firm Strategies for Defending Legitimacy and Their Impact on Different Stakeholders  

Science Conference Proceedings (OSTI)

We assess the effect of firm strategies to defend legitimacy on two different stakeholder groups—the public (“Main Street”) and the investment community (“Wall Street”). We identify four types of firm strategies in response ... Keywords: crisis response, legitimacy, stakeholder theory, stigma management, thought worlds

Anna Lamin; Srilata Zaheer

2012-01-01T23:59:59.000Z

2

Simulation of terrace wall methane-steam reforming reactors  

Science Conference Proceedings (OSTI)

Terrace wall arrangement is one of the most common arrangements for methane-steam reforming reactor furnaces. In this work, a mathematical model of heat transfer in terrace wall furnaces has been developed. The model has been coupled with a reliable ... Keywords: heat transfer modeling, methane-steam reforming, reformer simulation, terrace wall furnace

J. S. Soltan Mohammadzadeh; A. Zamaniyan

2002-08-01T23:59:59.000Z

3

FIA-13-0006 - In the Matter of Wall Street Journal | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

6 - In the Matter of Wall Street Journal 6 - In the Matter of Wall Street Journal FIA-13-0006 - In the Matter of Wall Street Journal On May 24, 2013, the Office of Hearings and Appeals (OHA) issued a decision denying an appeal (Appeal) from a Freedom of Information Act (FOIA) determination issued by the Department of Energy's (DOE) Office of Information Resources (OIR). The Wall Street Journal, the Appellant, sought categories of records concerning IP addresses of computers that have accessed web pages administered by the DOE's Energy Information Administration (EIA) or on which data on energy resources are first made public by the EIA. In its partial response to the Appellant's request, the OIR withheld all IP addresses pursuant to Exemption 6. OIR stated that some of the withheld IP addresses would likely reveal the names of

4

Secretary Chu Op-Ed on Small Modular Reactors in the Wall Street Journal |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Op-Ed on Small Modular Reactors in the Wall Street Op-Ed on Small Modular Reactors in the Wall Street Journal Secretary Chu Op-Ed on Small Modular Reactors in the Wall Street Journal March 23, 2010 - 12:00am Addthis Washington, D.C. - Today, the Wall Street Journal published an op-ed by U.S. Secretary of Energy Steven Chu on small modular reactors. The op-ed can be viewed on the Wall Street Journal. The text of the op-ed is below: America's New Nuclear Option Small modular reactors will expand the ways we use atomic power. By Steven Chu Wall Street Journal, March 23, 2010 America is on the cusp of reviving its nuclear power industry. Last month President Obama pledged more than $8 billion in conditional loan guarantees for what will be the first U.S. nuclear power plant to break ground in nearly three decades. And with the new authority granted by the president's

5

Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Journal  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Journal Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Journal March 23, 2010 - 12:24pm Addthis Washington, D.C. - Today, the Wall Street Journal published an op-ed by U.S. Secretary of Energy Steven Chu on small modular reactors. The op-ed can be found here. The text of the op-ed is below: Small modular reactors will expand the ways we use atomic power. By Steven Chu, Secretary of Energy Wall Street Journal America is on the cusp of reviving its nuclear power industry. Last month President Obama pledged more than $8 billion in conditional loan guarantees for what will be the first U.S. nuclear power plant to break ground in nearly three decades. And with the new authority granted by the president's

6

Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Journal  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Journal Secretary Chu's Op-Ed on Small Modular Reactors in the Wall Street Journal March 23, 2010 - 12:24pm Addthis Washington, D.C. - Today, the Wall Street Journal published an op-ed by U.S. Secretary of Energy Steven Chu on small modular reactors. The op-ed can be found here. The text of the op-ed is below: Small modular reactors will expand the ways we use atomic power. By Steven Chu, Secretary of Energy Wall Street Journal America is on the cusp of reviving its nuclear power industry. Last month President Obama pledged more than $8 billion in conditional loan guarantees for what will be the first U.S. nuclear power plant to break ground in nearly three decades. And with the new authority granted by the president's

7

A Large-Eddy Simulation Study of Thermal Effects on Turbulent Flow and Dispersion in and above a Street Canyon  

Science Conference Proceedings (OSTI)

Thermal effects on turbulent flow and dispersion in and above an idealized street canyon with a street aspect ratio of 1 are numerically investigated using the parallelized large-eddy simulation model (“PALM”). Each of upwind building wall, street ...

Seung-Bu Park; Jong-Jin Baik; Siegfried Raasch; Marcus Oliver Letzel

2012-05-01T23:59:59.000Z

8

Street Trees and Intersection Safety  

E-Print Network (OSTI)

streets and the design of street lights on a typical street.Roadway signs: 10 feet • Street lights: 10 feet for palmlines: 5 feet Street lights: 15 feet Not specified Not

Macdonald, Elizabeth; Harper, Alethea; Williams, Jeff; Hayter, Jason A.

2006-01-01T23:59:59.000Z

9

Street Trees and Intersection Safety  

E-Print Network (OSTI)

streets and the design of street lights on a typical street.Roadway signs: 10 feet • Street lights: 10 feet for palmelectrical lines: 5 feet Street lights: 15 feet City of

Macdonald, Elizabeth; Harper, Alethea; Williams, Jeff; Hayter, Jason A.

2006-01-01T23:59:59.000Z

10

Catalytic Reforming  

Science Conference Proceedings (OSTI)

Don Little's Catalytic Reforming deals exclusively with reforming. With the increasing need for unleaded gasoline, the importance of this volume has escalated since it combines various related aspects of reforming technology into a single publication. For those with no practical knowledge of catalytic reforming, the chemical reactions, flow schemes and how the cat reformer fits into the overall refinery process will be of interest. Contents include: Catalytic reforming in refinery processing: How catalytic reformers work - chemical reactions; Process design; The catalyst, process variables and unit operation; Commercial processes; BTX operation; Feed preparation; naphtha hydrotreating and catalytic reforming; Index.

Little, D.M.

1985-01-01T23:59:59.000Z

11

Analysis of Chemically Reacting Gas Flow and Heat Transfer in Methane Reforming Processes  

Science Conference Proceedings (OSTI)

This paper presents simulation and analysis of gas flow and heat transfer affected by chemical reactions relating to steam reforming of methane in a compact reformer. The reformer conditions such as the combined thermal boundary conditions on solid walls, ...

Guogang Yang; Danting Yue; Xinrong Lv; Jinliang Yuan

2009-10-01T23:59:59.000Z

12

Making Streets that Work [Streets: Old Paradigm, New Investment  

E-Print Network (OSTI)

components as varied as street lights, trash cans ands / S E D Street l i g h t i n g / S E D , City Light D C L

Sellin, Dennis

1997-01-01T23:59:59.000Z

13

Catalytic reforming  

Science Conference Proceedings (OSTI)

This patent describes a process for the catalytic reforming of a feedstock which contains at least one reformable organic compound. The process consists of contacting the feedstock under suitable reforming conditions with a catalyst composition selected from the group consisting of a catalyst. The catalyst essentially consists of zinc oxide and a spinel structure alumina. Another catalyst consists essentially of a physical mixture of zinc titanate and a spinel structure alumina in the presence of sufficient added hydrogen to substantially prevent the formation of coke. Insufficient zinc is present in the catalyst composition for the formation of a bulk zinc aluminate.

Aldag, A.W. Jr.

1986-01-28T23:59:59.000Z

14

The solar LED street light.  

E-Print Network (OSTI)

??The purpose of this essay is to analyze the component of the solar LED street lighting, such as structure, principle, characteristics and precautions for installation… (more)

Ma, Hao

2013-01-01T23:59:59.000Z

15

200 N. Spring Street  

Office of Legacy Management (LM)

Dipartment of Energy. ,' Dipartment of Energy. ,' Washington,DC20585 ., .\ FEB 1 7 ' 19g5' ,The Honorable Richa,rd. Riordon .', 200 N. Spring Street 'Los Angeles, California ,90012 '~ Dear Mayor Riordon: " Secretary of Energy Hazel O'Leary'has announced a neb approach to openness ins- the Department of Energy (DOE) and its communications with the public. fin support of this initiative, we are pleased~ to forward the enclosed information related to the. former Shannon Luminous Metals site in your jurisdiction that pe.rformed work for DOE's'predecessor agencies.' .This'information is provided foryour information, use! and,retention.~' "I , DOE's Formerly.Utilized Sites Remedial Action Program (FUSRAP) is responsible for identification of, sites used by DOE's predecessor agencies, determining

16

A Numerical Study of Thermal Effects on Flow and Pollutant Dispersion in Urban Street Canyons  

Science Conference Proceedings (OSTI)

This study investigates thermal effects on the flow and pollutant dispersion in urban street canyons. A two-dimensional numerical model with a k–? turbulent closure scheme is developed, and the heat transfer between the air and the building wall ...

Jae-Jin Kim; Jong-Jin Baik

1999-09-01T23:59:59.000Z

17

Energy management in municipal street lighting  

SciTech Connect

This report presents strategies to reduce the energy used in street lighting and, at the same time, reduce or stabilize the cost of street lighting to municipalities.

1977-03-01T23:59:59.000Z

18

Hydrocarbon reforming catalyst material and configuration of the same  

DOE Patents (OSTI)

A hydrocarbon reforming catalyst material comprising a catalyst support impregnated with catalyst is provided for reforming hydrocarbon fuel gases in an electrochemical generator. Elongated electrochemical cells convert the fuel to electrical power in the presence of an oxidant, after which the spent fuel is recirculated and combined with a fresh hydrocarbon feed fuel forming the reformable gas mixture which is fed to a reforming chamber containing a reforming catalyst material, where the reforming catalyst material includes discrete passageways integrally formed along the length of the catalyst support in the direction of reformable gas flow. The spent fuel and/or combusted exhaust gases discharged from the generator chamber transfer heat to the catalyst support, which in turn transfers heat to the reformable gas and to the catalyst, preferably via a number of discrete passageways disposed adjacent one another in the reforming catalyst support. The passageways can be slots extending inwardly from an outer surface of the support body, which slots are partly defined by an exterior confining wall. According to a preferred embodiment, the catalyst support is non-rigid, porous, fibrous alumina, wherein the fibers are substantially unsintered and compressible, and the reforming catalyst support is impregnated, at least in the discrete passageways with Ni and MgO, and has a number of internal slot passageways for reformable gas, the slot passageways being partly closed by a containing outer wall. 5 figs.

Singh, P.; Shockling, L.A.; George, R.A.; Basel, R.A.

1996-06-18T23:59:59.000Z

19

Hydrocarbon reforming catalyst material and configuration of the same  

DOE Patents (OSTI)

A hydrocarbon reforming catalyst material comprising a catalyst support impregnated with catalyst is provided for reforming hydrocarbon fuel gases in an electrochemical generator. Elongated electrochemical cells convert the fuel to electrical power in the presence of an oxidant, after which the spent fuel is recirculated and combined with a fresh hydrocarbon feed fuel forming the reformable gas mixture which is fed to a reforming chamber containing a reforming catalyst material, where the reforming catalyst material includes discrete passageways integrally formed along the length of the catalyst support in the direction of reformable gas flow. The spent fuel and/or combusted exhaust gases discharged from the generator chamber transfer heat to the catalyst support, which in turn transfers heat to the reformable gas and to the catalyst, preferably via a number of discrete passageways disposed adjacent one another in the reforming catalyst support. The passageways can be slots extending inwardly from an outer surface of the support body, which slots are partly defined by an exterior confining wall. According to a preferred embodiment, the catalyst support is non-rigid, porous, fibrous alumina, wherein the fibers are substantially unsintered and compressible, and the reforming catalyst support is impregnated, at least in the discrete passageways with Ni and MgO, and has a number of internal slot passageways for reformable gas, the slot passageways being partly closed by a containing outer wall.

Singh, Prabhakar (Export, PA); Shockling, Larry A. (Plum Borough, PA); George, Raymond A. (Pittsburgh, PA); Basel, Richard A. (Plub Borough, PA)

1996-01-01T23:59:59.000Z

20

The Recovery Act is "Lighting Up" the streets of Philadelphia...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Recovery Act is "Lighting Up" the streets of Philadelphia The Recovery Act is "Lighting Up" the streets of Philadelphia Addthis Description The Philadelphia Streets Department...

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


21

Incorporating video into Google Mobile Street View  

E-Print Network (OSTI)

Mobile Street View is a compelling application but suffers from significant latency problems, especially in limited bandwidth circumstances. Currently, the application uses static images to display street level information. ...

Wright, Christina (Christina E.)

2010-01-01T23:59:59.000Z

22

Physical Modeling of Flow Field inside Urban Street Canyons  

Science Conference Proceedings (OSTI)

The flow characteristics inside urban street canyons were studied in a laboratory water channel. The approaching flow direction was horizontal and perpendicular to the street axis. The street width was adjusted to form street canyons of aspect ...

Xian-Xiang Li; Dennis Y. C. Leung; Chun-Ho Liu; K. M. Lam

2008-07-01T23:59:59.000Z

23

Brighter Lights, Safer Streets | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Brighter Lights, Safer Streets May 15, 2012 - 5:56pm Addthis Workers install the final LED streetlight for DC's EECBG-funded energy efficient lighting upgrade. | Energy...

24

FranklinAvenue SouthDepysterStreet  

E-Print Network (OSTI)

Grille F10 Pita Pit F11 Bu alo Wild Wings F12 College Creamery F13 Euro Gyro F14 College Coneys F15 Taco (one way tra c) foottraconlyfoottraconly SouthWaterStreetNorthWaterStreet Red listings, see map

Palffy-Muhoray, Peter

25

Information Resources: Adaptive Street Lighting Controls  

NLE Websites -- All DOE Office Websites (Extended Search)

Adaptive Street Lighting Controls Adaptive Street Lighting Controls This two-part DOE Municipal Solid-State Street Lighting Consortium webinar focused on LED street lighting equipped with adaptive control components. In Part I, presenters Amy Olay of the City of San Jose, CA, and Kelly Cunningham of the California Lighting Technology Center at UC Davis discussed their experiences as early adopters of these smart street lighting systems. In Part II, presenters Laura Stuchinsky of the City of San Jose, CA, and Michael Poplawski of Pacific Northwest National Laboratory explored the MSSLC's recently released Model Specification for Adaptive Control and Remote Monitoring of LED Roadway Luminaires. Part I: Experiences and Benefits June 11, 2013 View the presentation slides Part II: Reviewing the MSSLC's Model Specification

26

Cleaning up the Streets of Denver  

Science Conference Proceedings (OSTI)

Between 1913 and 1924, several Denver area facilities extracted radium from carnotite ore mined from the Paradox basin region of Colorado. Tailings or abandoned ores from these facilities were apparently incorporated into asphalt used to pave approximately 7.2 kilometers (4.5 miles) of streets in Denver. A majority of the streets are located in residential areas. The radionuclides are bound within the asphalt matrix and pose minimal risk unless they are disturbed. The City and County of Denver (CCoD) is responsible for controlling repairs and maintenance on these impacted streets. Since 2002, the CCoD has embarked on a significant capital improvement project to remove the impacted asphalt for secure disposal followed by street reconstruction. To date, Parsons has removed approximately 55 percent of the impacted asphalt. This paper discusses the history of the Denver Radium Streets and summarizes on-going project efforts. (authors)

Stegen, R.L.; Wood, T.R.; Hackett, J.R. [Parsons, 1700 Broadway, Suite 900, Denver, Colorado 80290 (United States); Sogue, A. [City and County of Denver, 201 West Colfax, Denver, Colorado 80202 (United States)

2006-07-01T23:59:59.000Z

27

Process for catalytic reforming  

Science Conference Proceedings (OSTI)

An improved catalytic reforming process is disclosed wherein hydrogen and light hydrocarbons generated in the catalytic reaction zone are passed to a hydrogen production/purification zone and and reacted and processed therein to produce substantially pure hydrogen. A portion of the hydrogen is then admixed with the charge stock to the catalytic reforming zone to provide the hydrogen requirements of the catalytic reforming reaction zone.

James, R. B. Jr.

1984-11-20T23:59:59.000Z

28

Boulevard Livability Study [Streets: Old Paradigm, New Investment  

E-Print Network (OSTI)

whereas the medium and light control streets ranged from 70OCEAN PKWY EASTERN PKWY LIGHT STREET boulevards. M o r eeach direction and the light streets just one lane i n each

Bosselmann, Peter; Macdonald, Elizabeth

1997-01-01T23:59:59.000Z

29

Systemic Reform Bibliography  

NLE Websites -- All DOE Office Websites (Extended Search)

(5) support local initiatives and model sites; (6) align state policy; (7) reform higher education and teacher preparation; and (8) mobilize public and professional...

30

Plasma—Methane Reformation  

INL thermal plasma methane reformation process produces hydrogen and elemental carbon from natural gas and other hydrocarbons, such as natural gas or ...

31

Catalytic reforming process  

Science Conference Proceedings (OSTI)

A catalytic reforming process is disclosed in which substantially all of the heat requirements of the product stabilizer column is supplied by multiple indirect heat exchange.

Peters, K.D.

1983-10-11T23:59:59.000Z

32

The Recovery Act is "Lighting Up" the streets of Philadelphia...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Marketing Administration Other Agencies You are here Home The Recovery Act is "Lighting Up" the streets of Philadelphia The Recovery Act is "Lighting Up" the streets of...

33

Gas, Heat, Water, Sewerage Collection and Disposal, and Street...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Gas, Heat, Water, Sewerage Collection and Disposal, and Street Railway Companies (South Carolina) Gas, Heat, Water, Sewerage Collection and Disposal, and Street Railway Companies...

34

Electric, Gas, Water, Heating, Refrigeration, and Street Railways...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

and Street Railways Facilities and Service (South Dakota) Electric, Gas, Water, Heating, Refrigeration, and Street Railways Facilities and Service (South Dakota) < Back...

35

Street and Parking Facility Lighting Retrofit Financial Analysis...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Street and Parking Facility Lighting Retrofit Financial Analysis Tool Webinar Street and Parking Facility Lighting Retrofit Financial Analysis Tool Webinar August 22, 2013 1:00PM...

36

Solid-State Lighting: Webcast: Evaluating LED Street Lighting...  

NLE Websites -- All DOE Office Websites (Extended Search)

Webcast: Evaluating LED Street Lighting Solutions to someone by E-mail Share Solid-State Lighting: Webcast: Evaluating LED Street Lighting Solutions on Facebook Tweet about...

37

Security and Suitability Process Reform  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Security and Suitability Process Reform December 2008 Provided by the Joint Security and Suitability Reform Team EXECUTIVE OFFICE OF THE PRESIDENT OFFICE OF MANAGEMENT AND BUDGET...

38

Copyright reform step zero  

Science Conference Proceedings (OSTI)

'A reasonable person might well think it's a fool's errand to contemplate a [copyright] reform project of any sort.' The US Copyright Act of 1976 and its subsequent amendments is contained in over 200 pages of incomprehensible, sometimes inconsistent, ... Keywords: US copyright law, administrative law, copyright reform, institutional frameworks

Terry Hart

2010-06-01T23:59:59.000Z

39

Catalytic reforming process  

Science Conference Proceedings (OSTI)

A catalytic reforming process is disclosed wherein the reboiler heat requirements of the stabilizer column are supplied by means of indirect heat exchange with hot combustion gases in the reforming reactants fired heater convection heating section. Heat in excess of the reboiler requirements is passed to the stabilizer column with control being effected by removal of excess heat from the column.

James, R.B. Jr.

1984-02-14T23:59:59.000Z

40

Solid-State Lighting: Adaptive Street Lighting Controls  

NLE Websites -- All DOE Office Websites (Extended Search)

Adaptive Street Lighting Adaptive Street Lighting Controls to someone by E-mail Share Solid-State Lighting: Adaptive Street Lighting Controls on Facebook Tweet about Solid-State Lighting: Adaptive Street Lighting Controls on Twitter Bookmark Solid-State Lighting: Adaptive Street Lighting Controls on Google Bookmark Solid-State Lighting: Adaptive Street Lighting Controls on Delicious Rank Solid-State Lighting: Adaptive Street Lighting Controls on Digg Find More places to share Solid-State Lighting: Adaptive Street Lighting Controls on AddThis.com... Conferences & Meetings Presentations Publications Webcasts Videos Tools Adaptive Street Lighting Controls This two-part DOE Municipal Solid-State Street Lighting Consortium webinar focused on LED street lighting equipped with adaptive control components.

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


41

2009 Takin' it to the Streets Campaign  

Energy.gov (U.S. Department of Energy (DOE))

The objective of the Summer Takin’ It to the Streets awareness campaign is to reinforce awareness and understanding by informing DOE employees and general users about best practices to prevent,...

42

California Street Biomass Facility | Open Energy Information  

Open Energy Info (EERE)

Street Biomass Facility Street Biomass Facility Jump to: navigation, search Name California Street Biomass Facility Facility California Street Sector Biomass Facility Type Landfill Gas Location San Bernardino County, California Coordinates 34.9592083°, -116.419389° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":34.9592083,"lon":-116.419389,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

43

Manhattan Project: Los Alamos Street Scene  

Office of Scientific and Technical Information (OSTI)

LOS ALAMOS STREET SCENE LOS ALAMOS STREET SCENE Los Alamos (The Town) Resources > Photo Gallery Los Alamos street scene. Fuller Lodge and the "Big House" are visible in the distance (see below). Above is a view of Los Alamos (looking north). In the distance, Fuller Lodge and the "Big House" are visible to the left and right, respectively (see below). The photograph is reproduced from Los Alamos Scientific Laboratory, Los Alamos: Beginning of an Era, 1943-1945 (Los Alamos: Public Relations Office, Los Alamos Scientific Laboratory, ca. 1967-1971), 13. The labels and "close-ups" below were made by the Office of History and Heritage Resources. Los Alamos street scene (labeled) Close-up of Fuller Lodge Close-up of the "Big House" Click on a link below to return to:

44

Main Street Loan Program (North Dakota)  

Energy.gov (U.S. Department of Energy (DOE))

The Main Street Loan Program loans of up to $24,999 through the Certified Development Corporation (CDC) in participation with local lenders or economic development organizations for small...

45

July 18, 2012 Using QECBs for Street Lighting Upgrades  

E-Print Network (OSTI)

lighting technologies (e.g. light-emitting diodes, induction lighting) can reduce street light energy

46

Catalytic reforming methods  

DOE Patents (OSTI)

A catalytic reforming method is disclosed herein. The method includes sequentially supplying a plurality of feedstocks of variable compositions to a reformer. The method further includes adding a respective predetermined co-reactant to each of the plurality of feedstocks to obtain a substantially constant output from the reformer for the plurality of feedstocks. The respective predetermined co-reactant is based on a C/H/O atomic composition for a respective one of the plurality of feedstocks and a predetermined C/H/O atomic composition for the substantially constant output.

Tadd, Andrew R; Schwank, Johannes

2013-05-14T23:59:59.000Z

47

Numerical simulation of micro/mini-channel based methane-steam reformer.  

E-Print Network (OSTI)

??Numerical modeling of methane-steam reforming is performed in a micro/mini-channel with heat input through catalytic channel walls. The low-Mach number, variable density Navier-Stokes equations together… (more)

[No author

2010-01-01T23:59:59.000Z

48

Main Street Multidisciplinary Practice Firms: Laboratories for the Future  

E-Print Network (OSTI)

file with the University of Michigan Journal of Law Reform).8:38 AM University of Michigan Journal of Law Reform [Vol.file with the University of Michigan Journal of Law Reform).

Poser, Susan

2004-01-01T23:59:59.000Z

49

Multizone naphtha reforming process  

Science Conference Proceedings (OSTI)

This patent describes a catalytic reforming process for conversion of a naphtha hydrocarbon at reforming conditions having at least two segregated catalyst zones. The improvement comprises contacting the hydrocarbon in a first zone with a first catalyst comprising tin and at least one platinum group metal deposited on a solid catalyst support followed by contacting in a second zone with a second catalyst comprising at least one metal selected from the group consisting of platinum group metals deposited on a solid catalyst support.

Fleming, B.

1987-05-05T23:59:59.000Z

50

Comparing Light Emitting Diode (LED) Street and Area Lighting to Traditional Lighting Technologies  

Science Conference Proceedings (OSTI)

High-power light-emitting diode (LED) technology holds great promise for outdoor illumination. This case study discusses the results of the LED Street and Area Lighting Demonstration performed by Tennessee Valley Authority (TVA), Knoxville Utilities Board (KUB), and EPRI. Data was collected on Wall Avenue, a busy thoroughfare in downtown Knoxville, using a specially developed computer-controlled mobile light measurement vehicle with a global positioning system.Early reports from the ...

2012-09-28T23:59:59.000Z

51

Brighter Lights, Safer Streets | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Brighter Lights, Safer Streets Brighter Lights, Safer Streets Brighter Lights, Safer Streets May 15, 2012 - 5:56pm Addthis Workers install the final LED streetlight for DC's EECBG-funded energy efficient lighting upgrade. | Energy Department photo, credit Chris Galm. Workers install the final LED streetlight for DC's EECBG-funded energy efficient lighting upgrade. | Energy Department photo, credit Chris Galm. Chris Galm Marketing & Communications Specialist, Office of Energy Efficiency & Renewable Energy What does this project do? DC's streetlight upgrades will save approximately $59,000 in energy costs every year -- in addition to the reduced maintenance and replacement costs. The new lights will also cut greenhouse gas emissions by 719 tons. Thanks to support from an Energy Department Recovery Act grant, Washington,

52

Electrochemical fuel cell generator having an internal and leak tight hydrocarbon fuel reformer  

DOE Patents (OSTI)

An electrochemical fuel cell generator configuration is made having a generator section which contains a plurality of axially elongated fuel cells, each cell containing a fuel electrode, air electrode, and solid oxide electrolyte between the electrodes, in which axially elongated dividers separate portions of the fuel cells from each other, and where at least one divider also reforms a reformable fuel gas mixture prior to electricity generation reactions, the at least one reformer-divider is hollow having a closed end and an open end entrance for a reformable fuel mixture to pass to the closed end of the divider and then reverse flow and pass back along the hollowed walls to be reformed, and then finally to pass as reformed fuel out of the open end of the divider to contact the fuel cells, and further where the reformer-divider is a composite structure having a gas diffusion barrier of metallic foil surrounding the external walls of the reformer-divider except at the entrance to prevent diffusion of the reformable gas mixture through the divider, and further housed in an outer insulating jacket except at the entrance to prevent short-circuiting of the fuel cells by the gas diffusion barrier. 10 figs.

Dederer, J.T.; Hager, C.A.

1998-03-31T23:59:59.000Z

53

Electrochemical fuel cell generator having an internal and leak tight hydrocarbon fuel reformer  

DOE Patents (OSTI)

An electrochemical fuel cell generator configuration is made having a generator section which contains a plurality of axially elongated fuel cells, each cell containing a fuel electrode, air electrode, and solid oxide electrolyte between the electrodes, in which axially elongated dividers separate portions of the fuel cells from each other, and where at least one divider also reforms a reformable fuel gas mixture prior to electricity generation reactions, the at least one reformer-divider is hollow having a closed end and an open end entrance for a reformable fuel mixture to pass to the closed end of the divider and then reverse flow and pass back along the hollowed walls to be reformed, and then finally to pass as reformed fuel out of the open end of the divider to contact the fuel cells, and further where the reformer-divider is a composite structure having a gas diffusion barrier of metallic foil surrounding the external walls of the reformer-divider except at the entrance to prevent diffusion of the reformable gas mixture through the divider, and further housed in an outer insulating jacket except at the entrance to prevent short-circuiting of the fuel cells by the gas diffusion barrier.

Dederer, Jeffrey T. (Valencia, PA); Hager, Charles A. (Mars, PA)

1998-01-01T23:59:59.000Z

54

Retrofitting Urban Arterials Into Complete Streets  

E-Print Network (OSTI)

speeds reduce mobility and increase costs for all vehicles Required to design to Level of Service C with Federal highway standards and guidelines Slower speeds reduce mobility and increase costs for all in Complete Streets Conflicts with National Guidelines #12;ITE New Recommended Practice Designing Walkable

Bertini, Robert L.

55

Lighting the Night: Technology, Urban Life and the Evolution of Street Lighting [Light in Place  

E-Print Network (OSTI)

May 1912), 783. 8. "New Street Lights Increase Trade 3 5 Perlight, including street light, became part of America'sBeautiful-inspired street­ lights graced wealthy residen­

Holden, Alfred

1992-01-01T23:59:59.000Z

56

The National Science Bowl Students are Here! (The Streets of...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The National Science Bowl Students are Here (The Streets of D.C. Just Got a Little Smarter.) The National Science Bowl Students are Here (The Streets of D.C. Just Got a Little...

57

Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air  

Alternative Fuels and Advanced Vehicles Data Center (EERE)

Natural Gas Street Natural Gas Street Sweepers Improve Air Quality in New York to someone by E-mail Share Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air Quality in New York on Facebook Tweet about Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air Quality in New York on Twitter Bookmark Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air Quality in New York on Google Bookmark Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air Quality in New York on Delicious Rank Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air Quality in New York on Digg Find More places to share Alternative Fuels Data Center: Natural Gas Street Sweepers Improve Air Quality in New York on AddThis.com...

58

Spatial stratification of street vendors in downtown Mexico City  

E-Print Network (OSTI)

The fight for space between city administrators and street vendors working in city centers is one of the major controversies about street commerce. Trying to renew and upgrade their downtowns, city administrators of most ...

Baroni, Bruno Nazim

2007-01-01T23:59:59.000Z

59

Catalytic reforming process  

Science Conference Proceedings (OSTI)

This patent describes a catalytic reforming process which comprises contacting a naphtha range feed with a low acidity extrudate comprising an intermediate and/or a large pore acidic zeolite bound with a low acidity refractory oxide under reforming conditions to provide a reaction product of increased aromatic content, the extrudate having been prepared with at least an extrusion-facilitating amount of a low acidity refractory oxide in colloidal form and containing at least one metal species selected from the platinum group metals.

Absil, R.P.; Huss, A. Jr.; McHale, W.D.; Partridge, R.D.

1989-06-13T23:59:59.000Z

60

A Laboratory Model of Urban Street-Canyon Flows  

Science Conference Proceedings (OSTI)

A circulating water channel is constructed to examine urban street-canyon flow. In the cases of an even-notch street canyon in which model buildings on both sides of the street have equal heights, one vortex is observed in model canyons with ...

Jong-Jin Baik; Rae-Seol Park; Hye-Yeong Chun; Jae-Jin Kim

2000-09-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


61

Pecan Street Project Inc | Open Energy Information  

Open Energy Info (EERE)

Project Inc Project Inc Jump to: navigation, search Name Pecan Street Project Inc Place Austin, Texas Zip 78759 Product Austin-based smart grid, energy system developer. The Pecan Street Project is involved in a smart grid project. Coordinates 30.267605°, -97.742984° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":30.267605,"lon":-97.742984,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

62

LED Street and Area Lighting Technologies  

Science Conference Proceedings (OSTI)

Light emitting diodes (LEDs) are being used for applications beyond just indicator lights. One of those applications, street and area lighting, is of considerable interest. This interest is generated by potential reductions that can be achieved in operating costs resulting from lower maintenance costs as well as potentially lower electricity costs that result from the higher efficiency of LED lamps in the systems, the capability to dim and control LED systems, and better light quality. This white paper l...

2008-07-09T23:59:59.000Z

63

Multifuel reformer R D  

DOE Green Energy (OSTI)

The on-board fuel for fuel cell powered vehicles may be one or more of hydrogen, methanol, ethanol, natural gas, propane, or other liquified petroleum gases. To use hydrogen as the fuel, suitable means of storing, and subsequently delivering, adequate quantities of the gas must be developed. For all other fuels suitable reformers must be developed to convert the fuel to hydrogen or a hydrogen-rich gas mixture at rates corresponding to the varying power demand rates of the automotive system; this is especially true for the lower temperature fuel cells, such as the polymer electrolyte fuel cell which operates at 80{degrees}C and the phosphoric acid fuel cell which operates at 190{degrees}C. This paper discusses the key design and performance characteristics of such hydrogen storage and fuel reformer systems for use in stand-alone fuel cell automotive applications.

Kumar, R.; Ahmed, S.

1991-01-01T23:59:59.000Z

64

Methanol partial oxidation reformer  

DOE Patents (OSTI)

A partial oxidation reformer is described comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell. 7 figs.

Ahmed, S.; Kumar, R.; Krumpelt, M.

1999-08-24T23:59:59.000Z

65

Methanol partial oxidation reformer  

DOE Patents (OSTI)

A partial oxidation reformer is described comprising a longitudinally extending chamber having a methanol, water and an air inlet and an outlet. An igniter mechanism is near the inlets for igniting a mixture of methanol and air, while a partial oxidation catalyst in the chamber is spaced from the inlets and converts methanol and oxygen to carbon dioxide and hydrogen. Controlling the oxygen to methanol mole ratio provides continuous slightly exothermic partial oxidation reactions of methanol and air producing hydrogen gas. The liquid is preferably injected in droplets having diameters less than 100 micrometers. The reformer is useful in a propulsion system for a vehicle which supplies a hydrogen-containing gas to the negative electrode of a fuel cell. 7 figs.

Ahmed, S.; Kumar, R.; Krumpelt, M.

1999-08-17T23:59:59.000Z

66

Catalytic reforming catalyst  

Science Conference Proceedings (OSTI)

An improved catalyst, having a reduced fouling rate when used in a catalytic reforming process, said catalyst comprising platinum disposed on an alumina support wherein the alumina support is obtained by removing water from aluminum hydroxide produced as a by-product from a ziegler higher alcohol synthesis reaction, and wherein the alumina is calcined at a temperature of 1100-1400/sup 0/F so as to have a surface area of 165 to 215 square meters per gram.

Buss, W.C.; Kluksdahl, H.E.

1980-12-09T23:59:59.000Z

67

Southwestern Power Administration One West Third Street  

NLE Websites -- All DOE Office Websites (Extended Search)

Department of Energy Department of Energy Southwestern Power Administration One West Third Street Tulsa, Oklahoma 74103-3502 December 2, 2008 ENVIRONMENTAL POLICY STATEMENT The Environmental Policy is the driver for implementing and improving Southwestern Power Administration's (Southwestern) Environmental Management System so that Southwestern can maintain and improve environmental performance. The policy reflects the commitment of top management to comply with applicable legal and other requirements, to prevent pollution and to continually improve. Southwestern's Environmental Policy forms the basis upon which its Environmental Objectives and Targets are established. Southwestern's senior management has committed in writing the following Environmental Policy:

68

Steam reformer with catalytic combustor  

DOE Patents (OSTI)

A steam reformer is disclosed having an annular steam reforming catalyst bed formed by concentric cylinders and having a catalytic combustor located at the center of the innermost cylinder. Fuel is fed into the interior of the catalytic combustor and air is directed at the top of the combustor, creating a catalytic reaction which provides sufficient heat so as to maintain the catalytic reaction in the steam reforming catalyst bed. Alternatively, air is fed into the interior of the catalytic combustor and a fuel mixture is directed at the top. The catalytic combustor provides enhanced radiant and convective heat transfer to the reformer catalyst bed.

Voecks, Gerald E. (La Crescenta, CA)

1990-03-20T23:59:59.000Z

69

Information Resources: Webcast: Evaluating LED Street Lighting Solutions  

NLE Websites -- All DOE Office Websites (Extended Search)

Evaluating LED Street Lighting Solutions Evaluating LED Street Lighting Solutions In this July 20, 2010 webcast, Edward Smalley of Seattle City Light provided an update on DOE Municipal Solid-State Street Lighting Consortium activities. The webcast also presented perspectives from members who are involved with implementing LED street lighting evaluations, including Tod Rosinbum of the City of Portland, Oregon, John Walter of National Grid, and Amy Olay of the City of San Jose, California. View presentation slides (Visit the Adobe® Web site to Download Adobe Reader.) Introduction (PDF 984 KB) Edward Smalley, DOE Municipal Solid-State Street Lighting Consortium, Moderator Evaluating LED Street Lighting Solutions (PDF 404 KB) Tod Rosinbum, City of Portland, Oregon LED Pilot Projects: A Utility Perspective (PDF 112 KB)

70

Internal natural gas reformer-dividers for a solid oxide fuel cell generator configuration  

Science Conference Proceedings (OSTI)

This patent describes a fuel cell generator configuration. It comprises electrically connected, axially elongated, fuel cells, each cell having an outer and inner electrode with solid oxide electrolyte therebetween; where elongated dividers separate and are positioned between fuel cells, and where at least one of the elongated dividers is hollow, the hollow divider having solid elongated walls, a reformable fuel mixture entrance, and an exit allowing passage of reformed fuel to the fuel cells, and where the cross-section of the divider contains a catalytic reforming material.

Reichner, P.

1992-01-21T23:59:59.000Z

71

Electric, Street Railway, and Gas Corporations (South Dakota) | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Electric, Street Railway, and Gas Corporations (South Dakota) Electric, Street Railway, and Gas Corporations (South Dakota) Electric, Street Railway, and Gas Corporations (South Dakota) < Back Eligibility Commercial Developer Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State South Dakota Program Type Line Extension Analysis Provider South Dakota Public Utilities Commission This legislation contains provisions pertaining to a corporation formed for the purpose of constructing, maintaining and operating a street railway or railways; generating, transmitting or distributing electricity to be sold to or used by the public for heat, light or power manufacturing; or producing, supplying, or transporting natural or artificial gas. The

72

Quantity versus Quality in Off-Street Parking Requirements  

E-Print Network (OSTI)

off-street parking requirements does not restrict parking orrequirements if they are con- verted to residential uses. Los Angeles, for example, does

Mukhija, Vinit; Shoup, Donald

2006-01-01T23:59:59.000Z

73

Information Resources: Member Case Studies: LED Street Lighting...  

NLE Websites -- All DOE Office Websites (Extended Search)

Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) This May 8, 2013 webcast featured presentations from DOE Municipal Solid-State...

74

Federal Energy Management Program: Outdoor Solid State Street...  

NLE Websites -- All DOE Office Websites (Extended Search)

& Structures Case Studies Resources Working Group Distributed Energy ResourcesCombined Heat & Power Resources Renewable Energy Outdoor Solid State Street and Roadway Lighting...

75

Texas Avenue mixed-use urban street redevelopment, Lubbock, Texas.  

E-Print Network (OSTI)

??This thesis focused primarily on establishing design principles for mixed-use urban street redevelopment. This study began with a literature review exploring the history of modern… (more)

[No author

76

Novel Reforming Catalysts  

Science Conference Proceedings (OSTI)

Aqueous phase reforming is useful for processing oxygenated hydrocarbons to hydrogen and other more useful products. Current processing is hampered by the fact that oxide based catalysts are not stable under high temperature hydrothermal conditions. Silica in the form of structured MCM-41 is thermally a more stable support for Co and Ni than conventional high surface area amorphous silica but hydrothermal stability is not demonstrated. Carbon nanotube supports, in contrast, are highly stable under hydrothermal reaction conditions. In this project we show that carbon nanotubes are stable high activity/selectivity supports for the conversion of ethylene glycol to hydrogen.

Pfefferle, Lisa D; Haller, Gary L

2012-10-16T23:59:59.000Z

77

NEPA Contracting Reform Guidance  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

defining early what contractors should accomplish < establishing contracts ahead of time < minimizing cost while maintaining quality by * maximizing competition and use of incentives * using past performance information in awarding work * managing the NEPA process as a project This guidance provides: < model statements of work < information on contract types and incentives < direction on effective NEPA contract management by the NEPA Document Manager < a system for measuring NEPA process costs < NEPA contractor evaluation procedures < details on the DOE NEPA Web site U.S. Department of Energy, Office of NEPA Policy and Assistance, December 1996 NEPA CONTRACTING REFORM GUIDANCE Table of Contents 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

78

Multizone catalytic reforming process  

Science Conference Proceedings (OSTI)

This patent describes a process for the catalytic reforming of hydrocarbons comprising contacting the hydrocarbon feed in two sequential catalyst zones. It comprises: a first catalyst zone contains a first catalytic composite consisting essentially of a platinum component, a germanium component, a refractory inorganic oxide, and a halogen component; and a second catalyst zone contains a second catalytic composite comprising a platinum component, a germanium component, a refractory inorganic oxide, a halogen component, and catalytically effective amounts of a metal promoter selected from rhenium, rhodium, ruthenium, cobalt, nickel, and iridium, and mixtures thereof.

Moser, M.C.; Lawson, R.J.; Antos, G.J.; Wang, L.; Parulekar, V.N.

1990-05-29T23:59:59.000Z

79

Patent Counsel - Patent Reform | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Patent Counsel - Patent Reform Patent Counsel - Patent Reform America invents Act 20112.pdf More Documents & Publications PETITION FOR ADVANCE WAIVER OF PATENT RIGHTS Office of...

80

Attrition resistant fluidizable reforming catalyst - Energy ...  

A method of preparing a steam reforming catalyst characterized by improved resistance to attrition loss when used for cracking, reforming, water gas shift and ...

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


81

Catalytic reforming optimization  

Science Conference Proceedings (OSTI)

The authors have previously examined correlations between catalytic reforming parameters for an L-35-6 unit at the Gor'knefteorgsintez Industrial Association. Experimental design was used to derive polynomial equations describing the correlations for each reactor. Further research on optimizing the reforming has been based on these results. They adopted the following strategy to define the best working parameters: they define a temperature that would provide the maximum target-product yield while maintaining a given working life. Most of the aromatic hydrocarbons are formed by the naphthene dehydrogenation, which is endothermic, so the greater the temperature drop over the height, the more rapid the process. The temperature difference thus indicates the current catalyst activity. To increase the target-product yield, one must raise the inlet temperature and ensure the largest drop across the catalyst. They examined an algorithm with fixed inlet conditions as regards flow rate and raw material composition. This algorithm provides the basis of software for the automatic control of the L-35-6 reactor unit at the Gor'knefteorgsintez Industrial Association. The system has been checked out and put into experimental operation.

Mazina, S.G.; Rybtsov, V.V.; Priss-Titarenko, T.A.

1988-11-10T23:59:59.000Z

82

Notices 888 First Street, NE., Washington, DC  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

11 Federal Register 11 Federal Register / Vol. 76, No. 122 / Friday, June 24, 2011 / Notices 888 First Street, NE., Washington, DC 20426. The filings in the above-referenced proceeding are accessible in the Commission's eLibrary system by clicking on the appropriate link in the above list. They are also available for review in the Commission's Public Reference Room in Washington, DC. There is an eSubscription link on the Web site that enables subscribers to receive e-mail notification when a document is added to a subscribed docket(s). For assistance with any FERC Online service, please e-mail FERCOnlineSupport@ferc.gov or call (866) 208-3676 (toll free). For TTY, call (202) 502-8659. Dated: June 20, 2011. Kimberly D. Bose, Secretary. [FR Doc. 2011-15859 Filed 6-23-11; 8:45 am]

83

Notices 888 First Street NE., Washington, DC  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

53 Federal Register 53 Federal Register / Vol. 78, No. 56 / Friday, March 22, 2013 / Notices 888 First Street NE., Washington, DC 20426. This filing is accessible on-line at http://www.ferc.gov, using the ''eLibrary'' link and is available for review in the Commission's Public Reference Room in Washington, DC. There is an ''eSubscription'' link on the Web site that enables subscribers to receive email notification when a document is added to a subscribed docket(s). For assistance with any FERC Online service, please email FERCOnlineSupport@ferc.gov, or call (866) 208-3676 (toll free). For TTY, call (202) 502-8659. Comment Date: 5:00 p.m. Eastern Time on April 2, 2013. Dated: March 15, 2013. Kimberly D. Bose, Secretary. [FR Doc. 2013-06602 Filed 3-21-13; 8:45 am] BILLING CODE 6717-01-P

84

Notices Disabled, 1401 S. Clark Street, Suite  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

13 Federal Register 13 Federal Register / Vol. 78, No. 240 / Friday, December 13, 2013 / Notices Disabled, 1401 S. Clark Street, Suite 10800, Arlington, Virginia 22202-4149. FOR FURTHER INFORMATION CONTACT: Barry S. Lineback, Telephone: (703) 603-7740, Fax: (703) 603-0655, or email CMTEFedReg@AbilityOne.gov. SUPPLEMENTARY INFORMATION: Addition On 6/28/2013 (78 FR 38952-38953), the Committee for Purchase From People Who Are Blind or Severely Disabled published notice of proposed addition to the Procurement List. After consideration of the material presented to it concerning capability of qualified nonprofit agency to provide the service and impact of the addition on the current or most recent contractors, the Committee has determined that the service listed below is suitable for procurement by the

85

Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop  

NLE Websites -- All DOE Office Websites (Extended Search)

Los Angeles, CA to someone Los Angeles, CA to someone by E-mail Share Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Facebook Tweet about Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Twitter Bookmark Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Google Bookmark Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Delicious Rank Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Los Angeles, CA on Digg Find More places to share Solid-State Lighting: Municipal Consortium

86

FirstEnergy (Potomac Edison) - Municipal and Street Lighting Program  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FirstEnergy (Potomac Edison) - Municipal and Street Lighting FirstEnergy (Potomac Edison) - Municipal and Street Lighting Program (Maryland) FirstEnergy (Potomac Edison) - Municipal and Street Lighting Program (Maryland) < Back Eligibility Commercial Industrial Institutional Local Government Nonprofit Schools State Government Savings Category Appliances & Electronics Commercial Lighting Lighting Program Info State Maryland Program Type Utility Rebate Program Rebate Amount '''Street Lighting'''br/> High Pressure Sodium Fixtures: $10 - $50/unit LED/Induction Fixtures: $50 '''Traffic/Pedestrian Signals''' Lamp/Signal/Arrows: $35/unit Provider FirstEnergy (Potomac Edison) FirstEnergy offers several incentives for non-residential and municipal customers to upgrade traffic signals, pedestrian signals, street lights to more efficient fixtures. The Municipal Lighting Incentive Program offers

87

High severity catalytic reforming process  

Science Conference Proceedings (OSTI)

A high-severity catalytic reforming process is described comprising: (a) passing a mixture comprising a catalytic reforming feed stream and a recycle stream into a catalytic reforming reaction zone which is maintained at high-severity reforming conditions; (b) cooling an effluent stream comprising hydrogen and hydrocarbonaceous catalytic reforming reaction products which is withdrawn from the reaction zone; (c) passing the cooled effluent stream into a vapor-liquid separation zone and recovering therefrom a liquid stream comprising hydrocarbons and a hydrogen-rich gas stream; (d) passing the hydrogen-rich gas stream through an adsorption zone wherein the gas is contacted with a treating material which removes polycyclic aromatic compounds from the gas stream, the compounds remaining in the adsorption zone; (e) mixing a portion of the hydrogen-rich gas stream, which is the recycle stream, with the feed stream to form the charge stock mixture and withdrawing the balance of the hydrogen-rich gas stream, which is denoted as net hydrogen, from the catalytic reforming area, all of the hydrogen-rich gas stream being substantially free of polycyclic aromatic compounds; and (f) fractionating the liquid stream and recovering an overhead product comprising light hydrocarbons and a bottoms product comprising reformate.

Bennett, R.W.; Cottrell, P.R.; Gilsdorf, N.L.; Winfield, M.D.

1988-03-22T23:59:59.000Z

88

Liquid fuel reformer development.  

DOE Green Energy (OSTI)

At Argonne National Laboratory we are developing a process to convert hydrocarbon fuels to a clean hydrogen feed for a fuel cell. The process incorporates a partial oxidation/steam reforming catalyst that can process hydrocarbon feeds at lower temperatures than existing commercial catalysts. We have tested the catalyst with three diesel-type fuels: hexadecane, low-sulfur diesel fuel, and a regular diesel fuel. We achieved complete conversion of the feed to products. Hexadecane yielded products containing 60% hydrogen on a dry, nitrogen-free basis at 800 C. For the two diesel fuels, higher temperatures, >850 C, were required to approach similar levels of hydrogen in the product stream. At 800 C, hydrogen yield of the low sulfur diesel was 32%, while that of the regular diesel was 52%. Residual products in both cases included CO, CO{sub 2}, ethane, ethylene, and methane.

Ahmed, S.; Krumpelt, M.; Pereira, C.; Wilkenhoener, R.

1999-07-30T23:59:59.000Z

89

Multizone catalytic reforming process  

Science Conference Proceedings (OSTI)

This patent describes a process for the catalytic reforming of hydrocarbons comprising contacting the hydrocarbon feed in two sequential catalyst zones. It comprises: an initial catalyst zone which is a fixed-bed system and contains an initial catalytic composite comprising a platinum component, a germanium component, a refractory inorganic oxide, and a halogen component; and a terminal catalyst zone which is a moving-bed system with associated continuous catalyst regeneration and contains a terminal catalytic composite having the essential absence of germanium and comprising a platinum component, a refractory inorganic oxide, a halogen component, and catalytically effective amounts of a metal promoter selected from one or more of the rhenium, tin, indium, rhodium, ruthenium, cobalt, nickel, and iridium.

Moser, M.; Lawson, R.J.; Wang, L.; Parulekar, V.; Peer, R.L.; Hamlin, C.R.

1991-01-15T23:59:59.000Z

90

Puerto Rico Refinery Catalytic Reforming Downstream Charge ...  

U.S. Energy Information Administration (EIA)

Puerto Rico Refinery Catalytic Reforming Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

91

Mississippi Refinery Catalytic Reforming Downstream Charge ...  

U.S. Energy Information Administration (EIA)

Mississippi Refinery Catalytic Reforming Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

92

Louisiana Refinery Catalytic Reforming Downstream Charge Capacity ...  

U.S. Energy Information Administration (EIA)

Louisiana Refinery Catalytic Reforming Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

93

Hiring Reform | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hiring Reform Hiring Reform Hiring Reform President Obama's Memorandum dated May 11, 2010, Improving the Federal Recruitment and Hiring Process, is Phase I of the Administration's comprehensive initiative to address major, long-standing impediments to recruiting and hiring the best and the brightest into the Federal civilian workforce. The Memorandum is based on issues that DOE and others brought to the attention of OPM, and it is designed to help Agencies build the workforce you need to achieve your goals. The Presidential Memorandum launches the Obama Administration's flagship personnel policy reform initiative. It builds on a nearly year-long collaboration between OPM and Agencies aimed at streamlining the hiring process and recruiting top talent, especially for mission-critical jobs.

94

Applications of solar reforming technology  

DOE Green Energy (OSTI)

Research in recent years has demonstrated the efficient use of solar thermal energy for driving endothermic chemical reforming reactions in which hydrocarbons are reacted to form synthesis gas (syngas). Closed-loop reforming/methanation systems can be used for storage and transport of process heat and for short-term storage for peaking power generation. Open-loop systems can be used for direct fuel production; for production of syngas feedstock for further processing to specialty chemicals and plastics and bulk ammonia, hydrogen, and liquid fuels; and directly for industrial processes such as iron ore reduction. In addition, reforming of organic chemical wastes and hazardous materials can be accomplished using the high-efficiency destruction capabilities of steam reforming. To help identify the most promising areas for future development of this technology, we discuss in this paper the economics and market potential of these applications.

Spiewak, I. [Weizmann Inst. of Science, Rehovoth (Israel); Tyner, C.E. [Sandia National Labs., Albuquerque, NM (United States); Langnickel, U. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Koeln (Germany)

1993-11-01T23:59:59.000Z

95

One West Third Street Tulsa, Oklahoma  

NLE Websites -- All DOE Office Websites (Extended Search)

Third Street Tulsa, Oklahoma 74103-3502 918-595-6600 Fax 918-595-6656 www.swpa.gov The UPDATE is published by and for customers, retirees, and employees of Southwestern Power Administration like: Katherine (K.C.) Thomas Director, Division of Information Technology (CIO) Tulsa, Oklahoma Special thanks to: Ron Beck Miya Boyken Ashley Butler Scott Carpenter Mike Deihl Ruben Garcia William Hiller David Kannady Jim McDonald Beth Nielsen Fritha Ohlson Tracey Stewart U P D AT E S O U T H W E S T E R N P O W E R A D M I N I S T R A T I O N J A N U A R Y - J U N E 2 0 0 7 Southwestern Responds to Reliability Requirements Southwestern expects to complete its agency-wide assessment regarding compliance with mandatory reliability standards under Standards Order 693 of the Federal Energy Regulatory Commission (FERC) by the June 18, 2007,

96

Lighting the Night: Technology, Urban Life and the Evolution of Street Lighting [Light in Place  

E-Print Network (OSTI)

Electrical 16. "Highway Lighting by So­ dium Vapor Lamps,"Possibilities of Street: Lighting Improve­ ments," TheLaunches Broad Street Lighting Promotion Campaign," The

Holden, Alfred

1992-01-01T23:59:59.000Z

97

Partial oxidation reforming of methanol  

DOE Green Energy (OSTI)

Methanol is an attractive fuel for fuel cell-powered vehicles because it has a fairly high energy density, can be pumped into the tank of a vehicle mush like gasoline, and is relatively easy to reform. For on-board reforming, the reformer must be compact and lightweight, and have rapid start-up and good dynamic response. Steam reforming reactors with the tube-and-shell geometry that was used on the prototype fuel cell-powered buses are heat transfer limited. To reach their normal operating temperature, these types of reactors need 45 minutes from ambient temperature start-up. The dynamic response is poor due to temperature control problems. To overcome the limitations of steam reforming, ANL explored the partial oxidation concept used in the petroleum industry to process crude oils. In contrast to the endothermic steam reforming reaction, partial oxidations is exothermic. Fuel and air are passed together over a catalyst or reacted thermally, yielding a hydrogen-rich gas. Since the operating temperature of such a reactor can be controlled by the oxygen-to- methanol ratio, the rates of reaction are not heat transfer limited. Start-up and transient response should be rapid, and the mass and volume are expected to be small by comparison.

Krumpelt, M.; Ahmed, S.; Kumar, R.

1996-04-01T23:59:59.000Z

98

Before House Committee on Oversight and Government Reform | Department...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

House Committee on Oversight and Government Reform Before House Committee on Oversight and Government Reform Before House Committee on Oversight and Government Reform By: Secretary...

99

Before the House Committee on Oversight and Government Reform...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oversight and Government Reform Before the House Committee on Oversight and Government Reform Before the Committee on Oversight and Government Reform, U.S. House of Representatives...

100

Information Resources: Webcast: Municipal Solid-State Street Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool This April 3, 2012 webcast presented information about the Retrofit Financial Analysis Tool developed by DOE"s Municipal Solid-State Street Lighting Consortium. Doug Elliott of Pacific Northwest National Laboratory provided a guided walk-through of what the tool can do and how to use it to evaluate costs and benefits associated with converting to LED street and roadway lighting. The webcast showed how city and other government agencies, utilities, finance and budget offices, and energy efficiency organizations can use the tool to compute annualized energy-cost savings, maintenance savings, greenhouse gas reductions, net present value, and simple payback, which can be helpful when putting together construction and conservation grant applications, as well as for preparing budgets and comparing incumbent costs to new costs.

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


101

Hope Street Academy Wind Project | Open Energy Information  

Open Energy Info (EERE)

Street Academy Wind Project Street Academy Wind Project Jump to: navigation, search Name Hope Street Academy Wind Project Facility Hope Street Academy Sector Wind energy Facility Type Community Wind Location KS Coordinates 39.031624°, -95.733482° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":39.031624,"lon":-95.733482,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

102

Gas, Heat, Water, Sewerage Collection and Disposal, and Street Railway  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Gas, Heat, Water, Sewerage Collection and Disposal, and Street Gas, Heat, Water, Sewerage Collection and Disposal, and Street Railway Companies (South Carolina) Gas, Heat, Water, Sewerage Collection and Disposal, and Street Railway Companies (South Carolina) < Back Eligibility Agricultural Commercial Construction Industrial Installer/Contractor Investor-Owned Utility Municipal/Public Utility Rural Electric Cooperative Utility Program Info State South Carolina Program Type Generating Facility Rate-Making Siting and Permitting Provider South Carolina Public Service Commission This legislation applies to public utilities and entities furnishing natural gas, heat, water, sewerage, and street railway services to the public. The legislation addresses rates and services, exemptions, investigations, and records. Article 4 (58-5-400 et seq.) of this

103

Information Resources: Municipal Solid-State Street Lighting...  

NLE Websites -- All DOE Office Websites (Extended Search)

6, 2010 webcast served as the first official meeting of the new DOE Municipal Solid-State Street Lighting Consortium. Ed Smalley of Seattle City Light and Bruce Kinzey of Pacific...

104

Flow Variability in a North American Downtown Street Canyon  

Science Conference Proceedings (OSTI)

Previous field and laboratory studies have indicated that flow and turbulence inside urban areas and, in particular, in street canyons, is very complex and is associated with wakes and vortices developing near buildings. However, a number of open ...

Petra Klein; James V. Clark

2007-06-01T23:59:59.000Z

105

Street and Parking Facility Lighting Retrofit Financial Analysis Tool Webinar  

Energy.gov (U.S. Department of Energy (DOE))

DOE will present a live webinar titled "Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool" on Thursday, August 22, from 1:00 p.m. to 2:00 p.m. Eastern Daylight Time....

106

Solid-State Lighting: Municipal Consortium LED Street Lighting...  

NLE Websites -- All DOE Office Websites (Extended Search)

Boston, MA to someone by E-mail Share Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Boston, MA on Facebook Tweet about...

107

Solid-State Lighting: Municipal Consortium LED Street Lighting...  

NLE Websites -- All DOE Office Websites (Extended Search)

Dallas, TX to someone by E-mail Share Solid-State Lighting: Municipal Consortium LED Street Lighting Workshop Presentations and Materials-Dallas, TX on Facebook Tweet about...

108

Benchmarking the Mean Streets of NYC and Beyond  

NLE Websites -- All DOE Office Websites (Extended Search)

Benchmarking the Mean Streets of NYC and Beyond Speaker(s): Conor Laver Date: September 30, 2013 - 12:00pm - 1:00pm Location: 90-3122 Seminar HostPoint of Contact: Louis-Benoit...

109

Street media : ambient messages in an urban space  

E-Print Network (OSTI)

Ambient street media are the media of our everyday lives in cities. Manifested in bits and fragments on the surfaces of the streetscape, these media often escape our notice - tuned out as visual clutter or dismissed as ...

Murthy, Rekha (Rekha S.)

2005-01-01T23:59:59.000Z

110

Information Resources: Using the Street and Parking Facility Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool This August 22, 2013 webinar provided a guided walk-through of the Street and Parking Facility Lighting Retrofit Financial Analysis Tool. Developed by a partnership of the DOE Municipal Solid-State Street Lighting Consortium, the Clinton Climate Initiative/C40, and the DOE Federal Energy Management Program, the Excel-based tool assists with the financial analysis of retrofitting street and parking facility lighting with more efficient alternatives. During the webinar, Doug Elliott of Pacific Northwest National Laboratory discussed how the tool can be used to evaluate costs and benefits associated with converting to more efficient street and parking facility lighting and how property owners, city and other government agencies, utilities, and energy efficiency organizations can use the tool to compute annualized energy and energy-cost savings, maintenance savings, greenhouse gas reductions, net present value, and simple payback associated with potential lighting upgrades.

111

Before the House Oversight and Government Reform Subcommittee...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Information Policy, Intergovernmental Relations, and Procurement Reform Before the House Oversight and Government Reform Subcommittee on Technology, Information Policy,...

112

Safety and Security Directives Reform  

NLE Websites -- All DOE Office Websites (Extended Search)

Reforming a "Mountain" of Policy Reforming a "Mountain" of Policy Beginning with his confirmation hearings in January 2009, Energy Secretary Steven Chu challenged the Department of Energy to take a fresh look at how we conduct business. This challenge provided the opportunity for DOE to put in place the most effective and efficient strategies to accomplish the Department's missions safely and securely. In response to the Secretary's challenge and building on the results of Deputy Secretary Poneman's Safety and Security Reform studies, the Office of Health, Safety and Security (HSS) broadened its directives review activities during 2009. By November 2009 HSS had initiated a disciplined review of all health, safety, and security directives, which included a systematic review of the Department's safety and security regulatory model.

113

Evaluate reformer performance at a glance  

Science Conference Proceedings (OSTI)

Catalytic reforming is becoming increasingly important in replacing octane lost as the removal of lead from worldwide gasoline pools continues. A method has been developed that can quickly evaluate the performance of any catalytic reformer. The catalytic naphtha reforming process primarily involves three well-known reactions. These are aromatization of naphthenes, cyclization of paraffins and hydrocracking of paraffins. Hydrogen is produced in the process of aromatization and dehydrocyclization of paraffins. Reformer performance is normally evaluated with a reformate analysis (PONA) and yield of C{sub 5{sup +}} reformate. This method of quick evaluation of reformer performance is based upon the main assumption that the increase in hydrocarbon moles in the process is equal to the number of C{single_bond}C bond ruptures and one mole of hydrogen is absorbed to saturate the same. This new method calculates aromatization efficiency, paraffin conversion, aromatic selectivity and finally the paraffin, naphthene and aromatic content of C{sub 5{sup +}} reformate.

Nag, A. [Indian Oil Corporation Ltd., Gujarat (India)

1996-02-01T23:59:59.000Z

114

Bringing electricity reform to the Philippines  

SciTech Connect

Electricity reforms will not translate to competition overnight. But reforms are inching their way forward in institutions and stakeholders of the Philippine electricity industry, through regulatory and competition frameworks, processes, and systems promulgated and implemented. (author)

Fe Villamejor-Mendoza, Maria

2008-12-15T23:59:59.000Z

115

Fluidized Bed Steam Reforming Technology Overview  

Coal added as reductant and for energy • What happens inside the reformer? Water evaporates Nitrates reduced to nitrogen gas

116

Method of steam reforming methanol to hydrogen  

DOE Patents (OSTI)

The production of hydrogen by the catalyzed steam reforming of methanol is accomplished using a reformer of greatly reduced size and cost wherein a mixture of water and methanol is superheated to the gaseous state at temperatures of about 800.degree. to about 1,100.degree. F. and then fed to a reformer in direct contact with the catalyst bed contained therein, whereby the heat for the endothermic steam reforming reaction is derived directly from the superheated steam/methanol mixture.

Beshty, Bahjat S. (Lower Makefield, PA)

1990-01-01T23:59:59.000Z

117

Olefins from High Yield Autothermal Reforming Process ...  

Isobutylene is used to produce fuel additives. The autothermal reforming process can produce isobutylene and requires no external energy input ...

118

Accelerated Weathering of Fluidized Bed Steam Reformation ...  

Science Conference Proceedings (OSTI)

Sep 16, 2007 ... Accelerated Weathering of Fluidized Bed Steam Reformation Material Under Hydraulically Unsaturated Conditions by E.M. Pierce ...

119

Continuing Management Reform | National Nuclear Security Administratio...  

National Nuclear Security Administration (NNSA)

Continuing Management Reform | National Nuclear Security Administration Our Mission Managing the Stockpile Preventing Proliferation Powering the Nuclear Navy Emergency Response...

120

Attrition resistant fluidizable reforming catalyst  

DOE Patents (OSTI)

A method of preparing a steam reforming catalyst characterized by improved resistance to attrition loss when used for cracking, reforming, water gas shift and gasification reactions on feedstock in a fluidized bed reactor, comprising: fabricating the ceramic support particle, coating a ceramic support by adding an aqueous solution of a precursor salt of a metal selected from the group consisting of Ni, Pt, Pd, Ru, Rh, Cr, Co, Mn, Mg, K, La and Fe and mixtures thereof to the ceramic support and calcining the coated ceramic in air to convert the metal salts to metal oxides.

Parent, Yves O. (Golden, CO); Magrini, Kim (Golden, CO); Landin, Steven M. (Conifer, CO); Ritland, Marcus A. (Palm Beach Shores, FL)

2011-03-29T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


121

Charting a Course to Autonomy: Bureaucratic Politics and the Transformation of Wall Street  

E-Print Network (OSTI)

2001 . . . . . . . . . . 179 vii Glossary American Bankersiii Contents List of Figures vi Glossary viii Acronyms xi 178, 80, 83, 127, 128, Glossary: Association of Bank Holding

Ryan, Peter Joseph

2013-01-01T23:59:59.000Z

122

The tobacco industry's use of Wall Street analysts in shaping policy  

E-Print Network (OSTI)

prices would bankrupt industry. Washington Times, 27 AprilSettlement with the Tobacco Industry: National AssociationScience for hire: a tobacco industry strategy to influence

Alamar, B C; Glantz, Stanton A. Ph.D.

2004-01-01T23:59:59.000Z

123

Wall Street Journal / MIT Sloan How to Back the Right Technology  

E-Print Network (OSTI)

-ray tube, or CRT; liquid-crystal display, or LCD; organic light- emitting diode, or OLED; and plasma. Each

Southern California, University of

124

Charting a Course to Autonomy: Bureaucratic Politics and the Transformation of Wall Street  

E-Print Network (OSTI)

Technical Report 446-B, Office of Inspector General, U.S.when it was enacted (Office of Inspector General, 2008, 1-Press, 1928. of Inspector General, U.S. SEC Office, “SEC’s

Ryan, Peter Joseph

2013-01-01T23:59:59.000Z

125

INTEGRAL CATALYTIC COMBUSTION/FUEL REFORMING  

E-Print Network (OSTI)

INTEGRAL CATALYTIC COMBUSTION/FUEL REFORMING FOR GAS TURBINE Prepared For: California Energy REPORT (FAR) INTEGRAL CATALYTIC COMBUSTION/FUEL REFORMING FOR GAS TURBINE CYCLES EISG AWARDEE University://www.energy.ca.gov/research/index.html. #12;Page 1 Integral Catalytic Combustion/Fuel Reforming for Gas Turbine Cycles EISG Grant # 99

126

One West Third Street Tulsa, Oklahoma  

NLE Websites -- All DOE Office Websites (Extended Search)

Jimmy Hardin Jimmy Hardin Working Foreman Jonesboro Maintenance Unit Special thanks to: SWPA Marshall Boyken Kenny Broadaway Scott Carpenter Dallas Cooper Jerry Ferguson Janet Hagar Danny Johnson Darlene Low Jim McDonald Jerry Murr Beth Nielsen Carrie Quick Aiden Smith Steve Wall Jon Worthington WNT Ashley Butler Vicki Clarke Ruben Garcia Brad Howland William Hiller Kathy O'Neal Elaine Webb U P DAT E S O U T H W E S T E R N P O W E R A D M I N I S T R A T I O N J u l y - S e p t e m b e r 2 0 0 8 Southwestern "Zero Heroes" Stay Safe Sometimes being a "zero hero" is the best way to be. This was certainly the case for Southwestern in Fiscal Year (FY) 2008, when the agency achieved a Recordable Accident Frequency Rate (RAFR) of 0.0, which equates to not a single recordable injury for every

127

One West Third Street Tulsa, Oklahoma  

NLE Websites -- All DOE Office Websites (Extended Search)

Jane Thomas Jane Thomas Supply Technician Tulsa, Oklahoma Special thanks to: SWPA Marshall Boyken Kenny Broadaway Mike Dawson Scott Holland Beth Nielsen Margaret Skidmore Randy Staponski Gary Swartzlander Ron Szatmary Steve Wall Jon Worthington CNI/Bearskin Ashley Butler Vicki Clarke Ruben Garcia William Hiller Kathy O'Neal KC District Corps George Boban Andre Vasseur Tulsa District Corps Dan Brueggenjohann Little Rock District Corps Lee Beverly U P DAT E S O U T H W E S T E R N P O W E R A D M I N I S T R A T I O N J U LY - D E C E M B E R 2 0 1 0 continued on page 7 The Stockton Powerplant in Missouri is back online after an extended outage caused when a blade section sheared off of the project's only turbine in February 2009. The nearly five-ton section of blade was reattached in early August 2010 after related repairs had been

128

One West Third Street Tulsa, Oklahoma  

NLE Websites -- All DOE Office Websites (Extended Search)

David Reynolds David Reynolds Electronics Technician Gore, Oklahoma Special thanks to: SWPA Marshall Boyken Beth Nielsen Carrie Quick Dawn Rodriguez Steve Wall CNI/Bearskin Vicki Clarke Ruben Garcia William Hiller Chad Holland Kathy O'Neal Jimmy Robison Mary Beth Hudson Tulsa District Corps Rhonda James SW Division Corps P.J. Spaul Little Rock District Corps U P DAT E S O U T H W E S T E R N P O W E R A D M I N I S T R A T I O N A P R I L - J U N E 2 0 1 0 Southwestern Readies for Remote Chance continued on page 2 During a hypothetical spring in the near future, a virulent new strain of flu overwhelms medical services across the country. The contagion spreads quickly and easily in offices, schools, and public places, and an effective vaccine is months away. As the infection reaches pandemic proportions, Southwestern employees are instructed

129

Unfunded Mandates Reform Act; Intergovernmental Consultation | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Unfunded Mandates Reform Act; Intergovernmental Consultation Unfunded Mandates Reform Act; Intergovernmental Consultation Unfunded Mandates Reform Act; Intergovernmental Consultation The Department of Energy (DOE) today publishes a final statement of policy on intergovernmental consultation under the Unfunded Mandates Reform Act of 1995. The policy reflects the guidelines and instructions that the Director of the Office of Management and Budget (OMB) provided to each agency to develop, with input from State, local, and tribal officials, an intergovernmental consultation process with regard to significant intergovernmental mandates contained in a notice of proposed rulemaking. Unfunded Mandates Reform Act; Intergovernmental Consultation More Documents & Publications TEC Working Group Topic Groups Tribal Key Documents

130

NEPA Contracting Reform Guidance | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Contracting Reform Guidance Contracting Reform Guidance NEPA Contracting Reform Guidance This documents provides guidance on NEPA contracting strategy, including: defining the work of the contractor; establishing contracts ahead of time; minimizing cost while maintaining quality. Guidance also provides: model statements of work, direction on NEPA contract management by NEPA Document Manager; a system for measuring NEPA costs and for evaluating contractor procedures; details on the DOE NEPA website. NEPA Contracting Reform Guidance More Documents & Publications NEPA Contracting Reform Guidance (December 1996) Statement of Work-National Environmental Policy Act (NEPA) Support Services Acquisition: Preparation and Review of Environmental Impact Statements, Environmental Assessments, Environmental Reports, and other Environmental

131

Unfunded Mandates Reform Act; Intergovernmental Consultation | Department  

NLE Websites -- All DOE Office Websites (Extended Search)

Unfunded Mandates Reform Act; Intergovernmental Consultation Unfunded Mandates Reform Act; Intergovernmental Consultation Unfunded Mandates Reform Act; Intergovernmental Consultation The Department of Energy (DOE) today publishes a final statement of policy on intergovernmental consultation under the Unfunded Mandates Reform Act of 1995. The policy reflects the guidelines and instructions that the Director of the Office of Management and Budget (OMB) provided to each agency to develop, with input from State, local, and tribal officials, an intergovernmental consultation process with regard to significant intergovernmental mandates contained in a notice of proposed rulemaking. Unfunded Mandates Reform Act; Intergovernmental Consultation More Documents & Publications TEC Working Group Topic Groups Tribal Key Documents

132

New Rules Help Pocahontas Brighten Streets | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Rules Help Pocahontas Brighten Streets Rules Help Pocahontas Brighten Streets New Rules Help Pocahontas Brighten Streets October 21, 2010 - 10:00am Addthis The City of Pocahontas, Iowa swill replace sodium streetlights with LED fixtures. | File photo The City of Pocahontas, Iowa swill replace sodium streetlights with LED fixtures. | File photo Maya Payne Smart Former Writer for Energy Empowers, EERE What are the key facts? Pocahontas, Iowa was awarded a Recovery Act grant of more than $81,000. The city will replace 266 high-pressure sodium streetlights with LED fixtures. The LED lights are projected to reduce energy and maintenance costs by more than $17, 000 a year. Officials of the City of Pocahontas, Iowa, thought replacing old streetlights with light-emitting diode (LED) lighting was a no-brainer.

133

Easy Street (Smart Grid Project) | Open Energy Information  

Open Energy Info (EERE)

Easy Street (Smart Grid Project) Easy Street (Smart Grid Project) Jump to: navigation, search Project Name Easy Street Country Netherlands Headquarters Location Breda, Netherlands Coordinates 51.574806°, 4.774816° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":51.574806,"lon":4.774816,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

134

Microsoft PowerPoint - Pecan Street-Scott Hinson-Building America.pptx  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Pecan Street Inc. Pecan Street Inc. Scott Hinson shinson@pecanstreet.org Contents Pecan Street Background Pecan Street Research Initiatives Pike Powers Commercialization Laboratory Light Bulbs Pecan Street Background Information What is Pecan Street Who is Pecan Street Research Objectives and Initiatives Residential Home Energy Data Deepest residential energy available Enables research and application development not possible with "normal" data Granularity Comparison August 10, 2011: 60-minute Consumption Data (kW) August 10, 2011: 1-hour Consumption Data (kW) 0 4 8 12 04:00 08:00 12:00 16:00 20:00 Pecan Street Consortium Granularity Comparison August 10, 2011: 15-minute Consumption Data (kW 0 4 8 12 04:00 08:00 12:00 16:00 20:00 Pecan Street Consortium Granularity Comparison

135

A Review of Street Lighting Evaluations: Crime Reduction Effects  

E-Print Network (OSTI)

Abstract: Consideration of the literature concerning street lighting effects on crime yields the following conclusions: (1) Precisely targeted increases in street lighting generally have crime reduction effects. (2) More general increases in street lighting seem to have crime prevention effects, but this outcome is not universal Older and U.S. research yield fewer positive results than more recent U.K. research. (3) Even untargeted increases in crime prevention generally make residents less fearful of crime or more confident of their own safety at night. (4) In the most recent and sophisticated studies, street lighting improvements are associated with crime reductions in the daytime as well as during the hours of darkness. (5) The debate about lighting effects has served to preclude a more refined analysis of the means by and circumstances in which lighting might reduce crime. Our aim should now be to use context-appropriate lighting schemes as part of a full repertoire of crime reduction tactics. Recommendations based upon a strategic view of current crime reduction policy are made about how lighting effects could be clarified and elaborated. The provisions of the British Crime and Disorder Act 1998 constitute a potential vehicle for lighting programmes operating within crime reduction schemes generally.

Ken Pease

1999-01-01T23:59:59.000Z

136

Mr. Tad W. Patzek 13331 Trail Drive Street  

E-Print Network (OSTI)

Mr. Tad W. Patzek 13331 Trail Drive Street Austin, Texas 78737 Dear Mr. Patzek: THE SECRETARY OF THE INTERIOR WASHINGTON MAR 11 2011 It is my pleasure to appoint you as a member of the Ocean Energy Safety of the Bureau of Ocean Energy Management, Regulation and Enforcement on matters and actions relating to offshore

Patzek, Tadeusz W.

137

Plasma-catalyzed fuel reformer  

DOE Patents (OSTI)

A reformer is disclosed that includes a plasma zone to receive a pre-heated mixture of reactants and ionize the reactants by applying an electrical potential thereto. A first thermally conductive surface surrounds the plasma zone and is configured to transfer heat from an external heat source into the plasma zone. The reformer further includes a reaction zone to chemically transform the ionized reactants into synthesis gas comprising hydrogen and carbon monoxide. A second thermally conductive surface surrounds the reaction zone and is configured to transfer heat from the external heat source into the reaction zone. The first thermally conductive surface and second thermally conductive surface are both directly exposed to the external heat source. A corresponding method and system are also disclosed and claimed herein.

Hartvigsen, Joseph J.; Elangovan, S.; Czernichowski, Piotr; Hollist, Michele

2013-06-11T23:59:59.000Z

138

Fuel Reformation: Microchannel Reactor Design  

DOE Green Energy (OSTI)

Fuel processing is used to extract hydrogen from conventional vehicle fuel and allow fuel cell powered vehicles to use the existing petroleum fuel infrastructure. Kilowatt scale micro-channel steam reforming, water-gas shift and preferential oxida-tion reactors have been developed capable of achieving DOE required system performance metrics. Use of a microchannel design effectively supplies heat to the highly endothermic steam reforming reactor to maintain high conversions, controls the temperature profile for the exothermic water gas shift reactor, which optimizes the overall reaction conversion, and removes heat to prevent the unwanted hydrogen oxidation in the prefer-ential oxidation reactor. The reactors combined with micro-channel heat exchangers, when scaled to a full sized 50 kWe automotive system, will be less than 21 L in volume and 52 kg in weight.

Brooks, Kriston P.; Davis, James M.; Fischer, Christopher M.; King, David L.; Pederson, Larry R.; Rawlings, Gregg C.; Stenkamp, Victoria S.; TeGrotenhuis, Ward E.; Wegeng, Robert S.; Whyatt, Greg A.

2005-09-01T23:59:59.000Z

139

Thermochemical Fuel Reformer Development Project  

Science Conference Proceedings (OSTI)

Thermochemical Fuel Reforming (TCFR) is the recovery of internal combustion engine exhaust heat to chemically convert natural gas into a higher calorific flow fuel stream containing a significant concentration of hydrogen. This technique of recycling the engine exhaust heat can reduce fuel use (heat rate). In addition, the hydrogen enhanced combustion also allows stable engine operation at a higher air-fuel ratio (leaner combustion) which results in very low NOx production. This interim report covers two...

2006-12-11T23:59:59.000Z

140

Environmental fiscal reform (EFR) | Open Energy Information  

Open Energy Info (EERE)

Environmental fiscal reform (EFR) Environmental fiscal reform (EFR) Jump to: navigation, search Tool Summary Name: Environmental fiscal reform (EFR) Agency/Company /Organization: Global Subsidies Initiative (GSI), International Institute for Sustainable Development (IISD), World Bank Phase: Develop Goals, Prepare a Plan, Develop Finance and Implement Projects Topics: Co-benefits assessment, Finance, Market analysis, Policies/deployment programs References: Environmental fiscal reform - What should be done and how to achieve it[1] Reforming fiscal policies to close the gap between economic and ecological efficiencies[2] Overview "The term environmental fiscal reform (EFR) refers to: a range of taxation or pricing instruments that can raise revenue, while simultaneously furthering environmental goals. This is achieved by providing economic

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


141

Solid-State Lighting: Municipal Solid-State Street Lighting Consortium  

NLE Websites -- All DOE Office Websites (Extended Search)

Municipal Solid-State Street Municipal Solid-State Street Lighting Consortium Kickoff Webcast to someone by E-mail Share Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Facebook Tweet about Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Twitter Bookmark Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Google Bookmark Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Delicious Rank Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on Digg Find More places to share Solid-State Lighting: Municipal Solid-State Street Lighting Consortium Kickoff Webcast on AddThis.com... Conferences & Meetings

142

Solid-State Lighting: Using the Street and Parking Facility Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Using the Street and Parking Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool to someone by E-mail Share Solid-State Lighting: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Facebook Tweet about Solid-State Lighting: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Twitter Bookmark Solid-State Lighting: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Google Bookmark Solid-State Lighting: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Delicious Rank Solid-State Lighting: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Digg Find More places to share Solid-State Lighting: Using the Street and

143

Solid-State Lighting: Text-Alternative Version: Evaluating LED Street  

NLE Websites -- All DOE Office Websites (Extended Search)

Evaluating LED Street Lighting Solutions to someone by E-mail Evaluating LED Street Lighting Solutions to someone by E-mail Share Solid-State Lighting: Text-Alternative Version: Evaluating LED Street Lighting Solutions on Facebook Tweet about Solid-State Lighting: Text-Alternative Version: Evaluating LED Street Lighting Solutions on Twitter Bookmark Solid-State Lighting: Text-Alternative Version: Evaluating LED Street Lighting Solutions on Google Bookmark Solid-State Lighting: Text-Alternative Version: Evaluating LED Street Lighting Solutions on Delicious Rank Solid-State Lighting: Text-Alternative Version: Evaluating LED Street Lighting Solutions on Digg Find More places to share Solid-State Lighting: Text-Alternative Version: Evaluating LED Street Lighting Solutions on AddThis.com... Conferences & Meetings Presentations

144

Solid-State Lighting: Considering LEDs for Street and Area Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Considering LEDs for Street and Area Lighting to someone by E-mail Share Solid-State Lighting: Considering LEDs for Street and Area Lighting on Facebook Tweet about Solid-State...

145

Effect of reformer conditions on catalytic reforming of biomass-gasification tars  

Science Conference Proceedings (OSTI)

Parametric tests on catalytic reforming of tars produced in biomass gasification are performed using a bench-scale, fluid-bed catalytic reformer containing a commercial nickel-based catalyst. The product gas composition and yield vary with reformer temperature, space time, and steam: biomass ratio. Under certain catalytic tar reforming conditions, the gas yield increases by 70%; 97% of the tars are cracked into gases; and benzene and naphthalene, the predominant tar species, are virtually eliminated from the product gas.

Kinoshita, C.M.; Wang, Y.; Zhou, J. [Univ. of Hawaii, Honolulu, HI (United States)

1995-09-01T23:59:59.000Z

146

Distributed Bio-Oil Reforming (Presentation)  

DOE Green Energy (OSTI)

This presentation by Bob Evans at the 2007 DOE Hydrogen Program Annual Merit Review Meeting provides information about NREL's distributed bio-oil reforming efforts.

Evans, R. J.; Czernik, S.; French, R.; Ratcliff, M.; Marda, J.; Dean, A. M.

2007-05-15T23:59:59.000Z

147

TransForum v4n2 - Diesel Reformer  

NLE Websites -- All DOE Office Websites (Extended Search)

1 ARGONNE SCIENTISTS TEAM UP TO DEVELOP NEW DIESEL REFORMER Liu tests diesel reformer Argonne's Di-Jia Liu conducted extensive testing of the diesel reformer; his experiments are...

148

Stacey Street, Florida: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Stacey Street, Florida: Energy Resources Stacey Street, Florida: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 26.6983986°, -80.1236545° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":26.6983986,"lon":-80.1236545,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

149

The Network Analysis of Urban Streets: A Primal Approach  

E-Print Network (OSTI)

The network metaphor in the analysis of urban and territorial cases has a long tradition especially in transportation/land-use planning and economic geography. More recently, urban design has brought its contribution by means of the "space syntax" methodology. All these approaches, though under different terms like accessibility, proximity, integration,connectivity, cost or effort, focus on the idea that some places (or streets) are more important than others because they are more central. The study of centrality in complex systems,however, originated in other scientific areas, namely in structural sociology, well before its use in urban studies; moreover, as a structural property of the system, centrality has never been extensively investigated metrically in geographic networks as it has been topologically in a wide range of other relational networks like social, biological or technological. After two previous works on some structural properties of the dual and primal graph representations of urban street ne...

Porta, S; Latora, V; Porta, Sergio; Crucitti, Paolo; Latora, Vito

2005-01-01T23:59:59.000Z

150

Mr. Mark Finkelstein State Street,Associates'L..P. II  

Office of Legacy Management (LM)

Mr. Mark Finkelstein Mr. Mark Finkelstein State Street,Associates'L..P. II 210 Lake Street Ithaca, New York I4856 Dear Mr. Finkelstein: ', 'The Oak Ridge Institute forScience',and Education (ORISEj,has recently sent me the enclosed'radiological survey,conducted at the former Ithaca Gun Company forging building. : The radiationilevels measured during, the'survey were similar to the background'levels in the Ithaca 'area. A number of samples were taken for analysis, and all exhibited background ,concentrations of radioactive,elements: No radioactive,materials that are 'attributable to the former Ithaca Gun Company or to' the activities of the former Atomic.Energy Commission were identified. ;The Department of Energy will prepare.documentation to formally eliminate the site from the Department's Formerly Utilized Sites

151

Fifth Street, Texas: Energy Resources | Open Energy Information  

Open Energy Info (EERE)

Street, Texas: Energy Resources Street, Texas: Energy Resources Jump to: navigation, search Equivalent URI DBpedia Coordinates 29.5982899°, -95.551333° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[{"text":"","title":"","link":null,"lat":29.5982899,"lon":-95.551333,"alt":0,"address":"","icon":"","group":"","inlineLabel":"","visitedicon":""}]}

152

An update on catalytic reforming  

Science Conference Proceedings (OSTI)

The UOP Platforming process is a catalytic reforming process in widespread use throughout the petroleum and petrochemical industries. Since the first unit went onstream in 1949, the process has become a standard feature in refineries worldwide. Over the years, significant improvements have been made in process catalysts and process design. The most recent improvement is the combination of a catalyst called R-72 with a new patented flow scheme, R-72 staged loading, which gives significantly higher yields and provides increased catalyst stability. In this article, the authors describe two types of Platforming processes and the new R-72 staged loading scheme.

Wei, D.H.; Moser, M.D.; Haizmann, R.S.

1996-10-01T23:59:59.000Z

153

Before House Committee on Oversight and Government Reform | Department...  

NLE Websites -- All DOE Office Websites (Extended Search)

Oversight and Government Reform Before House Committee on Oversight and Government Reform Testimony of Daniel Poneman, Deputy Secretary of Energy Before House Committee on...

154

Bio-Derived Liquids to Hydrogen Distributed Reforming Targets...  

NLE Websites -- All DOE Office Websites (Extended Search)

Group includes individuals from DOE, the national laboratories, industry, and academia. Corn Stover Harvest Bio-Derived Liquids Reforming Distributed reforming of biomass derived...

155

Regulatory and Financial Reform of Federal Research Policy: Recommenda...  

NLE Websites -- All DOE Office Websites (Extended Search)

and Financial Reform of Federal Research Policy: Recommendations to the NRC Committee on Research Universities Regulatory and Financial Reform of Federal Research Policy:...

156

Guidance_Application_Federal_Vacancies_Reform_Act_1998.pdf |...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

nceApplicationFederalVacanciesReformAct1998.pdf More Documents & Publications Intelligence Reform and Terroroism Prevention Act - December 17, 2004 Bond Amendment, Security...

157

Diesel Reforming for Fuel Cell Auxiliary Power Units  

DOE Green Energy (OSTI)

This objective of this project was to develop technology suitable for onboard reforming of diesel. The approach was to examine catalytic partial oxidation and steam reforming.

Borup, R.; Parkinson, W. J.; Inbody, M.; Brosha, E.L.; Guidry, D.R.

2005-01-27T23:59:59.000Z

158

Fuel cell integrated with steam reformer  

DOE Patents (OSTI)

A H.sub.2 -air fuel cell integrated with a steam reformer is disclosed wherein a superheated water/methanol mixture is fed to a catalytic reformer to provide a continuous supply of hydrogen to the fuel cell, the gases exhausted from the anode of the fuel cell providing the thermal energy, via combustion, for superheating the water/methanol mixture.

Beshty, Bahjat S. (Lower Makefield, PA); Whelan, James A. (Bricktown, NJ)

1987-01-01T23:59:59.000Z

159

School Finance Reform: Assessing General Equilibrium Effects  

E-Print Network (OSTI)

In 1994 the state of Michigan implemented one of the most comprehensive school finance reforms undertaken to date in any of the states. Understanding the effects of the reform is thus of value in informing other potential reform initiatives. In addition, the reform and associated changes in the economic environment provide an opportunity to assess whether a simple general equilibrium model can be of value in framing the study of such reform initiatives. In this paper, we present and use such a model to derive predictions about the effects of the reform on housing prices and neighborhood demographic compositions. Broadly, our analysis implies that the effects of the reform and changes in the economic environment are likely to have been reflected primarily in housing prices and only modestly on neighborhood demographics. We find that evidence for the Detroit metropolitan area from the decade encompassing the reform is largely consistent with the predictions of the model (JEL codes: H42, H71, H73, I22).

Maria Marta Ferreyra

2007-01-01T23:59:59.000Z

160

Octane Number Prediction in a Reforming Plant  

Science Conference Proceedings (OSTI)

In this work a neural network for the prediction of the complex and non-linear behavior of a Catalytic Reforming of a refinery has been developed. In a fuel, refinery reforming is a conversion process to increase octane number (RON) of the desulphurated ...

E. Chibaro

2000-07-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


161

Methanol Steam Reformer on a Silicon Wafer  

DOE Green Energy (OSTI)

A study of the reforming rates, heat transfer and flow through a methanol reforming catalytic microreactor fabricated on a silicon wafer are presented. Comparison of computed and measured conversion efficiencies are shown to be favorable. Concepts for insulating the reactor while maintaining small overall size and starting operation from ambient temperature are analyzed.

Park, H; Malen, J; Piggott, T; Morse, J; Sopchak, D; Greif, R; Grigoropoulos, C; Havstad, M; Upadhye, R

2004-04-15T23:59:59.000Z

162

New model accurately predicts reformate composition  

Science Conference Proceedings (OSTI)

Although naphtha reforming is a well-known process, the evolution of catalyst formulation, as well as new trends in gasoline specifications, have led to rapid evolution of the process, including: reactor design, regeneration mode, and operating conditions. Mathematical modeling of the reforming process is an increasingly important tool. It is fundamental to the proper design of new reactors and revamp of existing ones. Modeling can be used to optimize operating conditions, analyze the effects of process variables, and enhance unit performance. Instituto Mexicano del Petroleo has developed a model of the catalytic reforming process that accurately predicts reformate composition at the higher-severity conditions at which new reformers are being designed. The new AA model is more accurate than previous proposals because it takes into account the effects of temperature and pressure on the rate constants of each chemical reaction.

Ancheyta-Juarez, J.; Aguilar-Rodriguez, E. (Inst. Mexicano del Petroleo, Mexico City (Mexico))

1994-01-31T23:59:59.000Z

163

Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium  

NLE Websites -- All DOE Office Websites (Extended Search)

Market-Based Programs Printable Version Share this resource Send a link to Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium to someone by E-mail Share Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Facebook Tweet about Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Twitter Bookmark Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Google Bookmark Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Delicious Rank Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on Digg Find More places to share Solid-State Lighting: DOE Municipal Solid-State Street Lighting Consortium on AddThis.com... LED Lighting Facts

164

Street-based Topological Representations and Analyses for Predicting Traffic Flow in GIS  

E-Print Network (OSTI)

It is well received in the space syntax community that traffic flow is significantly correlated to a morphological property of streets, which are represented by axial lines, forming a so called axial map. The correlation co-efficient (R square value) approaches 0.8 and even a higher value according to the space syntax literature. In this paper, we study the same issue using the Hong Kong street network and the Hong Kong Annual Average Daily Traffic (AADT) datasets, and find surprisingly that street-based topological representations (or street-street topologies) tend to be better representations than the axial map. In other words, vehicle flow is correlated to a morphological property of streets better than that of axial lines. Based on the finding, we suggest the street-based topological representations as an alternative GIS representation, and the topological analyses as a new analytical means for geographic knowledge discovery.

Jiang, Bin

2007-01-01T23:59:59.000Z

165

Solid-State Lighting: Member Case Studies: LED Street Lighting Programs in  

NLE Websites -- All DOE Office Websites (Extended Search)

Member Case Studies: LED Street Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) to someone by E-mail Share Solid-State Lighting: Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) on Facebook Tweet about Solid-State Lighting: Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) on Twitter Bookmark Solid-State Lighting: Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) on Google Bookmark Solid-State Lighting: Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) on Delicious Rank Solid-State Lighting: Member Case Studies: LED Street Lighting Programs in Algona (IA), Asheville (NC), and Boston (MA) on Digg

166

TransWall  

Science Conference Proceedings (OSTI)

Nowadays, imagining modern buildings without glass is difficult, and glass walls can be found almost everywhere around us. Glass has been one of the most valued materials owing to its transparency. Glass walls' transparency in modern architecture involves ...

Heejeong Heo; Seungki Kim; Hyungkun Park; Jeeyong Chung; Geehyuk Lee; Woohun Lee

2013-07-01T23:59:59.000Z

167

Large-Eddy Simulation of Flow and Pollutant Transport in Street Canyons of Different Building-Height-to-Street-Width Ratios  

Science Conference Proceedings (OSTI)

This study employs a large-eddy simulation technique to investigate the flow, turbulence structure, and pollutant transport in street canyons of building-height-to-street-width (aspect) ratios of 0.5, 1.0, and 2.0 at a Reynolds number of 12 000 ...

Chun-Ho Liu; Mary C. Barth; Dennis Y. C. Leung

2004-10-01T23:59:59.000Z

168

Prismatic wall heater  

Science Conference Proceedings (OSTI)

A prismatic beam concentrator mounted at the top of two adjacent walls so as to receive a rectangular incipient beam of diffused sunlight and emit a vertical concentrated sheet beam through a cavity between the walls to a mirror which reflects the beam at right angles onto a radiant iron bar at the base of one wall, as a source of supplemental household heat.

Clegg, J. E.

1985-07-09T23:59:59.000Z

169

Autothermal Cyclic Reforming Based H2 Generating & Dispensing System  

E-Print Network (OSTI)

Pressure Reforming Comp- ressor 100 psig 100 psig Reformer H2 PSA SyngasNatural Gas Low Pressure Reforming CMP Syngas 5 psig5 psig Reformer CMP 100 psig H2 PSA Natural Gas Syngas CMP HX CMP HX Thermal Reliability (Eliminates Syngas Compressor) Advantages 70-80%70-80%Thermal Efficiency (Excludes Electricity

170

Electricity reform in developing and transition countries: A reappraisal  

E-Print Network (OSTI)

Electricity reform in developing and transition countries: A reappraisal J.H. Williams, R. Ghanadan-oriented reforms in their electric power sectors. Despite the widespread adoption of a standard policy model features of non-OECD electricity reform and reappraises reform policies and underlying assumptions

Kammen, Daniel M.

171

Diesel Reforming for Solid Oxide Fuel Cell Application  

DOE Green Energy (OSTI)

This presentation discusses the development of a diesel reforming catalyst and catalytic system development.

Liu, D-J.; Sheen, S-H.; Krumpelt, M.

2005-01-27T23:59:59.000Z

172

Fluidized wall for protecting fusion chamber walls  

DOE Patents (OSTI)

Apparatus for protecting the inner wall of a fusion chamber from microexplosion debris, x-rays, neutrons, etc. produced by deuterium-tritium (DT) targets imploded within the fusion chamber. The apparatus utilizes a fluidized wall similar to a waterfall comprising liquid lithium or solid pellets of lithium-ceramic, the waterfall forming a blanket to prevent damage of the structural materials of the chamber.

Maniscalco, James A. (Danville, CA); Meier, Wayne R. (Livermore, CA)

1982-01-01T23:59:59.000Z

173

Before the House Oversight and Government Reform Subcommittee on  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Oversight and Government Reform Subcommittee on Oversight and Government Reform Subcommittee on Technology, Information Policy, Intergovernmental Relations, and Procurement Reform Before the House Oversight and Government Reform Subcommittee on Technology, Information Policy, Intergovernmental Relations, and Procurement Reform Before the Subcommittee on Technology, Information Policy, Intergovernmental Relations and Procurement Reform, Committee on Oversight and Government Reform, United States House of Representatives Written Statement By: Owen Barwell, Acting Chief Financial Officer, United States Department of Energy Subject: DOE Financial Information Systems Final_Testimony_for_Owen_Barwell.pdf More Documents & Publications AL2010-03.pdf Request for Information - Operations and Maintenance (O & M) Support

174

Internal reforming fuel cell assembly with simplified fuel feed  

DOE Patents (OSTI)

A fuel cell assembly in which fuel cells adapted to internally reform fuel and fuel reformers for reforming fuel are arranged in a fuel cell stack. The fuel inlet ports of the fuel cells and the fuel inlet ports and reformed fuel outlet ports of the fuel reformers are arranged on one face of the fuel cell stack. A manifold sealing encloses this face of the stack and a reformer fuel delivery system is arranged entirely within the region between the manifold and the one face of the stack. The fuel reformer has a foil wrapping and a cover member forming with the foil wrapping an enclosed structure.

Farooque, Mohammad (Huntington, CT); Novacco, Lawrence J. (Brookfield, CT); Allen, Jeffrey P. (Naugatuck, CT)

2001-01-01T23:59:59.000Z

175

Computational Fluid Dynamics Simulation of Steam Reforming and Autothermal Reforming for Fuel Cell Applications.  

E-Print Network (OSTI)

??With the increasing demand for fuel cell applications in transportation, the performance of reformers using gasoline or diesel as the fuel needs to be optimized.… (more)

Shi, Liming

2009-01-01T23:59:59.000Z

176

Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting  

NLE Websites -- All DOE Office Websites (Extended Search)

Webcast: Municipal Solid-State Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool to someone by E-mail Share Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Facebook Tweet about Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Twitter Bookmark Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Google Bookmark Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Delicious Rank Solid-State Lighting: Webcast: Municipal Solid-State Street Lighting Consortium Retrofit Financial Analysis Tool on Digg

177

Solid-State Lighting: Text-Alternative Version: Using the Street and  

NLE Websites -- All DOE Office Websites (Extended Search)

Using Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool to someone by E-mail Share Solid-State Lighting: Text-Alternative Version: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Facebook Tweet about Solid-State Lighting: Text-Alternative Version: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Twitter Bookmark Solid-State Lighting: Text-Alternative Version: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Google Bookmark Solid-State Lighting: Text-Alternative Version: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on Delicious Rank Solid-State Lighting: Text-Alternative Version: Using the Street and Parking Facility Lighting Retrofit Financial Analysis Tool on

178

Bank Regulation and Mortgage Market Reform  

E-Print Network (OSTI)

America’s Housing Finance Market: A Report To Congress”,Subordinated Debt: A Capital Markets Approach to BankBank Regulation and Mortgage Market Reform Dwight M. Jaffee

Jaffee, Dwight M.

2011-01-01T23:59:59.000Z

179

Electricity reform abroad and US investment  

SciTech Connect

This report reviews and analyzes the recent electricity reforms in Argentina, Australia, and the United Kingdom (UK) to illustrate how different models of privatization and reform have worked in practice. This report also analyzes the motivations of the U.S. companies who have invested in the electricity industries in these countries, which have become the largest targets of U.S. foreign investment in electricity. Two calculations of foreign investment are used. One is the foreign direct investment series produced by the U.S. Department of Commerce. The other is based on transactions in electric utilities of the three countries. The electricity reform and privatization experiences reviewed may offer some insight as to how the U.S. electricity industry might develop as a result of recent domestic reform efforts and deregulation at the state and national levels. 126 refs., 23 figs., 27 tabs.

1997-10-01T23:59:59.000Z

180

Distributed Reforming of Biomass Pyrolysis Oils (Presentation...  

NLE Websites -- All DOE Office Websites (Extended Search)

gas (0.5% H 2 ) System Definition (1500 kgday station used for H2A analysis) Capital Costs Bio-Oil Reforming H2A Analysis Bio-Oil Case (Ethanol Case) Bio-oil Storage Tank...

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


181

Device for cooling and humidifying reformate  

Science Conference Proceedings (OSTI)

Devices for cooling and humidifying a reformate stream from a reforming reactor as well as related methods, modules and systems includes a heat exchanger and a sprayer. The heat exchanger has an inlet, an outlet, and a conduit between the inlet and the outlet. The heat exchanger is adapted to allow a flow of a first fluid (e.g. water) inside the conduit and to establish a heat exchange relationship between the first fluid and a second fluid (e.g. reformate from a reforming reactor) flowing outside the conduit. The sprayer is coupled to the outlet of the heat exchanger for spraying the first fluid exiting the heat exchanger into the second fluid.

Zhao, Jian Lian (Belmont, MA); Northrop, William F. (Ann Arbor, MI)

2008-04-08T23:59:59.000Z

182

Liquid fuel reformer development: Autothermal reforming of Diesel fuel  

DOE Green Energy (OSTI)

Argonne National Laboratory is developing a process to convert hydrocarbon fuels to clean hydrogen feeds for a polymer electrolyte fuel cell. The process incorporates an autothermal reforming catalyst that can process hydrocarbon feeds at lower temperatures than existing commercial catalysts. The authors have tested the catalyst with three diesel-type fuels: hexadecane, certified low-sulfur grade 1 diesel, and a standard grade 2 diesel. Hexadecane yielded products containing 60% hydrogen on a dry, nitrogen-free basis at 850 C, while maximum hydrogen product yields for the two diesel fuels were near 50%. Residual products in all cases included CO, CO{sub 2}, ethane, and methane. Further studies with grade 1 diesel showed improved conversion as the water:fuel ratio was increased from 1 to 2 at 850 C. Soot formation was reduced when the oxygen:carbon ratio was maintained at 1 at 850 C. There were no significant changes in hydrogen yield as the space velocity and the oxygen:fuel ratio were varied. Tests with a microchannel monolithic catalyst yielded similar or improved hydrogen levels at higher space velocities than with extruded pellets in a packed bed.

Pereira, C.; Bae, J-M.; Ahmed, S.; Krumpelt, M.

2000-07-24T23:59:59.000Z

183

Reforming of fuel inside fuel cell generator  

DOE Patents (OSTI)

Disclosed is an improved method of reforming a gaseous reformable fuel within a solid oxide fuel cell generator, wherein the solid oxide fuel cell generator has a plurality of individual fuel cells in a refractory container, the fuel cells generating a partially spent fuel stream and a partially spent oxidant stream. The partially spent fuel stream is divided into two streams, spent fuel stream 1 and spent fuel stream 2. Spent fuel stream 1 is burned with the partially spent oxidant stream inside the refractory container to produce an exhaust stream. The exhaust stream is divided into two streams, exhaust stream 1 and exhaust stream 2, and exhaust stream 1 is vented. Exhaust stream 2 is mixed with spent fuel stream 2 to form a recycle stream. The recycle stream is mixed with the gaseous reformable fuel within the refractory container to form a fuel stream which is supplied to the fuel cells. Also disclosed is an improved apparatus which permits the reforming of a reformable gaseous fuel within such a solid oxide fuel cell generator. The apparatus comprises a mixing chamber within the refractory container, means for diverting a portion of the partially spent fuel stream to the mixing chamber, means for diverting a portion of exhaust gas to the mixing chamber where it is mixed with the portion of the partially spent fuel stream to form a recycle stream, means for injecting the reformable gaseous fuel into the recycle stream, and means for circulating the recycle stream back to the fuel cells. 1 fig.

Grimble, R.E.

1988-03-08T23:59:59.000Z

184

Reforming of fuel inside fuel cell generator  

DOE Patents (OSTI)

Disclosed is an improved method of reforming a gaseous reformable fuel within a solid oxide fuel cell generator, wherein the solid oxide fuel cell generator has a plurality of individual fuel cells in a refractory container, the fuel cells generating a partially spent fuel stream and a partially spent oxidant stream. The partially spent fuel stream is divided into two streams, spent fuel stream I and spent fuel stream II. Spent fuel stream I is burned with the partially spent oxidant stream inside the refractory container to produce an exhaust stream. The exhaust stream is divided into two streams, exhaust stream I and exhaust stream II, and exhaust stream I is vented. Exhaust stream II is mixed with spent fuel stream II to form a recycle stream. The recycle stream is mixed with the gaseous reformable fuel within the refractory container to form a fuel stream which is supplied to the fuel cells. Also disclosed is an improved apparatus which permits the reforming of a reformable gaseous fuel within such a solid oxide fuel cell generator. The apparatus comprises a mixing chamber within the refractory container, means for diverting a portion of the partially spent fuel stream to the mixing chamber, means for diverting a portion of exhaust gas to the mixing chamber where it is mixed with the portion of the partially spent fuel stream to form a recycle stream, means for injecting the reformable gaseous fuel into the recycle stream, and means for circulating the recycle stream back to the fuel cells.

Grimble, Ralph E. (Finleyville, PA)

1988-01-01T23:59:59.000Z

185

Intelligent street lighting application for electric power distribution systems the business case for smartgrid technology.  

E-Print Network (OSTI)

??This research project builds upon previous work related to intelligent and energy efficient lighting in modern street and outdoor lighting systems. The concept of implementing… (more)

Davis, Wesley O'Brian Sr.

2011-01-01T23:59:59.000Z

186

Electric, Gas, Water, Heating, Refrigeration, and Street Railways Facilities and Service (South Dakota)  

Energy.gov (U.S. Department of Energy (DOE))

This legislation contains provisions for facilities and service related to electricity, natural gas, water, heating, refrigeration, and street railways. The chapter addresses the construction and...

187

Heat Transfer Limitations in Hydrogen Production Via Steam Reformation: The Effect of Reactor Geometry  

E-Print Network (OSTI)

Ratio Parameters in Steam-Reforming Hydrogen productionan Insufficient Parameter in the Steam-Reforming Process,”Impurities on the Methanol Steam-Reforming Process for Fuel

Vernon, David R.; Davieau, David D.; Dudgeon, Bryce A.; Erickson, Paul A.

2006-01-01T23:59:59.000Z

188

Tokamak reactor first wall  

DOE Patents (OSTI)

This invention relates to an improved first wall construction for a tokamak fusion reactor vessel, or other vessels subjected to similar pressure and thermal stresses.

Creedon, R.L.; Levine, H.E.; Wong, C.; Battaglia, J.

1984-11-20T23:59:59.000Z

189

Collector: storage wall systems  

SciTech Connect

Passive Trombe wall systems require massive masonry walls to minimize large temperature swings and movable night insulation to prevent excessive night heat losses. As a solar energy collection system, Trombe wall systems have low efficiencies because of the nature of the wall and, if auxiliary heat is needed, because of absorption of this heat. Separation of collector and storage functions markedly improves the efficiency. A simple fiberglass absorber can provide high efficiency while phase change storage provides a compact storage unit. The need for movable insulation is obviated.

Boardman, H.

1980-01-01T23:59:59.000Z

190

Pecan Street Project, Inc. Smart Grid Demonstration Project | Open Energy  

Open Energy Info (EERE)

Project, Inc. Smart Grid Demonstration Project Project, Inc. Smart Grid Demonstration Project Jump to: navigation, search Project Lead Pecan Street Project, Inc. Country United States Headquarters Location Austin, Texas Recovery Act Funding $10,403,570.00 Total Project Value $24,656,485.00 Coordinates 30.267153°, -97.7430608° Loading map... {"minzoom":false,"mappingservice":"googlemaps3","type":"ROADMAP","zoom":14,"types":["ROADMAP","SATELLITE","HYBRID","TERRAIN"],"geoservice":"google","maxzoom":false,"width":"600px","height":"350px","centre":false,"title":"","label":"","icon":"","visitedicon":"","lines":[],"polygons":[],"circles":[],"rectangles":[],"copycoords":false,"static":false,"wmsoverlay":"","layers":[],"controls":["pan","zoom","type","scale","streetview"],"zoomstyle":"DEFAULT","typestyle":"DEFAULT","autoinfowindows":false,"kml":[],"gkml":[],"fusiontables":[],"resizable":false,"tilt":0,"kmlrezoom":false,"poi":true,"imageoverlays":[],"markercluster":false,"searchmarkers":"","locations":[]}

191

A LIMITED LIABILITY PARTNERSHIP 1050 Thomas Jefferson Street, NW  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

A LIMITED LIABILITY PARTNERSHIP A LIMITED LIABILITY PARTNERSHIP 1050 Thomas Jefferson Street, NW Seventh Floor Washington, DC 20007 (202) 298-1800 Phone (202) 338-2416 Fax MEMORANDUM TO: DOE Office of General Counsel FROM: Doug Smith DATE: August 29, 2013 RE: Record of Communication Concerning Ceiling Fan and Ceiling Fan Light Kit Framework Document-Docket No. EERE-2012-BT-STD-0045 This memo provides an overview of communications made to DOE staff on the subject of possible changes to standards and test procedures for ceiling fans and ceiling fan light kits. The communications occurred at a meeting held at 10:30 a.m. on August 20, 2013, following the close of the comment period on the initial framework document for ceiling fans and light kits. The meeting attendees included:

192

The Honorable Robert E. Williams 44 W. Washington Street  

Office of Legacy Management (LM)

SEC ; : ' SEC ; : ' ,-<- I ;;;s The Honorable Robert E. Williams 44 W. Washington Street Shelbyville, Indiana 46176 Dear Mayor Williams: Secretary of Energy Hazel O'Leary has announced a new approach to openness in the Department of Energy (DOE) and its communications with the public. In support of this initiative, we are pleased to forward the enclosed information related to the former General Electric Co. site in your jurisdiction that performed work for DOE or its predecessor agencies. This information is provided for your information, use, and retention. DOE's Formerly Utilized Sites Remedial Action Program is responsible for identification of sites used by DOE's predecessor agencies, determining their current radiological condition and, where it has authority, performing

193

STATE OF WASHINGTON DEPARTMENT OF COMMERCE 1011 Plum Street SE  

NLE Websites -- All DOE Office Websites (Extended Search)

STATE OF WASHINGTON STATE OF WASHINGTON DEPARTMENT OF COMMERCE 1011 Plum Street SE  PO Box 42525  Olympia, Washington 98504-2525  (360) 725-4000 www.commerce.wa.gov July 33, 2013 Roland J. Risser Building Technologies Program Manager Office of Energy Efficiency and Renewable Energy U.S. Department of Energy 1000 Independence Avenue SW, Mail Stop EE-2J Washington, DC 20585-0121 RE: State Certification of Residential and Commercial Building Energy Codes Dear Mr. Risser: In compliance with Title III of the Energy Conservation and Production Act (ECPA) of 1976, as amended, this is to certify that the State of Washington has adopted the 2012 Edition, Washington State Energy Code, which meets or exceeds the 2012 version of the International Energy Conservation Code (IECC) for low-rise residential

194

Planning Department 168 North Edwards Street Post Office Drawer L  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Department Department 168 North Edwards Street Post Office Drawer L Independence, California 93526 Phone: (619) 872-1168 FAX: (619) 873-5695 E-Mail: bmettam@telis.org January 30, 1998 U. S. Department of Energy Office of General Counsel, GC-52 1000 Independence Avenue, SW Washington, D.C. 20585 NOTICE OF INQUIRY CONCERNING PREPARATION OF REPORT TO CONGRESS ON THE PRICE-ANDERSON ACT Thank you for the opportunity to comment prior to the Department of Energy's report to Congress concerning the continuation or modification of the provisions of the Price-Anderson Act (the "Act"). The thirty-day notice period does not allow sufficient time for the County to conduct a through analysis of the potential impact to local governments of changes to the Act. The following general

195

Self-organizing traffic lights at multiple-street intersections  

E-Print Network (OSTI)

Summary: Traffic light coordination is a complex problem. In this paper, we extend previous work on an abstract model of city traffic to allow for multiple street intersections. We test a self-organizing method in our model, showing that it is close to theoretical optima and superior to a traditional method of traffic light coordination. Abstract: The elementary cellular automaton following rule 184 can mimic particles flowing in one direction at a constant speed. This automaton can therefore model highway traffic. In a recent paper, we have incorporated intersections regulated by traffic lights to this model using exclusively elementary cellular automata. In such a paper, however, we only explored a rectangular grid. We now extend our model to more complex scenarios employing an hexagonal grid. This extension shows first that our model can readily incorporate multiple-way intersections and hence simulate complex scenarios. In addition, the current extension allows us to study and evaluate the behavior of two...

Gershenson, Carlos

2011-01-01T23:59:59.000Z

196

Hydrogen generation utilizing integrated CO2 removal with steam reforming  

DOE Patents (OSTI)

A steam reformer may comprise fluid inlet and outlet connections and have a substantially cylindrical geometry divided into reforming segments and reforming compartments extending longitudinally within the reformer, each being in fluid communication. With the fluid inlets and outlets. Further, methods for generating hydrogen may comprise steam reformation and material adsorption in one operation followed by regeneration of adsorbers in another operation. Cathode off-gas from a fuel cell may be used to regenerate and sweep the adsorbers, and the operations may cycle among a plurality of adsorption enhanced reformers to provide a continuous flow of hydrogen.

Duraiswamy, Kandaswamy; Chellappa, Anand S

2013-07-23T23:59:59.000Z

197

Walls and Windows  

SciTech Connect

Energy travels in and out of a building through the walls and windows by means of conduction, convection, and radiation. The walls and windows, complex systems in themselves, are part of the overall building system. A wall system is composed of multiple layers that work in concert to provide shelter from the exterior weather. Wall systems vary in the degree to which they provide thermal resistance, moisture resistance, durability, and thermal storage. High tech windows are now available that can resist radiation heat transfer while still providing light and visibility. The combination of walls and windows within the building system can be adapted to meet a wide range of environmental conditions, recognizing that the best building envelope system for one climate may not be the first choice for another location.

Stovall, Therese K [ORNL

2007-01-01T23:59:59.000Z

198

Assistance in local government energy conservation in Massachusetts. Energy management in municipal street lighting  

SciTech Connect

This report presents strategies to reduce the energy used in street lighting and, at the same time, reduce or stabilize the cost of street lighting to municipalities. The strategies described are based upon the existing rate structure and institutional arrangements whereby municipalities purchase a total lighting service under long-term contract from a utility.

1979-01-01T23:59:59.000Z

199

UC Davis Medical Education Building | 4610 X Street | Room 1222 & 2222 ONLINE REGISTRATION  

E-Print Network (OSTI)

UC Davis Medical Education Building | 4610 X Street | Room 1222 & 2222 ONLINE REGISTRATION/ TECHNOLOGIST SYMPOSIUM Advances In Cardiovascular Medical and Surgical Care SAVE THE DATE Saturday, May 5, 2012-734-5512, janine.neely@ucdmc.ucdavis.edu. LOCATION UC Davis Medical Education Building 4610 X Street, Room 1222

Hammock, Bruce D.

200

Integrated Google Maps and Smooth Street View Videos for Route Planning National Taiwan University  

E-Print Network (OSTI)

Integrated Google Maps and Smooth Street View Videos for Route Planning Chi Peng National Taiwan that takes start and end points as the input, and will automatically connect to the Google Maps with Street a smooth scenic video from the starting point to the destination, which combines the Google Maps to provide

Ouhyoung, Ming

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


201

DOE - Office of Legacy Management -- GSA 39th Street Warehouse - IL 02  

Office of Legacy Management (LM)

GSA 39th Street Warehouse - IL 02 GSA 39th Street Warehouse - IL 02 FUSRAP Considered Sites Site: GSA 39TH STREET WAREHOUSE (IL.02 ) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: 1716 West Pershing Road , Chicago , Illinois IL.02-1 Evaluation Year: 1985 IL.02-2 IL.02-3 Site Operations: Stored radioactive materials. IL.02-1 IL.02-2 Site Disposition: Eliminated - Radiation levels below criteria IL.02-1 Radioactive Materials Handled: Yes Primary Radioactive Materials Handled: Unknown IL.02-2 Radiological Survey(s): Yes IL.02-1 IL.02-4 Site Status: Eliminated from consideration under FUSRAP Also see Documents Related to GSA 39TH STREET WAREHOUSE IL.02-1 - Report (DOE/EV-0005/9); Formerly Utilized MED/AEC Sites Remedial Action Program Radiological Survey of the Former GSA 39th Street

202

Thermally integrated staged methanol reformer and method  

DOE Green Energy (OSTI)

A thermally integrated two-stage methanol reformer including a heat exchanger and first and second reactors colocated in a common housing in which a gaseous heat transfer medium circulates to carry heat from the heat exchanger into the reactors. The heat transfer medium comprises principally hydrogen, carbon dioxide, methanol vapor and water vapor formed in a first stage reforming reaction. A small portion of the circulating heat transfer medium is drawn off and reacted in a second stage reforming reaction which substantially completes the reaction of the methanol and water remaining in the drawn-off portion. Preferably, a PrOx reactor will be included in the housing upstream of the heat exchanger to supplement the heat provided by the heat exchanger.

Skala, Glenn William (Churchville, NY); Hart-Predmore, David James (Rochester, NY); Pettit, William Henry (Rochester, NY); Borup, Rodney Lynn (East Rochester, NY)

2001-01-01T23:59:59.000Z

203

Fundamental kinetic modeling of the catalytic reforming process  

Science Conference Proceedings (OSTI)

In this work, a fundamental kinetic model for the catalytic reforming process has been developed. The complex network of elementary steps and molecular reactions occurring in catalytic reforming has been generated through a computer algorithm characterizing ...

Rogelio Sotelo-Boyas / Gilbert F. Froment; Rayford G. Anthony

2005-01-01T23:59:59.000Z

204

Electricity reform in Chile : lessons for developing countries  

E-Print Network (OSTI)

Chile was the first country in the world to implement a comprehensive reform of its electricity sector in the recent period. Among developing countries only Argentina has had a comparably comprehensive and successful reform. ...

Pollitt, Michael G.

2004-01-01T23:59:59.000Z

205

REFORMING PROCESSES FOR MICRO COMBINED HEAT AND POWER SYSTEM BASED ON SOLID OXIDE FUEL CELL  

E-Print Network (OSTI)

and energy balance, different types of fuel reforming including steam reforming, autothermal reforming technologies. Steam reforming, partial oxidation and autothermal reforming are the three major fuel of an activated carbon bed. Prior to enter the SOFC stack, the fuel is pre-reformed (methane is partially

Liso, Vincenzo

206

Before the House Oversight and Government Reform Subcommittee...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Government Management, Organization, and Procurement Before the House Oversight and Government Reform Subcommittee on Government Management, Organization, and Procurement Before...

207

Cost Analysis of Bio-Derived Liquids Reforming  

E-Print Network (OSTI)

) steam reforming C2H5OH + H2O Ã? 2CO + 4H2 6) Water gas shift 7) Methanation 8) Coking from CH4 (methane Ethanol Reforming Options Gas Phase Liquid Phase Virent Steam Partial Oxidation Reforming GE (SCPO) decomposition C2H5OH Ã? CH4 + CO + H2 steam reforming CH4 + 2H2O Ã? 4H2 + CO2 3) C2H5OH dehydrogenation

208

New Jersey Refinery Catalytic Reforming/High Pressure Downstream ...  

U.S. Energy Information Administration (EIA)

New Jersey Refinery Catalytic Reforming/High Pressure Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

209

Arkansas Refinery Catalytic Reforming/High Pressure Downstream ...  

U.S. Energy Information Administration (EIA)

Arkansas Refinery Catalytic Reforming/High Pressure Downstream Charge Capacity as of January 1 (Barrels per Stream Day)

210

Integrated autothermal reactor concepts for oxidative coupling and reforming of  

E-Print Network (OSTI)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 Oxidative coupling and steam reforming of methane . . . . . . . . . . 5 1.4 This thesis of methane . . . . . . . . . . . . . . . . . . . 23 2.4 Only steam reforming of methane#12;Integrated autothermal reactor concepts for oxidative coupling and reforming of methane #12

Twente, Universiteit

211

Demonstration of LED Street Lighting in Kansas City, MO  

SciTech Connect

Nine different streetlighting products were installed on various streets in Kansas City, Missouri during February, 2011, to evaluate their performance relative to the incumbent high-pressure sodium (HPS) lighting. The applications investigated included 100 W, 150 W, 250 W, and 400 W HPS installations. Initial measurements and comparisons included power, illuminance, and luminance; sample illuminance readings have continued at each of the nine locations at roughly 1,000-hour operating intervals since then. All of the LED products consumed less power than their HPS counterparts—with a mean difference of 39% and a range of 31% to 51%—but they also emitted 31% fewer lumens, on average. The net result is just a 15% increase in mean efficacy. Applying the city’s stringent light loss factors to the initial measured data meant that five of the LED products (and two of the HPS luminaires) were predicted to eventually fail to meet the specified mean illuminance over their lifetimes; however, the specified light loss levels are not expected to be reached by the LED products until some distant future date (between 12 and 30 years after installation according to manufacturer specification sheet estimates). The practical value of designing streetlighting systems to meet illumination requirements more than 15 years in the future is questioned. Numerous sources of variation in field measurements are noted throughout the report, particularly seasonal influences such as ambient temperature and foliage that are evident in the time-series illuminance data.

Kinzey, Bruce R.; Royer, Michael P.; Hadjian, M.; Kauffman, Rick

2013-06-10T23:59:59.000Z

212

Collaborative process and the transformation of the urban environment : wall, street, and scaffolding on Massachusetts Avenue in Boston  

E-Print Network (OSTI)

This thesis addresses two questions: how to develop a process of collaborative building in cities, and what kind of public places to make in cities. More generally: how can urban dwellers re-engage with urban architecture ...

Carr, James D. (James David)

1994-01-01T23:59:59.000Z

213

Legal aspects of Internet governance reform  

Science Conference Proceedings (OSTI)

The Internet has moved on from its early almost lawless nature. There are now multiple organisations and legal aspects associated with Internet governance. Whether the issue on the Internet is network security, intellectual property rights (IPRs), e-commerce, ... Keywords: ICANN, WGIG, WSIS, cybercrime, framework, governance, internet, law, reform, treaty

David Satola

2007-01-01T23:59:59.000Z

214

Catalytic partial oxidation reforming of hydrocarbon fuels.  

DOE Green Energy (OSTI)

The polymer electrolyte fuel cell (PEFC) is the primary candidate as the power source for light-duty transportation systems. On-board conversion of fuels (reforming) to supply the required hydrogen has the potential to provide the driving range that is typical of today's automobiles. Petroleum-derived fuels, gasoline or some distillate similar to it, are attractive because of their existing production, distribution, and retailing infrastructure. The fuel may be either petroleum-derived or other alternative fuels such as methanol, ethanol, natural gas, etc. [1]. The ability to use a variety of fuels is also attractive for stationary distributed power generation [2], such as in buildings, or for portable power in remote locations. Argonne National Laboratory has developed a catalytic reactor based on partial oxidation reforming that is suitable for use in light-duty vehicles powered by fuel cells. The reactor has shown the ability to convert a wide variety of fuels to a hydrogen-rich gas at less than 800 C, temperatures that are several hundreds of degrees lower than alternative noncatalytic processes. The fuel may be methanol, ethanol, natural gas, or petroleum-derived fuels that are blends of various hydrocarbons such as paraffins, olefins, aromatics, etc., as in gasoline. This paper will discuss the results obtained from a bench-scale (3-kWe) reactor., where the reforming of gasoline and natural gas generated a product gas that contained 38% and 42% hydrogen on a dry basis at the reformer exit, respectively.

Ahmed, S.

1998-09-21T23:59:59.000Z

215

March 16, 2010, Safety and Security Reform Roundtable - Agenda  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Safety and Security Reform Roundtable Safety and Security Reform Roundtable Forrestal Building, Washington, DC March 16 th , 2010 1:00 PM (EST) AGENDA * Introduction of Union Leaders Glenn Podonsky, Chief Health, Safety and Security Officer * Welcome/Introductory Remarks on Reform Goals Dan Poneman, Deputy Secretary * Reform Status and Approach - Oversight, Directives, Mission Support Glenn Podonsky, Chief Health, Safety and Security Officer * Discussion Forum - Union Feedback - Feedback on oversight reform initiatives - Priority safety issues - Experience in collaborative focus group efforts - Recommendations for a path forward * Operating Organization Perspectives 1. Tom D'Agostino Administrator, National Nuclear Security Administration 2. Steven Koonin Under Secretary for Science

216

Bio-Derived Liquids to Hydrogen Distributed Reforming Targets (Presentation)  

NLE Websites -- All DOE Office Websites (Extended Search)

Distributed Reforming Targets Arlene F. Anderson Technology Development Manager, U.S. DOE Office of Energy Efficiency and Renewable Energy Hydrogen, Fuel Cells and Infrastructure Technologies Program Bio-Derived Liquids to Hydrogen Distributed Reforming Working Group and Hydrogen Production Technical Team Review November 6, 2007 Bio-Derived Liquids to Hydrogen Distributed Reforming Working Group (BILIWG) The Bio-Derived Liquids to Hydrogen Distributed Reforming Working Group (BILIWG), launched in October 2006, provides a forum for effective communication and collaboration among participants in DOE Hydrogen, Fuel Cells, and Infrastructure Technologies Program (HFCIT) cost-shared research directed at distributed bio-liquid reforming. The Working Group includes

217

Synergize fuel and petrochemical processing plans with catalytic reforming  

Science Conference Proceedings (OSTI)

Depending on the market, refiner`s plans to produce clean fuels and higher value petrochemicals will weigh heavily on the catalytic reformer`s flexibility. It seems that as soon as a timely article related to catalytic reforming operations is published, a new {open_quotes}boutique{close_quotes} gasoline fuel specification is slapped on to existing fuel standards, affecting reformer operations and processing objectives. Just as importantly, the petrochemical market (such as aromatics) that refiners are targeting, can be very fickle. That`s why process engineers have endeavored to maintain an awareness of the flexibility that technology suppliers are building into modern catalytic reformers.

NONE

1997-03-01T23:59:59.000Z

218

Effect of reaction pressure on octane number and reformate and hydrogen yields in catalytic reforming  

Science Conference Proceedings (OSTI)

The effect of reaction pressure in catalytic reforming was studied in a pilot reactor with a commercial Pt-Re/Al{sub 2}O{sub 3} reforming catalyst and a hydrotreated naphtha from a North Sea crude. Reformate and hydrogen yields, research octane numbers (RON), and reformate composition at reactor pressures in the range of 12--25 bar were measured as a function of temperature in the range of 95--105 RON. Reformate and hydrogen yields increased as the pressure range. For the lower reaction pressures the hydrogen yields increased with increasing severity, but for the higher pressures the hydrogen yields started to decline above certain severities. RON was linearly dependent on the concentration of aromatics in the reformate, although the selectivity toward aromatics depends on both pressure and temperature. Less hydro dealkylation of C{sub 8} and heavier aromatics to benzene and toluene resulted in a shift toward xylenes and heavier aromatic components when pressure was lowered. Variations in the degree of paraffin isomerization did not influence RON significantly at those severities.

Moljord, K.; Hellenes, H.G.; Hoff, A.; Tanem, I. [SINTEF Applied Chemistry, Trondheim (Norway); Grande, K. [Statoil Research Centre, Trondheim (Norway); Holmen, A. [Univ. of Trondheim (Norway). Dept. Industrial Chemistry

1996-01-01T23:59:59.000Z

219

Thermal treatment wall  

DOE Patents (OSTI)

A thermal treatment wall emplaced to perform in-situ destruction of contaminants in groundwater. Thermal destruction of specific contaminants occurs by hydrous pyrolysis/oxidation at temperatures achievable by existing thermal remediation techniques (electrical heating or steam injection) in the presence of oxygen or soil mineral oxidants, such as MnO.sub.2. The thermal treatment wall can be installed in a variety of configurations depending on the specific objectives, and can be used for groundwater cleanup, wherein in-situ destruction of contaminants is carried out rather than extracting contaminated fluids to the surface, where they are to be cleaned. In addition, the thermal treatment wall can be used for both plume interdiction and near-wellhead in-situ groundwater treatment. Thus, this technique can be utilized for a variety of groundwater contamination problems.

Aines, Roger D. (Livermore, CA); Newmark, Robin L. (Livermore, CA); Knauss, Kevin G. (Livermore, CA)

2000-01-01T23:59:59.000Z

220

How Energy Efficiency is "Lighting Up" the Streets of Philadelphia |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

How Energy Efficiency is "Lighting Up" the Streets of Philadelphia How Energy Efficiency is "Lighting Up" the Streets of Philadelphia How Energy Efficiency is "Lighting Up" the Streets of Philadelphia April 6, 2011 - 11:01am Addthis Andy Oare Andy Oare Former New Media Strategist, Office of Public Affairs What does this project do? Philadelphia Streets Department converting 58,000 yellow and green traffic signals to LED's. President Obama has made building a secure, prosperous energy future a top priority. Last week, he outlined a plan to strengthen energy security in a speech at Georgetown University. Then on Friday, he traveled to a UPS shipping facility in Landover, Maryland to announce a major milestone for the "National Clean Fleet Partnership": Five of the largest domestic shipping companies have made commitments to reduce gasoline use in their

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


221

Midtropospheric Anticyclonic Vortex Street Associated with a Cloud Band near a Cold Front  

Science Conference Proceedings (OSTI)

The characteristics and formation mechanism of an anticyclonic vortex street of meso-? scale, which appeared near a cold front around the Ryukyu Islands, Japan, on 11 April 1995, were examined by an analysis of observational data, a numerical ...

Eizi Toyoda; Hiroshi Niino; Kazuhisa Tsuboki; Ryuji Kimura; Masanori Yoshizaki

1999-08-01T23:59:59.000Z

222

DOE - Office of Legacy Management -- Utica Street Warehouse - NY 0-23  

Office of Legacy Management (LM)

Street Warehouse - NY 0-23 Street Warehouse - NY 0-23 FUSRAP Considered Sites Site: UTICA STREET WAREHOUSE (NY.0-23) Eliminated from consideration under FUSRAP Designated Name: Not Designated Alternate Name: None Location: 240 West Utica Street , Buffalo , New York NY.0-23-2 Evaluation Year: 1987 NY.0-23-1 Site Operations: Stored and rebarrelled uranium process residues from operations at Linde. NY.0-23-3 Site Disposition: Eliminated - Original building demolished. Current land use - Parking facility. Potential for residual radioactive contamination considered remote. NY.0-23-1 Radioactive Materials Handled: Yes NY.0-23-1 Primary Radioactive Materials Handled: Natural Uranium Process Residues NY.0-23-1 Radiological Survey(s): None Indicated NY.0-23-1 Site Status: Eliminated from consideration under FUSRAP NY.0-23-1

223

A Numerical Study of the Development of Claud-Street Spacing  

Science Conference Proceedings (OSTI)

Two-dimensional numerical computations of the developing boundary layer with a positive surface heat flux are presented. The model incorporates moisture phase-change effects; we are particularly interested in the cloud-street formation. The ...

R. I. Sykes; W. S. Lewellen; D. S. Henn

1988-09-01T23:59:59.000Z

224

A Numerical Study of Flow and Pollutant Dispersion Characteristics in Urban Street Canyons  

Science Conference Proceedings (OSTI)

The flow and pollutant dispersion in urban street canyons are investigated using a two-dimensional numerical model with the k–? turbulent closure scheme. It is shown that the flow field is characterized mainly by the number and intensity of ...

Jong-Jin Baik; Jae-Jin Kim

1999-11-01T23:59:59.000Z

225

Woodward Avenue, Detroit : a pedestrian zone for a changing downtown retail street  

E-Print Network (OSTI)

The thesis studies the changing direction of Detroit's central downtown shopping street, Woodward Avenue. During the last two decades, Woodward Avenue has lost most of its retail market to suburban shopping centers. The ...

Lewis, Philip Strickland

1981-01-01T23:59:59.000Z

226

FROM COUNTERPUBLICS TO COUNTERSPACES: Livable city advocates' efforts to reshape cities through carfree-streets events  

E-Print Network (OSTI)

left turns to enter the gas station located at the corner ofspill in April 2010, the gas station on Fell Street, which11, 2010 in front of the gas station and they continued for

Morhayim, Lusi

2012-01-01T23:59:59.000Z

227

IntenCity - 2 Solid State Outdoor Luminaire SL-3200 High Output LED Street Light  

Science Conference Proceedings (OSTI)

The product under assessment is an advanced lighting technology8212a solid state outdoor luminarie light emitting diode (LED) street lighting system designed to provide various levels of direct white light.

2008-06-12T23:59:59.000Z

228

Sociology, Street-Level Bureaucracy, and the Management of the Public Sector  

E-Print Network (OSTI)

This article extends the concept of street-level bureaucracy to address the problem of the inflexibility and rigidity of governmental rules and regulations, a problem at the heart of the standard economic argument against ...

Piore, Michael J.

229

A right to vend : new policy framework for fostering street based entrepreneurs in New York City  

E-Print Network (OSTI)

Street vending remains one of the most highly regulated and least understood activities in New York City. The current regulatory framework is overly confusing and complex, leaving policy decisions about who gets to vend ...

Liu, Ya-Ting, M.C.P. Massachusetts Institute of Technology

2007-01-01T23:59:59.000Z

230

The Recovery Act is "Lighting Up" the streets of Philadelphia | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The Recovery Act is "Lighting Up" the streets of Philadelphia The Recovery Act is "Lighting Up" the streets of Philadelphia The Recovery Act is "Lighting Up" the streets of Philadelphia Addthis Description The Philadelphia Streets Department is converting 58,000 yellow and green traffic signals and will replace approximately 27,000 red LED lights that have come to the end of their useful life. The project will use approximately $3 million in EECBG funds, matched with $3 million in PECO funding, and will save the city approximately $1 million in electric costs each year. Speakers Micheal Nutter, Toby Russel, Katherine Gajewski, DeLain Best, Duration 2:23 Topic Commercial Lighting Energy Sector Jobs Grants Credit Energy Department Video MAYOR MICHAEL NUTTER (D-PA): We're here to announce a partnership among

231

Recovery Act is "Lighting Up" the Streets of Philadelphia | Department of  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

is "Lighting Up" the Streets of Philadelphia is "Lighting Up" the Streets of Philadelphia Recovery Act is "Lighting Up" the Streets of Philadelphia September 27, 2010 - 5:27pm Addthis Andy Oare Andy Oare Former New Media Strategist, Office of Public Affairs The Philadelphia Streets Department is converting 58,000 yellow and green traffic signals and will replace approximately 27,000 red LED lights that have come to the end of their useful life. The project will use approximately $3 million in Energy Efficiency Conservation Block Grant funds, matched with $3 million in PECO funding, and will save the city approximately $1 million in electric costs each year. The program is part of the larger Greenworks Philadelphia project which commits the city to pursue 15 targets by the year 2015, including:

232

How Energy Efficiency is "Lighting Up" the Streets of Philadelphia |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Energy Efficiency is "Lighting Up" the Streets of Philadelphia Energy Efficiency is "Lighting Up" the Streets of Philadelphia How Energy Efficiency is "Lighting Up" the Streets of Philadelphia April 6, 2011 - 11:01am Addthis Andy Oare Andy Oare Former New Media Strategist, Office of Public Affairs What does this project do? Philadelphia Streets Department converting 58,000 yellow and green traffic signals to LED's. President Obama has made building a secure, prosperous energy future a top priority. Last week, he outlined a plan to strengthen energy security in a speech at Georgetown University. Then on Friday, he traveled to a UPS shipping facility in Landover, Maryland to announce a major milestone for the "National Clean Fleet Partnership": Five of the largest domestic shipping companies have made commitments to reduce gasoline use in their

233

BNL | Joseph S. Wall  

NLE Websites -- All DOE Office Websites (Extended Search)

Joseph S. Wall Joseph S. Wall Emeritus Research Interests Mass mapping of unstained biological molecules with the scanning transmission electron microscope (STEM), particularly assemblies of complexes from subunits of known size and shape. Examples include: Alzheimer's filaments, viral capsids, annelid hemoglobins, hemocyanins, proteases, chaperonins, microtubule proteins, prions and various nucleic acid-protein complexes. Another research area is instrument development involving design and construction of an instrument for low-temperture, energy loss spectroscopy, and elemental mapping at low dose. This is being used to map phosphorus in nucleic acid-protein complexes, phosphorylated proteins and phospholipid structures. He also is director of the Scanning Transmission Electron Microscope STEM

234

Comparing Light-Emitting Diode (LED) Street and Area Lighting to Traditional Lighting Technologies  

Science Conference Proceedings (OSTI)

Manufacturing advances have now made the use of light-emitting diode (LED) technology practical for street and area lighting. To better understand the application, the Electric Power Research Institute (EPRI) teamed with Southern Company and Alabama Power to install LED street lights at a demonstration site and measure the performance. The data showed several disadvantages such as a lower efficacy compared to traditional technology and lower immunity to electrical disturbances, but advantages in energy s...

2012-04-20T23:59:59.000Z

235

Comparing Light-Emitting Diode (LED) Street and Area Lighting to Traditional Lighting Technologies  

Science Conference Proceedings (OSTI)

Manufacturing advances have now made the use of light-emitting diode (LED) technology practical for street and area lighting. To better understand the application, the Electric Power Research Institute (EPRI) teamed with Southern Company and Gulf Power to install LED street lights at a demonstration site and measure their performance. The data showed several disadvantages for the LED lights, such as a lower efficacy compared to traditional technology and lower immunity to electrical disturbances, but an ...

2012-04-06T23:59:59.000Z

236

Autothermal reforming catalyst having perovskite structure  

DOE Patents (OSTI)

The invention addressed two critical issues in fuel processing for fuel cell application, i.e. catalyst cost and operating stability. The existing state-of-the-art fuel reforming catalyst uses Rh and platinum supported over refractory oxide which add significant cost to the fuel cell system. Supported metals agglomerate under elevated temperature during reforming and decrease the catalyst activity. The catalyst is a perovskite oxide or a Ruddlesden-Popper type oxide containing rare-earth elements, catalytically active firs row transition metal elements, and stabilizing elements, such that the catalyst is a single phase in high temperature oxidizing conditions and maintains a primarily perovskite or Ruddlesden-Popper structure under high temperature reducing conditions. The catalyst can also contain alkaline earth dopants, which enhance the catalytic activity of the catalyst, but do not compromise the stability of the perovskite structure.

Krumpel, Michael (Naperville, IL); Liu, Di-Jia (Naperville, IL)

2009-03-24T23:59:59.000Z

237

Hydrocarbon Reformers for Fuel Cell Systems  

Science Conference Proceedings (OSTI)

Several new or emerging technologies are vying to compete in the distributed resources market; notably, fuel cells and microturbines. Fuel cells represent an idealized power generation technology with tremendous long-term promise. As a hydrogen-fueled system, however, fuel cells need either a hydrogen fuel supply infrastructure or fuel processing (reforming and clean-up) technology to convert conventional fossil fuels to a hydrogen-rich energy source. This report provides an overview of fuel processing t...

2000-11-30T23:59:59.000Z

238

Purification of reformer streams by catalytic hydrogenation  

Science Conference Proceedings (OSTI)

Catalytic Reforming is one of the most important processes to produce high grade motor gasolines. Feedstocks are mainly gasoline and naphtha streams from the crude oil distillation boiling in the range of 212 F to 350 F. By catalytic reforming the octane number of these gasoline components is increased from 40--60 RON to 95--100 RON. Besides isomerization and dehydrocyclization reactions mainly formation of aromatics by dehydrogenation of naphthenes occur. Thus, catalytic reformers within refineries are an important source of BTX--aromatics (benzene, toluene, xylenes). Frequently, high purity aromatics are recovered from these streams using modern extractive distillation or liquid extraction processes, e.g. the Krupp-Koppers MORPHYLANE{reg_sign} process. Aromatics product specifications, notably bromine index and acid wash color, have obligated producers to utilize clay treatment to remove trace impurities of diolefins and/or olefins. The conventional clay treatment is a multiple vessel batch process which periodically requires disposal of the spent clay in a suitable environmental manner. BASF, in close cooperation with Krupp-Koppers, has developed a continuous Selective Catalytic Hydrogenation Process (SCHP) as an alternative to clay treatment which is very efficient, cost effective and environmentally compatible. In the following the main process aspects including the process scheme catalyst and operating conditions is described.

Polanek, P.J. [BASF Corp., Geismar, LA (United States); Hooper, H.M. [Krupp Wilputte Corp., Bridgeville, PA (United States); Mueller, J.; Walter, M. [BASF AG, Ludwigshafen (Germany); Emmrich, G. [Krupp Koppers GmbH, Essen (Germany)

1996-12-01T23:59:59.000Z

239

IFP solutions for revamping catalytic reforming units  

Science Conference Proceedings (OSTI)

The decision-making process for the refiner considering a revamp of a catalytic reforming unit comprises many factors. These may be grouped in two broad areas: technical and economic. This paper presents the results of a study performed by IFP that illustrates catalytic reforming unit revamp options. Three IFP processes are described and operating conditions, expected yields, and economic data are presented. The following options are discussed: base case Conventional, fixed-bed, semi-regenerative catalytic reformer; Case 1--revamp using IFP Dualforming technology; Case 2--revamp using IFP Dualforming Plus technology; and Case 3--revamp to IFP Octanizing technology. The study illustrates various options for the refiner to balance unit performance improvements with equipment, site, and economic constraints. The study was performed assuming design feedrate of 98.2 tons/hour (20,000 BPSD) in all cases. Because of the increased need for octane in many refineries, the study assumed that operating severity was set at a design value of 100 research octane number clear (RON). In all of the cases in this study, it was assumed that the existing recycle compressor was reused. Operating pressure differences between the cases is discussed separately. Also, in all cases, a booster compressor was included in order to return export hydrogen pressure to that of the conventional unit.

Gendler, J.L. [HRI, Inc., Princeton, NJ (United States); Domergue, B.; Mank, L. [Inst. Francais du Petrole, Rueil Malmaison (France)

1996-12-01T23:59:59.000Z

240

Methods of Reforming Hydrocarbon Fuels Using Hexaaluminate Catalysts  

NLE Websites -- All DOE Office Websites (Extended Search)

of Reforming Hydrocarbon Fuels Using of Reforming Hydrocarbon Fuels Using Hexaaluminate Catalysts Contact NETL Technology Transfer Group techtransfer@netl.doe.gov May 2012 Opportunity Research is currently active on the technology "Methods of Reforming Hydrocarbon Fuels Using Hexaaluminate Catalysts." The technology is available for licensing and/or further collaborative research from the U.S. Department of Energy's National Energy Technology Laboratory. Overview This invention discloses a method to reform hydrocarbon fuels using hexa- aluminate catalysts. In general, the method successfully disrupts the forma- tion of carbon that leads to the deactivation of the catalyst, a key element in the reforming of hydrocarbon fuels. When researchers are designing catalysts to reform hydrocarbon fuels, one

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


241

Partial oxidation fuel reforming for automotive power systems.  

DOE Green Energy (OSTI)

For widespread use of fuel cells to power automobiles in the near future, it is necessary to convert gasoline or other transportation fuels to hydrogen on-board the vehicle. Partial oxidation reforming is particularly suited to this application as it eliminates the need for heat exchange at high temperatures. Such reformers offer rapid start and good dynamic performance. Lowering the temperature of the partial oxidation process, which requires the development of a suitable catalyst, can increase the reforming efficiency. Catalytic partial oxidation (or autothermal) reformers and non-catalytic partial oxidation reformers developed by various organizations are presently undergoing testing and demonstration. This paper summarizes the process chemistries as well as recent test data from several different reformers operating on gasoline, methanol, and other fuels.

Ahmed, S.; Chalk, S.; Krumpelt, M.; Kumar, R.; Milliken, J.

1999-09-07T23:59:59.000Z

242

High-R Walls for Remodeling: Wall Cavity Moisture Monitoring  

Science Conference Proceedings (OSTI)

The focus of the study is on the performance of wall systems, and in particular, the moisture characteristics inside the wall cavity and in the wood sheathing. Furthermore, while this research will initially address new home construction, the goal is to address potential moisture issues in wall cavities of existing homes when insulation and air sealing improvements are made.

Wiehagen, J.; Kochkin, V.

2012-12-01T23:59:59.000Z

243

Will electricity market reform likely reduce retail rates?  

Science Conference Proceedings (OSTI)

To win public support, proponents for electricity market reform to introduce competition often promise that the post-reform retail rates will be lower than the average embedded cost rates that would have prevailed under the status quo of a regulated monopoly. A simple economic analysis shows that such a promise is unlikely to occur without the critical assumption that the post-reform market has marginal costs below average costs. (author)

Woo, C.K.; Zarnikau, Jay

2009-03-15T23:59:59.000Z

244

Catalysts for steam reforming of Ethanol in a catalytic wall reactor.  

E-Print Network (OSTI)

??La energía se ha convertido en una necesidad vital para garantizar el desarrollo de las sociedades modernas. Entre las diferentes posibles alternativas para producir energía,… (more)

Torres Rivero, José Antonio

2008-01-01T23:59:59.000Z

245

Wall conditions in ORMAK  

SciTech Connect

From surface effects in controlled thermonuclear fusion devices and reactors meeting; Argonne, Illnois, USA (10 Jan 1974). ORMAK is a diffuse toroidal pinch with typical plasma currents of 100 kA, electron temperatures of 800 eV, and ion temperatures of 300 eV. The walls of the plasma region are made of stainless steel coated with an intermediate layer of platinum 0.05 mu thick and an outer 1 to 2 mu layer of gold. Tests with an Ion Microprobe Mass Analyzer have shown that the platinum acts to decrease diffusion of impurities from the stalnless steel to the surface. Gold was chosen to inhibit the surface chemical adsorption of gases. Studies with a movable limiter indicate that electron energy is lost at the plasma edge mainly via line radiation and cooling on ions, while ions are lost from the plasma by charge exchange. Thus the walls are bombarded by energetic neutrals, line radiation and, in addition, bremsstrahlung x-rays. The flux of energetic neutrals is measured by a charge exchange analyzer. Wall bombardment by such neutrals should cause sputtering, and gold has been observed spectroscopically near the limiter, increasing with time during a shot, However, analysis of impurities coated on a window by the discharge indicated very little gold sputtering and re-deposition. To measure the sputterirg rate, a wall sample was coated with 105 A of radioactive gold and bombarded with neutrals from ORMAK during a day's run. No measurable sputtering was found within the counting statistics of the measurement, but surface carbon contamination of the sample prevented any final conclusions. (auth)

Colchin, R.J.; Berry, L.A.; Haste, G.R.; Kelley, G.G.; Lyon, J.F.; McNally, J.R.; Murakami, M.; Neidigh, R.V.; Simpkins, J.E.; Wing, W.R.

1972-01-01T23:59:59.000Z

246

Microsoft Word - Poster Abstract_2010_NETL_ Oxide-Based Reforming...  

NLE Websites -- All DOE Office Websites (Extended Search)

Structured Oxide - Based Reforming Catalyst Development U.S. Dept of Energy, National Energy Technology Laboratory, Morgantown, WV 26507 Dushyant Shekhawat Dushyant.Shekhawat@NETL....

247

Compatibility of selected ceramics with steam-methane reformer environments  

DOE Green Energy (OSTI)

Conventional steam reforming of methane to synthesis gas (CO and H{sub 2}) hasa conversion efficiency of about 85%. Replacement of metal tubes in the reformer with ceramic tubes offers the potential for operation at temperatures high enough to increase the efficiency to 98-99%. However, the two candidate ceramic materials being given strongest consideration, sintered alpha Si carbide and Si carbide particulate-strengthened alumina, have been shown to react with components of the reformer environment. Extent of degradation as a function of steam partial pressure and exposure time has been studied, and results suggest limits under which these structural ceramics can be used in advanced steam-methane reformers.

Keiser, J.R.; Howell, M. [Oak Ridge National Lab., TN (United States); Williams, J.J.; Rosenberg, R.A. [Stone and Webster Engineering Corp., Boston, MA (United States)

1996-04-01T23:59:59.000Z

248

Thermodynamic and Experimental Study on the Steam Reforming ...  

Science Conference Proceedings (OSTI)

For improving hydrogen yield, a new system for steam reforming of bio-oil with site ... Kinetic Modeling Study of Oxy-methane Combustion at Ordinary Pressure.

249

Women and the reform of the welfare system: An introduction  

Science Conference Proceedings (OSTI)

This special issue of Gender Issues, one of a three-part series, examines the welfare reform measures initiated a decade ago and their consequences for ...

250

Kinetics of Supercritical Water Reformation of Ethanol to H  

Science Conference Proceedings (OSTI)

Sep 16, 2007 ... Description Kinetics of the supercritical water reformation of ethanol was experimentally studied in a tubular reactor made of Inconel 625 alloy.

251

Catalytic reforming boosts octane for gasoline blending - Today in ...  

U.S. Energy Information Administration (EIA)

Because reformate contains significant amounts of benzene, toluene, and xylene, it also is an important source of feedstock for the petrochemical industry.

252

New process model proves accurate in tests on catalytic reformer  

Science Conference Proceedings (OSTI)

A mathematical model has been devised to represent the process that takes place in a fixed-bed, tubular, adiabatic catalytic reforming reactor. Since its development, the model has been applied to the simulation of a commercial semiregenerative reformer. The development of mass and energy balances for this reformer led to a model that predicts both concentration and temperature profiles along the reactor. A comparison of the model's results with experimental data illustrates its accuracy at predicting product profiles. Simple steps show how the model can be applied to simulate any fixed-bed catalytic reformer.

Aguilar-Rodriguez, E.; Ancheyta-Juarez, J. (Inst. Mexicano del Petroleo, Mexico City (Mexico))

1994-07-25T23:59:59.000Z

253

Bumper wall for plasma device  

DOE Patents (OSTI)

Operation of a plasma device such as a reactor for controlled thermonuclear fusion is facilitated by an improved bumper wall enclosing the plasma to smooth the flow of energy from the plasma as the energy impinges upon the bumper wall. The bumper wall is flexible to withstand unequal and severe thermal shocks and it is readily replaced at less expense than the cost of replacing structural material in the first wall and blanket that surround it.

Coultas, Thomas A. (Hinsdale, IL)

1977-01-01T23:59:59.000Z

254

Process for removal of polynuclear aromatics from a hydrocarbon in an endothermic reformer reaction system  

Science Conference Proceedings (OSTI)

A process is described for reforming a hydrocarbon in a multi-stage endothermic reforming series of catalytic reforming reactors where the hydrocarbon is passed through the series of catalytic reforming reactors to form a reformate. The hydrocarbon is heated prior to entry to the next catalytic reforming reactor in the series, which process comprises contact of the hydrocarbon intermediate from the series of catalytic reforming reactors containing reforming catalyst with a polynuclear aromatic adsorbent to adsorb at least a portion of the polynuclear aromatic content from the hydrocarbon prior to entry to each of the next catalytic reforming reactor in the series and recovering a reformate from the last catalytic reforming reactor in the series, the recovered reformate having a reduced content of polynuclear aromatics.

Ngan, D.Y.

1989-02-14T23:59:59.000Z

255

"If we own the story, we own the place": Cultural Heritage, Historic Preservation, and Gentrification on U Street.  

E-Print Network (OSTI)

??This thesis investigates the roles of cultural heritage and historic preservation in the gentrification of the Greater U Street neighborhood in Washington, D.C. Its larger… (more)

Frank, Stephanie

2005-01-01T23:59:59.000Z

256

Vector-field domain walls  

Science Conference Proceedings (OSTI)

We argue that spontaneous Lorentz violation may generally lead to metastable domain walls related to the simultaneous violation of some accompanying discrete symmetries. Remarkably, such domain-wall solutions exist for spacelike Lorentz violation and do not exist for the timelike violation. Because a preferred space direction is spontaneously induced, these domain walls have no planar symmetry and produce a peculiar static gravitational field at small distances, while their long-distance gravity appears the same as for regular scalar-field walls. Some possible applications of vector-field domain walls are briefly discussed.

Chkareuli, J. L. [E. Andronikashvili Institute of Physics, 0177 Tbilisi, Georgia (United States); I. Chavchavadze State University, 0162 Tbilisi (Georgia); Kobakhidze, Archil [E. Andronikashvili Institute of Physics, 0177 Tbilisi (Georgia); School of Physics, University of Melbourne, Victoria 3010 (Australia); Volkas, Raymond R. [School of Physics, University of Melbourne, Victoria 3010 (Australia)

2009-09-15T23:59:59.000Z

257

EA-1741: Seattle Steam Company Combined Heat and Power at Post Street in  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

741: Seattle Steam Company Combined Heat and Power at Post 741: Seattle Steam Company Combined Heat and Power at Post Street in Downtown Seattle, Washington EA-1741: Seattle Steam Company Combined Heat and Power at Post Street in Downtown Seattle, Washington Summary This EA evaluates the environmental impacts of a proposal to provide an American Recovery Act and Reinvestment Act of 2009 financial assistance grant to Seattle Steam Company to facilitate the installation of a combined heat and power plant in downtown Seattle, Washington. NOTE: This project has been cancelled. Public Comment Opportunities No public comment opportunities available at this time. Documents Available for Download June 16, 2010 EA-1741: Draft Environmental Assessment Seattle Steam Company Combined Heat and Power at Post Street in Downtown Seattle, Washington (June 2010)

258

Students Earn Street Cred With the EcoCAR Challenge | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Students Earn Street Cred With the EcoCAR Challenge Students Earn Street Cred With the EcoCAR Challenge Students Earn Street Cred With the EcoCAR Challenge Addthis EcoCAR Challenge Finish Line Event 1 of 8 1 of 8 EcoCAR Challenge Finish Line Event 1 of 8 US Department of Energy Secretary Steven Chu talks shop with members of the West Virginia EcoCAR team. Image: Energy Department Image | Photo by Charles Watkins, Contractor EcoCAR Challenge Finish Line Event2 of 8 2 of 8 EcoCAR Challenge Finish Line Event2 of 8 Secretary Steven Chu discusses the EcoCAR Challenge during the 'Finish Line' event held at the US Department of Energy headquarters in Washington, DC. Image: Energy Department Image | Photo by Charles Watkins, Contractor EcoCAR Challenge Finish Line Event 3 of 8 3 of 8 EcoCAR Challenge Finish Line Event 3 of 8

259

NEPA Contracting Reform Guidance (December 1996)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

defining early what contractors should accomplish defining early what contractors should accomplish < establishing contracts ahead of time < minimizing cost while maintaining quality by * maximizing competition and use of incentives * using past performance information in awarding work * managing the NEPA process as a project This guidance provides: < model statements of work < information on contract types and incentives < direction on effective NEPA contract management by the NEPA Document Manager < a system for measuring NEPA process costs < NEPA contractor evaluation procedures < details on the DOE NEPA Web site U.S. Department of Energy, Office of NEPA Policy and Assistance, December 1996 NEPA CONTRACTING REFORM GUIDANCE Table of Contents 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . .

260

Noble metal alkaline zeolites for catalytic reforming  

Science Conference Proceedings (OSTI)

This patent describes a method for producing a noble-metal containing zeolite suitable for catalytic reforming contacting a zeolite selected from alkaline faujasites and L zeolites and zeolites and zeolites isostructural thereto, with a noble-metal compound selected from Pt(acetylacetonate){sub 2} and Pd(acetylacetonate){sub 2} for a effective amount of time to incorporate Pt and/or Pd into the pore surface regions of the zeolite, but not to disperse the Pt and/or Pd throughout the entire zeolite; and calcining the so treated zeolite at a temperature from about 250 {degrees} C, to about 600 {degrees} C for an effective amount of time.

Schweizer, A.E.

1991-02-12T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


261

Computational Model For Transient And Steady State Analysis Of A 1-dimensional Auto-thermal Reformer.  

E-Print Network (OSTI)

??Kim, Daejong This study presents a 1-dimensional mathematical model of steam reformer to be used with high temperature solid oxide fuel cell (SOFC). Steam reforming… (more)

Honavara-Prasad, Srikanth

2011-01-01T23:59:59.000Z

262

Sequencing in telecommunications reform: A review of the Turkish case  

Science Conference Proceedings (OSTI)

This paper reviews the Turkish case of telecommunications reform with reference to the evidence from the sequencing literature. Turkey's progress is in line with the proper sequencing of reform suggested by the literature. Accordingly, Turkey has pursued ... Keywords: Industrial policy, Privatisation, Regulation, Telecommunications

Necmiddin Bagdadioglu; Murat Cetinkaya

2010-12-01T23:59:59.000Z

263

Steam reforming of fuel to hydrogen in fuel cells  

DOE Patents (OSTI)

A fuel cell capable of utilizing a hydrocarbon such as methane as fuel and having an internal dual catalyst system within the anode zone, the dual catalyst system including an anode catalyst supporting and in heat conducting relationship with a reforming catalyst with heat for the reforming reaction being supplied by the reaction at the anode catalyst.

Fraioli, Anthony V. (Hawthorne Woods, IL); Young, John E. (Woodridge, IL)

1984-01-01T23:59:59.000Z

264

Steam reforming of fuel to hydrogen in fuel cell  

DOE Patents (OSTI)

A fuel cell is described capable of utilizing a hydrocarbon such as methane as fuel and having an internal dual catalyst system within the anode zone, the dual catalyst system including an anode catalyst supporting and in heat conducting relationship with a reforming catalyst with heat for the reforming reaction being supplied by the reaction at the anode catalyst.

Young, J.E.; Fraioli, A.V.

1983-07-13T23:59:59.000Z

265

Electricity Reform Abroad and U.S. Investment  

Reports and Publications (EIA)

Reviews and analyzes the recent electricity reforms in Argentina, Australia, and the United Kingdom in an attempt to better understand how different models of privatization and reform have worked in practice. This report also analyzes the motivations of the U.S. companies who have invested in the electricity industries of Argentina, Australia, and the UK.

Kevin Lillis

1997-09-01T23:59:59.000Z

266

Reforming naphtha with boron-containing large-pore zeolites  

Science Conference Proceedings (OSTI)

This patent describes a catalytic reforming process. It comprises contacting a hydrocarbonaceous feedstream under catalytic reforming conditions with a composition comprising larger-pore borosilicate zeolites having a pore size greater than 6 and less than 8 angstroms containing less that 1000 parts per million aluminum.

Zones, S.I.; Holtermann, D.L.; Rainis, A.

1992-05-19T23:59:59.000Z

267

Thick planar domain wall: its thin wall limit and dynamics  

E-Print Network (OSTI)

We consider a planar gravitating thick domain wall of the $\\lambda \\phi^4$ theory as a spacetime with finite thickness glued to two vacuum spacetimes on each side of it. Darmois junction conditions written on the boundaries of the thick wall with the embedding spacetimes reproduce the Israel junction condition across the wall in the limit of infinitesimal thickness. The thick planar domain wall located at a fixed position is then transformed to a new coordinate system in which its dynamics can be formulated. It is shown that the wall's core expands as if it were a thin wall. The thickness in the new coordinates is not constant anymore and its time dependence is given.

S. Ghassemi; S. Khakshournia; R. Mansouri

2006-09-28T23:59:59.000Z

268

Technology Maturation Plan (TMP) Fluidized Bed Steam Reforming (FBSR)  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Maturation Plan (TMP) Fluidized Bed Steam Reforming Maturation Plan (TMP) Fluidized Bed Steam Reforming (FBSR) Technology for Tank 48H Treatment Project (TTP) Technology Maturation Plan (TMP) Fluidized Bed Steam Reforming (FBSR) Technology for Tank 48H Treatment Project (TTP) This assessment determines the technology maturity level of the candidate Tank 48H treatment technologies that are being considered for implementation at DOE's SRS - specifically Fluidized Bed Steam Reformer System. Technology Maturation Plan (TMP) Fluidized Bed Steam Reforming (FBSR) Technology for Tank 48H Treatment Project (TTP) More Documents & Publications Technology Maturation Plan (TMP) Wet Air Oxidation (WAO) Technology for Tank 48H Treatment Project (TTP) SRS Tank 48H Waste Treatment Project Technology Readiness Assessment

269

Reforming Power Markets in Developing Countries | Open Energy Information  

Open Energy Info (EERE)

Reforming Power Markets in Developing Countries Reforming Power Markets in Developing Countries Jump to: navigation, search Tool Summary LAUNCH TOOL Name: Reforming Power Markets in Developing Countries Agency/Company /Organization: World Bank Sector: Energy Focus Area: Conventional Energy, Renewable Energy Topics: Policies/deployment programs Resource Type: Publications, Lessons learned/best practices Website: siteresources.worldbank.org/INTENERGY/Resources/Energy19.pdf References: Reforming Power Markets in Developing Countries [1] Summary "This paper complements the World Bank's Operational Guidance Note by compiling lessons of this experience that help in applying the Note's guidance. These lessons are taken from the rapidly growing literature on power market reform in developing countries. They cover the range of issues

270

Electricity Reform in Chile. Lessons for Developing Countries  

E-Print Network (OSTI)

Chile was the first country in the world to implement a comprehensive reform of its electricity sector in the recent period. Among developing countries only Argentina has had a comparably comprehensive and successful reform. This paper traces the history of the Chilean reform, which began in 1982, and assesses its progress and its lessons. We conclude that the reform has been very successful. We suggest lessons for the generation, transmission and distribution sectors, as well as the economic regulation of electricity and the general institutional environment favourable to reform. We note that while the initial market structure and regulatory arrangements did give rise to certain problems, the overall experience argues strongly for the private ownership and operation of the electricity industry.

Michael Pollitt

2004-01-01T23:59:59.000Z

271

Removal of sulfur from recycle gas streams in catalytic reforming  

Science Conference Proceedings (OSTI)

This patent describes improvement in a process for catalytically reforming a hydrocarbonaceous feedstock boiling in the gasoline range, wherein the reforming is conducted in the presence of hydrogen in a reforming process unit under reforming conditions, the process unit comprised of serially connected reactors, each of the reactors containing a reforming catalyst, and which process unit also includes a regeneration circuit for regenerating the catalyst after it becomes coked, the regeneration comprising treatment with a sulfur containing gas, and which process unit also includes a gas/liquid separator wherein a portion of the gas is recycled and the remaining portion is collected as make-gas. The improvement comprises using a sulfur trap, containing a catalyst comprised of about 10 to about 70 wt. % nickel dispersed on a support, between the gas/liquid separator and the first reactor.

Boyle, J.P.

1991-08-27T23:59:59.000Z

272

Advances in the chemistry of catalytic reforming of naphtha  

Science Conference Proceedings (OSTI)

Catalytic reforming of naphtha remains the key process for production of high octane gasoline and aromatics (BTX) which are used as petrochemicals feedstocks. The increased demand for these products has led refiners to investigate ways for improving the performance of the reforming process and its catalysts. Moreover, in order to comply with environmental restrictions, the reduction in lead content would require further increase in the reformate octane number. In response to these requirements, refiners and catalyst manufacturers are examining the role of the catalysts in improving the selectivity to aromatics and in octane enhancement. By understanding the chemistry and the mechanism of the reforming process, higher performance catalysts with longer life on stream and lower cost can be developed. This review covers recent developments in reforming catalysts, process reaction chemistry and mechanism. It also highlights prospective areas of research.

Anabtawi, J.A.; Redwan, D.S.; Al-Jarallah, A.M.; Aitani, A.M. (Petroleum and Gas Technology Div., Research Inst., King Fahd Univ. of Petroleum and Minerals, Dhahran (SA))

1991-01-01T23:59:59.000Z

273

Regulatory and Financial Reform of Federal Research Policy: Recommendations  

NLE Websites -- All DOE Office Websites (Extended Search)

and Financial Reform of Federal Research Policy: and Financial Reform of Federal Research Policy: Recommendations to the NRC Committee on Research Universities Regulatory and Financial Reform of Federal Research Policy: Recommendations to the NRC Committee on Research Universities At the request of the National Research Council (NRC) Committee on Research Universities, the Council on Governmental Relations (COGR), the Association of American Universities (AAU), and the Association of Public and Land-grant Universities (APLU) have assembled a set of ten recommendations for regulatory reform that would improve research universities' ability to carry out their missions without requiring a significant financial investment by the Federal government. Regulatory and Financial Reform of Federal Research Policy: Recommendations

274

Process Reform, Security and Suitability - December 17, 2008 | Department  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Process Reform, Security and Suitability - December 17, 2008 Process Reform, Security and Suitability - December 17, 2008 Process Reform, Security and Suitability - December 17, 2008 December 17, 2008 This is to report on the progress made to improve the timeliness and effectiveness of our hiring and clearing decisions and the specific plan to reform the process further, in accordance with our initial proposals made in April ofthis year. In response to significant, continuing security clearance timeliness concerns, Congress called for improvements and established specific timeliness goals as part of the Intelligence Reform and Terrorism Prevention Act of 2004 (IRTPA). Since the enactment of IRTPA, average timeliness for 90 percent of all clearance determinations reported has been substantially improved, from 265 days (in 2005) to 82 days (4th Quarter,

275

TWR Bench-Scale Steam Reforming Demonstration  

SciTech Connect

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by ThermoChem Waste Remediation, LLC, (TWR) for treatment of SBW into a ''road ready'' waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). TWR is the licensee of Manufacturing Technology Conservation International (MTCI) steam-reforming technology in the field of radioactive waste treatment. A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrate residues were about 400 ppm in the product and NOx destruction exceeded 86%. The demonstration was successful.

Marshall, D.W.; Soelberg, N.R.

2003-05-21T23:59:59.000Z

276

TWR Bench-Scale Steam Reforming Demonstration  

SciTech Connect

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by ThermoChem Waste Remediation, LLC, (TWR) for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). TWR is the licensee of Manufacturing Technology Conservation International (MTCI) steam-reforming technology in the field of radioactive waste treatment. A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrate residues were about 400 ppm in the product and NOx destruction exceeded 86%. The demonstration was successful.

D. W. Marshall; N. R. Soelberg

2003-05-01T23:59:59.000Z

277

Home Production and Social Security Reform ?  

E-Print Network (OSTI)

This paper incorporates home production into a dynamic general equilibrium model of overlapping generations with endogenous retirement to study Social Security reforms. As such, the model differentiates both consumption goods and labor effort according to their respective roles in home production and market activities. Using a calibrated model, we conduct a policy experiment where we eliminate the current pay-as-you-go Social Security System and study the steady state impact. We find that the experiment has important implications for labor supply as well as consumption decisions and that these decisions are influenced by the presence of a home production technology. Comparing our economy to a onegood economy without home production, the welfare gains of eliminating Social Security are magnified significantly. We further demonstrate that the qualitative results hold with the less extreme policy reform where we delay the eligible Social Security benefits claimant age by four years. These policy analyses suggest the importance of modeling home production and distinguishing between both time

Michael Dotsey; Wenli Li; Fang Yang

2012-01-01T23:59:59.000Z

278

Flow Patterns at the Ends of a Street Canyon: Measurements from the Joint Urban 2003 Field Experiment  

Science Conference Proceedings (OSTI)

During the Joint Urban 2003 experiment held in Oklahoma City, Oklahoma, an east–west-running street canyon was heavily instrumented with wind sensors. In this paper, the flow patterns at the street canyon ends are investigated by looking at sonic ...

Suhas U. Pol; Michael J. Brown

2008-05-01T23:59:59.000Z

279

UCSC Student Health Services Student Health Insurance Office 1156 High Street Phone: (831) 459-2389  

E-Print Network (OSTI)

UCSC Student Health Services Student Health Insurance Office 1156 High Street Phone: (831) 459 your health plan's customer service number for assistance.** 5. Does your health insurance plan cover conditions? Yes / No Emergency room services? Yes / No Diagnostic services including laboratory tests? Yes

280

Demonstration Assessment of Light-Emitting Diode (LED) Street Lighting Host Site: Lija Loop, Portland, Oregon  

SciTech Connect

This report describes the process and results of a demonstration of solid-state lighting (SSL) technology in a residential street lighting application, under the U.S. Department of Energy GATEWAY Solid-State Lighting Technology Demonstration Program. In this project, eight 100W (nominal) high-pressure sodium cobra head fixtures were replaced with a like number of LED street light luminaires manufactured by Leotek, Inc. The Leotek product achieved an estimated payback in the Lija Loop installation of about 20 years for replacement scenarios and a much shorter 7.6 years for new installations. Much of the associated energy savings (55%) supporting these payback periods, however, were achieved by reducing average horizontal photopic illuminance a similar amount (53%). Examined from a different perspective, the measured performance suggests that the Leotek product is at approximate parity with the HPS cobra head in terms of average delivered photopic illumination for a given power consumption. HPS comprises the second most efficacious street lighting technology available, exceeded only by low pressure sodium (LPS). LPS technology is not considered suitable for most street lighting applications due to its monochromatic spectral output and poor color rendering ability; therefore, this LED product is performing at an efficiency level comparable to its primary competition in this application.

Kinzey, Bruce R.; Myer, Michael

2009-11-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


281

Automated extraction of street-scene objects from mobile lidar point clouds  

Science Conference Proceedings (OSTI)

Mobile laser scanning or lidar is a new and rapid system to capture high-density three-dimensional 3-D point clouds. Automatic data segmentation and feature extraction are the key steps for accurate identification and 3-D reconstruction of street-scene ...

Bisheng Yang; Zheng Wei; Qingquan Li; Jonathan Li

2012-09-01T23:59:59.000Z

282

Oven wall panel construction  

DOE Patents (OSTI)

An oven roof or wall is formed from modular panels, each of which comprises an inner fabric and an outer fabric. Each such fabric is formed with an angle iron framework and somewhat resilient tie-bars or welded at their ends to flanges of the angle irons to maintain the inner and outer frameworks in spaced disposition while minimizing heat transfer by conduction and permitting some degree of relative movement on expansion and contraction of the module components. Suitable thermal insulation is provided within the module. Panels or skins are secured to the fabric frameworks and each such skin is secured to a framework and projects laterally so as slidingly to overlie the adjacent frame member of an adjacent panel in turn to permit relative movement during expansion and contraction.

Ellison, Kenneth (20 Avondale Cres., Markham, CA); Whike, Alan S. (R.R. #1, Caledon East, both of Ontario, CA)

1980-04-22T23:59:59.000Z

283

Hiring Reform Memoranda and Action Plan  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

0585 0585 October 7, 2010 MEMORANDUM FOR HEADS OF ALL DEPARTMENTAL ELEMEI\lTS HUMAI\l RESOURCES DIRECTORS FROM: MICHAELC. KANE~~~ CHIEF HUMAN CAPITAL ~ c· SUBJECT: IMPROVING DOE RECRUITMENT AND HIRING PROCESSES This is a follow-up to the Deputy Secretary's Memorandum dated October 6, 2010 where he communicated the need to implement the Action Plan developed to improve the recruitment and hiring processes throughout the Department. One of the central tenets of the President's reform efforts and the Department's Action Plan is management's commitment and attention to an efficient and effective hiring process that yields quality employees. This was clearly articulated in the President's Memorandum dated May 11, 2010 where he directed that management be held accountable through the performance evaluation system for their role

284

Evaluation of Partial Oxidation Reformer Emissions  

DOE Green Energy (OSTI)

In this study, a gasoline fuel processor and an ethanol fuel processor were operated under conditions simulating both startup and normal operation. Emissions were measured before and after the AGB in order to quantify the effectiveness of the burner catalyst in controlling emissions. The emissions sampling system includes CEM for O2, CO2, CO, NOx, and THC. Also, integrated gas samples are collected in evacuated canisters for hydrocarbon speciation analysis via GC. This analysis yields the concentrations of the hydrocarbon species required for the California NMOG calculation. The PM concentration in the anode burner exhaust was measured through the placement of a filter in the exhaust stream. The emissions from vehicles with fully developed on board reformer systems were estimated.

Unnasch, Stefan; Fable, Scott; Waterland, Larry

2006-01-06T23:59:59.000Z

285

Clean gasoline reforming with superacid catalysts  

DOE Green Energy (OSTI)

The objectives of this project are to: (a) determine if a coal-derived naphtha can be hydrotreated to produce a product with a sufficiently low heteroatom content that can be used for reforming, (b) identify hydrocarbon compounds in the naphtha with concentrations greater than 0.5 wt %, (c) develop a Pt/Al[sub 2]O[sub 3] heavily chlorided catalyst and determine the activity, selectivity and deactivation of this catalyst using model compounds and the hydrotreated naphtha, and (d) develop both a sulfated Pt/ZrO[sub 2] and Fe/Mn/ZrO[sub 2] catalyst formulations and determine the activity, selectivity and deactivation of these catalysts using model compounds and d warranted, the hydrotreated naphtha.

Davis, B.H.

1992-01-01T23:59:59.000Z

286

SOLAR UPGRADE OF METHANE USING DRY REFORMING IN DIRECT CONTACT BUBBLE REACTOR  

E-Print Network (OSTI)

SOLAR UPGRADE OF METHANE USING DRY REFORMING IN DIRECT CONTACT BUBBLE REACTOR Khalid Al-Ali 1 process of a solar reformer of dry methane reforming was proposed to operate in a temperature range of 600:2:2 fulfills our requirements for the direct contact bubble reactor of the solar reformer, in which a CO2-rich

Recanati, Catherine

287

Thermally efficient melting and fuel reforming for glass making  

DOE Patents (OSTI)

An integrated process is described for utilizing waste heat from a glass making furnace. The hot off-gas from the furnace is initially partially cooled, then fed to a reformer. In the reformer, the partially cooled off-gas is further cooled against a hydrocarbon which is thus reformed into a synthesis gas, which is then fed into the glass making furnace as a fuel. The further cooled off-gas is then recycled back to absorb the heat from the hot off-gas to perform the initial cooling. 2 figures.

Chen, M.S.; Painter, C.F.; Pastore, S.P.; Roth, G.S.; Winchester, D.C.

1991-10-15T23:59:59.000Z

288

Lawn chairs in Times Square : an analysis of the Pilot Streets Program and the provisional project approach for New York City's Green Light in Midtown project  

E-Print Network (OSTI)

In 2009 the New York City Department of Transportation (NYC DOT) initiated a Pilot Streets Program that called for the temporary closure of Broadway between 47th and 42nd Streets to all vehicular traffic. With Times Square ...

Taylor, Alexis (Alexis Abreu)

2011-01-01T23:59:59.000Z

289

Moisture Research - Optimizing Wall Assemblies  

SciTech Connect

The Consortium for Advanced Residential Buildings (CARB) evaluated several different configurations of wall assemblies to determine the accuracy of moisture modeling and make recommendations to ensure durable, efficient assemblies. WUFI and THERM were used to model the hygrothermal and heat transfer characteristics of these walls.

Arena, L.; Mantha, P.

2013-05-01T23:59:59.000Z

290

Multi-fuel reformers for fuel cells used in transportation. Multi-fuel reformers: Phase 1 -- Final report  

DOE Green Energy (OSTI)

DOE has established the goal, through the Fuel Cells in Transportation Program, of fostering the rapid development and commercialization of fuel cells as economic competitors for the internal combustion engine. Central to this goal is a safe feasible means of supplying hydrogen of the required purity to the vehicular fuel cell system. Two basic strategies are being considered: (1) on-board fuel processing whereby alternative fuels such as methanol, ethanol or natural gas stored on the vehicle undergo reformation and subsequent processing to produce hydrogen, and (2) on-board storage of pure hydrogen provided by stationary fuel processing plants. This report analyzes fuel processor technologies, types of fuel and fuel cell options for on-board reformation. As the Phase 1 of a multi-phased program to develop a prototype multi-fuel reformer system for a fuel cell powered vehicle, the objective of this program was to evaluate the feasibility of a multi-fuel reformer concept and to select a reforming technology for further development in the Phase 2 program, with the ultimate goal of integration with a DOE-designated fuel cell and vehicle configuration. The basic reformer processes examined in this study included catalytic steam reforming (SR), non-catalytic partial oxidation (POX) and catalytic partial oxidation (also known as Autothermal Reforming, or ATR). Fuels under consideration in this study included methanol, ethanol, and natural gas. A systematic evaluation of reforming technologies, fuels, and transportation fuel cell applications was conducted for the purpose of selecting a suitable multi-fuel processor for further development and demonstration in a transportation application.

Not Available

1994-05-01T23:59:59.000Z

291

An Innovative Injection and Mixing System for Diesel Fuel Reforming  

DOE Green Energy (OSTI)

This project focused on fuel stream preparation improvements prior to injection into a solid oxide fuel cell reformer. Each milestone and the results from each milestone are discussed in detail in this report. The first two milestones were the creation of a coking formation test rig and various testing performed on this rig. Initial tests indicated that three anti-carbon coatings showed improvement over an uncoated (bare metal) baseline. However, in follow-up 70 hour tests of the down selected coatings, Scanning Electron Microscope (SEM) analysis revealed that no carbon was generated on the test specimens. These follow-up tests were intended to enable a down selection to a single best anti-carbon coating. Without the formation of carbon it was impossible to draw conclusions as to which anti-carbon coating showed the best performance. The final 70 hour tests did show that AMCX AMC26 demonstrated the lowest discoloration of the metal out of the three down selected anti-carbon coatings. This discoloration did not relate to carbon but could be a useful result when carbon growth rate is not the only concern. Unplanned variations in the series of tests must be considered and may have altered the results. Reliable conclusions could only be drawn from consistent, repeatable testing beyond the allotted time and funding for this project. Milestones 3 and 4 focused on the creation of a preheating pressure atomizer and mixing chamber. A design of experiment test helped identify a configuration of the preheating injector, Build 1, which showed a very uniform fuel spray flow field. This injector was improved upon by the creation of a Build 2 injector. Build 2 of the preheating injector demonstrated promising SMD results with only 22psi fuel pressure and 0.7 in H2O of Air. It was apparent from testing and CFD that this Build 2 has flow field recirculation zones. These recirculation zones may suggest that this Build 2 atomizer and mixer would require steam injection to reduce the auto ignition potential. It is also important to note that to achieve uniform mixing within a short distance, some recirculation is necessary. Milestone 5 generated CFD and FEA results that could be used to optimize the preheating injector. CFD results confirmed the recirculation zones seen in test data and confirmed that the flow field would not change when attached to a reformer. The FEA predicted fuel wetted wall temperatures which led to several suggested improvements that could possibly improve nozzle efficiency. Milestone 6 (originally an optional task) took a different approach than the preheating pressure atomizer. It focused on creation and optimization of a piezoelectric injector which could perform at extremely low fuel pressures. The piezoelectric atomizer showed acceptable SMD results with fuel pressure less than 1.0 psig and air pressure less than 1.0 in H2O. These SMD values were enhanced when a few components were changed, and it is expected would improve further still at elevated air temperatures. It was demonstrated that the piezoelectric injector could accomplish the desired task. The addition of phase tracking and a burst mode to the frequency controller increased the usability of the piezoelectric injector. This injector is ready to move on to the next phase of development. Engine Components has met the required program milestones of this project. Some of the Milestones were adjusted to allow Milestone 6 to be completed in parallel with the other Milestones. Because of this, Task 3.10 and 3.13 were made optional instead of Milestone 6. Engine Components was extremely grateful for the support that was provided by NETL in support of this work.

Spencer Pack

2007-12-31T23:59:59.000Z

292

Page iManaging Investment Climate Reforms: Viet Nam Case Study Table of Contents  

E-Print Network (OSTI)

The primary objective of this study is to learn about Viet Nam’s experience with reforms aimed at facilitating private entry into businesses, and in particular to understand how the reform process itself was managed, what have been the results or outcomes of the reforms, and what lessons have been learned. The focus of the analysis is the Enterprise Law reform episode and related reforms to promote domestic private sector development in Viet Nam.

Viet Nam; Raymond Mallon; Economic Consultant

2004-01-01T23:59:59.000Z

293

Reforming The Government Hiring Process | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reforming The Government Hiring Process Reforming The Government Hiring Process Reforming The Government Hiring Process November 19, 2010 - 10:10am Addthis Rita Franklin Rita Franklin Deputy Chief Human Capital Officer What does this mean for me? In the video, Deputy Secretary Daniel Poneman highlights the Department's "Time-to-Hire Tracking and Reporting System." The Department reduced the end-to-end time-to-hire from 174 calendar days for Fiscal Year FY 2009 to 100 days for FY 2010. Wednesday, Deputy Secretary Daniel Poneman and I met with leaders from across the Federal government to share our progress in the our Department's hiring reform efforts. Six months ago, President Obama called on all executive departments and federal agencies to overhaul the way we recruit and hire. As the President

294

Intelligence Reform and Terroroism Prevention Act - December 17, 2004 |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Intelligence Reform and Terroroism Prevention Act - December 17, Intelligence Reform and Terroroism Prevention Act - December 17, 2004 Intelligence Reform and Terroroism Prevention Act - December 17, 2004 December 17, 2004 To reform the intelligence community and the intelligence and intelligence-related activities of the United States Government, and for other purposes. SEC. 102. (a) DIRECTOR OF NATIONAL INTELLIGENCE.-(1) There is a Director of National Intelligence who shall be appointed by the President, by and with the advice and consent of the Senate. Any individual nominated for appointment as Director of National Intelligence shall have extensive national security expertise. ''(2) The Director of National Intelligence shall not be located within the Executive Office of the President. ''(b) PRINCIPAL RESPONSIBILITY.-Subject to the authority, direction,

295

Reforming The Government Hiring Process | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Reforming The Government Hiring Process Reforming The Government Hiring Process Reforming The Government Hiring Process November 19, 2010 - 10:10am Addthis Rita Franklin Rita Franklin Deputy Chief Human Capital Officer What does this mean for me? In the video, Deputy Secretary Daniel Poneman highlights the Department's "Time-to-Hire Tracking and Reporting System." The Department reduced the end-to-end time-to-hire from 174 calendar days for Fiscal Year FY 2009 to 100 days for FY 2010. Wednesday, Deputy Secretary Daniel Poneman and I met with leaders from across the Federal government to share our progress in the our Department's hiring reform efforts. Six months ago, President Obama called on all executive departments and federal agencies to overhaul the way we recruit and hire. As the President

296

Chemical simulation of hydrogen generation in a plasma fuel reformer  

E-Print Network (OSTI)

A model for a plasma fuel reformer or plasmatron has been developed. The model was based in a series of experiments realized at the Plasma Science and Fusion Center with such a plasmatron. The device is set up to produce ...

Margarit Bel, Nuria, 1977-

2004-01-01T23:59:59.000Z

297

The stability of coerced economic reform : the case of IPR  

E-Print Network (OSTI)

Theories in international relations posit, and empirical evidence has verified, that unwilling states can be compelled by another state or by an international institution to enact domestic policy reform. However, these ...

Wilcox, Trudy

2005-01-01T23:59:59.000Z

298

Study on Hydrogen-Enriching Gas Reforming in Smelting ... - TMS  

Science Conference Proceedings (OSTI)

May 1, 2007 ... For the two-step smelting reduction iron-making process, the advantages of hydrogen-enriching gas reforming are not only to lower the export ...

299

Separation of hydrogen from a catalytic reforming zone effluent stream  

Science Conference Proceedings (OSTI)

A process for the catalytic reforming of a hydrocarbonaceous feedstock at reforming conditions including a pressure of from about 50 to about 250 psig. Is disclosed. A portion of the hydrogen-rich vapor phase recovered from the reforming zone effluent at a relatively low pressure is compressed and recycled to the reforming zone without further purification. The balance of said hydrogen-rich vapor phase, or the net hydrogen, is compressed to a relatively high pressure and recontacted with at least a portion of the liquid hydrocarbon phase recovered from said low pressure separation to effect a further purification of said net hydrogen and to maximize the recovery of C/sub 3/-C/sub 6/+ the liquid phase.

Schmelzer, E.; Tagamolila, C.P.

1983-02-22T23:59:59.000Z

300

Hanford Low Activity Waste (LAW) Fluidized Bed Steam Reformer...  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Hanford Low Activity Waste (LAW) Fluidized Bed Steam Reformer (FBSR) Na-Al-Si (NAS) Waste Form Qualification C.M. Jantzen and E.M. Pierce November 18, 2010 2 Participating...

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


301

Hydrogen & Fuel Cells - Hydrogen - Distributed Ethanol Reforming  

NLE Websites -- All DOE Office Websites (Extended Search)

Hydrogen from Bio-Derived Liquids Hydrogen from Bio-Derived Liquids Bio-derived liquid fuels can be produced from renewable agricultural products, such as wood chips. Background Bio-derived renewable fuels are attractive for their high energy density and ease of transport. One scenario for a sustainable hydrogen economy considers that these bio-derived liquid fuels will be produced at plants close to the biomass resource, and then transported to distributed hydrogen production centers (e.g., hydrogen refueling stations), where the fuels will be reformed via the steam reforming process, similar to the current centralized production of hydrogen by the steam reforming of natural gas. Hydrogen produced by reforming these fuels must first be purified and compressed to appropriate storage and dispensing pressures. Compressing

302

Electrical Generation Tax Reform Act (Montana) | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Generation Tax Reform Act (Montana) Generation Tax Reform Act (Montana) Electrical Generation Tax Reform Act (Montana) < Back Eligibility Utility Fed. Government Commercial Agricultural Investor-Owned Utility State/Provincial Govt Industrial Municipal/Public Utility Local Government Residential Installer/Contractor Rural Electric Cooperative Tribal Government Low-Income Residential Schools Institutional Multi-Family Residential Systems Integrator Nonprofit General Public/Consumer Transportation Savings Category Alternative Fuel Vehicles Hydrogen & Fuel Cells Buying & Making Electricity Water Home Weatherization Solar Wind Program Info State Montana Program Type Fees Provider Montana Department of Revenue This Act reforms taxes paid by electricity generators to reduce tax rates and imposes replacement taxes in response to the 1997 restructuring of the

303

Reforming the Power Sector in Transition: Do Institutions Matter?  

E-Print Network (OSTI)

  tempted  to  add  additional generation capacity through meaningful power sector reforms in the lurch  towards reducing energy dependency.    As  of  1989,  numerous  nuclear  reactors  in  Armenia,  Bulgaria,  Lithuania,  Russia,  Slovakia...  relationship between country level institutions and power sector reforms    Although  the  neoclassical  economic  theory  considers  both  competition  and  privatization  as  the  core  aspects  of  a market  economy;  the  outcomes  cannot  be  guaranteed  to  be  Pareto  efficient  in  the  absence  of  proper  institutional...

Nepal, Rabindra; Jamasb, Tooraj

304

Quick-start catalyzed methanol partial oxidation reformer  

DOE Green Energy (OSTI)

The catalytic methanol partial oxidation reformer described in this paper offers all the necessary attributes for use in transportation fuel cell systems. The bench-scale prototype methanol reformer developed at Argonne is a cylindrical reactor loaded with copper zinc oxide catalyst. Liquid methanol, along with a small amount of water, is injected as a fine spray into a flowing air stream, past an igniter onto the catalyst bed where the partial oxidation reaction takes place.

Ahmed, S.; Kumar, R.

1995-12-01T23:59:59.000Z

305

Catalytic autothermal reforming of hydrocarbon fuels for fuel cells.  

DOE Green Energy (OSTI)

Fuel cell development has seen remarkable progress in the past decade because of an increasing need to improve energy efficiency as well as to address concerns about the environmental consequences of using fossil fuel for producing electricity and for propulsion of vehicles [1]. The lack of an infrastructure for producing and distributing H{sub 2} has led to a research effort to develop on-board fuel processing technology for reforming hydrocarbon fuels to generate H{sub 2} [2]. The primary focus is on reforming gasoline, because a production and distribution infrastructure for gasoline already exists to supply internal combustion engines [3]. Existing reforming technology for the production of H{sub 2} from hydrocarbon feedstocks used in large-scale manufacturing processes, such as ammonia synthesis, is cost prohibitive when scaled down to the size of the fuel processor required for transportation applications (50-80 kWe) nor is it designed to meet the varying power demands and frequent shutoffs and restarts that will be experienced during normal drive cycles. To meet the performance targets required of a fuel processor for transportation applications will require new reforming reactor technology developed to meet the volume, weight, cost, and operational characteristics for transportation applications and the development of new reforming catalysts that exhibit a higher activity and better thermal and mechanical stability than reforming catalysts currently used in the production of H{sub 2} for large-scale manufacturing processes.

Krumpelt, M.; Krause, T.; Kopasz, J.; Carter, D.; Ahmed, S.

2002-01-11T23:59:59.000Z

306

Fractionation of reformate: A new variant of gasoline production technology  

Science Conference Proceedings (OSTI)

The Novo-Ufa Petroleum Refinery is the largest domestic producer of the unique high-octane unleaded automotive gasolines AI-93 and AI-95 and the aviation gasolines B-91/115 and B-92. The base component for these gasolines is obtained by catalytic reforming of wide-cut naphtha; this basic component is usually blended with certain other components that are expensive and in short supply: toluene, xylenes, and alkylate. For example, the unleaded gasoline AI-93 has been prepared by blending reformate, alkylate, and toluene in a 65:20:15 weight ratio; AI-95 gasoline by blending alkylate and xylenes in an 80:20 weight ratio; and B-91/115 gasoline by compounding a reformate obtained with light straight-run feed, plus alkylate and toluene, in a 55:35:10 weight ratio. Toluene and xylenes have been obtained by process schemes that include the following consecutive processes: redistillation of straight-run naphtha cuts to segregate the required narrow fraction; catalytic reforming (Platforming) of the narrow toluene-xylene straight-run fraction; azeotropic distillation of the reformate to recover toluene and xylenes. A new technology based on the use of reformate fractions is proposed.

Karakuts, V.N.; Tanatarov, M.A.; Telyashev, G.G. [and others

1995-07-01T23:59:59.000Z

307

Distributed Generation Study/10 West 66th Street Corp | Open Energy  

Open Energy Info (EERE)

10 West 66th Street Corp 10 West 66th Street Corp < Distributed Generation Study Jump to: navigation, search Study Location New York, New York Site Description Residential-Multifamily-Single Building Study Type Long-term Monitoring Technology Microturbine Prime Mover Ingersoll Rand I-R PowerWorks 70 Heat Recovery Systems Built-in Fuel Natural Gas System Installer DSM Engineering System Enclosure Indoor System Application Combined Heat and Power Number of Prime Movers 1 Stand-alone Capability None Power Rating 70 kW0.07 MW 70,000 W 70,000,000 mW 7.0e-5 GW 7.0e-8 TW Nominal Voltage (V) 480 Heat Recovery Rating (BTU/hr) 300000 Cooling Capacity (Refrig/Tons) Origin of Controller 3rd Party Off-the-Shelf Component Integration Customer Assembled Start Date 2005/11/17 Monitoring Termination Date 1969/12/31

308

DOE Challenge Home Case Study, StreetScape Development, LLC, Libertyville, IL, Custom  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

StreetScape StreetScape Development, LLC Libertyville, IL BUILDING TECHNOLOGIES OFFICE DOE Challenge Home builders are in the top 1% of builders in the country meeting the extraordinary levels of excellence and quality specifi ed by the U.S. Department of Energy. Every DOE Challenge Home starts with ENERGY STAR for Homes Version 3 for an energy-effi cient home built on a solid foundation of building science research. Then, even more advanced technologies are designed in for a home that goes above and beyond current code to give you the superior quality construction, HVAC, appliances, indoor air quality, safety, durability, comfort, and solar-ready components along with ultra-low or no utility bills. This provides homeowners with a quality home that will last for generations to come.

309

Chromatin Regulation and Low Dose Irradiation: A Two-Way Street ?  

NLE Websites -- All DOE Office Websites (Extended Search)

Chromatin Regulation and Low Dose Irradiation: A Two-Way Street ? Chromatin Regulation and Low Dose Irradiation: A Two-Way Street ? Irene Chiolo, Sylvain Costes and Gary H. Karpen. Lawrence Berkeley National Lab and UC Berkeley, Berkeley, CA Goal: We are trying to understand the impact of exposure to low-dose ionizing radiation on epigenetic mechanisms, chromatin organization and functional responses, and how these processes affect the response to low-dose radiation. Background/Significance: Genomic instability (GI) is one of the hallmarks of cancer that contributes to genetic diversity and has been associated with exposure to ionizing radiation (IR) (1,2). Radiobiology dogma has focused on DNA as the likely target for GI effects of radiation, but until fairly recently, without incorporating roles for chromatin.

310

Chromatin Regulation and Low Dose Irradiation: A Two-Way Street?  

NLE Websites -- All DOE Office Websites (Extended Search)

Chromatin Regulation and Low Dose Irradiation: A Two-Way Street? Chromatin Regulation and Low Dose Irradiation: A Two-Way Street? Irene Chiolo Lawrence Berkeley National Lab Abstract Goal: We are trying to understand the impact of exposure to low-dose ionizing radiation on epigenetic mechanisms, chromatin organization and functional responses, and how these processes affect the response to low-dose radiation. Background/Significance: Genomic instability (GI) is one of the hallmarks of cancer that contributes to genetic diversity and has been associated with exposure to ionizing radiation (IR) (1,2). Radiobiology dogma has focused on DNA as the likely target for GI effects of radiation, but until fairly recently, without incorporating roles for chromatin. Eukaryotic genomes contain two major chromatin domains: heterochromatin and

311

Comparing Light-Emitting Diode (LED) Street and Area Lighting to Traditional Lighting Technologies  

Science Conference Proceedings (OSTI)

In 2008, the Tennessee Valley Authority (TVA) and Benton County Electric System partnered with the Electric Power Research Institute (EPRI) to launch an investigation into the use of LED technology for area lighting. The goal of the project—called the LED Street and Area Lighting Demonstration—was to discover a better light bulb, one that not only meets the outdoor lighting requirements of consumers, but also uses less electricity in doing so. This case study discusses the results of ...

2012-09-28T23:59:59.000Z

312

Performance comparison between partial oxidation and methane steam reforming processes for solid oxide fuel cell (SOFC) micro combined heat and  

E-Print Network (OSTI)

Performance comparison between partial oxidation and methane steam reforming processes for solid recirculation are used along with steam methane reforming. Further Steam Methane Reforming process produces Cell fueled by natural gas with two different types of pre-reforming systems, namely Steam Reforming

Liso, Vincenzo

313

EERE Roofus' Solar and Efficient Home: Walls  

NLE Websites -- All DOE Office Websites (Extended Search)

Walls Insulation Windows Activities Printable Version Walls Illustration of Roofus, a golden retriever, sitting in front of a wall. On cold nights, you use a blanket to keep you...

314

Wall Insulation; BTS Technology Fact Sheet  

SciTech Connect

Properly sealed, moisture-protected, and insulated walls help increase comfort, reduce noise, and save on energy costs. This fact sheet addresses these topics plus advanced framing techniques, insulation types, wall sheathings, and steps for effective wall construction and insulation.

Southface Energy Institute; Tromly, K.

2000-11-07T23:59:59.000Z

315

The National Science Bowl Students are Here! (The Streets of D.C. Just Got  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The National Science Bowl Students are Here! (The Streets of D.C. The National Science Bowl Students are Here! (The Streets of D.C. Just Got a Little Smarter.) The National Science Bowl Students are Here! (The Streets of D.C. Just Got a Little Smarter.) April 28, 2011 - 3:45pm Addthis Ginny Simmons Ginny Simmons Former Managing Editor for Energy.gov, Office of Public Affairs Hundreds of America's best science high school and middle school students are arriving in D.C. today to gear up for the National Science Bowl. For the last few months, more than 14,000 students from 1,800 schools competed in 110 regional matches -- all to determine the best science teams in the nation. After a series of run-off competitions this weekend, the best-of-the-best, last-standing teams will compete in the Science Bowl finals on Monday, May 2, to determine the 2011 national middle and high

316

The National Science Bowl Students are Here! (The Streets of D.C. Just Got  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

The National Science Bowl Students are Here! (The Streets of D.C. The National Science Bowl Students are Here! (The Streets of D.C. Just Got a Little Smarter.) The National Science Bowl Students are Here! (The Streets of D.C. Just Got a Little Smarter.) April 28, 2011 - 3:45pm Addthis Ginny Simmons Ginny Simmons Former Managing Editor for Energy.gov, Office of Public Affairs Hundreds of America's best science high school and middle school students are arriving in D.C. today to gear up for the National Science Bowl. For the last few months, more than 14,000 students from 1,800 schools competed in 110 regional matches -- all to determine the best science teams in the nation. After a series of run-off competitions this weekend, the best-of-the-best, last-standing teams will compete in the Science Bowl finals on Monday, May 2, to determine the 2011 national middle and high

317

THOR Bench-Scale Steam Reforming Demonstration  

SciTech Connect

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a ''road ready'' waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrates were not detected in the product and NOx destruction exceeded 98%. The demonstration was successful.

Marshall, D.W.; Soelberg, N.R.; Shaber, K.M.

2003-05-21T23:59:59.000Z

318

THOR Bench-Scale Steam Reforming Demonstration  

SciTech Connect

The Idaho Nuclear Technology and Engineering Center (INTEC) was home to nuclear fuel reprocessing activities for decades at the Idaho National Engineering and Environmental Laboratory. As a result of the reprocessing activities, INTEC has accumulated approximately one million gallons of acidic, radioactive, sodium-bearing waste (SBW). The purpose of this demonstration was to investigate a reforming technology, offered by THORsm Treatment Technologies, LLC, for treatment of SBW into a "road ready" waste form that would meet the waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP). A non-radioactive simulated SBW was used based on the known composition of waste tank WM-180 at INTEC. Rhenium was included as a non-radioactive surrogate for technetium. Data was collected to determine the nature and characteristics of the product, the operability of the technology, the composition of the off-gases, and the fate of key radionuclides (cesium and technetium) and volatile mercury compounds. The product contained a low fraction of elemental carbon residues in the cyclone and filter vessel catches. Mercury was quantitatively stripped from the product but cesium, rhenium (Tc surrogate), and the heavy metals were retained. Nitrates were not detected in the product and NOx destruction exceeded 98%. The demonstration was successful.

D. W. Marshall; N. R. Soelberg; K. M. Shaber

2003-05-01T23:59:59.000Z

319

Security_Walls_VPP_Award  

NLE Websites -- All DOE Office Websites (Extended Search)

Security Force Recognized for Outstanding Safety CARLSBAD, N.M., May 10, 2013 - The U.S. Department of Energy (DOE) has awarded Security Walls, LLC, the Waste Isolation Pilot...

320

Properties of the Wind Field within the Oklahoma City Park Avenue Street Canyon. Part I: Mean Flow and Turbulence Statistics  

Science Conference Proceedings (OSTI)

Velocity data were obtained from sonic anemometer measurements within an east–west-running street canyon located in the urban core of Oklahoma City, Oklahoma, during the Joint Urban 2003 field campaign. These data were used to explore the ...

M. A. Nelson; E. R. Pardyjak; J. C. Klewicki; S. U. Pol; M. J. Brown

2007-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


321

Rolls, Streets, Waves, and More: A Review of Quasi-Two-Dimensional Structures in the Atmospheric Boundary Layer  

Science Conference Proceedings (OSTI)

The atmospheric boundary layer is home to a number of horizontally elongated quasi-two-dimensionalphenomena including cloud streets, roll vortices, thermal waves, and surface layer streaks. These phenomena, their dynamics, and their interactions ...

George S. Young; David A. R. Kristovich; Mark R. Hjelmfelt; Ralph C. Foster

2002-07-01T23:59:59.000Z

322

Microchannel Process Technology for Compact Methane Steam Reforming  

Science Conference Proceedings (OSTI)

The study of microchannel reaction engineering and applications to compact chemical reactors has expanded rapidly both academically and industrially in recent years. Velocys{reg_sign}, a spin-out company from Battelle Memorial Institute, is commercializing microchannel process technology for large-scale chemical processing. Hydrogen production at industrial rates in compact Velocys hardware is made possible through increases in both heat and mass transfer rates for highly active and novel catalysts. In one example, a microchannel methane steam reforming reactor is presented with integrated catalytic partial oxidation of methane prior to catalytic combustion with low excess air (25%) to generate the required energy for undothermic methane steam reforming in adjacent channels. Heat transfer rates from the exothermic reactions exceed 18 W/cm{sup 2} of interplanar heat transfer surface area and exceed 65 W/cm{sup 3} of total reaction volume for a methane steam reforming contact time near 4 milliseconds. The process intensity of the Velocys methane steam reformer well exceeds that of conventional steam reformers, which have a typical volumetric heat flux below 1 W/cm{sup 3}. The integration of multiple unit operations and improvements in process intensification result in significant capital and operating cost savings for commercial applications.

Tonkovich, A L.; Perry, Steve; Wang, Yong; Qiu, Dongming; LaPlante, Timothy J.; Rogers, William A.

2004-12-01T23:59:59.000Z

323

Methanol reformers for fuel cell powered vehicles: Some design considerations  

DOE Green Energy (OSTI)

Fuel cells are being developed for use in automotive propulsion systems as alternatives for the internal combustion engine in buses, vans, passenger cars. The two most important operational requirements for a stand-alone fuel cell power system for a vehicle are the ability to start up quickly and the ability to supply the necessary power on demand for the dynamically fluctuating load. Methanol is a likely fuel for use in fuel cells for transportation applications. It is a commodity chemical that is manufactured from coal, natural gas, and other feedstocks. For use in a fuel cell, however, the methanol must first be converted (reformed) to a hydrogen-rich gas mixture. The desired features for a methanol reformer include rapid start-up, good dynamic response, high fuel conversion, small size and weight, simple construction and operation, and low cost. In this paper the present the design considerations that are important for developing such a reformer, namely: (1) a small catalyst bed for quick starting, small size, and low weight; (2) multiple catalysts for optimum operation of the dissociation and reforming reactions; (3) reforming by direct heat transfer partial oxidation for rapid response to fluctuating loads; and (4) thermal independence from the rest of the fuel cell system. 10 refs., 1 fig.

Kumar, R.; Ahmed, S.; Krumpelt, M.; Myles, K.M.

1990-01-01T23:59:59.000Z

324

Reformers for the production of hydrogen from methanol and alternative fuels for fuel cell powered vehicles  

DOE Green Energy (OSTI)

The objective of this study was (i) to assess the present state of technology of reformers that convert methanol (or other alternative fuels) to a hydrogen-rich gas mixture for use in a fuel cell, and (ii) to identify the R D needs for developing reformers for transportation applications. Steam reforming and partial oxidation are the two basic types of fuel reforming processes. The former is endothermic while the latter is exothermic. Reformers are therefore typically designed as heat exchange systems, and the variety of designs used includes shell-and-tube, packed bed, annular, plate, and cyclic bed types. Catalysts used include noble metals and oxides of Cu, Zn, Cr, Al, Ni, and La. For transportation applications a reformer must be compact, lightweight, and rugged. It must also be capable of rapid start-up and good dynamic performance responsive to fluctuating loads. A partial oxidation reformer is likely to be better than a steam reformer based on these considerations, although its fuel conversion efficiency is expected to be lower than that of a steam reformer. A steam reformer better lends itself to thermal integration with the fuel cell system; however, the thermal independence of the reformer from the fuel cell stack is likely to yield much better dynamic performance of the reformer and the fuel cell propulsion power system. For both steam reforming and partial oxidation reforming, research is needed to develop compact, fast start-up, and dynamically responsive reformers. For transportation applications, steam reformers are likely to prove best for fuel cell/battery hybrid power systems, and partial oxidation reformers are likely to be the choice for stand-alone fuel cell power systems.

Kumar, R.; Ahmed, S.; Krumpelt, M.; Myles, K.M.

1992-08-01T23:59:59.000Z

325

Reformers for the production of hydrogen from methanol and alternative fuels for fuel cell powered vehicles  

DOE Green Energy (OSTI)

The objective of this study was (i) to assess the present state of technology of reformers that convert methanol (or other alternative fuels) to a hydrogen-rich gas mixture for use in a fuel cell, and (ii) to identify the R&D needs for developing reformers for transportation applications. Steam reforming and partial oxidation are the two basic types of fuel reforming processes. The former is endothermic while the latter is exothermic. Reformers are therefore typically designed as heat exchange systems, and the variety of designs used includes shell-and-tube, packed bed, annular, plate, and cyclic bed types. Catalysts used include noble metals and oxides of Cu, Zn, Cr, Al, Ni, and La. For transportation applications a reformer must be compact, lightweight, and rugged. It must also be capable of rapid start-up and good dynamic performance responsive to fluctuating loads. A partial oxidation reformer is likely to be better than a steam reformer based on these considerations, although its fuel conversion efficiency is expected to be lower than that of a steam reformer. A steam reformer better lends itself to thermal integration with the fuel cell system; however, the thermal independence of the reformer from the fuel cell stack is likely to yield much better dynamic performance of the reformer and the fuel cell propulsion power system. For both steam reforming and partial oxidation reforming, research is needed to develop compact, fast start-up, and dynamically responsive reformers. For transportation applications, steam reformers are likely to prove best for fuel cell/battery hybrid power systems, and partial oxidation reformers are likely to be the choice for stand-alone fuel cell power systems.

Kumar, R.; Ahmed, S.; Krumpelt, M.; Myles, K.M.

1992-08-01T23:59:59.000Z

326

Domain walls riding the wave.  

SciTech Connect

Recent years have witnessed a rapid proliferation of electronic gadgets around the world. These devices are used for both communication and entertainment, and it is a fact that they account for a growing portion of household energy consumption and overall world consumption of electricity. Increasing the energy efficiency of these devices could have a far greater and immediate impact than a gradual switch to renewable energy sources. The advances in the area of spintronics are therefore very important, as gadgets are mostly comprised of memory and logic elements. Recent developments in controlled manipulation of magnetic domains in ferromagnet nanostructures have opened opportunities for novel device architectures. This new class of memories and logic gates could soon power millions of consumer electronic devices. The attractiveness of using domain-wall motion in electronics is due to its inherent reliability (no mechanical moving parts), scalability (3D scalable architectures such as in racetrack memory), and nonvolatility (retains information in the absence of power). The remaining obstacles in widespread use of 'racetrack-type' elements are the speed and the energy dissipation during the manipulation of domain walls. In their recent contribution to Physical Review Letters, Oleg Tretiakov, Yang Liu, and Artem Abanov from Texas A&M University in College Station, provide a theoretical description of domain-wall motion in nanoscale ferromagnets due to the spin-polarized currents. They find exact conditions for time-dependent resonant domain-wall movement, which could speed up the motion of domain walls while minimizing Ohmic losses. Movement of domain walls in ferromagnetic nanowires can be achieved by application of external magnetic fields or by passing a spin-polarized current through the nanowire itself. On the other hand, the readout of the domain state is done by measuring the resistance of the wire. Therefore, passing current through the ferromagnetic wire is the preferred method, as it combines manipulation and readout of the domain-wall state. The electrons that take part in the process of readout and manipulation of the domain-wall structure in the nanowire do so through the so-called spin transfer torque: When spin-polarized electrons in the ferromagnet nanowire pass through the domain wall they experience a nonuniform magnetization, and they try to align their spins with the local magnetic moments. The force that the electrons experience has a reaction force counterpart that 'pushes' the local magnetic moments, resulting in movement of the domain wall in the direction of the electron flow through the spin-transfer torque. The forces between the electrons and the local magnetic moments in the ferromagnet also create additional electrical resistance for the electrons passing through the domain wall. By measuring resistance across a segment of the nanowire, one determines if a domain wall is present; i.e., one can read the stored information. The interaction of the spin-polarized electrons with the domain wall in the ferromagnetic nanowire is not very efficient. Even for materials achieving high polarization of the free electrons, it is very difficult to move the magnetic domain wall. Several factors contribute to this problem, with imperfections of the ferromagnetic nanowire that cause domain-wall pinning being the dominant one. Permalloy nanowires, one of the best candidates for domain-wall-based memory and logic devices, require current densities of the order of 10{sup 8} A/cm{sup 2} in order to move a domain wall from a pinning well. Considering that this current has to pass through a relatively long wire, it is not very difficult to imagine that most of the energy will go to Joule heating. The efficiency of the process - the ratio of the energy converted to domain-wall motion to the total energy consumed - is comparable to that of an incandescent light bulb converting electricity to light. A step towards more efficient domain-wall-based memory devices is the advance of using alternating currents or curren

Karapetrov, G.; Novosad, V.; Materials Science Division

2010-11-01T23:59:59.000Z

327

Forest Tenure Reform in Vietnam | Open Energy Information  

Open Energy Info (EERE)

in Vietnam in Vietnam Jump to: navigation, search Name Forest Tenure Reform in Vietnam Agency/Company /Organization Regional Community Forestry Training Center for Asia and the Pacific Sector Land Focus Area Forestry Topics Resource assessment, Background analysis Resource Type Lessons learned/best practices Website http://recoftc.org/site/filead Country Vietnam UN Region South-Eastern Asia References Forest Tenure Reform in Vietnam[1] Forest Tenure Reform in Vietnam Screenshot Summary "This report presents a synthesis of findings from the two surveys undertaken in Dak Lak (by Dak Lak Department of Agriculture and Rural Development (DARD)) and Hoa Binh by VFU (See Annex A. for a list of members in the two research teams). It was prepared by Nguyen Quang Tan, Nguyen Ba

328

Regulatory and Financial Reform of Federal Research Policy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Regulatory and Financial Reform of Federal Research Policy Regulatory and Financial Reform of Federal Research Policy Recommendations to the NRC Committee on Research Universities January 21, 2011 Introduction At the request of the National Research Council (NRC) Committee on Research Universities, the Council on Governmental Relations (COGR), the Association of American Universities (AAU), and the Association of Public and Land-grant Universities (APLU) have assembled a set of ten recommendations for regulatory reform that would improve research universities' ability to carry out their missions without requiring a significant financial investment by the Federal government. We firmly believe that compliance and regulatory oversight are essential to the conduct of federally-supported research. Rationalizing the Federal regulatory infrastructure is essential to

329

Comments on Request For Information regarding Reducing Regulatory Reform  

NLE Websites -- All DOE Office Websites (Extended Search)

Comments on Request For Information regarding Reducing Regulatory Comments on Request For Information regarding Reducing Regulatory Reform issued February 3, 2011 (Federal Register /Vol. 76, No. 23 /Thursday, February 3, 2011 /Notices). Comments on Request For Information regarding Reducing Regulatory Reform issued February 3, 2011 (Federal Register /Vol. 76, No. 23 /Thursday, February 3, 2011 /Notices). I have reviewed the Request For Information regarding Reducing Regulatory Reform issued February 3, 2011 (Federal Register /Vol. 76, No. 23 /Thursday, February 3, 2011 /Notices). In the Department of Energy"s (DOE) attempt to meet its obligation to implement Executive Order 13563, ""Improving Regulation and Regulatory Review,"" issued by the President on January 18, 2011, I recommend DOE make a bold move to change

330

Pyrochlore-type catalysts for the reforming of hydrocarbon fuels  

DOE Patents (OSTI)

A method of catalytically reforming a reactant gas mixture using a pyrochlore catalyst material comprised of one or more pyrochlores having the composition A.sub.2-w-xA'.sub.wA''.sub.xB.sub.2-y-zB'.sub.yB''.sub.zO.sub.7-.DELTA.. Distribution of catalytically active metals throughout the structure at the B site creates an active and well dispersed metal locked into place in the crystal structure. This greatly reduces the metal sintering that typically occurs on supported catalysts used in reforming reactions, and reduces deactivation by sulfur and carbon. Further, oxygen mobility may also be enhanced by elemental exchange of promoters at sites in the pyrochlore. The pyrochlore catalyst material may be utilized in catalytic reforming reactions for the conversion of hydrocarbon fuels into synthesis gas (H.sub.2+CO) for fuel cells, among other uses.

Berry, David A. (Morgantown, WV); Shekhawat, Dushyant (Morgantown, WV); Haynes, Daniel (Morgantown, WV); Smith, Mark (Morgantown, WV); Spivey, James J. (Baton Rouge, LA)

2012-03-13T23:59:59.000Z

331

Pyrochlore-type catalysts for the reforming of hydrocarbon fuels  

Science Conference Proceedings (OSTI)

A method of catalytically reforming a reactant gas mixture using a pyrochlore catalyst material comprised of one or more pyrochlores having the composition A.sub.2-w-xA'.sub.wA''.sub.xB.sub.2-y-zB'.sub.yB''.sub.zO.sub.7-.DELTA.. Distribution of catalytically active metals throughout the structure at the B site creates an active and well dispersed metal locked into place in the crystal structure. This greatly reduces the metal sintering that typically occurs on supported catalysts used in reforming reactions, and reduces deactivation by sulfur and carbon. Further, oxygen mobility may also be enhanced by elemental exchange of promoters at sites in the pyrochlore. The pyrochlore catalyst material may be utilized in catalytic reforming reactions for the conversion of hydrocarbon fuels into synthesis gas (H.sub.2+CO) for fuel cells, among other uses.

Berry, David A. (Morgantown, WV); Shekhawat, Dushyant (Morgantown, WV); Haynes, Daniel (Morgantown, WV); Smith, Mark (Morgantown, WV); Spivey, James J. (Baton Rouge, LA)

2012-03-13T23:59:59.000Z

332

Producing Clean Syngas via Catalytic Reforming for Fuels Production  

Science Conference Proceedings (OSTI)

Thermochemical biomass conversion to fuels and chemicals can be achieved through gasification to syngas. The biomass derived raw syngas contains the building blocks of carbon monoxide and hydrogen as well as impurities such as tars, light hydrocarbons, and hydrogen sulfide. These impurities must be removed prior to fuel synthesis. We used catalytic reforming to convert tars and hydrocarbons to additional syngas, which increases biomass carbon utilization. In this work, nickel based, fluidizable tar reforming catalysts were synthesized and evaluated for tar and methane reforming performance with oak and model syngas in two types of pilot scale fluidized reactors (recirculating and recirculating regenerating). Because hydrogen sulfide (present in raw syngas and added to model syngas) reacts with the active nickel surface, regeneration with steam and hydrogen was required. Pre and post catalyst characterization showed changes specific to the syngas type used. Results of this work will be discussed in the context of selecting the best process for pilot scale demonstration.

Magrini, K. A.; Parent, Y.; Jablonski, W.; Yung, M.

2012-01-01T23:59:59.000Z

333

Ghana-REDD Readiness Requires Radical Reform | Open Energy Information  

Open Energy Info (EERE)

Readiness Requires Radical Reform Readiness Requires Radical Reform Jump to: navigation, search Name Ghana-REDD Readiness Requires Radical Reform Agency/Company /Organization UN-REDD Programme Sector Land Focus Area Forestry, Agriculture Topics Implementation, GHG inventory, Policies/deployment programs, Resource assessment, Pathways analysis, Background analysis Resource Type Maps, Guide/manual, Training materials Website http://environment.yale.edu/tf Country Ghana UN Region Western Africa References Ghana-REDD Readiness[1] Summary "The fundamental changes needed for sustainable forest management in Ghana have been known for years, and many large projects have been instigated accordingly. Yet real change has proved elusive. The key challenge now is to get REDD-plus right so that it makes a difference. Dialogue participants

334

High performance internal reforming unit for high temperature fuel cells  

DOE Patents (OSTI)

A fuel reformer having an enclosure with first and second opposing surfaces, a sidewall connecting the first and second opposing surfaces and an inlet port and an outlet port in the sidewall. A plate assembly supporting a catalyst and baffles are also disposed in the enclosure. A main baffle extends into the enclosure from a point of the sidewall between the inlet and outlet ports. The main baffle cooperates with the enclosure and the plate assembly to establish a path for the flow of fuel gas through the reformer from the inlet port to the outlet port. At least a first directing baffle extends in the enclosure from one of the sidewall and the main baffle and cooperates with the plate assembly and the enclosure to alter the gas flow path. Desired graded catalyst loading pattern has been defined for optimized thermal management for the internal reforming high temperature fuel cells so as to achieve high cell performance.

Ma, Zhiwen (Sandy Hook, CT); Venkataraman, Ramakrishnan (New Milford, CT); Novacco, Lawrence J. (Brookfield, CT)

2008-10-07T23:59:59.000Z

335

GUIDANCE ON APPLICATION OF FEDERAL VACANCIES REFORM ACT OF 1998 Page 1 of 13  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

APPLICATION OF FEDERAL VACANCIES REFORM ACT OF 1998 Page 1 of 13 APPLICATION OF FEDERAL VACANCIES REFORM ACT OF 1998 Page 1 of 13 GUIDANCE ON APPLICATION OF FEDERAL VACANCIES REFORM ACT OF 1998 This memorandum provides guidance on the application of the Federal Vacancies Reform Act of1998 to vacancies in Senate-confirmed offices within the executive branch. March 22, 1999 MEMORANDUM FOR AGENCY GENERAL COUNSELS On October 21, 1998, the Federal Vacancies Reform Act of 1998 ("Vacancies Reform Act" or "Act") was signed into law. ( ) The Vacancies Reform Act replaces the old Vacancies Act and alters the way in which vacancies in presidentially appointed, Senate- confirmed offices within the executive branch may be filled on a temporary basis. The following Q&As are intended to provide general guidance on the Vacancies Reform Act. If

336

Controlling Activity and Stability of Ni-YSZ Catalysts for On-Anode Reforming  

DOE Green Energy (OSTI)

The purposes of the project are to develop an effective Ni-YSZ-based anode for on-anode reforming of methane and natural gas and develop methods to control endothermic steam reforming activity.

King, D.L.; Wang, Y.; Chin, Y-H.; Lin, Y.; Roh, H-S.; Rozmiarek, B.

2005-01-27T23:59:59.000Z

337

www.elsevier.com/locate/econbase School finance reform: Assessing general equilibrium effects  

E-Print Network (OSTI)

In 1994 the state of Michigan implemented one of the most comprehensive school finance reforms undertaken to date in any of the states. Understanding the effects of the reform is thus of value in informing other potential reform initiatives. In addition, the reform and associated changes in the economic environment provide an opportunity to assess whether a simple general equilibrium model can be of value in framing the study of such reform initiatives. In this paper, we present and use such a model to derive predictions about the effects of the reform on housing prices and neighborhood demographic compositions. Broadly, our analysis implies that the effects of the reform and changes in the economic environment are likely to have been reflected primarily in housing prices and only modestly on neighborhood demographics. We find that evidence for the Detroit metropolitan area from the decade encompassing the reform is largely consistent with the predictions of the model.

Maria Marta Ferreyra A

2007-01-01T23:59:59.000Z

338

The Lessons of Practice: Domestic Policy Reform as a Way to Address...  

Open Energy Info (EERE)

The Lessons of Practice: Domestic Policy Reform as a Way to Address Climate Change Jump to: navigation, search Tool Summary Name: The Lessons of Practice: Domestic Policy Reform as...

339

From negotiation to auction : Land-Conveyance Reform in China and its institutional and social impacts  

E-Print Network (OSTI)

The land market and the associated land-development-control mechanism in China have been experiencing a series of reforms since the 1990s, of which Land Conveyance Reform (LCR) in 2004 is a very recent and an important ...

Chen, Zhiyu (Zhiyu Jerry)

2007-01-01T23:59:59.000Z

340

ECONOMIC REFORM AND COMMUNIST REGIME SURVIVABILTY: PAST, PRESENT, AND FUTURE  

E-Print Network (OSTI)

While the collapse of communist rule and process of transitioning to democracy in the former-Soviet Union and its numerous satellite states certainly warrants the wealth of attention received, by no means does this signal that the history of communist state rule is ended. Contrary to popular belief—and even belief in academe it sometimes seems—Communism still survives. In fact, a number of Asian states still claim to follow the path to a promised societal utopia under the guidance of their respective Politburos and may be described as not only ‘surviving’ but thriving, experiencing economic stability and enjoying high rates of growth. This study examines the ramifications of economic and political reform policies implemented by four collapsed communist regimes which have transitioned to democratic governance—the former-Soviet Union, Poland, Hungary, and Czechoslovakia—as well as two surviving Asian communist regimes—Vietnam and China—in identifying characteristic patterns of reform that are conducive to regime survival and/or collapse. The end objective herein is to provide projections for the future of the Castro regime in Cuba, which faces a critical juncture in the future with the impending death of its charismatic leader. I hypothesize that economic reform, through consistent implementation, generates credibility for both Communist Party elites and their future reform endeavors. Additionally, reform packages that manage to successfully stabilize the economy bestow an increased measure of legitimacy to the political elite, allowing the Communist Party to maintain political control, thereby avoiding collapse and the transition to democracy. The third and final section contains general discussion and what conclusions can be drawn from the results, as well as analysis of the history of reform efforts to present in the Caribbean island state of Cuba.

Nelson, John

2006-08-16T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


341

Glazing and the Trombe wall  

DOE Green Energy (OSTI)

Single, double and triple glazing are examined for use in passive solar Trombe walls and south facing windows. Net gains and losses are calculated employing regional weather data and annual contribution to heating load reduction is evaluated. The study concentrates on the reflectivity of each glass pane, including the dependence of reflectivity on the angle of incidence of the radiation, and resulting heat gains and losses. This facet of passive design heretofore has been inadequately treated as is shown to be significant. The marginal value of each additional pane is investigated with regard to heat gain, energy savings and total costs. Additionally, attention is given to the effects of Trombe wall energy storage.

Pouder, R W; Leigh, R W

1978-01-01T23:59:59.000Z

342

Why are land reforms granting complete property rights politically risky? Electoral outcomes of Mexico's certification program  

E-Print Network (OSTI)

identified adverse political fallouts as the main reason whygains but fear the political fallout of the reform. It helps

de Janvry, Alain; Gonzalez-Navarro, Marco; Sadoulet, Elisabeth

2012-01-01T23:59:59.000Z

343

Tailored Macroporous SiCN and SiC Structures for High-Temperature Fuel Reforming**  

E-Print Network (OSTI)

. The catalytic reforming of hydrocarbons in a microreformer is an attractive approach to supply hydrogen to fuel

Kenis, Paul J. A.

344

Heat exchanger for fuel cell power plant reformer  

DOE Patents (OSTI)

A heat exchanger uses the heat from processed fuel gas from a reformer for a fuel cell to superheat steam, to preheat raw fuel prior to entering the reformer and to heat a water-steam coolant mixture from the fuel cells. The processed fuel gas temperature is thus lowered to a level useful in the fuel cell reaction. The four temperature adjustments are accomplished in a single heat exchanger with only three heat transfer cores. The heat exchanger is preheated by circulating coolant and purge steam from the power section during startup of the latter.

Misage, Robert (Manchester, CT); Scheffler, Glenn W. (Tolland, CT); Setzer, Herbert J. (Ellington, CT); Margiott, Paul R. (Manchester, CT); Parenti, Jr., Edmund K. (Manchester, CT)

1988-01-01T23:59:59.000Z

345

Catalytic reforming of liquid fuels: Deactivation of catalysts  

Science Conference Proceedings (OSTI)

The catalytic reforming of logistic fuels (e.g., diesel) to provide hydrogen-rich gas for various fuel cells is inevitably accompanied by deactivation. This deactivation can be caused by various mechanisms, such as carbon deposition, sintering, and sulfur poisoning. In general, these mechanisms are, not independent—e.g., carbon deposition may affect sulfur poisoning. However, they are typically studied in separate experiments, with relatively little work reported on their interaction at conditions typical of liquid fuel reforming. Recent work at the U.S. Dept. of Energy/NETL and Louisiana State University has shown progress in understanding the interaction of these deactivation processes, and catalysts designed to minimize them.

Spivey, J.J.; Haynes, D.J.; Berry, D.A.; Shekhawat, Dushyant; Gardner, T.H.

2007-10-01T23:59:59.000Z

346

EFFECT OF H2 PRODUCED THROUGH STEAM-METHANE REFORMING ON CHP PLANT EFFICIENCY  

E-Print Network (OSTI)

1 EFFECT OF H2 PRODUCED THROUGH STEAM-METHANE REFORMING ON CHP PLANT EFFICIENCY O. Le Corre1 , C@emn.fr ABSTRACT In-situ hydrogen production is carried out by a catalytic reformer kit set up into exhaust gases-thermal reforming process is achieved. Hydrogen production is mainly dependent on O2 content in exhaust gases

347

Combined Steam Reforming and Partial Oxidation of Methane to Synthesis Gas under Electrical Discharge  

E-Print Network (OSTI)

Combined Steam Reforming and Partial Oxidation of Methane to Synthesis Gas under Electrical production from simultaneous steam reforming and partial oxidation of methane using an ac corona discharge and steam reforming has a benefit in terms of balancing the heat load. Methane conversions can be achieved

Mallinson, Richard

348

Catalysts for hydrogen production by steam reforming of dimethyl ether (DME)  

Science Conference Proceedings (OSTI)

Dimethyl ether (DME) is expected as one of clean fuels. We have been studying on DME steam reforming for hydrogen production. Copper alumina catalysts prepared by a sol-gel method produced large quantities of H2 with DME steam reforming. The reason was ... Keywords: DME, alumina, catalyst, clean fuel, copper, dimethyl ether, hydrogen, sol-gel method, steam reforming

Kaoru Takeishi

2010-02-01T23:59:59.000Z

349

Solar Reforming of Carbon Dioxide to Produce Diesel Fuel  

SciTech Connect

This project focused on the demonstration of an innovative technology, referred to as the Sunexus CO2 Solar Reformer, which utilizes waste CO2 as a feedstock for the efficient and economical production of synthetic diesel fuel using solar thermal energy as the primary energy input. The Sunexus technology employs a two stage process for the conversion of CO2 to diesel fuel. A solar reforming system, including a specially designed reactor and proprietary CO2 reforming catalyst, was developed and used to convert captured CO2 rich gas streams into syngas (primarily hydrogen and carbon monoxide) using concentrated solar energy at high conversion efficiencies. The second stage of the system (which has been demonstrated under other funding) involves the direct conversion of the syngas into synthetic diesel fuel using a proprietary catalyst (Terra) previously developed and validated by Pacific Renewable Fuels and Chemicals (PRFC). The overall system energy efficiency for conversion of CO2 to diesel fuel is 74%, due to the use of solar energy. The results herein describe modeling, design, construction, and testing of the Sunexus CO2 Solar Reformer. Extensive parametric testing of the solar reformer and candidate catalysts was conducted and chemical kinetic models were developed. Laboratory testing of the Solar Reformer was successfully completed using various gas mixtures, temperatures, and gas flow rates/space velocities to establish performance metrics which can be employed for the design of commercial plants. A variety of laboratory tests were conducted including dry reforming (CO2 and CH{sub 4}), combination dry/steam reforming (CO2, CH{sub 4} & H{sub 2}O), and tri-reforming (CO2, CH{sub 4}, H{sub 2}O & O{sub 2}). CH{sub 4} and CO2 conversions averaged 95-100% and 50-90% per reformer cycle, respectively, depending upon the temperatures and gas space velocities. No formation of carbon deposits (coking) on the catalyst was observed in any of these tests. A 16 ft. diameter, concentrating solar dish was modified to accommodate the Sunexus CO2 Solar Reformer and the integrated system was installed at the Pacific Renewable Fuels and Chemicals test site at McClellan, CA. Several test runs were conducted without catalyst during which the ceramic heat exchanger in the Sunexus Solar Reformer reached temperatures between 1,050 F (566 C) and 2,200 F (1,204 C) during the test period. A dry reforming mixture of CO2/CH{sub 4} (2.0/1.0 molar ratio) was chosen for all of the tests on the integrated solar dish/catalytic reformer during December 2010. Initial tests were carried out to determine heat transfer from the collimated solar beam to the catalytic reactor. The catalyst was operated successfully at a steady-state temperature of 1,125 F (607 C), which was sufficient to convert 35% of the 2/1 CO2/CH{sub 4} mixture to syngas. This conversion efficiency confirmed the results from laboratory testing of this catalyst which provided comparable syngas production efficiencies (40% at 1,200 F [650 C]) with a resulting syngas composition of 20% CO, 16% H{sub 2}, 39% CO2 and 25% CH{sub 4}. As based upon the laboratory results, it is predicted that 90% of the CO2 will be converted to syngas in the solar reformer at 1,440 F (782 C) resulting in a syngas composition of 50% CO: 43% H{sub 2}: 7% CO2: 0% CH{sub 4}. Laboratory tests show that the higher catalyst operating temperature of 1,440 F (782 C) for efficient conversion of CO2 can certainly be achieved by optimizing solar reactor heat transfer, which would result in the projected 90% CO2-to-syngas conversion efficiencies. Further testing will be carried out during 2011, through other funding support, to further optimize the solar dish CO2 reformer. Additional studies carried out in support of this project and described in this report include: (1) An Assessment of Potential Contaminants in Captured CO2 from Various Industrial Processes and Their Possible Effect on Sunexus CO2 Reforming Catalysts; (2) Recommended Measurement Methods for Assessing Contaminant Levels in Captured CO2 Streams; (3) An Asse

Dennis Schuetzle; Robert Schuetzle

2010-12-31T23:59:59.000Z

350

Steel-framed buildings: Impacts of wall detail configurations on the whole wall thermal performance  

SciTech Connect

The main objective of this paper is the influence of architectural wall details on the whole wall thermal performance. Whole wall thermal performance analysis was performed for six light gage steel-framed wall systems (some with wood components). For each wall system, all wall details were simulated using calibrated 3-D finite difference computer modeling. The thermal performance of the six steel-framed wall systems included various system details and the whole wall system thermal performance for a typical single-story ranch house. Currently, predicted heat losses through building walls are typically based on measurements of the wall system clear wall area using test methods such as ASTM C 236 or are calculated by one of the procedures recommended in the ASHRAE Handbook of Fundamentals that often is carried out for the clear wall area exclusively. In this paper, clear wall area is defined as the part of the wall system that is free of thermal anomalies due to building envelope details or thermally unaffected by intersections with other surfaces of the building envelope. Clear wall experiments or calculations normally do not include the effects of building envelope details such as corners, window and door openings, and structural intersections with roofs, floors, ceilings, and other walls. In steel-framed wall systems, these details typically consist of much more structural components than the clear wall. For this situation, the thermal properties measured or calculated for the clear wall area do not adequately represent the total wall system thermal performance. Factors that would impact the ability of today`s standard practice to accurately predict the total wall system thermal performance are the accuracy of the calculation methods, the area of the total wall that is clear wall, and the quantity and thermal performance of the various wall system details.

Kosny, J.; Desjarlais, A.O.; Christian, J.E.

1998-06-01T23:59:59.000Z

351

Changing the Rules of the 'ROE': A Reform in Waiting  

SciTech Connect

Congress and FERC recognize the need to attract more investment in transmission. FERC promised to increase cash flow for companies investing in transmission and introduced incremental changes in rates of return. But the agency can do better. FERC should enact comprehensive reform of its return-on-equity calculus to conform policy to market reality. (author)

Rokach, Joshua Z.

2006-05-15T23:59:59.000Z

352

Reform and Regulation of the Electricity Sectors in Developing Countries  

E-Print Network (OSTI)

in investment patterns reflect the differences in the reform strategies adopted by the countries in these regions during the 1990s. By and large, the EAP and SA countries opted for power purchase agreements (PPAs) with independent power producers (IPPs) while...

Jamasb, Tooraj; Littlechild, Stephen C

2004-06-16T23:59:59.000Z

353

Understanding electricity market reforms and the case of Philippine deregulation  

Science Conference Proceedings (OSTI)

The experience of the Philippines offers lessons that should be relevant to any country seeking to deregulate its power industry. Regardless of structure, consumers must face the real price of electricity production and delivery that is closer to marginal cost. Politically motivated prices merely shift the burden from ratepayers to taxpayers. And any reform should work within a reasonable timetable. (author)

Santiago, Andrea; Roxas, Fernando

2010-03-15T23:59:59.000Z

354

Electricity reform and Gains from the reallocation of resources  

SciTech Connect

Perhaps the greatest beneficiary of electricity reform in Australia was the state government of Victoria itself, which was able to reduce debt levels and post budget surpluses even while increasing expenditure and employment levels in education, health care, and law and order. (author)

Abbott, Malcolm

2007-08-15T23:59:59.000Z

355

Communications Technology and Urban Governance Reform: Project Highlights  

E-Print Network (OSTI)

In this paper, we describe highlights of a research project funded by the NSF Digital Government program. The study has examined the impacts of advanced communication technologies in the implementation of a system of neighborhood councils in Los Angeles. It employs social network analysis to chart the development of political networks engendered by the reform and the role of email in shaping these networks.

Christopher Weare

2005-01-01T23:59:59.000Z

356

Financial and ratepayer impacts of nuclear power plant regulatory reform  

SciTech Connect

Three reports - ''The Future Market for Electric Generating Capacity,'' ''Quantitative Analysis of Nuclear Power Plant Licensing Reform,'' and ''Nuclear Rate Increase Study'' are recent studies performed by the Los Alamos National Laboratory that deal with nuclear power. This presents a short summary of these three studies. More detail is given in the reports.

Turpin, A.G.

1985-01-01T23:59:59.000Z

357

Steam Reforming of Low-Level Mixed Waste  

Science Conference Proceedings (OSTI)

Under DOE Contract No. DE-AR21-95MC32091, Steam Reforming of Low-Level Mixed Waste, ThermoChem has successfully designed, fabricated and operated a nominal 90 pound per hour Process Development Unit (PDU) on various low-level mixed waste surrogates. The design construction, and testing of the PDU as well as performance and economic projections for a 500- lb/hr demonstration and commercial system are described. The overall system offers an environmentally safe, non-incinerating, cost-effective, and publicly acceptable method of processing LLMW. The steam-reforming technology was ranked the No. 1 non-incineration technology for destruction of hazardous organic wastes in a study commissioned by the Mixed Waste Focus Area published April 1997.1 The ThermoChem steam-reforming system has been developed over the last 13 years culminating in this successful test campaign on LLMW surrogates. Six surrogates were successfidly tested including a 750-hour test on material simulating a PCB- and Uranium- contaminated solid waste found at the Portsmouth Gaseous Diffusion Plant. The test results indicated essentially total (>99.9999oA) destruction of RCRA and TSCA hazardous halogenated organics, significant levels of volume reduction (> 400 to 1), and retention of radlonuclides in the volume-reduced solids. Cost studies have shown the steam-reforming system to be very cost competitive with more conventional and other emerging technologies.

None

1998-01-01T23:59:59.000Z

358

Fixed-bed reforming with mid-cycle catalyst addition  

Science Conference Proceedings (OSTI)

A fixed-bed catalytic reforming process is described in which on-stream operation is begun with the catalyst retention volume in the first reactor less than 99% full and additional catalyst is added to said reactor while on-stream.

Houston, R.J.; McCoy, C.S.

1981-02-17T23:59:59.000Z

359

Commercialization of a high-performance continuous reforming catalyst  

Science Conference Proceedings (OSTI)

In 1971, the first CCR Platforming process was started up in the US on the Gulf Coast. Twenty-two years later, more than 108 continuous reforming units are operating worldwide. Another 50 CCR Platforming units are in various stages of design, construction, or start-up. Continuous catalytic reforming now represents more than 25% of the world's reforming capacity. Throughout these three decades, the UOP CCR Platforming technology continuously improved in terms of catalyst and process in response to changing industry requirements. Processing conditions in 1993 place tremendous demands on the catalyst in the reforming unit. This paper reviews the challenges and needs of the changing refining industry and the development of a new generation of CCR Platforming catalyst, R-132, and focuses on the first commercial operation of this high-activity, surface-stable catalyst. Case studies show how a refiner can improve margins by using the high activity, yield stability, longer life, and improved chloride retention benefits of this new R-132 Platforming catalyst.

Gilsdorf, N.L.; Doornbos, A.E.; Gevelinger, T.J. (UOP, Des Plaines, IL (United States)); Angelo, C.M.D. (Petrogal Refinaria de Sines (Portugal))

1993-01-01T23:59:59.000Z

360

Tube skin temperature prediction of catalytic reforming unit (CRU) heaters  

Science Conference Proceedings (OSTI)

The maximum duty of reformer heaters is governed by the occurance of maximum tube skin temperature of the heaters. The value of maximum tube skin temperatures of the heaters must not exceed theirs' maximum allowable design temperature. The paper highlights ... Keywords: coke formation, finite element, simulations, tube furnance

Suzana Yusup; Nguyen Duy Vinh; Nurhayati Mellon; Abdullah Hassan

2006-10-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


361

Separation of normally gaseous hydrocarbons from a catalytic reforming effluent and recovery of purified hydrogen  

Science Conference Proceedings (OSTI)

A process for the catalytic reforming of a hydrocarbonaceous feedstock, preferably to produce high quality gasoline boiling range products, is disclosed. Relatively impure hydrogen is separated from the reforming zone effluent, compressed, and recontacted with at least a portion of the liquid reformate product to provide relatively pure hydrogen, a portion of which is recycled to the reforming zone. The balance is further compressed and recontacted with at least a portion of the liquid reformate product to provide an improved recovery of normally gaseous hydrocarbons as well as an improved recovery of purified hydrogen at a pressure suitable for use in the relatively high pressure hydrotreating of sulfur-containing feedstocks.

Coste, A.C.

1982-06-08T23:59:59.000Z

362

BILIWG Meeting: High Pressure Steam Reforming of Bio-Derived Liquids (Presentation)  

NLE Websites -- All DOE Office Websites (Extended Search)

High Pressure Steam Reforming of High Pressure Steam Reforming of Bio-Derived Liquids S. Ahmed, S. Lee, D. Papadias, and R. Kumar November 6, 2007 Laurel, MD Research sponsored by the Hydrogen, Fuel Cells, and Infrastructure Technologies Program of DOE's Office of Energy Efficiency and Renewable Energy Rationale and objective Rationale „ Steam reforming of liquid fuels at high pressures can reduce hydrogen compression costs - Much less energy is needed to pressurize liquids (fuel and water) than compressing gases (reformate or H 2 ) „ High pressure reforming is advantageous for subsequent separations and hydrogen purification Objective „ Develop a reformer design that takes advantage of the savings in compression cost in the steam reforming bio-derived liquid fuels - Metric:

363

Wall Street: Money Never Sleeps (2010) In 2001, Gordon Gekko (Michael Douglas) is released from prison after serving eight years for  

E-Print Network (OSTI)

prison after serving eight years for insider trading and securities fraud. Seven years later, Gekko of an African oil field owned by Churchill Schwartz. The company loses $120 million, and Bretton offers Moore

Schenato, Luca

364

Water Wall Turbine | Open Energy Information  

Open Energy Info (EERE)

Wall Turbine Jump to: navigation, search Name Water Wall Turbine Sector Marine and Hydrokinetic Website http:www.wwturbine.com Region Canada LinkedIn Connections CrunchBase...

365

MOLTEN CARBONATE FUEL CELL POWER PLANT LOCATED AT LADWP MAIN STREET SERVICE CENTER  

DOE Green Energy (OSTI)

The Los Angeles Department of Water and Power (LADWP) has developed one of the most recognized fuel cell demonstration programs in the United States. In addition to their high efficiencies and superior environmental performance, fuel cells and other generating technologies that can be located at or near the load, offers several electric utility benefits. Fuel cells can help further reduce costs by reducing peak electricity demand, thereby deferring or avoiding expenses for additional electric utility infrastructure. By locating generators near the load, higher reliability of service is possible and the losses that occur during delivery of electricity from remote generators are avoided. The potential to use renewable and locally available fuels, such as landfill or sewage treatment waste gases, provides another attractive outlook. In Los Angeles, there are also many oil producing areas where the gas by-product can be utilized. In June 2000, the LADWP contracted with FCE to install and commission the precommercial 250kW MCFC power plant. The plant was delivered, installed, and began power production at the JFB in August 2001. The plant underwent manufacturer's field trials up for 18 months and was replace with a commercial plant in January 2003. In January 2001, the LADWP contracted with FCE to provide two additional 250kW MCFC power plants. These commercial plants began operations during mid-2003. The locations of these plants are at the Terminal Island Sewage Treatment Plant at the Los Angeles Harbor (for eventual operation on digester gas) and at the LADWP Main Street Service Center east of downtown Los Angeles. All three carbonate fuel cell plants received partial funding through the Department of Defense's Climate Change Fuel Cell Buydown Program. This report covers the technical evaluation and benefit-cost evaluation of the Main Street 250kW MCFC power plant during its first year of operation from September 2003 to August 2004. The data for the month of September 2004 was not available at the time this report was prepared. An addendum to this report will be prepared and transmitted to the Department of Energy once this data becomes available. This fuel cell power plant was originally intended to be installed at an American Airlines facility located at Los Angeles International Airport, however, due to difficulties in obtaining a site, the plant was ultimately installed at the LADWP's Distributed Generation Test Facility at it's Main Street Service Center.

William W. Glauz

2004-09-10T23:59:59.000Z

366

Through the wall solar cooker  

SciTech Connect

This patent describes a solar appliance for extending from the interior of a kitchen through an exterior wall of the building and beyond a predetermined distance in a cantilever manner to receive and concentrate in the appliance outside of the building, solar radiation rays for cooking purposes comprising: a housing, the housing being mounted to extend from a kitchen through an external wall of a building and beyond in a cantilever manner and forming a closed oven, the oven comprising a bottom, glass top, a pair of sides and a first end positioned with access from within the kitchen and comprising an oven door, a first reflective panel member mounted above, juxtapositioned to one edge of the glass top for positioning against the outer surface of the external wall and extending laterally therefrom for receiving and directing solar rays impinging thereon through the glass top and into the oven, and a second double-sided reflective panel mounted above and juxtapositioned to the glass top and extending substantially perpendicular to the first reflective panel for receiving solar rays impinging on either side thereof, and directing the solar rays into the oven.

Kerr, B.P.

1987-04-07T23:59:59.000Z

367

Tube wall thickness measurement apparatus  

DOE Patents (OSTI)

An apparatus for measuring the thickness of a tube's wall for the tube's entire length and circumference by determining the deviation of the tube wall thickness from the known thickness of a selected standard item. The apparatus comprises a base and a first support member having first and second ends. The first end is connected to the base and the second end is connected to a spherical element. A second support member is connected to the base and spaced apart from the first support member. A positioning element is connected to and movable relative to the second support member. An indicator is connected to the positioning element and is movable to a location proximate the spherical element. The indicator includes a contact ball for first contacting the selected standard item and holding it against the spherical element. The contact ball then contacts the tube when the tube is disposed about the spherical element. The indicator includes a dial having a rotatable needle for indicating the deviation of the tube wall thickness from the thickness of the selected standard item.

Lagasse, Paul R. (Santa Fe, NM)

1987-01-01T23:59:59.000Z

368

Tube wall thickness measurement apparatus  

DOE Patents (OSTI)

An apparatus for measuring the thickness of a tube's wall for the tube's entire length and radius by determining the deviation of the tube wall thickness from the known thickness of a selected standard item. The apparatus comprises a base and a first support member having first and second ends. The first end is connected to the base and the second end is connected to a spherical element. A second support member is connected to the base and spaced apart from the first support member. A positioning element is connected to and movable relative to the second support member. An indicator is connected to the positioning element and is movable to a location proximate the spherical element. The indicator includes a contact ball for first contacting the selected standard item and holding it against the spherical element. The contact ball then contacts the tube when the tube is disposed about the spherical element. The indicator includes a dial having a rotatable needle for indicating the deviation of the tube wall thickness from the thickness of the selected standard item.

Lagasse, P.R.

1985-06-21T23:59:59.000Z

369

Hr. Michael Esposito Audio-Tex Industries, Incorporated 4555 West Addison Street  

Office of Legacy Management (LM)

-- -- Hr. Michael Esposito Audio-Tex Industries, Incorporated 4555 West Addison Street Chicago, Illinois 60641 Dear Mr. Esposito: Enclosed is a copy of the final survey report for your facility in Chicago,. Illinois , which is the site of the former ERA Tool & Engineering Company. The survey report documents the fact that the radiological condition of your facility is in compliance with applicable Department of Energy Guidelines and that no remedial action or further investigaticns are necessary. If you have any questions regarding the survey results or our dssociated actions, contact Mr. James Wagoner of my staff at 301-353-2802. Sincerely, James 3. Fiore, Director Division of Facility and Site Decommissioning Projects Office of Kuclear Energy

370

Main Street Net-Zero Energy Buildings: The Zero Energy Method in Concept and Practice  

NLE Websites -- All DOE Office Websites (Extended Search)

870 870 July 2010 Main Street Net-Zero Energy Buildings: The Zero Energy Method in Concept and Practice Preprint Paul Torcellini, Shanti Pless, and Chad Lobato National Renewable Energy Laboratory Tom Hootman RNL Design Presented at the ASME 2010 4 th International Conference on Energy Sustainability Phoenix, Arizona May 17-22, 2010 NOTICE The submitted manuscript has been offered by an employee of the Alliance for Sustainable Energy, LLC (ASE), a contractor of the US Government under Contract No. DE-AC36-08-GO28308. Accordingly, the US Government and ASE retain a nonexclusive royalty-free license to publish or reproduce the published form of this contribution, or allow others to do so, for US Government purposes. This report was prepared as an account of work sponsored by an agency of the United States government.

371

FOLEY & LARDNER LLP ATTORNEYS AT LAW WASHINGTON HARBOUR 3000 K STREET, N.W.  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

FOLEY FOLEY FOLEY & LARDNER LLP ATTORNEYS AT LAW WASHINGTON HARBOUR 3000 K STREET, N.W. SUITE 600 WASHINGTON, D.C. 20007-5109 202.672.5300 TEL 202.672.5399 FAX foley.com WRITER'S DIRECT LINE 202.672.5442 jsnewman©foley.corn EMAIL December 13, 2010 VIA E-Mail (Celia.Sher@hq.doe.gov) Ms. Celia Sher U.S. Department of Energy Office of General Counsel Forrestal Building, GC-71 1000 Independence Avenue, S.W. Washington, D.C. 585-0121 Re: Requested Summary of Telephone Conference Regarding Certification and Compliance Requirements Dear Ms. Sher: On behalf of Johnson Controls, Inc. (JCI), I am providing at your request a summary of the concerns raised during our telephone call on Wednesday, December 8, 2010 concerning the certification and compliance requirements for commercial air conditioning and heat pump

372

The Honorable Richard M. Daley,. Jr. 121 N.. LaSalle Street  

Office of Legacy Management (LM)

Pepartment of Energy Pepartment of Energy Washington, DC 20585 FEB 24 1995 The Honorable Richard M. Daley,. Jr. 121 N.. LaSalle Street Chicago, Illinoi~s 60602 Dear Mayor Daley:. Secretary of Energy Hazel O'Leary has announced a new approach.to openness in the Department.of Energy (DOE) and its communicationswith the public. In . support of this initiative, we are,pleased to.forward the enclosed information related to,the former Wyckoff Steel Co. site in your jurisdiction that performed work for DDE or its predecessor agencies. 'This information is provided for your information, use, and retention. DOE's Formerly Utilized Sites Remedial ActionProgram is responsible for identification of sites used by DOE's predecessor agencies, determining their current radiplogical condition'and, where it has authority, performing

373

The Honorable Richard M., Daley, ~Jr: 121 N. LaSalle Street  

Office of Legacy Management (LM)

Richard M., Daley, ~Jr: Richard M., Daley, ~Jr: \ 121 N. LaSalle Street Chicago, Illinois 60602 ', Dear Mayor Daley.:' / Secretary-of Energy Hazel O'Leary has announced a new approach to openness in the Department of Energy (DOE) and its communications with the public. In support'of this .initiative, we are pleased to forward the.enclosed in7ormatio'n related to the former Crane Co. si,te in your jurisdiction 'that'performed work for DOE or.its predecessor agencies. information, use, and retention. , This in,formation- is provided for your. -\ DOE's Formerly Utilized Sites Remedial Act~ion Program is responsible for ,' identification of sites used by DOE's predecessor. agencies, determining their current .radiological condition and, where it- has authority;. performing

374

Report Period: EIA ID NUMBER: Instructions: (e.g., Street Address, Bldg, Floor, Suite)  

U.S. Energy Information Administration (EIA) Indexed Site

Report Period: Report Period: EIA ID NUMBER: Instructions: (e.g., Street Address, Bldg, Floor, Suite) Secure File Transfer option available at: (e.g., PO Box, RR) Electronic Transmission: The PC Electronic Data Reporting Option (PEDRO) is available. Zip Code: - If interested in software, call (202) 586-9659. Email form to: Fax form to: (202) 586-9772 - - Mail form to: Oil & Gas Survey - - U.S. Department of Energy Ben Franklin Station PO Box 279 Washington, DC 20044-0279 Questions? Call toll free: 1-800-638-8812 OOG.SURVEYS@eia.doe.gov Contact Name: Version No.: 2013.01 Date of this Report: Mo Day State: Year Phone No.: DOMESTIC CRUDE OIL FIRST PURCHASE REPORT Company Name: A completed form must be filed by the 30th calendar day following the end of the report

375

Street N.W., Washington, DC 20036 Letter Electrostatic Force Assisted Exfoliation of  

NLE Websites -- All DOE Office Websites (Extended Search)

LAWRENCE BERKELEY NATL LAB LAWRENCE BERKELEY NATL LAB Nano Letters is published by the American Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Letter Electrostatic Force Assisted Exfoliation of Prepatterned Few-Layer Graphenes into Device Sites Xiaogan Liang, Allan S. P. Chang, Yuegang Zhang, Bruce D. Harteneck, Hyuck Choo, Deirdre L. Olynick, and Stefano Cabrini Nano Lett., Article ASAP Downloaded from http://pubs.acs.org on December 15, 2008 More About This Article Additional resources and features associated with this article are available within the HTML version: * Supporting Information * Access to high resolution figures * Links to articles and content related to this article * Copyright permission to reproduce figures and/or text from this article Electrostatic

376

Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Article  

NLE Websites -- All DOE Office Websites (Extended Search)

Chemical Chemical Society. 1155 Sixteenth Street N.W., Washington, DC 20036 Article Proton Dynamics in N,N,N#,N#-Tetramethylguanidinium Bis(perfluoroethylsulfonyl)imide Protic Ionic Liquid Probed by Quasielastic Neutron Scattering Eugene Mamontov, Huimin Luo, and Sheng Dai J. Phys. Chem. B, 2009, 113 (1), 159-169 * DOI: 10.1021/jp808102k * Publication Date (Web): 11 December 2008 Downloaded from http://pubs.acs.org on January 2, 2009 More About This Article Additional resources and features associated with this article are available within the HTML version: * Supporting Information * Access to high resolution figures * Links to articles and content related to this article * Copyright permission to reproduce figures and/or text from this article Proton Dynamics in N,N,N',N'-Tetramethylguanidinium

377

Fiber-optic, anti-cycling, high pressure sodium street light control. Final technical progress report  

Science Conference Proceedings (OSTI)

This is the Final Technical Progress Report on a project to develop and market a Fiber-Optic Anti-Cycling High Pressure Sodium Street Light Control. The field test units are now being made with a single vertical PC board design and contains a computer-on-a-chip or PROM IC to take the place of the majority of the components previously contained on the upper logic board. This will reduce the final costs of the unit when it is in production and increase the control`s flexibility. The authors have finished the soft tooling and have made the 400 plastic cases for the field test units. The new configuration of the cases entails a simplified design of the control shell which will have the lenses cast in place. The shell and base plastics are now finished and in final assembly awaiting the completion of the PC boards.

NONE

1995-05-01T23:59:59.000Z

378

The Jamming point street-lamp in the world of granular media  

E-Print Network (OSTI)

The Jamming of soft spheres at zero temperature, the J-point, has been extensively studied both numerically and theoretically and can now be considered as a safe location in the space of models, where a street lamp has been lit up. However, a recent work by Ikeda et al, 2013 reveals that, in the Temperature/Packing fraction parameter space, experiments on colloids are actually rather far away from the scaling regime illuminated by this lamp. Is it that the J-point has little to say about real system? What about granular media? Such a-thermal, frictional, systems are a-priori even further away from the idealized case of thermal soft spheres. In the past ten years, we have systematically investigated horizontally shaken grains in the vicinity of the Jamming transition. We discuss the above issue in the light of very recent experimental results. First, we demonstrate that the contact network exhibits a remarkable dynamics, with strong heterogeneities, which are maximum at a packing fraction phi star, distinct and smaller than the packing fraction phi dagger, where the average number of contact per particle starts to increase. The two cross-overs converge at point J in the zero mechanical excitation limit. Second, a careful analysis of the dynamics on time scales ranging from a minute fraction of the vibration cycle to several thousands of cycles allows us to map the behaviors of this shaken granular system onto those observed for thermal soft spheres and demonstrate that some light of the J-point street-lamp indeed reaches the granular universe.

Corentin Coulais; Robert P. Behringer; Olivier Dauchot

2013-05-03T23:59:59.000Z

379

Reforming petroleum-based fuels for fuel cell vehicles : composition-performance relationships.  

DOE Green Energy (OSTI)

Onboard reforming of petroleum-based fuels, such as gasoline, may help ease the introduction of fuel cell vehicles to the marketplace. Although gasoline can be reformed, it is optimized to meet the demands of ICEs. This optimization includes blending to increase the octane number and addition of oxygenates and detergents to control emissions. The requirements for a fuel for onboard reforming to hydrogen are quite different than those for combustion. Factors such as octane number and flame speed are not important; however, factors such as hydrogen density, catalyst-fuel interactions, and possible catalyst poisoning become paramount. In order to identify what factors are important in a hydrocarbon fuel for reforming to hydrogen and what factors are detrimental, we have begun a program to test various components of gasoline and blends of components under autothermal reforming conditions. The results indicate that fuel composition can have a large effect on reforming behavior. Components which may be beneficial for ICEs for their octane enhancing value were detrimental to reforming. Fuels with high aromatic and naphthenic content were more difficult to reform. Aromatics were also found to have an impact on the kinetics for reforming of paraffins. The effects of sulfur impurities were dependent on the catalyst. Sulfur was detrimental for Ni, Co, and Ru catalysts. Sulfur was beneficial for reforming with Pt catalysts, however, the effect was dependent on the sulfur concentration.

Kopasz, J. P.; Miller, L. E.; Ahmed, S.; Devlin, P. R.; Pacheco, M.

2001-12-04T23:59:59.000Z

380

STATE OF CALIFORNIA --THE RESOURCES PROVIDER Edmund G. Brown Jr., Governor CALIFORNIA ENERGY COMMISSION 1516 Ninth Street Sacramento, California 95814  

E-Print Network (OSTI)

electronically, on paper, and orally at Energy Commission hearings. A. A Brief History of the Energy Commission1 STATE OF CALIFORNIA -- THE RESOURCES PROVIDER Edmund G. Brown Jr., Governor CALIFORNIA ENERGY COMMISSION 1516 Ninth Street Sacramento, California 95814 Main website: www.energy.ca.gov INITIAL STATEMENT

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


381

Numerical model to characterize the thermal comfort in new ecodistricts: methodology and validation through the canyon street case  

Science Conference Proceedings (OSTI)

In built-up areas, the urban structures affect the radiative and thermal environment. The numerical simulation models provide informations about urban thermal performance for many ranges of urban configurations. This paper presents a validation of a ... Keywords: CFD model, building heat transfers, coupling model, street canyon, thermo-radiative model

Khaled Athamena; Jean Francois Sini; Julien Guilhot; Jerome Vinet; Maeva Sabre; Jean-Michel Rosant

2011-01-01T23:59:59.000Z

382

Numerical model to characterize the thermal comfort in new eco-districts: methodology and validation through the canyon street case  

Science Conference Proceedings (OSTI)

In built-up areas, the urban structures affect the radiative and thermal environment. The numerical simulation models provide informations about urban thermal performance for many ranges of urban configurations. This paper presents a validation of a ... Keywords: CFD model, building heat transfers, coupling model, street canyon, thermo-radiative model

Khaled Athamena; Jean Francois Sini; Julien Guilhot; Jerome Vinet; Maeva Sabre; Jean-Michel Rosant

2011-01-01T23:59:59.000Z

383

POROUS WALL, HOLLOW GLASS MICROSPHERES  

DOE Green Energy (OSTI)

Hollow Glass Microspheres (HGM) is not a new technology. All one has to do is go to the internet and Google{trademark} HGM. Anyone can buy HGM and they have a wide variety of uses. HGM are usually between 1 to 100 microns in diameter, although their size can range from 100 nanometers to 5 millimeters in diameter. HGM are used as lightweight filler in composite materials such as syntactic foam and lightweight concrete. In 1968 a patent was issued to W. Beck of the 3M{trademark} Company for 'Glass Bubbles Prepared by Reheating Solid Glass Particles'. In 1983 P. Howell was issued a patent for 'Glass Bubbles of Increased Collapse Strength' and in 1988 H. Marshall was issued a patent for 'Glass Microbubbles'. Now Google{trademark}, Porous Wall, Hollow Glass Microspheres (PW-HGMs), the key words here are Porous Wall. Almost every article has its beginning with the research done at the Savannah River National Laboratory (SRNL). The Savannah River Site (SRS) where SRNL is located has a long and successful history of working with hydrogen and its isotopes for national security, energy, waste management and environmental remediation applications. This includes more than 30 years of experience developing, processing, and implementing special ceramics, including glasses for a variety of Department of Energy (DOE) missions. In the case of glasses, SRS and SRNL have been involved in both the science and engineering of vitreous or glass based systems. As a part of this glass experience and expertise, SRNL has developed a number of niches in the glass arena, one of which is the development of porous glass systems for a variety of applications. These porous glass systems include sol gel glasses, which include both xerogels and aerogels, as well as phase separated glass compositions, that can be subsequently treated to produce another unique type of porosity within the glass forms. The porous glasses can increase the surface area compared to 'normal glasses of a 1 to 2 order of magnitude, which can result in unique properties in areas such as hydrogen storage, gas transport, gas separations and purifications, sensors, global warming applications, new drug delivery systems and so on. One of the most interesting porous glass products that SRNL has developed and patented is Porous Wall, Hollow Glass Microspheres (PW-HGMs) that are being studied for many different applications. The European Patent Office (EPO) just recently notified SRS that the continuation-in-part patent application for the PW-HGMs has been accepted. The original patent, which was granted by the EPO on June 2, 2010, was validated in France, Germany and the United Kingdom. The microspheres produced are generally in the range of 2 to 100 microns, with a 1 to 2 micron wall. What makes the SRNL microspheres unique from all others is that the team in Figure 1 has found a way to induce and control porosity through the thin walls on a scale of 100 to 3000 {angstrom}. This is what makes the SRNL HW-HGMs one-of-a-kind, and is responsible for many of their unique properties and potential for various applications, including those in tritium storage, gas separations, H-storage for vehicles, and even a variety of new medical applications in the areas of drug delivery and MRI contrast agents. SRNL Hollow Glass Microspheres, and subsequent, Porous Wall, Hollow Glass Microspheres are fabricated using a flame former apparatus. Figure 2 is a schematic of the apparatus.

Sexton, W.

2012-06-30T23:59:59.000Z

384

In situ Gas Conditioning in Fuel Reforming for Hydrogen Generation  

DOE Green Energy (OSTI)

The production of hydrogen for fuel cell applications requires cost and energy efficient technologies. The Absorption Enhanced Reforming (AER), developed at ZSW with industrial partners, is aimed to simplify the process by using a high temperature in situ CO2 absorption. The in situ CO2 removal results in shifting the steam reforming reaction equilibrium towards increased hydrogen concentration (up to 95 vol%). The key part of the process is the high temperature CO2 absorbent. In this contribution results of Thermal Gravimetric Analysis (TGA) investigations on natural minerals, dolomites, silicates and synthetic absorbent materials in regard of their CO2 absorption capacity and absorption/desorption cyclic stability are presented and discussed. It has been found that the inert parts of the absorbent materials have a structure stabilizing effect, leading to an improved cyclic stability of the materials.

Bandi, A.; Specht, M.; Sichler, P.; Nicoloso, N.

2002-09-20T23:59:59.000Z

385

Contract reform: It`s working at Fernald  

SciTech Connect

DOE`s contract reform initiatives at Fernald and the performance-based system DOE is now using to evaluate FERMCO are key elements to the current and future success of DOE and FERMCO at Fernald. Final cleanup of the Fernald site is planned for completion by 2005 per an accelerated 10-year remediation plan which has been approved by DOE and endorsed by the US EPA, Ohio EPA, and the Fernald Citizens Task Force. Required funding of approximately $276 million plus inflation annually for 10 years to accomplish final cleanup is now being considered by US Congress. Contract reform initiatives and modified performance measurement systems, along with best business practices, are clearing the path for the expedited cleanup of Fernald.

Craig, J. [USDOE Fernald Area Office, Cincinnati, OH (United States); Hunt, A. [Fernald Environmental Restoration Management Corp., Cincinnati, OH (United States)

1996-01-25T23:59:59.000Z

386

Corrosion protection of reforming equipment during regeneration of the catalyst  

Science Conference Proceedings (OSTI)

The authors discuss the important process of catalytic reforming to produce the basic components of high-octane gasolines and aromatic hydrocarbons in petroleum chemistry. Wide use is made of two-stage oxidative regeneration--coke burning and oxychlorination. This increases the activity of the catalysts. The authors developed a two-stage industrial method of corrosion protection for the low-temperature equipment of catalytic reforming plants during catalyst regeneration. The system is washed, before catalyst regeneration, with an aqueous solution of KLOE-15 in order to remove corrosion products already present. During catalyst regeneration, KLOE-15 and a neutralizing additive are fed in. The method is technically simple and economically effective, and has been introduced in a number of petroleum refineries.

Altsybeeva, A.I.; Andreeva, G.A.; Prasolova, O.N.; Ratner, E.M.; Reshetnikov, S.M.; Teslya, B.M.

1986-01-01T23:59:59.000Z

387

Reforming with an improved platinum-containing catalyst  

Science Conference Proceedings (OSTI)

A catalyst is disclosed which comprises a physical particle-form mixture of a Component A and a Component B. Said Component A comprises one or more Group VIII noble metals and combined halogen deposed on a refractory inorganic oxide and said Component B comprising a metal from Group IVB or Group VB of the Periodic Table of Elements and a combined halogen deposed on a refrac inorganic oxide. Such catalyst is suitable for use in a hydrocarbon conversion reaction zone. The catalyst can be employed in a process for the reforming of a hydrocarbon stream, which process comprises contacting said stream in a reaction zone under reforming conditions and in the presence hydrogen with said catalyst. The catalyst is not presulfided. A preferred process comprises contacting a hydrocarbon stream that contains a substantial amount of sulfur.

Pellet, R.J.; Bertolacini, R.J.; Lysholm, D.L.

1983-08-30T23:59:59.000Z

388

Reforming with an improved platinum-containing catalyst  

Science Conference Proceedings (OSTI)

There is disclosed a catalyst, which catalyst comprises a physical particle-form mixture of a component A and a component B , said component A comprising one or more group VIII noble metals and a combined halogen deposed on a refractory inorganic oxide and said component B comprising a metal from group IVB or group VB of the periodic table of elements and a combined halogen deposed on a refractory inorganic oxide. Such catalyst is suitable for use in a hydrocarbon conversion reaction zone. The catalyst can be employed in a process for the reforming of a hydrocarbon stream, which process comprises contacting said stream in a reaction zone under reforming conditions and in the presence of hydrogen with said catalyst. The catalyst is not presulfided. A preferred process comprises contacting a hydrocarbon stream that contains a substantial amount of sulfur.

Bertolacini, R.J.; Lysholm, D.L.; Pellet, R.J.

1982-10-12T23:59:59.000Z

389

First Wall and Operational Diagnostics  

SciTech Connect

In this chapter we review numerous diagnostics capable of measurements at or near the first wall, many of which contribute information useful for safe operation of a tokamak. There are sections discussing infrared cameras, visible and VUV cameras, pressure gauges and RGAs, Langmuir probes, thermocouples, and erosion and deposition measurements by insertable probes and quartz microbalance. Also discussed are dust measurements by electrostatic detectors, laser scattering, visible and IR cameras, and manual collection of samples after machine opening. In each case the diagnostic is discussed with a view toward application to a burning plasma machine such as ITER.

Lasnier, C; Allen, S; Boedo, J; Groth, M; Brooks, N; McLean, A; LaBombard, B; Sharpe, J; Skinner, C; Whyte, D; Rudakov, D; West, W; Wong, C

2006-06-19T23:59:59.000Z

390

Heat-sound insulating wall  

SciTech Connect

The wall comprises a closed acoustic box-structure which is defined by a slightly ribbed sheet and a flat sheet. The boxstructure has lateral ribs which extend beyond the sheet. A panel of high-density mineral wool which is of small thickness is enclosed inside the box-structure. A heat insulator covers the box-structure and the ribs of the box-structure and is protected by an outer trough which has ribs or corrugations perpendicular to the ribs of the box-structure.

Ovaert, F.; Reneault, P.

1980-10-21T23:59:59.000Z

391

Making sense of doctoral training reforms in the social sciences:  

E-Print Network (OSTI)

process, occurring through collective reflection and action, whether at the level of the department, institution or the discipline (eg McAlpine et al 2005). Within the UK, this recognition has led the higher education funding council to support a... of this emerging field of academic practice and point to some of the challenges ahead. Within the field of doctoral education, I suggest that these curriculum reforms are often led by senior academic administrators who put their own policy knowledge to good use...

Mills, David

2009-01-01T23:59:59.000Z

392

Fuel cell system with combustor-heated reformer  

DOE Patents (OSTI)

A fuel cell system including a fuel reformer heated by a catalytic combustor fired by anode effluent and/or fuel from a liquid fuel supply providing fuel for the fuel cell. The combustor includes a vaporizer section heated by the combustor exhaust gases for vaporizing the fuel before feeding it into the combustor. Cathode effluent is used as the principle oxidant for the combustor.

Pettit, William Henry (Rochester, NY)

2000-01-01T23:59:59.000Z

393

Power sector reform, private investment and regional co-operation  

E-Print Network (OSTI)

Europe and stimulated FDI in the power sector, and might have similarly stimulative effects in South Asia, quite apart from creating profitable trade opportunities and increasing regional security of supply and greater resilience against external oil... of the Electricity Reforms Act in 1997 setting up the Regulatory Commission. “The state government has directed district administrators and police officials to support the distribution companies for curtailing frauds, theft, etc., but the actual implementation...

Newbery, David

394

WallBots: interactive wall-crawling robots in the hands of public artists and political activists  

Science Conference Proceedings (OSTI)

Street art and political activism have a rich history of shaping urban landscapes. Our work explores the processes by which public artists and political activists contribute to public spaces, introducing opportunities for HCI researchers to engage with ... Keywords: autonomous agents, public spaces, street art

Stacey Kuznetsov; Eric Paulos; Mark D. Gross

2010-08-01T23:59:59.000Z

395

Steam reforming of low-level mixed waste. Final report  

Science Conference Proceedings (OSTI)

ThermoChem has successfully designed, fabricated and operated a nominal 90 pound per hour Process Development Unit (PDU) on various low-level mixed waste surrogates. The design, construction, and testing of the PDU as well as performance and economic projections for a 300-lb/hr demonstration and commercial system are described. The overall system offers an environmentally safe, non-incinerating, cost-effective, and publicly acceptable method of processing LLMW. The steam-reforming technology was ranked the No. 1 non-incineration technology for destruction of hazardous organic wastes in a study commissioned by the Mixed Waste Focus Area and published in April 1997. The ThermoChem steam-reforming system has been developed over the last 13 years culminating in this successful test campaign on LLMW surrogates. Six surrogates were successfully tested including a 750-hour test on material simulating a PCB- and Uranium-contaminated solid waste found at the Portsmouth Gaseous Diffusion Plant. The test results indicated essentially total (> 99.9999%) destruction of RCRA and TSCA hazardous halogenated organics, significant levels of volume reduction (> 400 to 1), and retention of radionuclides in the volume-reduced solids. Economic evaluations have shown the steam-reforming system to be very cost competitive with more conventional and other emerging technologies.

NONE

1998-06-01T23:59:59.000Z

396

The Effect of Oxygen to Methane Ratio on the Methane-wet Air Autothermal Reforming and Carbon Deposition in the Micro-chamber  

Science Conference Proceedings (OSTI)

Considering the problems of catalyst carbon deposition and reforming endothermic reaction in micro-reforming chamber, coupled methane catalyst partial oxidation and steam methane reforming can make the micro-reforming system auto-supply heat and inhibit ... Keywords: micro-chamber, autothermal reforming, carbon deposition, oxygen to methane ratio

Ran Jingyu; Tu Weifeng

2011-01-01T23:59:59.000Z

397

WHEC 16 / 13-16 June 2006 Lyon France Plasma assisted fuel reforming for on-board hydrogen rich gas production  

E-Print Network (OSTI)

through hydrogen on-board storage. The main reforming technology is catalytic reforming, which has been points are challenges for automotive applications. In parallel with research on catalytic reforming assisted reforming could be used complementary to catalytic reforming to ensure dynamics performance (start

Paris-Sud XI, Université de

398

SRNL POROUS WALL GLASS MICROSPHERES  

DOE Green Energy (OSTI)

The Savannah River National Laboratory (SRNL) has developed a new medium for storage of hydrogen and other gases. This involves fabrication of thin, Porous Walled, Hollow Glass Microspheres (PW-HGMs), with diameters generally in the range of 1 to several hundred microns. What is unique about the glass microballons is that porosity has been induced and controlled within the thin, one micron thick walls, on the scale of 10 to several thousand Angstroms. This porosity results in interesting properties including the ability to use these channels to fill the microballons with special absorbents and other materials, thus providing a contained environment even for reactive species. Gases can now enter the microspheres and be retained on the absorbents, resulting in solid-state and contained storage of even reactive species. Also, the porosity can be altered and controlled in various ways, and even used to filter mixed gas streams within a system. SRNL is involved in about a half dozen different programs involving these PW-HGMs and an overview of some of these activities and results emerging are presented.

Wicks, G; Leung Heung, L; Ray Schumacher, R

2008-04-15T23:59:59.000Z

399

Electrochemical cell apparatus having an integrated reformer-mixer nozzle-mixer diffuser  

DOE Patents (OSTI)

An electrochemical apparatus is made having a generator section containing electrochemical cells, a fresh gaseous feed fuel inlet, a gaseous feed oxidant inlet, and at least one hot gaseous spent fuel recirculation channel, where the spent fuel recirculation channel, passes from the generator chamber to combine with the fresh feed fuel inlet to form a reformable mixture, where a reforming chamber contains an outer portion containing reforming material, an inner portion preferably containing a mixer nozzle and a mixer-diffuser, and a middle portion for receiving spent fuel, where the mixer nozzle and mixer-diffuser are preferably both within the reforming chamber and substantially exterior to the main portion of the apparatus, where the reformable mixture flows up and then backward before contacting the reforming material, and the mixer nozzle can operate below 400 C. 1 figure.

Shockling, L.A.

1991-09-10T23:59:59.000Z

400

Effect of Surface Oxygen Containing Groups on the Catalytic Activity of Multi-walled Carbon Nanotube Supported Pt Catalyst  

Science Conference Proceedings (OSTI)

Multi-walled carbon nanotubes (MWNT) supported platinum catalysts were employed to study the support functionalization on their catalytic performances. The MWNT were subjected to HNO{sub 3} functionalization, in which oxygen-containing-groups (OCGs) were introduced to improve Pt dispersion. The MWNT supports were characterized by nitrogen physisorption and NEXAFS, and the Pt supported on differently functionalized MWNT characterized by X-ray absorption, TEM and both hydrogen and CO chemisorption. Compared to the as received MWNT supports, Pt dispersion is improved on the HNO3 treated MWNT supports, but the turnover frequency (TOF) of aqueous phase reforming decreases by half. The TOF can be recovered by removing the OCGs via high temperature annealing. To further investigate the OCGs effect, different probe reactions, including both steam reforming and liquid phase reforming of hydrocarbon oxygenates and dehydrogenation of alkanes in the liquid and gas phases, have been performed on the MWNT supported catalysts with different OCGs. A comparison of these reaction results suggests that OCGs are only detrimental to reactions in a binary mixture with two components of different hydrophilicity due to their competitive adsorption on the catalyst supports.

X Wang; N Li; J Webb; L Pfefferle; G Haller

2011-12-31T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


401

Measurement of genotoxic air pollutant exposures in street vendors and school children in and near Bangkok  

SciTech Connect

The effects of air pollution on human health are a great concern, particularly in big cities with severe traffic problems such as Bangkok, Thailand. In this study, exposure to genotoxic compounds in ambient air was studied by analysis of particle-associated polycyclic aromatic hydrocarbons (PAHs) and benzene through direct measurement of concentrations in air as well as through the use of different biomarkers of exposure: urinary 1-hydroxypyrene (1-OHP) for PAHs and urinary t,t-muconic acid (t,t-MA) for benzene. The study was conducted in various susceptible groups of the population with different occupations in 5 traffic-congested areas of Bangkok, as well as in primary school children. The level of total PAHs on the main roads at various sites ranged from 7.10 to 83.04 ng/m{sup 3}, while benzene levels ranged from 16.35 to 49.25 ppb. In contrast, ambient levels in nearby temples, the control sites, ranged from 1.67 to 3.04 ng/m{sup 3} total PAHs and 10.16 to 16.25 ppb benzene. Street vendors selling clothes were exposed to 16.07 {+-} 1.64 ng/m{sup 3} total PAHs and 21.97 {+-} 1.50 ppb benzene, levels higher than in monks and nuns residing in nearby temples (5.34 {+-} 0.65 ng/m{sup 3} total PAHs and 13.69 {+-} 0.77 ppb benzene). Grilled-meat vendors in the same area were exposed to both total PAHs and benzene at even higher levels, possibly due to additional formation of PAHs during the grilling of meat (34.27 {+-} 7.02 ng/m{sup 3} total PAHs; 27.49 {+-} 2.72 ppb benzene). At the end of the workday, urinary 1-OHP levels in street vendors (0.12 and 0.15 {mu}mol/mol creatinine in clothes and grilled-meat vendors, respectively) were significantly higher than in controls (0.04 {mu}mol/mol creatinine; P < 0.01). Afternoon urinary t,t-MA levels in both groups of street vendors (0.12 mg/g creatinine) were also significantly higher than in controls (0.08 mg/g creatinine; P < 0.05). School children from two schools in Bangkok were exposed to total PAHs and benzene at levels of 6.70 {+-} 0.47 ng/m{sup 3} and 4.71 {+-} 0.25 ppb, respectively, higher than those to which children living outside the city were exposed (1.25 {+-} 0.24 ng/m{sup 3} total PAHs; 2.10 {+-} 0.16 ppb benzene). At the end of the school day, levels of urinary 1-OHP and t,t-MA were significantly higher (P < 0.001 and P < 0.01, respectively) in Bangkok school children (0.23 {mu}mol/mol creatinine and 0.27 mg/g creatinine, respectively) than in school children from outside Bangkok (0.10 {mu}mol/mol creatinine and 0.08 mg/g creatinine, respectively)

Ruchirawat, Mathuros [Laboratory of Environmental Toxicology, Chulabhorn Research Institute, Bangkok 10210 (Thailand) and Department of Pharmacology, Faculty of Science, Mahidol University, Bangkok 10400 (Thailand)]. E-mail: mathuros@tubtim.cri.or.th; Navasumrit, Panida [Laboratory of Environmental Toxicology, Chulabhorn Research Institute, Bangkok 10210 (Thailand); Settachan, Daam [Laboratory of Environmental Toxicology, Chulabhorn Research Institute, Bangkok 10210 (Thailand); Tuntaviroon, Jantamas [Laboratory of Environmental Toxicology, Chulabhorn Research Institute, Bangkok 10210 (Thailand); Buthbumrung, Nantaporn [Laboratory of Environmental Toxicology, Chulabhorn Research Institute, Bangkok 10210 (Thailand); Sharma, Suman [Laboratory of Environmental Toxicology, Chulabhorn Research Institute, Bangkok 10210 (Thailand)

2005-08-07T23:59:59.000Z

402

Writing on the Streets: Popular Literature and the Bad Black Hero  

E-Print Network (OSTI)

This dissertation examines the various ways in which pop-cultural illustrations of the “bad nigger” figure beginning in the late 1960s helped to shape the kinds of defiant and oppositional practices that define the lives of black male youths today. I offer a brief history of the cultural and literary trope of the so-called “bad nigger.” I not only chart the cultural and political expressions of the “bad nigger” trope from the antebellum South to the industrial North, I also offer a critique of these accounts of defiant black male behavior that have dominated much of the intellectual discourse. Writing on the Streets: Urban Literature’s Black Male Hero does not pretend that the struggles of poor black inner-city life are somehow romantic or dramatic. What this dissertation does do, however, is offer popular black male cultural productions as a new critical site for engaging the cultural politics of economic power and racial oppression. Much of the scholarship on black male youth culture fails to engage popular texts that respond to black peoples’ negotiation of global issues. The works that do engage popular expressions and cultural productions often underestimate the importance violence, defiance, and opposition plays in the construction of a black male identity, not just for poor urban black male youths, but for men of color in general. Thus, this dissertation intends to magnify the need for more critical inquiry into popular cultural productions such as “street literature” and rap music, both of which contain poetic as well as practical elements of community uplift and self-empowerment and engage issues of cultural nihilism and self-destruction. This project’s focus on non-canonical texts follows bell hooks’ methodology and whose intellectual philosophy argues for “learning in relation to living regular life, of using everything we already know to know more. Merging critical thinking in everyday life with knowledge learned in books and through study has been the union of theory and practice that has informed my intellectual cultural work” (hooks 2). My hope, therefore, is that the readings I offer here will open the possibility for scholars and students of literature to consider more earnestly the importance of popular cultural productions in black communities. Furthermore, I write this dissertation in an effort to convince cultural and literary critics to concern themselves with the unique history and plight of poor urban black males confronting oppression and struggling in this criminal society.

Winston, Dennis 1979-

2012-12-01T23:59:59.000Z

403

Beyond National Uniformity: Diverging Local Economic Governance Under Japan's Decentralization Reforms  

E-Print Network (OSTI)

a Research Agenda for Public-Private Partnerships in thesectors in reforms for public-private partnership. Theunder the banner of public-private partnership. New

Lee, Jung Hwan

2010-01-01T23:59:59.000Z

404

Methodology and Estimation of the Welfare Impact of Energy Reforms on Households in Azerbaijan.  

E-Print Network (OSTI)

??ABSTRACT Title of Dissertation: METHODOLOGY AND ESTIMATION OF THE WELFARE IMPACT OF ENERGY REFORMS ON HOUSEHOLDS IN AZERBAIJAN Irina Klytchnikova, Doctor of Philosophy, 2006 Dissertation… (more)

Klytchnikova, Irina

2006-01-01T23:59:59.000Z

405

Regulatory Reform in the Wake of the Financial Crisis of 2007—2008  

E-Print Network (OSTI)

Purpose – The purpose of this paper is to analyse regulatory reform in the wake of the financial crisis of 2007-2008.

Lo, Andrew W.

406

Microchannel steam-methane reforming under constant and variable surface temperature distributions.  

E-Print Network (OSTI)

??Steam-methane reforming is a well understood industrial process used for generating hydrogen and synthesis gas. The reaction is generally carried out with residence times on… (more)

[No author

2010-01-01T23:59:59.000Z

407

A Mixed-Dimensionality Modeling Approach for Interaction of Heterogeneous Steam Reforming Reactions and Heat Transfer.  

E-Print Network (OSTI)

??Hydrogen is most often produced on an industrial scale by catalytic steam methane reforming, an equilibrium-limited, highly endothermic process requiring the substantial addition of heat… (more)

Valensa, Jeroen

2009-01-01T23:59:59.000Z

408

Fuel-flexible partial oxidation reforming of hydrocarbons for automotive applications.  

DOE Green Energy (OSTI)

Micro-reactor tests indicate that our partial oxidation catalyst is fuel-flexible and can reform conventional (gasoline and diesel) and alternative (ethanol, methanol, natural gas) fuels to hydrogen rich product gases with high hydrogen selectivity. Alcohols are reformed at lower temperatures (< 600 C) while alkanes and unsaturated hydrocarbons require slightly higher temperatures. Cyclic hydrocarbons and aromatics have also been reformed at relatively low temperatures, however, a different mechanism appears to be responsible for their reforming. Complex fuels like gasoline and diesel, which are mixtures of a broad range of hydrocarbons, require temperatures of > 700 C for maximum hydrogen production.

Ahmed, S.; Carter, J. D.; Kopasz, J. P.; Krumpelt, M.; Wilkenhoener, R.

1999-06-07T23:59:59.000Z

409

The Politics of Revenue-Raising Tax Reform in Latin America  

E-Print Network (OSTI)

in the region. These rate increases, along with reforms toby the marginal tax rate increase of 1992. Other causallow despite a small rate increase in 2001—interviews with

Fairfield, Tasha

2010-01-01T23:59:59.000Z

410

Hard or Soft? Institutional Reforms and Infrastructure Spending as Determinants of Foreign Direct Investment in China  

E-Print Network (OSTI)

Soft? Institutional Reforms and Infrastructure Spending aswe examine whether hard infrastructure in the form of moreand railroads or soft infrastructure in the form of more

Fung, K. C.; Garcia-Herrero, Alicia; Iizaka, Hitomi; Siu, Alan

2005-01-01T23:59:59.000Z

411

The Ambiguous Transition: Building State Capacity and Expanding Popular Participation in Venezuela's Agrarian Reform  

E-Print Network (OSTI)

El Universal, Caracas, Venezuela. Bengelsdorf, Carollee.Crisis and Reform in Venezuela. ” Journal of Interamerican2):27-61. Datamonitor. (2004). “Venezuela Country Profile. ”

Page, Tiffany Linton

2011-01-01T23:59:59.000Z

412

Heat Transfer Limitations in Hydrogen Production Via Steam Reformation: The Effect of Reactor Geometry  

E-Print Network (OSTI)

Hydrogen production Reactors, M.S. Thesis, University ofREFORMATION: THE EFFECT OF REACTOR GEOMETRY David, R. ,have been manifest with reactors of different geometries. In

Vernon, David R.; Davieau, David D.; Dudgeon, Bryce A.; Erickson, Paul A.

2006-01-01T23:59:59.000Z

413

Sulfur-tolerant natural gas reforming for fuel-cell applications.  

E-Print Network (OSTI)

??An attractive simplification of PEM-FC systems operated with natural gas would be the use of a sulfur tolerant reforming catalyst, but such a catalyst has… (more)

Hennings, Ulrich

2010-01-01T23:59:59.000Z

414

Seismic behavior of geogrid reinforced slag wall  

Science Conference Proceedings (OSTI)

Flexible retaining structures are known with their high performance under earthquake loads. In geogrid reinforced walls the performance of the fill material and the interface of the fill and geogrid controls the performance. Geosynthetic reinforced walls in seismic regions must be safe against not only static forces but also seismic forces. The objective of this study is to determine the behavior of a geogrid reinforced slag wall during earthquake by using shaking table experiments. This study is composed of three stages. In the first stage the physical properties of the material to be used were determined. In the second part, a case history involving the use of slag from steel industry in the construction of geogrid reinforced wall is presented. In the third stage, the results of shaking table tests conducted using model geogrid wall with slag are given. From the results, it is seen that slag can be used as fill material for geogrid reinforced walls subjected to earthquake loads.

Edincliler, Ayse [Bogazici University, Kandilli Observatory and Earthquake Research Institute, Department of Earthquake Engineering, Cengelkoey-Istanbul (Turkey); Baykal, Gokhan; Saygili, Altug [Bogazici University, Department of Civil Engineering, Bebek-Istanbul (Turkey)

2008-07-08T23:59:59.000Z

415

Quantum Fusion of Domain Walls with Fluxes  

E-Print Network (OSTI)

We study how fluxes on the domain wall world volume modify quantum fusion of two distant parallel domain walls into a composite wall. The elementary wall fluxes can be separated into parallel and antiparallel components. The parallel component affects neither the binding energy nor the process of quantum merger. The antiparallel fluxes, instead, increase the binding energy and, against naive expectations, suppress quantum fusion. In the small flux limit we explicitly find the bounce solution and the fusion rate as a function of the flux. We argue that at large (antiparallel) fluxes there exists a critical value of the flux (versus the difference in the wall tensions), which switches off quantum fusion altogether. This phenomenon of flux-related wall stabilization is rather peculiar: it is unrelated to any conserved quantity. Our consideration of the flux-related all stabilization is based on substantiated arguments that fall short of complete proof.

S. Bolognesi; M. Shifman; M. B. Voloshin

2009-07-20T23:59:59.000Z

416

Textural break foundation wall construction modules  

SciTech Connect

Below-grade, textural-break foundation wall structures are provided for inhibiting diffusion and advection of liquids and gases into and out from a surrounding hydrogeologic environment. The foundation wall structure includes a foundation wall having an interior and exterior surface and a porous medium disposed around a portion of the exterior surface. The structure further includes a modular barrier disposed around a portion of the porous medium. The modular barrier is substantially removable from the hydrogeologic environment.

Phillips, Steven J. (Kennewick, WA)

1990-01-01T23:59:59.000Z

417

Panelized wall system with foam core insulation  

DOE Patents (OSTI)

A wall system includes a plurality of wall members, the wall members having a first metal panel, a second metal panel, and an insulating core between the first panel and the second panel. At least one of the first panel and the second panel include ridge portions. The insulating core can be a foam, such as a polyurethane foam. The foam can include at least one opacifier to improve the k-factor of the foam.

Kosny, Jan (Oak Ridge, TN); Gaskin, Sally (Houston, TX)

2009-10-20T23:59:59.000Z

418

First wall for polarized fusion reactors  

DOE Patents (OSTI)

Depolarization mechanisms arising from the recycling of the polarized fuel at the limiter and the first-wall of a fusion reactor are greater than those mechanisms in the plasma. Rapid depolarization of the plasma is prevented by providing a first-wall or first-wall coating formed of a low-Z, non-metallic material having a depolarization rate greater than 1 sec.sup.-1.

Greenside, Henry S. (Cranbury, NJ); Budny, Robert V. (Princeton, NJ); Post, Jr., Douglass E. (Buttonwood, CT)

1988-01-01T23:59:59.000Z

419

Seismic Response of Reinforced Concrete Walls Project  

Science Conference Proceedings (OSTI)

... data verification and development of improved models; and (2) investigation of global wall bucking in the 2010 Chile earthquake designed using ...

2012-01-20T23:59:59.000Z

420

Engineering secondary cell wall deposition in plants  

loop, biofuels, cell wall, lignin, sacchari?cation, synthetic biology. Summary ... target speci?c cell types such as ?bre and pith cells. It is well

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


421

First wall for polarized fusion reactors  

DOE Patents (OSTI)

A first-wall or first-wall coating for use in a fusion reactor having polarized fuel may be formed of a low-Z non-metallic material having slow spin relaxation, i.e., a depolarization rate greater than 1 sec/sup -1/. Materials having these properties include hydrogenated and deuterated amorphous semiconductors. A method for preventing the rapid depolarization of a polarized plasma in a fusion device may comprise the step of providing a first-wall or first-wall coating formed of a low-Z, non-metallic material having a depolarization rate greater than 1 sec/sup -1/.

Greenside, H.S.; Budny, R.V.; Post, D.E. Jr.

1985-01-29T23:59:59.000Z

422

Superfund Record of Decision (EPA Region 2): Grand Street Mercury Site, Hoboken, NJ, September 30, 1997  

SciTech Connect

This Record of Decision presents the selected remedial action for the Grand Street Mercury Site. The major components of the selected remedy include: permanent relocation of the former residents of the Site; continuation of temporary relocation of the former residents until permanent relocation has been implemented; historic preservation mitigation measures for the buildings at the Site, as appropriate; gross mercury decontamination of the buildings at the Site including recovery of available mercury, whenever possible; identification and abatement of asbestos in the buildings at the Site; removal and recovery of reusable fixtures, appliances, and recyclable scrap metal and other building components; demolition of the two buildings at the Site using measures to minimize releases of mercury into the environment; removal and off-site disposal of all demolition debris at EPA-approved facilities; sampling of soils at the Site; excavation and off-site disposal of contaminated soils at EPA-approved facilities; sampling of soils at off-site adjacent locations; sampling of groundwater at the Site; and assessment of off-site soil and groundwater data to evaluate the need for future remedial action.

1998-01-01T23:59:59.000Z

423

Autothermal and partial oxidation reformer-based fuel processor, method for improving catalyst function in autothermal and partial oxidation reformer-based processors  

DOE Patents (OSTI)

The invention provides a fuel processor comprising a linear flow structure having an upstream portion and a downstream portion; a first catalyst supported at the upstream portion; and a second catalyst supported at the downstream portion, wherein the first catalyst is in fluid communication with the second catalyst. Also provided is a method for reforming fuel, the method comprising contacting the fuel to an oxidation catalyst so as to partially oxidize the fuel and generate heat; warming incoming fuel with the heat while simultaneously warming a reforming catalyst with the heat; and reacting the partially oxidized fuel with steam using the reforming catalyst.

Ahmed, Shabbir; Papadias, Dionissios D.; Lee, Sheldon H. D.; Ahluwalia, Rajesh K.

2013-01-08T23:59:59.000Z

424

Columbia River Hatchery Reform System-Wide Report.  

SciTech Connect

The US Congress funded the Puget Sound and Coastal Washington Hatchery Reform Project via annual appropriations to the US Fish and Wildlife Service (USFWS) beginning in fiscal year 2000. Congress established the project because it recognized that while hatcheries have a necessary role to play in meeting harvest and conservation goals for Pacific Northwest salmonids, the hatchery system was in need of comprehensive reform. Most hatcheries were producing fish for harvest primarily to mitigate for past habitat loss (rather than for conservation of at-risk populations) and were not taking into account the effects of their programs on naturally spawning populations. With numerous species listed as threatened or endangered under the Endangered Species Act (ESA), conservation of salmon in the Puget Sound area was a high priority. Genetic resources in the region were at risk and many hatchery programs as currently operated were contributing to those risks. Central to the project was the creation of a nine-member independent scientific review panel called the Hatchery Scientific Review Group (HSRG). The HSRG was charged by Congress with reviewing all state, tribal and federal hatchery programs in Puget Sound and Coastal Washington as part of a comprehensive hatchery reform effort to: conserve indigenous salmonid genetic resources; assist with the recovery of naturally spawning salmonid populations; provide sustainable fisheries; and improve the quality and cost-effectiveness of hatchery programs. The HSRG worked closely with the state, tribal and federal managers of the hatchery system, with facilitation provided by the non-profit organization Long Live the Kings and the law firm Gordon, Thomas, Honeywell, to successfully complete reviews of over 200 hatchery programs at more than 100 hatcheries across western Washington. That phase of the project culminated in 2004 with the publication of reports containing the HSRG's principles for hatchery reform and recommendations for Puget Sound/Coastal Washington hatchery programs, followed by the development in 2005 of a suite of analytical tools to support application of the principles (all reports and tools are available at www.hatcheryreform.us). In 2005, Congress directed the National Oceanic and Atmospheric Administration-Fisheries (NOAA Fisheries) to replicate the Puget Sound and Coastal Washington Hatchery Reform Project in the Columbia River Basin. The HSRG was expanded to 14 members to include individuals with specific knowledge about the Columbia River salmon and steelhead populations. This second phase was initially envisioned as a one-year review, with emphasis on the Lower Columbia River hatchery programs. It became clear however, that the Columbia River Basin needed to be viewed as an inter-connected ecosystem in order for the review to be useful. The project scope was subsequently expanded to include the entire Basin, with funding for a second year provided by the Bonneville Power Administration (BPA) under the auspices of the Northwest Power and Conservation Council's (NPCC) Fish and Wildlife Program. The objective of the HSRG's Columbia River Basin review was to change the focus of the Columbia River hatchery system. In the past, these hatchery programs have been aimed at supplying adequate numbers of fish for harvest as mitigation primarily for hydropower development in the Basin. A new, ecosystem-based approach is founded on the idea that harvest goals are sustainable only if they are compatible with conservation goals. The challenge before the HSRG was to determine whether or not conservation and harvest goals could be met by fishery managers and, if so, how. The HSRG determined that in order to address these twin goals, both hatchery and harvest reforms are necessary. The HSRG approach represents an important change of direction in managing hatcheries in the region. It provides a clear demonstration that current hatchery programs can indeed be redirected to better meet both conservation and harvest goals. For each Columbia River Basin Environmentally Si

Warren, Dan [Hatchery Scientific Review Group

2009-04-16T23:59:59.000Z

425

Columbia River Hatchery Reform System-Wide Report.  

DOE Green Energy (OSTI)

The US Congress funded the Puget Sound and Coastal Washington Hatchery Reform Project via annual appropriations to the US Fish and Wildlife Service (USFWS) beginning in fiscal year 2000. Congress established the project because it recognized that while hatcheries have a necessary role to play in meeting harvest and conservation goals for Pacific Northwest salmonids, the hatchery system was in need of comprehensive reform. Most hatcheries were producing fish for harvest primarily to mitigate for past habitat loss (rather than for conservation of at-risk populations) and were not taking into account the effects of their programs on naturally spawning populations. With numerous species listed as threatened or endangered under the Endangered Species Act (ESA), conservation of salmon in the Puget Sound area was a high priority. Genetic resources in the region were at risk and many hatchery programs as currently operated were contributing to those risks. Central to the project was the creation of a nine-member independent scientific review panel called the Hatchery Scientific Review Group (HSRG). The HSRG was charged by Congress with reviewing all state, tribal and federal hatchery programs in Puget Sound and Coastal Washington as part of a comprehensive hatchery reform effort to: conserve indigenous salmonid genetic resources; assist with the recovery of naturally spawning salmonid populations; provide sustainable fisheries; and improve the quality and cost-effectiveness of hatchery programs. The HSRG worked closely with the state, tribal and federal managers of the hatchery system, with facilitation provided by the non-profit organization Long Live the Kings and the law firm Gordon, Thomas, Honeywell, to successfully complete reviews of over 200 hatchery programs at more than 100 hatcheries across western Washington. That phase of the project culminated in 2004 with the publication of reports containing the HSRG's principles for hatchery reform and recommendations for Puget Sound/Coastal Washington hatchery programs, followed by the development in 2005 of a suite of analytical tools to support application of the principles (all reports and tools are available at www.hatcheryreform.us). In 2005, Congress directed the National Oceanic and Atmospheric Administration-Fisheries (NOAA Fisheries) to replicate the Puget Sound and Coastal Washington Hatchery Reform Project in the Columbia River Basin. The HSRG was expanded to 14 members to include individuals with specific knowledge about the Columbia River salmon and steelhead populations. This second phase was initially envisioned as a one-year review, with emphasis on the Lower Columbia River hatchery programs. It became clear however, that the Columbia River Basin needed to be viewed as an inter-connected ecosystem in order for the review to be useful. The project scope was subsequently expanded to include the entire Basin, with funding for a second year provided by the Bonneville Power Administration (BPA) under the auspices of the Northwest Power and Conservation Council's (NPCC) Fish and Wildlife Program. The objective of the HSRG's Columbia River Basin review was to change the focus of the Columbia River hatchery system. In the past, these hatchery programs have been aimed at supplying adequate numbers of fish for harvest as mitigation primarily for hydropower development in the Basin. A new, ecosystem-based approach is founded on the idea that harvest goals are sustainable only if they are compatible with conservation goals. The challenge before the HSRG was to determine whether or not conservation and harvest goals could be met by fishery managers and, if so, how. The HSRG determined that in order to address these twin goals, both hatchery and harvest reforms are necessary. The HSRG approach represents an important change of direction in managing hatcheries in the region. It provides a clear demonstration that current hatchery programs can indeed be redirected to better meet both conservation and harvest goals. For each Columbia River Basin Environmentally Significant Unit

Warren, Dan [Hatchery Scientific Review Group

2009-04-16T23:59:59.000Z

426

External Insulation of Masonry Walls and Wood Framed Walls  

Science Conference Proceedings (OSTI)

The use of exterior insulation on a building is an accepted and effective means to increase the overall thermal resistance of the assembly that also has other advantages of improved water management and often increased air tightness of building assemblies. For thin layers of insulation (1" to 1 1/2"), the cladding can typically be attached directly through the insulation back to the structure. For thicker insulation layers, furring strips have been added as a cladding attachment location. This approach has been used in the past on numerous Building America test homes and communities (both new and retrofit applications), and has been proven to be an effective and durable means to provide cladding attachment. However, the lack of engineering data has been a problem for many designers, contractors, and code officials. This research project developed baseline engineering analysis to support the installation of thick layers of exterior insulation on existing masonry and frame walls. Furthermore, water management details necessary to integrate windows, doors, decks, balconies and roofs were created to provide guidance on the integration of exterior insulation strategies with other enclosure elements.

Baker, P.

2013-01-01T23:59:59.000Z

427

Regulatory Reform and License Termination Planning in Decommissioning  

SciTech Connect

Decommissioning of commercial nuclear power plants (NPPs) must be safe and cost-effective and consider the needs of a wide range of stakeholders. The creative tension among these objectives has provided opportunities to reform the way these plants are regulated and managed in decommissioning. Enlightened and visionary leaders from the U.S. Nuclear Regulatory Commission (NRC) and industry are seizing these opportunities to create new paradigms for risk-informed regulation; creative stakeholder involvement; and effective, end-state focused, license termination planning.

Michael J. Meisner

2000-06-04T23:59:59.000Z

428

Electricity Reform in Chile: Lessons for Developing Countries  

E-Print Network (OSTI)

% for the country as a whole, but 58% in the central system)7 but as demand increases fossil fuels have become more important (in this it is comparable to Columbia and the south west of Brazil). However Chile is perhaps unusual among developing countries because... of the strength of protection for private property and the stability engendered by the long period of economically disciplined military rule. 2. Chile’s Electricity Reform In 1974 Chile’s electricity utilities were in a mess.8 Inflation, high fuel prices...

Pollitt, Michael G.

2006-03-14T23:59:59.000Z

429

SMALL SCALE FUEL CELL AND REFORMER SYSTEMS FOR REMOTE POWER  

DOE Green Energy (OSTI)

New developments in fuel cell technologies offer the promise of clean, reliable affordable power, resulting in reduced environmental impacts and reduced dependence on foreign oil. These developments are of particular interest to the people of Alaska, where many residents live in remote villages, with no roads or electrical grids and a very high cost of energy, where small residential power systems could replace diesel generators. Fuel cells require hydrogen for efficient electrical production, however. Hydrogen purchased through conventional compressed gas suppliers is very expensive and not a viable option for use in remote villages, so hydrogen production is a critical piece of making fuel cells work in these areas. While some have proposed generating hydrogen from renewable resources such as wind, this does not appear to be an economically viable alternative at this time. Hydrogen can also be produced from hydrocarbon feed stocks, in a process known as reforming. This program is interested in testing and evaluating currently available reformers using transportable fuels: methanol, propane, gasoline, and diesel fuels. Of these, diesel fuels are of most interest, since the existing energy infrastructure of rural Alaska is based primarily on diesel fuels, but this is also the most difficult fuel to reform, due to the propensity for coke formation, due to both the high vaporization temperature and to the high sulfur content in these fuels. There are several competing fuel cell technologies being developed in industry today. Prior work at UAF focused on the use of PEM fuel cells and diesel reformers, with significant barriers identified to their use for power in remote areas, including stack lifetime, system efficiency, and cost. Solid Oxide Fuel Cells have demonstrated better stack lifetime and efficiency in demonstrations elsewhere (though cost still remains an issue), and procuring a system for testing was pursued. The primary function of UAF in the fuel cell industry is in the role of third party independent testing. In order for tests to be conducted, hardware must be purchased and delivered. The fuel cell industry is still in a pre-commercial state, however. Commercial products are defined as having a fixed set of specifications, fixed price, fixed delivery date, and a warrantee. Negotiations with fuel cell companies over these issues are often complex, and the results of these discussions often reveal much about the state of development of the technology. This work includes some of the results of these procurement experiments. Fuel cells may one day replace heat engines as the source of electrical power in remote areas. However, the results of this program to date indicate that currently available hardware is not developed sufficiently for these environments, and that significant time and resources will need to be committed for this to occur.

Dennis Witmer

2003-12-01T23:59:59.000Z

430

DEVELOPMENT OF A CATALYST/SORBENT FOR METHANE REFORMING  

DOE Green Energy (OSTI)

This work has led to the initial development of a very promising material that has the potential to greatly simplify hydrocarbon reforming for the production of hydrogen and to improve the overall efficiency and economics of the process. This material, which was derived from an advanced calcium-based sorbent, was composed of core-in-shell pellets such that each pellet consisted of a CaO core and an alumina-based shell. By incorporating a nickel catalyst in the shell, a combined catalyst and sorbent was prepared to facilitate the reaction of hydrocarbons with steam. It was shown that this material not only catalyzes the reactions of methane and propane with steam, it also absorbs CO{sub 2} simultaneously, and thereby separates the principal reaction products, H{sub 2} and CO{sub 2}. Furthermore, the absorption of CO{sub 2} permits the water gas shift reaction to proceed much further towards completion at temperatures where otherwise it would be limited severely by thermodynamic equilibrium. Therefore, an additional water gas shift reaction step would not be required to achieve low concentrations of CO. In a laboratory test of methane reforming at 600 C and 1 atm it was possible to produce a gaseous product containing 96 mole% H{sub 2} (dry basis) while also achieving a H{sub 2} yield of 95%. Methane reforming under these conditions without CO{sub 2} absorption provided a H{sub 2} concentration of 75 mole% and yield of 82%. Similar results were achieved in a test of propane reforming at 560 C and 1 atm which produced a product containing 96 mole% H{sub 2} while CO{sub 2} was being absorbed but which contained only 69 mole% H{sub 2} while CO{sub 2} was not being absorbed. These results were achieved with an improved catalyst support that was developed by replacing a portion of the {alpha}-alumina in the original shell material with {gamma}-alumina having a much greater surface area. This replacement had the unfortunate consequence of reducing the overall compressive strength of the core-in-shell pellets. Therefore, a preliminary study of the factors that control the surface area and compressive strength of the shell material was conducted. The important factors were identified as the relative concentrations and particle size distributions of the {alpha}-alumina, {gamma}-alumina, and limestone particles plus the calcination temperature and time used for sintering the shell material. An optimization of these factors in the future could lead to the development of a material that has both the necessary mechanical strength and catalytic activity.

B.H. Shanks; T.D. Wheelock; Justinus A. Satrio; Timothy Diehl; Brigitte Vollmer

2004-09-27T23:59:59.000Z

431

Cost Analysis of Bio-Derived Liquids Reforming (Presentation)  

NLE Websites -- All DOE Office Websites (Extended Search)

Analysis of Analysis of Bio-Derived Liquids Reforming Brian James Directed Technologies, Inc. 6 November 2007 This presentation does not contain any proprietary, confidential, or otherwise restricted information Objective * Assess cost of H 2 from bio-derived liquids * Looking at forecourt scale systems: 100-1500kg/day * Emphasis on Ethanol * Looking at both "conventional" and "advanced" systems * Interaction with the Researchers is bi-directional * Researchers help me with catalysts, performance, configurations * I can assist Researchers with system studies, configurations, and system performance estimates * Output of my work will be: * System/Configuration Definition * Performance specification & optimization * Capital cost estimation

432

BronWall: a software system for volumetric quantification of the bronchial wall remodeling in MDCT  

Science Conference Proceedings (OSTI)

This paper develops an original volumetric quantification approach of the bronchial wall remodeling, based on MDCT acquisitions prior/post-medication delivery. The methodology is implemented as a software system -BronWall- integrating 3D segmentation, ... Keywords: 3D image processing, 3D segmentation, bronchial reactivity, software system, volumetric quantification, wall remodeling

A. Saragaglia; C. Fetita; F. Preteux

2006-07-01T23:59:59.000Z

433

Results of the radiological and beryllium verification survey at the Peek Street Site, Schenectady, New York (SY001V)  

Science Conference Proceedings (OSTI)

At the request of the U.S. Department of Energy (DOE), a team from Oak Ridge National Laboratory conducted an independent verification radiological and non-radioactive beryllium survey at the Peek Street site, located at 425 Peek Street, Schenectady, New York. The purpose of the survey, conducted during 1993 and continuing through January 1994, was to confirm the success of the remedial actions performed to remove any beryllium concentrations or radioactive materials in excess of the identified guidelines. The verification survey included surface gamma scans and gamma readings at one meter indoors and outdoors, alpha and beta scans inside the structure, and the collection of soil, dust and debris samples and smears for radionuclide and beryllium analyses. Results of the survey demonstrated that all radiological and beryllium measurements on the property were within applicable DOE guidelines. Based on all data collected, the industrial property at 425 Peek Street and the adjacent state-owned bike path in Schenectady, New York, conforms to all applicable radiological and non-radioactive beryllium guidelines established for this site by DOE and approved by the State of New York.

Foley, R.D.; Johnson, C.A.; Carrier, R.F.; Allred, J.F.

1994-10-01T23:59:59.000Z

434

New Corrosion Resistance Bar in Sandwich Wall  

Science Conference Proceedings (OSTI)

Sandwich masonry wall is an energy-saving composite wall with good mechanical properties and durability. But the adhesion strength to its tie bar affects its permanence. In order to simple the traditional production processes, a new method was proposed. ... Keywords: energy-saving, durability, steel bar, insulation

Li Yancang; Ge Xiaohua; Wang Fengxin

2010-03-01T23:59:59.000Z

435

Fire performance of single leaf masonry walls  

Science Conference Proceedings (OSTI)

A finite element model called MasSET has been developed which is capable of predicting the structural behaviour of single leaf masonry walls subject to elevated temperatures. The analysis models a slice through the wall as a column strip in plane stress, ... Keywords: boundary conditions, eccentricity, finite element model, masonry in fire, slenderness ratio

A. Nadjai; M. O'Gara; F. Ali

2001-09-01T23:59:59.000Z

436

A flexible computer software package for industrial steam reformers and methanators based on rigorous heterogeneous mathematical models  

Science Conference Proceedings (OSTI)

An advanced software package for industrial steam reformers based upon heterogeneous models for the catalyst tube is developed and successfully checked against a number of top-fired and side-fired industrial reformers. The package is further developed ...

F. M. Alhabdan; M. A. Abashar; S. S. E. Elnashaie

1992-11-01T23:59:59.000Z

437

Wall System Innovations: Familiar Materials, Better Performance  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

1 1 Wall System Innovation Vladimir Kochkin Joseph Wiehagen April 2013 Wall Innovation Metrics  High R (thermal and air barrier)  High Performance  Durable, structural  Build-able  Low transition risk to builders  50% Building America Goal  ≈ R25+ (CZ 4 and higher) 2 Background  Technologies for high-R walls have been proposed and used for over 25 years  But real market penetration is very low  Often the last EE measure implemented by builders (e.g. E*) 3 Background  High-R wall solutions have not achieved a broad level of standardization and commonality  A large set of methods and materials entered the market  Multiple and conflicting details  Wall characteristics are more critical = RISK 4 New Home Starts -

438

2003 Plant Cell Walls Gordon Conference  

DOE Green Energy (OSTI)

This conference will address recent progress in many aspects of cell wall biology. Molecular, genetic, and genomic approaches are yielding major advances in our understanding of the composition, synthesis, and architecture of plant cell walls and their dynamics during growth, and are identifying the genes that encode the machinery needed to make their biogenesis possible. This meeting will bring together international scientists from academia, industry and government labs to share the latest breakthroughs and perspectives on polysaccharide biosynthesis, wood formation, wall modification, expansion and interaction with other organisms, and genomic & evolutionary analyses of wall-related genes, as well as to discuss recent ''nanotechnological'' advances that take wall analysis to the level of a single cell.

Daniel J. Cosgrove

2004-09-21T23:59:59.000Z

439

Novel Catalytic Fuel Reforming Using Micro-Technology with Advanced Separations Technology  

E-Print Network (OSTI)

by the combustion of membrane raffinate for the production of clean hydrogen by steam reforming natural gas primary fuel sources from existing production and distribution networks ­ i.e. natural gas, gasoline gas -- optimize catalyst composition and evaluate reforming conditions. · Hydrogen purification using

440

Evaluation of dissociated and steam-reformed methanol as automotive engine fuels  

SciTech Connect

Dissociated and steam reformed methanol were evaluated as automotive engine fuels. Advantages and disadvantages in using methanol in the reformed rather than liquid state are discussed. Engine dynamometer tests were conducted with a four cylinder, 2.3 liter, spark ignition automotive engine to determine performance and emission characteristics operating on simulated dissociated and steam reformed methanol (2H/sub 2/ + CO and 3H/sub 2/ + CO/sub 2/ respectively), and liquid methanol. Results are presented for engine performance and emissions as functions of equivalence ratio, at various throttle settings and engine speeds. Operation on dissociated and steam reformed methanol was characterized by flashback (violent propagation of a flame into the intake manifold) which limited operation to lower power output than was obtainable using liquid methanol. It was concluded that: an automobile could not be operated solely on dissociated or steam reformed methanol over the entire required power range - a supplementary fuel system or power source would be necessary to attain higher powers; the use of reformed methanol, compared to liquid methanol, may result in a small improvement in thermal efficiency in the low power range; dissociated methanol is a better fuel than steam reformed methanol for use in a spark ignition engine; and use of dissociated or steam reformed methanol may result in lower exhaust emissions compared to liquid methanol. 36 references, 27 figures, 3 tables.

Lalk, T.R.; McCall, D.M.; McCanlies, J.M.

1984-05-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


441

Performance of Sulfur Tolerant Reforming Catalysts for Production of Hydrogen from Jet Fuel Simulants  

E-Print Network (OSTI)

ReceiVed August 2, 2007 The development of robust desulfurizers and new reforming catalysts for fuel cells: the desulfurization of jet fuel and the development of sulfur-tolerant reforming catalysts/C) ratios. The water gas shift reaction is then used to convert additional CO into CO2. Nickel has been

Azad, Abdul-Majeed

442

Simulation and Optimization of the Stabilizer Tower Operation at Catalytic Reforming of Esfahan Oil Refining Company  

Science Conference Proceedings (OSTI)

Production of gasoline with low RVP specifications have made the operators of the catalytic reforming unit of Esfahan Oil refining company in Iran to apply new operating conditions. RVP is an abbreviation for Reid Vapor Pressure which is the vapor pressure ... Keywords: RVP, platformate, initial boiling point, catalytic reforming, distillation curve

Ali Izadyar; Bahram Hashemi Shahraki; Ahmad Shariati

2010-01-01T23:59:59.000Z

443

Achieving Universal Coverage through Comprehensive Health Reform: The Vermont Experience – Evaluation Results  

E-Print Network (OSTI)

Vermont’s comprehensive health reform law, the Health Care Affordability Acts (HCAA) for Vermonters, was passed in 2006 with the following three goals in mind: 1. To achieve universal access to affordable health insurance for all Vermonters 2. To improve quality of care and contain costs through health system reform

Ronald Deprez; Sherry Glied; Kira Rodriguez; Bill Perry; Brian Robertson; Nina Schwabe

2011-01-01T23:59:59.000Z

444

Catalytic reforming and hydrocracking of organic compounds employing promoted zinc titanate as the catalytic agent  

Science Conference Proceedings (OSTI)

The catalytic reforming of a feedstock which contains at least one reformable organic compound or the hydrocracking of a feedstock which contains at least one hydrocrackable organic compound is carried out in the presence of a catalyst composition comprising zinc, titanium and rhenium.

Drehman, L.E.; Farha, F.E.

1981-04-21T23:59:59.000Z

445

Catalytic reforming and hydrocracking of organic compounds employing zinc titanate as the catalytic agent  

Science Conference Proceedings (OSTI)

The catalytic reforming of a feedstock which contains at least one reformable organic compound or the hydrocracking of a feedstock which contains at least one hydrocrackable organic compound is carried out in the presence of a catalyst composition comprising zinc and titanium.

Drehman, L.E.; Farha, F.E.; Walker, D.W.

1981-04-21T23:59:59.000Z

446

Electricity Markets: Should the Rest of the World Adopt the UK Reforms?  

E-Print Network (OSTI)

PWP-069 Electricity Markets: Should the Rest of the World Adopt the UK Reforms? Catherine D;1 Electricity Markets: Should the Rest of the World Adopt the UK Reforms?1 By Catherine D. Wolfram2 Britain was one of the first countries to liberalize its electricity industry when it restructured and privatized

California at Berkeley. University of

447

Gregory H. Friedman: Provided for The Committee on Oversight and Government Reform U.S. House of Representatives  

Energy.gov (U.S. Department of Energy (DOE))

Gregory H. Friedman: Provided for The Committee on Oversight and Government Reform U.S. House of Representatives

448

Agenda Setting And The Role Of Leadership In National Health Care Reform During The Early 1990s  

E-Print Network (OSTI)

Health care reform was the dominant issue on the political agenda during the early 1990s. Few issues

Kang, Michael S,

2006-01-05T23:59:59.000Z

449

Accommodate street vendors during the urban development process : with two empirical cases of Zhu Lian (ZL), and Guan Dong (GD) public markets in Hsinchu City, Taiwan  

E-Print Network (OSTI)

Every day, the recurring scene of conflict between street vendors and municipal authorities can be found in virtually every major city around the world. Through licensing, zoning, or relocating, municipal governments devise ...

Weng, Chia Yang

2013-01-01T23:59:59.000Z

450

The Lessons of Practice: Domestic Policy Reform as a Way to Address Climate  

Open Energy Info (EERE)

The Lessons of Practice: Domestic Policy Reform as a Way to Address Climate The Lessons of Practice: Domestic Policy Reform as a Way to Address Climate Change Jump to: navigation, search Tool Summary LAUNCH TOOL Name: The Lessons of Practice: Domestic Policy Reform as a Way to Address Climate Change Agency/Company /Organization: International Institute for Sustainable Development (IISD) Topics: Policies/deployment programs Resource Type: Lessons learned/best practices Website: www.iisd.org/pdf/2009/bali_2_copenhagen_dom_policy_lessons.pdf The Lessons of Practice: Domestic Policy Reform as a Way to Address Climate Change Screenshot References: The Lessons of Practice[1] Summary "The objectives of this paper are threefold: to review experience to date with policy reforms that can help mitigate climate change, to review work

451

Federal Onshore Oil and Gas Leasing Reform Act of 1987 (FOOGLRA) | Open  

Open Energy Info (EERE)

Page Page Edit with form History Facebook icon Twitter icon » Federal Onshore Oil and Gas Leasing Reform Act of 1987 (FOOGLRA) Jump to: navigation, search Statute Name Federal Onshore Oil and Gas Leasing Reform Act of 1987 (FOOGLRA) Year 1987 Url FederalOnshore1987.jpg Description Another amendment to the Mineral Leasing Act, The Federal Onshore Oil and Gas Leasing Reform Act of 1987 granted the USDA Forest Service the authority to make decisions and implement regulations concerning the leasing of public domain minerals on National Forest System lands containing oil and gas. References Federal Onshore Oil and Gas Leasing Reform Act of 1987 (FOOGLRA)[1] Federal Onshore Oil and Gas Leasing Reform Act of 1987 (FOOGLRA) (30 U.S.C. § 181 et seq.) - Another amendment to the Mineral Leasing Act, The Federal

452

Update on IT Reform at the Department of Energy | Department of Energy  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

Update on IT Reform at the Department of Energy Update on IT Reform at the Department of Energy Update on IT Reform at the Department of Energy June 4, 2012 - 2:14pm Addthis The last 18 months have seen great improvements in the Department of Energy's (DOE) information technology and cybersecurity. A major factor in our success is our alignment with the 25 Point Implementation Plan To Reform Federal Information Technology Management to move to a "Cloud First" environment and maximize the use of shared services to reduce costs and improve IT delivery. Cloud-First/Shared Services: In August 2011, we revamped our online presence by launching Energy.gov and delivering a single platform solution through an open-source content management system and cloud hosting environment. Ultimately, the website reform effort aims to save taxpayers more than $10 million per

453

HYDROGEN PRODUCTION FOR FUEL CELLS VIA REFORMING COAL-DERIVED METHANOL  

DOE Green Energy (OSTI)

Hydrogen can be produced from many feedstocks including coal. The objectives of this project are to establish and prove a hydrogen production pathway from coal-derived methanol for fuel cell applications. This progress report is the tenth report submitted to the DOE reporting on the status and progress made during the course of the project. This report covers the time period of January 1-March 31, 2006. This quarter saw progress in six areas. These areas are: (1) The effect of catalyst dimension on steam reforming, (2) Transient characteristics of autothermal reforming, (3) Rich and lean autothermal reformation startup, (4) Autothermal reformation degradation with coal derived methanol, (5) Reformate purification system, and (6) Fuel cell system integration. All of the projects are proceeding on or slightly ahead of schedule.

Paul A. Erickson

2006-04-01T23:59:59.000Z

454

Separation of normally gaseous hydrocarbons from a catalytic reforming effluent and recovery of purified hydrogen  

Science Conference Proceedings (OSTI)

A process for the catalytic reforming of a hydrocarbonaceous feedstock, preferably to produce high quality gasoline boiling range products, is disclosed. Relatively impure hydrogen is separated from the reforming zone effluent, compressed, and recontacted with at least a portion of the liquid reformate product to provide relatively pure hydrogen, a portion of which is recycled to the reforming zone. The balance is further compressed and recontacted with at least a portion of the liquid reformate product in a plural stage absorption zone to provide an improved recovery of normally gaseous hydrocarbons as well as an improved recovery of purified hydrogen at a pressure suitable, for example, the relatively high pressure hydrotreating of sulfur-containing feedstocks.

O'brien, D.E.

1982-06-08T23:59:59.000Z

455

Catalytic reforming process using noble metal alkaline zeolites  

Science Conference Proceedings (OSTI)

This patent describes improvement in a process wherein a gasoline boiling range hydrocarbonaceous feedstock is catalytically reformed in the presence of hydrogen in a reforming process unit comprised of serially connected reactors wherein each of the reactors contains a supported noble metal-containing catalyst. The improvement comprises the noble-metal catalyst of at least one reactor being selected from the group consisting of alkaline faujasite zeolite, L zeolite and zeolites isostructural thereto, which catalysts are prepared by a: contacting an alkaline faujasite zeolite, L zeolite, or zeolite isostructural thereto, with a noble metal composition selected from Pt(acetylacetonate){sub 2} or Pd(acetylacetonate){sub 2} for an effective amount of time to form a substantially homogeneous mixture and to incorporate the platinum and/or palladium into the near surface regions of the zeolite, but not to disperse the platinum and/or palladium throughout the entire zeolite; and calcining the so treated zeolite at a temperature from about 250 {degrees} C to about 600 {degrees} C for an effective amount of time.

Schweizer, A.E.

1991-02-12T23:59:59.000Z

456

Catalytic Reforming Downstream Processing of Fresh Feed Input  

U.S. Energy Information Administration (EIA) Indexed Site

Process: Catalytic Reforming Catalytic Cracking Catalytic Hydrocracking Delayed and Fluid Coking Period-Unit: Monthly-Thousand Barrels per Day Annual-Thousand Barrels per Day Process: Catalytic Reforming Catalytic Cracking Catalytic Hydrocracking Delayed and Fluid Coking Period-Unit: Monthly-Thousand Barrels per Day Annual-Thousand Barrels per Day Download Series History Download Series History Definitions, Sources & Notes Definitions, Sources & Notes Show Data By: Process Area Apr-13 May-13 Jun-13 Jul-13 Aug-13 Sep-13 View History U.S. 2,563 2,667 2,739 2,807 2,705 2,609 2010-2013 PADD 1 176 178 180 173 156 167 2010-2013 East Coast 166 164 163 161 140 153 2010-2013 Appalachian No. 1 9 14 16 12 15 14 2010-2013 PADD 2 642 638 668 695 677 615 2010-2013 Ind., Ill. and Ky. 426 411 426 460 450 399 2010-2013 Minn., Wis., N. Dak., S. Dak. 67 62 70 72 72 57 2010-2013 Okla., Kans., Mo.

457

[98e]-Catalytic reforming of gasoline and diesel fuel  

DOE Green Energy (OSTI)

Argonne National Laboratory is developing a fuel processor for converting liquid hydrocarbon fuels to a hydrogen-rich product suitable for a polymer electrolyte fuel cell stack. The processor uses an autothermal reformer to convert the feed to a mixture of hydrogen, carbon dioxide, carbon monoxide and water with trace quantities of other components. The carbon monoxide in the product gas is then converted to carbon dioxide in water-gas shift and preferential oxidation reactors. Fuels that have been tested include standard and low-sulfur gasoline and diesel fuel, and Fischer-Tropsch fuels. Iso-octane and n-hexadecane were also examined as surrogates for gasoline and diesel, respectively. Complete conversion of gasoline was achieved at 750 C in a microreactor over a novel catalyst developed at Argonne. Diesel fuel was completely converted at 850 C over this same catalyst. Product streams contained greater than 60% hydrogen on a dry, nitrogen-free basis with iso-octane, gasoline, and n-hexadecane. For a diesel fuel, product streams contained >50% hydrogen on a dry, nitrogen-free basis. The catalyst activity did not significantly decrease over >16 hours operation with the diesel fuel feed. Coke formation was not observed. The carbon monoxide fraction of the product gas could be reduced to as low as 1% on a dry, nitrogen-free basis when the water-gas shift reactors were used in tandem with the reformer.

Pereira, C.; Wilkenhoener, R.; Ahmed, S.; Krumpelt, M.

2000-02-29T23:59:59.000Z

458

Catalysis Letters 59 (1999) 9394 93 Stepwise methane steam reforming: a route to CO-free hydrogen  

E-Print Network (OSTI)

Catalysis Letters 59 (1999) 93­94 93 Stepwise methane steam reforming: a route to CO-free hydrogen-free hydrogen. Keywords: methane decomposition, Ni/zirconia, steam gasification In order to utilize hydrogen of impurities, particularly carbon monoxide. Steam reforming, partial oxidation and au- tothermal reforming [1

Goodman, Wayne

459

Comparing Light-Emitting Diode (LED) Street and Area Lighting to Traditional Lighting Technologies: Assessing LED Performance at Gul f Power in Pensacola, Florida  

Science Conference Proceedings (OSTI)

Manufacturing advances have now made the use of light-emitting diode (LED) technology practical for street and area lighting. To better understand the application, the Electric Power research Institute (EPRI teamed with Southern Company and Gulf Power to install LED street lights at a demonstration site and measure the performance. The data showed several disadvantages such as a lower efficacy compared to traditional technology and lower immunity to electrical disturbances, but advantages in energy savin...

2012-04-21T23:59:59.000Z

460

Fundamental kinetic modeling of the catalytic reforming process  

E-Print Network (OSTI)

In this work, a fundamental kinetic model for the catalytic reforming process has been developed. The complex network of elementary steps and molecular reactions occurring in catalytic reforming has been generated through a computer algorithm characterizing the various species by vectors and Boolean relation matrices. The algorithm is based on the fundamental chemistry occurring on both acid and metal sites of the catalyst. Rates are expressed for each of the elementary steps involved in the transformation of the intermediates. The Hougen-Watson approach is used to express the rates of the molecular reactions occurring on the metal sites of the catalyst. The single event approach is used to account for the effect of structure of reactant and activated complex on the rate coefficients of the elementary steps occurring on the acid sites. This approach recognizes that even if the number of elementary steps is very large they belong to a very limited number of types, and therefore it is possible to express the kinetics of elementary steps by a reduced number of parameters. In addition, the single event approach leads to rate coefficients that are independent of the feedstock, due to their fundamental chemical nature. The total number of parameters at isothermal conditions is 45. To estimate these parameters, an objective function based upon the sum of squares of the residuals was minimized through the Marquardt algorithm. Intraparticle mass transport limitations and deactivation of the catalyst by coke formation are considered in the model. Both the Wilke and the Stefan-Maxwell approaches were used to calculate the concentration gradients inside of the particle. The heterogeneous kinetic model was applied in the simulation of the process for typical industrial conditions for both axial and radial flow fixed bed reactors. The influence of the main process variables on the octane number and reformate volume was investigated and optimal conditions were obtained. Additional aspects studied with the kinetic model are the reduction of aromatics, mainly benzene. The results from the simulations agree with the typical performance found in the industrial process.

Sotelo-Boyas, Rogelio

2005-12-01T23:59:59.000Z

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


461

Bio-Synthetic Wall Systems Visualization  

NLE Websites -- All DOE Office Websites (Extended Search)

Bio-Synthetic Wall Systems Visualization Speaker(s): Maria-Paz Gutierrez Date: December 16, 2008 - 10:00am Location: 90-3075 Seminar HostPoint of Contact: Michael Donn...

462

SO(10) domain-wall brane models  

E-Print Network (OSTI)

We construct domain-wall brane models based on the grand-unification group SO(10), generalising the SU(5) model of Davies, George and Volkas. Motivated by the Dvali-Shifman proposal for the dynamical localisation of gauge bosons, the SO(10) symmetry is spontaneously broken inside the wall. We present two scenarios: in the first, the unbroken subgroup inside the wall is SU(5) x U(1)X, and in the second it is the left-right symmetry group SU(3) x SU(2)L x SU(2)R x U(1)B-L. In both cases we demonstrate that the phenomenologically-correct fermion zero modes can be localised to the wall, and we briefly discuss how the symmetry-breaking dynamics may be extended to induce breaking to the standard model group with subsequent electroweak breaking. Dynamically localised gravity is realised through the type 2 Randall-Sundrum mechanism.

Jayne E. Thompson; Raymond R. Volkas

2009-08-28T23:59:59.000Z

463

ELECTROCHEMISTRY AND ON-CELL REFORMATION MODELING FOR SOLID OXIDE FUEL CELL STACKS  

SciTech Connect

ABSTRACT Providing adequate and efficient cooling schemes for solid-oxide-fuel-cell (SOFC) stacks continues to be a challenge coincident with the development of larger, more powerful stacks. The endothermic steam-methane reformation reaction can provide cooling and improved system efficiency when performed directly on the electrochemically active anode. Rapid kinetics of the endothermic reaction typically causes a localized temperature depression on the anode near the fuel inlet. It is desirable to extend the endothermic effect over more of the cell area and mitigate the associated differences in temperature on the cell to alleviate subsequent thermal stresses. In this study, modeling tools validated for the prediction of fuel use, on-cell methane reforming, and the distribution of temperature within SOFC stacks, are employed to provide direction for modifying the catalytic activity of anode materials to control the methane conversion rate. Improvements in thermal management that can be achieved through on-cell reforming is predicted and discussed. Two operating scenarios are considered: one in which the methane fuel is fully pre-reformed, and another in which a substantial percentage of the methane is reformed on-cell. For the latter, a range of catalytic activity is considered and the predicted thermal effects on the cell are presented. Simulations of the cell electrochemical and thermal performance with and without on-cell reforming, including structural analyses, show a substantial decrease in thermal stresses for an on-cell reforming case with slowed methane conversion.

Recknagle, Kurtis P.; Jarboe, Daniel T.; Johnson, Kenneth I.; Korolev, Alexander; Khaleel, Mohammad A.; Singh, Prabhakar

2007-01-16T23:59:59.000Z

464

Electric and Magnetic Walls on Dielectric Interfaces  

E-Print Network (OSTI)

Sufficient conditions of the existence of electric or magnetic walls on dielectric interfaces are given for a multizone uniform dielectric waveguiding system. If one of two adjacent dielectric zones supports a TEM field distribution while the other supports a TM (TE) field distribution, then the common dielectric interface behaves as an electric (magnetic) wall, that is, the electric (magnetic) field line is perpendicular to the interface while the magnetic (electric) field line is parallel to the interface.

Changbiao Wang

2010-07-20T23:59:59.000Z

465

Thin Wall Cast Iron: Phase II  

DOE Green Energy (OSTI)

The development of thin-wall technology allows the designers of energy consuming equipment to select the most appropriate material based on cost/material properties considerations, and not solely on density. The technology developed in this research project will permit the designers working for the automotive industry to make a better informed choice between competing materials and thin wall cast iron, thus decreasing the overall cost of the automobile.

Doru M. Stefanescu

2005-07-21T23:59:59.000Z

466

Shear wall experiments and design in Japan  

SciTech Connect

This paper summarizes the results of recent survey studies on the available experimental data bases and design codes/standards for reinforced concrete (RC) shear wall structures in Japan. Information related to the seismic design of RC reactor buildings and containment structures was emphasized in the survey. The seismic requirements for concrete structures, particularly those related to shear strength design, are outlined. Detailed descriptions are presented on the development of Japanese shear wall equations, design requirements for containment structures, and ductility requirements.

Park, Y.J.; Hofmayer, C.

1994-12-01T23:59:59.000Z

467

Building Technologies Office: Highly Energy Efficient Wall Systems...  

NLE Websites -- All DOE Office Websites (Extended Search)

Highly Energy Efficient Wall Systems Research Project to someone by E-mail Share Building Technologies Office: Highly Energy Efficient Wall Systems Research Project on Facebook...

468

Membrane reactor advantages for methanol reforming and similar reactions  

Science Conference Proceedings (OSTI)

Membrane reactors achieve efficiencies by combining in one unit a reactor that generates a product with a semipermeable membrane that extracts it. One well-known benefit of this is greater conversion, as removal of a product drives reactions toward completion, but there are several potentially larger advantages that have been largely ignored. Because a membrane reactor tends to limit the partial pressure of the extracted product, it fundamentally changes the way that total pressure in the reactor affects equilibrium conversion. Thus, many gas-phase reactions that are preferentially performed at low pressures in a conventional reactor are found to have maximum conversion at high pressures in a membrane reactor. These higher pressures and reaction conversions allow greatly enhanced product extraction as well. Further, membrane reactors provide unique opportunities for temperature management which have not been discussed previously. These benefits are illustrated for methanol reforming to hydrogen for use with PEM (polymer electrolyte membrane) fuel cells.

Buxbaum, R.E. [REB Research and Consulting Co., Ferndale, MI (United States)

1999-07-01T23:59:59.000Z

469

Petroleum Refinery Catalytic Reforming -- Cutting High Energy Costs  

E-Print Network (OSTI)

Hydrocarbon reforming involves a variety of chemical reactions at high temperatures and pressures in the presence of suitable catalysts. The conversion of naptha to high octane aromatics requires high energy to initiate and sustain the reaction at temperatures of 850-950oF. Hydrogen - rich off - gases are fired in combinations of process furnaces. Heat is transferred to hydrocarbon fluids by radiation, principally. Feed or return stream temperatures determine the need for convection sections. It is essential that the operation and maintenance of these furnaces be optimized to minimize production costs. This paper describes the performance testing and evaluation of a set of ten refinery furnaces used to thermally drive several reforming reactors and to regenerate catalysts. Firing rates provide an input of 216.2 x 106 Btu/hr. to the furnaces, at $1.90 per 106 Btu. The units are fitted with multiple natural draft burners. There is insufficient turbulence and swirl in the burners. Operators manually set up the burners with excessive airflows for normal, full-load firing. These furnaces represent production limits. Products of combustion exhaust at high thermal levels - the range is from 985-1700oF. The mixed gases flow through a "waste heat" boiler, or they bypass the boiler and enter a single stack. Steam generation at 150 psig averages 38,200 lb/hr. Heat is wasted via the bypass at a rate of 41.1x106 Btu /hr. at 1240oF. When airflows are reduced (to 15% excess air) the loss will be 18.7x106 Btu/hr. at 1180oF. Installation of a second, parallel waste heat boiler will result in a saving of l3.4x106 Btu/hr. Energy savings at this furnace complex will be equivalent to $628,700 per year. Investment costs were estimated to be less than $250,000 for the proposed heat trap addition.

Viar, W. L.

1979-01-01T23:59:59.000Z

470

Five Kilowatt Solid Oxide Fuel Cell/Diesel Reformer  

DOE Green Energy (OSTI)

Reducing fossil fuel consumption both for energy security and for reduction in global greenhouse emissions has been a major goal of energy research in the US for many years. Fuel cells have been proposed as a technology that can address both these issues--as devices that convert the energy of a fuel directly into electrical energy, they offer low emissions and high efficiencies. These advantages are of particular interest to remote power users, where grid connected power is unavailable, and most electrical power comes from diesel electric generators. Diesel fuel is the fuel of choice because it can be easily transported and stored in quantities large enough to supply energy for small communities for extended periods of time. This projected aimed to demonstrate the operation of a solid oxide fuel cell on diesel fuel, and to measure the resulting efficiency. Results from this project have been somewhat encouraging, with a laboratory breadboard integration of a small scale diesel reformer and a Solid Oxide Fuel Cell demonstrated in the first 18 months of the project. This initial demonstration was conducted at INEEL in the spring of 2005 using a small scale diesel reformer provided by SOFCo and a fuel cell provided by Acumentrics. However, attempts to integrate and automate the available technology have not proved successful as yet. This is due both to the lack of movement on the fuel processing side as well as the rather poor stack lifetimes exhibited by the fuel cells. Commercial product is still unavailable, and precommercial devices are both extremely expensive and require extensive field support.

Dennis Witmer; Thomas Johnson

2008-12-31T23:59:59.000Z

471

Chemical Looping Reforming for H2, CO and Syngas Production  

SciTech Connect

We demonstrate that the extension of CLC onto oxidants beyond air opens new, highly efficient pathways for production of ultra-pure hydrogen, activation of CO{sub 2} via reduction to CO, and are currently working on production of syngas using nanocomposite Fe-BHA. CLR hold great potential due to fuel flexibility and CO{sub 2} capture. Chemical Looping Combustion (CLC) is a novel clean combustion technology which offers an elegant and highly efficient route for fossil fuel combustion. In CLC, combustion of a fuel is broken down into two spatially separated steps. In the reducer, the oxygen carrier (typically a metal) supplies the stoichiometric oxygen required for fuel combustion. In the oxidizer, the oxygen-depleted carrier is then re-oxidized with air. After condensation of steam from the effluent of the reducer, a high-pressure, high-purity sequestration-ready CO{sub 2} stream is obtained. In the present study, we apply the CLC principle to the production of high-purity H{sub 2}, CO, and syngas streams by replacing air with steam and/or CO{sub 2} as oxidant, respectively. Using H{sub 2}O as oxidant, pure hydrogen streams can be obtained. Similarly, using CO{sub 2} as oxidant, CO is obtained, thus opening an efficient route for CO{sub 2} utilization. Using steam and CO{sub 2} mixtures for carrier oxidation should thus allow production of syngas with adjustable CO:H{sub 2} ratios. Overall, these processes result in Chemical Looping Reforming (CLR), i.e. the net overall reaction is the steam and/or dry reforming of the respective fuel.

Bhavsar,Saurabh; Najera,Michelle; Solunke,Rahul; Veser,Götz

2001-06-06T23:59:59.000Z

472

Autothermal Reforming of Natural Gas to Synthesis Gas  

DOE Green Energy (OSTI)

This Project Final Report serves to document the project structure and technical results achieved during the 3-year project titled Advanced Autothermal Reformer for US Dept of Energy Office of Industrial Technology. The project was initiated in December 2001 and was completed March 2005. It was a joint effort between Sandia National Laboratories (Livermore, CA), Kellogg Brown & Root LLC (KBR) (Houston, TX) and Süd-Chemie (Louisville, KY). The purpose of the project was to develop an experimental capability that could be used to examine the propensity for soot production in an Autothermal Reformer (ATR) during the production of hydrogen-carbon monoxide synthesis gas intended for Gas-to-Liquids (GTL) applications including ammonia, methanol, and higher hydrocarbons. The project consisted of an initial phase that was focused on developing a laboratory-scale ATR capable of reproducing conditions very similar to a plant scale unit. Due to budget constraints this effort was stopped at the advanced design stages, yielding a careful and detailed design for such a system including ATR vessel design, design of ancillary feed and let down units as well as a PI&D for laboratory installation. The experimental effort was then focused on a series of measurements to evaluate rich, high-pressure burner behavior at pressures as high as 500 psi. The soot formation measurements were based on laser attenuation at a view port downstream of the burner. The results of these experiments and accompanying calculations show that soot formation is primarily dependent on oxidation stoichiometry. However, steam to carbon ratio was found to impact soot production as well as burner stability. The data also showed that raising the operating pressure while holding mass flow rates constant results in considerable soot formation at desirable feed ratios. Elementary reaction modeling designed to illuminate the role of CO2 in the burner feed showed that the conditions in the burner allow for the direct participation of CO2 in the oxidation chemistry.

Steven F. Rice; David P. Mann

2007-04-13T23:59:59.000Z

473

,"Catalytic Reforming Downstream Processing of Fresh Feed Input"  

U.S. Energy Information Administration (EIA) Indexed Site

Catalytic Reforming Downstream Processing of Fresh Feed Input" Catalytic Reforming Downstream Processing of Fresh Feed Input" ,"Click worksheet name or tab at bottom for data" ,"Worksheet Name","Description","# Of Series","Frequency","Latest Data for" ,"Data 1","Catalytic Reforming Downstream Processing of Fresh Feed Input",16,"Monthly","9/2013","1/15/2010" ,"Release Date:","11/27/2013" ,"Next Release Date:","Last Week of December 2013" ,"Excel File Name:","pet_pnp_dwns_a_(na)_ydr_mbblpd_m.xls" ,"Available from Web Page:","http://www.eia.gov/dnav/pet/pet_pnp_dwns_a_(na)_ydr_mbblpd_m.htm" ,"Source:","Energy Information Administration"

474

Investigation of Bio-Ethanol Steam Reforming over Cobalt-based Catalysts (Presentation)  

NLE Websites -- All DOE Office Websites (Extended Search)

DOE Bio-Derived Liquids to Hydrogen Distributed DOE Bio-Derived Liquids to Hydrogen Distributed Reforming Working Group (BILIWG) Meeting Investigation of Bio-Ethanol Steam Reforming over Cobalt-based Catalysts Hua Song Lingzhi Zhang Umit S. Ozkan* November 6 th , 2007 Heterogeneous Catalysis Research Group Department of Chemical and Biomolecular Engineering The Ohio State University Columbus, OH 43210 *Ozkan.1@osu.edu Biomass to Hydrogen (Environmentally Friendly) Plant cultivation Plant cultivation Saccharification Saccharification / / Fermentation Fermentation Anaerobic digestion Anaerobic digestion Residues of Residues of agroindustries agroindustries and cultivations and cultivations Municipal Solid Waste Municipal Solid Waste (organic fraction) (organic fraction) Distillation Distillation Reformation of ethanol

475

HYDROGEN GENERATION FROM PLASMATRON REFORMERS: A PROMISING TECHNOLOGY FOR NOX ADSORBER REGENERATION AND OTHER AUTOMOTIVE APPLICATIONS  

DOE Green Energy (OSTI)

Plasmatron reformers are being developed at MIT and ArvinMeritor [1]. In these reformers a special low power electrical discharge is used to promote partial oxidation conversion of hydrocarbon fuels into hydrogen and CO. The partial oxidation reaction of this very fuel rich mixture is difficult to initiate. The plasmatron provides continuous enhanced volume initiation. To minimize electrode erosion and electrical power requirements, a low current, high voltage discharge with wide area electrodes is used. The reformers operate at or slightly above atmospheric pressure. Plasmatron reformers provide the advantages of rapid startup and transient response; efficient conversion of the fuel to hydrogen rich gas; compact size; relaxation or elimination of reformer catalyst requirements; and capability to process difficult to reform fuels, such as diesel and bio-oils. These advantages facilitate use of onboard hydrogen-generation technology for diesel exhaust after-treatment. Plasma-enhanced reformer technology can provide substantial conversion even without the use of a catalyst. Recent progress includes a substantial decrease in electrical power consumption (to about 200 W), increased flow rate (above 1 g/s of diesel fuel corresponding to approximately 40 kW of chemical energy), soot suppression and improvements in other operational features.. Plasmatron reformer technology has been evaluated for regeneration of NOx adsorber after-treatment systems. At ArvinMeritor tests were performed on a dual-leg NOx adsorber system using a Cummins 8.3L diesel engine both in a test cell and on a vehicle. A NOx adsorber system was tested using the plasmatron reformer as a regenerator and without the reformer i.e., with straight diesel fuel based regeneration as the baseline case. The plasmatron reformer was shown to improve NOx regeneration significantly compared to the baseline diesel case. The net result of these initial tests was a significant decrease in fuel penalty, roughly 50% at moderate adsorber temperatures. This fuel penalty improvement is accompanied by a dramatic drop in slipped hydrocarbon emissions, which decreased by 90% or more. Significant advantages are demonstrated across a wide range of engine conditions and temperatures. The study also indicated the potential to regenerate NOx adsorbers at low temperatures where diesel fuel based regeneration is not effective, such as those typical of idle conditions. Two vehicles, a bus and a light duty truck, have been equipped for plasmatron reformer NOx adsorber regeneration tests.

Bromberg, L.; Crane, S; Rabinovich, A.; Kong, Y; Cohn, D; Heywood, J; Alexeev, N.; Samokhin, A.

2003-08-24T23:59:59.000Z

476

Modeling of On-Cell Reforming Reaction for Planar SOFC Stacks  

Science Conference Proceedings (OSTI)

Planar Solid Oxide Fuel Cell (SOFC) stack is known to suffer thermal problem from high stack temperature during operation to generate high current. On-Cell Reforming (OCR) phenomenon is often used to reduce stack temperature by an endothermic reaction of steam-methane reforming process. RIST conducted single-cell experiment to validate modeling tool to simulate OCR performance including temperature measurement. 2D modeling is used to check reforming rate during OCR using temperature measurement data, and 3D modeling is used to check overall thermal performance including furnace boundary conditions.

Yang, Choongmo; Lim, Hyung-Tae; Hwang, Soon Cheol; Kim, Dohyung; Lai, Canhai; Koeppel, Brian J.; Recknagle, Kurtis P.; Khaleel, Mohammad A.

2011-05-30T23:59:59.000Z

477

Refiners look at H sub 2 SO sub 4 alkylation and catalytic reforming  

Science Conference Proceedings (OSTI)

Sulfuric acid alkylation and catalytic reforming drew many questions at the most recent National Petroleum Refiners Association (NPRA) question and answer session on refining and petrochemical technology. At this annual meeting, presubmitted questions are answered by a panel of experts. For more information on the meeting's format, see OGJ, Mar. 16, p. 37. This third and final article in the series of excerpts from the 1991 NPRA Q and A Session examines such pertinent alkylation topics as tertiary amyl methyl ether (TAME) raffinate processing and unit operation during acid runaway. Also discussed are skewed platinum/rhenium reforming catalyst and how catalyst life affects reformate aromatics levels.

Not Available

1992-04-27T23:59:59.000Z

478

Catalytic reforming with a platinum group and phosphorus-containing composition  

Science Conference Proceedings (OSTI)

A new catalyst composition for converting hydrocarbons is disclosed. Also disclosed is a method for making the catalyst. The catalyst comprises a platinum group component and a phosphorous component with a porous support material. The catalyst is made by compositing a platinum group component with a porous support material and then contacting that composite with phosphorus or a compound of phosphorus. In a preferred embodiment of the invention a catalyst comprising platinum, phosphorus and chlorine with alumina is utilized in the catalytic reforming of hydrocarbons boiling in the gasoline range to produce a high octane reformate suitable for gasoline blending or a high aromatics content reformate suitable as a petrochemical feedstock.

Antos, G. J.; Chao, T.-H.

1984-11-20T23:59:59.000Z

479

U.S. Army Corps of Engineers Buffalo District Office 1776 Niagara Street, Buffalo, New York, 14207  

Office of Legacy Management (LM)

Army Corps of Engineers Army Corps of Engineers Buffalo District Office 1776 Niagara Street, Buffalo, New York, 14207 Explanation of Significant Differences for the Rattlesnake Creek Portion of the Ashland Sites Tonawanda, New York September 20, 2004 Formerly Utilized Sites Remedial Action Program Explanation of Significant Differences for the Rattlesnake Creek Portion of the Ashland Sites Table of Contents I. INTRODUCTION 1 II. SITE mSTORY, CONTAMINATION AND SELECTED REMEDy 2 A. Site History 2 B. Original Remedy 3 III. BASIS FOR TmS DOCUMENT.................................*...................*..........*................*.**** 3 A. Summary of Additional Information 3 B. References 4 IV. DESCRIPTION OF SIGNIFICANT DIFFERENCES 4 V. SUPPORT AGENCY COMMENTS 5 VI. STATUTORY DETERMINATIONS 5

480

3610 N. 44th Street, Suite 250, Phoenix, AZ 85018 ● Phone 602-808-2004 ●  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

10 N. 44th Street, Suite 250, Phoenix, AZ 85018 ● Phone 602-808-2004 ● Fax 602-808-2099 ● www.sunzia.net 10 N. 44th Street, Suite 250, Phoenix, AZ 85018 ● Phone 602-808-2004 ● Fax 602-808-2099 ● www.sunzia.net October 17, 2013 Transmitted via electronic mail to juliea.smith@hq.doe.gov and christopher.lawrence@hq.doe.gov Subject: SunZia Southwest Transmission Project comments on Department of Energy's August 29, 2013 Federal Register Notice regarding Improving Performance of Federal Permitting and Review of Infrastructure Projects. The following comments are provided to the Department of Energy (DOE) in response to the agency's request for information on (RFI) the draft Integrated Interagency Pre-Application (IIP) Process. These comments reflect the views and suggestions of the SunZia Southwest Transmission Project (SunZia). The Bureau of Land Management is the lead agency for processing our right-of-

Note: This page contains sample records for the topic "wall street reform" from the National Library of EnergyBeta (NLEBeta).
While these samples are representative of the content of NLEBeta,
they are not comprehensive nor are they the most current set.
We encourage you to perform a real-time search of NLEBeta
to obtain the most current and comprehensive results.


481

An Act to Reform Land Use Planning in the Unorganized Territory (Maine) |  

Energy.gov (U.S. Department of Energy (DOE)) Indexed Site

An Act to Reform Land Use Planning in the Unorganized Territory An Act to Reform Land Use Planning in the Unorganized Territory (Maine) An Act to Reform Land Use Planning in the Unorganized Territory (Maine) < Back Eligibility Agricultural Commercial Investor-Owned Utility Local Government Municipal/Public Utility Nonprofit Rural Electric Cooperative Schools Tribal Government Utility Savings Category Wind Buying & Making Electricity Program Info State Maine Program Type Siting and Permitting Provider Conservation An Act to Reform Land Use Planning in the Unorganized Territory alters the makeup and responsibilities of Maine's Land Use Regulation Commission (LURC). It took effect on August 29, 2012 and changed the Commission's name to the Land Use Planning Commission. Under the Act, permitting review for significant projects, such as

482

Incentives in Water Management Reform: Assessing the Effect on Water Use,  

NLE Websites -- All DOE Office Websites (Extended Search)

Incentives in Water Management Reform: Assessing the Effect on Water Use, Incentives in Water Management Reform: Assessing the Effect on Water Use, Production and Poverty in the Yellow River Basin Speaker(s): Jinixia Wang Date: May 22, 2003 - 12:00pm Location: Bldg. 90 The purpose of this presentation is to better understand water management reform in China's rural communities, focusing on the effect of incentives to water managers on the nation's water resources and the welfare of the rural population. Based on a survey study in the Yellow River Basin, our findings show that Water User Associations and contracting have begun to systematically replace traditional forms of collective management. The analysis demonstrates, however, that it is not a nominal implementation of the reform that matters, but rather it is a creation of new management

483

The risk of reform : privatisation and liberalisation in the Brazilian electric power industry  

E-Print Network (OSTI)

In 1996, when Brazil was well-underway to privatising and liberalising its electric power industry, few would have predicted that within five years the reforms would be a shambles. Like its neighbors Argentina and Chile, ...

Tankha, Sunil, Ph. D. Massachusetts Institute of Technology

2006-01-01T23:59:59.000Z

484

Electricity Sector Reform in Developing Countries: A Survey of Empirical Evidence on Determinants and Performance  

E-Print Network (OSTI)

, patronage, labour opposition to reducing waste, poor collection and other fiscal leakage. Simpler reforms, such as encouraging Independent Power Producers to enter into long-term Power Purchase Agreements with financially fragile counterparts, stored up...

Jamasb, Tooraj; Mota, Raffaella L; Newbery, David; Pollitt, Michael G.

2004-07-09T23:59:59.000Z

485

Synthesis and characterization of 1D ceria nanomaterials for CO oxidation and steam reforming of methanol  

Science Conference Proceedings (OSTI)

Novel one-dimensional (1D) ceria nanostructure has been investigated as a promising and practical approach for the reforming of methanol reaction. Size and shape of the ceria nanomaterials are directly involved with the catalytic activities. Several ...

Sujan Chowdhury; Kuen-Song Lin

2011-01-01T23:59:59.000Z

486

Computational heterogeneous catalysis applied to steam methane reforming over nickel and nickel/silver catalysts  

E-Print Network (OSTI)

The steam methane reforming (SMR) reaction is the primary industrial means for producing hydrogen gas. As such, it is a critical support process for applications including petrochemical processing and ammonia synthesis. ...

Blaylock, Donnie Wayne

2011-01-01T23:59:59.000Z

487

"Quality" control in China's reform era : investigating the suzhi discourse in women's work  

E-Print Network (OSTI)

China's reform era has coincided with an emergence of a Chinese Communist Party-State ideological discourse concerning "population quality." Claims and accusations of 'low quality' are particularly targeted at rural migrant ...

Yip, Cheryl